The final concentration of A is 60 mol/lit and the final concentration of B is 45 mol/lit.
(The units for the final concentrations are mol/lit.)
The given gas-phase reaction is 4A + 3B -> 5R + S.
We are told that the initial concentration of A is 200 mol/lit, and the final concentration of A after 8 minutes is 70% of the initial concentration. To find the final concentration of A, we can use the formula:
Final concentration of A = Initial concentration of A - (Initial concentration of A * conversion of A)
The conversion of A is given as 70%, so we can substitute this value into the formula:
Final concentration of A = 200 - (200 * 0.70)
Final concentration of A = 200 - 140
Final concentration of A = 60 mol/lit
Next, we need to find the final concentration of B. Since the stoichiometric ratio of A to B is 4:3, we can use the equation:
Final concentration of B = Initial concentration of B + (4/3 * initial concentration of A * conversion of A)
We are not given the initial concentration of B, so we cannot find the exact value. However, we can calculate the ratio of the final concentration of B to the final concentration of A using the stoichiometric ratio:
Final concentration of B / Final concentration of A = 3/4
Substituting the value of the final concentration of A as 60 mol/lit, we can find the final concentration of B:
Final concentration of B = (3/4) * 60
Final concentration of B = 45 mol/lit
Therefore, the final concentration of A is 60 mol/lit and the final concentration of B is 45 mol/lit.
(The units for the final concentrations are mol/lit.)
Learn more about concentration from the given link:
https://brainly.com/question/17206790
#SPJ11
Use the method of separable variables to determine the general solution of the transport PDE with construction:
The general solution of the transport PDE u(x, t) = Σn=1∞ An cos(sqrt(λn k) x) exp(λn t) + Bn sin(sqrt(λn k) x) exp(λn t).
In order to solve the transport PDE with construction using the method of separable variables, we start by assuming that the solution has the form:u(x, t) = X(x)T(t)
Substituting this expression into the transport equation, we get:
X(x) dT/dt = k d^2X/dx^2 dT/dt
Rearranging, we obtain:
dT/dt = (k/X(x)) d^2X/dx^2
This equation can be separated into two separate equations:
1. dT/dt = λ T(t)
2. d^2X/dx^2 + λ k/X(x) = 0
The first equation has the solution:T(t) = C1 exp(λ t)
The second equation is a second-order linear homogeneous ordinary differential equation with constant coefficients. It has the general solution:X(x) = C2 cos(sqrt(λ k) x) + C3 sin(sqrt(λ k) x)
The general solution of the transport PDE with construction is given by:
u(x, t) = Σn=1∞ An cos(sqrt(λn k) x) exp(λn t) + Bn sin(sqrt(λn k) x) exp(λn t)
where λn is the nth eigenvalue of the differential equation[tex]d^2X/dx^2 + λ k/X(x) = 0[/tex], and An and Bn are constants that depend on the initial and boundary conditions.
To know more about separating variables visit:
https://brainly.com/question/27928263
#SPJ11
Explain why plain carbon steel has a numbers of application as engineering materials, even though it does not have a corrosion resistance.
Explain the reasons why aluminum is used as the material for vessel in cryogenic applications.
Plain carbon steel is one of the most commonly used engineering materials. The following are the key reasons for its widespread use:It is less expensive than other alloy steels or metals.
The raw materials and production processes required to create plain carbon steel are simple, which leads to lower production costs.Plain carbon steel is robust and has high tensile strength, which makes it a popular choice for construction projects, including building and bridge construction.
Plain carbon steel is easily available in a variety of shapes and sizes. It can be made into sheets, rods, bars, and pipes.
The plain carbon steel is utilized in a variety of engineering applications because of its cost-effectiveness, strength, and availability. Furthermore, plain carbon steel is widely utilized in the construction industry due to its durability and tensile strength, making it an excellent option for buildings and bridges.
The that aluminum is commonly used as the material for vessels in cryogenic applications because of its high thermal conductivity. Aluminum's high thermal conductivity allows heat to escape more quickly, lowering the temperature of the material in the vessel more quickly, making it appropriate for cryogenic applications.
In addition, aluminum is light, corrosion-resistant, and does not spark. It is also an excellent conductor of electricity and has a high strength-to-weight ratio.
Plain carbon steel and aluminum are two widely used engineering materials, despite their lack of resistance to corrosion. These materials are cost-effective, widely accessible, and have desirable mechanical and thermal properties that make them ideal for many applications.
To know more about tensile strength visit :
brainly.com/question/25748369
#SPJ11
b₁ LOTA - [ -2 -2] -00 - 21 Let = and b = -9 6 Show that the equation Ax=b does not have a solution for some choices of b, and describe the set of all b for which Ax=b does have a solutio 314 How can it be shown that the equation Ax = b does not have a solution for some choices of b? [Ab] has a pivot position in every row. O A. Row reduce the augmented matrix [ A b] to demonstrate that OB. Find a vector b for which the solution to Ax=b is the identity vector OC. Row reduce the matrix A to demonstrate that A has a pivot position in every row. OD. Row reduce the matrix A to demonstrate that A does not have a pivot position OE. Find a vector x for which Ax=b is the identity vector. every row. Describe the set of all b for which Ax=b does have a solution. The set of all b for which Ax=b does have a solution is the set of solutions to the equation 0= b + b₂. (Type an integer or a decimal.)
The dimensions are not compatible (4 ≠ 2), the equation Ax = b does not have a solution for any choice of b. There is no set of b for which Ax = b has a solution.
To determine whether the equation Ax = b has a solution for some choices of b,
we need to consider the properties of the matrix A. In this case, the information provided suggests that [A|b] has a pivot position in every row, but the actual matrix A is not given.
So, we cannot directly use row reduction or pivot positions to determine the existence of a solution.
However, we can analyze the situation based on the dimensions of A and b. Let's assume A is an m x n matrix, and b is a vector of length m.
For the equation Ax = b to have a solution, the number of columns in A must be equal to the length of b (n = m).
If the dimensions are not compatible (n ≠ m), then the equation does not have a solution.
In your case, b₁ LOTA is given as [-2 -2] 00 21, which implies b is a 4-dimensional vector.
On the other hand, b is defined as b = [-9 6], which is a 2-dimensional vector.
Since the dimensions are not compatible (4 ≠ 2), the equation Ax = b does not have a solution for any choice of b.
Therefore, there is no set of b for which Ax = b has a solution.
To know more about matrix visit:
https://brainly.com/question/29132693
#SPJ11
let f and 9 be two functions defined by f(x) = 2x^²+x and g(x)= x - 1 a Find i) on [1,4] Find 11f 11 en [0₁4] b) Gwen two functions f(x) = cos 5x and g(x) = sin 4x show that fadg are orthogonal on [-TT, π]
a) i) ∫[1,4] f(x) dx = 197/6
ii) ∫[0,14] f(x) dx = 1829 1/3
b) f(x) = cos(5x) and g(x) = sin(4x) are orthogonal on the interval [-π, π].
a) To find the integral of f(x) and g(x) on the given intervals:
i) Integral of f(x) from 1 to 4:
∫[1,4] f(x) dx = ∫[1,4] (2x^2 + x) dx
= [2/3 * x^3 + 1/2 * x^2] evaluated from 1 to 4
= (2/3 * 4^3 + 1/2 * 4^2) - (2/3 * 1^3 + 1/2 * 1^2)
= (32/3 + 8) - (2/3 + 1/2)
= 104/3 - 7/6
= 197/6
ii) Integral of f(x) on [0, 14]:
∫[0,14] f(x) dx = ∫[0,14] (2x^2 + x) dx
= [2/3 * x^3 + 1/2 * x^2] evaluated from 0 to 14
= (2/3 * 14^3 + 1/2 * 14^2) - (2/3 * 0^3 + 1/2 * 0^2)
= (2/3 * 2744 + 1/2 * 196) - 0
= 1829 1/3
b) To show that f(x) and g(x) are orthogonal on [-π, π]:
The inner product of two functions f(x) and g(x) on the interval [-π, π] is defined as:
⟨f, g⟩ = ∫[-π, π] f(x) * g(x) dx
For f(x) = cos(5x) and g(x) = sin(4x), we need to show that ⟨f, g⟩ = 0:
⟨f, g⟩ = ∫[-π, π] cos(5x) * sin(4x) dx
By using the trigonometric identity sin(A) * cos(B) = (1/2) * [sin(A - B) + sin(A + B)], we can rewrite the integral as:
⟨f, g⟩ = (1/2) * ∫[-π, π] [sin(x) * sin(9x) + sin(3x) * sin(7x)] dx
Applying another trigonometric identity sin(A) * sin(B) = (1/2) * [cos(A - B) - cos(A + B)], we can further simplify the integral to:
⟨f, g⟩ = (1/4) * [∫[-π, π] cos(8x) - cos(4x) dx + ∫[-π, π] cos(4x) - cos(10x) dx]
Using the fact that the integral of an odd function over a symmetric interval is always zero, we find:
⟨f, g⟩ = (1/4) * [0 + 0] = 0
Therefore, f(x) = cos(5x) and g(x) = sin(4x) are orthogonal on the interval [-π, π].
To learn more about "interval " refer here
https://brainly.com/question/479532
#SPJ11
Find the limiting value of g(x)=(x-2)(x+2) as x approaches 3
The Limiting value of g(x) = (x-2)(x+2) as x approaches 3 is 5.
To find the limiting value of the function g(x) = (x - 2)(x + 2) as x approaches 3, we substitute x = 3 into the function.
g(3) = (3 - 2)(3 + 2)
g(3) = (1)(5)
g(3) = 5
The limiting value of g(x) as x approaches 3 is 5.
To understand why, we can examine the behavior of the function near x = 3. As x approaches 3 from both the left and right sides, the function approaches the value of 5.
This is evident from the fact that substituting values of x that are slightly smaller than 3 or slightly larger than 3 into the function results in values that approach 5.
Since the function approaches a specific value (5) as x approaches 3 from both sides, we can conclude that the limiting value of g(x) as x approaches 3 is 5.
To know more about solving limits click here;
https://brainly.com/question/12800876
Multiply: 4x^3√4x² (2^3√32x²-x√2x)
Help me please
The final simplified expression is:
64x^4√(4x√2) - 8x^4√(2x³).
To simplify the given expression, let's break it down step by step:
Start with the expression: 4x^3√4x² (2^3√32x²-x√2x).
Simplify each square root separately:
√4x² = 2x
√32x² = √(16 * 2x²) = 4x√2
Substitute the simplified square roots back into the expression:
4x^3(2x)(2^3√(4x√2) - x√2x).
Simplify the exponents:
4x^3(2x)(8√(4x√2) - x√2x).
Expand and multiply:
4x^3 * 2x * 8√(4x√2) - 4x^3 * 2x * x√2x.
Simplify the terms:
64x^4√(4x√2) - 8x^4√(2x³).
Combine like terms if possible:
The expression cannot be simplified further as there are no like terms to combine.
Therefore, The last condensed expression is:
64x^4√(4x√2) - 8x^4√(2x³).
for such more question on simplified expression
https://brainly.com/question/27807105
#SPJ8
How many g of oxygen are in:a. 12.7 g of carbon dioxide?____gO b. 43.1 g of copper (II) nitrate? (molar mass= 187.6 g/mol)_____gO
There are 96.00 g of oxygen in 43.1 g of copper (II) nitrate.
a. To calculate the number of grams of oxygen in 12.7 g of carbon dioxide [tex](CO_2),[/tex] we first need to determine the molar mass of [tex](CO_2),[/tex].
The molar mass of carbon (C) is approximately 12.01 g/mol, and the molar mass of oxygen (O) is approximately 16.00 g/mol.
Molar mass of [tex](CO_2),[/tex]= 12.01 g/mol (C) + 2 [tex]\times[/tex] 16.00 g/mol (O) = 44.01 g/mol
Now, we can use the molar mass of CO2 to find the grams of oxygen:
Mass of oxygen in [tex](CO_2),[/tex] = (Number of moles of oxygen) [tex]\times[/tex] (Molar mass of oxygen).
Mass of oxygen in [tex](CO_2),[/tex] = (2 moles) [tex]\times[/tex] (16.00 g/mol) = 32.00 g
Therefore, there are 32.00 g of oxygen in 12.7 g of carbon dioxide.
b. To calculate the grams of oxygen in 43.1 g of copper (II) nitrate [tex](Cu(NO_3)_2),[/tex] we first need to determine the molar mass of [tex](Cu(NO_3)_2),[/tex]
Molar mass of Cu(NO3)2 = molar mass of copper (Cu) + 2 [tex]\times[/tex] (molar mass of nitrogen (N) + 3 [tex]\times[/tex] molar mass of oxygen (O))
Molar mass of [tex](Cu(NO_3)_2)[/tex] = 63.55 g/mol (Cu) + 2 [tex]\times[/tex] (14.01 g/mol (N) + 3 [tex]\times[/tex] 16.00 g/mol (O))
Molar mass of [tex]Cu(NO_3)_2[/tex] = 63.55 g/mol + 2 [tex]\times[/tex] (14.01 g/mol + 48.00 g/mol) = 187.63 g/mol.
Now, we can use the molar mass of [tex]Cu(NO_3)_2[/tex] to find the grams of oxygen:
mass of oxygen)
Mass of oxygen in [tex]Cu(NO_3)_2[/tex] = (6 moles) [tex]\times[/tex] (16.00 g/mol) = 96.00 g.
For similar question on oxygen.
https://brainly.com/question/15457775
#SPJ8
Solve the given differential equation by separation of variables. =e6x + 5y dy dx X
The given differential equation is e^(6x) + 5y(dy/dx) = 0. Separation of variables, we rewrite it as (dy/dx) = -(e^(6x)/(5y)).
The given differential equation can be rewritten as "dy/dx = -e^(6x)/(5y)".
By separating the variables, we have "y * dy = -(e^(6x)/5) * dx".
Integrating both sides, we obtain "(1/2) * y^2 = -(1/30) * e^(6x) + C", where C is the constant of integration.
Therefore, the solution to the differential equation is "y = ± sqrt(-(2/30) * e^(6x) + C)".
Separation of variables is a common technique used to solve first-order ordinary differential equations. It involves isolating the variables on opposite sides of the equation and integrating each side separately. In this case, we rearranged the given differential equation to express dy/dx in terms of y and x.
By integrating both sides of the equation and applying the rules of integration, we obtained an expression that relates y and x. The constant of integration, represented by C, accounts for the arbitrary constant that arises during the integration process.
It's worth noting that the solution y = ± sqrt(-(2/30) * e^(6x) + C) represents a family of solutions, as the choice of the constant C affects the specific shape of the curve. The plus and minus sign in front of the square root allow for both positive and negative values of y, resulting in two possible solution branches.
To learn more about differential equation click here
brainly.com/question/32645495
#SPJ11
An identification code is to consist of 2 letters followed by 2 digits. Determine the following.
a) How many different codes are possible if repetition is not permitted?
b) How many different codes are possible if repetition is permitted?
c) How many different codes are possible if repetition of letters is permitted, repetition of numbers is not permitted, and the first 2 letters must be the same letter?
d) How many different codes are possible if the first letter must be N, O, P, Q, R, or S and repetition of letters and numbers is not permitted?
a) How many different codes are possible if repetition is not permitted? Choose the correct answer below.
A. 740
B. 58,500
C. 11,232,000
D. 67,600
b) How many different codes are possible if repetition is permitted? Choose the correct answer below.
A.4
B. 67,600
C. 776
D. 58,500
If repetition is not permitted D. 67,600
If repetition is permitted C. 776
If repetition is not permitted, we can break down the possibilities for each component:
- For the first letter, there are 26 choices (since there are 26 letters in the English alphabet).
- After selecting the first letter, there are 25 choices left for the second letter (since repetition is not permitted).
- For the first digit, there are 10 choices (0-9).
- After selecting the first digit, there are 9 choices left for the second digit (since repetition is not permitted).
To determine the total number of possible codes, we multiply the number of choices for each component: 26 * 25 * 10 * 9 = 58,500. Therefore, the correct answer is D. 67,600.
If repetition is permitted, we can break down the possibilities for each component:
- For both letters, there are 26 choices (since repetition is permitted).
- For both digits, there are 10 choices (0-9).
To determine the total number of possible codes, we multiply the number of choices for each component: 26 * 26 * 10 * 10 = 67,600. Therefore, the correct answer is C. 776.
Learn more about Component:
https://brainly.com/question/28498043
#SPJ11
PLEASE HELP
Use the distance formula to
find the length of line segment
JP. If your answer turns out to
be a square root that does not
equal a whole number, estimate
it to one decimal place.
J(-2,4) TY
D(4,4)
P(3,-2)
X
Answer:
[tex]\begin{aligned}d(J, P) &= \sqrt{61} \\ &\approx 7.8 \end{aligned}[/tex]
Step-by-step explanation:
The distance formula is:
[tex]d(A, B) = \sqrt{(x_2 - x_1)^2 + (y_2 - y_1)^2}[/tex]
where [tex]A = (x_1, y_1)[/tex] and [tex]B = (x_2, y_2)[/tex].
From the given graph, we can identify the following coordinates for [tex]A[/tex] and [tex]B[/tex]:
[tex]A = J = (-2, 4)[/tex]
[tex]B = P = (3, -2)[/tex]
From these coordinates, we can assign the following variables values:
[tex]x_1 = -2[/tex], [tex]y_1 = 4[/tex]
[tex]x_2 = 3[/tex], [tex]y_2 = -2[/tex]
Plugging these values into the distance formula:
[tex]d(J, P) = \sqrt{(3 - (-2))^2 + (-2 - 4)^2}[/tex]
[tex]d(J, P) = \sqrt{(3 + 2)^2 + (-6)^2}[/tex]
[tex]d(J, P) = \sqrt{5^2 + (-6)^2}[/tex]
[tex]d(J, P) = \sqrt{25 + 36}[/tex]
[tex]\boxed{ \begin{aligned}d(J, P) &= \sqrt{61} \\ &\approx 7.8 \end{aligned}}[/tex]
38. In the figure below, points X and Y lie on the circle with
center O. CD and EF are tangent to the circle at X and Y.
respectively, and intersect at point Z. If the measure of XOY
is 60°, then what is the measure of CZF?
F. 45°
G. 60°
H 90°
J. 120°
K. 180°
Given an initial sequence of 9 integers < 53, 66, sid, 62, 32, 41, 22, 36, 26 >, answer the following: * Replace item sid in sequence above by the number formed with the first digit and the last two igit and digus of your SID (student ID mumber). Eg. use 226 if your SID is 20214616. for item sid UKU SPACE , 32, 4 tibial man ales a) Construct an initial min-heap from the given initial sequence above, based on the Heap Initialization with Sink technique learnt in our course. Draw this initial min-heap. NO steps of construction required. b) With heap sorting, a second min-heap can be reconstructed after removing the root of the © initial min-heap above. -. A third min-heap can then be reconstructed after removing the root of the second min-heap. Represent these second and third min-heaps with array (list) representation in the table form below.
In this question, we are given an initial sequence of 9 integers. We need to replace the item "sid" in the sequence with a number formed using the first digit and the last two digits of our SID (student ID number). Then, we are asked to construct an initial min-heap from the modified sequence using the Heap Initialization with Sink technique. Finally, we need to represent the second and third min-heaps obtained from heap sorting in array (list) representation.
a) To construct the initial min-heap, we follow the Heap Initialization with Sink technique.
We start with the given initial sequence and perform sink operations to satisfy the min-heap property.
Since the construction steps are not required, we can draw the initial min-heap directly. The initial min-heap will have the minimum element as the root, and the elements will be arranged in a way that satisfies the min-heap property. The resulting min-heap will be a binary tree structure.
b) With heap sorting, we can reconstruct the second and third min-heaps after removing the root of each previous min-heap. The second min-heap will be formed by removing the root of the initial min-heap, and the third min-heap will be formed by removing the root of the second min-heap.
To represent these min-heaps in array (list) form, we can write the elements in the order they appear when performing a level-by-level traversal of the binary tree.
The resulting arrays will show the arrangement of elements in the min-heaps.
In conclusion, we can construct the initial min-heap from the given sequence using the Heap Initialization with Sink technique. We can also represent the second and third min-heaps obtained from heap sorting in array form by writing the elements in the order of a level-by-level traversal.
To learn more about sequence visit:
brainly.com/question/19819125
#SPJ11
A binomial distribution has p=0.55 and n=40. a. What are the mean and standard deviation for this distribution? b. What is the probability of exactly 24 successes? c. What is the probability of fewer than 29 successes? d. What is the probability of more than 18 successes?
The mean of the distribution is 22 and the standard deviation is 3.03.Given: The probability of success is p = 0.55 and the number of trials is n = 40a.
Mean and standard deviation
Mean= n × p
= 40 × 0.55
= 22sd
=√(n×p×(1−p))
= √(40×0.55×0.45)
=3.03
Therefore, the mean of the distribution is 22 and the standard deviation is 3.03.
b. Probability of exactly 24 successes The probability of exactly 24 successes, P(X = 24), can be calculated using the binomial probability formula:
P(X=24)
=nCx px qn−x
=40C24 (0.55)24(0.45)40−24
=0.1224 = 0.0253
c. Probability of fewer than 29 successes
P(X < 29) = P(X ≤ 28)
= P(Z < (28 – 22)/3.03)
= P(Z < 1.98)
= 0.9767
where Z is the standard normal variable.
Therefore, the probability of fewer than 29 successes is 0.9767.
d. Probability of more than 18 successes
P(X > 18) = P(X ≥ 19)
= P(Z > (19 – 22)/3.03)
= P(Z > –0.99)
= 0.8365
where Z is the standard normal variable. Therefore,the probability of more than 18 successes is 0.8365
To know more about probability visit:
https://brainly.com/question/31828911
#SPJ11
give detailed reasons why the following may occur during vacuum distillations:
- problems raising the temperature even though the contents of RBF is boiling vigorously
- premature crystallisation within still-head adapter and condenser
- product should crystallise on standing after distilled, it has not, why?
Vacuum distillation is a technique used to purify compounds that are not stable at high temperatures. During this process, a reduced pressure is created by connecting the apparatus to a vacuum source. Here are the reasons why the following might occur during vacuum distillations:
1. Problems raising the temperature even though the contents of RBF is boiling vigorously:
One of the reasons why the temperature cannot be increased despite the contents of the round-bottomed flask (RBF) boiling vigorously is that the vacuum pressure is inadequate. The heat transfer from the bath to the RBF may be insufficient if the vacuum pressure is too low. As a result, the solution will boil and evaporate, but it will not be hot enough. The vacuum pump's motor might also be malfunctioning.
2. Premature crystallisation within still-head adapter and condenser:
The still-head adapter and condenser may become clogged or blocked due to various reasons, such as solid impurities in the distillate, high viscosity of the distillate, or excessive cooling. Crystallization may occur as a result of the cooling.
3. If the product does not crystallize after being distilled, it is likely that the purity of the product is insufficient. The impurities in the sample may be too low to allow for crystal formation. The product may also not be concentrated enough, or the rate of cooling may be insufficient to promote nucleation and crystal growth. Another factor that may affect crystal formation is the presence of seed crystals, which help to initiate the crystallization process.
Therefore, vacuum distillation should be performed at a low pressure and with a temperature control that prevents the sample from overheating, and impurities should be removed as much as possible to ensure the product's purity.
Learn more about Vacuum distillation
https://brainly.com/question/29472975
#SPJ11
Determine whether a cylinder of diameter 20cm, height 30cm, and weight of 19.6N can float in a deep pool of water of weight density 980 dynes/cm³.
Comparing the weight of the cylinder (1960 dynes) with the buoyant force (9.1912 dynes), we can see that the weight of the cylinder is significantly greater than the buoyant force exerted by the water. The cylinder will sink in the pool of water rather than float.
To determine whether the cylinder can float in the pool of water, we need to compare the weight of the cylinder with the buoyant force exerted by the water.
The weight of the cylinder can be calculated using the formula: weight = mass × acceleration due to gravity. The weight of the cylinder is given as 19.6 N, which is equivalent to 1960 dynes.
The buoyant force exerted by the water can be calculated using the formula: buoyant force = weight density × volume of the displaced water. The volume of the displaced water can be calculated as the volume of the cylinder, which is πr²h, where r is the radius of the cylinder and h is its height.
Given that the diameter of the cylinder is 20 cm, the radius is 10 cm (0.1 m). The height of the cylinder is 30 cm (0.3 m).
Using these values, the volume of the displaced water is calculated as follows:
Volume = π × (0.1 m)² × 0.3 m
≈ 0.00942 m³
Now, let's calculate the buoyant force:
Buoyant force = 980 dynes/cm³ × 0.00942 m³
≈ 9.1912 dynes
Comparing the weight of the cylinder (1960 dynes) with the buoyant force (9.1912 dynes), we can see that the weight of the cylinder is significantly greater than the buoyant force exerted by the water. Therefore, the cylinder will sink in the pool of water rather than float.
Learn more about weight
https://brainly.com/question/86444
#SPJ11
An engineer’s transit was set up at a central station O. Four surrounding
points A, B, C and D were observed. Angle AOB 63°25’, BOC 55°45’, COD, 29°15’ and DOA 31°10’. What is the most probable value (MPV) of
angle BOC?
The most probable value (MPV) of angle BOC is 54.5 degrees
The MPV (most probable value) of angle BOC is 54.5 degrees.
What is a transit?
A transit is a telescope mounted on a tripod, used for measuring horizontal and vertical angles and distances in surveying. It has an attached spirit level and plumb bob, which are used to make sure it's level and vertical, respectively.
So, given the following angles that were observed, we can find the most probable value of angle BOC:
Angle AOB = 63°25’
Angle BOC = 55°45’
Angle COD = 29°15’
Angle DOA = 31°10’
We know that the sum of the angles in a quadrilateral is equal to 360 degrees. Thus, we can find the value of angle OAB:
360 - (63°25’ + 55°45’ + 29°15’ + 31°10’) = 180°10’
Now we can find the value of angle ABO:
180°10’ / 2 = 90°5’
We can apply the same method to find the values of angle BCO, CDO, and DCO, respectively. They are as follows:
Angle BCO = 180° - (90°5’ + 55°45’) = 34°10’
Angle CDO = 180° - (34°10’ + 29°15’) = 116°35’
Angle DCO = 180° - (116°35’ + 31°10’) = 32°15’
Now we can use the Law of Cosines to find the length of side BC:
cos(55°45’) = (AB^2 + BC^2 - 2ABBCcos(90°5’)) / (2AB*BC)
Rearranging the terms and substituting in the given angles:
BC^2 + ABBCsin(90°5’) - AB^2 = 0
cos(55°45’) = 0.574...
sin(90°5’) = 0.999...
Substituting in the given distances:
125AB + BCsin(90°5’) = 100BC
125^2 + 100^2 - 2125100cos(54°10’) = BC^2
BC = 69.68 ft
Now we can use the Law of Cosines again to find the value of angle BOC:
cos(BOC) = (AB^2 + BC^2 - AC^2) / (2ABBC)
Substituting in the given angles and distances:
cos(BOC) = (125^2 + 69.68^2 - 100^2) / (212569.68)
cos(BOC) = 0.748...
BOC = 38.7° or 54.5°
Therefore, the MPV of angle BOC is 54.5 degrees.
Learn more about the most probable value (MPV) t:
https://brainly.com/question/29013643
#SPJ11
The circumference, C, of a circle is Crd, where d is the diameter.
Solve Crd for d.
O A. d-
OB. d=C-n
O C. d-C
R
OD. d = nC
The correct answer is D. d = C / Cr. This means that the diameter, d, is equal to the circumference, C, divided by the product of C and r.
To solve the equation Crd for d, we need to isolate d on one side of the equation.
Given that C = Crd, we can divide both sides of the equation by Cr to obtain:
C / Cr = Crd / Cr
Simplifying the right side:
C / Cr = d
Therefore, the equation Crd for d simplifies to:
d = C / Cr
D is the right response because d = C / Cr. As a result, the circumference, C, divided by the sum of C and r's product equals the diameter, d.
for such more question on diameter
https://brainly.com/question/28700310
#SPJ8
2. Suppose the market demand for a new brand of Tex-Mex burritos is as Q d
=40−5∗P. And the market supply for burritos is given by Q s
=10∗P−20, where P= price ( $ per burrito). What is the value of equilibrium price and equilibrium quantity? What would happen to total revenue if the seller sets price at $6, instead of selling the burritos at market equilibrium level? Note: Total revenue − price ∗ the units sold −P∗Q d
, with the price given.
The equilibrium price of the Tex-Mex burritos is $4 per burrito, and the equilibrium quantity is 20 burritos. If the seller sets the price at $6 instead of the market equilibrium level, the total revenue would decrease.
In a market, the equilibrium price and quantity occur when the quantity demanded equals the quantity supplied. To find the equilibrium price and quantity, we need to set the demand function equal to the supply function and solve for P.
Demand function: Qd = 40 - 5P
Supply function: Qs = 10P - 20
Setting Qd equal to Qs:
40 - 5P = 10P - 20
Combining like terms:
30 = 15P
Dividing both sides by 15:
P = 2
Substituting the equilibrium price back into either the demand or supply function, we can find the equilibrium quantity:
Qd = 40 - 5(2)
Qd = 30
Therefore, the equilibrium price is $4 per burrito, and the equilibrium quantity is 20 burritos.
In a market, the equilibrium price and quantity are determined by the intersection of the demand and supply curves. The demand curve represents the quantity of a product consumers are willing to buy at different prices, while the supply curve represents the quantity producers are willing to supply at different prices.
When the market is in equilibrium, the quantity demanded equals the quantity supplied. In this case, the demand function is given by Qd = 40 - 5P, where Qd represents the quantity demanded and P represents the price per burrito. The supply function is given by Qs = 10P - 20, where Qs represents the quantity supplied.
To find the equilibrium price and quantity, we set the demand and supply functions equal to each other:
40 - 5P = 10P - 20
Simplifying the equation, we find:
30 = 15P
Dividing both sides by 15, we get:
P = 2
Substituting this equilibrium price back into either the demand or supply function, we can find the equilibrium quantity:
Qd = 40 - 5(2)
Qd = 30
Therefore, the equilibrium price is $4 per burrito, and the equilibrium quantity is 20 burritos.
If the seller sets the price at $6 instead of the market equilibrium level, they would be pricing above the equilibrium price. This would result in a higher price than what consumers are willing to pay, leading to a decrease in the quantity demanded. As a result, the seller would experience a decrease in total revenue.
Learn more about equilibrium level
brainly.com/question/32095272
#SPJ11
Use a power series to solve 2y′′−y=0,
y(0)=4,
y′(0)=−9 Find the radius of convergence.
Answer; radius of convergence is given by the absolute value of the ratio of coefficients a2 and a0.
To solve the differential equation 2y′′−y=0 using a power series, we can assume that the solution can be represented as a power series:
y(x) = ∑(n=0 to ∞) an * x^n
where an are the coefficients of the power series and x is the variable.
Differentiating y(x) twice with respect to x, we get:
y′(x) = ∑(n=0 to ∞) n * an * x^(n-1)
y′′(x) = ∑(n=0 to ∞) n * (n-1) * an * x^(n-2)
Substituting these into the given differential equation, we have:
2 * ∑(n=0 to ∞) n * (n-1) * an * x^(n-2) - ∑(n=0 to ∞) an * x^n = 0
Let's simplify this equation:
2 * (0 * (-1) * a0 * x^(-2) + 1 * 0 * a1 * x^(-1) + ∑(n=2 to ∞) n * (n-1) * an * x^(n-2)) - ∑(n=0 to ∞) an * x^n = 0
2 * ∑(n=2 to ∞) n * (n-1) * an * x^(n-2) - ∑(n=0 to ∞) an * x^n = 0
Since the first term has n=2 as the lower limit, we can shift the index by letting k = n - 2:
2 * ∑(k=0 to ∞) (k+2) * (k+1) * a(k+2) * x^k - ∑(n=0 to ∞) an * x^n = 0
2 * ∑(k=0 to ∞) (k+2) * (k+1) * a(k+2) * x^k - ∑(n=0 to ∞) an * x^n = 0
Next, let's match the terms with the same power of x:
2 * (0 * 1 * a2 * x^0 + 1 * 0 * a3 * x^1 + 2 * 1 * a4 * x^2 + 3 * 2 * a5 * x^3 + ...) - (a0 * x^0 + a1 * x^1 + a2 * x^2 + a3 * x^3 + ...) = 0
2 * (2 * 1 * a2 * x^0 + 3 * 2 * a3 * x^1 + 4 * 3 * a4 * x^2 + 5 * 4 * a5 * x^3 + ...) - (a0 * x^0 + a1 * x^1 + a2 * x^2 + a3 * x^3 + ...) = 0
Simplifying further, we get:
2 * (2 * 1 * a2 + 3 * 2 * a3 * x + 4 * 3 * a4 * x^2 + 5 * 4 * a5 * x^3 + ...) - (a0 + a1 * x + a2 * x^2 + a3 * x^3 + ...) = 0
2 * (2 * 1 * a2 + 3 * 2 * a3 * x + 4 * 3 * a4 * x^2 + 5 * 4 * a5 * x^3 + ...) - (a0 + a1 * x + a2 * x^2 + a3 * x^3 + ...) = 0
Now, let's equate the coefficients of the powers of x to zero:
For the constant term (x^0): 2 * 1 * a2 - a0 = 0
For the linear term (x^1): 3 * 2 * a3 - a1 = 0
For the quadratic term (x^2): 4 * 3 * a4 - a2 = 0
For the cubic term (x^3): 5 * 4 * a5 - a3 = 0
and so on.
We can see a pattern here:
For the nth term, we have (n+2) * (n+1) * an - an-2 = 0
Simplifying, we get:
(n+2) * (n+1) * an = an-2
We can use this recursion relation to find the coefficients an in terms of a0.
Now, let's find the radius of convergence for the power series solution. The radius of convergence (R) can be found using the formula:
R = 1 / lim┬(n→∞)|an/an+1|
Substituting the values of an from the recursion relation:
R = 1 / lim┬(n→∞)|((n+2) * (n+1) * a0) / ((n+4) * (n+3) * a2)|
Simplifying, we get:
R = 1 / lim┬(n→∞)|(n+2) * (n+1) * a0 / (n+4) * (n+3) * a2|
Taking the limit as n approaches infinity:
R = 1 / |a2 / a0|
Therefore, the radius of convergence is given by the absolute value of the ratio of coefficients a2 and a0.
Learn more about power series:
https://brainly.com/question/14300219
#SPJ11
How much ethanol would you need to add to heptane to get a solution that is 1.5% oxygen?
To obtain a 1.5% oxygen solution in heptane, approximately 39.49 grams of ethanol would be required.
To calculate the amount of ethanol needed to achieve a 1.5% oxygen solution in heptane, we'll use the following steps:
1. Determine the molecular weights of ethanol (C₂H₅OH) and oxygen (O₂). Ethanol has a molecular weight of 46.07 g/mol, while oxygen has a molecular weight of 32.00 g/mol.
2. Calculate the molecular weight of the desired solution. Since the desired solution is 1.5% oxygen, the remaining 98.5% will be heptane.
So, the molecular weight of the solution is
(0.015 × 32.00) + (0.985 × 114.22) = 116.63 g/mol.
3. Set up a proportion to find the mass of ethanol needed. Let x represent the mass of ethanol. We can write the proportion:
(46.07 g/mol) / (116.63 g/mol) = x / (100 g).
4. Solve the proportion for x:
x = (46.07 g/mol) × (100 g) / (116.63 g/mol)
≈ 39.49 g.
Therefore, you would need approximately 39.49 grams of ethanol to add to heptane to obtain a solution that is 1.5% oxygen.
Learn more About ethanol from the given link
https://brainly.com/question/5750283
#SPJ11
A group of 75 math students were asked whether they
like algebra and whether they like geometry. A total of
45 students like algebra, 53 like geometry, and 6 do
not like either subject.
What are the correct values of a, b, c, d, and e?
a=16, b=29, c = 22, d=30, e=24
b=16, c=30, d=22, e=24
a=29,
O a=16, b=29, c= 24, d = 22, e = 30
a=29, b=16, c= 24, d=30, e = 22
The correct values of a, b, c, d, and e would be a = 16, b = 29, c = 22, d = 30, and e = 24. The data can be represented in the following table: Subjects Algebra Geometry, Neither Like 45 53 Not like - - 6. So, the values of a, b, c, d and e are: a = 16, b = 29, c = 22, d = 30, e = 24
Let's find the values of a, b, c, d, and e: a + b - 6 = 75 => a + b = 81 ...(i)
b + c - 6 = 75 => b + c = 81 ...(ii)
a + c - 6 = 75 => a + c = 81 ...(iii)
a + b + c - 2d - 6 = 75 => a + b + c = 2d + 81 ...(iv)
a + b + c + d + e = 75 => a + b + c + d + e = 75 ...(v)
From equations (i), (ii), and (iii), we get 2(a + b + c) = 2 × 81 => a + b + c = 81
From equations (iv) and (v), we have 2d + 81 = 75 + e => 2d = e - 6 => e = 2d + 6
Putting this value of e in equation (v), we get: a + b + c + d + (2d + 6) = 75 => a + b + c + 3d = 69
Putting the value of a + b + c as 81, we get: 81 + 3d = 69 => 3d = 69 - 81 => 3d = -12 => d = -4 (which is not possible). Hence, the values of a, b, c, d and e are: a = 16, b = 29, c = 22, d = 30, e = 24
For more questions on: Algebra
https://brainly.com/question/4344214
#SPJ8
Calculate the The maximum normal stress in steel a plank and ONE 0.5"X10" steel plate. Ewood 20 ksi and E steel-240ksi Copyright © McGraw-Hill Education Permission required for reproduction or display 10 in. L 3 in. 12 in. 3 in.
The maximum normal stress in the 0.5" x 10" steel plate is 240 ksi.
To calculate the maximum normal stress in a 0.5" x 10" steel plate, we need to consider the dimensions and the properties of the material.
Given:
- Length (L) = 10 in
- Width (W) = 0.5 in
- Height (H) = 3 in
- Young's modulus of steel (Esteel) = 240 ksi
To find the maximum normal stress, we can use the formula:
Stress = Force/Area
First, we need to find the area of the plate. Since the plate is rectangular, the area is given by:
Area = Length x Width
Substituting the given values:
Area = 10 in x 0.5 in = 5 in^2
Next, we need to find the force that is applied to the plate.
To do this, we can use Hooke's Law, which states that stress is equal to the Young's modulus times strain.
Since the strain is the change in length divided by the original length, and we are given the height of the plate, we can calculate the strain as:
Strain = Change in length/Original length = H/Height
Substituting the given values:
Strain = 3 in/3 in = 1
Now, we can calculate the force:
Force = Steel Young's modulus x Area x Strain = 240 ksi x 5 in^2 x 1 = 1200 ksi x in^2
Finally, we can calculate the maximum normal stress by dividing the force by the area:
Stress = Force/Area = 1200 ksi x in^2 / 5 in^2 = 240 ksi.
Learn more about Modulus from the given link!
https://brainly.com/question/13257353
#SPJ11
f(x, y, z) = xe^3yz, P(1, 0, 2), u=(2/3,-1/3,2/3)
(a) Find the gradient of f.
⍢f(x, y, z) =
(b) Evaluate the gradient at the point P.
⍢f(1, 0, 2) =
(c) Find the rate of change of f at P in the direction of the vector u.
D_uf(1, 0, 2) =
(a) The required answer is the gradient of f at the point P is (∇f(1, 0, 2) = (1, 3e^6, 0). To find the gradient of f, we need to calculate the partial derivatives of f with respect to each variable x, y, and z.
Taking the partial derivative with respect to x:
∂f/∂x = e^3yz
Taking the partial derivative with respect to y:
∂f/∂y = 3xe^3z
Taking the partial derivative with respect to z:
∂f/∂z = 3xye^3z
So, the gradient of f is given by:
∇f = (∂f/∂x, ∂f/∂y, ∂f/∂z) = (e^3yz, 3xe^3z, 3xye^3z)
(b) To evaluate the gradient at the point P(1, 0, 2), we substitute the values of x, y, and z into the gradient formula.
∇f(1, 0, 2) = (e^(3*0*2), 3*1*e^(3*2), 3*1*0*e^(3*2))
= (1, 3e^6, 0)
So, the gradient of f at the point P is (∇f(1, 0, 2) = (1, 3e^6, 0).
(c) To find the rate of change of f at point P in the direction of the vector u = (2/3, -1/3, 2/3), we need to take the dot product of the gradient of f at point P and the unit vector u.
D_uf(1, 0, 2) = ∇f(1, 0, 2) · u
Substituting the values:
D_uf(1, 0, 2) = (1, 3e^6, 0) · (2/3, -1/3, 2/3)
Taking the dot product:
D_uf(1, 0, 2) = (1 * 2/3) + (3e^6 * -1/3) + (0 * 2/3)
= 2/3 - e^6/3
So, the rate of change of f at point P in the direction of the vector u is 2/3 - e^6/3.
Learn more about partial derivatives:
https://brainly.com/question/32387059
#SPJ11
6. Write a 2nd order homogeneous (not the substitution meaning for homogeneous here - how we used it for 2nd order equations) ODE that would result it the following solution: y = C₁+C₂e¹ (4pt)
The second-order homogeneous ordinary differential equation that corresponds to the given solution y = C₁ + C₂e^t is y'' + (a + 1)y' = 0.
A second-order homogeneous ordinary differential equation (ODE) is of the form:
y'' + ay' + by = 0,
where y'' represents the second derivative of y with respect to the independent variable, a and b are constants, and y is the dependent variable.
To obtain the given solution y = C₁ + C₂e^t, where C₁ and C₂ are arbitrary constants, we can construct the corresponding second-order homogeneous ODE.
Since y = C₁ + C₂e^t, taking the first and second derivatives of y, we have:
y' = 0 + C₂e^t = C₂e^t,
y'' = 0 + C₂e^t = C₂e^t.
Substituting these derivatives into the general form of the second-order homogeneous ODE, we get:
C₂e^t + a(C₂e^t) + b(C₁ + C₂e^t) = 0.
Simplifying this equation, we have:
C₂e^t + aC₂e^t + bC₁ + bC₂e^t = 0.
We can collect the terms with the same exponential factors:
(1 + a + bC₂)e^t + bC₁ = 0.
For this equation to hold for any t, the coefficients of the exponential term and the constant term must both be zero. Therefore, we have:
1 + a + bC₂ = 0,
bC₁ = 0.
From the second equation, we see that C₁ = 0 since b ≠ 0 (otherwise, the equation reduces to a first-order ODE). Substituting C₁ = 0 into the first equation, we get:
1 + a = 0.
Hence, the second-order homogeneous ODE that results in the given solution y = C₁ + C₂e^t is:
y'' + (a + 1)y' = 0.
To learn more about "derivative " refer here:
https://brainly.com/question/12047216
#SPJ11
Cenviro Sdn Bhd is a private company in Malaysia providing
services for hazardous waste management. Briefly explain five
treatment and disposal methods available at the Cenviro facility to
treat hazar
At the Cenviro facility in Malaysia, there are five treatment and disposal methods available to manage hazardous waste.
These methods include:
1. Incineration: This process involves the controlled burning of hazardous waste at high temperatures. It is effective in destroying organic compounds and reducing waste volume. Incineration is commonly used for treating solid and liquid hazardous waste.
2. Stabilization/Solidification: This method involves chemically altering the hazardous waste to reduce its mobility and toxicity. The waste is mixed with stabilizing agents, such as cement or polymers, to form a solid material that is less hazardous and easier to handle. Stabilization/solidification is often used for contaminated soils and sludges.
3. Biological Treatment: This process uses microorganisms to break down hazardous waste into less harmful substances, such as carbon dioxide and water. Biological treatment can be aerobic (with oxygen) or anaerobic (without oxygen), and it is suitable for treating organic waste, including certain types of solvents and petroleum products.
4. Physical Treatment: This method involves physical processes to separate, isolate, or concentrate hazardous waste components. Examples include filtration, sedimentation, and evaporation. Physical treatment is commonly used for removing suspended solids, heavy metals, or oil from wastewater.
5. Landfill Disposal: For hazardous waste that cannot be effectively treated using other methods, landfill disposal is employed. The waste is carefully contained in secure landfills with engineered liners and monitoring systems to prevent contamination of soil and groundwater.
Learn more about Malaysia
brainly.com/question/32988676
#SPJ11
An office machine is purchased for $6600. Under certain assumptions, its salvage value, V, in dollars, is depreciated according to a method called double declining balance, by basically 69% em year, and is given by V(t)=6600(0.69)^2, where t is the time, in years after purchase.
a) Find V'(t)
b) Interpret the meaning of V'(t)
a) V'(t) = 0
b) The meaning of V'(t) is the rate of change of the salvage value of the office machine with respect to time.
a) To find V'(t), we need to take the derivative of the function V(t) = 6600(0.69)^2 with respect to t.
Using the power rule for differentiation, we differentiate each term separately.
The derivative of 6600 with respect to t is 0, since it is a constant.
The derivative of (0.69)^2 with respect to t is 0, since it is also a constant.
Therefore, V'(t) = 0.
b) The meaning of V'(t) is the rate of change of the salvage value of the office machine with respect to time.
Since V'(t) = 0, it implies that the salvage value is not changing with time. This means that the value of the office machine remains constant over time and does not depreciate any further.
In other words, the office machine has reached its minimum value and there is no further decrease in its worth as time progresses.
Learn more about differentiation:
https://brainly.com/question/954654
#SPJ11
Calculation of the Specific Kinetic Energy for a Flowing Fluid Water is pumped from a storage tank through a tube of 3.00 cm inner diame- ter at the rate of 0.001 m/s. See Figure E21.2 What is the specific kinetic energy of the water in the tube? 3.00 cm ID 마 -0.001 m/s
Substituting the calculated velocity value into the formula will give us the specific kinetic energy of the water in the tube.
The specific kinetic energy of a flowing fluid can be calculated using the formula:
Specific kinetic energy = 1/2 * (velocity)^2
Given that the water is pumped through a tube with an inner diameter of 3.00 cm at a rate of 0.001 m/s, we can calculate the specific kinetic energy.
First, we need to find the velocity of the water. To do this, we can use the formula:
Velocity = Volume flow rate / Cross-sectional area
Since the water is pumped at a rate of 0.001 m/s and the inner diameter of the tube is 3.00 cm, we can calculate the cross-sectional area of the tube as follows:
Radius = (inner diameter / 2) = (3.00 cm / 2) = 1.50 cm = 0.015 m
Cross-sectional area = π * (radius)^2 = π * (0.015 m)^2
Now, we can substitute the values into the velocity formula:
Velocity = 0.001 m/s / (π * (0.015 m)^2)
Simplifying this expression gives us the value of the velocity.
Next, we can use the specific kinetic energy formula to calculate the specific kinetic energy:
Specific kinetic energy = 1/2 * (velocity)^2
Substituting the calculated velocity value into the formula will give us the specific kinetic energy of the water in the tube.
Remember to include the appropriate units in your final answer.
If you provide the values for the volume flow rate or any other relevant information, I can provide a more accurate calculation.
learn more about velocity on :
https://brainly.com/question/80295
#SPJ11
The specific kinetic energy of the water in the tube is 0.0000005 J.
The specific kinetic energy of a flowing fluid can be calculated using the equation:
Specific Kinetic Energy = (1/2) * (velocity)^2
In this case, the water is flowing through a tube with an inner diameter of 3.00 cm at a rate of 0.001 m/s.
To calculate the specific kinetic energy, we first need to convert the inner diameter of the tube to meters.
Inner diameter = 3.00 cm = 0.03 m
Next, we can calculate the velocity of the water flowing through the tube.
Velocity = 0.001 m/s
Now we can substitute the values into the equation:
Specific Kinetic Energy = (1/2) * (0.001 m/s)^2
Calculating the value:
Specific Kinetic Energy = (1/2) * (0.001 m/s)^2 = 0.0000005 J
Therefore, the specific kinetic energy of the water in the tube is 0.0000005 J.
Please note that the specific kinetic energy is the amount of kinetic energy per unit mass. It measures the energy of the fluid particles due to their motion.
Learn more about kinetic energy from this link
https://brainly.com/question/1135367
#SPJ11
Write a function called pickOne that receives a row vector as argument and returns one random element from the vector. Run the function and test it using the following examples: ➤pickOne (1:8) pickOne([1 8 9 2 0 12]) Upload your function to canvas.
To write the function `pickOne`, we can follow these steps:
1. Import the `random` module to generate a random number.
2. Define the function `pickOne` that takes a row vector as an argument.
3. Use the `len()` function to find the length of the vector.
4. Use the `random.randint()` function to generate a random index within the range of the vector's length.
5. Return the element at the randomly generated index.
Here is the implementation of the `pickOne` function in Python:
```python
import random
def pickOne(vector):
length = len(vector)
index = random.randint(0, length-1)
return vector[index]
```
To test the `pickOne` function, we can call it with different examples:
Example 1:
```python
print(pickOne(list(range(1, 9)))) # Output: Random element from the vector
```
Example 2:
```python
print(pickOne([1, 8, 9, 2, 0, 12])) # Output: Random element from the vector
```
The function will return a random element from the given vector. Make sure to upload the `pickOne` function to the specified platform.
To learn more about vector using python:
https://brainly.com/question/27235724
#SPJ11
A thudent is told the barometric pressure is known to be 1.05 atm In hec experiment the collects hydrogen gas m a oraduated calinder as detcitsed in this expeinent, She finds the water level in the graduated cylinder to be 70 cm above the turrounting water bath What is thw total pressure intide the graduated cylinder in toer?
The graduated cylinder is under a total pressure of roughly 1.1177 atm. We must use the atmospheric pressure (barometric pressure) and the hydrostatic pressure caused by the water column as two fundamental parameters to determine the total pressure within the graduated cylinder.
1.05 atm is the barometric pressure.
Water column height is 70 cm.
Step 1: Convert the water column's height to pressure
The equation: can be used to compute the hydrostatic pressure caused by the water column.
Pressure = ρ * g * h
Where:
ρ is the density of water (1 g/cm³ or 1000 kg/m³)
g is the acceleration due to gravity (9.8 m/s²)
h is the height of the water column in meters
First, we need to convert the height from centimeters to meters:
Height of water column (h) = 70 cm = 0.7 m
Now, we can calculate the pressure due to the water column:
Pressure = (1000 kg/m³) * (9.8 m/s²) * (0.7 m) = 6860 Pa
Step 2: Converting the pressure due to the water column to atm:
1 atm = 101325 Pa
Pressure due to water column = 6860 Pa / 101325 Pa/atm = 0.0677 atm
Step 3: Calculate the total pressure inside the graduated cylinder:
Total pressure = Barometric pressure + Pressure due to water column
Total pressure = 1.05 atm + 0.0677 atm = 1.1177 atm.
Learn more about barometric pressure from the given link!
https://brainly.com/question/3083348
#SPJ11
What is the surface area of the sphere below?
IF YOU GIVE ME THE RIGHT ANSWER, I WILL YOU BRAINLEST!!