To turn liquid copper of mass 1.5 kg at 1083 degrees Celsius to solid copper at 1000 degrees Celsius, approximately -2.49×10^5 J of energy must be removed from the system. For the concrete brick wall, the temperature outside is approximately 5.67 degrees Celsius.
When a substance undergoes a phase change, energy needs to be removed or added to the system to facilitate the transition. In the case of turning liquid copper to solid copper, we need to calculate the energy that must be removed. The amount of energy can be calculated using the equation:
Q = mcΔT,
where Q represents the energy, m is the mass of the substance, c is the specific heat capacity, and ΔT is the change in temperature. Since copper has a specific heat capacity of approximately 390 J/kg·°C, we can calculate the energy required as follows:
Q = (1.5 kg) × 390 J/kg·°C × (1083 °C - 1000 °C) = -2.49×10^5 J.
Hence, approximately -2.49×10^5 J of energy must be removed from the system to turn liquid copper at 1083 degrees Celsius to solid copper at 1000 degrees Celsius.
For the concrete brick wall, the rate of energy transfer through the wall is given as 160 W. We can use the formula:
P = kA(ΔT/Δx),
where P is the power, k is the thermal conductivity of the material, A is the area, ΔT is the temperature difference, and Δx is the thickness. Rearranging the equation, we have:
ΔT = (PΔx)/(kA).
Plugging in the values, where the thickness (Δx) is 6 cm (or 0.06 m), the height (A) is 3 m × 6 m = 18 m², the power (P) is 160 W, and the thermal conductivity of concrete is approximately 1.7 W/(m·°C), we can calculate the temperature difference:
ΔT = (160 W × 0.06 m)/(1.7 W/(m·°C) × 18 m²) ≈ 5.67 °C.
Therefore, the temperature outside is approximately 5.67 degrees Celsius.
Learn more about energy transfer here:
https://brainly.com/question/13087586
#SPJ11
An the light emitted from electronic transition in a H atom for a transition from n = 3 to n = 2 has a characteristic wavelength range of 656 nm. Calculate the following: The frequency of the light em
Therefore, the frequency of the light emitted from this electronic transition is approximately 4.58 × 10^14 s^-1 (or hertz).
Electronic transition in a hydrogen atom for a transition from n = 3 to n = 2 has a characteristic wavelength range of 656 nm. To calculate the frequency of the light emitted, we can use the following equation: c = λν,where c is the speed of light, λ is the wavelength, and ν is the frequency. We are given the wavelength, so we can solve for the frequency:ν = c/λ = (3.00 × 10^8 m/s)/(656 nm × 10^-9 m/nm) ≈ 4.58 × 10^14 s^-1. Therefore, the frequency of the light emitted from this electronic transition is approximately 4.58 × 10^14 s^-1 (or hertz).
To know more about electron visit:
https://brainly.com/question/14904694
#SPJ11
Hydroelectric generators at Hoover Dam produce a maximum current of 8.05 x 10³ A at 251 kV. a) What is the power output? ___________________ W b) The water that powers the generators enters and leaves the system at low speed (thus its kinetic energy does not change) but loses 155 m in altitude. How many cubic meters per second are needed, assuming 86 % efficiency? __________ m³/s
The power output Hydroelectric generators at Hoover Dam produce a maximum current of 8.05 x 10³ A at 251 kV is 2.022 x 10⁹W. Cubic meters per second needed by assuming 86 % efficiency is 1547.83 m³/s.
a) The formula to calculate the power output is,
Power (P) = Current (I) x Voltage (V)
It is given that, Current (I) = 8.05 x 10³ A and Voltage (V)= 251 kV= 251,000 V
Substituting these values into the formula:
Power = (8.05 x 10³ A) x (251,000 V)
Power = 2.022 x 10⁹ W
Therefore, the power output is 2.022 x 10⁹ watts.
b) To calculate the flow rate of water needed, we can use the formula:
Power (P) = Efficiency (η) x Density (ρ) x Acceleration due to gravity (g) x Flow rate (Q) x Height (h)
It is given that, Power (P) = 2.022 x 10⁹ W, Efficiency (η) = 0.86 (86% efficiency), Density of water (ρ) = 1000 kg/m³, Acceleration due to gravity (g) = 9.8 m/s², Height (h) = 155 m
Substituting these values into the formula:
2.022 x 10⁹ W = 0.86 x (1000 kg/m³) x (9.8 m/s²) x Q x 155 m
Simplifying the equation:
Q= (2.022 x 10⁹ W) / (0.86 x 1000 kg/m³ x 9.8 m/s² x 155 m)
Q=1547.83 m³/s
Therefore, 1547.83 cubic meters per second of water are needed, assuming 86% efficiency.
To learn more about power: https://brainly.com/question/11569624
#SPJ11
After a bomb at rest explodes into two unequal fragments, the more massive fragment has the same kinetic energy as the less massive fragment. more kinetic energy than the less massive fragment. less kinetic energy than the less massive fragment.
When a bomb at rest explodes into two unequal fragments, the more massive fragment has less kinetic energy than the less massive fragment.
According to the law of conservation of momentum, the total momentum before and after the explosion must be the same. In this case, since the bomb is initially at rest, the total momentum before the explosion is zero. After the explosion, the two fragments move in opposite directions, but their combined momentum must still add up to zero.
Since momentum is the product of mass and velocity, if one fragment has a greater mass, it must have a lower velocity to maintain the total momentum at zero. As kinetic energy is proportional to the square of velocity, the more massive fragment will have a lower kinetic energy compared to the less massive fragment.
This phenomenon can be explained by the conservation of energy. The initial energy of the bomb is stored in the form of chemical potential energy. When the bomb explodes, this energy is converted into the kinetic energy of the fragments. However, due to the unequal masses, the less massive fragment receives a greater share of the initial energy, resulting in a higher kinetic energy.
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
09) Write the normal force acting on the skier if the friction is neglected. Skier mass=m gravity
The Normal force acting on the skier if the friction is neglected is mg.
The normal force acting on the skier if the friction is neglected is equal to the weight of the skier which is mg, where m is the mass of the skier and g is the acceleration due to gravity. This is because according to Newton's laws of motion, an object at rest or in uniform motion in a straight line will remain in that state of motion unless acted upon by a net force.
Since there is no net force acting on the skier in the vertical direction, the normal force is equal to the weight of the skier.Steps to find the normal force:
Step 1: Write down the given information. Skier mass = m Gravity = g.
Step 2: Determine the weight of the skier Weight = mg.
Step 3: The normal force is equal to the weight of the skier. Normal force = weight = mg.
Therefore, the normal force acting on the skier if the friction is neglected is mg.
Learn more about normal force : https://brainly.com/question/28788588
#SPJ11
Newton's 2nd law of motion is only valid in inertial frame of reference. (i) Define what is meant by inertial frame of reference. (5 marks) (ii) Consider a reference frame that rotates at uniform angular velocity, but moves in constant motion with respect to a inertial frame. Write down the equation of motion of a particle mass m that moves with velocity with respect to rotating frame. Explain all the force terms involved in the Newton's law of motion for this case. (15 marks) 5/8 SIF2004 (iii) Consider a bucket of water set to spin about its symmetry axis at uniform w. the most form of effective as determined in (i), show that at equilibrium, the surface of the water in the bucket takes the shape of a parabola. State all assumptions and to approximations.
(i) An inertial frame of reference is a non-accelerating frame where Newton's laws of motion hold true.
(ii) In a rotating frame, the equation of motion includes the inertial force, Coriolis force, and centrifugal force, affecting the motion of a particle.
(i) Inertial Frame of Reference:
An inertial frame of reference is a frame in which Newton's laws of motion hold true, and an object at rest or moving in a straight line with constant velocity experiences no net force. In other words, an inertial frame of reference is a non-accelerating frame or a frame moving with a constant velocity.
(ii) Equation of Motion in a Rotating Frame:
In a reference frame that rotates at a uniform angular velocity but moves with constant velocity with respect to an inertial frame, the equation of motion for a particle of mass m moving with velocity [tex]\(\mathbf{v}\)[/tex]with respect to the rotating frame can be written as:
[tex]\[ m \left(\frac{d\mathbf{v}}{dt}\right)_{\text{rot}} = \mathbf{F}_{\text{inertial}} + \mathbf{F}_{\text{cor}} + \mathbf{F}_{\text{cent}} \][/tex]
where:
- [tex]\(\left(\frac{d\mathbf{v}}{dt}\right)_{\text{rot}}\)[/tex] is the rate of change of velocity of the particle with respect to the rotating frame.
- [tex]\(\mathbf{F}_{\text{inertial}}\)[/tex] is the force acting on the particle in the inertial frame.
- [tex]\(\mathbf{F}_{\text{cor}}\)[/tex] is the Coriolis force, which arises due to the rotation of the frame and acts perpendicular to the velocity of the particle.
- [tex]\(\mathbf{F}_{\text{cent}}\)[/tex]is the centrifugal force, which also arises due to the rotation of the frame and acts radially outward from the center of rotation.
The Coriolis force and the centrifugal force are additional apparent forces that appear in the equation of motion in a rotating frame.
(iii) Surface Shape of Water in a Spinning Bucket:
When a bucket of water spins about its symmetry axis at a uniform angular velocity, assuming the bucket is rotating in an inertial frame, the surface of the water in the bucket takes the shape of a parabola. This occurs due to the balance between gravity and the centrifugal force acting on the water particles.
Assumptions and Approximations:
- The bucket is assumed to be rotating at a constant angular velocity.
- The water is assumed to be in equilibrium, with no net acceleration.
- The surface of the water is assumed to be smooth and not affected by other external forces.
- The effects of surface tension and air resistance are neglected.
Under these assumptions, the shape of the water's surface conforms to a parabolic curve, as the centrifugal force counteracts the force of gravity, causing the water to rise higher at the edges and form a concave shape in the center.
Learn more about centrifugal force here:
https://brainly.com/question/545816
#SPJ11
Consider the continuous-time signal x₂ (t) = cos [ 27 (500)t] which is sampled at fs = 400 samples/sec. a) Find an expression for the resulting discrete-time signal x[n] = x₂ (nT), T: f. b) Find a discrete-time sinusoidal signal y[n] = cos(N₂n), -r≤ ≤, which yields the same sample values as x[n] in part a). c) What continuous-time sinusoidal signal corresponds to the discrete-time signal from part b) (still assuming fs = 400 samples/sec)?
a) To find the expression for the resulting discrete-time signal x[n] = x₂(nT), where T = 1/fs is the sampling period and fs = 400 samples/sec is the sampling frequency, we substitute n = t/T into the continuous-time signal x₂(t):
x[n] = x₂(nT) = cos[27(500)(nT)]
= cos[27(500)(n/fs)]
Since fs = 400 samples/sec, the expression becomes:
x[n] = cos[27(500)(n/400)]
b) Now we need to find a discrete-time sinusoidal signal y[n] = cos(N₂n) that yields the same sample values as x[n] from part a).
Comparing the expressions, we have:
N₂ = 27(500)/fs
N₂ = 27(500)/400
N₂ = 33.75
So, the discrete-time sinusoidal signal y[n] is given by:
y[n] = cos(33.75n)
c) To find the continuous-time sinusoidal signal corresponding to the discrete-time signal y[n] from part b), we need to convert it back to continuous time using the same sampling frequency fs = 400 samples/sec.
Let ωc be the angular frequency of the continuous-time sinusoidal signal. We know that ωc = 2πfc, where fc is the continuous-time frequency. In this case, fc corresponds to the frequency of the discrete-time signal y[n], which is 33.75 cycles/sample.
We can calculate the continuous-time frequency as:
fc = 33.75 × fs
= 33.75 × 400
= 13500 Hz
Therefore, the continuous-time sinusoidal signal corresponding to the discrete-time signal y[n] is:
x₃(t) = cos(2π(13500)t)
#SPJ11
Learn more about continuous-time and discrete-time signal: https://brainly.in/question/10732752
A bead is constrained to move without friction on a curved wire. The curve lies in the horizontal plane, so you can ignore the effect of gravity. The horizontal plane is the XY plane, and the curve is given by y = f(x). The bead moves with a speed v on the wire. Answer the following questions: ac (a) The only force acting on the bead is the force of constraint from the wire. Why is the speed of the bead constant? (b) Express i and ï in terms of v and derivatives of f with respect to r. Use j, f, etc to denote time derivatives of f(x), and f', f", etc to denote on SL, etc. (c) Find the x component of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to x. (d) Find the y component of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to x. (e) Find the magnitude of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to z. Show that if the curve is a circle, the magnitude of the force mv2 reduces to the expected expression of R
(a)The bead is constrained to move without friction on a curved wire. (b)Thus, i = v/f' and j = -v f"/(1 + f'2)3/2. (c)The force of the wire on the bead is always perpendicular to the curve. (d)The y component of the force of the wire on the bead is Fy = mv2 f"/(1 + f'2)3/2. (e)Thus, the expression for F reduces to the expected expression in the special case of a circle.
(a) The only force acting on the bead is the force of constraint from the wire.
The bead is constrained to move without friction on a curved wire. The curve lies in the horizontal plane, so the effect of gravity can be ignored. Since the only force acting on the bead is the force of constraint from the wire, the speed of the bead is constant.
(b) Express i and j in terms of v and derivatives of f with respect to r. Use f, f', f", etc to denote derivatives of f(x) with respect to x.
The unit vector i is tangent to the curve and j is normal to the curve. Thus, i = v/f' and j = -v f"/(1 + f'2)3/2.
(c) Find the x component of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to x.
The x component of the force of the wire on the bead is zero.
The force of the wire on the bead is always perpendicular to the curve.
(d) Find the y component of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to x.
The y component of the force of the wire on the bead is Fy = mv2 f"/(1 + f'2)3/2.
(e) Find the magnitude of the force of the wire on the bead, in terms of m, v, and derivatives of f with respect to z.
Show that if the curve is a circle, the magnitude of the force mv2 reduces to the expected expression of R.
The magnitude of the force of the wire on the bead is given by F = mv2 / (1 + f'2)3/2. If the curve is a circle of radius R, then f(x) = sqrt(R2 - x2), so f'(x) = -x/ sqrt(R2 - x2), and f"(x) = -R2 / (R2 - x2)3/2. Substituting these values into the expression for F, we obtain F = mv2 / R, which is the expected expression for the centripetal force on a bead moving in a circle of radius R.
Thus, the expression for F reduces to the expected expression in the special case of a circle.
Learn more about force here:
https://brainly.com/question/30507236
#SPJ11
ball is thrown horizontally from a 17 m-high building with a speed of 9.0 m/s. How far from the base of the building does the ball hit the ground?
When a ball is thrown horizontally from a 17 m-high building with a speed of 9.0 m/s, it will hit the ground approximately 4.3 meters away from the base of the building.
When the ball is thrown horizontally, its initial vertical velocity is 0 m/s since there is no vertical component to the throw. The only force acting on the ball in the vertical direction is gravity, which causes it to accelerate downward at a rate of 9.8 m/s². Since the initial vertical velocity is 0, the time it takes for the ball to reach the ground can be calculated using the equation d = 0.5 * a * t², where d is the vertical distance traveled, a is the acceleration due to gravity, and t is the time. In this case, the vertical distance traveled is 17 meters. Rearranging the equation to solve for time, we get t = sqrt(2d/a). Substituting the values, we find t = sqrt(2 * 17 / 9.8) ≈ 2.15 seconds. Since the horizontal velocity remains constant throughout the motion, the distance the ball travels horizontally can be calculated using the equation d = v * t, where v is the horizontal velocity and t is the time. Substituting the values, we get d = 9.0 * 2.15 ≈ 19.4 meters. Therefore, the ball hits the ground approximately 4.3 meters away from the base of the building.
Learn more about free fall:
https://brainly.com/question/13796105
#SPJ11
A marble rolls off a horizontal tabletop that is 0.97 m high and hits the floor at a point that is a horizontal distance of 3.64 m from the edge of the table.
a) How much time, in seconds, was the marble in the air?
b) what is the speed of the marble as it rolled off the table?
c) what was the marble's speed just before hitting the floor?
a) The marble was in the air for approximately 0.64 seconds.
b) The speed of the marble as it rolled off the table was 4.81 m/s.
c) The marble's speed just before hitting the floor was 8.69 m/s.
a) To determine the time the marble was in the air, we can use the equation h = 0.5 * g * t^2, where h is the height, g is the acceleration due to gravity (approximately 9.8 m/s^2), and t is the time. Rearranging the equation, we get t = sqrt(2h / g). Substituting the given values, t = sqrt(2 * 0.97 m / 9.8 m/s^2) ≈ 0.64 s.
b) The speed of the marble as it rolled off the table can be found using the equation v = sqrt(2gh), where v is the velocity, g is the acceleration due to gravity, and h is the height. Substituting the given values, v = sqrt(2 * 9.8 m/s^2 * 0.97 m) ≈ 4.81 m/s.
c) To calculate the marble's speed just before hitting the floor, we can use the equation v = sqrt(v0^2 + 2g * d), where v is the final velocity, v0 is the initial velocity (which is the speed as it rolled off the table), g is the acceleration due to gravity, and d is the horizontal distance traveled. Substituting the given values, v = sqrt((4.81 m/s)^2 + 2 * 9.8 m/s^2 * 3.64 m) ≈ 8.69 m/s.
Learn more about acceleration due to gravity here:
https://brainly.com/question/14550373
#SPJ11
An electromagnetic wave travels in -z direction, which is -ck. What is/are the possible direction of its electric field, E, and magnetic field, B, at any moment? Electric field Magnetic field A. +Ei +Bj B. +Ej +Bi C. -Et +Bj
An electromagnetic wave travels in -z direction, which is -ck is the possible direction of its electric field, E, and magnetic field, B, at any moment. Therefore, options A, B, and C are all possible directions of the electric field and magnetic field of an electromagnetic wave.
An electromagnetic wave has two perpendicular fields that oscillate sinusoidally, one of which is electric and the other magnetic.
They are at right angles to one other and to the direction of the wave's movement. The magnetic field is always perpendicular to the electric field and the direction of wave propagation.
The electric field oscillates in the plane of the electric field and the direction of wave propagation. The magnetic field oscillates in the plane of the magnetic field and the direction of wave propagation.
The wave's direction of motion is in the -z direction. We may describe the electric field and the magnetic field with the help of these directions.
A. +Ei +Bj In the positive x direction, the electric field is perpendicular to the z direction. Since the electric field is oscillating in the plane of the magnetic field and the direction of wave propagation, it will have both i and j components.
The magnetic field is in the positive y direction and is perpendicular to the electric field and the direction of wave propagation. It is therefore represented by Bj. B. +Ej +Bi . In the positive y direction, the electric field is perpendicular to the z direction.
Since the electric field is oscillating in the plane of the magnetic field and the direction of wave propagation, it will have both i and j components. The magnetic field is in the positive x direction and is perpendicular to the electric field and the direction of wave propagation.
It is therefore represented by Bi.C. -Et +BjIn the negative x direction, the electric field is perpendicular to the z direction.
Since the electric field is oscillating in the plane of the magnetic field and the direction of wave propagation, it will have both i and j components. The magnetic field is in the positive y direction and is perpendicular to the electric field and the direction of wave propagation. It is therefore represented by Bj.
Therefore, options A, B, and C are all possible directions of the electric field and magnetic field of an electromagnetic wave.
Learn more about electromagnetic wave here:
https://brainly.com/question/29774932
#SPJ11
Buck - Boost converter system parameters: Vg=48V input voltage, output voltage Vo=12V, output load R=1~100Ω, output filter inductance L=100μH, capacitance C=220μF, switch frequency fsw=40kHz, namely switch cycle Tsw=25μs. PWM modulator sawtooth amplitude VM=2.5V. Feedback current network transfer function Hi(s)=1 feedback partial voltage network transfer function Hv(s)=0.5
Draw the circuit and give Detailed derivation of the transfer function.
The Buck-Boost converter system consists of an input voltage of 48V, an output voltage of 12V, and various parameters such as load resistance, filter inductance, capacitance, switch frequency, and PWM modulator sawtooth amplitude. The feedback current network transfer function is given as Hi(s) = 1, and the feedback partial voltage network transfer function is Hv(s) = 0.5. The circuit diagram and transfer function derivation will be explained in detail.
The Buck-Boost converter is a DC-DC power converter that can step up or step down the input voltage to achieve the desired output voltage. Here is a step-by-step explanation of the circuit and the derivation of the transfer function:
1. Circuit Diagram: The circuit consists of an input voltage source (Vg), an inductor (L), a switch (S), a diode (D), a capacitor (C), and the load resistance (R). The PWM modulator generates a sawtooth waveform (VM) used for switching control.
2. Operation: During the switch ON period, energy is stored in the inductor. During the switch OFF period, the stored energy is transferred to the output.
3. Transfer Function Derivation: To derive the transfer function, we analyze the circuit using small-signal linearized models and Laplace transforms.
4. Voltage Transfer Function: By applying Kirchhoff's voltage law and using the small-signal model, we can derive the voltage transfer function Vo(s)/Vg(s) as a function of the circuit components.
5. Current Transfer Function: Similarly, by analyzing the current flow in the circuit, we can derive the current transfer function Io(s)/Vg(s) as a function of the circuit components.
6. Feedback Transfer Functions: The given feedback transfer functions, Hi(s) and Hv(s), relate the feedback current and voltage to the input voltage.
7. Overall Transfer Function: The overall transfer function of the Buck-Boost converter system can be obtained by combining the voltage transfer function, current transfer function, and feedback transfer functions.
By following these steps, the detailed derivation of the transfer function for the Buck-Boost converter system can be obtained. The transfer function describes the relationship between the input voltage and the output voltage, and it helps in analyzing and designing the converter system for the desired performance.
To know more about the Buck-Boost click here:
https://brainly.com/question/30776258
#SPJ11
Determine the length of a copper wire that has a resistance of 0.282 g and a cross-sectional area of 0.000038 m2. The resistivity of copper is 1.72 × 10⁻⁸ m. From your answer with no decimal place.
Answer: The length of the copper wire is 6,045 m.
Resistivity of copper, ρ = 1.72 × 10⁻⁸ m
Resistance, R = 0.282 g
Cross-sectional area, A = 0.000038 m²
We can use the formula for resistance of a wire, R = ρL / A, where L is the length of the wire. Substituting the given values,
0.282 g = (1.72 × 10⁻⁸ m) × L / 0.000038 m²
Solving for L gives; L = 0.282 g × 0.000038 m² / (1.72 × 10⁻⁸ m)L = 6.045 × 10³ m.
Therefore, the length of the copper wire is 6,045 m.
Learn more about resistance: https://brainly.com/question/17563681
#SPJ11
A proton accelerates from rest in a uniform electric field of 610 NC At one later moment, its speed is 1.60 Mnys (nonrelativistic because is much less than the speed of light) (a) Find the acceleration of the proton
(b) Over what time interval does the proton reach this speed ?
(c) How far does it move in this time interval?
(d) What is its kinetic energy at the end of this interval?
Answer: a. The acceleration of the proton is 5.85 × 10^14 m/s2.
b. The time interval to reach the speed of 1.60 × 10^6 m/s= 2.74 × 10^-9 s.
c. The proton moves a distance of 1.38 × 10^-5 m.
d. kinetic energy at the end of the interval is 2.56 × 10^-12 J.
Electric field = 610 N/c,
Initial velocity, u = 0 m/s,
Final velocity, v = 1.6 × 106 m/s
(a) Acceleration of the proton: The force acting on the proton = qE where q is the charge of the proton.
Therefore, ma = qE where m is the mass of the proton.
The acceleration of the proton, a = qE/m.
Here, the charge of the proton, q = +1.6 × 10^-19 C, The mass of the proton, m = 1.67 × 10^-27 kg. Substituting the values in the equation, we get, a = 1.6 × 10^-19 C × 610 N/C ÷ 1.67 × 10^-27 kg. a = 5.85 × 10^14 m/s^2
(b) Time taken to reach this speed: We know that, v = u + at. Here, u = 0 m/s, v = 1.6 × 106 m/s, a = 5.85 × 1014 m/s2. Substituting the values, we get,1.6 × 106 = 0 + 5.85 × 10^14 × tt = 1.6 × 106 ÷ 5.85 × 10^14 s= 2.74 × 10^-9 s
(c) Distance travelled by the proton: The distance travelled by the proton can be calculated using the equation,v^2 = u^2 + 2asHere, u = 0 m/s, v = 1.6 × 106 m/s, a = 5.85 × 10^14 m/s2Substituting the values, we get,1.6 × 10^6 = 0 + 2 × 5.85 × 10^14 × s. Solving for s, we get, s = 1.38 × 10^-5 m.
(d) Kinetic energy of the proton: At the end of the interval, the kinetic energy of the proton, KE = (1/2)mv^2 Here, m = 1.67 × 10^-27 kg, v = 1.6 × 10^6 m/s. Substituting the values, we get, KE = (1/2) × 1.67 × 10^-27 × (1.6 × 10^6)^2JKE = 2.56 × 10^-12 J.
Therefore, the acceleration of the proton is 5.85 × 10^14 m/s2.
The time interval to reach the speed of 1.60 × 10^6 m/s is 2.74 × 10^-9 s.
The proton moves a distance of 1.38 × 10^-5 m.
kinetic energy at the end of the interval is 2.56 × 10^-12 J.
Learn more about proton : https://brainly.com/question/1481324
#SPJ11
Which One Is The Most Simplified Version Of This Boolean Expression ? Y = (A' B' + A B)' A. Y = B'A' + AB B. Y = AB' + BA' C. Y = B'+ A D. Y = B' + AB
which one is the most simplified version of this Boolean expression ?
Y = (A' B' + A B)'
A. Y = B'A' + AB
B. Y = AB' + BA'
C. Y = B'+ A
D. Y = B' + AB
The most simplified version of the Boolean expression Y = (A' B' + A B)' is: Y = A + B + A'
The correct answer is: C.
To simplify the Boolean expression Y = (A' B' + A B)', we can use De Morgan's theorem and Boolean algebra rules.
Let's simplify step by step:
Distribute the complement (') inside the parentheses:
Y = (A' B')' + (A B)'
Apply De Morgan's theorem to each term inside the parentheses:
Y = (A + B) + (A' + B')
Simplify the expression by removing the redundant terms:
Y = A + B + A'
The most simplified version of the Boolean expression Y = (A' B' + A B)' is:
Y = A + B + A'
Therefore, the correct answer is:
C. Y = A + B + A'
To know more about Boolean expression, here
brainly.com/question/29025171
#SPJ4
A certain measuring instrument can measure lengths as short as 0.000000300 m. Write this length with the appropriate prefix.
A certain measuring instrument can measure lengths as short as 0.000000300 m. The length can be written with the appropriate prefix, which is the picometer (pm).
One picometer is equivalent to 1×10−12 meter or 0.000000000001 meter (1 trillionth of a meter).
The prefix "pico-" denotes a factor of 10−12 (0.000000000001). Therefore, 0.000000300 m can be written as 300 pm. This means that the measuring instrument can measure lengths up to 300 picometers or 0.0000000003 meters in length.
In summary, a certain measuring instrument can measure lengths as short as 0.000000300 m, which is equivalent to 300 picometers (pm).
To learn more about picometer refer:-
https://brainly.com/question/13493801
#SPJ11
The length of Harry's forearm (elbow to wrist) is 25 cm and the length of his upper arm (shoulder to elbow) is 20 cm. If Harry flexes his elbow such that the distance from his wrist to his shoulder is 40 cm, find the angle of flexion of Harry's elbow.
The angle of flexion of Harry's elbow is approximately 55.1 degrees. To find the angle of flexion of Harry's elbow, we can use the law of cosines. Let's denote the angle of flexion as θ.
According to the law of cosines, we have:
c² = a² + b² - 2ab * cos(θ),
where:
c is the distance from Harry's wrist to his shoulder (40 cm),
a is the length of Harry's forearm (25 cm), and
b is the length of Harry's upper arm (20 cm).
Substituting the given values into the equation, we get:
40² = 25² + 20² - 2 * 25 * 20 * cos(θ).
Simplifying the equation further:
1600 = 625 + 400 - 1000 * cos(θ).
Combining like terms:
575 = 1000 * cos(θ).
Now, divide both sides of the equation by 1000:
cos(θ) = 575 / 1000.
Taking the inverse cosine (arccos) of both sides to find θ:
θ = arccos(575 / 1000).
Using a calculator, we find that arccos(575 / 1000) is approximately 55.1 degrees.
Therefore, the angle of flexion of Harry's elbow is approximately 55.1 degrees.
To learn more about law of cosines visit:
brainly.com/question/30766161
#SPJ11
At high noon, sunlight has an intensity of about 1.4 W/m2 (dude, that's a lot). If the Earth were moved twice as far from the sun, what would the intensity of sunlight be at high noon?
If the Earth were moved twice as far from the Sun, the intensity of sunlight at high noon would be 0.35 [tex]W/m^2[/tex].The intensity of sunlight at a given location is inversely proportional to the square of the distance from the source (assuming no other factors influencing intensity change). This relationship is known as the inverse square law.
If the Earth were moved twice as far from the Sun, the distance between the Earth and the Sun would be doubled. Let's denote the original distance as d and the new distance as 2d.
According to the inverse square law, the intensity of sunlight at the new distance would be given by
[tex]I_{new[/tex] = 1.4 [tex]W/m^2 * (d^2 / (2d)^2)[/tex]
= 1.4 [tex]W/m^2[/tex] * (1 / 4)
= 0.35 [tex]W/m^2[/tex]
Therefore, if the Earth were moved twice as far from the Sun, the intensity of sunlight at high noon would be 0.35 [tex]W/m^2[/tex].
Learn more about intensity here:
https://brainly.com/question/17583145
#SPJ11
What is the repulsive force between two pith balls that are 2.600E+0−cm apart ard have equal charges of 3.000E+1 −nC ?
The repulsive force between two pith balls that are 2.600E-0 cm apart and have equal charges of 3.000E-1 nC is approximately 4.59E-3 Newtons.
The repulsive force between two charged objects can be calculated using Coulomb's law, which states that the force is directly proportional to the product of the charges and inversely proportional to the square of the distance between them. Mathematically, it can be expressed as F = k * (q1 * q2) / r^2, where F is the force, k is the electrostatic constant (9.0E9 N·m^2/C^2), q1 and q2 are the charges of the objects, and r is the distance between them.
In this case, both pith balls have equal charges of 3.000E-1 nC (3.000E-10 C), and they are 2.600E-0 cm (2.600E-2 m) apart. Substituting these values into the Coulomb's law equation, we have F = (9.0E9 N·m^2/C^2) * [(3.000E-10 C)^2 / (2.600E-2 m)^2].
Simplifying the calculation, we find that the repulsive force between the pith balls is approximately 4.59E-3 Newtons.
Learn more about Coulomb's law equation here:
https://brainly.com/question/506926
#SPJ11
River water is collected into a large dam whose height is 65 m. How much power can be produced by an ideal hydraulic turbine if water is run through the turbine at a rate of 1500 L/s? (p= 1000 kg/m³ = 1 kg/L). [2]
The power that can be produced by an ideal hydraulic turbine if water is run through the turbine at a rate of 1500 L/s is 1.924 MW (megawatts).
The potential energy of the water in the dam is given by mgh, where m is the mass of the water, g is the acceleration due to gravity, and h is the height of the dam. The mass of the water can be determined using the density of water which is 1000 kg/m³ and the volume flow rate which is 1500 L/s, which gives m = 1500 kg/s.
The potential energy of the water is therefore given by: PE = mgh= 1500 × 9.81 × 65= 9,569,250 J/s or 9.569 MW (megawatts)
Since the hydraulic turbine is an ideal device, all the potential energy of the water can be converted to kinetic energy, and then to mechanical energy that can be used to turn a generator. The mechanical energy can be calculated using the formula KE = (1/2)mv², where v is the velocity of the water at the turbine. The velocity of the water can be determined using the formula Q = Av, where Q is the volume flow rate, A is the cross-sectional area of the turbine, and v is the velocity of the water.
Assuming the turbine has a circular cross-section, the area can be calculated using the formula A = πr², where r is the radius of the turbine.
Since the volume flow rate is given as 1500 L/s, which is equivalent to 1.5 m³/s, we have:1.5 = πr²v
The velocity of the water is therefore: v = 1.5/πr²
Substituting the value of v in the kinetic energy formula and simplifying, we obtain: KE = (1/2)mv²= (1/2)m(1.5/πr²)²= (1/2) × 1500 × (1.5/πr²)²= 2.774 W
Therefore, the power that can be produced by the hydraulic turbine is: PE = KE = 2.774 W= 2.774 × 10⁶ MW= 1.924 MW (approximately)
know more about hydraulic turbine
https://brainly.com/question/13065056
#SPJ11
The resistor in a series RCL circuit has a resistance of 90.00, while the rms voltage of the generator is 5.00 V. At resonance, what is the average power delivered to the circuit? P 2v
=
With an rms voltage of 5.00 V and a resistance of 90.00 Ω, the average power delivered to the circuit is approximately 0.278 W.
In a series RCL circuit at resonance, the reactance of the inductor and capacitor cancel each other out, resulting in a purely resistive circuit. At resonance, the impedance of the circuit is equal to the resistance.
The average power delivered to a resistor in an AC circuit can be calculated using the formula P = [tex]V_{rms} ^{2}[/tex] / R, where P is the average power, [tex]V_{rms} ^{2}[/tex] is the root mean square voltage, and R is the resistance.
Substituting the given values, we have P = [tex](5V)^{2}[/tex]/ 90.00 Ω = 0.278 W. Therefore, at resonance in the series RCL circuit, the average power delivered to the circuit is approximately 0.278 W.
Learn more about resonance here:
https://brainly.com/question/32273580
#SPJ11
A photographer uses his camera, whose lens has a 70 mm focal length, to focus on an object 1.5 m How far must the lens move to focus on this second object? away. He then wants to take a picture of an object that is 40 cm away. Express your answer to two significant figures and include the appropriate un
The lens must move approximately 0.103 meters to focus on the second object, and the distance of the image from the lens when taking a picture of an object that is 40 cm away is approximately 0.046 meters.
To determine the distance the lens must move to focus on the second object, we can use the lens formula:
1/f = 1/u + 1/v,
where f is the focal length of the lens, u is the distance of the first object from the lens (in meters), and v is the distance of the second object from the lens (in meters).
Given that the focal length of the lens is 70 mm, which is equivalent to 0.07 meters, and the distance of the first object is 1.5 meters, we can substitute these values into the formula:
1/0.07 = 1/1.5 + 1/v.
Simplifying this equation gives us:
v = 1 / (1/0.07 - 1/1.5).
Evaluating this expression, we find:
v ≈ 0.103 meters.
Therefore, the lens must move approximately 0.103 meters to focus on the second object.
For taking a picture of an object that is 40 cm away, we can use the same lens formula:
1/f = 1/u + 1/v,
where u is the distance of the object from the lens (in meters) and v is the distance of the image from the lens (also in meters).
Given that the focal length of the lens is 0.07 meters, we can substitute the values into the formula:
1/0.07 = 1/0.4 + 1/v.
Simplifying this equation gives us:
v = 1 / (1/0.07 - 1/0.4).
Evaluating this expression, we find:
v ≈ 0.046 meters.
Therefore, the distance of the image from the lens when taking a picture of an object that is 40 cm away is approximately 0.046 meters.
In summary, the lens must move approximately 0.103 meters to focus on the second object, and the distance of the image from the lens when taking a picture of an object that is 40 cm away is approximately 0.046 meters.
Learn more about focal length here:
https://brainly.com/question/31755962
#SPJ11
A charged capacitor with a capacitance of C=5.00×10 −3
F, has an initial potential of 5.00 V. The capacitor is discharged by connecting a resistance R between its terminals. The graph below shows the potential across the capacitor as a funtion of the time elapsed since the connection. C.alculate the value of R. Note that the curve passes through an intersection point. Tries 1/20 Previous Tries
The value of resistance R is 3.48 kΩ.
The capacitance of a charged capacitor is C=5.00×10−3F, and its initial voltage is 5.00V. When a resistor R is connected between its terminals, it is discharged. The potential across the capacitor versus time since the connection is plotted in the graph shown.The capacitor's voltage and current change as it charges and discharges. The voltage across the capacitor as a function of time elapsed since the connection is shown in the graph.
The voltage of the capacitor decreases exponentially and eventually approaches zero as it discharges.The capacitor discharge is given by the following equation:q = Q × e−t/RCWhere R is the resistance, C is the capacitance, t is the time elapsed, and q is the charge stored in the capacitor at time t. The voltage across the capacitor can be determined using the following formula:V = q/C = Q/C × e−t/RC.
The voltage across the capacitor is plotted in the graph, and the intersection point is located at t = 5.0ms and V = 2.5V. As a result, the charge stored on the capacitor at that moment is Q = CV = 5.00×10−3F × 2.50V = 12.5×10−3C.The value of R can now be calculated using the formula:R = t/ln(V0/V) × C = 5.0×10−3s/ln(5.00V/2.50V) × 5.00×10−3F ≈ 3.48kΩTherefore, the value of resistance R is 3.48 kΩ.
Learn more about capacitor here,
https://brainly.com/question/31329178
#SPJ11
The electric potential in a certain region is V = ax² + bx +c where a = 11 V/m², where b = −10 V/m², and c = 63 V. Determine the position where the electric field is zero.
The electric potential in a certain region is V = ax² + bx +c where a = 11 V/m², b = −10 V/m², and c = 63 V. We are supposed to find the position where the electric field is zero. Electric field is the negative of the gradient of potential, i.e.,
`E= -grad(V)`
Hence, to find where electric field is zero, we have to find the position where the gradient of potential is zero and then check whether that point is a point of minimum or maximum.
So, `E= -grad(V) = -(∂V/∂x) î`
For the given potential, `V = ax² + bx + c = 11x² - 10x + 63`
So, `E= -grad(V) = -(∂V/∂x) î = (-22x + 10) î`
Hence, electric field is zero when, `(-22x + 10) î = 0 => x = 5/11 m`
Therefore, the position where the electric field is zero is 5/11 m.
Learn more about electric fields: https://brainly.com/question/19878202\
#SPJ11
Each of the following objects gives off light, but the majority of their light is given off in a certain part of the spectrum, according to Wien's Law. What is the wavelength of this peak radiation, and what portion of the spectrum does it cover? • a star at about 30,000 K • the corona of the Sun, at about 2,000,000 K • the surface of our skin, at about 297 K • the Sun, at about 6000K HINT: Problem 3 is a straightforward application of Wien's Law. Use the temperature to compute values of lambda-max, and use the electromagnetic spectrum in your book to determine the wavelength region. Remember that 1 Angstrom = 10⁻¹⁰ meters!
According to Wien's Law, the star at about 30,000 K emits peak radiation at a wavelength of 96.6 nm, corresponding to the ultraviolet portion of the spectrum. Similarly, the corona of the Sun, with a temperature of about 2,000,000 K, emits peak radiation at 1.45 nm in the extreme ultraviolet region.
Wien's law is a relationship that connects the temperature of an object to the wavelength at which it emits the most intense light. It states that the peak wavelength, known as λmax, is inversely proportional to the temperature of the object.
This law is also referred to as Wien's displacement law or Wien displacement law. By applying Wien's law, we can determine the wavelength of peak radiation and the corresponding portion of the electromagnetic spectrum for different temperatures, such as a star at 30,000 K, the Sun's corona at 2,000,000 K, the surface of our skin at 297 K, and the Sun at 6000 K.
[tex]\[\lambda_{max}=\frac{b}{T}\][/tex] where [tex]\[b=2.898×10^6\][/tex] nm-K.
It signifies that the peak of the blackbody radiation curve for an object of temperature T occurs at a wavelength [tex]\[\lambda_{max}\][/tex]
The wavelength of peak radiation and the spectrum part it covers for each object are given below:
The peak wavelength of light emitted by a star at approximately 30,000 K is:
[tex]\[\lambda_{max}=\frac{b}{T}=\frac{2.898×10^6}{30000}=96.6\][/tex] nm
The spectrum portion covered by this is Ultraviolet.
The corona of the Sun, with a temperature of about 2,000,000 K, emits light with a peak wavelength of:
[tex]\[\lambda_{max}=\frac{b}{T}=\frac{2.898×10^6}{2000000}=1.45\][/tex] nm
The spectrum portion covered by this is X-rays.
At a temperature of around 297 K, the surface of our skin emits light with a peak wavelength:
[tex]\[\lambda_{max}=\frac{b}{T}=\frac{2.898×10^6}{297000}=9.76\][/tex] µm
The spectrum portion covered by this is Far-infrared.
The Sun, with a temperature of about 6000 K, emits light with a peak wavelength of:
[tex]\[\lambda_{max}=\frac{b}{T}=\frac{2.898×10^6}{6000}=483\][/tex] nm
The spectrum portion covered by this is Yellow-green.
Learn more about wavelength at: https://brainly.com/question/24452579
#SPJ11
write the missing words in each of the following 1. The value of the electric flux ($) will be maximum when the angle between the uniform electric field (E) and the normal to the surface of the area equal to ..... 2. The formula of the work done (W) is: .......... 3. The relation between the electric field (E) and the electric potential (V) is ..... 4. If d is the distance between the two plates and A is the area of each plate, the capacitance of a parallel plate capacitor is given by 5. The charge (Q) stored in a capacitor can be given by..... 6. The product of the resistance of a conductor (R) and the current passing through it (I) is 7. The unit of the magnetic flux density is..... 8. A region in which many atoms have their magnetic field aligned is called a
The unit of the magnetic flux density is tesla (T), and a region in which many atoms have their magnetic field aligned is called a magnetic domain.Write a final answer:The missing words in each of the following are:1. 90 degrees2. W = F × d × cos(θ)3. E = -dV/dx4. C = εA/d5. Q = CV6. P = VI7. tesla (T)8. magnetic domain
1. The value of the electric flux ($) will be maximum when the angle between the uniform electric field (E) and the normal to the surface of the area is equal to 90 degrees.2. The formula of the work done (W) is: W = F × d × cos(θ), where F is the force, d is the displacement, and θ is the angle between the force and displacement.3. The relation between the electric field (E) and the electric potential (V) is E = -dV/dx, where dx is the distance between the points where the potential is measured.
4. If d is the distance between the two plates and A is the area of each plate, the capacitance of a parallel plate capacitor is given by C = εA/d, where ε is the permittivity of the medium between the plates.5. The charge (Q) stored in a capacitor can be given by Q = CV, where C is the capacitance and V is the potential difference between the plates.
6. The product of the resistance of a conductor (R) and the current passing through it (I) is P = VI, where P is the power dissipated by the conductor.7. The unit of the magnetic flux density is tesla (T).8. A region in which many atoms have their magnetic field aligned is called a magnetic domain.Write a conclusion:In conclusion, the maximum value of electric flux is attained when the uniform electric field (E) and the surface normal of the area are 90 degrees apart.
Additionally, the formula of the work done (W) is W = F × d × cos(θ), and the capacitance of a parallel plate capacitor is given by C = εA/d. The relationship between the electric field (E) and the electric potential (V) is E = -dV/dx, and the charge (Q) stored in a capacitor can be given by Q = CV.
Finally, the unit of the magnetic flux density is tesla (T), and a region in which many atoms have their magnetic field aligned is called a magnetic domain.Write a final answer:The missing words in each of the following are:1. 90 degrees2. W = F × d × cos(θ)3. E = -dV/dx4. C = εA/d5. Q = CV6. P = VI7. tesla (T)8. magnetic domain
Learn more about electric here,
https://brainly.com/question/14306881
#SPJ11
A particle of mass m is situated somewhere in between planets X and Y. The particle's location is at a distance d from planet X and at a distance 1.5d from planet Y. If planet X has a mass of M, and planet Y has a mass of 3M, then which planet exerts greater gravitational force on the particle? By how much, in percent?
Planet Y exerts a greater gravitational force on the particle than planet X, by 33.33%.
To find out which planet exerts greater gravitational force on the particle and the percent difference, use the formula for gravitational force:
F = G(m1m2/d^2)
where F is the gravitational force between the two objects, G is the gravitational constant, m1 and m2 are the masses of the two objects, and d is the distance between them.
Mass of the particle = m
Distance of the particle from planet X = d
Distance of the particle from planet Y = 1.5d
Mass of planet X = M
Mass of planet Y = 3M
Calculate the gravitational force on the particle due to planet X:
Fx = G(Mm/d^2)
Calculate the gravitational force on the particle due to planet Y:
Fy = G(3Mm/2.25d^2)
Simplifying:
Fy = (4/3)G(Mm/d^2)
The gravitational force on the particle due to planet Y is (4/3) times the gravitational force on the particle due to planet X. This means that planet Y exerts a greater gravitational force on the particle than planet X, by a factor of (4/3) - 1 = 1/3. Converting this to a percentage, we get:
Percentage difference = (1/3) * 100% = 33.33%
Therefore, planet Y exerts a greater gravitational force on the particle than planet X, by 33.33%.
Learn more about gravitational force: https://brainly.com/question/24783651
#SPJ11
Suppose that a car is 900 kg and has a suspension system that has a force constant k 6.53x104 N/m. The car hits a bump and bounces with an amplitude of 0.100 m. What is the car's displacement (x) when its vertical velocity is 0.500 m/s?
Suppose that a car is 900 kg and has a suspension system that has a force constant k 6.53x104 N/m. The car hits a bump and bounces with an amplitude of 0.100 m. when the car's vertical velocity is 0.500 m/s, its displacement (x) is approximately 0.083 meters.
To find the car's displacement (x) when its vertical velocity is 0.500 m/s, we need to use the principles of energy conservation.
The total mechanical energy of the car is conserved during the oscillatory motion. It consists of kinetic energy (KE) and potential energy (PE).
At the point where the car's vertical velocity is 0.500 m/s, all of its initial potential energy is converted into kinetic energy.
The potential energy of the car at its maximum displacement (amplitude) is given by:
PE = (1/2) × k × x^2
where k is the force constant of the suspension system and x is the displacement from the equilibrium position.
The kinetic energy of the car when its vertical velocity is 0.500 m/s is given by:
KE = (1/2) × m × v^2
where m is the mass of the car and v is its vertical velocity.
Since the total mechanical energy is conserved, we can equate the potential energy and kinetic energy:
PE = KE
(1/2) × k × x^2 = (1/2)× m × v^2
Substituting the given values:
(1/2) × (6.53 x 10^4 N/m) × x^2 = (1/2) × (900 kg) × (0.500 m/s)^2
Rearranging the equation to solve for x:
x^2 = (900 kg × (0.500 m/s)^2) / (6.53 x 10^4 N/m)
x^2 = 0.006886
Taking the square root of both sides:
x ≈ 0.083 m
Therefore, when the car's vertical velocity is 0.500 m/s, its displacement (x) is approximately 0.083 meters.
To learn more about energy conservation visit: https://brainly.com/question/166559
#SPJ11
When the frequency of the AC voltage is doubled, the capacitive reactance whille the inductive reactance halves; doubles doubles; halves halves; halves doubles; doubles
When the frequency of the AC voltage is doubled, the capacitive reactance halves while the inductive reactance doubles.
When the frequency of the AC voltage is doubled, the capacitive reactance halves while the inductive reactance doubles. This is because the reactance of a capacitor is inversely proportional to the frequency of the AC voltage, while the reactance of an inductor is directly proportional to the frequency of the AC voltage.Capacitive reactance, denoted by XC, is given by the formula:XC = 1 / (2πfC)Where f is the frequency of the AC voltage, and C is the capacitance of the capacitor.
Since the reactance of the capacitor is inversely proportional to the frequency of the AC voltage, when the frequency of the AC voltage is doubled, the capacitive reactance will be halved.On the other hand, inductive reactance, denoted by XL, is given by the formula:XL = 2πfLWhere f is the frequency of the AC voltage, and L is the inductance of the inductor. Since the reactance of the inductor is directly proportional to the frequency of the AC voltage, when the frequency of the AC voltage is doubled, the inductive reactance will be doubled.
In conclusion, when the frequency of the AC voltage is doubled, the capacitive reactance halves while the inductive reactance doubles.
Learn more about frequency here,
https://brainly.com/question/254161
#SPJ11
The only force acting on a 2.3 kg body as it moves along the positive x axis has an x component Fx = −4×N, where x is in meters. The velocity of the body at x=1.4 m is 9.1 m/s. (a) What is the velocity of the body at x=4.6 m ? (b) At what positive value of x will the body have a velocity of 5.5 m/s ? (a) Number ________________ Units _________________
(b) Number ________________ Units _________________
(a)
The velocity of the body at x = 4.6 m is -2.69 m/s.
Number: -2.69
Units: m/s
(b)
The positive value of x where the body will have a velocity of 5.5 m/s is 9.6 m.
Number: 9.6
Units: m
Mass of the body, m = 2.3 kg
Force acting on the body, Fx = −4 N
Initial velocity of the body, u = 0 m/s
Velocity of the body at x = 1.4 m, v = 9.1 m/s
Let's find the acceleration of the body at x = 1.4 ma
= F/m
= (-4 N)/2.3 kg
= -1.74 m/s²
(a)
Now, let's find the velocity of the body at x = 4.6 m
Final position of the body, x = 4.6 m
Initial position of the body, x = 1.4 m
Distance covered by the body, s = x - u = 4.6 - 1.4 = 3.2 m
Using the second equation of motion,
v² = u² + 2as
v² = 0 + 2 × (-1.74) × 3.2
v = -2.69 m/s
The velocity of the body at x = 4.6 m is -2.69 m/s.
Number: -2.69
Units: m/s
(b)
Now, let's find the positive value of x where the body will have a velocity of 5.5 m/s.
Final velocity of the body, v = 5.5 m/s
Initial velocity of the body, u = 0 m/s
Let the distance covered by the body be s meters.
Using the third equation of motion,v² = u² + 2as
5.5² = 0 + 2a × s
We know, a = -1.74 m/s²
5.5² = 2 × (-1.74) × s
s = 8.2 m
Therefore, the positive value of x where the body will have a velocity of 5.5 m/s is 1.4 + 8.2 = 9.6 m.
Number: 9.6
Units: m
Learn more about the equation of motion:
brainly.com/question/24018491
#SPJ11
Which of the following vectors is equivalent to 50 [553°E]? a. [-30,40] b. [40, -30] c. [-40, 30] d. [-40, -30] 2. Which of the following vectors is not collinear with the others? a. [-3,7] b. [6,-14] c. [-30, 70] d. [9, 21] 3. Determine the result of the dot product: [3,-4] [2,5] a. [6, -20] b. 14 C. -14 d. 26 4. Which of the following expressions involving dot product and cross product cannot be evaluated? a. (a.b) × (d.d) c. (a. b) + (ĉ. d) d. (axb). (¿xd) b. (axb) x (exd) 5. Albert is pushing his broken-down car. He pushed with a force of 8000 N at an angle of 10° to the horizontal to move the car 20 metres. How much work has Albert done? a. 75175 Nm. b. 160000 Nm c. 27784 Nm d. 157569 Nm 6. Determine the result of the cross product: [1, -2,3] x [-4,5,-6] b. [3, 6, 3] c. [27,-18, 13] a. [-3, -6, -3] d. [7,-8, 9] 7. Determine the angle between the vectors [1, 2, 3] and [4, 5, 6] a. 15.2° b. 12.9 c. 13.1 d. 0.97 8. For what value(s) of k are the two vectors [k, 2, 3] and [1, k, -2] perpendicular to each other? a. k = 2 and -2 b. k=2 c. k=-2 k=3 9. Choose the vector equation of a line through the point (4, 7) with direction vector m = [1, 5). a. (x, y) = [1, 5] + t[4, 7] c. (x, y] H [4, 7) + t[-5, 1) b. (x, y) = [1, 5] + t[-7,4] d. [x, y] [4, 7] + t(1, 5] 10. Which of the following is a scalar equation of the line with vector equation [x, y] [1, 3] + t[-1, -2]? a. 2x+y+1=0 b. x+2y-1=0 6.2x-y+1=0 d. x-2y+1=0 11. Which of the following is a vector equation of the line 2x - y = 7? a. [x, y] [4, 3] + t[1, 2] b. [x, y] = [2, 7] + [2, 4] 12. Which of the following does not have a normal of [1, 1, 1]? a. [x, y, z) = [2, 3, 1] + [-2, 3, -1] b. [x, y, z] [19, 12, 7] + t[-4, 5, -2] c. [x, y] = [4, 1] + t[2, -1] d. [x, y] = [5, 3] + t[-3, -6] c. [x, y, z) = [4, 0, 1] + t[1, 0, -1] d. [x, y, z]= [0, 0, 0] + [13, -7, -6]
Answer:
1. Option c. [-40, 30].
2. Option c. [-30, 70].
3. Option b. 14.
4. Option d. (axb) x (exd).
5. Option d. 157569 Nm.
6. Option c. [27, -18, 13].
7. Option a. 15.2°.
8. Option k = 2 and -2.
9. Option b. (x, y) = [1, 5] + t[-7, 4].
10. Option c. 6.2x-y+1=0.
11. Option a. [x, y] = [4, 3] + t[1, 2].
12. Option d. [x, y] = [5, 3] + t[-3, -6].
Here's an explanation:
1. The vector equivalent to 50 [553°E] is c. [-40, 30].
2. The vector that is not collinear with the others is c. [-30, 70].
3. The result of the dot product of [3, -4] and [2, 5] is b. 14.
4. The expression that cannot be evaluated is d. (axb) x (exd).
5. The work that Albert has done is d. 157569 Nm.
6. The result of the cross product of [1, -2, 3] and [-4, 5, -6] is c. [27, -18, 13].
7. The angle between the vectors [1, 2, 3] and [4, 5, 6] is a. 15.2°.
8. The value of k that makes the two vectors [k, 2, 3] and [1, k, -2] perpendicular to each other is k = 2 and -2.
9. The vector equation of a line through the point (4, 7) with direction vector m = [1, 5) is b. (x, y) = [1, 5] + t[-7, 4].
10. The scalar equation of the line with vector equation [x, y] = [1, 3] + t[-1, -2] is c. 6.2x-y+1=0.
11. The vector equation of the line 2x - y = 7 is a. [x, y] = [4, 3] + t[1, 2].
12. The equation that does not have a normal of [1, 1, 1] is d. [x, y] = [5, 3] + t[-3, -6].
Learn more about vector: https://brainly.com/question/15519257
#SPJ11