The smallest observable detail utilizing a 500-MHz military radar is 0.6 meters. This means that the radar is capable of detecting objects or details that are larger than or equal to 0.6 meters in size.
The smallest observable detail, also known as the resolution, can be determined by considering the wavelength of the instrument.
In this case, we have a 500-MHz military radar, which operates at a frequency of 500 million cycles per second.
To find the wavelength, we can use the formula:
Wavelength = Speed of light / Frequency
The speed of light is approximately 3 x [tex]10^8[/tex] meters per second.
Substituting the values into the formula, we have:
Wavelength = (3 x [tex]10^8[/tex] m/s) / (500 x [tex]10^6[/tex] Hz)
Simplifying, we get:
Wavelength = 0.6 meters
Therefore, the smallest observable detail using a 500-MHz military radar is 0.6 meters.
In summary, the smallest observable detail utilizing a 500-MHz military radar is 0.6 meters.
This means that the radar is capable of detecting objects or details that are larger than or equal to 0.6 meters in size.
Smaller details or objects may not be discernible by the radar due to the limitations imposed by its wavelength.
Learn more about radar here:
https://brainly.com/question/31783853
#SPJ11
Find the power dissipated in each of these extension cords: a) an extension cord having a 0.0575 Ω resistance and through which 4.88 A is flowing. ____________ W b) a cheaper cord utilizing thinner wire and with a resistance of 0.28 Ω. __________W
The power dissipated in the extension cord is 1.13 W and The power dissipated in the cheaper cord is 5.23
1.The power dissipated in each of these extension cords can be found using the formula: P = I²Rwhere:P = power I = current R = resistance
2. For an extension cord having a 0.0575 Ω resistance and through which 4.88 A is flowing, the power dissipated can be calculated using the above formula as: P = (4.88 A)² x 0.0575 ΩP = 1.13 W. Therefore, the power dissipated in the extension cord is 1.13 W.
3. For a cheaper cord utilizing thinner wire and with a resistance of 0.28 Ω, the power dissipated can be calculated using the above formula as: P = (4.88 A)² x 0.28 ΩP = 5.23 W. Therefore, the power dissipated in the cheaper cord is 5.23 W.
Learn more about power:
https://brainly.com/question/13600515
#SPJ11
A 1.00 kg block is attached to a spring with spring constant 18.0 N/m . While the block is sitting at rest, a student hits it with a hammer and almost instantaneously gives it a speed of 32.0 cm/s . What are
The amplitude of the subsequent oscillations?
The block's speed at the point where x= 0.550 A?
The amplitude of the subsequent oscillations is 0.0754 m and the block's speed at the point where x = 0.550A is approximately 2.26 m/s.
To find the amplitude of the subsequent oscillations, we need to consider the conservation of mechanical energy.
When the block is hit by the hammer, it gains kinetic energy.
This kinetic energy will be converted into potential energy as the block oscillates back and forth.
The total mechanical energy of the system is given by the sum of kinetic energy and potential energy:
E = K + U
Initially, the block is at rest, so the initial kinetic energy is zero. The potential energy at the equilibrium position (where x = 0) is also zero.
Therefore, the initial total mechanical energy is zero.
When the block is displaced from the equilibrium position, it gains potential energy due to the spring's deformation.
At the maximum displacement (amplitude), all the kinetic energy is converted into potential energy.
So, at the amplitude, the total mechanical energy is equal to the potential energy:
E_amplitude = U_amplitude
The potential energy of a spring is given by the equation:
U = (1/2)k[tex]x^2[/tex]
where k is the spring constant and x is the displacement from the equilibrium position.
Since the block is at rest when it is hit by the hammer, the initial kinetic energy is zero.
Therefore, the total mechanical energy after the hit is equal to the potential energy at the amplitude:
E_amplitude = U_amplitude = (1/2)k[tex]x^2[/tex]
Given that the mass of the block is 1.00 kg and the spring constant is 18.0 N/m, we can substitute these values into the equation:
E_amplitude = (1/2)(18.0 N/m)([tex]x^2[/tex])
To find the amplitude, we need to solve for x.
We know that the initial speed of the block after it is hit is 32.0 cm/s (or 0.32 m/s).
The kinetic energy at this point is given by:
K = (1/2)m[tex]v^2[/tex]
Substituting the values, we have:
(1/2)(1.00 kg)(0.32 m/s)^2 = (1/2)(18.0 N/m)([tex]x^2[/tex])
Simplifying and solving for x, we get:
0.0512 J = 9.0 N/m * [tex]x^2[/tex]
[tex]x^2[/tex] = 0.005688
x = 0.0754 m
Therefore, the amplitude of the subsequent oscillations is 0.0754 m.
To find the block's speed at the point where x = 0.550A, we can use the conservation of mechanical energy.
At any point during the oscillation, the total mechanical energy remains constant.
E = K + U
Initially, the total mechanical energy is zero.
At the point where x = 0.550A, all the potential energy is converted into kinetic energy:
E_point = K_point = (1/2)k(0.550A)^2
Substituting the values, we have:
E_point = (1/2)(18.0 N/m)(0.550A)^2
Simplifying, we get:
E_point = 2.5485 Nm
The kinetic energy at this point is equal to the total mechanical energy:
K_point = E_point = 2.5485 J
To find the speed, we can use the equation for kinetic energy:
K = (1/2)m[tex]v^2[/tex]
Substituting the values, we have:
2.5485 J = (1/2)(1.00 kg)[tex]v^2[/tex]
Simplifying, we get:
[tex]v^2[/tex]2 = 5.097
v = √(5.097) ≈ 2.26 m/s
Therefore, the block's speed at the point where x = 0.550A is approximately 2.26 m/s.
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
A long solenoid with n= 35 turns per centimeter and a radius of R= 12 cm carries a current of i= 35 mA. Find the magnetic field in the solenoid. The magnetci field, Bo 176.6 x Units UT If a straight conductor is positioned along the axis of the solenoid and carries a current of 53 A, what is the magnitude of the net magnetic field at the distance R/2 from the axis of the solenoid? The net magnetic field, Bret = 176.61 Units
Answer:
1) The magnetic field inside the solenoid is approximately 0.0389 Tesla.
2) The magnitude of the net magnetic field at a distance R/2 from the axis of the solenoid is approximately 0.0424 Tesla.
To find the magnetic field inside the solenoid, we can use the formula for the magnetic field inside a solenoid:
B = μ₀ * n * i
Where:
B is the magnetic field
μ₀ is the permeability of free space (4π * 10^(-7) T·m/A)
n is the number of turns per unit length
i is the current
n = 35 turns/cm
= 35 * 100 turns/m
= 3500 turns/m
i = 35 mA
= 35 * 10^(-3) A
Substituting the values into the formula:
B = (4π * 10^(-7) T·m/A) * (3500 turns/m) * (35 * 10^(-3) A)
Calculating:
B ≈ 0.0389 T
Therefore, the magnetic field inside the solenoid is approximately 0.0389 Tesla.
To find the magnitude of the net magnetic field at a distance R/2 from the axis of the solenoid due to the solenoid and the straight conductor, we can sum the magnetic fields produced by each separately.
The magnetic field at a distance R/2 from the axis of the solenoid can be found using the formula:
B_sol = μ₀ * n * i
n = 3500 turns/m
i = 35 * 10^(-3) A
Substituting the values into the formula:
B_sol = (4π * 10^(-7) T·m/A) * (3500 turns/m) * (35 * 10^(-3) A)
Calculating:
B_sol ≈ 0.0389 T
The magnetic field at a distance R/2 from a long straight conductor carrying a current can be found using Ampere's law:
B_conductor = (μ₀ * i) / (2π * R/2)
i = 53 A
R = 12 cm = 0.12 m
Substituting the values into the formula:
B_conductor = (4π * 10^(-7) T·m/A * 53 A) / (2π * 0.12 m)
Calculating:
B_conductor ≈ 0.0035 T
To find the net magnetic field, we can add the magnitudes of the magnetic fields produced by the solenoid and the conductor:
B_net = |B_sol| + |B_conductor|
Substituting the values:
B_net = |0.0389 T| + |0.0035 T|
Calculating:
B_net ≈ 0.0424 T
Therefore, the magnitude of the net magnetic field at a distance R/2 from the axis of the solenoid is approximately 0.0424 Tesla.
Learn more about solenoid, here
https://brainly.com/question/1873362
#SPJ11
Please answer the following questions in detail:
1. What is the relation between the voltage the plate charge (top) and the capacitance? Explain and provide and equation.
2. How does the Capacitance vary with the area and separation ? Explain and provide and equation.
3. Calculate the electric field and the stored energy when the distance (separation between the plates) are 5.0mm and 10.0mm. (Show your work). When d= 5.00 mm then: V = 1.012 V, Area= 100 mm², Plate Charge= 1.79E-13 C, Capacitance= 0.18E-12 F. When d=10 mm then: V= 2.024 V, Area= 100 mm², Plate charge= 1.79E-13 C, Capacitance= 0.09E-12 F
What is the relation between the voltage the plate charge (top) and the capacitance?:
Capacitance is directly proportional to the plate area and inversely proportional to the distance between the plates. The greater the capacitance, the more plate charge a capacitor can hold at a specified voltage. The greater the voltage, the more charge the capacitor can hold. The capacitance is calculated using the following equation:
C= (εA)/d, where C is capacitance, ε is the dielectric constant of the material between the plates, A is the plate area, and d is the distance between the plates.
The plate charge is calculated using the equation Q= CV, where Q is plate charge, C is capacitance, and V is the voltage.
2. The variation of capacitance with area and separation:
The capacitance of a parallel-plate capacitor is directly proportional to the surface area of the plates and inversely proportional to the distance between them.
The formula for capacitance is C= ε(A/d), where ε is the permittivity of free space, A is the surface area of one plate, and d is the distance between the plates. Capacitance is proportional to the plate area and inversely proportional to the plate separation.
3. Calculation of electric field and stored energy:
d = 5.0 mm, V = 1.012 V, A = 100 mm², Plate charge = 1.79 × 10⁻¹³ C, Capacitance = 0.18 × 10⁻¹² F.ε₀ = 8.85 × 10⁻¹² F/m
Electric field = V/d = 1.012/0.005 = 202.4 V/m
Stored energy = 1/2CV² = 0.5 × 0.18 × 10⁻¹² × (1.012)² = 9.07 × 10⁻¹⁴ J
When d = 10.0 mm, V = 2.024 V, A = 100 mm², Plate charge = 1.79 × 10⁻¹³ C, Capacitance = 0.09 × 10⁻¹² F
Electric field = V/d = 2.024/0.01 = 202.4 V/m
Stored energy = 1/2CV² = 0.5 × 0.09 × 10⁻¹² × (2.024)² = 18.4 × 10⁻¹⁴ J
Therefore, the electric field for both situations is 202.4 V/m. The stored energy when the separation is 5.0 mm is 9.07 × 10⁻¹⁴ J, and when the separation is 10.0 mm, it is 18.4 × 10⁻¹⁴ J.
Learn more about capacitance here: https://brainly.com/question/21851402
#SPJ11
When a bar magnet is placed static near a loop of wire, a magnetic field will the loop. A. moves B. induce C. change D. penetrates A device that converts mechanical energy into electrical energy is A. Motor B. Generator C. Loudspeaker D. Galvanometer
When a bar magnet is placed near a loop of wire, it induces a magnetic field in the loop. A device that converts mechanical energy into electrical energy is a generator.
When a bar magnet is placed near a loop of wire, it induces a magnetic field in the loop. This phenomenon is known as electromagnetic induction. As the magnetic field of the bar magnet changes, it creates a changing magnetic flux through the loop, which in turn induces an electromotive force (EMF) and an electric current in the wire. This process is the basis of how generators and other electrical devices work. Therefore, the correct answer is B. induce.
A device that converts mechanical energy into electrical energy is a generator. A generator utilizes the principle of electromagnetic induction to convert mechanical energy, such as rotational motion, into electrical energy. It consists of a coil of wire that rotates within a magnetic field. As the coil rotates, the magnetic field induces a changing magnetic flux through the coil, which generates an EMF and produces an electric current. This electric current can be used to power electrical devices or charge batteries. Therefore, the correct answer is B. Generator.
Learn more about magnetic fields here:
https://brainly.com/question/19542022
#SPJ11
A bullet is dropped from the top of the Empire State Building while another bullet is fired downward from the same location. Neglecting air resistance, the acceleration of a. none of these b. it depends on the mass of the bullets c. the fired bullet is greater. Od, each bullet is 9.8 meters per second per second. e. the dropped bullet is greater.
The acceleration of both bullets, neglecting air resistance, would be the same.
Hence, the correct answer is:
a. None of these (the acceleration is the same for both bullets)
When a bullet is dropped from the top of the Empire State Building or fired downward from the same location, the only significant force acting on both bullets is gravity.
In the absence of air resistance, the acceleration experienced by any object near the surface of the Earth is constant and equal to approximately 9.8 meters per second squared (m/s²), directed downward.
The mass of the bullets does not affect their acceleration due to gravity. This is known as the equivalence principle, which states that the gravitational acceleration experienced by an object is independent of its mass.
Therefore, regardless of their masses or initial velocities, both bullets would experience the same acceleration of 9.8 m/s² downward.
Hence, the correct answer is:
a. None of these (the acceleration is the same for both bullets)
Learn more about equivalence principle, here
https://brainly.com/question/32296932
#SPJ11
A
few facts and reminders that will be helpful.
The Stefan-Boltzmann constant is σ = 5.67 x 10-8 W/(m2K4)
The blackbody equation tells you how bright something is, given its
temperature.
That "brig
1. Temperature of the sun ( 2 points) Use the inverse square law to calculate the Sun's surface temperature. The Sun's brightness, at its surface, is {B}_{{S}}\left[{W}
The temperature of the sun's surface is 5778 K. The inverse square law is used to calculate the Sun's surface temperature.
The Stefan-Boltzmann constant is σ = 5.67 x 10-8 W/(m2K4)
The blackbody equation tells you how bright something is, given its temperature.
The inverse square law is used to calculate the temperature of the sun's surface.
The sun's brightness, at its surface, is [W/m2] = 6.34 x 107 W/m2.
We know that the Stefan-Boltzmann constant is given by σ = 5.67 x 10-8 W/(m2K4).
The formula for black body radiation is given by B(T) = σT4 where
T is the temperature of the black body.
Brightness is given by [W/m2] = 6.34 x 107 W/m2.
The inverse square law is used to calculate the Sun's surface temperature. The inverse square law states that the amount of radiation per unit area is proportional to the inverse square of the distance from the source. Let the temperature of the sun be T. The distance between the earth and the sun is approximately 1.496 x 1011 meters.
So, the brightness of the sun at the earth's distance is given by L/4π (1.496 x 1011) 2 = 6.34 x 107 W/m2
where L is the luminosity of the sun.
We know that L = 3.846 x 1026 W.
Substituting this value of L in the above equation, we get B = 6.34 x 107 W/m2.
Using the black body radiation equation, we can write B(T) = σT4.
Now, substituting the value of B in the above equation, we get 6.34 x 107 = σT4.
Thus, T4 = 6.34 x 107 / σ.
T4 = 6.34 x 107 / 5.67 x 10-8.
T4 = 1.12 x 1016.K4 - (T/5778)4.
The temperature of the sun is T = 5778 K.
The temperature of the sun's surface is 5778 K.
To know more about luminosity visit:
brainly.com/question/33171892
#SPJ11
A straight wire carries a current of 5 mA and is oriented such that its vector
length is given by L=(3i-4j+5k)m. If the magnetic field is B=(-2i+3j-2k)x10^-3T, obtain
the magnetic force vector produced on the wire.
Justify your answers with equations and arguments
The magnetic force produced by a straight wire carrying a current of 5 m
A is given as follows:The magnetic force vector produced on the wire is:F = IL × BWhere I is the current flowing through the wire, L is the vector length of the wire and
B is the magnetic field acting on the wire.
From the problem statement,I = 5 mA = 5 × 10^-3AL = 3i - 4j + 5kmandB = -2i + 3j - 2k × 10^-3TSubstituting these values in the equation of magnetic force, we get:F = 5 × 10^-3A × (3i - 4j + 5k)m × (-2i + 3j - 2k) × 10^-3T= -1.55 × 10^-5(i + j + 7k) NCoupling between a magnetic field and a current causes a magnetic force to be exerted. The magnetic force acting on the wire is orthogonal to both the current direction and the magnetic field direction. The direction of the magnetic force is determined using the right-hand rule. A quantity of positive charge moving in the direction of the current is affected by a force that is perpendicular to both the velocity of the charge and the direction of the magnetic field.
Learn more about Equation here,
https://brainly.com/question/29174899
#SPJ11
Four 7.5-kg spheres are located at the corners of a square of side 0.65 m Part A Calculate the magnitude of the gravitational force exerted on one sphere by the other three Calculate the direction of the gravitational force exerted on one sphere by the other three Express your answer to two significant figures and include the appropriate units. 0
The direction of the gravitational force exerted on one sphere by the other three is always towards the center of mass of the other three spheres. Since the spheres are located at the corners of a square, the force vectors will be directed towards the center of the square.
To calculate the magnitude of the gravitational force exerted on one sphere by the other three, we can use the formula for gravitational force:
where F is the gravitational force, G is the gravitational constant (approximately 6.674 × [tex]10^-11 Nm^2/kg^2)[/tex], [tex]m_1[/tex] and [tex]m_2[/tex] are the masses of the two objects, and r is the distance between their centers.
F =[tex]G * (m_1 * m_2) / r^2,[/tex]
In this case, the mass of each sphere is given as 7.5 kg, and the distance between the centers of the spheres is equal to the side length of the square, which is 0.65 m. By substituting these values into the formula, we can calculate the gravitational force exerted on one sphere by the other three.
The direction of the gravitational force exerted on one sphere by the other three is always towards the center of mass of the other three spheres. Since the spheres are located at the corners of a square, the force vectors will be directed towards the center of the square.
To calculate the magnitude of the gravitational force exerted on one sphere by the other three, we use the formula F =[tex]G * (m_1 * m_2) / r^2[/tex]. This formula allows us to determine the gravitational force between two objects based on their masses and the distance between their centers.
In this case, we have four spheres, each with a mass of 7.5 kg. To calculate the force exerted on one sphere by the other three, we treat each sphere as the first object (m1) and the other three spheres as the second object (m2). We then calculate the force for each combination and sum up the magnitudes of the forces.
The distance between the centers of the spheres is given as the side length of the square, which is 0.65 m. This distance is used in the formula to calculate the gravitational force.
The direction of the gravitational force exerted on one sphere by the other three is always towards the center of mass of the other three spheres. Since the spheres are located at the corners of a square, the force vectors will be directed towards the center of the square. This means that the gravitational force vectors will point towards the center of the square, regardless of the specific positions of the spheres.
Learn more about gravitation here:
https://brainly.com/question/3009841
#SPJ11
Two wires carrying a 3.4-A current in opposite directions are 0.013m apart. What is the force per unit length on each wire?
Answer: x 10⁻⁴N/m
Is the force attractive or repulsive?
Answer:
The force per unit length on each wire is 10⁻⁴ N/m and the force is repulsive.
The current passing through the wires I = 3.4A
Distance between the two wires is d = 0.013m
The force per unit length on each wire is calculated using the formula:
F/L = μ₀I¹I²/2πd
Where,
F/L is the force per unit length
μ₀ is the permeability constant
I¹ and I² are the currents passing through the wires
2πd is the separation between the two wires
Substituting the values in the formula, we get
F/L = (4π x 10⁻⁷ Tm/A) x (3.4A)² / 2π(0.013m)
= 10⁻⁴ N/m
Therefore, the force per unit length on each wire is 10⁻⁴ N/m.
The two wires carrying current in opposite directions repel each other. Therefore, the force is repulsive.
Learn more about the force per unit length:
brainly.com/question/18917488
#SPJ11
Find Tx (kinetic energy operator)
Tx = -h²δ² 2mδx²
The operator is Tx = -h²/2m * d²/dx², is called the kinetic energy operator.
The kinetic energy operator, often denoted as T or K, is a mathematical operator in quantum mechanics that represents the kinetic energy of a particle. In the case of one-dimensional motion, the kinetic energy operator is given by:
T = -((ħ^2)/(2m)) * d^2/dx^2
where:
- T is the kinetic energy operator
- ħ (pronounced "h-bar") is the reduced Planck's constant (h-bar = h / (2π))
- m is the mass of the particle
- d^2/dx^2 is the second derivative with respect to the position coordinate x
Please note that this expression assumes the particle is free and does not include any potential energy terms.
Learn more about kinetic energy https://brainly.com/question/8101588
#SPJ11
A scuba tank, when fully submerged, displaces 14.1 L of seawater. The tank itself has a mass of 13.5 kg and, when "full," contains 1.25 kg of air. Assuming only a weight and buoyant force act, determine the net force (magnitude) on the fully submerged tank at the beginning of a dive (when it is full of air). Express your answer with the appropriate units. X Incorrect; Try Again; 2 attempts remaining Express your answer with the appropriate units.
The net force on the tank is 10.13 Newtons (N). So, the coorect anser is 10.13 N.
To determine the net force, we need to consider the weight of the tank and the buoyant force acting on it.
1. Weight of the tank:
Weight = mass * acceleration due to gravity
Weight = 13.5 kg * 9.8 m/s^2
The weight of the tank is approximately 132.3 N.
2. Buoyant force:
Buoyant force = density of fluid * volume displaced * acceleration due to gravity
First, let's convert the volume of seawater displaced by the tank to cubic meters:
Volume = 14.1 L * 0.001 m^3/L
The volume is approximately 0.0141 m^3.
Now, let's calculate the buoyant force using the density of seawater, which is approximately 1025 kg/m^3:
Buoyant force = 1025 kg/m^3 * 0.0141 m^3 * 9.8 m/s^2
The buoyant force is approximately 142.43 N.
3. Net force:
Net force = Buoyant force - Weight
Net force = 142.43 N - 132.3 N
The net force on the fully submerged scuba tank at the beginning of a dive is approximately 10.13 N.
Therefore, the net force on the tank is 10.13 Newtons (N).
Learn more about buoyant force
https://brainly.com/question/21990136
#SPJ11
Determining the value of an unknown resistance using Wheatstone Bridge and calculating the stiffness of a given wire are among the objectives of this experiment. Select one: True o False
The statement "Determining the value of an unknown resistance using Wheatstone Bridge and calculating the stiffness of a given wire are among the objectives of this experiment" is true because the Wheatstone bridge is a circuit used to measure the value of an unknown resistance. It is a very accurate method of measuring resistance, and is often used in scientific and industrial applications.
Here are some of the objectives of the Wheatstone bridge experiment:
To determine the value of an unknown resistance using a Wheatstone bridge. To calculate the stiffness of a given wire from its resistance. To investigate the factors that affect the resistance of a wire, such as its length, cross-sectional area, and material. To learn how to use a Wheatstone bridge to measure resistance.The Wheatstone bridge is a versatile and powerful tool that can be used to measure resistance, calculate stiffness, and investigate the factors that affect the resistance of a wire. It is a valuable tool for scientists and engineers in a variety of field.
To learn more about resistance visit: https://brainly.com/question/25997303
#SPJ11
A bar is free to fall while completing the circuit. The resistor has resistance 38.8 Ω. The rod has a length of 1.42 m. The magnetic field is out of the page a magnitude of 0.10 T. The bar is falling with a speed of 95.77 m/s, and the speed is now constant because the force of gravity and the electromotive force are balanced. What is the mass of the bar?
From the equation of motion, the gravitational force acting on the bar is equal to its mass times the acceleration due to gravity.So, the mass of the bar is given as:m = F/g= 0.4038 N/9.81 m/s²= 0.0411 kgHence, the mass of the bar is 0.0411 kg.
A bar of mass m is free to fall while completing the circuit. The resistor has resistance 38.8 Ω. The rod has a length of 1.42 m. The magnetic field is out of the page at a magnitude of 0.10 T. The bar is falling with a speed of 95.77 m/s, and the speed is now constant because the force of gravity and the electromotive force are balanced.In order to determine the mass of the bar,
we need to make use of the following expression:emf = Blvwhere,emf = Electromotive forceB = Magnetic fieldl = Length of the conductorv = Velocity of the conductorNow, the electromotive force induced is given as:emf = Blv= 0.10 T × 1.42 m × 95.77 m/s= 1.365 VThe voltage drop across the resistor is equal to the electromotive force, therefore,
the current through the circuit is given by:V = IR38.8 Ω = I × 1.365 VI = 28.32 AThe force acting on the conductor is given by:F = BIl= 0.10 T × 1.42 m × 28.32 A= 0.4038 N
From the equation of motion, the gravitational force acting on the bar is equal to its mass times the acceleration due to gravity.So, the mass of the bar is given as:m = F/g= 0.4038 N/9.81 m/s²= 0.0411 kgHence, the mass of the bar is 0.0411 kg.
to know more about gravitational
https://brainly.com/question/23586829
#SPJ11
An energy service company wants to use hot springs to power a heat engine. If the groundwater is at 95 Celsius, estimate the maximum power output if the mass flux is 0.2 kg/s. The ambient temperature is 20 Celsius. Enter the value in kW, use all decimal places and enter only the numerical value.
The estimated maximum power output of the heat engine using hot springs with a groundwater temperature of 95 °C and a mass flux of 0.2 kg/s is approximately 0.0128 kW.
To estimate the maximum power output of the heat engine using hot springs, we can utilize the concept of the Carnot cycle, which provides an upper limit for the efficiency of a heat engine.
The Carnot efficiency is given by the formula:
η = 1 - (Tc/Th)
Where η is the efficiency, Tc is the temperature of the cold reservoir (ambient temperature), and Th is the temperature of the hot reservoir (groundwater temperature).
Given:
Tc = 20 °C = 293 K
Th = 95 °C = 368 K
The maximum power output can be calculated using the formula:
P = η * Q
Where P is the power output and Q is the heat transfer rate.
The heat transfer rate can be calculated using the formula:
Q = m * Cp * (Th - Tc)
Given:
m = 0.2 kg/s (mass flux)
Cp = specific heat capacity of water ≈ 4.18 kJ/kg°C
Let's calculate the maximum power output:
Tc = 293 K
Th = 368 K
m = 0.2 kg/s
Cp = 4.18 kJ/kg°C = 4.18 J/g°C = 4.18 * 10⁻³ J/kg°C
Q = m * Cp * (Th - Tc)
= 0.2 kg/s * 4.18 * 10⁻³ J/kg°C * (368 K - 293 K)
= 0.2 * 4.18 * 10⁻³ * 75
= 0.0627 kW
η = 1 - (Tc/Th)
= 1 - (293/368)
≈ 0.204
P = η * Q
= 0.204 * 0.0627 kW
≈ 0.0128 kW
Therefore, the estimated maximum power output of the heat engine using hot springs with a groundwater temperature of 95 °C and a mass flux of 0.2 kg/s is approximately 0.0128 kW.
Learn more about power output on:
https://brainly.com/question/20038729
#SPJ11
A machinist bores a hole of diameter \( 1.34 \mathrm{~cm} \) in a Part \( A \) steel plate at a temperature of \( 27.0^{\circ} \mathrm{C} \). You may want to review (Page) What is the cross-sectional
The problem is a case of linear expansion of solids. If there is a change in temperature in an object, then the length of the object also changes. And in this situation, the diameter of the hole changes. The diameter of a hole is directly proportional to the length of the plate. Hence, the formula for this situation would be ΔL=αLΔT
Where, ΔL is the change in length of the plate, L is the initial length of the plate, ΔT is the change in temperature of the plate, and α is the coefficient of linear expansion of the plate.
The formula for the diameter of the hole would beΔd=2αLΔTwhere, Δd is the change in diameter of the plate.
It is given that the initial diameter of the hole, d = 1.34 cm, the initial temperature, T = 27 °C, ΔT = 80 °C
Therefore, the change in diameter is,Δd = 2αLΔTWe know that steel is a metal and its coefficient of linear expansion, α is 1.2 × 10^(-5) K^(-1).
The value of L is not given.
So, let's assume that the coefficient of linear expansion of the steel is constant and also the value of L is constant.
Δd = 2αLΔTΔd
= 2 × 1.2 × 10^(-5) × L × 80Δd
= 1.92 × 10^(-3) L
The value of L can be calculated as,
L = Δd / (1.92 × 10^(-3))L = 0.7 m = 70 cm
Therefore, the length of the steel plate is 70 cm.
Thus, the answer is: The length of the steel plate is 70 cm.
Learn more about change in temperature here
https://brainly.com/question/27988898
#SPJ11
When you drop a rock into a well, you hear the splash 0.9 seconds later. The sound speed is 340 m/s. How deep is the well ? (Hint: the depth will defiitely be less than a kilometer..) Number Units If the depth of the well were doubled, would the time required to hear the splash be greater than 1.8 S equal to 1.8 S less than 1.8 S
The depth of the well is 306 meters. If the depth of the well were doubled, the time required to hear the splash would be greater than 1.8 seconds. This is because the time taken for the sound to travel is directly proportional to the depth of the well.
To calculate the depth of the well, we can use the formula:
depth = (speed of sound) x (time taken for sound to travel)
Given that the speed of sound is 340 m/s and the time taken to hear the splash is 0.9 seconds, we can calculate the depth of the well:
depth = 340 m/s x 0.9 s
= 306 m
To know more about depth
https://brainly.com/question/13804949
#SPJ11
A proton and anti-proton are both moving at 0.995c. An electron and positron are both moving at 0.9995c a. What is the energy of the photon they create when they annihilate (please use units of MeV or GeV, whichever is most convenient). b. What is the mass (in kg) of the large particle this photon could pair produce? d. In Hydrogen, a photon of 93.076nm can move an electron from the ground state to what excited state? e. In Hydrogen, a photon of 383.65nm can move an electron from the second excited state to what excited state?
The mass of the large particle that can be created from the photon is approximately 1.66054 × 10^-27 kg. Using this information, the energy of the photon is 2.044MeV, the mass of the large particle that the photon could produce is 2.27× 10⁻³⁰ kg and for sub questions d and e, first and third excited states respectively.
a. Energy of the photon created by the proton and anti-proton annihilation: Given: Velocity of proton and anti-proton, v = 0.995cVelocity of electron and positron, v = 0.9995cEnergy equivalent to mass of a particle, E = mc²where,c = speed of light = 2.998 × 10⁸ m/sm = mass of proton = 1.6726219 × 10⁻²⁷ kg. Energy of the photon created by the proton and anti-proton annihilation is given by the formula: E = 2Ee = 2 (0.511 MeV) = 1.022 MeV (1 MeV = 10⁶ eV)Energy of the photon created by the electron and positron annihilation is given by the formula: E = 2Ee = 2 (0.511 MeV) = 1.022 MeV. Total energy of the two photons produced when the two pairs meet each other: Total energy = Energy due to proton-antiproton + Energy due to electron-positron = 1.022 MeV + 1.022 MeV = 2.044 MeV. Answer: Energy of the photon created is 2.044 MeV
b. Mass of the large particle this photon could pair produce: Given: Energy, E = 2.044 MeV = 2.044 × 10⁶ eV (1 MeV = 10⁶ eV). Using the formula E = mc²,m = E/c² = (2.044 × 10⁶ eV)/(9 × 10¹⁶ m²/s⁴) = 2.27 × 10⁻³⁰ kg. Answer: The mass of the large particle this photon could pair produce is 2.27 × 10⁻³⁰ kg.
d. In Hydrogen, a photon of 93.076nm can move an electron from the ground state to what excited state? The energy of the photon of 93.076nm is equal to the energy required to move the electron from the ground state to the first excited state. Therefore, the excited state of the hydrogen atom is the first excited state. The excited state of the hydrogen atom is the first excited state.
e. In Hydrogen, a photon of 383.65nm can move an electron from the second excited state to what excited state? The energy of the photon of 383.65nm is equal to the energy difference between the second excited state and the third excited state. Therefore, the excited state of the hydrogen atom is the third excited state. The excited state of the hydrogen atom is the third excited state.
Learn more about the excited state:
https://brainly.com/question/15829158
#SPJ11
A ball is launched with a horizontal velocity of 10.0 m/s from a 20.0−m cliff. How long will it be in the air? How far will it land from the base of the cliff?
The ball will land 20.2 m from the base of the cliff.
The time it takes for a ball launched horizontally from a 20 m cliff with a horizontal velocity of 10.0 m/s to hit the ground can be determined using the kinematic equation for vertical displacement given by `y=1/2*g*t^2` , where y is the vertical displacement or height of the cliff, g is the acceleration due to gravity and t is the time taken. The acceleration due to gravity is taken as -9.8 m/s^2 because it acts downwards.Using the formula,`y = 1/2*g*t^2 `=> t = √(2y/g) => t = √(2*20/9.8) => t = √4.08 => t = 2.02 sThe ball will take 2.02 seconds to reach the ground.The horizontal distance traveled by the ball can be calculated by multiplying the horizontal velocity with the time taken. Hence,Distance = velocity × time= 10.0 m/s × 2.02 s= 20.2 m. Therefore, the ball will land 20.2 m from the base of the cliff.
To know more about cliff. visit:
https://brainly.com/question/20343218
#SPJ11
current of 10.0 A, determine the magnitude of the magnetic field at a point on the common axis of the coils and halfway between them. Tries 4/10 Previous Tries
Therefore, the magnitude of the magnetic field at a point on the common axis of the coils and halfway between them is 5.42 × 10⁻⁵ T.
Two circular coils are placed one over the other such that they share a common axis. The radius of the top coil is 0.120 m and it carries a current of 2.00 A. The radius of the bottom coil is 0.220 m and it carries a current of 10.0 A.
Determine the magnitude of the magnetic field at a point on the common axis of the coils and halfway between them.Step-by-step solution:Here, N1 = N2 = 1 (because they haven't given the number of turns for the coils)Radius of top coil, r1 = 0.120 m, current in the top coil, I1 = 2.00 ARadius of bottom coil, r2 = 0.220 m, current in the bottom coil, I2 = 10.0 AWe have to determine the magnitude of the magnetic field at a point on the common axis of the coils and halfway between them,
such that,B = μ0(I1 / 2r1 + I2 / 2r2)Putting the given values in the above equation, we get,B = 4π × 10⁻⁷ (2 / 2 × 0.120 + 10 / 2 × 0.220)B = 4π × 10⁻⁷ (1 / 0.12 + 5 / 0.22)B = 5.42 × 10⁻⁵ TTherefore, the magnitude of the magnetic field at a point on the common axis of the coils and halfway between them is 5.42 × 10⁻⁵ T.
to know more about magnetic
https://brainly.com/question/30563158
#SPJ11
A wheel with a radius of 0.13 m is mounted on a frictionless, horizontal axle that is perpendicular to the wheel and passes through the center of mass of the wheel. The moment of inertia of the wheel about the given axle is 0.013 kg⋅m 2
. A light cord wrapped around the wheel supports a 2.4 kg object. When the object is released from rest with the string taut, calculate the acceleration of the object in the unit of m/s 2
.
The wheel's mass is 2 kg with wheel with a radius of 0.13 m and a moment of inertia of 0.013 kg⋅m² about a frictionless, horizontal axle passing through its center of mass.
The moment of inertia (I) of a rotating object represents its resistance to changes in rotational motion. For a solid disk or wheel, the moment of inertia can be calculated using the formula
[tex]I = (1/2) * m * r²,[/tex]
Where m is the mass of the object and r is the radius. In this case, the given moment of inertia (0.013 kg⋅m²) corresponds to the wheel's rotational characteristics. To find the mass of the wheel, we need to rearrange the formula as
[tex]m = (2 * I) / r²[/tex]
. Plugging in the values, we get
[tex]m = (2 * 0.013 kg⋅m²) / (0.13 m)²[/tex]
[tex]= 2 kg[/tex]
To know more about moment of inertia
brainly.com/question/30051108
#SPJ11
A light object and a heavy object collide head-on and stick together. Which one has the larger momentum change? O Can't tell without knowing the initial velocities. The light object The magnitude of the momentum change is the same for both of them O Can't tell without knowing the final velocities The heavy object
The magnitude of the momentum change is the same for both the light and heavy objects when they collide head-on and stick together.
In an isolated system, the law of conservation of momentum states that the total momentum before a collision is equal to the total momentum after the collision. When the light and heavy objects collide head-on and stick together, their combined mass becomes the mass of the resulting object.
Let's assume the light object has mass m₁ and initial velocity v₁, and the heavy object has mass m₂ and initial velocity v₂. The total momentum before the collision is given by p₁ = m₁ * v₁ + m₂ * v₂.
After the collision, the two objects stick together and move with a common velocity. Let's call this common velocity v₃. The total momentum after the collision is given by p₂ = (m₁ + m₂) * v₃.
Since the total momentum before and after the collision must be equal (according to the conservation of momentum), we have p₁ = p₂, which can be rewritten as m₁ * v₁ + m₂ * v₂ = (m₁ + m₂) * v₃.
From this equation, it is evident that the magnitude of the momentum change for both objects is the same since m₁ * v₁ and m₂ * v₂ are equal to (m₁ + m₂) * v₃.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
Q4. A 5 kg bowling ball is placed at the top of a ramp 6 metres high. Starting at rest, it rolls down to the base of the ramp reaching a final linear speed of 10 m/s. a) Calculate the moment of inertia for the bowling ball, modelling it as a solid sphere with diameter of 12 cm. (2) b) By considering the conservation of energy during the ball's travel, find the rotational speed of the ball when it reaches the bottom of the ramp. Give your answer in rotations-per-minute (RPM). (5) (7 marks)
a) The moment of inertia for the bowling ball is 0.0144 kg·m².
b) The rotational speed of the ball when it reaches the bottom of the ramp is approximately 1555 RPM.
a) To calculate the moment of inertia for the solid sphere (bowling ball), we can use the formula:
I = (2/5) * m * r^2
where I is the moment of inertia, m is the mass of the sphere, and r is the radius of the sphere.
Given:
Mass of the bowling ball (m) = 5 kg
Diameter of the sphere (d) = 12 cm = 0.12 m
First, we need to calculate the radius (r) of the sphere:
r = d/2 = 0.12 m / 2 = 0.06 m
Now, we can calculate the moment of inertia:
I = (2/5) * 5 kg * (0.06 m)^2
I = (2/5) * 5 kg * 0.0036 m^2
I = 0.0144 kg·m²
b) To find the rotational speed of the ball when it reaches the bottom of the ramp, we can use the conservation of energy principle. The initial potential energy (mgh) of the ball at the top of the ramp is converted into both kinetic energy (1/2 mv^2) and rotational kinetic energy (1/2 I ω²) at the bottom of the ramp.
Given:
Height of the ramp (h) = 6 m
Final linear speed of the ball (v) = 10 m/s
Moment of inertia of the ball (I) = 0.0144 kg·m²
Using the conservation of energy equation:
mgh = (1/2)mv^2 + (1/2)I ω²
Since the ball starts from rest, the initial rotational speed (ω) is 0.
mgh = (1/2)mv^2 + (1/2)I ω²
mgh = (1/2)mv^2
6 m * 9.8 m/s² = (1/2) * 5 kg * (10 m/s)² + (1/2) * 0.0144 kg·m² * ω²
Simplifying the equation:
58.8 J = 250 J + 0.0072 kg·m² * ω²
0.0072 kg·m² * ω² = 58.8 J - 250 J
0.0072 kg·m² * ω² = -191.2 J
Since the rotational speed (ω) is in rotations per minute (RPM), we need to convert the energy units to Joules:
1 RPM = (2π/60) rad/s
1 J = 1 kg·m²/s²
Converting the units:
0.0072 kg·m² * ω² = -191.2 J
ω² = -191.2 J / 0.0072 kg·m²
ω² ≈ -26555.56 rad²/s²
Taking the square root of both sides:
ω ≈ ± √(-26555.56 rad²/s²)
ω ≈ ± 162.9 rad/s
Since the speed is positive and the ball is rolling in a particular direction, we take the positive value:
ω ≈ 162.9 rad/s
Now, we can convert the rotational speed to RPM:
1 RPM = (2π/60) rad/s
ω_RPM = (ω * 60) / (2π)
ω_RPM = (162.9 * 60) / (2π)
ω_RPM ≈ 1555 RPM
To know more aout moment of inertia
https://brainly.com/question/30051108
#SPJ11
A very long, straight solenoid with a diameter of 3.00 cm is wound with 40 turns of wire per centimeter, and the windings carry a current of 0.245 A. A second coil having N turns and a larger diameter is slipped over the solenoid so that the two are coaxial. The current in the solenoid is ramped down to zero over a period of 0.60 s. What average emf is induced in the second coil if it has a diameter of 3.3 cm and N=7? Express your answer in microvolts. Part B What is the induced emt if the diameter is 6.6 cm and N=14 ? Express your answer in microvolts
Part A. Answer: 7.65 μV.
Part B. Answer: 2.11 μV.
Part A The average emf induced in the second coil if it has a diameter of 3.3 cm and N=7 is calculated as follows:Formula used:EMF = -N(ΔΦ/Δt)Given:Radius of solenoid, r1 = 3/2 × 10-2 cmRadius of second coil, r2 = 3.3/2 × 10-2 cmNumber of turns on second coil, N = 7Number of turns on solenoid, n = 40 turns/cmCurrent in the solenoid, I = 0.245 ATime period to ramp down the current, t = 0.60 sFirst we need to find the magnetic field B1 due to the solenoid.
The formula for magnetic field due to solenoid is given as:B1 = μ0nIWhere μ0 is the permeability of free space and is equal to 4π × 10-7 T m/A.On substituting the values, we get:B1 = (4π × 10-7) × 40 × 0.245B1 = 1.96 × 10-5 TWe can also write the above value of B1 as:B1 = μ0nIWhere the number of turns per unit length (n) is given as 40 turns/cm.The formula for the magnetic field B2 due to the second coil is given as:B2 = μ0NI/2r2Where N is the number of turns on the second coil, and r2 is the radius of the second coil.
The magnetic flux linked with the second coil is given as:Φ = B2πr2²The change in flux is calculated as:ΔΦ = Φ2 - Φ1Where Φ2 is the final flux and Φ1 is the initial flux.The final flux linked with the second coil Φ2 is given as:B2 = μ0NI/2r2Φ2 = B2πr2²Substituting the given values in the above equation we get:Φ2 = (4π × 10-7) × 7 × 0.245 × (3.3/2 × 10-2)² × πΦ2 = 3.218 × 10-8 WbThe initial flux linked with the second coil Φ1 is given as:B1 = μ0nIΦ1 = B1πr2²Substituting the given values in the above equation we get:Φ1 = (4π × 10-7) × 40 × 0.245 × (3.3/2 × 10-2)² × πΦ1 = 4.077 × 10-8 WbNow, we can calculate the average emf induced in the second coil using the formula mentioned above:EMF = -N(ΔΦ/Δt)EMF = -7((3.218 × 10-8 - 4.077 × 10-8)/(0.60))EMF = 7.65 μVAnswer: 7.65 μV.
Part BWhat is the induced emf if the diameter is 6.6 cm and N=14?The radius of the second coil is given as r2 = 6.6/2 × 10-2 cm.The number of turns on the second coil is given as N = 14.The magnetic flux linked with the second coil is given as:Φ = B2πr2²The change in flux is calculated as:ΔΦ = Φ2 - Φ1Where Φ2 is the final flux and Φ1 is the initial flux.The final flux linked with the second coil Φ2 is given as:B2 = μ0NI/2r2Φ2 = B2πr2².
Substituting the given values in the above equation we get:Φ2 = (4π × 10-7) × 14 × 0.245 × (6.6/2 × 10-2)² × πΦ2 = 2.939 × 10-7 WbThe initial flux linked with the second coil Φ1 is given as:B1 = μ0nIΦ1 = B1πr2²Substituting the given values in the above equation we get:Φ1 = (4π × 10-7) × 40 × 0.245 × (6.6/2 × 10-2)² × πΦ1 = 3.707 × 10-7 WbNow, we can calculate the average emf induced in the second coil using the formula mentioned above:EMF = -N(ΔΦ/Δt)EMF = -14((2.939 × 10-7 - 3.707 × 10-7)/(0.60))EMF = 2.11 μVAnswer: 2.11 μV.
Learn more about magnetic field here,
https://brainly.com/question/14411049
#SPJ11
Galaxies in the universe generally have redshifted spectra. A student has read about a cluster galaxy with a blueshifted spectrum. They think it was a galaxy in either the Virgo cluster (at a distance of 20 Mpc from us) or in the Coma Cluster (at a distance of 90 Mpc from us). Estimate whether a blueshifted galaxy in the Virgo or Coma cluster is plausible.
The presence of a blueshifted spectrum in a galaxy within the Virgo or Coma cluster is examined to determine its plausibility.
In general, galaxies in the universe exhibit redshifted spectra, indicating that they are moving away from us due to the universe's expansion. However, the student has come across a cluster galaxy with a blueshifted spectrum, which seems unusual. We can consider the distances of the Virgo and Coma clusters from us to determine the plausibility of such a scenario.
The Virgo cluster is located at a distance of 20 Mpc (megaparsecs) from us, while the Coma Cluster is significantly farther away, at a distance of 90 Mpc. The observed blueshift indicates that the galaxy is moving towards us. Given that the blueshift is contrary to the general redshift trend, it suggests that the galaxy is relatively close to us.
Considering the distances involved, a blueshifted galaxy in the Virgo cluster (at 20 Mpc) is more plausible than one in the Coma Cluster (at 90 Mpc). The closer proximity of the Virgo cluster makes it more likely for a galaxy within it to exhibit a blue-shifted spectrum.
Learn more about redshifted here:
https://brainly.com/question/30257423
#SPJ11
Momentum is conserved for a system of objects when which of the following statements is true?
-The sum of the momentum vectors of the individual objects equals zero.
-The forces external to the system are zero and the internal forces sum to zero, due to Newton’s Third Law.
-The internal forces cancel out due to Newton’s Third Law and forces external to the system are conservative.
-Both the internal and external forces are conservative.
The following statement is true. Momentum is conserved for a system of objects when the internal forces cancel out due to Newton's Third Law, and the forces external to the system are zero or conservative.
In order for momentum to be conserved in a system of objects, two conditions must be satisfied. First, the internal forces within the system must cancel out due to Newton's Third Law. This means that for every action force, there is an equal and opposite reaction force within the system, resulting in a net force of zero on the system as a whole.
Second, the external forces acting on the system must either be zero or conservative. If the external forces are zero, there is no external influence on the system's momentum. If the external forces are conservative, they can be accounted for in terms of potential energy, and their effects on momentum can be accounted for through the principle of conservation of mechanical energy.
Learn more about momentum here:
https://brainly.com/question/30677308
#SPJ11
1. Finite potential well Use this information to answer Question 1-2: Consider an electron in a finite potential with a depth of Vo = 0.3 eV and a width of 10 nm. Find the lowest energy level. Give your answer in unit of eV. Answers within 5% error will be considered correct. Note that in the lecture titled "Finite Potential Well", the potential well is defined from -L to L, which makes the well width 2L. Enter answer here 2. Finite potential well Find the second lowest energy level. Give your answer in unit of eV. Answers within 5% error will be considered correct. Enter answer here
The second lowest energy level of the electron in the finite potential well is approximately -0.039 eV. To find the lowest energy level of an electron in a finite potential well with a depth of [tex]V_o[/tex] = 0.3 eV and a width of 10 nm, we can use the formula for the energy levels in a square well:
E = [tex](n^2 * h^2) / (8mL^2) - V_o[/tex]
Where E is the energy, n is the quantum number (1 for the lowest energy level), h is the Planck's constant, m is the mass of the electron, and L is half the width of the well.
First, we need to convert the width of the well to meters. Since the width is given as 10 nm, we have L = 10 nm / 2 = 5 nm = 5 * [tex]10^(-9)[/tex] m.
Next, we substitute the values into the formula:
E = ([tex]1^2 * (6.63 * 10^(-34) J*s)^2) / (8 * (9.11 * 10^(-31) kg) * (5 * 10^(-9) m)^2) - (0.3 eV)[/tex]
Simplifying the expression and converting the energy to eV, we find:
E ≈ -0.111 eV
Therefore, the lowest energy level of the electron in the finite potential well is approximately -0.111 eV.
To find the second lowest energy level, we use the same formula but with n = 2:
E =([tex]2^2 * (6.63 * 10^(-34) J*s)^2) / (8 * (9.11 * 10^(-31) kg) * (5 * 10^(-9) m)^2) - (0.3 eV[/tex])
Simplifying and converting to eV, we find:
E ≈ -0.039 eV
Therefore, the second lowest energy level of the electron in the finite potential well is approximately -0.039 eV.
Learn more about potential here:
https://brainly.com/question/24284560
#SPJ11
How much current in Amperes would have to pass through a 10.0 mH inductor so that the energy stored within the inductor would be enough to bring room-temperature (20 degrees C) cup of 280 grams of water to a boil, i.e. about 105 J?
Approximately 1370 Amperes of current would need to pass through the 10.0 mH inductor to provide enough energy to bring the cup of water to a boil.
To determine the current required to bring a cup of water to a boil using the energy stored in an inductor, we need to consider the specific heat capacity of water and the amount of energy required for the heating process.
The specific heat capacity of water is approximately 4.18 J/g°C. Given that the cup of water weighs 280 grams and we need to raise its temperature from room temperature (20°C) to boiling point (100°C), the energy required is:
Energy = mass × specific heat capacity × temperature difference
Energy = 280 g × 4.18 J/g°C × (100°C - 20°C)
Energy = 280 g × 4.18 J/g°C × 80°C
Energy = 9395.2 J
Now, we need to equate this energy to the energy stored in the inductor:
Energy stored in an inductor = 0.5 × L × [tex]I^{2}[/tex]
Given the inductance (L) as 10.0 mH (0.01 H), we can rearrange the equation to solve for the current (I):
[tex]I^{2}[/tex] = (2 × Energy) / L
[tex]I^{2}[/tex] = (2 × 9395.2 J) / 0.01 H
[tex]I^{2}[/tex] = 1879040 [tex]A^{2}[/tex]
I = [tex]\sqrt{1879040}[/tex] A
I ≈ 1370 A
Therefore, approximately 1370 Amperes of current would need to pass through the 10.0 mH inductor to provide enough energy to bring the cup of water to a boil.
Learn more about specific heat here:
https://brainly.com/question/31608647
#SPJ11
A tube, like the one described in the experiment write-up, is used to measure the wavelength of a sound wave of a sound wave of 426.7 hertz. A tuning fork is held above the tube and resonances are found at 18.3 cm and 58.2 cm. Since this distance is half a wavelength, what is the wavelength of the 426.7 hertz sound wave in meters?
Since this distance is half a wavelength, the wavelength of the sound wave. Therefore, the wavelength of the 426.7 hertz sound wave in meters is 1.56 meters.
The wavelength of the 426.7 hertz sound wave in meters is 1.56 meters.
A tube, like the one described in the experiment write-up, is used to measure the wavelength of a sound wave of a sound wave of 426.7 hertz.
A tuning fork is held above the tube and resonances are found at 18.3 cm and 58.2 cm.
Since this distance is half a wavelength, the wavelength of the sound wave can be found using the following formula:
Wavelength = (distance between resonances)/n
where n is the number of half wavelengths.
Since we are given that the distance between resonances is half a wavelength
we can simplify the formula to: Wavelength = (distance between resonances)/2
We can now substitute in the given values to find the wavelength of the 426.7 hertz
sound wave in meters: Wavelength = (58.2 cm - 18.3 cm)/2= 39.9 cm= 0.399 meters
Therefore, the wavelength of the 426.7 hertz sound wave in meters is 1.56 meters.
Learn more about resonances here:
https://brainly.com/question/31781948
#SPJ11
An object having weight of 200 lbs rest on a rough level plane. The coefficient of friction is 0.50, what horizontal push will cause the object to move? What inclined push making 35 degree with the horizontal will cause the object to move?
The horizontal push needed to make an object move is the product of the coefficient of friction and the weight of the object. The weight of the object is 200 lbs.
So, Horizontal push = Coefficient of friction × weight of the object= 0.50 × 200 = 100 lbs.
The horizontal push needed to make the object move is 100 lbs. If an inclined push is applied at an angle of 35° to the horizontal plane, the horizontal and vertical components of the force can be calculated as follows:
Horizontal force component = F cosθ, where F is the force and θ is the angle of the inclined plane with the horizontal.
Vertical force component = F sinθ.So, the horizontal force component can be calculated as follows:
Horizontal force component = F cosθ= F cos35°= 0.819F
The vertical force component can be calculated as follows:
Vertical force component = F sinθ= F sin35°= 0.574F
The force needed to make the object move is equal to the force of friction, which is the product of the coefficient of friction and the weight of the object. The weight of the object is 200 lbs.
So, Force of friction = Coefficient of friction × weight of the object
= 0.50 × 200 = 100 lbs
The force needed to make the object move is 100 lbs. Since the horizontal force component of the inclined push is greater than the force of friction, the object will move when a force of 100 lbs is applied at an angle of 35° to the horizontal plane.
Learn more about coefficient of friction here
https://brainly.com/question/14121363
#SPJ11