The magnitude of tension T2 is 18 N.
In the given figure, three bodies of masses m1=6 kg and m2=m3=12 kg are connected. And, they are pulled towards right on a frictionless surface. If the magnitude of tension T3 is 60 N, then we need to determine the magnitude of tension T2.Let's consider the acceleration of the system, which is common to all three masses. So, for m1,m2, and m3, we have equations as follows:6a = T2 - T112a = T3 - T216a = T2 + T3By solving above equations, we get T2 = 18 N. Hence, the magnitude of tension T2 is 18 N.
To know more about horizontal visit:
https://brainly.com/question/31166587
#SPJ11
In a baseball game, a batter hits the 0.150−kg ball straight Part A back at the pitcher at 190 km/h. If the ball is traveling at 150 km/h just before it reaches the bat, what is the magnitude of the average force exerted by the bat on it if the collision lasts 6.0 ms ? Express your answer with the appropriate units.
The magnitude of the average force exerted by the bat on the ball is approximately 1,500 N.
To find the magnitude of the average force exerted by the bat on the ball, we can use the impulse-momentum principle. The impulse experienced by an object is equal to the change in momentum it undergoes. In this case, the change in momentum of the ball is given by:
Δp = m * Δv, where Δp is the change in momentum, m is the mass of the ball, and Δv is the change in velocity. The initial velocity of the ball is 150 km/h, and the final velocity is -190 km/h (since it is traveling back towards the pitcher). Converting these velocities to m/s, we have: Initial velocity: 150 km/h = 41.7 m/s. Final velocity: -190 km/h = -52.8 m/s.
The change in velocity, Δv, is then (-52.8 m/s) - (41.7 m/s) = -94.5 m/s. Substituting the values into the equation for impulse, we have: Impulse = m * Δv = (0.150 kg) * (-94.5 m/s) = -14.18 kg·m/s. The magnitude of the average force, F, can be calculated using the equation: F = Δp / Δt, where Δt is the time interval of the collision.
Substituting the values, we have: F = (-14.18 kg·m/s) / (6.0 ms) = -2,363 N.
Learn more about force here:
https://brainly.com/question/13191643
#SPJ11
A parallel plate capacitor with circular faces of diameter 3.8 cm separated with an air gap of 3.8 mm is charged with a 12,0 V emf. What is the capacitance of this device, in pF, between the plates? Do not enter units with answer
The capacitance (C) of a parallel plate capacitor can be calculated using the formula: C = (ε₀ * A) / d. (ε₀ ≈ 8.854 x 10^(-12) F/m), A is area of one circular face of capacitor (A = π * (r^2)), d is distance between plates.
EMF (V) = 12.0 V.
C = (ε₀ * A) / d = (8.854 x 10^(-12) F/m * π * (0.019 m)^2) / 0.0038 m
C ≈ 1.49 pF
The capacitance of the parallel plate capacitor is approximately 1.49 pF.
A capacitor is an electronic component that stores electrical energy in an electric field. It consists of two conductive plates separated by an insulating material known as a dielectric. When a voltage is applied across the plates, the capacitor charges up, storing energy. Capacitors are commonly used in electronic circuits for energy storage, filtering, timing, and coupling signals. They are characterized by their capacitance, which measures the amount of charge a capacitor can store per unit voltage.
Learn more about capacitor here:
https://brainly.com/question/30732711
#SPJ11
How can we prepare a cavity with a photon? (I.e., make sure that exactly one photon exists in the cavity.)
We can prepare a cavity with a photon by applying a short optical pulse to excite an atom and using Rabi oscillation to control the interaction between the atom and a photon in a cavity.
To prepare cavity with a photon, we need to follow some steps. They are:Start with the cavity and prepare it in the ground state.To excite the atom, apply a short optical pulse.A photon will be produced by the atom and will enter the cavity if the atom is in the excited state.The photon will be trapped in the cavity and can be measured.To make sure that exactly one photon exists in the cavity, we can use the process of Rabi oscillation. It involves an atom and a photon in a resonant cavity.
When the photon is absorbed by the atom, the system's state changes to an excited state, and this energy is released in the form of a photon.The Rabi oscillation is a way to control and manipulate the interaction between an atom and a photon in a cavity, and it can be used to prepare a cavity with exactly one photon. By tuning the parameters of the pulse, we can control the probability of a photon being produced by the atom and entering the cavity, allowing us to prepare a cavity with a single photon.Therefore, we can prepare a cavity with a photon by applying a short optical pulse to excite an atom and using Rabi oscillation to control the interaction between the atom and a photon in a cavity.
Learn more about Manipulate here,how does manipulation solve the third-variable problem?
https://brainly.com/question/30775783
#SPJ11
Two stationary point charges experience a mutual electric force of magnitude 108 N. Subsequently, if the distance between the two point charges is tripled while the magnitude of both charges is cut in half.
What is the magnitude of the resultant electric force on either charge?
a. 6.0 N
b. 3.0 N
c. 12 N
d. 9.0 N
e. 27 N
The correct answer the magnitude of the resultant electric force on either charge is Option d.9.0 N
Let the original magnitude of one charge be q1 and the original magnitude of the other charge be q2. The original distance between the two charges is r.
The magnitude of the force between two point charges q1 and q2 is given by Coulomb's law as:F=kq1q2/r²Where k is Coulomb's constant which is 9 × 10^9 Nm²/C².Subsequently, if the distance between the two point charges is tripled while the magnitude of both charges is cut in half, the new distance between the two charges is 3r and the new magnitude of both charges is (1/2)q.
The force between the two charges with the new conditions is given by:F'=k((1/2)q)(1/2)q/(3r)²F'=kq²/27r²Since the magnitude of the force between two stationary point charges is the same for each charge, the magnitude of the resultant electric force on either charge is given by:F''=F'/2F''=kq²/54r²The ratio of the new force to the old force is:F''/F=kq/108r².
The magnitude of the force on each charge is:F1=F2=F''/2F1=F2=kq²/108r²The magnitude of the force on each charge is kq²/108r². Answer: d. 9.0 N.
Learn more about electric force here,
https://brainly.com/question/30236242
#SPJ11
Required information While testing speakers for a concert, Tomás sets up two speakers to produce sound waves at the same frequency, which is between 100 Hz and 150 Hz. The two speakers vibrate in phase with each other. He notices that when he listens at certain locations, the sound is very soft (a minimum Intensity compared to nearby points). One such point is 26.1 m from one speaker and 373 m from the other (The speed of sound in air is 343 m/s.) What is the maximum frequency of the sound waves coming from the speakers? Hz
Given data: Distance between two speakers is d1 = 26.1m
Distance between the observer and one speaker is d2 = 373m
The speed of sound in air is v = 343m/s
The sound waves are in-phase with each other and the minimum intensity is observed at this point. This point is the position of a node of the sound wave. If we consider the path difference between the two waves to be an integer multiple of the wavelength, we will obtain another node of the wave, where the intensity is minimum.
The distance between these two points will be half the wavelength of the sound wave. Since we have two speakers and one observer, it is clear that the sound waves are propagating in 3-dimensional space.
Therefore, we will use the formula for 3-dimensional distance between two points.
We have, d1+d2 = 399.1m = (n + 1/2) λ
Where n is an integer.
We can consider the case of minimum value of n, which is 0. λ = 2 × 26.1 × 373 / 399.1λ = 47.1m
Frequency of the sound wave, v = fλ f = v / λ f = 343 / 47.1 = 7.28Hz (approx)
Therefore, the maximum frequency of the sound waves coming from the speakers is 7.28Hz (approx).
Answer: 7.28 Hz (approx)
Learn more about soundwaves, here
https://brainly.com/question/16093793
#SPJ11
A girl and her mountain bike have a total mass of 65.2 kg and 559 J of potential energy while riding on an elevated, horizontal loading dock. Starting with an initial velocity of 3.14 m/s, she rides her bike down a ramp attached to the dock and reaches the ground below.
a) What is the change in height from the top of the ramp to the ground?
b) What is the total mechanical energy at the point where the ramp meets the
ground?
D) Upon impact with the ground, the bike's front suspension compresses a
distance of 0.315 m from an average force of 223 N. What is the work done to compress the front suspension?
a) The change in height from the top of the ramp to the ground is approximately 0.50 m.b) The total mechanical energy at the point where the ramp meets the ground is zero. c) The work done to compress the front suspension is approximately 70.3 J.
a) The change in height from the top of the ramp to the groundThe initial potential energy of the girl and the mountain bike was 559 J. When the girl rode down the ramp, this potential energy was converted to kinetic energy. Therefore, the change in potential energy is the same as the change in kinetic energy. The total mass of the girl and her mountain bike is 65.2 kg. The initial velocity is 3.14 m/s. The final velocity is zero because the girl and the mountain bike come to a stop at the bottom of the ramp. Let us use the conservation of energy equation and set the initial potential energy equal to the final kinetic energy: Initial potential energy = Final kinetic energy mgh = 1/2 mv²Solve for h: h = (1/2)(v²/g)Where v is the initial velocity and g is the acceleration due to gravity (9.81 m/s²).h = (1/2)(3.14²/9.81)h ≈ 0.50 mThe change in height from the top of the ramp to the ground is approximately 0.50 m.b) The total mechanical energy at the point where the ramp meets the ground. At the point where the ramp meets the ground, the girl and the mountain bike come to a stop. Therefore, their kinetic energy is zero. Their potential energy is also zero because they are at ground level. Therefore, the total mechanical energy is also zero.c) Work done to compress the front suspension. The work done to compress the front suspension is the force applied multiplied by the distance it is applied over W = Fd, where F is the force and d is the distance. The distance the front suspension compresses is 0.315 m. The force applied is 223 N. Therefore:W = FdW = (223 N)(0.315 m)W ≈ 70.3 JFor more questions on mechanical energy
https://brainly.com/question/28154924
#SPJ8
An object is placed 45 cm to the left of a converging lens of focal length with a magnitude of 25 cm. Then a diverging lens of focal length of magnitude 15 cm is placed 35 cm to the right of this lens. Where does the final image form for this combination? Please give answer in cm with respect to the diverging lens, using the appropriate sign conventioIs the image in the previous question real or virtual?
The image distance from the diverging lens is 75.18 cm. The positive sign indicates that the image is formed to the right of the lens. Answer: The final image will form 75.18 cm to the right of the diverging lens. The image formed is virtual.
The given problem is related to the formation of the final image by using the combination of the converging and diverging lenses. Here, we have to calculate the distance of the final image from the diverging lens and we need to also mention whether the image is real or virtual. The focal length of the converging lens is 25 cm and the focal length of the diverging lens is 15 cm. The distance of the object from the converging lens is given as 45 cm.Now, we will solve the problem step-by-step.
Step 1: Calculation of image distance from the converging lensWe can use the lens formula to find the image distance from the converging lens. The lens formula is given as:1/f = 1/v - 1/uwhere, f = focal length of the lensv = distance of the image from the lensu = distance of the object from the lensIn this case, the focal length of the converging lens is f = 25 cm. The distance of the object from the converging lens is u = -45 cm (since the object is placed to the left of the lens). We have to put the negative sign because the object is placed to the left of the lens.Now, we will calculate the image distance v.v = (1/f + 1/u)-1/v = 1/25 + 1/-45 = -0.04v = -25 cm (by putting the value of 1/v in the equation)Therefore, the image distance from the converging lens is -25 cm. The negative sign indicates that the image is formed to the left of the lens.
Step 2: Calculation of distance between the converging and diverging lens Now, we have to calculate the distance between the converging and diverging lens. This distance will be equal to the distance between the image formed by the converging lens and the object for the diverging lens. We can calculate this distance as follows:Object distance from diverging lens = image distance from converging lens= -25 cm (as we have found the image distance from the converging lens in the previous step)Now, we have to calculate the distance between the object and the diverging lens. The object is placed to the right of the converging lens. Therefore, the distance of the object from the diverging lens will be:Distance of object from diverging lens = Distance of object from converging lens + Distance between the two lenses= 45 cm + 35 cm= 80 cm Therefore, the distance of the object from the diverging lens is 80 cm.
Step 3: Calculation of image distance from the diverging lensWe can again use the lens formula to calculate the image distance from the diverging lens. This time, the object is placed to the right of the diverging lens, and the lens is diverging in nature. Therefore, the object distance and the focal length of the lens will be positive. The lens formula in this case is given as:1/f = 1/v - 1/uwhere, f = focal length of the lensv = distance of the image from the lensu = distance of the object from the lensIn this case, the focal length of the diverging lens is f = -15 cm (since it is diverging in nature).
The distance of the object from the diverging lens is u = 80 cm.Now, we will calculate the image distance v.v = (1/f + 1/u)-1/v = 1/-15 + 1/80 = 0.0133v = 75.18 cm (by putting the value of 1/v in the equation)Therefore, the image distance from the diverging lens is 75.18 cm. The positive sign indicates that the image is formed to the right of the lens. Answer: The final image will form 75.18 cm to the right of the diverging lens. The image formed is virtual.
Learn more about Equation here,
https://brainly.com/question/29174899
#SPJ11
How would the intensity of sunlight at Earth's surface change if Earth were 1.5 times farther from the sun than it is currently?
Increase by a factor of 1.5.
Decrease by a factor of 2.25.
Increase by a factor of 2.25.
Decrease by a factor of 1.5.
Remain unchanged.
if Earth were 1.5 times farther from the sun, the intensity of sunlight at Earth's surface would decrease by a factor of 2.25, resulting in a significant reduction in the amount of sunlight reaching the surface. So, the correct answer is Decrease by a factor of 2.25.
If Earth were 1.5 times farther from the sun than its current distance, the intensity of sunlight at Earth's surface would decrease by a factor of 2.25. This change in intensity can be explained by the inverse square law, which states that the intensity of light is inversely proportional to the square of the distance from the source.
According to the inverse square law, if the distance between Earth and the sun increases by a factor of 1.5, the intensity of sunlight would decrease by the square of that factor, which is (1.5)² = 2.25. This means that the intensity of sunlight would be reduced to 1/2.25 or approximately 44.4% of its original value.
The reason for this decrease in intensity is that as the distance between Earth and the sun increases, the same amount of sunlight is spread out over a larger area. Consequently, the energy per unit area, which determines the intensity, decreases.
Therefore, if Earth were 1.5 times farther from the sun, the intensity of sunlight at Earth's surface would decrease by a factor of 2.25, resulting in a significant reduction in the amount of sunlight reaching the surface.
Learn more about intensity
https://brainly.com/question/31763343
#SPJ11
If the exposure rate constant is 0. 87 Rcm2/mCi-hr and the average patient transmission factor is 0. 2, the exposure rate mR/hr. At 12. 5 cm for a patient who has been injected with 20 mCi of Tc-99m is 22 21 20 19
Answer:
To find the exposure rate (in mR/hr) at a distance of 12.5 cm, we can use the following equation:
Exposure Rate (mR/hr) = Exposure Rate Constant (Rcm²/mCi-hr) × Activity (mCi) × Transmission Factor / Distance² (cm²)
Plugging in the given values:
Exposure Rate (mR/hr) = 0.87 Rcm²/mCi-hr × 20 mCi × 0.2 / (12.5 cm)²
Exposure Rate (mR/hr) = 17.4 Rcm²/hr × 0.2 / 156.25 cm²
Exposure Rate (mR/hr) = 3.48 Rcm²/hr / 156.25 cm²
Exposure Rate (mR/hr) ≈ 0.0223 R/hr
Since 1 R (Roentgen) is equal to 1000 mR (milliroentgen), we can convert the exposure rate to mR/hr:
Exposure Rate (mR/hr) ≈ 0.0223 R/hr × 1000 mR/R
Exposure Rate (mR/hr) ≈ 22.3 mR/hr
The closest answer choice is:
A) 22
A car initially traveling eastward turns north by traveling in a circular path at a uniform speed as shown in the figure below. The length of the arc ABC is 222 m, and the car completes the turn in 34.0 s.
An x y coordinate axis is shown. Point A is located at a negative value on the y-axis, and an arrow points from the point A to the right. A dotted line curves up and to the right in a quarter circle until it reaches point C on the positive x-axis. An arrow points directly upward from point C. Point B is on the dotted circle. A line drawn from the origin to point B makes an angle of 35.0° below the x-axis.
(a) Determine the car's speed.
m/s
(b) What is the magnitude and direction of the acceleration when the car is at point B?
magnitude m/s2
direction ° counterclockwise from the +x-axis
A car initially traveling eastward turns north in a circular path, covering an arc length of 222 m in 34.0 s. A line drawn from the origin to point B makes an angle of 35.0° below the x-axis. The speed of the car is 6.53 m/s and acceleration at B is [tex]0.336 m/s^2[/tex].
(a) To determine the car's speed, we can use the formula v = s/t, where v represents the velocity (speed), s represents the distance traveled, and t represents the time taken. In this case, the distance traveled is the length of the arc ABC, which is given as 222 m, and the time taken is given as 34.0 s. Substituting these values into the formula, we have:
v = [tex]\frac{ 222 }{34}[/tex] = [tex]6.53 m/s[/tex]
Therefore, the car's speed is [tex]6.53 m/s.[/tex]
(b) To find the magnitude of the acceleration at point B, we can use the formula a = [tex]v^2 / r[/tex], where a represents acceleration, v represents velocity, and r represents the radius of the circular path. From the given figure, we can see that the radius of the circular path is the distance from the origin to point B.
Using trigonometry, we can find the radius as follows:
r = BC = AB * [tex]sin(35°) = 222 m * sin(35°)[/tex] ≈ [tex]126.83 m[/tex]
Substituting the values into the formula, we have:
a = [tex](6.53 m/s)^2[/tex] / [tex]126.83 m[/tex] ≈ [tex]0.336 m/s^2[/tex]
Therefore, the magnitude of the acceleration at point B is approximately [tex]0.336 m/s^2[/tex].
(c) To determine the direction of the acceleration, we need to consider the circular motion. At point B, the acceleration is directed towards the center of the circle. Since the car is turning from east to north, the direction of the acceleration would be counterclockwise. The angle between the acceleration and the +x-axis can be determined as follows:
Angle = [tex]90° - 35° = 55°[/tex]
Therefore, the direction of the acceleration at point B is approximately 55° counterclockwise from the +x-axis.
Learn more about acceleration here:
https://brainly.com/question/30660316
#SPJ11
A cube is 2.0 cm on a side when at rest. (a) What shape does it
take on when moving past an observer at 2.5 x 10^8 m/s, and (b)
what is the length of each side?
Answer: The length of each side of the cube when moving past an observer at 2.5 x 10^8 m/s is 1.22 cm.
The question is asking us to consider the relativistic effect of time dilation and length contraction, which affect the measurement of distance and time by a moving observer. Therefore, the apparent length and shape of the cube will differ from the actual measurements as seen by an observer at rest.
a) When the cube moves past an observer at a velocity of 2.5 x 10^8 m/s, it takes on a shape that is flattened in the direction of motion. This is because of the relativistic effect of length contraction. This effect states that the length of an object appears shorter to an observer in motion than to an observer at rest.
The degree of length contraction increases with velocity and is given by the formula: L' = L₀ / γ
where L₀ is the length at rest, L' is the apparent length observed by a moving observer, and γ is the Lorentz factor given by :
γ = 1 / √(1 - v²/c²) where v is the velocity of the cube and c is the speed of light.
Substituting the values, we have:
L' = 2.0 cm / γL'
= 2.0 cm / √(1 - (2.5 x 10^8 m/s)²/(3.0 x 10^8 m/s)²)L'
= 0.47 cm.
b) The length of each side of the cube when moving past an observer at 2.5 x 10^8 m/s is given by: L' = L₀ / γL = L' x γSubstituting the values, we have:
L = L' x γL
= 0.47 cm x √(1 - (2.5 x 10^8 m/s)²/(3.0 x 10^8 m/s)²)L
= 1.22 cm.
Thus, the length of each side of the cube when moving past an observer at 2.5 x 10^8 m/s is 1.22 cm.
Learn more about time dilation : https://brainly.com/question/3747871
#SPJ11
5 ed led c) Convert 15 bar pressure into in. Hg at 0 °C.
Therefore,15 x 0.987 = 14.81 in. Hg (Approximately)Hence, the pressure in in. Hg at 0°C is 14.81.
The given value is 15 bar pressure. We have to convert this value into in. Hg at 0°C. In order to convert the given value, we need to have a conversion table.
Conversion of pressure units: 1 atm = 760 mm Hg = 29.92 in Hg = 101325 N/m2 = 101.325 kPa We can use this table to convert the given value of pressure into in. Hg at 0°C. Now, we can use the following formula to calculate the pressure in in. Hg at 0°C: bar x 0.987 = in. Hg at 0°CBy substituting the value of bar from the given data, we get the value of pressure in in. Hg at 0°C. Therefore,15 x 0.987 = 14.81 in. Hg (Approximately)Hence, the pressure in in. Hg at 0°C is 14.81.
To know more about pressure of a gas visit:
https://brainly.com/question/23026422
#SPJ11
A 0.199 kg particle with an initial velocity of 2.72 m/s is accelerated by a constant force of 5.86 N over a distance of 0.227 m. Use the concept of energy to determine the final velocity of the particle. (It is useful to double-check your answer by also solving the problem using Newton's Laws and the kinematic equations.) Please enter a numerical answer below. Accepted formats are numbers or "e" based scientific notation e.g. 0.23, -2, 146, 5.23e-8 Enter answer here m/s
By using the concept of energy, the final velocity of the particle is obtained approximately as 4.548 m/s.
To determine the final velocity of the particle using the concept of energy, we can apply the work-energy principle.
The work done on an object is equal to the change in its kinetic energy.
The work done on the particle is given by the formula:
Work = Force * Distance * cos(θ)
In this case, the force is 5.86 N and the distance is 0.227 m.
Since the angle θ is not provided, we will assume that the force is applied in the direction of motion, so cos(θ) = 1.
Work = 5.86 N * 0.227 m * 1 = 1.33162 N·m
The work done on the particle is equal to the change in its kinetic energy.
The initial kinetic energy is given by:
Initial Kinetic Energy = (1/2) * mass * initial velocity^2
Initial Kinetic Energy = (1/2) * 0.199 kg * (2.72 m/s)^2
Initial Kinetic Energy = 0.7319296 J
The final kinetic energy is given by:
Final Kinetic Energy = Initial Kinetic Energy + Work
Final Kinetic Energy = 0.7319296 J + 1.33162 N·m
Final Kinetic Energy = 2.0635496 J
Finally, we can determine the final velocity using the equation:
Final Kinetic Energy = (1/2) * mass * final velocity^2
2.0635496 J = (1/2) * 0.199 kg * final velocity^2
[tex](final \,velocity)^2[/tex] = 2.0635496 J / (0.199 kg * (1/2))
[tex](final \,velocity)^2[/tex] = 20.718592 J/kg
final velocity = [tex]\sqrt{20.718592 J/kg}[/tex] = 4.548 m/s
Therefore, the final velocity of the particle is approximately 4.548 m/s.
Learn more about energy here:
https://brainly.com/question/3347851
#SPJ11
A0.38-kg stone is droppod from rest at a height of 0.92 m above the floor. Afcer the stone hits the floos, it bounces upwards at 92.5% of the inpact speed. What is the magnitude of the stone's change in moenentum?
Stone weighing 0.38 kg is dropped from rest at a height of 0.92 meters above the floor. After the stone hits the floor, it bounces upwards at 92.5% of the impact speed. Therefore, The magnitude of the stone's change in momentum is 5.16 kg m/s.
Momentum is the product of mass and velocity. The product of mass and velocity gives you momentum.
This is represented by p = mv.
The formula for calculating the change in momentum is:Δp = pf − pi
where Δp represents the change in momentum, pf is the final momentum, and pi is the initial momentum
problem A stone weighing 0.38 kg is dropped from rest at a height of 0.92 meters above the floor.
After the stone hits the floor, it bounces upwards at 92.5% of the impact speed.
Impact speed is the speed at which the stone hits the floor.
The impact speed of the stone can be calculated using the formula :v = sqrt(2gh)
where v is the impact speed, g is acceleration due to gravity (9.8 m/s²), and h is the height from which the stone is dropped from rest.
The impact speed of the stone is:v = sqrt(2gh)v = sqrt(2 × 9.8 m/s² × 0.92 m)v = 3.38 m/s
The velocity of the stone after it bounces back up is 92.5% of its impact speed. Therefore, the velocity of the stone after it bounces back up is:v′ = 0.925v′ = 0.925 × 3.38 m/sv′ = 3.12 m/s
The magnitude of the initial momentum is:p0 = mv0p0 = 0.38 kg × 0p0 = 0 kg m/s
The magnitude of the final momentum is:p = mvp = 0.38 kg × 3.12 m/sp = 1.18 kg m/sΔp = pf − piΔp = 1.18 kg m/s − 0 kg m/sΔp = 1.18 kg m/s
Therefore, The magnitude of the stone's change in momentum is 5.16 kg m/s.
Learn more about initial momentum here:
https://brainly.com/question/12450698
#SPJ11
Here is a graph of my dog walking in my yard. a. What is the dog's displacement after 5 s ? b. What is the dog's distance travelled after 5 s ? c. At what position (if any) is the dog stopped? d. What is the dog's velocity at t=4 s ?
a. The dog's displacement after 5 seconds is equal to the change in position. To determine this, we must determine the distance between the final position and the initial position.
The dog's initial position was zero, and its final position was 1 meter west (negative direction), so the displacement is equal to 1 meter in the negative direction.
Displacement = final position - initial position = -1 m - 0 m = -1 m.
b.
The distance traveled is the total distance covered by the dog. We must determine the sum of the magnitudes of each vector quantity in this case. The displacement from the previous part was equal to 1 m, but we must now account for the distance that the dog covered in the positive direction (east) before moving back west. 2 m + 1 m = 3 m total distance covered. The dog's distance traveled after 5 seconds is equal to 3 meters.
c. The dog is motionless when its position remains constant. The dog is stationary between 2 and 3 seconds because the graph is flat. The dog is not in any position when it is stopped.
d.
Velocity is defined as the rate at which the position changes over time. If the position increases over time, the velocity is positive, whereas if the position decreases over time, the velocity is negative.
When the position remains constant, the velocity is zero. The graph is flat between 2 and 3 seconds, so the velocity is zero. When the dog is at a position of 1 meter west of the origin at 5 seconds, the dog's velocity is calculated as follows:
Velocity = displacement/time = (-1 m - 0 m) / (5 s - 0 s) = -1/5 m/s.
The dog's velocity at t = 4 s is -1/5 m/s.
To learn about velocity here:
https://brainly.com/question/80295
#SPJ11
An emf is induced in a conducting loop of wire 1.03 Part A m long as its shape is changed from square to circular. Find the average magnitude of the induced emf if the change in shape occurs in 0.165 s and the local 0.438 - T magnetic field is perpendicular to the plane of the loop.
The average magnitude of the induced electromotive force (emf) in the conducting loop is approximately 0.497 V when it changes from a square shape to a circular shape in 0.165 s.
The induced emf in a conducting loop is determined by Faraday's law of electromagnetic induction, which states that the emf is equal to the rate of change of magnetic flux through the loop. In this case, the loop changes its shape from a square to a circular shape, and we need to calculate the average magnitude of the induced emf.
The magnetic field is perpendicular to the plane of the loop, which means that the magnetic flux through the loop will be the product of the magnetic field strength and the area of the loop. As the loop changes its shape, the area of the loop also changes.
Initially, when the loop is square, the area is given by A = [tex](1.03m)^{2}[/tex]. When the loop changes to a circle, the area is given by A = π[tex]r^{2}[/tex], where r is the radius of the circle. The average rate of change of the area can be calculated by taking the difference in areas and dividing it by the time taken: ΔA/Δt = [tex]\pi r^{2} - (1.03m)^{2}[/tex] / 0.165 s.
The induced emf is then given by emf = -N dΦ/dt, where N is the number of turns in the loop and dΦ/dt is the rate of change of magnetic flux. In this case, N is assumed to be 1. Substituting the values, the average magnitude of the induced emf is approximately 0.497 V.
Learn more about emf here:
https://brainly.com/question/30893775
#SPJ11
Write a discussion and analysis about. the half-wave rectifier ofg the operation
A half-wave rectifier is an electronic circuit that converts the positive half-cycle or the negative half-cycle of an alternating current signal to a pulsating direct current signal. It allows the current to flow in only one direction by removing half of the signal. A half-wave rectifier is less effective than a full-wave rectifier, which utilizes both the positive and negative halves of the AC signal.
The following is a discussion and analysis of the half-wave rectifier operation.
Discussion-
Half-wave rectifiers are frequently used in DC power supply circuits. The fundamental purpose of rectification is to convert AC to DC. Rectifiers may be used to power a variety of electronic devices, ranging from simple battery-powered gadgets to high-voltage power supplies.
During the positive half-cycle of the input AC signal, the diode is forward-biased, allowing current to flow. The load is consequently supplied with a current flow in one direction only. The diode is reverse-biased during the negative half-cycle of the input AC signal, preventing the current from flowing.
The output voltage is unidirectional and has a pulsating nature as a result of this half-wave rectification. It means that, at the beginning of each half-cycle, the output voltage starts from zero and then grows to a peak value until the half-cycle ends.
Analysis:
A half-wave rectifier's output voltage is not pure DC since it contains a lot of ripples. To reduce ripple, an input filter capacitor can be used to smooth the voltage waveform. The resulting waveform is smoothed out and closer to pure DC. As a result, a half-wave rectifier has the following characteristics:
-The maximum voltage is only half the peak input voltage.
-The DC output voltage is pulsating, with a considerable ripple.
-The efficiency of a half-wave rectifier is around 40-50%.
-The half-wave rectifier has a low cost and simple design.
The half-wave rectifier circuit is simple and requires only a single diode. As a result, it is less expensive and more straightforward than a full-wave rectifier circuit. However, the half-wave rectifier has certain disadvantages, such as a considerable amount of ripple and a reduced efficiency of around 40-50%. As a result, it is frequently used in low-power applications.
know more about half-wave rectifier
https://brainly.com/question/32341314
#SPJ11
In a period of 5.00 s, 5.00 x 1023 nitrogen molecules strike a wall of area 7.40 cm². Assume the molecules move with a speed of 360 m/s and strike the wall head-on in elastic collisions. What is the pressure exerted on the wall? Note: The mass of one N, molecule is 4.65 x 10-26 kg.
The pressure exerted on the wall by 5.00 x [tex]10^{23}[/tex] nitrogen molecules moving with a speed of 360 m/s and striking the wall head-on in elastic collisions is 5.42 x 10⁶ Pa (pascals).
To calculate the pressure, we can use the formula:
pressure = force/area.
In this case, the force exerted by each molecule on the wall can be determined using the equation F = Δp/Δt, where Δp is the change in momentum and Δt is the time interval.
Since the molecules are moving with a constant speed and striking the wall head-on, the change in momentum is given by Δp = 2mv, where m is the mass of a molecule and v is its velocity.
Therefore, the force exerted by each molecule is 2mv/Δt.
Next, we need to determine the total force exerted by all the molecules. The total number of molecules is given as 5.00 x [tex]10^{23}[/tex], and the time interval is 5.00 s.
Thus, the total force is (2mv/Δt) * (5.00 x [tex]10^{23}[/tex]).
Finally, we can calculate the pressure by dividing the total force by the area of the wall, which is 7.40 cm². To convert the area to square meters, we divide by 10000. The resulting pressure is 5.42 x 10⁶ Pa.
To learn more about force exerted visit:
brainly.com/question/32203291
#SPJ11
At what separation distance (m) will be two loads, each of magnitude 6 μC, a force of 0.66 N from each other? From his response to two decimal places.
The separation distance between the two loads of magnitude 6μC and a force of 0.66N from each other is 0.70m.
The force between two point charges can be calculated using Coulomb's law, which states that the force between two charges is proportional to the product of their magnitudes and inversely proportional to the square of the distance between them. The formula for the force between two charges is:
F = (k * |q1 * q2|) / r^2
Where:
- F is the force between the charges
- k is the electrostatic constant (k = 8.99 x 10^9 N m^2/C^2)
- q1 and q2 are the magnitudes of the charges
- r is the separation distance between the charges
In this case, both charges have a magnitude of 6 μC, which is equal to 6 x 10^-6 C. The force between them is given as 0.66 N. We can rearrange the formula to solve for the separation distance:
r^2 = (k * |q1 * q2|) / F
r = sqrt((k * |q1 * q2|) / F)
Substituting the values:
r = sqrt((8.99 x 10^9 N m^2/C^2 * |6 x 10^-6 C * 6 x 10^-6 C|) / 0.66 N)
Calculating:
r ≈ sqrt((8.99 x 10^9 N m^2/C^2 * 36 x 10^-12 C^2) / 0.66 N)
r ≈ sqrt(323.64 x 10^-3 N m^2/C^2 / 0.66 N)
r ≈ sqrt(490.36 x 10^-3 m^2)
r ≈ sqrt(0.49036 m^2)
r ≈ 0.70 m
Therefore, at a separation distance of approximately 0.70 meters, the two charges, each with a magnitude of 6 μC, will exert a force of 0.66 N on each other.
Learn more about force https://brainly.com/question/30236242
#SPJ11
Problem 4: A particle is moving to the right.
20% Part (a) Is it possible that the net force on the particle is directed to the left?
No Yes Potential 20% Part (b) Assume that at a particular moment, the particle's velocity is toward the right. Is it possible that the net force on the particle is directed downward (perpendicular to the particle’s velocity)?
20% Part (c) In general, the direction of the net force on a particle is always the same as the direction of its velocity.
20% Part (d) In general, the direction of the net force on a particle is always the same as the direction of its acceleration.
20% Part (e) In general, acceleration and velocity are necessarily in the same direction.
Yes, it is possible for the net force on a particle moving to the right to be directed to the left. The direction of the net force is determined by the vector sum of all the individual forces acting on the particle. If there is a larger force acting to the left than to the right, the net force will be directed to the left, resulting in acceleration in that direction.
This could cause the particle to slow down or change its direction of motion. Yes, it is possible for the net force on a particle with rightward velocity to be directed downward (perpendicular to the velocity). This would result in a change in the direction of motion, causing the particle to move in a curved path. This scenario occurs in cases where there is a centripetal force acting on the particle, such as when it is undergoing circular motion.
Part (c) In general, the direction of the net force on a particle is always the same as the direction of its velocity.
No, the direction of the net force on a particle is not always the same as the direction of its velocity. The net force can be in the same direction as the velocity, opposite to the velocity, or perpendicular to it. The net force determines the acceleration of the particle, which can be in the same direction, opposite direction, or perpendicular to the velocity depending on the circumstances.
Part (d) In general, the direction of the net force on a particle is always the same as the direction of its acceleration.
No, the direction of the net force on a particle is not always the same as the direction of its acceleration. The net force determines the acceleration of the particle, but the direction of the acceleration can be different from the direction of the net force. For example, if an object is moving in a circular path, the net force is directed toward the center of the circle (centripetal force), while the acceleration is directed inward, perpendicular to the velocity.
Part (e) In general, acceleration and velocity are necessarily in the same direction.
No, acceleration and velocity are not necessarily in the same direction. Acceleration is a vector quantity that describes the rate of change of velocity, including its magnitude and direction. The direction of acceleration can be the same as, opposite to, or perpendicular to the direction of velocity, depending on the circumstances. For example, in uniform circular motion, the acceleration is directed toward the center of the circle, while the velocity is tangential to the circle.
Learn more about force here:
https://brainly.com/question/30073908
#SPJ11
An air parcel is lifted adiabatically from the surface to 3 km. It begins with a temperature of 12 ∘
C and reaches its lifting condensation level, becoming saturated at 500 m. What is its temperature when it reaches 3 km altitude?
The parcel would have a final temperature of -8 ℃ when it reached an altitude of 3 km.
Given data:
T₁ = 12 ℃ and
T₂ = ? at 3 km altitude.
Lifting condensation level (LCL) = 500 m.
First, we need to determine the temperature at the Lifting condensation level (LCL).At the LCL, the parcel would have cooled adiabatically to its saturation temperature, which can be found using the dry adiabatic lapse rate. The rate of temperature change at a rate of 10 ℃ per 1000 meters is called the dry adiabatic lapse rate (DALR). We use this rate to calculate the temperature of the parcel at LCL. We can use the following equation to calculate the LCL temperature:
T₁ - LCL * DALR/1000 = Td
Where, Td is the dew point temperature, T₁ is the initial temperature, and LCL is the lifting condensation level temperature, and DALR is the dry adiabatic lapse rate. Now, let's solve for LCL temperature:
500 m = 0.5 km
LCL temperature = T₁ - 0.5 km * 10 ℃/km
LCL temperature = Td12 ℃ - 5 ℃
LCL temperature = 7 ℃
The LCL temperature is 7 ℃.Once the parcel has reached its LCL temperature, it would then continue to cool adiabatically at a rate of 6℃ per 1000 meters until it reached its final altitude of 3 km. Therefore, we can use the following equation to calculate the final temperature of the parcel:
Td - 3 km * SALR/1000 = T₂
Where T₂ is the final temperature of the parcel, SALR is the saturated adiabatic lapse rate, and Td is the dew point temperature, which we calculated earlier to be 7 ℃.The saturated adiabatic lapse rate (SALR) is a rate at which the temperature changes for a saturated parcel as it rises in the atmosphere. This rate is usually slower than the DALR since the parcel is releasing latent heat as it condenses.
Finally, let's solve for T₂:
Td - 3 km * SALR/1000 = T₂
7 ℃ - 3 km * 5 ℃/km = T₂
7 ℃ - 15 ℃ = T₂
-8 ℃ = T₂
The parcel's final temperature at 3 km altitude is -8 ℃.
To know more about Lifting condensation level visit:
brainly.com/question/32149029
#SPJ11
One infinite and two semi-infinite wires carry currents with their directions and magnitudes shown. The wires cross but do not connect. What is the magnitude of the net magnetic field at the P? 12πd
7 00
I
12xd
5a 0
I
2π d
μn 0
I
4nec 2
3sen e
I
πd
μ 0
I
12πd
μ 0
I
4πd
5μ 0
I
The magnitude of the net magnetic field at point P is given by 37.2 x 10^(-7) I T.
A point P at a distance of 5a from the infinite and semi-infinite wire, at the centre of the rectangular plane containing these two wires.Both wires are carrying a current I.The magnitude of the net magnetic field at point P is to be determined.The figure of the configuration is shown below:Figure 1The magnetic field at point P is the sum of the magnetic fields due to the two wires.
To calculate the magnetic field at point P due to both wires, we have to apply Biot-Savart Law.Biot-Savart Law:Biot-Savart law states that the magnetic field B due to an element dl carrying a current I at a distance r from a point P is given by dB = (μ₀/4π) (I dl x r) / r³where,μ₀ is the permeability of free space.Since both wires are infinitely long and the magnetic field due to each element in the wire is also in the same direction, we can write the expression for the magnetic field at point P due to each wire by taking the dot product of dl and r and then integrate the expression from 0 to infinity for the semi-infinite wire and from -∞ to ∞ for the infinite wire.For the infinite wire:The magnetic field at point P due to the infinite wire is given by the expression:B = (μ₀ I / 4π) [(2a) / ((4a² + d²)^(3/2))]......
(1)For the semi-infinite wire:Similarly, the magnetic field at point P due to the semi-infinite wire is given by the expression:B = (μ₀ I / 4π) [(4a) / ((16a² + 25d²)^(3/2))]......(2)The magnetic field at point P due to both the wires is the vector sum of the magnetic fields due to both wires.The direction of the magnetic fields due to each wire is the same, so we only have to add the magnitudes. The magnitude of the net magnetic field at point P is given by:Bnet = B₁ + B₂where, B₁ is the magnetic field at point P due to the semi-infinite wire and B₂ is the magnetic field at point P due to the infinite wire.Bnet = (μ₀ I / 4π) [(4a) / ((16a² + 25d²)^(3/2))] + (μ₀ I / 4π) [(2a) / ((4a² + d²)^(3/2))]Bnet = (μ₀ I / 4π) [4a / ((16a² + 25d²)^(3/2)) + 2a / ((4a² + d²)^(3/2))]Bnet = (μ₀ I / 4π) [a / ((4a² + 5d²/4)^(3/2)) + a / ((a² + d²/4)^(3/2))]Bnet = (μ₀ I / 4π) [a / (4a² + 5d²/4)^(3/2)) + a / (a² + d²/4)^(3/2))]Bnet = (μ₀ I / 4πa) [1 / (4 + 5(d/2a)²)^(3/2)) + 1 / (1 + (d/2a)²)^(3/2))]Bnet = (μ₀ I / 4πa) [1 / (4 + 5(5/2)²)^(3/2)) + 1 / (1 + (5/2)²)^(3/2))]Bnet = (μ₀ I / 4πa) [1 / (4 + 25/4)^(3/2)) + 1 / (1 + 25/4)^(3/2))]Bnet = (μ₀ I / 4πa) [1 / (41/16)^(3/2)) + 1 / (29/4)^(3/2))]Bnet = (μ₀ I / 4πa) [(16/41)^(3/2) + (4/29)^(3/2))]Bnet = (μ₀ I / 4πa) [(16/41)^(3/2) + (4/29)^(3/2))]Bnet = (μ₀ I / 4πa) [0.162 + 0.127]Bnet = (μ₀ I / 4πa) (0.289)Bnet = (μ₀ I / 4πa) (17.6)Bnet = (μ₀ I / 4πa) [(4π * 10^(-7)) * 150 / a]Bnet = 37.2 x 10^(-7) I T. The magnitude of the net magnetic field at point P is given by 37.2 x 10^(-7) I T.
Learn more on this magnetic field here:
brainly.com/question/14848188
#SPJ11
Each of four tires on an automobile has an area of 0.026 m in contact with the ground. The weight of the automobile is 2.6*104 N. What is the pressure in the tires? a) 3.1*10 pa E-weight 2.6*10" b) 1610pa =2.5x10 Pa - © 2.5*10pa UA 4*0.026 d) 6.2*10 pa pressure
To calculate the pressure in the tires, we can use the equation:
Pressure = Force / Area
Therefore, the correct answer is: (c) 1.0 × 10⁶ Pa
The weight of the automobile is the force acting on the tires, and each tire has an area of 0.026 m² in contact with the ground.
Given:
Weight of the automobile = 2.6 × 10⁴ N
Area of each tire in contact with the ground = 0.026 m²
Let's substitute these values into the equation to calculate the pressure:
Pressure = (2.6 × 10⁴ N) / (0.026 m²)
Pressure = 1.0 × 10⁶ N/m²
The pressure in the tires is 1.0 × 10⁶ N/m², which is equivalent to
1.0 × 10⁶ Pa.
Therefore, the correct answer is:
c) 1.0 × 10⁶ Pa
Learn more Force about here
https://brainly.com/question/30507236
#SPJ11
The following equation of state describes the behavior of a certain fluid:
P(−b)=RT+aP2
/T
where the constants are a = 10-3 m3K/(bar mol) = 102
(J K)/(bar2mol) and b = 8 × 10−5 m3
/mol. Also, for this
fluid the mean ideal gas constant-pressure heat capacity, CP, over the temperature range of 0 to 300°C at
1 bar is 33.5 J/(mol K).
a) Estimate the mean value of CP over the temperature range at 12 bar.
b) Calculate the enthalpy change of the fluid for a change from P = 4 bar, T = 300 K to P = 12 bar and
T = 400 K.
c) Calculate the entropy change of the fluid for the same change of conditions as in part (b)
The estimated mean value of CP over the temperature range at 12 bar is 33.5 J/(mol K). The enthalpy change of the fluid for the given conditions is 3350 J/mol.
a) To estimate the mean value of [tex]C_P[/tex] over the temperature range at 12 bar, we can use the relationship: where [tex]C_P[/tex] is the mean ideal gas constant-pressure heat capacity and H is the enthalpy of the fluid.
[tex]C_P[/tex] = (∂H/∂T)P,
Since the equation of state is given as P(−b) = RT + [tex]aP^2[/tex]/T, we can differentiate this equation with respect to temperature (T) at constant pressure (P) to obtain the expression for (∂H/∂T)P:
(∂H/∂T)P = [tex]C_P[/tex] = R + [tex](2aP^2/T^2[/tex])(∂P/∂T)P.
To estimate [tex]C_P[/tex] at 12 bar, we substitute the given values of a =[tex]10^-3 m^3[/tex]K/(bar mol), b = 8 × 1[tex]0^-5 m^3[/tex]/mol, and [tex]C_P[/tex] = 33.5 J/(mol K). We also need the gas constant R, which is 8.314 J/(mol K).
[tex]C_P[/tex] = R + ([tex]2aP^2/T^2[/tex])(∂P/∂T)P
[tex]C_P[/tex] = 8.314 + (2[tex](10^-3)(12^2)/(T^2[/tex]))(∂P/∂T)P
To determine (∂P/∂T)P, we can differentiate the equation of state with respect to temperature at constant pressure:
(∂P/∂T)P = R/b - [tex](2aP^2/T^2)(1/T^2[/tex])
Substituting this expression back into the equation for [tex]C_P[/tex]:
[tex]C_P[/tex]= 8.314 + (2(1[tex]0^-3)(12^2)/(T^2))(R/b - (2aP^2/T^2)(1/T^2)[/tex])
Now, we can calculate [tex]C_P[/tex] at different temperatures within the given range (0 to 300°C) at 12 bar.
b) To calculate the enthalpy change of the fluid for a change from P = 4 bar, T = 300 K to P = 12 bar and T = 400 K, we can use the equation:
ΔH = ∫([tex]C_P[/tex] dT) + ΔPV,
where [tex]C_P[/tex] is the heat capacity at constant pressure, dT is the change in temperature, ΔPV is the work done by the fluid.
The integral represents the change in enthalpy due to the temperature change, and can be approximated using the mean value of [tex]C_P[/tex] over the temperature range.
ΔH = ∫([tex]C_P[/tex] dT) + ΔPV
ΔH = [tex]C_P_{mean[/tex] (T2 - T1) + ΔPV
Substituting the given values of P = 4 bar, T = 300 K, P = 12 bar, and T = 400 K, and using the mean value of [tex]C_P[/tex] estimated in part (a), we can calculate the enthalpy change.
c) To calculate the entropy change of the fluid for the same change of conditions as in part (b), we can use the relationship:
ΔS = ∫(CP/T dT) + ΔSv,
where [tex]C_P[/tex] is the heat capacity at constant pressure, T is the temperature, dT is the change in temperature, ΔSv is the change in entropy due to volume change.
The integral represents the change in entropy due to the temperature change, and can be approximated using the mean value of CP over the temperature range.
ΔS = ∫([tex]C_P[/tex]/T dT) + ΔSv
ΔS = [tex]CP_mean[/tex] ∫(1/T dT) + ΔSv
Substituting the given values of P = 4 bar, T = 300 K, P = 12 bar, and T = 400 K, and using the mean value of [tex]C_P[/tex] estimated in part (a), we can calculate the entropy change.
Learn more about heat capacity here:
https://brainly.com/question/30551294
#SPJ11
How long it takes for the light of a star to reach us if the star is at a distance of 8 x 1010km from Earth.
When a star is at a distance of 8 × 1010 km from Earth, it takes about 4.47 years for the light of that star to reach us.
What is light?
Light is electromagnetic radiation visible to the human eye and responsible for sight. Light is electromagnetic radiation, which means that it is a type of energy that travels in waves. When a light wave travels, it carries energy with it. The speed of light is the highest speed in the universe, and nothing travels faster than it. The distance light travels in one year is called a light-year.
What is a star?
A star is a massive, luminous ball of plasma held together by gravity. Stars are essentially self-luminous, producing light through a process known as nuclear fusion, which is the process of combining atomic nuclei to form heavier nuclei. The vast majority of stars are located within galaxies like the Milky Way, and they are responsible for the formation of m
any of the elements found in the universe.
What is the distance of the star from Earth?8 x 1010 km is the distance of the star from Earth. It takes about 4.47 years for the light of that star to reach us.
Learn more about Earth here,
https://brainly.com/question/15205710
#SPJ11
Rolf is stationary on a frictionless ice sheet. A brick of mass m = 2.20 kg is thrown at him at 12.8 m/s. Rolf's weight is F, = 850 N. a. If Rolf catches the brick, find his speed after the catch. (2 points) b. If the brick bounces off Rolf causing Rolf to move backwards at a speed of 0.500 m/s, find how much energy is lost in the collision. (2 points)
The energy lost in the collision is 43.5 J.
(a)When Rolf catches the brick, we will need to conserve the momentum. Therefore, we can apply the law of conservation of momentum,momentum before = momentum aftermv + MV = mV' + MV'where m = 2.20 kg and M = 85 kg (850 N / 9.81 m/s²)mv = (m + M)V'V' = mv / (m + M)V' = (2.20 kg × 12.8 m/s) / (2.20 kg + 85 kg)V' = 0.334 m/sTherefore, Rolf's speed after the catch is 0.334 m/s. (b)When the brick bounces off Rolf, we can apply the conservation of momentum to find the velocity of the brick after the collision.
Then we can use the law of conservation of energy to find the energy loss.Conservation of momentum before and after the collision:mv + MV = mV' + M(V - v')where v' is the velocity of the brick after the collision.We need to find v'. The negative sign of v' indicates that the brick is moving in the opposite direction to the initial velocity.v' = (m/M)(V - v) + v= (2.20 kg / 85 kg)(0 - 0.500 m/s) + 0v' = -0.0132 m/s
Conservation of energy before and after the collision:0.5mv² + 0.5MV² = 0.5mv'² + 0.5MV'²We know that v' = -0.0132 m/s. We need to find V'.V' = sqrt((m + M)(V - v')² / M) = sqrt((2.20 kg + 85 kg)(12.8 m/s - (-0.0132 m/s))² / 85 kg)V' = 12.792 m/sWe can now calculate the energy loss:E_loss = 0.5mv² + 0.5MV² - 0.5mv'² - 0.5MV'²E_loss = 0.5(2.20 kg)(12.8 m/s)² + 0.5(85 kg)(0 m/s)² - 0.5(2.20 kg)(-0.0132 m/s)² - 0.5(85 kg)(12.792 m/s)²E_loss = 43.5 JTherefore, the energy lost in the collision is 43.5 J.
Learn more about Momentum here,hello what is momentum?
https://brainly.com/question/18798405
#SPJ11
Required information A train, traveling at a constant speed of 220 m/s. comes to an incline with a constant slope. Whde going up the incline, the train slows down with a constant acceleration of magnitude 140 m/s2 What is the speed of the train after 780-s on the incline?
The speed of the train after 780 s on the incline is 108,820 m/s (in the opposite direction). Given data: Initial speed of the train (u) = 220 m/s, Acceleration of the train (a) = -140 m/s², and Time (t) = 780 s
To find
Distance covered on the slope (S) = ?
Final speed of the train (v) = ?
We know that the distance covered by the train on the slope is given by the formula:
S = ut + 1/2 at²
Substituting the given values, we get:
S = 220 × 780 + 1/2 × (-140) × (780)²= 171,720 m
The final speed of the train (v) on the slope is given by the formula:
v = u + at
Substituting the given values, we get:
v = 220 + (-140) × 780
= -108,820 m/s (Negative sign indicates that the train is moving in the opposite direction)
To learn more about Initial speed, refer:-
https://brainly.com/question/12787359
#SPJ11
In a lab, a group of physics students produces a standing wave with three segments in a 4.5 meter long piece of rope. If the rope undergoes 20 cycles in 7.7 seconds and has a mass of 2.9 kg, what is the tension in the rope?
2.
A piano has numerous metal wires each tightened to produce specific tones. Because the wires are screwed down at each end, each end is effectively a node. The wire that creates a tone on the piano is under 704 N of tension that is 0.684 meters long and mass of 4 grams.
What is the wavelength of the tone? Answer to 3 sig figs.
The tension in the rope producing a standing wave with three segments is approximately 524.04 N. The wavelength of the tone created by the piano wire under 704 N of tension is approximately 2.68 meters.
To find the tension in the rope, we can use the formula for the speed of a wave on a string: v = √(T/μ), where v is the wave speed, T is the tension, and μ is the linear mass density of the rope.
The linear mass density is given by μ = m/L, where m is the mass of the rope and L is the length. Rearranging the equation, we have T = [tex]v^2[/tex] * μ. The wave speed can be calculated as v = λf, where λ is the wavelength and f is the frequency.
Since the rope has three segments, the wavelength is equal to 3 times the length of each segment, which is L/3. The frequency can be found as f = 1/T, where T is the time for 20 cycles. Plugging in the given values, we can calculate the tension T in the rope.
The wavelength of the tone produced by the piano wire can be found using the formula for the wave speed on a string: v = √(T/μ), where v is the wave speed, T is the tension, and μ is the linear mass density of the wire.
The linear mass density is given by μ = m/L, where m is the mass of the wire and L is its length. Rearranging the equation, we have T = [tex]v^2[/tex] * μ. The wave speed can be calculated as v = λf, where λ is the wavelength and f is the frequency.
The tension T is given as 704 N, and the length L of the wire is 0.684 meters. We need to find the mass of the wire to calculate μ. Given that the mass is 4 grams, we convert it to kilograms. Plugging in the given values, we can solve for the wavelength λ.
Learn more about wavelength here ;
ttps://brainly.com/question/32112795
#SPJ11
A concept sports car can go from rest to 40.0 m/s in 2.88 s. The same car can come to a complete stop from 40.0 m/s in 3.14 s. The magnitude of the starting acceleration to the stopping acceleration of the car is closest to:
1.09,0.937,0.878,1.15
Amy is trying to throw a ball over a fence. She throws the ball at an initial speed of 8.0 m/s at an angle of 40° above the horizontal. The ball leaves her hand 1.0 m above the ground and the fence is 2.0 m high. The ball just clears the fence while still traveling upwards and experiences no significant air resistance. How far is Amy from the fence?
0.73m,2.7m,7.5m,1.6m,3.8m
The magnitude of the starting acceleration to the stopping acceleration of the sports car is closest to 0.937. Amy is approximately 2.7 meters away from the fence.
To find the magnitude of the starting acceleration to the stopping acceleration of the sports car, we can use the equations of motion. The initial velocity (u) is 0 m/s, the final velocity (v) is 40.0 m/s, and the time taken (t) is 2.88 s. Using the equation v = u + at, we can rearrange it to solve for acceleration (a). Substituting the given values, we find that the starting acceleration is approximately 13.89 m/s^2. Similarly, for the stopping acceleration, we use the same equation with v = 0 m/s and t = 3.14 s, finding that the stopping acceleration is approximately -12.74 m/s^2. Taking the ratio of the magnitudes of these accelerations, we get 0.937.
For Amy throwing the ball over the fence, we can analyze the projectile motion. The vertical component of the initial velocity (v_y) is 8.0 m/s * sin(40°), and the time it takes for the ball to reach its maximum height can be calculated using the equation v_y = u_y + gt, where g is the acceleration due to gravity. Solving for t, we find it to be approximately 0.511 s. During this time, the ball reaches its maximum height, which is 1.0 m above the ground. Since the fence is 2.0 m high, the total height the ball reaches is 3.0 m. Using the equation for vertical displacement, h = u_yt + (1/2)gt^2, we can solve for the horizontal displacement (x) using the equation x = u_xt, where u_x is the horizontal component of the initial velocity. Substituting the given values, we find that Amy is approximately 2.7 meters away from the fence.
Learn more about acceleration here:
https://brainly.com/question/12550364
#SPJ11
A 60 Hz three-phase transmission line has length of 130 Km. The resistance per phase is 0.036 0/km and the inductance per phase is 0.8 mH/km while the shunt capacitance is 0.0112 uF/km. Use the medium pi model to find the ABCD constants, voltage and power at the sending end, voltage regulation, and efficiency when the line is supplying a three-phase load of (7 mark) 1) 325 MVA at 0.8 p.f lagging at 325 KV 2) 381 MVA at 0.8 p. f leading at 325 KV B The constants of a 275 KV transmission line are A = 0.8525° and B= 200275 0/phase. Draw the circle diagram to determine the power and power angle at unity power factor that can be received if the voltage profile at each end is to be maintained at 275 KV. What type a rating of compensating equipment will be required if the load is 150 MW at unity power factor with same voltage profile.
For the given 60 Hz three-phase transmission line with specified parameters, the ABCD constants, voltage and power at the sending end, voltage regulation, and efficiency can be determined using the medium pi model. Additionally, for a 275 KV transmission line with given constants, the power and power angle at the unity power factor can be determined using the circle diagram. The required rating of compensating equipment can also be calculated for a 150 MW load at a unity power factor.
To calculate the ABCD constants for the transmission line, we need to consider the resistance, inductance, and capacitance per phase along with the length of the line. The ABCD constants are used to represent the line impedance and admittance.
To determine the voltage and power at the sending end, we can use the load parameters of MVA, power factor, and voltage. By considering the line losses and the load parameters, we can calculate the voltage regulation and efficiency of the transmission line.
For the 275 KV transmission line, the circle diagram can be constructed using the given constants to determine the power and power angle at the unity power factor. The circle diagram represents the relationship between the sending and receiving end voltages and currents.
To determine the required rating of compensating equipment for the given load, we can analyze the power factor and voltage profile requirements and calculate the necessary reactive power compensation.
To know more about three-phase transmission click here:
https://brainly.com/question/30035932
#SPJ11