The distributed load shown is supported by a box beam with the given dimension. a. Compute the section modulus of the beam. b. Determine the maximum load W (KN/m) that will not exceed a flexural stress of 14 MPa. c. Determine the maximum load W (KN/m) that will not exceed a shearing stress of 1.2 MPa. 300 mm W KN/m L 150 mm 1m 200 mm 2m 1m 250 mm

Answers

Answer 1

a. The section modulus of the beam is calculated to be 168.75 cm³.

The section modulus (Z) is a measure of a beam's ability to resist bending.It is determined by multiplying the moment of inertia (I) of the beam's cross-sectional shape with respect to the neutral axis by the distance (c) from the neutral axis to the extreme fiber.The moment of inertia is calculated by summing the individual moments of inertia of the rectangular sections that make up the beam.The distance (c) is half the height of the rectangular sections.

b. The maximum load (W) that will not exceed a flexural stress of 14 MPa is 21.57 kN/m

The flexural stress (σ) is calculated by dividing the bending moment (M) by the section modulus (Z) of the beam.The bending moment is determined by integrating the distributed load over the length of the beam and multiplying by the distance from the load to the point of interest.The maximum load is found by setting the flexural stress equal to the given limit and solving for the load.

c. The maximum load (W) that will not exceed a shearing stress of 1.2 MPa is 1.84 kN/m.

The shearing stress (τ) is calculated by dividing the shear force (V) by the cross-sectional area (A) of the beam.The shear force is determined by integrating the distributed load over the length of the beam.The cross-sectional area is equal to the height of the rectangular sections multiplied by the width of the beam.The maximum load is found by setting the shearing stress equal to the given limit and solving for the load.

The section modulus of the given box beam is 168.75 cm³. The maximum load that will not exceed a flexural stress of 14 MPa is 21.57 kN/m, while the maximum load that will not exceed a shearing stress of 1.2 MPa is 1.84 kN/m. These calculations are important in determining the load-bearing capacity and structural integrity of the beam under different stress conditions.

Learn more about Beam :

https://brainly.com/question/31371992

#SPJ11


Related Questions

Haley spends 90 minutes doing her homework 2/3 of an hour reason and eight minutes make you so much. How many more minutes is Haley spend with her homework and reading and making her lunch

Answers

To solve the problem, we need to first convert the given information into minutes. We know that Haley spends 90 minutes doing her homework, which is equivalent to 1 and 1/2 hours. We also know that 2/3 of an hour is equivalent to 40 minutes (since 1 hour is 60 minutes, and 2/3 of 60 is 40). Finally, eight minutes is already in minutes.

Therefore, the total time Haley spends on homework, reading, and making her lunch is:

Homework: 90 minutesReading: We don't have any information about how much time Haley spends on reading.Making lunch: 8 minutesTotal: 90 + 8 = 98 minutes

We cannot determine how many more minutes Haley spends on reading since we don't have any information about it.

Answer:

42 minutes

Step-by-step explanation:

Haley spends = 90 minutes

for reasoning = 2/3 of an hour = 2/3 * 60 = 40 minutes

further time = 8 minutes

total time consumed = 40 + 8 = 48 minutes

time left to spend with reading and making her lunch = 90 - 48

= 42 minutes

Create a rule table for a DFA that determines if a number is
odd.

Answers

If the current state is B and the input is 0, the next state remains B (odd), and if the input is 1, the next state transitions to A (even).

Here's a rule table for a DFA that determines if a number is odd:

State Input Next State

A         0                   A

A         1                   B

B         0                   B

B         1                   A

In this DFA, there are two states: A and B. State A represents an even number, while state B represents an odd number.

The input can be either 0 or 1. According to the rule table, if the current state is A and the input is 0, the next state remains A, indicating that the number is still even. If the input is 1, the next state transitions to B, indicating that the number is odd.

Similarly, if the current state is B and the input is 0, the next state remains B (odd), and if the input is 1, the next state transitions to A (even).

Learn more about odd here:

https://brainly.com/question/29377024

#SPJ11

Numer 72

69, 70, 71, and 72 Find the volume obtained by rotating the region bounded by the curves about the given axis. 69. Y sin r, y=0, x/2

Answers

To find the volume obtained by rotating the region bounded by the curves about the given axis, we need to determine the integration limits and set up an integral.

The region is bounded by the curves y = sin(x), y = 0, and x/2.

To find the limits of integration, we need to determine the x-values where the curves intersect. The curve y = sin(x) intersects the x-axis at x = 0, π, 2π, and so on. Since we are considering the interval from 0 to x/2, our limits of integration will be from 0 to π. The radius of rotation is given by r = y. In this case, r = sin(x). The volume V obtained by rotating the region can be calculated using the formula: V = π ∫[a, b] r^2 dx

Substituting the values, the integral becomes: V = π ∫[0, π] (sin(x))^2 dx

Simplifying further: V = π ∫[0, π] sin^2(x) dx

This integral can be evaluated to obtain the volume V. After integrating, the volume obtained by rotating the region bounded by the curves about the given axis will be determined.

Learn more about integral here

https://brainly.com/question/30094386

#SPJ11

(c) Provide the IUPAC formula of the following complexes. (i) Pentaamminethiocyanatochromium(III) tetrachlorozincate(II) (ii) Potassium pentachloro(phenyl)antimonate(V) (iii) mer-triamminetrichlorocobalt(III)

Answers

The IUPAC formulas of the given complexes are as follows:

(i) Pentaamminethiocyanatochromium(III) tetrachlorozincate(II)

(ii) Potassium pentachloro(phenyl)antimonate(V)

(iii) mer-triamminetrichlorocobalt(III)

(i) Pentaamminethiocyanatochromium(III) tetrachlorozincate(II): In this complex, the central metal ion is chromium in the +3 oxidation state. It is coordinated to five ammonia ligands (NH₃) and one thiocyanate ligand (SCN). The complex also contains a tetrachlorozincate(II) ion, which consists of a zinc ion (Zn²⁺) coordinated to four chloride ions (Cl⁻). Therefore, the IUPAC formula for this complex is pentaamminethiocyanatochromium(III) tetrachlorozincate(II).

(ii) Potassium pentachloro(phenyl)antimonate(V): In this complex, the central metal ion is antimony in the +5 oxidation state. It is coordinated to five chloride ligands (Cl⁻) and one phenyl ligand (C₆H₅). The complex is further associated with a potassium ion (K⁺). Hence, the IUPAC formula for this complex is potassium pentachloro(phenyl)antimonate(V).

(iii) mer-triamminetrichlorocobalt(III): In this complex, the central metal ion is cobalt in the +3 oxidation state. It is coordinated to three ammonia ligands (NH₃) and three chloride ligands (Cl⁻). The arrangement of these ligands in a meridional geometry gives the complex its name. Therefore, the IUPAC formula for this complex is mer-triamminetrichlorocobalt(III).
Learn more about IUPAC  from the given link:
https://brainly.com/question/28872356
#SPJ11

Please help me on this I will mark you brainlist :)))))))

Answers

The sequence is arithmetic, and the common difference is of 10.

What is an arithmetic sequence?

An arithmetic sequence is a sequence of values in which the difference between consecutive terms is constant and is called common difference d.

The common difference of the sequence in this problem is given as follows:

40 - 30 = 10.30 - 20 = 10.20 - 10 = 10.

As the common difference is equal, the sequence is arithmetic.

More can be learned about arithmetic sequences at https://brainly.com/question/6561461

#SPJ1

Can
you please make a problem set with these? Thank you.
• 6 problems compound, on horizontal curves (2 simple, 2 2 reversed) • 4 problems on cant/superelevation • 5 problems on vertical curves • 5 problems on sight distances

Answers

Here's an example problem set that covers compound horizontal curves, cant/superelevation, vertical curves, and sight distances:

1. Compound Horizontal Curves:
  a) Problem 1: Calculate the length of a simple horizontal curve with a radius of 200 meters and a central angle of 45 degrees.
  b) Problem 2: Determine the required superelevation for a compound horizontal curve with a radius of 150 meters and a central angle of 60 degrees.

2. Cant/Superelevation:
  a) Problem 3: Find the superelevation rate for a highway curve with a radius of 250 meters and a design speed of 80 km/h.
  b) Problem 4: Calculate the maximum allowable superelevation for a curve with a radius of 300 meters and a design speed of 60 km/h.

3. Vertical Curves:
  a) Problem 5: Determine the length of a crest vertical curve given the design speed of 70 km/h and the rate of change of grade.
  b) Problem 6: Find the minimum length of a sag vertical curve for a design speed of 90 km/h and a rate of change of grade.

4. Sight Distances:
  a) Problem 7: Calculate the stopping sight distance required for a design speed of 100 km/h and a perception-reaction time of 2.5 seconds.
  b) Problem 8: Determine the passing sight distance needed for a design speed of 80 km/h and a passing time of 10 seconds.

Learn more about crest from the given link!

https://brainly.com/question/31881914.

#SPJ11

help me pleaseeee!!!!!!!

Answers

there are six possibilities , the probability of rolling an odd no. is 3 so

[tex] \frac{3}{6} = \frac{1}{2} [/tex]

please mark me as brainliest

Which choice is equivalent to the fraction below when x is an appropriate
value? Hint: Rationalize the denominator and simplify.
4-√6z
O A.
OB. 8+2√62
16-6z
O C.
8+2√/6z
8-3
D.
2+√6z
4-6z
8-6z

Answers

The correct option is D)[tex]2+\sqrt{6z} /4-6z[/tex] .The choice is equivalent to the given fraction when x is an appropriate value is [tex]2+\sqrt{6z} /4-6z[/tex]

Let's rationalize the denominator of the given fraction as shown below:

[tex]$4 - \sqrt{6z} = \frac{(4 - \sqrt{6z}) (\overline{4 + \sqrt{6z}})}{(4 - \sqrt{6z}) (\overline{4 + \sqrt{6z}})}$[/tex]

Here, the denominator is of the form[tex]$(a-b)(a+b)$[/tex], which can be written as [tex]$a^2 - b^2$[/tex].

Therefore, the above expression can be simplified as:

[tex]\[\frac{(4 - \sqrt{6z}) (\overline{4 + \sqrt{6z}})}{(4 - \sqrt{6z}) (\overline{4 + \sqrt{6z}})} \\= \frac{(4^2 - \sqrt{(6z)^2})}{(4 - \sqrt{6z}) (\overline{4 + \sqrt{6z}})}\\\\= \frac{16 - 6z}{16 - (6z)}\\\\= \frac{16 - 6z}{10} = \frac{8-3z}{5}\][/tex]

Therefore, we can see that choice D) [tex]2+\sqrt{6z} /4-6z[/tex] is equivalent to the given fraction when x is an appropriate value.

Thus, the correct option is D) [tex]2+\sqrt{6z} /4-6z[/tex]

For more questions on fraction

https://brainly.com/question/78672

#SPJ8

Find the solution of the given initial value problem: y" + y' = sec(t), y(0) = 6, y′(0) = 3, y″(0) y(t) = = -4.

Answers

Initial value problem refers to a differential equation that has been provided with initial conditions.

We have the differential equation's"

[tex]+ y' = sec(t[/tex]

)We can find the complementary function of the given differential equation by solving the following characteristic equation:

[tex]r2 + r = 0r(r + 1) = 0r1 = 0[/tex]

and r2 = -1Hence, the complementary function is:

[tex]yC = c1 + c2 e-t[/tex]

Yap = 2At + B, i's

= 2A

From the given differential equation, we have:

y" + y' = sec(t)2A + 2At + B = sec(t

)Comparing the coefficients of both sides, we get

[tex]:A = 0, B \\= 0, \\and 2A + 2C\\ = 1\\We get\\ C = 1/2[/tex]

Therefore, the particular solution Isay = 1/2Using the initial conditions

y(0) = 6 and y′(0) = 3,

we get:

[tex]yC + yP \\= 6 + 1/2 \\= 13/2y'C + y[/tex]

'P = 0 + 0 = 0

Hence, the solution of the given initial value problem is:

y(t)

= yC + yP

= c1 + c2 e-t + 1/2.

To know more about initial visit:

https://brainly.com/question/32209767

#SPJ11

P-34 is unstable and radioactive. Is its n/p ratio too high or too low? In that case, which process could lead to stability? (Make sure that both parts of the answer are correct.) Its n/p ratio is too high. It could attain stability by electron capture. Its n/p ratio is too low. It could attain stability by beta emission. Its n/p ratio is too high. It could attain stability by alpha emission. Its n/p ratio is too low. It could attain stability by electron capture. Its n/p ratio is too high. It could attain stability by beta emission.P-34 is unstable and radioactive. Is its n/p ratio too high or too low? In that case, which process could lead to stability? (Make sure that both parts of the answer are correct.) Its n/p ratio is too high. It could attain stability by electron capture. Its n/p ratio is too low. It could attain stability by beta emission. Its n/p ratio is too high. It could attain stability by alpha emission. Its n/p ratio is too low. It could attain stability by electron capture. Its n/p ratio is too high. It could attain stability by beta emission. please tell which option and explain

Answers

So, the correct option is: Its n/p ratio is too low. It could attain stability by beta emission.

P-34 is unstable and radioactive. Its n/p ratio is too low, which means it has too few neutrons compared to protons. In this case, the process that could lead to stability is beta emission. During beta emission, a neutron in the nucleus of P-34 can undergo beta decay, where it is converted into a proton, releasing a beta particle (an electron) and an antineutrino. This conversion increases the number of protons and balances the n/p ratio, making the nucleus more stable.

To know more about beta emission,

https://brainly.com/question/32095287

#SPJ11

Problem 5.6. Consider the two-point boundary value problem -u" = 0, u(0) = 0, u'(1) = 7. 0 < x < 1; (5.6.6) Divide the interval 0≤x≤ 1 into two subintervals of length h = and let V₁ be the corresponding space of continuous piecewise linear functions vanishing at x = 0. a. Formulate a finite element method for (5.6.6). b. Calculate by hand the finite element approximation UE V₁ to (5.6.6). Study how the boundary condition at x = 1 is approximated.

Answers

The finite element method can be formulated to approximate the two-point boundary value problem -u" = 0, u(0) = 0, u'(1) = 7 on the interval 0 < x < 1 using a space of continuous piecewise linear functions vanishing at x = 0.

How can the finite element method be formulated for the given boundary value problem?

In the finite element method, we divide the interval [0, 1] into two subintervals of length h. We choose a basis function that represents a continuous piecewise linear function vanishing at x = 0.

The solution u(x) is then approximated by a linear combination of these basis functions.

By imposing the boundary conditions, we can derive a system of linear equations. Solving this system will give us the finite element approximation UE V₁ to the given boundary value problem.

The boundary condition at x = 1 can be approximated by setting the derivative of the approximation equal to the given value of 7.

This ensures that the slope of the approximate solution matches the prescribed boundary condition.

Learn more about finite element method

brainly.com/question/30003273

#SPJ11

A 13-ft wide square footing on clay soil is carrying a 349 kip load. What is the expected pressure from that load (just delta p in psf) at a depth of 18-ft (ie, not the midpoint)? B h Ap Report your answer to the nearest whole number. Do not include the units in your answer.

Answers

The expected pressure at a depth of 18 ft is 11,604 pounds per square foot.

Given that:

Load = 349 kip  

Width of the square footing = 13 ft

Depth = 18 ft

Now, the formula for the expected pressure (Δp) at a depth of 18-ft,

Δp = (Load / Area) × Depth

Now, the area of the square footing:

Area = Width × Width

= 13 ft × 13 ft

= 169 ft²

Now, we can calculate the expected pressure:

Δp = [tex]\frac{349 kip}{169 ft^2} * 18 ft[/tex]

Δp ≈ 11,604 pounds per square foot

After rounding to the nearest whole number, the expected pressure at a depth of 18 ft is , 11,604 pounds per square foot.

Learn more about the multiplication visit:

https://brainly.com/question/10873737

#SPJ4

Hydrogen (H2) in the acidic solution is produced by bonding two hydrogen atoms adsorbed on the surface of the metal electrode as follows. Here, M(s) is a metal atom on the electrode surface, and M-H(surface) is an adsorbed hydrogen atom. Make sure that the speed determination step is repeated twice (ν=2).

Answers

In an acidic solution, hydrogen gas (H2) is produced through a process called adsorption on the surface of a metal electrode. This involves the bonding of two hydrogen atoms (H) to the metal atom (M) on the electrode surface.

The process can be represented by the following equation:

M(s) + H(surface) -> M-H(surface)

Here, the metal atom M on the electrode surface bonds with an adsorbed hydrogen atom H, resulting in the formation of a metal-hydrogen complex M-H on the surface.

To determine the speed of this process, we need to consider two steps that occur twice:

1. Adsorption of hydrogen atoms on the metal surface: In this step, hydrogen atoms adsorb onto the surface of the metal electrode. This involves the interaction between the metal atom and the hydrogen atom. The adsorbed hydrogen atoms are denoted as H(surface).

2. Bonding of adsorbed hydrogen atoms to form a metal-hydrogen complex: In this step, two adsorbed hydrogen atoms (H(surface)) bond with the metal atom (M) on the surface, forming a metal-hydrogen complex (M-H(surface)).

Since these steps occur twice, the speed determination step is repeated twice (ν=2).

Overall, the process of hydrogen production in an acidic solution involves the adsorption of hydrogen atoms on the metal electrode surface, followed by their bonding to the metal atom. By repeating these steps twice, the speed of the process is determined.

To know more about hydrogen gas :

https://brainly.com/question/32820779

#SPJ11

Diane Wallace thought a living-room suite on credit, signing an installment contract with a finance compared aiat requires monthly payments of $4544 for three years, The first payment in made on the date ef signing and itaturit is 225 compounded monthly
(a) What was the cash price? (b) How much will Diane pay in total? (c) How much of what nhe pays will be interest? is the new monthly payment? a) The cath price was $1211.64 Round the tinal answer to the nearest cent as needed. Round all intermediate values to six decimal places as needed.) b) Diane will pay $163584 in total. (Round the final answer to the nearest cent as needed. Round all intermediate values to six decimal pieces as needed)
c) The amount of interest paid will be 5424:2 (Round the final answer to the nearest cent as needed. Round all intermediate values to six decimal places as needed)
d) The new monthly payment will be $ (Round the final answer to the nearest cent as needed. Round all intermediate values to sox decimal places as needed)

Answers

(a) The cash price of the living-room suite can be determined by finding the present value of the installment contract. The present value formula is given by:

PV = PMT * (1 - (1 + r)^(-n)) / r

Where PV is the present value, PMT is the monthly payment, r is the interest rate per period, and n is the number of periods.

In this case, the monthly payment (PMT) is $4544, the interest rate per period (r) is 2.25 compounded monthly, and the number of periods (n) is 36.

Using these values in the present value formula, we can calculate the cash price:

PV = $4544 * (1 - (1 + 0.0225/12)^(-36)) / (0.0225/12)

Calculating this, the cash price of the living-room suite is approximately $113,207.32.

(b) To calculate the total amount Diane will pay, we multiply the monthly payment by the number of periods:

Total amount = Monthly payment * Number of periods

Total amount = $4544 * 36

Calculating this, Diane will pay a total of $163,584.

(c) The amount of interest paid can be found by subtracting the cash price from the total amount paid:

Interest = Total amount - Cash price

Interest = $163,584 - $113,207.32

Calculating this, the amount of interest Diane will pay is approximately $50,376.68.

(d) To find the new monthly payment, we need to adjust the interest rate. Let's assume that the new interest rate is 1.75 compounded monthly.

Using the present value formula again, with the new interest rate and the cash price as the present value, we can calculate the new monthly payment:

New monthly payment = PV * (r_new / (1 - (1 + r_new)^(-n)))

New monthly payment = $113,207.32 * (0.0175/12) / (1 - (1 + 0.0175/12)^(-36))

Calculating this, the new monthly payment is approximately $3232.18.

Therefore, the answers to the given questions are:
(a) The cash price was approximately $113,207.32.
(b) Diane will pay a total of $163,584.
(c) The amount of interest Diane will pay is approximately $50,376.68.
(d) The new monthly payment will be approximately $3232.18.

Learn more about installment contract

https://brainly.com/question/30266047

#SPJ11

Consider the peptides Cys-Ser-Ala-Ile-GIn-Asn-Lys and Gln-Ser-Cys-Lys-Asn-Ile-Ala. How do these two peptides differ? a.The two peptides have different isoelectric points. b.The two peptides differ in amino acid sequence. c.The two peptides have different titration curves. d.The two peptides have different compositions.

Answers

Option b is the correct answer: The two peptides differ in amino acid sequence.

The two peptides, Cys-Ser-Ala-Ile-Gln-Asn-Lys and Gln-Ser-Cys-Lys-Asn-Ile-Ala, differ in their amino acid sequence.

Peptides are made up of amino acids linked together by peptide bonds. In this case, the two peptides have different sequences of amino acids. The first peptide starts with Cys (cysteine), followed by Ser (serine), Ala (alanine), Ile (isoleucine), Gln (glutamine), Asn (asparagine), and ends with Lys (lysine). On the other hand, the second peptide starts with Gln, followed by Ser, Cys, Lys, Asn, Ile, and ends with Ala.

Therefore, option b is the correct answer: The two peptides differ in amino acid sequence.

Learn more about Peptides amino acids:

https://brainly.com/question/14351754

#SPJ11

Find a conformal map from the sector {z=reiθ:r>0,−π/4<θ<π/4} onto the horizontal strip{z:−π

Answers

A conformal map from the sector {z=reiθ:r>0,−π/4<θ<π/4} to the horizontal strip {z:−π

How can we find a conformal map between the given sector and the horizontal strip?

To find a conformal map between the given sector and the horizontal strip, we can use the exponential function. Let's consider the transformation w = e^z, where z is in the sector and w is in the strip.

In the sector, we can represent z as z = r * e^(iθ), where r > 0 and -π/4 < θ < π/4. Now, applying the transformation, we get w = e^(r * e^(iθ)).

To simplify further, we can use Euler's formula, e^(iθ) = cosθ + i*sinθ, to rewrite the expression as w = e^(r * (cosθ + i*sinθ)).

Now, using the properties of the exponential function, we can write w = e^(r*cosθ) * e^(i*r*sinθ).

The first factor, e^(r*cosθ), represents the magnitude of w, which is positive for all r and θ. The second factor, e^(i*r*sinθ), represents the angle of w, which varies from -π/4 to π/4 as θ varies from -π/4 to π/4.

Therefore, the transformation w = e^z maps the given sector onto the horizontal strip {z:−π

Learn more about conformal map

brainly.com/question/32642636

#SPJ11

y′′+8y′+25y=0,y(0)=−2,y′(0)=20 y(t)= The behavior of the solutions are: Oscillating with decreasing amplitude Oscillating with increasing ampssitude Steady oscillation

Answers

The particular solution is y(t) = -2 * e^(-4t) * cos(3t) - (8/3) * e^(-4t) * sin(3t).

The given differential equation is y′′ + 8y′ + 25y = 0, with initial conditions y(0) = -2 and y′(0) = 20.

To determine the behavior of the solutions, we can consider the characteristic equation associated with the differential equation: r^2 + 8r + 25 = 0.

By solving this quadratic equation, we find two complex conjugate roots: r = -4 + 3i and r = -4 - 3i.

The general solution of the differential equation is then given by y(t) = c1 * e^(-4t) * cos(3t) + c2 * e^(-4t) * sin(3t), where c1 and c2 are constants determined by the initial conditions.

Using the given initial conditions, we can find the particular solution. Substituting t = 0, y(0) = -2 gives c1 = -2. Substituting t = 0, y′(0) = 20 gives c2 = -8/3.


The behavior of the solutions is oscillating with decreasing amplitude. The exponential term e^(-4t) causes the amplitude to decrease over time, while the trigonometric terms cos(3t) and sin(3t) cause the oscillation.

Learn more about particular solution from ;

https://brainly.com/question/31252913

#SPJ11

what is the hydroxide ion concentration Oh in a 0.1M solution of
HCl
a. 1 x10^-7
b. 0.0
c 1 x 10^-13
d. .10
e. 1 x10^-14

Answers

Strong acid HCl dissociates into hydrogen and chloride ions, producing a negligible hydroxide ion concentration of 1 x 10^-14 mol/L in a 0.1 M solution.So, Correct answer is E

When a strong acid such as HCl is added to water, the acid completely dissociates into its constituent ions. Since HCl is a strong acid, it dissociates completely to produce hydrogen ions and chloride ions: HCl → H+ + Cl-For a strong acid such as hydrochloric acid (HCl),

the hydroxide ion concentration is almost zero since it completely dissociates into H+ and Cl-.Since the hydroxide ion concentration in a 0.1 M HCl solution is negligible, its value is 1 x 10^-14 mol/L.

Hence, the answer to this question is option (E) 1 x10^-14.

To know more about Strong acid Visit:

https://brainly.com/question/28858976

#SPJ11

ghulam cuts out a rectangle that has a perimeter of 38 inches and a length of 15 inches. He cuts out another rectangle that is the same length and twice as wide. What is the perimeter of the new rectangle?

Answers

Answer:

The new rectangle has a perimeter of 46 inches.

Step-by-step explanation:

The perimeter of a shape is just all of the side lengths added together.

The length of the original rectangle is 15 inches. Since a rectangle has two pairs of parallel sides, this means that there are two sides with a 15 in. length.

[tex]15+15 = 30[/tex]. Find the difference between the full perimeter and these added side lengths. That is 8, which means that the other two side lengths of this rectangle both have a length of 4 in., or 8 in. together.

Now we know that the length of the rectangle is 15 in., and the width is 4 in.

We are told that the new rectangle has the same length, but is twice as wide. So, we can simply multiply the width of the original rectangle (4 in.) by 2, and that will tell us the missing side length: [tex]4*2 = 8[/tex]

So this means that the new rectangle has a length of 15 in. and a width of 8 in. For the perimeter, simply carry out [tex]15 + 15 + 8 + 8 = 46[/tex], or [tex]30 + 16 =46[/tex].

So, the new rectangle has a perimeter of 46 in.

Imagine 100 people at a party, and you tally how many wear pink or not, and if a man or not. and get these numbers: Imagine a pink-wearing guest leaves his/her wallet behind ... was it a man? What do you think?

Answers

In the given problem, it is given that there are 100 people at a party, and we have to tally how many wear pink or not, and if a man or not. Then we have to find if the pink-wearing guest who left his wallet behind was a man or not.

So, first we need to find out how many people are men and women and how many of them are wearing pink. Let's make a table for this: Pink No PinkTotalMen242348Women161741Total406189So, out of the 100 guests, there are 40 guests who are wearing pink and 60 guests who are not wearing pink. Among the 40 pink-wearing guests, 24 are men and 16 are women. The question asks whether the guest who left his wallet behind was a man or not. Since we know that there are 24 men who are wearing pink, it is more likely that the guest who left his wallet behind was a man. However, we cannot say for certain that the guest was a man as there are also 16 women wearing pink. Therefore, we can conclude that the gender of the guest who left his wallet behind cannot be determined with certainty. In this problem, we are given that there are 100 people at a party and we have to tally how many are wearing pink or not, and if a man or not. Then we have to determine whether a pink-wearing guest who left his wallet behind was a man or not. To solve this problem, we first need to find out the number of men and women at the party and how many of them are wearing pink. We can make a table to organize this information: Pink No PinkTotalMen242348Women161741Total406189From the table, we can see that out of the 100 guests, there are 40 guests who are wearing pink and 60 guests who are not wearing pink. Among the 40 pink-wearing guests, 24 are men and 16 are women. Now, we have to determine if the guest who left his wallet behind was a man or not. Since we know that there are 24 men who are wearing pink, it is more likely that the guest who left his wallet behind was a man. However, we cannot say for certain that the guest was a man as there are also 16 women wearing pink. Therefore, we can conclude that the gender of the guest who left his wallet behind cannot be determined with certainty.

From the given data, we cannot be certain whether the guest who left his wallet behind was a man or not. Although there are 24 men wearing pink, there are also 16 women wearing pink. Therefore, we can only make an educated guess that the guest was a man, but we cannot be sure.

To learn more about tally visit:

brainly.com/question/29336031

#SPJ11

Using Laplace Transforms, find the solution of the initial value problem: d²y +9y =9. sin(t). U(t - 3), = y(0) = y'(0) = 0 dx²

Answers

The solution to the given initial value problem, obtained using Laplace transforms, is y(x) = 0. This means that the function y(x) is identically zero for all values of x.

To find the solution of the initial value problem using Laplace transforms for the equation d²y/dx² + 9y = 9sin(t)u(t - 3), where y(0) = y'(0) = 0, we can follow these steps:

Take the Laplace transform of the given differential equation.

Applying the Laplace transform to the equation d²y/dx² + 9y = 9sin(t)u(t - 3), we get:

s²Y(s) - sy(0) - y'(0) + 9Y(s) = 9 * (1/s² + 1/(s² + 1))

Since y(0) = 0 and y'(0) = 0, the Laplace transform simplifies to:

s²Y(s) + 9Y(s) = 9 * (1/s² + 1/(s² + 1))

Solve for Y(s).

Combining like terms, we have:

Y(s) * (s² + 9) = 9 * (1/s² + 1/(s² + 1))

Multiply through by (s² + 1)(s² + 9) to get rid of the denominators:

Y(s) * (s⁴ + 10s² + 9) = 9 * (s² + 1)

Simplifying further, we have:

Y(s) * (s⁴ + 10s² + 9) = 9s² + 9

Divide both sides by (s⁴ + 10s² + 9) to solve for Y(s):

Y(s) = (9s² + 9)/(s⁴ + 10s² + 9)

Partial fraction decomposition.

To proceed, we need to decompose the right side of the equation using partial fraction decomposition:

Y(s) = (9s² + 9)/(s⁴ + 10s² + 9) = A/(s² + 1) + B/(s² + 9)

Multiplying through by (s⁴ + 10s² + 9), we have:

9s² + 9 = A(s² + 9) + B(s² + 1)

Equating the coefficients of like powers of s, we get:

9 = 9A + B

0 = A + B

Solving these equations, we find:

A = 0

B = 0

Therefore, the decomposition becomes:

Y(s) = 0/(s² + 1) + 0/(s² + 9)

Inverse Laplace transform.

Taking the inverse Laplace transform of the decomposed terms, we find:

L^(-1){Y(s)} = L^(-1){0/(s² + 1)} + L^(-1){0/(s² + 9)}

The inverse Laplace transform of 0/(s² + 1) is 0.

The inverse Laplace transform of 0/(s² + 9) is 0.

Combining these terms, we have:

Y(x) = 0 + 0

Therefore, the solution to the initial value problem is:

y(x) = 0

To learn more about Laplace transforms visit : https://brainly.com/question/29583725

#SPJ11

The fish population in a certain part of the ocean (in thousands of fish) as a function of the water's temperature (in degrees celsius) is modeled by: p(x)=-2x^2+40x-72

1) What type of function is being shown?

2) What other characteristics of this type of function?

3) Determine which time will result in no fish, a population of zero.

4) use a different strategy to determine which time will result in no fish.

5) Did both strategies give you the same answer? Should they?

6) Determine which temperature will result in the largest population of fish. Explain how you determine this.

Answers

3) To determine the time at which the fish population is zero:

We have the quadratic equation: -2x^2 + 40x - 72 = 0

Using the quadratic formula: x = (-b ± √(b^2 - 4ac)) / (2a)

Substituting the values from our equation: a = -2, b = 40, c = -72

x = (-40 ± √(40^2 - 4(-2)(-72))) / (2(-2))

Simplifying further:

x = (-40 ± √(1600 - 576)) / (-4)

x = (-40 ± √(1024)) / (-4)

x = (-40 ± 32) / (-4)

So, the solutions for x (temperature) that result in a population of zero are:

x1 = (-40 + 32) / (-4) = -8 / (-4) = 2

x2 = (-40 - 32) / (-4) = -72 / (-4) = 18

Therefore, the fish population will be zero at temperature x = 2°C and x = 18°C.

6) To determine the temperature that results in the largest population of fish (maximum point):

The x-coordinate of the vertex can be found using the formula: x = -b / (2a)

In our equation, a = -2 and b = 40:

x = -40 / (2(-2)) = -40 / (-4) = 10

So, the temperature x = 10°C will result in the largest population of fish. The y-coordinate of the vertex represents the maximum population.

1) The given function is a quadratic function.

2) Characteristics of a quadratic function include:

- It is a polynomial function of degree 2.

- The graph of a quadratic function is a parabola.

- It has a vertex, which is either a minimum or maximum point, depending on the coefficient of the leading term.

- The graph is symmetric about the vertical line passing through the vertex.

- The function can have either a positive or negative leading coefficient, which determines the concavity of the parabola.

3) To determine the time at which the fish population is zero, we need to find the value of x (temperature) that makes the function p(x) equal to zero:

-2x^2 + 40x - 72 = 0

To solve this quadratic equation, we can use the quadratic formula:

x = (-b ± √(b^2 - 4ac)) / (2a)

In this case, a = -2, b = 40, and c = -72. Plugging in these values into the quadratic formula, we can find the values of x that result in a population of zero.

4) An alternative strategy to determine when the fish population is zero is by factoring the quadratic equation if possible. However, the given quadratic equation doesn't appear to be easily factorable, so using the quadratic formula is a more suitable approach.

5) Both strategies should give the same answer. Whether using the quadratic formula or factoring, the solutions for x (temperature) that result in a population of zero should be identical. The quadratic formula is a general method that works for all quadratic equations, even when factoring is not immediately apparent.

6) To determine the temperature that results in the largest population of fish, we need to find the vertex of the quadratic function. The x-coordinate of the vertex can be found using the formula:

x = -b / (2a)

In this case, a = -2 and b = 40. Plugging in these values, we can calculate the temperature (x) at which the fish population is maximized. The y-coordinate of the vertex will represent the largest population of fish.

open bard bing AI

1) The function being shown is a quadratic function.

2) Characteristics of a quadratic function include having a degree of 2, a graph that forms a parabola, and an equation in the form of ax^2 + bx + c.

3) To determine when the population will be zero, we can set p(x) equal to zero and solve for x:
-2x^2 + 40x - 72 = 0

4) Another strategy to determine when the population will be zero is by factoring the quadratic equation, if possible. If factoring is not feasible, we can use the quadratic formula.

5) Both strategies should give the same answer when solving for the time resulting in a population of zero. However, the approach may differ in terms of complexity or computational ease.

6) To determine the temperature that will result in the largest population of fish, we need to find the vertex of the quadratic function. The x-coordinate of the vertex represents the temperature at which the fish population is maximized. In this case, the vertex can be found using the formula x = -b / (2a), where a, b, and c are the coefficients of the quadratic equation.

A 0.36m square prestressed concrete pile is to be driven in a clayey soil having an unconfined compressive strength of 110 kPa. Allowable capacity of the pile is 360 kN with a factor of safety of 2. Unit weight of clay is 18 kN/m3. Use =0.28. Compute for the length of the pile.

Answers

The length of the prestressed concrete pile should be approximately 18.63 meters.

To compute the length of the prestressed concrete pile, we need to consider the ultimate capacity of the pile and the bearing capacity of the clayey soil.

First, let's calculate the ultimate capacity of the pile. The allowable capacity is given as 360 kN, with a factor of safety of 2. Therefore, the ultimate capacity is 360 kN multiplied by the factor of safety, which gives us 720 kN.

Next, let's calculate the bearing capacity of the clayey soil. The unit weight of clay is given as 18 kN/m³, and the unconfined compressive strength is 110 kPa. The bearing capacity of the soil can be estimated using the Terzaghi's bearing capacity equation:

q = cNc + γDfNq + 0.5γBNγ

Where:

q = Bearing capacity of the soil

c = Cohesion of the soil (0 for clay)

Nc, Nq, and Nγ = Bearing capacity factors

γ = Unit weight of the soil

Df = Depth factor

Since the pile is square, the depth factor Df is equal to 1.0. Using the given values and bearing capacity factors for clay (Nc = 5.7, Nq = 1, Nγ = 0), we can calculate the bearing capacity:

q = 0 + 18 kN/m³ * 1 * 5.7 + 0.5 * 18 kN/m³ * 1 * 0 = 102.6 kN/m²

Finally, we can determine the length of the pile by dividing the ultimate capacity of the pile by the bearing capacity of the soil:

Length = Ultimate Capacity / Bearing Capacity

Length = 720 kN / (102.6 kN/m² * 0.36 m²)

Length = 18.63 meters

Therefore, the length of the prestressed concrete pile should be approximately 18.63 meters.

Learn more about length

https://brainly.com/question/28322552

#SPJ11

Which quadrilateral makes this statement true?

Answers

Answer:

Quadrilateral CBAD

Step-by-step explanation:

Because of symmetry, the following pairs of sides are congruent:

AB and CB

AD and CD

Answer: Quadrilateral CBAD

The BOD, of wastewater sample determine to be 35 mg/L as 20°C. The K₂ as 20°C is 0.19 day ¹. What is the BODs, if the test is run at 30°C?

Answers

The BOD (Biochemical Oxygen Demand) is a measure of the amount of oxygen required by microorganisms to break down organic matter in a wastewater sample. In this case, the BOD of the wastewater sample is determined to be 35 mg/L at 20°C. To calculate the BODs (BOD at a different temperature), we need to use the temperature coefficient factor, K₂. The K₂ value at 20°C is given as 0.19 day ¹. The temperature coefficient factor is used to adjust the BOD value based on the temperature difference. To calculate the BODs at 30°C, we can use the following formula: BODs = BOD × (K₂)^(T₂ - T₁), Where:
BOD is the initial BOD value at 20°C (35 mg/L)
K₂ is the temperature coefficient factor at 20°C (0.19 day ¹)
T₂ is the new temperature (30°C)
T₁ is the initial temperature (20°C)

Substituting the values into the formula, we have: BODs = 35 mg/L × (0.19 day ¹)^(30°C - 20°C). Calculating the exponent first: (0.19 day ¹)^(30°C - 20°C) = (0.19 day ¹)^10°C. Using the exponent rule: (0.19 day ¹)^10°C = 0.19^(10°C) day ^(¹ × 10°C) = 0.19^10 day ^10 = 0.19^10 day ^10 = 0.003847 day ^10. Substituting this value back into the formula: BODs = 35 mg/L × 0.003847 day ^10. Calculating the final value: BODs = 0.134 milligrams per liter (mg/L). Therefore, the BODs when the test is run at 30°C is approximately 0.134 mg/L.

exponent rule : https://brainly.com/question/11975096

#SPJ11

List two concerns about PFUA. b. How might the key ideas in green chemistry be used to address these concerns? 3. Polymers have benefits but these can also be environmental drawbacks. Discuss why the benefits of polymers also pose challenges to the environment. 4. Research the development of polymers by NASA Spinoff (spinoff.nasa.gov). Choose a briant pranantian make its oond choice for its

Answers

Two major concerns associated with the use of PFUA are: i) PFUA is persistent in the environment and bioaccumulates, ii) PFUA is also toxic and can cause a variety of health problems.

Green chemistry can be used to address concerns about PFUA by developing safer alternatives to the chemical, reducing the amount of PFUA used and the amount released into the environment, and finding ways to safely dispose of PFUA when it is no longer needed. One key idea of green chemistry is to design chemicals that are safer for humans and the environment, which could help to reduce the use of PFUA. Another key idea is to use renewable resources and to minimize waste, which could help to reduce the amount of PFUA that is released into the environment.

Polymers have benefits but these can also be environmental drawbacks. Discuss why the benefits of polymers also pose challenges to the environment. Polymers are materials that are widely used in manufacturing because of their many benefits. These benefits include their strength, durability, flexibility, and low cost. However, these benefits also pose challenges to the environment. For example, because polymers are so durable, they can persist in the environment for a long time after they are discarded, which can lead to pollution and other environmental problems. Additionally, the production of polymers can require large amounts of energy and resources, which can contribute to climate change and other environmental problems.

Research the development of polymers by NASA Spinoff (spinoff.nasa.gov). Choose a brilliant plant and make its best choice for its development. NASA Spinoff is a program that promotes the development of technology and materials that have been developed for space exploration for use in other applications. One plant that could benefit from the development of polymers by NASA Spinoff is cotton. Cotton is a valuable crop that is used to produce a variety of materials, including clothing and other textiles. However, cotton production can be very resource-intensive and can have negative environmental impacts. By developing polymers that can be used to produce textiles and other materials, NASA Spinoff could help to reduce the environmental impacts of cotton production. The best choice for the development of polymers for use in cotton production would be to focus on the use of renewable resources and to minimize waste. This could help to reduce the amount of resources needed to produce cotton and could help to reduce the environmental impacts of cotton production.

PFUA is a chemical that has many concerns associated with it, including its persistence in the environment and toxicity. The key ideas of green chemistry can be used to address these concerns by developing safer alternatives to PFUA and finding ways to reduce its use and environmental impact. Polymers have many benefits, but they also pose challenges to the environment. By developing polymers for use in cotton production, NASA Spinoff could help to reduce the environmental impacts of cotton production. The best choice for this development would be to focus on renewable resources and waste reduction.

Learn more about Polymers visit:

brainly.com/question/1443134

#SPJ11

Question 8 3 Points Krista deposits P20,000 in a bank account at 3.8% compounded quarterly for 5 years. If the inflation rate of 5.8% per year continues for this period, calculate the purchasing power of the original principal. Round your answer to 2 decimal places. Add your answer

Answers

the purchasing power of the original principal amount after 5 years, considering the effects of compound interest and inflation, is approximately P18,223.71.

To calculate the purchasing power of the original principal after 5 years, we need to consider the effects of compound interest and inflation on the deposited amount.

Given:

Principal amount (P) = P20,000

Interest rate (r) = 3.8% (compounded quarterly)

Time period (t) = 5 years

Inflation rate = 5.8% per year

First, let's calculate the future value of the principal amount after 5 years using compound interest:

Future Value =[tex]P * (1 + r/n)^{(n*t)}[/tex]

Where:

P = Principal amount

r = Interest rate

n = Number of compounding periods per year

t = Time period

Since the interest is compounded quarterly (4 times per year), we have:

n = 4

Future Value =[tex]P * (1 + r/n)^{(n*t)}[/tex]

Future Value = [tex]20000 * (1 + 0.038/4)^{(4*5)}[/tex]

[tex]Future Value = 20000 * (1 + 0.0095)^{20}[/tex]

Future Value ≈ 20000 * 1.201163

Future Value ≈ 24023.26

So, after 5 years of compounding interest at a rate of 3.8% compounded quarterly, the principal amount of P20,000 will grow to approximately P24,023.26.

Now, let's calculate the purchasing power of the original principal by accounting for the inflation rate:

Purchasing Power = Future Value / (1 + inflation rate)^time period

Purchasing Power = 24023.26 / (1 + 0.058)^5

Purchasing Power ≈ 24023.26 / 1.319506

Purchasing Power ≈ 18223.71

To know more about Number visit:

brainly.com/question/3589540

#SPJ11

Express 250 as its product of prime factors. write the prime numbers in ascending order

Answers

Answer:

2 5 5 5

Divide 250 by least prime number

2 250

1 150

5 25

5 5

1

Find the absolute maximum and minimum, if either exists, for: 1. f(x)=x²-12x+6 12. f(x) = 9x³-1 3. f(x)=8x4-3

Answers

For the given functions, the absolute maximum and minimum values depend on the domain of the functions. Without specifying the domain, it is not possible to determine the absolute maximum and minimum.

To find the absolute maximum and minimum values, we need to consider the domain of the functions. Without a specified domain, we can analyze the behavior of the functions in the entire real number line.

1. f(x) = x² - 12x + 6: This is a quadratic function. Since the leading coefficient is positive, the parabola opens upward. Without a specified domain, the function does not have an absolute maximum or minimum, but it has a vertex at the point (6, -18).

2. f(x) = 9x³ - 1: This is a cubic function. Without a specified domain, the function does not have an absolute maximum or minimum, but it extends infinitely in both directions.

3. f(x) = 8x⁴ - 3: This is a quartic function. Since the leading coefficient is positive, the function will open upward. Without a specified domain, the function does not have an absolute maximum or minimum, but it extends infinitely in both directions.

To determine the absolute maximum and minimum values, the domain of each function needs to be specified.

Learn more about quadratic function here: brainly.com/question/18958913

#SPJ11

In the diagram, BCD is a straight line. Angle ACB is a right angle. BC=6cm, tan x= 1.3 and cos y = 0.4 Work out the length of AD.

Answers

Answer:

Step-by-step explanation:

12

Other Questions
The Bill of Rights in Chapter II of the Constitution, bestows on every South African anumber of fundamental rights, one of which is the right to equality.Everybody is equal before the law and nobody may unfairly discriminate againstanother. Design an Anti-discrimination policy for a company of your choice.Your policy should ensure that it meets the requirements of a policy document followingthe correct format. (25)MARKS Use the shell method to find the volume of the solid generated by revolving the regions bounded by the curves and lines about the x-axis y=x, y=0, y=x-2 The volume is (Type an exact answer, using as needed.) 7. The transfer function of transportation lag is OG(s) = exp(-Ts) O G(s) = exp(Ts) O G(s) = exp(T/s) OG(s) = exp(s/T) 1 point TRUE / FALSE. """Client snorts $50-worth of cocaine a day"" is an example of atreatment plan's Statement ofProblem. In the following scenarios, try to imagine the brain of a person with the described head injury. What do you think is going wrong in each case? What are some alternatives?A man comes in after falling from a ladder. He is having trouble with his vision and balance, and seems to have difficulty keeping his emotions in check. What structures of his brain might be affected and why? Where do you think his injury was? Consider different possibilities and try to discuss various alternatives.(For this one pay close attention to the section 2.4 on the hemispheres and language dominance.) A woman has had a stroke and is having trouble with language. She understands what people say to her but can no longer read, even though her vision is perfect. She also has real difficulty speaking she speaks in kind of a telegraphic style, so that when she thinks its hot and we should turn on the air conditioner she says, "hot turn", trying to speak normally but leaving out most of the sentence, clearly frustrated. What structures do you think were affected by her stroke? Again, try to consider the whole system and various possibilities.You probably realize how hard your brain works 24/7, often in ways beyond your awareness.3. Choose an important activity (for example, giving a presentation in class, helping someone in distress, going on a first date) and discuss how specific structures of the A) limbic system, B) brainstem, and C) cerebellum may be involved. The current population of Tanzania is 50.3 million with a population growth rate of 2.14% per year. The average annual agricultural yield in Tanzania is 8,670 kg/ha (where "ha" means hectare, which you can think of as a metric acre), a yield that is comprised of both grains (e.g. maize/corn) and tubers of about 1.5% per year for the last five years or so. Ideally, one person should have a caloric intake of at least 2000kcal per day in order to maintain their 1 kg grain supplies 3000 kcal; 1 kg tubers supplies 1000 kcal. Use the equations from our mini-lecture and the linear growth equation from the last module quantitative assignment, to answer the following questions. You will also have to do some conversions for which you won't find specific equations. answer to one place past the decimal and put your answer in "millions", so that if your answer is 55,670,000 your answer is 55.7 Million and yould enter 55.7 as your answer. Answer: 56.6 Consider the function f(x) = xe. For this function there are three important open intervals: (-[infinity]o, A), (A, B), and (B, oo) where A and B are the critical numbers. Find A and B For each of the following intervals, tell whether f(x) is increasing or decreasing. (-[infinity]o, A): Select an answer (A, B): Select an answer (B, [infinity]o) Derive the expression for temperature distributionduring steady state heat conduction ina solid sphere. Please solve step by step. Consider a system of N particles, located in a Cartesian coordinate system, (x,y,z), show that in this case the Lagrange equations of motion become Newton's equations of motion. Hint: 2 2 2 dzi _dx dyi mildt =N 1/2" T = + + dt dt i=1 Your chapter presents an extensive discussion around the natureof prejudice. Take any concept presented concerning prejudice or inresearch related to it and discuss your perspective on thetopic. You are curious whether studerks perform better on riddles in a room with a view (i.e., with windows) than one without. So, you randomly assign participants to either the room with a view or to the one without (both right next to each other, on a busy street). Which of the following is least likely to be a confounding variable? temperature the amount of light present participants' interest in riddles noise level O A value of ko = 30 h has been determined for a fermenter at its maximum practical agitator rotational speed and with air being sparged at 0.51 gas / 1 reactor volume-min. E. coll, with a specific rate of oxygen consumption Qo, + 10 mmol/gcelih are to be cultured. The dissolved oxygen concentration in the fermentation broth is 0.2 mg/. The solubility of oxygen from air is 7.3 mg/l at 35 *C Which concentration of E. coll can be expected in the fermenter at 35 C under these oxygen-transfer limitations? A: 0.67 g cell/ Read the excerpt from T.S. Eliots "Preludes." Which form of poetry is used?The winter evening settles downWith smell of steaks in passageways.Six oclock.The burnt-out ends of smoky days.And now a gusty shower wrapsThe grimy scrapsOf withered leaves about your feetAnd newspapers from vacant lots;The showers beatOn broken blinds and chimney-pots,And at the corner of the streetA lonely cab-horse steams and stamps.And then the lighting of the lamps. A. fixed form B. closed form C. free verse D. blank verse QUESTION 1 Given the data set (27, 34, 15, 20, 25, 30, 28, 25). Find the 71st percentile. QUESTION 2 For the following Lp values, find k a. Lp = 8.41 ok= od= b. Lp = 2.4 ok= od= c. Lp = 3.77 o k= od= 100 We can use macroeconomic analysis to Select one: a. study the choices made by households. b. understand marginal changes in the macroeconomy. c. learn how to balance a checkbook. d. understand why economies grow. Consider a linear flow system given and the given data width=350', h=20 L=1200 ft k = 130 md $= 15%, }=2 cp When a slightly compressible multi-phase liquid, calculate the flow rate at both ends of the linear system. The liquid has an average compressibility of 16 x 105 psi . Throughout the novel, Santiago's recurring thoughts of returning to life as a shepherd representQuestion 21 options:the human tendency to seek the familiar when we are afraid.the pitfalls we encounter in pursuit of our goals.Santiago's ability to pursue multiple paths simultaneously.how our subconscious desires become known to us when the time is right. please help quick Which of the following are solutions to the quadratic equation? Check all thatapply. Calculate the fluid intake of an infant weighing 2 Kg:D10W at 10 cc/hr __________ cc/kg/dayD10W at 12 cc/hr___________cc/kg/dayD10W at 6.7 cc/hr___________cc/kg/dayCalculate the fluid and caloric intake of an infant weighing 1700 grams PIV order: HAL D10W at 6 cc/hr, Lipid 10% at 1 cc/hr, and feeding of PE 22 22 at 6 CC Q3 hrs:___________ cc/kg/day___________cal/kg/dayInfant birth weight 300 grams, new admission, order PIV D10W 80 cc/kg/day at what rate will the PIV rate be set? _______ cc/hrThen this ^same infant starts PO Enfamil 20 at 5 cc Q3, increasing feedings 5 cc every other feeding and titrate PIV to keep total fluid intake of 80 cc/kg/day:What rate will the PIV rate be set at after the infant took 5 cc of Enfamil? ______ cc/hrWhat will the PIV rate be set at after the infant took 15 cc of Enfamil?______ cc/hrWhat will the PIV rate be set at if the infant took 20 cc and has emesis of 5 cc? ______cc/hrWhat will be his full feed? _____ cc Q3 hr, ______cc Q4 hr If f(x) = 16x2, what is the value of f(2.5)?