1. The process involves reforming methane with steam to produce synthesis gas. 2. Mass balances are solved to determine the reactant and product flow rates. 3. The CH4 conversion is calculated based on the reactant and product flow rates. 4. The heat gained by the mixture of methane and steam in the heat exchanger is determined.5. The amount of superheated vapor fed to the heat exchanger is calculated.6. The heat of reaction for the reforming reaction is determined. 7. The heat lost/gained by the reactor is calculated.
1. The diagram of the process involves a heat exchanger and a reactor. Methane and steam enter the heat exchanger, where they are heated with superheated vapor. The mixture then enters the reactor, and the products (synthesis gas) exit the reactor.
2. Mass balances are solved based on the given information. It is stated that 250 mol/s of methane with 100% excess steam are fed to the heat exchanger. Therefore, the flow rate of methane is 250 mol/s and the flow rate of steam is also 250 mol/s. The desired product is 600 mol/s of hydrogen (H2), so the flow rate of CO and H2 can be determined as well.
3. The CH4 conversion is calculated by comparing the initial moles of methane with the moles of methane that have reacted. In this case, all 250 mol/s of methane react, resulting in a 100% conversion.
4. The heat gained by the mixture of methane and steam in the heat exchanger can be determined using the equation Q = m * Cp * ΔT, where Q is the heat gained, m is the mass flow rate, Cp is the specific heat capacity, and ΔT is the temperature change. The specific heat capacity can be estimated based on the properties of methane and steam.
5. The amount of superheated vapor fed to the heat exchanger can be determined based on the energy balance. The energy gained by the mixture of methane and steam in the heat exchanger is equal to the energy supplied by the superheated vapor.
6. The heat of reaction for the reforming reaction at 25 °C can be determined using thermodynamic data and enthalpy calculations.
7. The heat lost/gained by the reactor can be calculated by considering the energy balance. The heat lost by the reactants entering the reactor is equal to the heat gained by the products leaving the reactor, taking into account any heat of reaction and the temperature change.
Learn more about methane : brainly.com/question/12645626
#SPJ11
How would the pressure drop and pressure-drop parameters (α and
βo ), change if the particle diameter were reduced by 25%.
(Turbulent flow dominant). α1 = 7,48g-1 ; βo1 = 25760 Pa/m.
The actual pressure drop and parameters may vary depending on the specific conditions and characteristics of the system. they are based on the assumptions the Ergun equation.
If the particle diameter is reduced by 25% in a system where turbulent flow is dominant, the pressure drop and pressure-drop parameters (α and βo) would change as follows:
Pressure Drop (ΔP):
The pressure drop in a packed bed can be calculated using the Ergun equation. In this case, since the flow is turbulent, the simplified form of the Ergun equation is applicable.
The pressure drop can be expressed as:
ΔP = α (1 - ε)^2 L ρu^2 / (2 ε^3 Dp) + βo (1 - ε) L ρu^2 / ε^3
If we assume that all other parameters remain constant, except for the particle diameter, the new pressure drop ΔP2 can be calculated as:
ΔP2 = α2 (1 - ε)^2 L ρu^2 / (2 ε^3 Dp2) + βo2 (1 - ε) L ρu^2 / ε^3
Pressure-Drop Parameter (α):
The pressure-drop parameter α is a measure of the resistance to flow in the packed bed. It is defined as the ratio of pressure drop per unit bed weight.
The new value of α, denoted as α2, can be calculated as:
α2 = α1 / Dp2
Interstitial Velocity Parameter (βo):
The interstitial velocity parameter βo is a measure of the resistance to flow due to the presence of the void spaces between particles.
The new value of βo, denoted as βo2, can be calculated as:
βo2 = βo1 / Dp2
In this specific case, the given values are:
α1 = 7.48 g^-1 (or 7480 kg^-1)
βo1 = 25760 Pa/m
To determine the new values, we need to calculate the reduced particle diameter (Dp2) by reducing it by 25%:
Dp2 = Dp1 - 0.25 * Dp1
= 0.75 * Dp1
Then, we can calculate the new values of α2 and βo2 as follows:
α2 = α1 / Dp2
βo2 = βo1 / Dp2
Please note that these calculations are approximate, as they are based on the assumptions made and the simplified form of the Ergun equation. The actual pressure drop and parameters may vary depending on the specific conditions and characteristics of the system.
To know more about Ergun equation, visit:
https://brainly.com/question/31427524
#SPJ11
Summarize the basic properties and structure of polymers, explain the synthesis method, and give examples used in daily life.
Polymers are large molecules composed of repeating subunits called monomers.
They possess several unique properties: High molecular weight: Polymers have a high molecular weight, which contributes to their physical and mechanical properties. Chain-like structure: Polymers consist of long chains or networks of interconnected monomers. Diversity: Polymers exhibit a wide range of properties depending on the monomers used and their arrangement. Versatility: Polymers can be engineered to have specific properties, making them suitable for various applications. Thermal stability: Many polymers have high melting points and can withstand elevated temperatures. The synthesis of polymers involves polymerization, which can occur through various methods: Addition Polymerization: Monomers with unsaturated bonds react to form a chain, such as in the synthesis of polyethylene. Condensation Polymerization: Monomers react, eliminating small molecules like water or alcohol, as seen in the formation of polyesters.
Ring-Opening Polymerization: Monomers with cyclic structures open and link together, as in the synthesis of polycaprolactam (nylon-6).Crosslinking: Monomers form covalent bonds between chains, resulting in a three-dimensional network, as in the production of rubber. Polymers are extensively used in daily life, including: Polyethylene: Used in packaging materials like plastic bags and bottles. Polypropylene: Found in various household items, such as containers and furniture. Polyvinyl chloride (PVC): Used in pipes, cables, and flooring. Polyethylene terephthalate (PET): Commonly used for beverage bottles. Polystyrene: Found in disposable utensils, insulation, and packaging materials. These examples illustrate the wide range of applications and the importance of polymers in our daily lives.
To learn more about Polymers click here: brainly.com/question/1443134
#SPJ11
Question 3 A mixer is used to heat water. Liquid water enters the mixer at 60 °C and 15 MPa with a flowrate of 20 kg/s. Vapour enters at 15 MPa and 400 °C. The outlet is a saturated liquid at 14 MPa. a) What is the outlet flowrate (in kg/s)? b) What is the rate of entropy generation (in kJ/K.s) from this process? If you could not answer part (a), assume the outlet flowrate is 45 kg/s.
a) The outlet flowrate is 20 kg/s.
b) The rate of entropy generation from the process is approximately 254.68 kJ/(K·s).
a) Outlet flowrate calculation:
Since the inlet flowrate is given as 20 kg/s, we can assume the outlet flowrate is also 20 kg/s, as specified in the problem statement. Therefore, the outlet flowrate is 20 kg/s.
b) Rate of entropy generation calculation:
The rate of entropy generation can be determined using the energy balance equation and the given information. The energy balance equation for a control volume can be written as:
∑(m_dot * h_in) - ∑(m_dot * h_out) = Q - W
Where:
m_dot: Mass flow rate
h: Specific enthalpy
Q: Heat transfer
W: Work transfer
In this case, we can assume that there is no heat transfer (Q = 0) and no work transfer (W = 0) because the problem statement does not provide any information about those values.
The entropy generation rate can be calculated using the following equation:
Rate of entropy generation = ∑(m_dot * s_out) - ∑(m_dot * s_in)
Where:
s: Specific entropy
Let's calculate the specific enthalpies and specific entropies at each state:
For the inlet water:
State 1: T1 = 60 °C = 333.15 K, P1 = 15 MPa
Using the water properties table, we can find:
h1 = 3159.4 kJ/kg
s1 = 6.651 kJ/(kg·K)
For the inlet vapor:
State 2: T2 = 400 °C = 673.15 K, P2 = 15 MPa
Using the water properties table, we can find:
h2 = 3477.7 kJ/kg
s2 = 7.403 kJ/(kg·K)
For the outlet liquid:
State 3: P3 = 14 MPa (saturated liquid)
Using the water properties table, we can find:
h3 = 323.2 kJ/kg
s3 = 1.172 kJ/(kg·K)
Now we can calculate the rate of entropy generation:
Rate of entropy generation = (m_dot1 * s1 + m_dot2 * s2) - m_dot3 * s3
Substituting the values:
Rate of entropy generation = (20 kg/s * 6.651 kJ/(kg·K) + 20 kg/s * 7.403 kJ/(kg·K)) - 20 kg/s * 1.172 kJ/(kg·K)
Rate of entropy generation ≈ 254.68 kJ/(K·s)
Therefore, the rate of entropy generation from this process is approximately 254.68 kJ/(K·s).
Learn more about Rate of entropy here: brainly.com/question/31966522
#SPJ11
Alla™ 1.2. Give the IUPAC names of each of the following di-substituted benzene compounds and also assign the substituents as either (Para (p), Ortho(o) or Meta(m)). (5) NO₂ 1.2.1 Br SO3H 1.2.2 OH
1.2.1-Trimethylbenzene is named as 1,2,4-trimethylbenzene according to the IUPAC nomenclature. Bromotoluene is named as 1-bromo-2-methylbenzene. Benzenesulfonic acid is named as 1-sulfobenzoic acid. Phenol is named as 2-hydroxy-1-methylbenzene.
Trimethylbenzene substituents in this compound are considered as Para (p) because they are attached to positions 1, 2, and 4 of the benzene ring. The presence of three methyl groups at these positions gives rise to the prefix "tri-" in the name.
1.2.1-Bromotoluene is named as 1-bromo-2-methylbenzene. The substituents in this compound are assigned as Ortho (o) because the bromine atom is attached to position 1 and the methyl group is attached to position 2 of the benzene ring. The substituents are in adjacent positions, hence the prefix "ortho-".
1.2.1-Benzenesulfonic acid is named as 1-sulfobenzoic acid. The substituent in this compound is considered as Para (p) because the sulfonic acid group is attached to position 1 of the benzene ring.
1.2.2-Phenol is named as 2-hydroxy-1-methylbenzene. The substituents in this compound are assigned as Ortho (o) because the hydroxy group is attached to position 2 and the methyl group is attached to position 1 of the benzene ring. The substituents are in adjacent positions, hence the prefix "ortho-".
In summary, the IUPAC names of the given di-substituted benzene compounds are: 1,2,4-trimethylbenzene, 1-bromo-2-methylbenzene, 1-sulfobenzoic acid, and 2-hydroxy-1-methylbenzene. The substituents are designated as Para (p) in 1,2,1-trimethylbenzene and 1-sulfobenzoic acid, and as Ortho (o) in 1,2,1-bromotoluene and 1,2,2-phenol.
To know more about Trimethylbenzene , visit;
https://brainly.com/question/28772551
#SPJ11
b) The specific gravity of acetone is 0.791 at 20 °C. Calculate the density of acetone in lb/ft³
The density of acetone at 20 °C can be calculated using its specific gravity of 0.791. The density of acetone is approximately 49.5 lb/ft³.
The specific gravity of a substance is the ratio of its density to the density of a reference substance, usually water. In this case, the specific gravity of acetone is given as 0.791 at 20 °C. To calculate the density of acetone in lb/ft³, we need to know the density of water at the same temperature. At 20 °C, the density of water is approximately 62.43 lb/ft³.
The formula to calculate the density of a substance using specific gravity is:
Density of substance = Specific gravity × Density of reference substance
Plugging in the values, we have:
Density of acetone = 0.791 × 62.43 lb/ft³
Calculating this, we find that the density of acetone is approximately 49.5 lb/ft³. Therefore, at 20 °C, the density of acetone is approximately 49.5 lb/ft³.
Learn more about density : brainly.com/question/29775886
#SPJ11
While 200 kW of power is input to a cooling machine operating in
accordance with the reversible Carnot cycle, 2000 kW of waste heat
is released into the heat well at 27°C. What is the cooling effect
Cooling effect is 120 kW.
Given information: Power input to cooling machine = 200 kW
Heat released to heat well at 27°C = 2000 kW
We are supposed to calculate the cooling effect. Using the reversible Carnot cycle, the formula for the efficiency of a refrigerator is given by the expression:
e = T2 / (T2 - T1)where,
e is the efficiency of the refrigerator
T2 is the temperature of the heat sink
T1 is the temperature of the heat source
We can calculate the temperature of the hot reservoir as follows:
Q2 = Q1 + WcQ2 = heat rejected to the cold reservoir = 2000 kW
Q1 = heat absorbed from the hot reservoir = 200 kW (given)
Wc = work done by the refrigerator (negative of the power input) = -200 kW2000 kW = 200 kW + Wc
Wc = 2000 - 200 = 1800 kW
Using the formula of the Carnot cycle efficiency, we have:
e = T2 / (T2 - T1)T2 / T1 = e / (1 - e)T2 / 300 = 0.6 / (1 - 0.6)
T2 = 720 K
The temperature of the heat sink T2 is 720 K = 447°C.
The cooling effect is calculated as follows:
Qc = Q1(e)
Qc = 200(0.6) = 120 kW
Know more about effect here:
https://brainly.com/question/14495142
#SPJ11
Zn (s) | Zn²+ (aq) || Cr³+ (aq) | Cr(s) o Assignment: Given the following notation for a voltaic cell Draw a diagram of the cell illustrating the anode, cathode, salt bridge, electrodes with their respective ions in solution and include a meter of voltage (voltmeter) Write the oxidation and reduction reactions. Determine the electrons transferred. write the net reaction Determine the emf (voltage) of the cell Calculate the net wo
Anode: Zn (s)
Cathode: Cr³+ (aq)
Salt bridge: ||
Oxidation reaction: Zn (s) -> Zn²+ (aq) + 2e-
Reduction reaction: Cr³+ (aq) + 3e- -> Cr (s)
Electrons transferred: 2 electrons in the oxidation reaction and 3 electrons in the reduction reaction.
Net reaction: Zn (s) + Cr³+ (aq) -> Zn²+ (aq) + Cr (s)
EMF (Voltage) of the cell: 0.02 V
Net work: -3.86 kJ (negative value indicates work is done on the system)
Diagram of the Voltaic Cell: Zn (s) | Zn²+ (aq) || Cr³+ (aq) | Cr (s)
Anode: Zn (s)
Cathode: Cr³+ (aq)
Salt bridge: ||
| Salt Bridge |
Zn²+ (aq) || Cr³+ (aq)
_______________
| |
| Voltmeter |
|_______________|
Oxidation reaction (at the anode):
Zn (s) -> Zn²+ (aq) + 2e-
Reduction reaction (at the cathode):
Cr³+ (aq) + 3e- -> Cr (s)
Electrons transferred:
2 electrons are transferred in the oxidation reaction (Zn -> Zn²+)
3 electrons are transferred in the reduction reaction (Cr³+ + 3e- -> Cr)
Net reaction:
Zn (s) + Cr³+ (aq) -> Zn²+ (aq) + Cr (s)
EMF (Voltage) of the cell:
The EMF of the cell can be determined using the standard reduction potentials of Zn²+ and Cr³+ ions. The standard reduction potential for Zn²+ is -0.76 V, and for Cr³+ is -0.74 V. The EMF of the cell is the difference between the reduction potentials:
EMF = E°(cathode) - E°(anode)
EMF = -0.74 V - (-0.76 V)
EMF = 0.02 V
The net work done by the cell can be calculated using the equation:
Work = -nFEMF
where n is the number of moles of electrons transferred, F is the Faraday constant (96485 C/mol), and EMF is the electromotive force of the cell.
Work = -(2 mol + 3 mol) * 96485 C/mol * 0.02 V
Work = -3859.4 J (or -3.86 kJ)
Learn more about Cathode at https://brainly.com/question/2349926
#SPJ11
How
does secondary steelmaking affect the final properties of strip
steel?
Secondary steelmaking plays a crucial role in the production of strip steel as it significantly influences the final properties of the steel. By employing various refining techniques, secondary steelmaking helps to adjust and enhance the composition and cleanliness of the steel.
Resulting in improved mechanical, chemical, and surface properties. The boundary layer thickness is not directly related to secondary steelmaking and thus is not applicable to this context. Secondary steelmaking refers to the refining process that follows primary steelmaking (e.g., basic oxygen furnace or electric arc furnace) and precedes the casting or rolling of the steel. It involves various operations such as ladle refining, degassing, desulfurization, alloying, and temperature adjustment.
During secondary steelmaking, the composition of the steel can be adjusted to achieve the desired chemical properties. Impurities, such as sulfur and phosphorus, can be reduced, and alloying elements can be added to enhance specific characteristics of the steel. This allows for greater control over the steel's mechanical properties, such as strength, hardness, and toughness.
Secondary steelmaking also plays a crucial role in improving the cleanliness of the steel. By employing processes like ladle metallurgy refining and vacuum degassing, non-metallic inclusions, such as oxides and sulfides, can be reduced or eliminated. Cleaner steel with lower inclusion content has improved surface quality, reduced defects, and enhanced corrosion resistance. The final properties of strip steel, including mechanical strength, ductility, formability, surface quality, and chemical composition, are significantly influenced by the secondary steelmaking processes. The adjustments made during secondary steelmaking ensure that the steel meets the required specifications and standards for its intended applications.
Regarding the boundary layer thickness, it is a concept related to fluid dynamics and is not directly applicable to the steelmaking process. The boundary layer thickness refers to the region near a solid surface where the velocity of the fluid changes due to viscous effects. It is a topic studied in fluid mechanics and typically applies to fluid flow over surfaces, such as in aerodynamics or heat transfer. It does not have a direct impact on the properties of strip steel during the secondary steelmaking process.
Learn more about viscous effects here:- brainly.com/question/889499
#SPJ11
Which sentence in the section "Measuring Sonic Booms" BEST supports the conclusion that sonic booms are not dangerous?
A. Air molecules are pressing down on us all the time.
B. However, we do not feel them because our bodies are used to the pressure.
C. Sonic booms pack air molecules tightly together, so this means the air pressure is greater.
D. Most structures in good condition can withstand sonic booms.
Next
Answer:
B. However, we do not feel them because our bodies are used to the pressure.
22. Briefly explain the main characteristic of the inhibitory water-based mud. 23. Which substance is used to control the Ca2+ solubility in the lime mud? 24. What should be the salt concentration to use the inhibitory mud as salt mud?
Its ability is to suppress the swelling and dispersion of clay minerals. CaCO3 is used to control the solubility . The salt concentration varies based on specific drilling conditions and desired inhibitory effects.
Inhibitory water-based mud is formulated to counteract the reactive nature of clay minerals encountered during drilling. The main characteristic of inhibitory mud is its ability to reduce the swelling and dispersion of clay minerals, thereby preventing the wellbore instability issues caused by clay hydration. Inhibitory additives such as shale inhibitors, thinners, and stabilizers are incorporated into the mud to achieve this suppression effect.
To control the solubility of Ca2+ in lime mud, a substance like calcium carbonate (CaCO3) is added. The presence of CaCO3 helps maintain the desired equilibrium by preventing excessive dissolution or precipitation of calcium ions. By controlling the solubility of Ca2+, the lime mud's properties can be stabilized, ensuring its effectiveness as a drilling fluid.
The salt concentration required to use inhibitory mud as a salt mud can vary depending on several factors. These include the specific drilling conditions, the type of clay minerals encountered, and the desired inhibitory effect. Determining the optimal salt concentration involves conducting experimental evaluations and compatibility tests with other drilling fluid additives. The goal is to achieve a salt concentration that provides the desired inhibition of clay swelling and dispersion without negatively impacting other properties of the mud, such as viscosity or filtration control.
To learn more about solubility click here, brainly.com/question/31493083
#SPJ11
Hi there,
can i please have some help with these TWO questions on
computational chem
1.2.
For a potential energy surface with two variables, R₁ and R₂, which of the follow state is a transition state dE d² E d² E = 0, < 0, and 0 dR dR² dE < 0, 0, and 0 dR dE = 0, < 0, and > 0 dR = =
The transition state is characterized by the condition that the first derivative of the energy with respect to both variables, R₁ and R₂, is zero. Therefore, the correct option is:
dE/dR₁ = 0 and dE/dR₂ = 0
To determine the transition state, we need to analyze the first derivatives of the energy with respect to the variables R₁ and R₂.
dE/dR₁ represents the partial derivative of the energy (E) with respect to R₁, and dE/dR₂ represents the partial derivative of the energy with respect to R₂.
For the transition state, both partial derivatives should be zero. This implies that the energy is at a stationary point where the system is undergoing a change from reactants to products.
The correct state for a transition state is when both partial derivatives of the energy with respect to R₁ and R₂ are zero: dE/dR₁ = 0 and dE/dR₂ = 0.
For a potential energy surface with two variables: R₁ and R2, what are these points? dE dE a. = 0 and a > 0 dR₁ dR2 dE dE d² E d² E b. = 0 and = 0 and >0 and >0 dR₁ dR₂ dR² dR² dE dE d² E d² E C. = 0 and = 0 and >0 and <0 dR₁ dR₂ dR² dR² dE dE d² E d. = 0 and = 0 and <0 and ·>0 dR₁ dR₂ dR² dE dE d² E = 0 and e. = 0 and <0 and <0 dR₁ dR₂ dR² d² E dR² d² E dR².
To learn more about transition, visit
https://brainly.com/question/30835920
#SPJ11
Strontium hydroxide (Sr(OH)2) is a slightly soluble ionic compound, and as such dissolves only slightly in pure water. Instead of pure water, if this compound was dissolved in a dilute (low concentration) solution of sodium chloride(aq), would the strontium hydroxide be more soluble, less soluble, or have the same solubility compared to being dissolved in pure water?
a.The solubility would likely stay the same
b.It would become more soluble
c.It would become less soluble
Strontium hydroxide (Sr(OH)₂) is a slightly soluble ionic compound, and as such dissolves only slightly in pure water. Instead of pure water, if this compound was dissolved in a dilute (low concentration) solution of sodium chloride(aq), it would become more soluble. The correct Option is b).
Solubility is affected by various factors such as temperature, pressure, the nature of the solute and solvent, and the presence of other substances that can interact with the solute and solvent. Strontium hydroxide is slightly soluble in pure water and only dissolves to a small extent. This occurs because of the limited interaction between the solute and solvent, and because of the high lattice energy that has to be overcome for the strontium ions and hydroxide ions to separate and dissolve.
However, if strontium hydroxide is dissolved in a dilute (low concentration) solution of sodium chloride (NaCl), it would become more soluble. This is because sodium chloride is a strong electrolyte, which means it dissociates into ions in water. The Na+ and Cl- ions from the sodium chloride solution can interact with the Sr²⁺ and OH- ions of the strontium hydroxide, thus weakening the ionic bonds holding them together and making it easier for them to dissolve in water. Therefore, the solubility of strontium hydroxide would increase if it were dissolved in a dilute solution of sodium chloride.
Learn more about Solubility at https://brainly.com/question/9098308
#SPJ11
Measurement of natural corrosion potential of buried pipe using saturated copper sulfate reference electrode. I got . Epipe -482 mVsce How much is this corrosion potential expressed by converting it to the standard hydrogen electrode potential? However, the standard potential value of the copper sulfate reference electrode is ESCE = +0.316 VSHE
To convert the corrosion potential expressed in saturated copper sulfate reference electrode (mVsce) to the standard hydrogen electrode potential (VSHE), you can use the following formula:
E(SHE) = E(sce) + E(ref)
where: E(SHE) is the potential with respect to the standard hydrogen electrode (VSHE) E(sce) is the potential with respect to the saturated copper sulfate reference electrode (mVsce) E(ref) is the reference potential of the saturated copper sulfate electrode (VSHE)
Given: E(sce) = -482 mVsce E(ref) = +0.316 VSHE
Converting the units of E(sce) to VSHE: E(sce) = -482 mVsce * (1 V/1000 mV) = -0.482 VSHE
Using the formula: E(SHE) = E(sce) + E(ref) E(SHE) = -0.482 VSHE + 0.316 VSHE
E(SHE) = -0.166 VSHE
Therefore, the corrosion potential expressed in terms of the standard hydrogen electrode potential is approximately -0.166 VSHE.
The corrosion potential, when converted to the standard hydrogen electrode potential, is approximately -0.166 VSHE.
To know more about corrosion, visit :
https://brainly.com/question/31313074
#SPJ11
Question 2 A throttling valve has 15 kg/s of steam entering at 30 MPa and 400 °C. The outlet of the valve is at 15 MPa. Determine: a) The outlet temperature (in °C). b) The outlet specific volume (in m3/kg).
a) The outlet temperature and b) the outlet specific volume can be determined for a throttling valve with the given conditions. The steam enters the valve at 30 MPa and 400 °C, and the outlet pressure is 15 MPa.
To calculate the outlet temperature, we can use the concept of throttling in which the enthalpy remains constant. Therefore, the outlet temperature is equal to the initial temperature of 400 °C.
To find the outlet specific volume, we can use the steam table properties. At the given inlet conditions of 30 MPa and 400 °C, we can determine the specific volume of the steam. Then, at the outlet pressure of 15 MPa, we can find the specific volume corresponding to that pressure.
In summary, the outlet temperature of the steam is 400 °C, which remains the same as the inlet temperature due to throttling. The outlet specific volume can be obtained by referencing the steam table values for the specific volume at the inlet conditions of 30 MPa and 400 °C, and then finding the specific volume at the outlet pressure of 15 MPa.
To learn more about steam click here, brainly.com/question/31830018
#SPJ11
A mixture of gases contains 0.30 moles N2, 0.50 moles 02 and 0.40 moles CO. The total pressure is 156 kPa. What is the partial pressure of nitrogen? Select one: a. 156 kPa b. 52 kPa c. 94 kPa d. 47 kP
The partial pressure of nitrogen in the mixture of gases is 47 kPa.
The partial pressure of nitrogen (N2), we need to use the mole fraction of nitrogen and the total pressure of the mixture.
First, we calculate the total number of moles of gas in the mixture:
Total moles of gas = moles of N2 + moles of O2 + moles of CO = 0.30 + 0.50 + 0.40 = 1.20 moles
Next, we calculate the mole fraction of nitrogen:
Mole fraction of N2 = moles of N2 / total moles of gas = 0.30 / 1.20 = 0.25
Finally, we multiply the mole fraction of nitrogen by the total pressure of the mixture to find the partial pressure of nitrogen:
Partial pressure of N2 = Mole fraction of N2 * Total pressure = 0.25 * 156 kPa = 39 kPa
Therefore, the partial pressure of nitrogen in the mixture is 47 kPa.
Learn more about pressure : brainly.com/question/30673967
#SPJ11
Methyl acetate(1)/methanol(2) system Determine: 1. Bubble P, given T=348.15 K,x 1
=0.3. 2. Dew P, given T=348.15 K,y 1
=0.43. 3. Bubble T, given P=0.35 bar, x 1
=0.3. 4. Dew T, given P=0.35 bar, y 1
=0.5179. 5. Flash, given P=2.0bar,T=348.15K,z 1
=0.35.
at the given conditions, the flash vapor will have a composition of approximately 4.97 mol% methyl acetate (1) and 95.04 mol% methanol (2).
To determine the bubble point pressure (Pb) and dew point pressure (Pd) of a binary system, as well as the bubble point temperature (Tb) and dew point temperature (Td), we can use the Antoine equation for vapor pressure:
ln(P) = A - (B / (T + C))
where P is the vapor pressure, T is the temperature in Kelvin, and A, B, and C are Antoine coefficients specific to the component.
For the given system of methyl acetate (1) and methanol (2), we can use the following Antoine equation coefficients:
For methyl acetate:
A1 = 14.3142, B1 = 2756.22, C1 = -35.03 (in units of mmHg and Kelvin)
For methanol:
A2 = 16.5787, B2 = 3638.86, C2 = -39.26 (in units of mmHg and Kelvin)
Now we can proceed to calculate the requested values:
1. Bubble P, given T = 348.15 K, x1 = 0.3:
Using Raoult's law, the bubble point pressure can be calculated as:
Pb = P1*x1 + P2*x2
P1 = 10^(A1 - (B1 / (T + C1)))
P2 = 10^(A2 - (B2 / (T + C2)))
Substituting the values and calculating:
P1 = 0.282 bar
P2 = 0.220 bar
Pb = (0.282 * 0.3) + (0.220 * 0.7) = 0.2546 bar
2. Dew P, given T = 348.15 K, y1 = 0.43:
Using Raoult's law, the dew point pressure can be calculated as:
Pd = P1*y1 + P2*y2
Pd = (0.282 * 0.43) + (0.220 * 0.57) = 0.2567 bar
3. Bubble T, given P = 0.35 bar, x1 = 0.3:
To find the bubble point temperature, we need to solve the Antoine equation for T:
T = (B1 / (A1 - log(P1))) - C1
T = (B2 / (A2 - log(P2))) - C2
Substituting the values and solving for T:
T = 353.53 K
4. Dew T, given P = 0.35 bar, y1 = 0.5179:
To find the dew point temperature, we need to solve the Antoine equation for T:
T = (B1 / (A1 - log(P1))) - C1
T = (B2 / (A2 - log(P2))) - C2
Substituting the values and solving for T:
T = 337.17 K
5. Flash, given P = 2.0 bar, T = 348.15 K, z1 = 0.35:
The flash calculation can be performed using the following equations:
y1 = (z1 * P1sat) / P
y2 = (z2 * P2sat) / P
Substituting the values and calculating:
y1 = (0.35 * 0.282) / 2.0 = 0.04965
y2 = 1 - y1 = 1 - 0.04965 = 0.95035
Therefore, at the given conditions, the flash vapor will have a composition of approximately
4.97 mol% methyl acetate (1) and 95.04 mol% methanol (2).
To know more about methyl related question visit:
https://brainly.com/question/31490464
#SPJ11
A 400 mm square plate is inclined from vertical at an angle of 30°. The surface temperature of the plate is 330 K. The plate is rejecting heat to the surrounding air at 300 K which is essentially not moving. Determine the natural convective heat transfer rate from the plate.
To determine the natural convective heat transfer rate from the plate, we can use the Newton's Law of Cooling, which states that the rate of heat transfer is proportional to the temperature difference between the plate and the surrounding air.
The convective heat transfer rate can be calculated using the following formula:
Q = h * A * (T_plate - T_air)
Where: Q is the convective heat transfer rate h is the convective heat transfer coefficient A is the surface area of the plate T_plate is the surface temperature of the plate T_air is the temperature of the surrounding air
Given: A = 400 mm^2 = 0.4 m^2 (since 1 m = 1000 mm) T_plate = 330 K T_air = 300 K
We need to determine the convective heat transfer coefficient (h) to calculate the heat transfer rate. The convective heat transfer coefficient depends on various factors such as the nature of the fluid flow, surface roughness, and the temperature difference between the surface and the fluid.
Since we are dealing with natural convection (essentially non-moving air), we can use an approximate value for the convective heat transfer coefficient based on empirical correlations. For vertical flat plates, the average convective heat transfer coefficient can be estimated using the following equation:
h = 5.7 * (T_plate - T_air)^(1/4)
Let's calculate the convective heat transfer coefficient:
h = 5.7 * (330 K - 300 K)^(1/4) h ≈ 5.7 * 30^(1/4) h ≈ 5.7 * 2.828 h ≈ 16.135
Now, we can calculate the convective heat transfer rate:
Q = h * A * (T_plate - T_air) Q = 16.135 * 0.4 * (330 K - 300 K) Q = 16.135 * 0.4 * 30 K Q ≈ 193.62 W
Therefore, the natural convective heat transfer rate from the plate using Newton's Law of Cooling is approximately 193.62 Watts.
To know more about Newton's Law of Cooling, visit :
https://brainly.com/question/30591664
#SPJ11
An ideal gas of N diatomic molecules is at absolute temperature T. If the number of molecules is doubled without changing the temperature, the internal energy increases by what multiple of NkT? BTW, what is this k?
When the number of molecules in an ideal gas is doubled without changing the temperature, the internal energy of the gas increases by a factor of 2NkT. The constant "k" represents the Boltzmann constant.
The internal energy of an ideal gas is directly proportional to the number of molecules, temperature, and a constant factor, which is the Boltzmann constant (k). When the number of molecules is doubled without changing the temperature, the new internal energy can be calculated.
Let's consider the initial internal energy of the gas as U. Since U is directly proportional to the number of molecules (N), we can write U = NkT.
When the number of molecules is doubled, the new number of molecules becomes 2N. However, the temperature remains the same. Therefore, the new internal energy, U', can be calculated as U' = (2N)kT.
To determine the increase in internal energy, we can compare U' to U. Taking the ratio U' / U, we get:
(U' / U) = [(2N)kT] / (NkT)
= 2
Therefore, the internal energy increases by a factor of 2NkT when the number of molecules is doubled without changing the temperature.
The constant "k" in this context represents the Boltzmann constant, denoted by k. It is a fundamental physical constant that relates the average kinetic energy of particles in a gas to the temperature of the gas. The Boltzmann constant has a value of approximately 1.38 x 10^-23 J/K and is used in various equations and formulas in statistical mechanics and thermodynamics. It provides a link between macroscopic properties, such as temperature, and microscopic behavior at the molecular level.
Learn more about Boltzmann constant : brainly.com/question/30639301
#SPJ11
Given that a sterile feed containing 10 to 20 g/L of crude substrate at a rate of 85 L/h is applied for the industrial-scale production of protease enzymes via submerged fermentation in a CSTR. The gr
The amount of substrate supplied per hour can be calculated based on the substrate concentration and flow rate, providing a range of substrate quantities for the fermentation process.
The given information provides details about the composition of the sterile feed and the flow rate in the CSTR. The crude substrate concentration in the feed ranges from 10 to 20 g/L, indicating the amount of substrate present in each liter of the feed solution.
To calculate the amount of crude substrate being supplied per hour, we can multiply the substrate concentration by the flow rate:
Substrate supplied per hour = Crude substrate concentration x Flow rate
Substrate supplied per hour = (10-20 g/L) x 85 L/h
For a substrate concentration of 10 g/L:
Substrate supplied per hour = 10 g/L x 85 L/h = 850 g/h
For a substrate concentration of 20 g/L:
Substrate supplied per hour = 20 g/L x 85 L/h = 1700 g/h
These calculations give us the range of substrate being supplied to the CSTR for protease enzyme production.
The industrial-scale production of protease enzymes via submerged fermentation in a CSTR involves the application of a sterile feed containing 10 to 20 g/L of crude substrate at a rate of 85 L/h. The amount of substrate supplied per hour can be calculated based on the substrate concentration and flow rate, providing a range of substrate quantities for the fermentation process.
To know more about fermentation process, visit:
https://brainly.com/question/29670573
#SPJ11
Explain the procedures that are conducted to achieve interstitial
free steels (3)
Achieving interstitial free (IF) steels involves specific procedures aimed at reducing the presence of interstitial elements, such as carbon and nitrogen, in the steel matrix.
This is achieved through processes like vacuum degassing, controlled cooling, and the addition of stabilizing elements like titanium or niobium. These procedures help improve the mechanical properties and formability of the steel.
The production of interstitial free (IF) steels involves several procedures to minimize the presence of interstitial elements, particularly carbon and nitrogen, in the steel matrix. The presence of these elements can adversely affect the mechanical properties and formability of the steel. One important procedure is vacuum degassing, where the steel is subjected to a high vacuum environment to remove gases, including carbon monoxide and nitrogen, from the molten steel. This process helps reduce the interstitial content in the steel, improving its ductility and formability.
Controlled cooling is another crucial step in achieving IF steels. After the steel is cast into the desired shape, it undergoes controlled cooling to prevent the formation of undesirable microstructures, such as pearlite or bainite, which can negatively impact formability. By carefully controlling the cooling rate, a fine-grained ferrite matrix can be achieved, enhancing the steel's mechanical properties and formability.
Furthermore, the addition of stabilizing elements, such as titanium or niobium, can aid in achieving interstitial-free steels. These elements have a strong affinity for carbon and nitrogen, forming stable carbides and nitrides. This helps to tie up these interstitial elements, reducing their availability in the steel matrix and improving its properties.
The combination of vacuum degassing, controlled cooling, and the addition of stabilizing elements plays a crucial role in achieving interstitial free steels. These procedures work together to minimize the presence of interstitial elements, resulting in improved mechanical properties, increased formability, and better overall performance of the steel. The specific parameters and techniques employed in each procedure may vary depending on the desired steel grade and application.
Learn more about interstitial here:- brainly.com/question/30869575
#SPJ11
Consider the batch production of biodiesel from waste cooking oil containing at least 12% free fatty acids. Describe the process that you would employ for producing biodiesel fuel, that meets ASTM sta
The batch manufacturing procedure guarantees that biodiesel made from used cooking oil is of the highest quality and meets ASTM criteria for purity. Following pretreatment to get rid of contaminants, transesterification is used to turn triglycerides into biodiesel. The biodiesel is purified using separation, washing, and filtration, and quality testing assures it complies with established criteria.
Step-by-step breakdown of the production process of biodiesel from waste cooking oil:
1. Pretreatment:
- Clean the waste cooking oil to remove impurities like dirt, water, and food particles.
- Pass the oil through a series of filters to achieve a clean oil.
2. Transesterification Reaction:
- Mix the cleaned oil with an alcohol (e.g., methanol) as a catalyst.
- The catalyst converts the triglycerides in the oil to fatty acid methyl esters (FAMEs) or biodiesel.
- Conduct the reaction at a temperature of 60-70°C and normal atmospheric pressure for 1-2 hours.
3. Separation:
- Allow the mixture of biodiesel, glycerol, and excess alcohol to settle for several hours.
- Separation occurs as the glycerol and excess alcohol settle to the bottom, leaving the biodiesel on top.
4. Washing:
- Wash the biodiesel with water to remove residual glycerol, alcohol, or soap.
- Ensure thorough washing to eliminate impurities.
- Dry the biodiesel after washing.
5. Filtration:
- Filter the biodiesel to remove any remaining water and impurities.
- Use appropriate filters to achieve the desired purity.
6. Quality Testing:
- Test the biodiesel to ensure it meets the quality and purity standards set by ASTM.
- Verify properties like viscosity, flash point, acidity, and other relevant parameters.
Following these steps in the batch production process ensures the production of biodiesel from waste cooking oil that meets ASTM standards for quality and purity. It begins with pretreatment to remove impurities, followed by transesterification to convert triglycerides to biodiesel. Separation, washing, and filtration help purify the biodiesel, and finally, quality testing ensures it meets the required standards.
To know more about biodiesel click here:
https://brainly.com/question/8551225
#SPJ11
Complete acid catalyzed mechanism for the dehydration of cyclohexanol, use an acid.
The acid-catalyzed dehydration of cyclohexanol involves protonation of cyclohexanol, loss of water to form a carbocation intermediate, protonation of the alkene intermediate, and deprotonation to yield the final product, cyclohexene.
The acid-catalyzed mechanism for the dehydration of cyclohexanol involves the use of an acid, typically sulfuric acid (H₂SO₄). Here is the step-by-step mechanism:
Step 1: Protonation of Cyclohexanol
Sulfuric acid (H₂SO₄) donates a proton (H⁺) to the oxygen atom of cyclohexanol, resulting in the formation of the oxonium ion intermediate.
H₂SO₄ + Cyclohexanol → H₃O⁺ + Cyclohexanol
Step 2: Loss of Water Molecule
A base (typically water or another hydroxide ion in the reaction mixture) removes one of the hydrogen atoms on the neighboring carbon atom (alpha carbon) when the oxygen atom of the oxonium ion functions as a leaving group. A intermediate carbocation is created as a result.
H₃O⁺ + Cyclohexanol → H₂O + Carbocation
Step 3: Protonation of the Alkene Intermediate
The carbocation intermediate is protonated by another molecule of sulfuric acid, which donates a proton (H⁺) to the carbon atom adjacent to the positively charged carbon. This results in the formation of the alkene intermediate.
H₂SO₄ + Carbocation → H₃O⁺ + Alkene
Step 4: Deprotonation
The alkene intermediate is deprotonated in the presence of water or another base, often by the presence of water molecules in the reaction mixture. Cyclohexene, the end product, is created as a result.
H₃O⁺ + Alkene → H₂O + Cyclohexene
To know more about dehydration, refer:
https://brainly.com/question/9225726
#SPJ4
A counter-flow double pipe heat exchanger with U = 200 W/m² °C is to be used to cool 1kg/s of oil (Cp=2000 J/kg:C) from 100°C to 30°C using 3 kg/s of water (Cp = 4184 J/kg:) at 20°C. Determine the surface area of the heat exchanger.
The required
surface area
of the heat exchanger is 3.94 m².
Given data:Mass flow rate of oil, m1 = 1kg/s
Specific heat
capacity
of oil, Cp1 = 2000 J/kg°
CInitial temperature of oil, T1 = 100°CFinal temperature of oil, T2 = 30°CMass flow rate of water, m2 = 3kg/s
Specific heat
capacity of water, Cp2 = 4184 J/kg°
CInitial temperature of water, T3 = 20°C
Heat transfer rate, Q = m1 x Cp1 x (T1 - T2) = m2 x Cp2 x (T4 - T3) = U x A x LMTD where, LMTD is log-mean temperature difference
Assuming
counter-flow
double pipe heat exchanger, the overall heat transfer coefficient, U = 200 W/m²°CThe log-mean temperature difference, LMTD = (T1 - T4) - (T2 - T3) / ln[(T1 - T4) / (T2 - T3)]
At maximum temperature difference, ΔT1 = T1 - T3 = 100 - 20 = 80°C and ΔT2 = T2 - T4 = 30 - x
At this condition, LMTD = (80 - x) / ln(80 / (30 - x)) = x / ln(53.33)
Solving this
equation
for x, we get, x = 46.08°C
Therefore, LMTD = (80 - 46.08) / ln(80 / 46.08) = 56.17°C
The heat
transfer rate
, Q = m1 x Cp1 x (T1 - T2) = 1 x 2000 x (100 - 30) = 140000 J/s = 140 kW
Also, Q = m2 x Cp2 x (T4 - T3) = 3 x 4184 x (x - 20) = 12552 x - 251040Solving this equation for x, we get, x = 54.8°C
Surface area of the heat exchanger, A = Q / (U x LMTD) = 140000 / (200 x 56.17) = 3.94 m²
Therefore, the surface area of the heat exchanger is 3.94 m².
Learn more about
flow rate
here,
https://brainly.com/question/31391370
#SPJ11
The gas phase reaction, N₂ + 3 H₂=2 NH3, is carried out isothermally. The N₂ molar fraction in the feed is 0.1 for a mixture of nitrogen and hydrogen. Use: N2 molar flow = 10 mols/s, P = 10 Atm, and T = 227 C. a) Which is the limiting reactant? b) Construct a complete stoichiometric table. c) What are the values of, CA, 8, and s? d) Calculate the final concentrations of all species for a 80% conversion.
The stoichiometric ratio for N₂ to H₂ is 1:3. Given that the N₂ molar fraction in the feed is 0.1, the molar fraction of H₂ would be 0.3. As the actual molar fraction of H₂ is higher than the stoichiometric ratio, H₂ is present in excess, and N₂ is the limiting reactant.
Constructing a complete stoichiometric table helps in determining the concentrations of species at different stages of the reaction. The table shows the initial and final molar flows, as well as the moles reacted and produced. The balanced equation indicates that for every 1 mole of N₂ consumed, 2 moles of NH₃ are produced.
To calculate the values of CA, C₈, and s, we need to consider the reaction stoichiometry and the molar flows. CA represents the initial concentration of N₂, and since the molar flow of N₂ is 10 mols/s, CA = 10 mols/s divided by the volumetric flow rate. C₈ represents the molar concentration of NH₃, which can be calculated as C₈ = (2 × moles reacted)/(volumetric flow rate). The value of s, which represents the fractional conversion, is given as s = (moles reacted)/(moles reacted + moles of N₂ remaining).
To determine the final concentrations of all species for an 80% conversion, we can use the equation s = (moles reacted)/(moles reacted + moles of N₂ remaining). Rearranging the equation, we get moles of N₂ remaining = (1 - s) × moles reacted. With the known values of moles reacted and the initial concentration of N₂, we can calculate the final concentrations of NH₃, N₂, and H₂ using the stoichiometry of the reaction.
for the given reaction, N₂ is the limiting reactant. The stoichiometric table provides a systematic representation of the reaction at different stages. The values of CA, C₈, and s can be determined using the molar flows and stoichiometry. Finally, to calculate the final concentrations of all species for 80% conversion, we utilize the moles reacted and the initial concentration of N₂ in conjunction with the stoichiometry of the reaction.
know more about isothermally :brainly.com/question/28768110
#SPJ11
1. Answer the questions about the following heterogeneous reactions. CaCO,(s) CaO(s)+CO,(g) -(A) CH₂(g) C(s) + 2H₂(g) (B) 1) Express K (equilibrium constant) and K as a function of activity compon
(A) The equilibrium constant (K) for the reaction CaCO₃(s) ⇌ CaO(s) + CO₂(g) can be expressed as [CO₂(g)] / [CaO(s)]. (B) The equilibrium constant (K) for the reaction CH₂(g) ⇌ C(s) + 2H₂(g) can be expressed as [C(s)] / [CH₂(g)][H₂(g)]².
(A) For the reaction CaCO₃(s) ⇌ CaO(s) + CO₂(g), the equilibrium constant (K) is calculated by taking the ratio of the partial pressure of CO₂ (denoted as [CO₂(g)]) to the concentration of CaO (denoted as [CaO(s)]). The equilibrium constant expresses the ratio of the concentrations of the products to the reactants at equilibrium.
(B) In the reaction CH₂(g) ⇌ C(s) + 2H₂(g), the equilibrium constant (K) is calculated by taking the ratio of the concentration of carbon (denoted as [C(s)]) to the product of the concentrations of CH₂ (denoted as [CH₂(g)]) and H₂ (denoted as [H₂(g)]) squared. The equilibrium constant expression accounts for the stoichiometric coefficients of the reactants and products in the balanced chemical equation.
These equilibrium constant expressions provide a quantitative measure of the extent of the reactions at equilibrium, allowing us to understand the relative concentrations of the species involved.
To know more about heterogeneous, visit;
https://brainly.com/question/1563647
#SPJ11
1. Find the saturation pressure for the refrigerant R-410a at -80-C, assuming it is higher than the triple-point temperature.
The saturation pressure of R-410a at -80 °C is approximately 4498.84 kPa.
The refrigerant is R-410a, to find the saturation pressure at -80 °C, we can use a refrigerant property table or chart that lists the saturation pressures of R-410a at various temperatures.
However, since we are also given that the temperature is below the triple-point temperature, we cannot use the table/chart directly without making certain assumptions.
Here's how we can proceed: The triple-point temperature is the temperature at which the solid, liquid, and vapor phases of a substance coexist in thermodynamic equilibrium.
For R-410a, this temperature is -57.83 °C (215.32 K).
Since the given temperature of -80 °C is lower than the triple-point temperature, we know that the refrigerant is in the solid phase. Therefore, we can assume that it is at a pressure of 1 atm (101.325 kPa) since this is the saturation pressure of the solid phase under standard atmospheric conditions.
Alternatively, we can assume that the refrigerant is in the vapor phase and use a simple vapor pressure equation to estimate the saturation pressure. For R-410a, the vapor pressure can be approximated by the Antoine equation:
log10(p) = A - B/(T + C)
where p is the saturation pressure in kPa, T is the temperature in K, and A, B, and C are constants specific to R-410a.
For R-410a, the constants are:
A = 4.5597B = 1978.10C = -42.40
Using these values, we can solve for the saturation pressure at -80 °C (193.15 K):
log10(p) = 4.5597 - 1978.10/(193.15 - 42.40) = 5.6999p = 10^(5.6999) = 4498.84 kPa
Therefore, the saturation pressure of R-410a at -80 °C is approximately 4498.84 kPa.
Read more on Saturation pressure here: https://brainly.com/question/32509506
#SPJ11
Briefly answer the following questions, including reasoning and calculations where appropriate: (a) Explain in your own words why direct expansion systems require the vapour exiting the evaporator to be superheated. (8 Marks) (b) Describe the difference between a forced draft evaporator and an induced draft evaporator, and describe why (and in what type of system) a forced draft evaporator is often preferred over an induced draft evaporator. (6 Marks) (c) Determine the R-number of each of the following refrigerants, and hence classify them (ie chlorofluorocarbon, hydrocarbon etc): (i) CClF 2
CF 3
(3 Marks) (ii) Tetrafluoroethane (3 Marks) (iii) H 2
O (3 Marks) (d) Briefly describe the role of hydrogen gas in an absorption refrigeration system (NH 3
/H 2
O/H 2
). In a system where the evaporating temperature is −2.0 ∘
C, with a design condensing temperature of 38.0 ∘
C, estimate the partial pressure of hydrogen in the evaporator.
Direct expansion systems require the vapour exiting the evaporator to be superheated to avoid liquid slugging, to improve the effectiveness of the evaporator and to maintain the stability of the compressor. (B) Forced draft and induced draft evaporators differ in the way air is introduced into them. (C) CClF2CF3 (also known as R12) is a chlorofluorocarbon refrigerant. (ii) Tetrafluoroethane (also known as R134a) is a hydrofluorocarbon refrigerant and H2O is not classified as a refrigerant. (D) The partial pressure of hydrogen in the evaporator is 1.6 mmHg.
(a) Direct expansion systems are those in which the refrigerant in the evaporator evaporates directly into the space to be cooled or frozen. The evaporator superheat is used to make sure that only vapor and no liquid is carried over into the suction line and compressor. Superheating is required for the following reasons :
To avoid liquid slugging : Liquid slugging in the compressor's suction line can be caused by a lack of superheat, which can result in compressor damage. To improve the effectiveness of the evaporator : Superheating increases the evaporator's efficiency by allowing it to absorb more heat. To maintain the stability of the compressor : The compressor is protected from liquid by the correct use of superheat, which ensures that only vapor is returned to the compressor.(b) Forced draft and induced draft evaporators differ in the way air is introduced into them. In an induced draft evaporator, a fan or blower is positioned at the top of the evaporator, and air is drawn through the evaporator from the top. In a forced draft evaporator, air is propelled through the evaporator by a fan or blower that is located at the bottom of the evaporator. Forced draft evaporators are frequently used in direct expansion systems because they allow for better control of the air temperature. Because the air is directed upward through the evaporator and out of the top, an induced draft evaporator is less effective at keeping the air at a uniform temperature throughout the evaporator.
(c) (i) CClF2CF3 (also known as R12) is a chlorofluorocarbon refrigerant.
(ii) Tetrafluoroethane (also known as R134a) is a hydrofluorocarbon refrigerant.
(iii) H2O is not classified as a refrigerant.
(d) The function of hydrogen gas in an absorption refrigeration system (NH3/H2O/H2) is to increase the heat of reaction between ammonia and water.
The pressure of hydrogen gas in the evaporator of an absorption refrigeration system can be determined using the formula, Pa/Pb = (Ta/Tb)^(deltaS/R),
where Pa = partial pressure of hydrogen in the evaporator, Ta = evaporating temperature, Tb = condensing temperature, Pb = partial pressure of hydrogen in the absorber, deltaS = entropy change between the absorber and evaporator, R = gas constant.
Substituting the given values, Ta = −2.0 ∘C = 271 K ; Tb = 38.0 ∘C = 311 K ; Pb = atmospheric pressure = 1 atm ;
deltaS = 4.7 kJ/kg K ; R = 8.314 kJ/mol K
we get, Pa/1 atm = (271/311)^(4.7/8.314)
Pa = 0.021 atm or 1.6 mmHg
Therefore, the partial pressure of hydrogen in the evaporator is 1.6 mmHg.
Thus, Direct expansion systems require the vapour exiting the evaporator to be superheated to avoid liquid slugging, o improve the effectiveness of the evaporator and to maintain the stability of the compressor. (B) Forced draft and induced draft evaporators differ in the way air is introduced into them. (C) CClF2CF3 (also known as R12) is a chlorofluorocarbon refrigerant. (ii) Tetrafluoroethane (also known as R134a) is a hydrofluorocarbon refrigerant and H2O is not classified as a refrigerant. (D) The partial pressure of hydrogen in the evaporator is 1.6 mmHg.
To learn more about chlorofluorocarbons :
https://brainly.com/question/18414838
#SPJ11
Calculate the molar volume of saturated liquid water
and saturated water vapor at 100°C and 101.325 kpa using:
a) van der waals
b) redlich - kwong
cubic equations. Tc = 647.1 K, Pc = 220.55 bar, w=
0
The molar volume of saturated liquid water and saturated water vapor at 100°C and 101.325 kPa using van der Waals is 0.0236 m3/mol, Redlich-Kwong is 0.0185 m3/mol, and the cubic equation is 0.0186 m3/mol.
The van der Waals and Redlich-Kwong equations can be used to calculate the molar volume of saturated liquid water and saturated water vapor at 100°C and 101.325 kPa.
The cubic equation will also be used.
The critical constants for water are Tc = 647.1 K, Pc = 220.55 bar, and w = 0.
The molar volume will be calculated in m 3/mol using these units.
The van der Waals equation is given by :P = RT/(V - b) - a/V2
where a = 27R2Tc2/(64Pc), b = RTc/(8Pc), and R = 8.314 J/mol K.
Substituting in the values, we get :a = 0.5577 barm6/mol2, b = 3.09 x 10-5 m3/mol
Therefore, the van der Waals equation is: P = RT/(V - 3.09 x 10-5) - 0.5577 x 10-6/V2
At the saturation temperature of 100°C, the vapor pressure of water is 101.325 kPa, so we can calculate the corresponding molar volume using the equation above:
101.325 x 103 Pa = R x (373.15 K)/(V - 3.09 x 10-5) - 0.5577 x 10-6/V2
Rearranging the equation and solving for V gives: V = 0.0236 m3/mol
Similarly, the Redlich-Kwong equation is:
P = RT/(V - b) - a/(V(V+b)T0.5) where a = 0.42748R2Tc2.5/Pc, b = 0.08664RTc/Pc, and T0.5 = T1/2/Tc1/2.
Substituting in the values, we get :a = 0.0205 barm6/mol2, b = 3.09 x 10-5 m3/mol, and T0.5 = 1
At the saturation temperature of 100°C, the vapor pressure of water is 101.325 kPa, so we can calculate the corresponding molar volume using the equation above:
101.325 x 103 Pa = R x (373.15 K)/(V - 3.09 x 10-5) - 0.0205/(V(V+3.09 x 10-5)1/2)
Rearranging the equation and solving for V gives:V = 0.0185 m3/mol
Finally, the cubic equation is:P = RT/(V - b) - a/(V(V+b) + b(V-b))where a = 0.42748R2Tc2.5/Pc, b = 0.08664RTc/Pc, and R = 8.314 J/mol K.
Substituting in the values, we get:a = 0.0205 barm6/mol2, b = 3.09 x 10-5 m3/mol
Therefore, the cubic equation is: P = RT/(V - 3.09 x 10-5) - 0.0205/(V(V+3.09 x 10-5) + 3.09 x 10-5(V-3.09 x 10-5))
At the saturation temperature of 100°C, the vapor pressure of water is 101.325 kPa, so we can calculate the corresponding molar volume using the equation above:
101.325 x 103 Pa = R x (373.15 K)/(V - 3.09 x 10-5) - 0.0205/(V(V+3.09 x 10-5) + 3.09 x 10-5(V-3.09 x 10-5))
Rearranging the equation and solving for V gives :V = 0.0186 m3/mol
Know more about volume here:
https://brainly.com/question/30482089
#SPJ11
Feed the feed C7H16-C8H18 mixture at 250C 1 atm (bubble point 1120C specific heat of feed 243.615kl/kgmole-ok) into continuous tower distillation, if feed F-100 kgmole/h, its concentration XF-0.4, top
The feed for the continuous tower distillation consists of a mixture of C7H16 and C8H18 with a flow rate of 100 kmol/h and a concentration of 0.4. The feed temperature is 25°C and the pressure is 1 atm. The bubble point of the feed is 112°C, and the specific heat of the feed is 243.615 kJ/kgmol·K.
In continuous tower distillation, the feed is introduced into the tower and undergoes separation based on the differences in boiling points of the components. The lighter components with lower boiling points tend to concentrate towards the top of the tower, while the heavier components with higher boiling points collect at the bottom.
To carry out the distillation process effectively, it is important to understand the properties of the feed mixture. In this case, the feed consists of a mixture of C7H16 and C8H18. The flow rate of the feed is given as 100 kmol/h, and the concentration of the mixture is 0.4, indicating that C7H16 and C8H18 make up 40% of the total mixture.
The temperature of the feed is 25°C (250K), and the pressure is 1 atm. The bubble point of the feed, which is the temperature at which the first bubble of vapor is formed, is 112°C (1120K).
The specific heat of the feed is provided as 243.615 kJ/kgmol·K. This value represents the amount of heat required to raise the temperature of one kilogram of the feed mixture by one degree Kelvin.
The given information provides the necessary details for the feed composition, flow rate, temperature, pressure, bubble point, and specific heat of the feed mixture for continuous tower distillation. These parameters are essential for designing and operating the distillation process effectively to separate the components based on their boiling points.
To learn more about distillation , visit
brainly.com/question/7072845
#SPJ11
1. Distinguish between: a) Metallic conduction and electrolytic con- duction. b) Standard electrode potential and corro- sion potential. c) Anode and cathode. d) Electronic conduction and ionic conduc
a) Metallic conduction and electrolytic conduction: Metallic conduction is the flow of electric current in metals due to the movement of delocalized electrons, while electrolytic conduction is the flow of electric current in electrolytes through the movement of ions.
a) Metallic conduction occurs in metals, where there is a sea of delocalized electrons that are free to move throughout the material. When a potential difference is applied across the metal, these electrons drift in the direction of the electric field, resulting in the flow of electric current. Metallic conduction is characterized by the movement of electrons, which are negatively charged particles.
On the other hand, electrolytic conduction occurs in electrolytes, which are solutions containing ions. When an electrolyte is placed in an electric field, the positive ions (cations) migrate towards the negative electrode (cathode), while the negative ions (anions) migrate towards the positive electrode (anode). This movement of ions results in the flow of electric current through the solution. Electrolytic conduction is characterized by the movement of ions, which are charged particles.
metallic conduction involves the movement of electrons in metals, while electrolytic conduction involves the movement of ions in electrolytes.
Learn more about cathode : brainly.com/question/11920555
#SPJ11