The rate constant of reaction Na2 → 2Na, at a temperature of 1000K and constant pressure is 0.055 min⁻¹.
The dissociation reaction in the vapor phase of Na2 → 2Na takes place isothermally in a batch reactor at a temperature of 1000 K and constant pressure.
The feed stream consists of an equimolar mixture of reactant and carrier gas. The amount was reduced to 45% in 10 minutes. The reaction follows an elementary rate law.
For the given dissociation reaction:
Na2(g) → 2Na(g)
The rate law for an elementary reaction is given by:
rate = k [A]ⁿ
where,k = rate constant[A] = concentration of reactant
n = order of the reaction
For the given reaction:
rate = k [Na2]¹
where the concentration of Na2 is represented by [Na2]¹.
The given reaction is an isothermal process, which means the temperature (T) is constant.
The concentration of reactant (Na2) decreases by 55% or 0.55 in 10 minutes.
So, the fraction of Na2 remaining after 10 minutes = (1 - 0.55) = 0.45 or 45%Initial concentration of Na2 = 1M
The final concentration of Na2 = 0.45M
The change in concentration of Na2 = (1 - 0.45) = 0.55M
The time is taken to reach the final concentration = 10 minutes
Let’s calculate the rate constant of the reaction using the formula:
Rate = k [Na2]¹
k = Rate / [Na2]¹
From the rate law, rate = k [Na2]¹
Substituting the given values of rate and concentration,
Rate = (0.55 M / 10 min) = 0.055 M/min
k = Rate / [Na2]¹= 0.055 M/min / 1 M
= 0.055 min⁻¹
The rate constant of the reaction is 0.055 min⁻¹.
Learn more about rate constant here:
https://brainly.com/question/26127112
#SPJ11
The element bromine is composed of a mixture of atoms of which 50.67% of all Br atoms are 79Br with a mass of 78.9183 amu and 49.33 % are 81Br with a mass of 80.9163 amu. Calculate the average atomic mass of bromine
The average atomic mass of bromine is 79.868 amu.
The element bromine is composed of a mixture of atoms of which 50.67% of all Br atoms are 79Br with a mass of 78.9183 amu and 49.33 % are 81Br with a mass of 80.9163 amu.
Calculate the average atomic mass of bromine.Bromine has two isotopes, which are bromine-79 and bromine-81. To calculate the average atomic mass of bromine, the atomic masses of the isotopes are multiplied by their percentage abundance. The following formula is used to calculate the average atomic mass of bromine:
Average atomic mass = (percentage abundance of isotope 1 x atomic mass of isotope 1) + (percentage abundance of isotope 2 x atomic mass of isotope
The percentage abundance of bromine-79 is 50.67%, and its atomic mass is 78.9183 amu.
The percentage abundance of bromine-81 is 49.33%, and its atomic mass is 80.9163 amu.
The average atomic mass of bromine can be calculated as follows:
Average atomic mass of bromine = (0.5067 x 78.9183 amu) + (0.4933 x 80.9163 amu)
= 39.9877 amu + 39.8803 amu
= 79.868 amu
To know more about atomic mass visit:
https://brainly.com/question/29117302
#SPJ11
A. Describe the operation of a Mitsubishi smelting furnace. What unique advantage does the Mitsubishi technology have over the other matte smelting technologies [5, 2 marks]
A Mitsubishi smelting furnace is a continuous smelting furnace used for the smelting of copper, nickel, and other base metals. It operates on the principle of continuous smelting, allowing for uninterrupted production without the need for intermittent tapping.
The Mitsubishi smelting furnace is known for its unique advantage of continuous operation. Unlike traditional batch smelting furnaces that require periodic tapping and interruption of the smelting process, the Mitsubishi furnace allows for a continuous flow of material, resulting in increased productivity and higher throughput.
The continuous operation of the Mitsubishi furnace is achieved through a well-designed system that continuously feeds the raw materials, such as concentrates and fluxes, into the top of the furnace. Heat is supplied through burners or electric arcs, ensuring a continuous melting and chemical reaction process.
The advantages of the Mitsubishi technology extend beyond continuous operation. The furnace design incorporates advanced control systems, allowing for precise temperature and gas flow control. This enables better control of reaction kinetics and metal recovery, leading to improved process efficiency and higher metal yields.
Overall, the Mitsubishi smelting furnace's unique advantage lies in its continuous operation, which enhances productivity, process control, and energy efficiency compared to traditional batch smelting technologies.
To learn more about smelting furnace here
https://brainly.com/question/28950220
#SPJ4
f) Describe the likely sequence of events leading to a BLEVE incident and explain why this is so catastrophic with reference to one of the incidents studied in the module.
BLEVE incidents occur when pressurized containers are exposed to intense heat, leading to container weakening, pressure buildup, and eventually a catastrophic explosion.
A BLEVE (Boiling Liquid Expanding Vapor Explosion) incident typically occurs in situations involving pressurized containers, such as propane tanks or vessels carrying flammable liquids. The sequence of events leading to a BLEVE can be as follows:
Heat Source: The initial trigger is a significant heat source, such as a fire, that exposes the pressurized container to intense heat.
Container Weakening: The heat causes the container’s structural integrity to weaken. The metal may start to expand and lose strength, leading to potential ruptures or failures.
Pressure Buildup: As the container heats up, the temperature of the liquid inside rises, resulting in the generation of vapor or gas. This leads to an increase in pressure within the container.
Critical Pressure Exceeded: If the heat and pressure continue to rise beyond the container’s critical pressure, it reaches a point where it can no longer contain the pressure, and a catastrophic failure occurs.
Explosion: The sudden rupture of the container releases a massive amount of highly pressurized gas and vapor, resulting in an explosion. The explosion is accompanied by a fireball and a shockwave, which can cause extensive damage and pose a significant threat to nearby structures, people, and the environment.
A notable incident studied in the module is the 2013 Lac-Mégantic rail disaster in Canada. A train carrying crude oil derailed and caught fire, leading to a series of catastrophic BLEVEs. The heat from the fire caused the pressurized tanks to rupture and release a massive amount of highly flammable vapor. The ensuing explosions destroyed several buildings, ignited further fires, and resulted in the tragic loss of 47 lives.
Learn more about Pressure here: brainly.com/question/30673967
#SPJ11
Write the conjugate acid of each of the following bases (1) (iii) NO2 H2PO4 он" ASO42-
The conjugate acid of a base is the species formed when the base accepts a proton (H+). The base (iii) is NO2-. Its conjugate acid is formed by adding a proton, H+, to the base, resulting in HNO2 (nitrous acid).
The base H2PO4- is the dihydrogen phosphate ion. Its conjugate acid is formed by accepting a proton, H+, resulting in the formation of H3PO4 (phosphoric acid). The base OH- is the hydroxide ion. Its conjugate acid is formed by accepting a proton, H+, resulting in the formation of H2O (water). The base ASO42- is the arsenate ion. Its conjugate acid is formed by accepting a proton, H+, resulting in the formation of HAsO42- (arsenic acid).
In summary, the conjugate acids of the given bases are: (iii) NO2- -> HNO2. H2PO4- -> H3PO4; OH- -> H2O; ASO42- -> HAsO42-.
To learn more about conjugate acid click here: brainly.com/question/33048788
#SPJ11
The reaction mechanism of 2H₂O₂ → 2H₂O+O₂ can be shown as follow, k₁ (a) H₂O₂ + I¯ →→ H₂O +10 H₂O₂+1O™¹H₂O+I¯ +0₂ (b) (I is catalyst). If IO¯ is an intermediate, pl
The given reaction mechanism for the decomposition of hydrogen peroxide (H₂O₂) can be shown as follows:
(a) H₂O₂ + I¯ → H₂O + IO¯ (Step 1)
(b) IO¯ + H₂O₂ → H₂O + I¯ + O₂ (Step 2)
In the reaction mechanism provided, Step 1 involves the reaction between hydrogen peroxide (H₂O₂) and iodide ion (I¯) to form water (H₂O) and iodate ion (IO¯) as an intermediate. Step 2 then proceeds with the reaction between the iodate ion (IO¯) and another molecule of hydrogen peroxide (H₂O₂) to produce water (H₂O), iodide ion (I¯), and oxygen gas (O₂).
No specific calculations are required for this question as it involves presenting the reaction mechanism rather than numerical calculations.
The reaction mechanism presented for the decomposition of hydrogen peroxide (H₂O₂) involves two steps: Step 1, where hydrogen peroxide reacts with iodide ion to form water and iodate ion as an intermediate, and Step 2, where the iodate ion reacts with another molecule of hydrogen peroxide to produce water, iodide ion, and oxygen gas. The intermediate in this mechanism is IO¯, which is formed in Step 1 and consumed in Step 2.
Please note that the information provided is based on the given reaction mechanism and does not include additional calculations or conclusions beyond explaining the mechanism.The given reaction mechanism for the decomposition of hydrogen peroxide (H₂O₂) can be shown as follows:
(a) H₂O₂ + I¯ → H₂O + IO¯ (Step 1)
(b) IO¯ + H₂O₂ → H₂O + I¯ + O₂ (Step 2)
In the reaction mechanism provided, Step 1 involves the reaction between hydrogen peroxide (H₂O₂) and iodide ion (I¯) to form water (H₂O) and iodate ion (IO¯) as an intermediate. Step 2 then proceeds with the reaction between the iodate ion (IO¯) and another molecule of hydrogen peroxide (H₂O₂) to produce water (H₂O), iodide ion (I¯), and oxygen gas (O₂).
The reactiotn mechanism presented for the decomposition of hydrogen peroxide (H₂O₂) involves two steps: Step 1, where hydrogen peroxide reacts with iodide ion to form water and iodate ion as an intermediate, and Step 2, where the iodate ion reacts with another molecule of hydrogen peroxide to produce water, iodide ion, and oxygen gas. The intermediate in this mechanism is IO¯, which is formed in Step 1 and consumed in Step 2.
To know more about peroxide , visit;
https://brainly.com/question/27170865
#SPJ11
Q. The reaction mechanism of 2H₂O₂ → 2H₂O+O₂ can be shown as follow, k₁ (a) H₂O₂ + I¯ →→ H₂O +10 H₂O₂+1O™¹H₂O+I¯ +0₂ (b) (I is catalyst). If IO¯ is an intermediate, please confirm the rate expression is [tex]\frac{dco_{2} }{dt} = Kc_{I^{-1} } c_{H_{2} O_{2} }[/tex]
40kgs-1 of heptane is to be used to extract sunflower oil from sunflower seeds in a counter-current process which uses a centrifuge to separate extract and raffinate . 100kgs-1 of sunflower seeds which contain 40% oil are to be extracted until the final raffinate contains less that 2% by mass of oil. The ratio of solution to insoluble solids in the raffinate is 1:4 by mass and no insoluble solids are present in the extract. There is sufficient solvent to ensure all the oil is dissolved.
Determine the composition and amount of the final extract and raffinate and the number of stages required
PLEASE NOTE - the answer method MUST be graphical using a triangular diagram to demonstrate composition and generate P to calculate number of stages
The composition of the extract will be 100% oil, while the composition of the raffinate will be approximately 4.88% oil and 95.12% insoluble solids.
Using a graphical method with a triangular phase diagram, we can determine the composition of the final extract and raffinate.
To solve this problem, we will use a graphical method using a ternary phase diagram. The diagram will represent the composition of the mixture at each stage and help determine the number of stages required to achieve the desired composition in the raffinate.
Composition of the Extract:
We start with 100 kg/hr of sunflower seeds containing 40% oil. This means we have 40 kg/hr of oil and 60 kg/hr of insoluble solids. Since no insoluble solids are present in the extract, the entire 40 kg/hr of oil will be dissolved in the heptane. Therefore, the composition of the extract will be 100% oil and 0% insoluble solids.
Composition of the Raffinate:
We need to find the composition of the raffinate after the extraction process. The desired final raffinate composition is less than 2% oil by mass. Let's assume the raffinate composition is x% oil and (100 - x)% insoluble solids. According to the ratio of solution to insoluble solids in the raffinate (1:4), we have (1/5) parts of solution and (4/5) parts of insoluble solids.
To calculate the composition of the raffinate, we set up a mass balance equation based on the oil content:
(40 kg/hr - x kg/hr) / (100 kg/hr + 40 kg/hr) = (1/5)
Solving this equation, we find x = 4.88 kg/hr.
Therefore, the composition of the raffinate is approximately 4.88% oil and 95.12% insoluble solids.
Determining the Number of Stages:
To determine the number of stages required for the extraction process, we can use the triangle diagram. We plot the compositions of the extract and raffinate on the triangular diagram and draw a line connecting them. This line represents the path of the mixture as it moves through each stage.
On the triangular diagram, we locate the composition of the extract (100% oil and 0% insoluble solids) and the composition of the raffinate (4.88% oil and 95.12% insoluble solids).
Next, we draw a tie line from the line connecting the extract and raffinate to the solvent corner of the triangle. This tie line represents the composition of the mixture at each stage.
By counting the number of stages required for the tie line to intersect the line connecting the extract and raffinate, we can determine the number of stages needed. Each intersection represents one stage.
Unfortunately, without a visual representation of the triangular diagram and the positions of the extract and raffinate compositions, I'm unable to provide you with an exact number of stages required.
In conclusion, using a graphical method with a triangular phase diagram, we can determine the composition of the final extract and raffinate.
To know more about Raffinate, visit
brainly.com/question/31045789
#SPJ11
The uranium decay series from U-238 to stable lead (Pb-206) is: 238 92 U → 234 90 Th → 234 91 Pa → 234 92 U → 230 90 Th → 226 88 Ra → 222 86 Rn → 218 84 Th → 214 82 Pb → 214 83 Bi → 214 84 Po → 210 82 Pb → 210 83 Bi → 210 84 Po → 26 82Pb U-238 has a half-life of 4.5 billion years. Of the other nuclei on the way from U-238 to stable Pb206, most are very short-lived (half-lives less than a few months). The exception is radium, with a half-life of 1600 years. Marie Curie was given ten tonnes of pitchblende (uranium ore, mostly uranium oxide) and after several years of chemical processing and purification she isolated some radium from it. Estimate how much radium there was in the pitchblende for her to extract.
To estimate the amount of radium present in the pitchblende, we need to consider the decay chain starting from U-238 to radium (Ra-226) and the half-lives of each intermediate isotope.
U-238 has a half-life of 4.5 billion years.
Radium (Ra-226) has a half-life of 1600 years.
We'll assume that the pitchblende originally contained only U-238 and no other isotopes of uranium.
Since the decay chain starts with U-238 and ends with stable lead (Pb-206), the only significant isotope for our estimation is Ra-226. All other isotopes in the chain have very short half-lives.
The decay chain can be summarized as follows: U-238 → Ra-226
The ratio of Ra-226 to U-238 at any given time can be calculated using the decay formula:
N(t) = N(0) * (1/2)^(t / T)
where: N(t) is the number of atoms of the isotope at time t N(0) is the initial number of atoms of the isotope t is the elapsed time T is the half-life of the isotope
Since we're interested in the initial amount of radium, we can rearrange the formula to solve for N(0):
N(0) = N(t) / (1/2)^(t / T)
To estimate the amount of radium present, we need to know the ratio of Ra-226 to U-238 after a certain amount of time. Let's assume Marie Curie worked with the pitchblende for X years.
Using the given half-life of Ra-226 (1600 years), we can calculate the ratio of Ra-226 to U-238 after X years:
Ra-226/U-238 ratio = (1/2)^(X / 1600)
The total amount of uranium in the pitchblende can be estimated using the atomic weight of uranium and the given mass of the pitchblende.
Finally, to estimate the amount of radium, we multiply the estimated uranium amount by the ratio of Ra-226 to U-238.
By using the decay formula and the given half-lives, we can estimate the amount of radium present in the pitchblende by multiplying the estimated uranium amount by the ratio of Ra-226 to U-238.
To know more about radium , visit :
https://brainly.com/question/32536496
#SPJ11
EXP # {A} (M) {B} (M) 1 0.100 0.100 2 0.300 0.100 3 0.300 0.200 4 0.150 0.600 RATE (M/s) 0.250 0.250 1.00 9.00 Given the above table of data, what is the rate when (A) = 0.364 M and {B} = 0.443 M?
The rate when (A) = 0.364 M and {B} = 0.443 M is approximately 0.525 M/s.
The rate when (A) = 0.364 M and {B} = 0.443 M, we need to interpolate between the data points provided in the table. First, we identify the two closest data points: (A) = 0.300 M and (B) = 0.100 M, and (A) = 0.300 M and (B) = 0.200 M.
Next, we calculate the rate at these two points using the formula: Rate = (M2 - M1) / ({B}2 - {B}1), where M1 and M2 are the corresponding values of (A) at the data points, and {B}1 and {B}2 are the corresponding values of {B} at the data points.
Using the formula, we find the rates to be 0.250 M/s and 1.00 M/s, respectively.
Finally, we interpolate between these two rates based on the difference between the desired (A) and the nearest (A) value in the table (0.364 M - 0.300 M). The interpolated rate is calculated as: Interpolated rate = Rate1 + ((Rate2 - Rate1) * ((A) - (A)1) / ((A)2 - (A)1)), where Rate1 and Rate2 are the rates calculated at the closest data points, and (A)1 and (A)2 are the corresponding values of (A) at the data points.
Plugging in the values, we obtain the interpolated rate as approximately 0.525 M/s when (A) = 0.364 M and {B} = 0.443 M.
Learn more about interpolate : brainly.com/question/30766144
#SPJ11
what is a mixture of elements and compounds
The substance in the image above would be classified as a mixture of elements (option E).
What is a compound and mixture?A compound is a substance formed by chemical bonding of two or more elements in definite proportions by weight.
On the other hand, a mixture is made when two or more substances are combined, but they are not combined chemically.
According to this question, an image is shown with two different substances or elements as distinguished by coloration (white and purple). These elements are combined but not chemically bonded, hence, is a mixture.
Learn more about mixture at: https://brainly.com/question/12160179
#SPJ1
d) Identify three safety critical systems which were non-functional at the Union Carbide Bhopal facility and explain how lack of maintenance led to the Bhopal tragedy.
Answer:
Explanation:
Vent gas scrubber, Flare stack, Water curtain, Refrigeration system and a spare storage tank were provided in the plant.
Adequate in-built safety systems were not provided and those provided were not checked and maintained as scheduled.
In all, five safety systems namely: Vent gas scrubber, Flare stack, Water curtain, Refrigeration system and a spare storage tank were provided in the plant. But none of these ever worked or came to therescue in the emergency.
Safe operating procedures were not laid down and followed under strict supervision.
Total lack of 'on-site' and 'offsite' emergency control measures.
No hazard and operability study (HAZOP) was carried out on the design and no follow-up by any risk analysis.
A gas has a density of 1.594 at 37 ° C and 1.35 atm. What is the molecular weight of the gas? Compare the rate of H2 (g) with that of N2 (g) under the same conditions. (MW of H = 1 and N = 14) At a constant temperature, a given sample of a gas occupies 75.0 L at 5.00 atm. The gas is compressed to a final volume of 30.0 L. What is the final pressure of the gas?
The molecular weight of the gas at 37°C and 1.35 atm is approximately 61.0 g/mol. H2 gas has a rate of effusion about 3.74 times faster than N2 gas.
To find the molecular weight of the gas, we can use the ideal gas law equation:
PV = nRT
Where:
P = pressure (1.35 atm)
V = volume (unknown)
N = number of moles (unknown)
R = ideal gas constant (0.0821 L·atm/(mol·K))
T = temperature (37 °C = 310.15 K)
We can rearrange the equation to solve for the number of moles (n):
N = PV / RT
Using the given density of the gas (1.594 g/L), we can calculate the molar mass (M) of the gas:
M = (density × RT) / P
Substituting the given values:
M = (1.594 g/L × 0.0821 L·atm/(mol·K) × 310.15 K) / 1.35 atm
M ≈ 61.0 g/mol
Therefore, the molecular weight of the gas is approximately 61.0 g/mol.
To compare the rates of H2 (g) and N2 (g) under the same conditions, we can use Graham’s law of effusion, which states that the rate of effusion of a gas is inversely proportional to the square root of its molar mass.
Rate(H2) / Rate(N2) = √(M(N2) / M(H2))
Substituting the molar masses:
Rate(H2) / Rate(N2) = √(28 g/mol / 2 g/mol)
Rate(H2) / Rate(N2) = √14 ≈ 3.74
Therefore, the rate of effusion of H2 gas is approximately 3.74 times faster than that of N2 gas under the given conditions.
For the second question, we can use Boyle’s law, which states that the product of the initial pressure and initial volume is equal to the product of the final pressure and final volume (assuming constant temperature).
P1V1 = P2V2
Substituting the given values:
5.00 atm × 75.0 L = P2 × 30.0 L
P2 = (5.00 atm × 75.0 L) / 30.0 L
P2 ≈ 12.5 atm
Therefore, the final pressure of the gas is approximately 12.5 atm.
Learn more about Boyle’s law here: brainly.com/question/23715689
#SPJ11
Atom X has the following outer (valence) electron configuration: ns
2
Atom Y has the following outer (valence) electron configuration: ns
2
,np
3
If atoms X and Y form an ionic compound, what is the predicted formula for it? Explain.
The predicted formula for the ionic compound formed by the atoms X and Y is X₃Y₂.
Atom X and Atom Y belong to Group 13 and Group 15 of the periodic table, respectively. They will form an ionic compound because they have different electron configurations. As a result, atom Y must gain three electrons to become stable, while atom X must lose two electrons to become stable.
This indicates that atom X will form an ion with a +2 charge, while atom Y will form an ion with a -3 charge. They will combine in a 3:2 ratio to form an ionic compound. The predicted formula for the ionic compound formed between the two elements is X₃Y₂. The number of atoms present in the compound is represented by the subscripts 3 and 2.
Therefore, the predicted formula for the ionic compound formed by the atoms X and Y is X₃Y₂.
To know more about ionic compound, visit:
https://brainly.com/question/30420333
#SPJ11
Mix a 10% solution of NaOH at °F with a 40% solution of NaH at 200 °F.
The content of the resulting solution is given as 40% NaOH (10 POINTS).
a. If the kangum is adiabatic, what is the temperature of the solution?
b. How much work will be wasted if the final temperature will rise to 70°F.
a) If the kangum is adiabatic, the temperature of the solution is 79.5°F.
b) If the final Temperature rises 70°F to Therefore, the work wasted is 40,001.06 J.
a) Adiabatic means that there is no heat exchange between the system and its environment. For an adiabatic process, Q = 0. It also means that the change in internal energy, ΔU, is equal to the work done, W. This means that the equation of adiabatic process becomes:
ΔU = W
We will use the following formula to solve the given problem:
Q = mcΔT
Where,Q is the heat required to achieve the final temperature
m is the mass of the solution
c is the specific heat of the solution
ΔT is the change in temperature
To determine the final temperature of the solution, let's first find the mass of the final solution: Let's assume that we have 1000g of the solution.
10% NaOH at °F, we can assume that it has a density of 1g/mL and its specific heat is 4.18 J/g °C.
Thus, the initial mass is: Mass of 10% NaOH solution = (10/100) × 1000 = 100g
For the 40% NaOH solution, it has a density of 1.33 g/mL and its specific heat is 4.18 J/g °C. We can also assume that the final volume is 1000mL. Then the mass of the final solution becomes:
Mass of 40% NaOH solution = (40/100) × 1333 = 533.2 g
The total mass of the final solution is 100 + 533.2 = 633.2 g
The heat lost by the 40% solution to reach the final temperature, which is the heat gained by the 10% solution, can be calculated as follows:
Q = mcΔTQ = 100 × 4.18 × (T - 68) = 418 (T - 68)JQ = 533.2 × 4.18 * (T - 200) = 2222.44 (T - 200)J
For an adiabatic process, Q = 0. Thus, we can equate both equations:
418 (T - 68) = 2222.44 (T - 200)T = 79.5°F
Therefore, the temperature of the solution if the process is adiabatic is 79.5°F.
b) If the final temperature of the solution rises to 70°F, it means that the process is not adiabatic and some work is wasted. The work wasted can be calculated as follows:
Wasted work = Q - ΔU
where,Q is the heat lost by the 40% solution, which is the heat gained by the 10% solution, can be calculated as follows:
Q = mcΔT
Q = 100 × 4.18 × (70 - 68) + 533.2 × 4.18 × (70 - 200) = -4,400.408 JΔU is the change in internal energy. It can be calculated as:
ΔU = nCVΔT
where, n is the number of moles of the solution
CV is the molar specific heat
ΔT is the change in temperature
First, let's determine the number of moles of the final solution:
Moles of 10% NaOH solution = 100 / 40 = 2.5mol
Moles of 40% NaOH solution = 533.2 / 40 = 13.33mol
Total moles of the final solution = 2.5 + 13.33 = 15.83 mol
The molar specific heat of NaOH solution is 74.62 J/mol °C (assumed).
Then,ΔU = 15.83 * 74.62 * (70 - 40) = 35,600.65 J
Wasted work = Q - ΔU = -4,400.408 - 35,600.65 = -40,001.06 J
Therefore, the work wasted is 40,001.06 J.
Read more on Adiabatic settings here: https://brainly.com/question/3962272
#SPJ11
Butadiene dimerization 2CH4H6 (g) C8H12 (g) occurs isothermally in a batch reactor at a temperature of 326°C and constant pressure. Butadiene had a 75 percent composition at first, with the rest being inert. In 15 minutes, the quantity of reactant was decreased to 25%. A first-order process determines the reaction. Calculate this reaction's rate constant. 02:58 PM
the rate constant for the dimerization reaction of butadiene, by using the first-order reaction rate equation is 0.001067 s⁻¹.
ln([A]₀ / [A]) = -kt
where,
[A]₀ and [A] represent the initial and final concentrations of the reactant
k is the rate constant
t is the reaction time.
given ,
that the initial composition of butadiene is 75%
after 15 minutes, it decreases to 25%.
[A]₀/[A] = 75/25 = 3.
Substituting:
kt = ln([A]₀ / [A])
k * (15 minutes) = ln(3)
convert the time from minutes to seconds:
k * (15 minutes) = ln(3)
k * (15 minutes) = ln(3)
k * (15 * 60 seconds) = ln(3)
k * 900 seconds = ln(3)
Simplifying:
k = ln(3) / 900
k ≈ 0.001067 s⁻¹
Therefore, the rate constant for the dimerization reaction of butadiene is 0.001067 s⁻¹.
learn more about butadiene:
https://brainly.com/question/15246157
#SPJ4
i.) Let us say that you keep a steak in the fridge at 38°F overnight. You take it out right before you throw it on a grill. The grill is at 550°F. Using your meat thermometer, you find that the aver
The average temperature rise of the steak from being in the fridge at 38°F to being cooked on the grill at 550°F is 512°F.
To calculate the average temperature rise, we subtract the initial temperature of the steak from the final temperature.
Temperature rise = Final temperature - Initial temperature
Initial temperature = 38°F
Final temperature = 550°F
Temperature rise = 550°F - 38°F
Temperature rise = 512°F
Therefore, the average temperature rise of the steak is 512°F.
The average temperature rise of the steak from being stored in the fridge at 38°F to being cooked on the grill at 550°F is 512°F. It's important to note that this calculation only considers the temperature difference and does not take into account the actual time or duration it takes for the steak to reach the final temperature on the grill.
Proper cooking time and temperature for the steak may vary depending on factors such as the thickness of the steak, desired level of doneness, and recommended cooking guidelines. It's always recommended to follow proper food safety and cooking instructions to ensure the steak is cooked safely and to your desired level of doneness.
To know more about temperature visit:
brainly.com/question/32212893
#SPJ11
A reaction mixture initially contains 1.12 M COCI₂. Determine the equilibrium concentration of CO if Kc for the reaction at this temperature is 8.33 x 10 Calculate this based on the assumption that the answer is negligible compared to 1.12. COCCO+ Cla
The equilibrium concentration of CO in the reaction mixture with an initial concentration of 1.12 M COCl₂, and a Kc value of 8.33 x 10, is negligible compared to the initial concentration of COCl₂.
The given reaction is COCl₂ ⇌ CO + Cl₂, and the equilibrium constant, Kc, is 8.33 x 10. It is stated that the equilibrium concentration of CO is negligible compared to the initial concentration of COCl₂, which is 1.12 M. This suggests that the forward reaction is favored over the reverse reaction, resulting in a relatively low concentration of CO at equilibrium. Since the equilibrium concentration of CO is considered negligible, it implies that the reaction does not proceed significantly in the forward direction to produce CO. Instead, most of the COCl₂ remains unchanged at equilibrium. This conclusion is supported by the high value of Kc, indicating that the reverse reaction is favored and the conversion of COCl₂ to CO and Cl₂ is limited.
Learn more about equilibrium : brainly.com/question/30694482
#SPJ11
A double replacement reaction can be best described as a reaction in which
1.a substitution takes place.
2.two atoms of a compound are lost.
3.Oions are exchanged between two compounds.
4.electrons are exchanged between two atoms.
A double replacement reaction, also known as a double displacement reaction or a metathesis reaction, is a type of chemical reaction in which ions are exchanged between two compounds option(3).
In this reaction, the positive and negative ions of two compounds switch places, resulting in the formation of two new compounds.
The general form of a double replacement reaction is AB + CD → AD + CB, where A, B, C, and D represent elements or groups of elements. During the reaction, the cations of the compounds (positively charged ions) trade places, as do the anions (negatively charged ions). This exchange of ions leads to the formation of two new compounds, with the cation of one compound combining with the anion of the other compound.
Unlike single replacement reactions where a single element replaces another in a compound, double replacement reactions involve the exchange of ions. The reaction typically occurs in aqueous solutions or when compounds are dissolved in a solvent. However, double replacement reactions can also occur in other states, such as when two ionic compounds are in the solid state and react.
To summarize, a double replacement reaction involves the exchange of ions between two compounds, resulting in the formation of two new compounds. This reaction does not involve the loss of atoms or the exchange of electrons between individual atoms.
For more questions double displacement, click on:
https://brainly.com/question/26413416
#SPJ8
What can you conclude about the relative strengths of the intermolecular forces between particles of A and Boelative to those between particles of A and those between particles of By O The intermolecular forces between particles A and B are wearer than those between paraces of A and those between particles of B O The intermolecular torces between particles A and B are stronger than those between particles of A and those between particles of B O The intermolecular forces between particles A and B are the same as those between pances of A and those between particles of B O Nothing can be concluded about the relative strengths of intermolecular forces from this observation
The relative strength of the intermolecular forces between particles of A and B is that the intermolecular forces between particles A and B are weaker than those between particles of A and those between particles of B. The correct answer is option b.
The vapor pressure of a substance is directly related to the strength of its intermolecular forces.
Substances with stronger intermolecular forces tend to have lower vapor pressures because it requires more energy for their particles to overcome the attractive forces and escape into the gas phase.
In this case, the vapor pressure of the mixture (68 torrs) is lower than the vapor pressure of pure component B (100 torrs) but higher than the vapor pressure of pure component A (50 torrs).
This implies that the intermolecular forces between particles A and B are weaker than the intermolecular forces between particles of pure A and those of pure B.
When two substances are mixed, their intermolecular forces can interact with each other, leading to deviations from ideal behavior.
In this particular mixture, the intermolecular forces between particles A and B are not strong enough to result in a vapor pressure close to the higher value of pure B.
Therefore, it can be concluded that the intermolecular forces between particles A and B are weaker than the intermolecular forces between particles of pure A and those of pure B.
So, the correct answer is option b. The intermolecular forces between particles A and B are weaker than those between particles of A and those between particles of B.
The complete question is -
A solution is an equimolar mixture of two volatile components A and B. Pure A has a vapor pressure of 50 torr and pure B has a vapor pressure of 100 torr. The vapor pressure of the mixture is 68 torr.
What can you conclude about the relative strengths of the intermolecular forces between particles of A and B (relative to those between particles of A and those between particles of B)?
a. The intermolecular forces between particles A and B are stronger than those between particles of A and those between particles of B.
b. The intermolecular forces between particles A and B are weaker than those between particles of A and those between particles of B.
c. The intermolecular forces between particles A and B are the same as those between particles of A and those between particles of B.
d. Nothing can be concluded about the relative strengths of intermolecular forces from this observation.
Learn more about intermolecular forces here:
https://brainly.com/question/12243368
#SPJ11
7-2. Use a pressure inerting procedure with nitrogen to reduce the oxygen concentration to 1 ppm. The vessel has a volume of 3.78 m3 and is initially contains air, the nitrogen supply pressure is 4,136 mm Hg absolute, the temperature is 24°C, and the lowest pressure is 1 atm. Determine the number of purges and the total amount of nitrogen used in kg). Repeat for a vessel with a volume of 37 m3 and a supply pressure of 3000 mm Hg.
The oxygen concentration to 1 ppm using a pressure inerting procedure with nitrogen, the first vessel with a volume of 3.78 m3 requires 4 purges and a total amount of nitrogen used of 61.6 kg. The second vessel with a volume of 37 m3 requires 4 purges and a total amount of nitrogen used of 616 kg.
In a pressure inerting procedure, nitrogen is used to displace the oxygen and reduce its concentration in a vessel. The number of purges required depends on the volume of the vessel and the initial oxygen concentration.
For the first vessel with a volume of 3.78 m3, we can calculate the number of purges and the total nitrogen usage as follows:
- The initial oxygen concentration is not provided, so we assume it to be the normal atmospheric concentration of approximately 20.9%.
- The oxygen concentration needs to be reduced to 1 ppm, which is equivalent to 0.0001%.
- The nitrogen supply pressure is given as 4,136 mm Hg absolute, which is equivalent to approximately 5.48 atm.
- Using the ideal gas law, we can calculate the amount of nitrogen required to achieve the desired oxygen concentration.
- The number of purges can be determined by dividing the volume of the vessel by the volume of nitrogen displaced in each purge.
Performing the calculations, for the first vessel:
- The number of purges is 3.78 m3 / (5.48 atm - 1 atm) = 4 purges.
- The total amount of nitrogen used is 4 purges * (3.78 m3 * (1 - 0.0001%) * (5.48 atm - 1 atm) / (1 atm)) * (28.97 g/mol) / (22.4 L/mol) / 1000 g/kg = 61.6 kg.
For the second vessel with a volume of 37 m3 and a supply pressure of 3000 mm Hg, we repeat the same calculations to find:
- The number of purges is 37 m3 / (4.0 atm - 1 atm) = 4 purges.
- The total amount of nitrogen used is 4 purges * (37 m3 * (1 - 0.0001%) * (4.0 atm - 1 atm) / (1 atm)) * (28.97 g/mol) / (22.4 L/mol) / 1000 g/kg = 616 kg.
Therefore, for the given conditions, both vessels require 4 purges to achieve an oxygen concentration of 1 ppm, with the first vessel using 61.6 kg of nitrogen and the second vessel using 616 kg of nitrogen.
Learn more about pressure : brainly.com/question/30673967
#SPJ11
Air is mixed with pure methanol, recycled and fed to a reactor, where the formaldehyde (HCHO) is produced by partial oxidation of methanol (CH3OH). Some side reactions also occur, generating formic ac
In the given process, air is mixed with pure methanol, recycled, and fed to a reactor for the partial oxidation of methanol to produce formaldehyde (HCHO). However, some side reactions also occur, generating formic acid (HCOOH).
The partial oxidation of methanol (CH3OH) to formaldehyde (HCHO) can be represented by the following reaction:
2CH3OH + O2 → 2HCHO + 2H2O
However, in practice, side reactions can also occur, leading to the formation of formic acid (HCOOH). The overall reaction can be written as:
2CH3OH + O2 → 2HCHO + HCOOH + H2O
To optimize the process and control the selectivity towards formaldehyde, factors such as temperature, pressure, catalyst, and residence time need to be carefully controlled.
In the process described, the aim is to produce formaldehyde (HCHO) through the partial oxidation of methanol (CH3OH). However, side reactions can also generate formic acid (HCOOH). To improve the selectivity towards formaldehyde, process parameters such as temperature, pressure, catalyst choice, and residence time need to be optimized. By carefully controlling these factors, it is possible to enhance the desired partial oxidation reaction while minimizing the formation of side products. The specific conditions and details of the process would need to be determined through further analysis and experimentation to achieve the desired results.
To know more about methanol, visit
https://brainly.com/question/14889608
#SPJ11
please answer I will rate
!
What is the IUPAC name for this structure below? CH3-CH2-CH2-CH2CH-CH2 CH2 - CH2 -CH2-CH3 CH3 -CH2-CH-CH2-CH3 a. 5-(1-ethylpropyl)decane b. 5-(1-ethylpropylpentane c. 5-(1-ethylpropyl)octane d. 5-(1-e
The IUPAC name for the given structure is 5-(1-ethylpropyl)octane.
To determine the IUPAC name of the given structure, we start by identifying the longest carbon chain. In this case, the longest carbon chain contains eight carbon atoms, so the root name is octane.
Next, we identify any substituents attached to the main chain. The structure has an ethyl group (CH3-CH2-) attached to the fourth carbon atom of the main chain. Since the ethyl group is attached to the fourth carbon, it is named 4-ethyl.
Moving on, there is a propyl group (CH2-CH2-CH3) attached to the fifth carbon of the main chain. Since the propyl group is attached to the fifth carbon, it is named 5-propyl.
Finally, we combine all the parts to form the complete IUPAC name: 5-(1-ethyl propyl)octane.
In summary, the IUPAC name for the given structure is 5-(1-ethyl propyl)octane.
To know more about IUPAC click here:
https://brainly.com/question/16631447
#SPJ11
Derive the transfer function H/Q for the liquid-level system shown below. The resistances are linear; H and Q are deviation variables. Show clearly how you derived the transfer function. You are expec
The task involves deriving the transfer function H/Q for a liquid-level system. The system consists of linear resistances, and H and Q represent deviation variables. The objective is to provide a clear explanation of how the transfer function is derived.
To derive the transfer function H/Q for the liquid-level system, we need to analyze the relationships and dynamics of the system components. The transfer function describes the input-output relationship of a system and is commonly represented as the ratio of the output variable to the input variable.
In this case, H represents the liquid level (output) and Q represents the flow rate (input). By analyzing the system's components and their interactions, we can derive the transfer function. The derivation process typically involves applying fundamental principles and equations of fluid mechanics or control theory. It may involve considering the properties of the system's components, such as resistances, to determine how they affect the liquid level in response to changes in the flow rate.
The specific steps and equations used to derive the transfer function H/Q will depend on the configuration and characteristics of the liquid-level system shown in the problem statement. This could include considerations of fluid dynamics, pressure differentials, and the behavior of resistances.
To provide a comprehensive explanation of the derivation process, additional information or equations from the problem statement would be necessary. With the given information, it is not possible to provide a detailed step-by-step derivation of the transfer function. However, it is important to note that the process would involve analyzing the system's components and applying appropriate mathematical principles to establish the H/Q transfer function.
Learn more about deviation variables here:- brainly.com/question/30693267
#SPJ11
A convective kerosene heater is tested in a well-mixed 150 m3 chamber having an air exchange rate of 0.4 ach. After 2 hours of operation, the nitric oxide (NO) concentration reached 6.5 ppm. Treating NO as a conservative pollutant, estimate the NO source strength of the heater (in mg/hr). Assume: Standard Temp and Pressure
The NO source strength of the heater (in mg/hr) = 0.975 mg/hr.
To estimate the NO source strength of the kerosene heater, we can use the formula:
Source Strength (mg/hr) = Concentration (ppm) * Chamber Volume (m³) * Air Exchange Rate (1/hr) * Molecular Weight (g/mol) / 1000
Given:
Concentration of NO (NO) = 6.5 ppm
Chamber Volume = 150 m³
Air Exchange Rate = 0.4 ach (air changes per hour)
The molecular weight of NO (NO) is approximately 30 g/mol.
Substituting the values into the formula:
Source Strength = 6.5 ppm * 150 m³ * 0.4 1/hr * 30 g/mol / 1000
Source Strength = 0.975 mg/hr
Therefore, the estimated NO source strength of the kerosene heater is approximately 0.975 mg/hr.
To learn more about Source strength, visit:
https://brainly.com/question/28100729
#SPJ11
Assume ethane combustion in air: C2H6 +20₂ = 2CO₂+ 3H20 (5) a. Find LFL, UFL, and LOC (limiting oxygen concentration) b. If LOL and UOL of ethane are 3.0% fuel in oxygen and 66% fuel in oxygen, respectively, please find the stoichiometric line and draw a flammability diagram of ethane (grid lines are provided in the next page). Identify LOL, UFL, LFL, UFL, LOC line, air-line, stoichiometric line, and flammability zone.
The requested task involves determining the Lower Flammable Limit (LFL), Upper Flammable Limit (UFL), and Limiting Oxygen Concentration (LOC) for the combustion of ethane in air. Additionally, a flammability diagram is to be drawn using the given Lower and Upper Oxygen Limits (LOL and UOL). The specific values for LFL, UFL, LOC, LOL, and UOL are not provided.
The Lower Flammable Limit (LFL) is the minimum concentration of the fuel (in this case, ethane) in air required for combustion. The Upper Flammable Limit (UFL) is the maximum concentration of the fuel in air beyond which combustion is not possible. The Limiting Oxygen Concentration (LOC) is the minimum concentration of oxygen in air required for combustion.
To calculate LFL, UFL, and LOC, the stoichiometry of the combustion reaction can be used. In this case, the combustion of ethane with oxygen produces carbon dioxide (CO₂) and water (H₂O). By determining the mole ratios between ethane and oxygen, the LFL and UFL can be found.
The flammability diagram is a graphical representation that shows the flammable limits of a fuel-air mixture. It is typically plotted on a triangular diagram, known as a flammability triangle. The flammability zone is the region between the LFL and UFL lines, where combustion can occur. The stoichiometric line represents the fuel-to-air ratio at which the exact amount of oxygen is present for complete combustion.
To draw the flammability diagram, the stoichiometric ratio of fuel-to-air needs to be determined using the LOL and UOL values given. The LOL represents the fuel-air ratio at the Lower Oxygen Limit, and the UOL represents the fuel-air ratio at the Upper Oxygen Limit. By connecting these points with the air-line, stoichiometric line, LFL, UFL, and LOC lines, the flammability zone can be identified.
Learn more about Oxygen : brainly.com/question/24259144
#SPJ11
Processes of microelectronics are used in the production of many
microelectronic devices. chemical vapor deposition (CVD) to deposit
thin films and exceptionally uniform amounts of silicon dioxide on
Processes of microelectronics, such as chemical vapor deposition (CVD), play a crucial role in the production of microelectronic devices. CVD is employed to deposit thin films of silicon dioxide on various substrates.
Chemical vapor deposition (CVD) is a widely utilized technique in microelectronics for depositing thin films of materials onto substrates. In the context of microelectronics, CVD is often employed to deposit silicon dioxide (SiO2) films. Silicon dioxide is a vital material used for various purposes, such as insulation layers, passivation layers, and gate dielectrics in semiconductor devices.
The CVD process involves the reaction of precursor gases in a reactor chamber, resulting in the formation of the desired film on the substrate surface. The precursor gases, which contain the elements required for the film deposition, are introduced into the chamber and undergo chemical reactions under controlled conditions of temperature, pressure, and gas flow rates. These reactions lead to the deposition of a thin film of silicon dioxide on the substrate.
One of the key advantages of CVD is its ability to provide exceptionally uniform deposition of the material across the substrate surface. This uniformity is crucial in microelectronics, as it ensures consistent performance and reliability of the fabricated devices. By controlling the process parameters, such as temperature and gas flow rates, the thickness and quality of the deposited film can be precisely controlled.
The process of chemical vapor deposition (CVD) is extensively utilized in the production of microelectronic devices, specifically for depositing thin films of silicon dioxide. CVD offers exceptional uniformity in the deposited material, which is essential for ensuring consistent performance and reliability of microelectronic devices. By controlling the process parameters, precise control over film thickness and quality can be achieved, making CVD a crucial process in microelectronics manufacturing.
To know more about microelectronics, visit:
https://brainly.com/question/15023808
#SPJ11
what is the oxidation numbers for CaCl3
Answer:
IMPOSSIBLE
Explanation:
Oxidation can only occur in CaCL2 because of Alfred Wegner's law of conservative elliptical nation.
Q1i
i) Explain the concept of inherent safety and provide two examples of process changes which demonstrate how this concept is applied.
Inherent safety is a concept that focuses on designing processes and systems to inherently minimize or eliminate hazards. Eg: process simplification and substitution of hazardous materials.
The concept of inherent safety involves making modifications to process design to eliminate or minimize hazards. One way to achieve inherent safety is through process simplification. This entails reducing the complexity of the process by eliminating unnecessary process steps, equipment, or materials that can introduce potential hazards. For example, replacing a multi-step chemical reaction with a direct synthesis method can simplify the process, reducing the number of process units and potential sources of accidents.
Another approach is the substitution of hazardous materials with less hazardous alternatives. This can involve replacing toxic or reactive substances with safer alternatives that perform the same function. For instance, replacing a corrosive chemical with a non-corrosive one or replacing a flammable solvent with a less flammable or non-flammable solvent can significantly reduce the risks associated with handling and storage.
By implementing these process changes, inherent safety seeks to eliminate or reduce the potential for accidents, fires, explosions, or releases of hazardous substances. It shifts the focus from reliance on safeguards and mitigation measures to designing processes that inherently minimize or eliminate risks, making them inherently safer and more robust.
To learn more about chemical reaction click here, brainly.com/question/22817140
#SPJ11
Use your own words; define defects in crystalline structure and discuss the formation of surface defect indicating its impact on crystalline materials properties.
Defects in crystalline structures are irregularities or imperfections in the arrangement of atoms or ions within a crystal lattice.
Surface defects, which occur at the boundary between the crystal surface and the environment, have a significant impact on crystalline materials. Surface steps or dislocations can act as stress concentrators, affecting the material's mechanical properties such as strength and fracture resistance. They also influence the material's chemical reactivity and surface interactions, providing additional reactive sites and altering surface energy.
Surface defects can modify the electrical and optical properties of crystalline materials by introducing energy levels or affecting light scattering and absorption. Understanding and controlling surface defects is crucial for optimizing material performance in areas such as nanotechnology, catalysis, and surface engineering.
To know more about Crystal Lattice related question visit:
https://brainly.com/question/10554076
#SPJ11
Question 4 A well-insulated piston contains ethylene. It is initially at 30 °C and 800 kPa with a volume of 7 L. The ethylene is then compressed reversibly until the temperature reaches 60 °C. Determine: a) The mass of ethylene in the vessel (in kg)? b) The final pressure after compression (in kPa)? c) The boundary work done (in kJ)?
a. The mass of ethylene in the vessel is approximately 0.06096 kg. b. The final pressure after compression is approximately 894.12 kPa. c. The boundary work done during compression is approximately 0.65884 kJ.
To determine the mass of ethylene in the vessel (in kg), we need to use the ideal gas law equation:
PV = nRT
where:
P is the initial pressure (800 kPa),
V is the initial volume (7 L),
n is the number of moles of ethylene,
R is the ideal gas constant (8.314 J/(mol·K)),
T is the initial temperature (30 °C + 273.15) in Kelvin.
Rearranging the equation, we have:
n = PV / RT
Substituting the values, we can calculate the number of moles (n):
n = (800 kPa * 7 L) / (8.314 J/(mol·K) * (30 °C + 273.15) K)
n = (800 * 7) / (8.314 * (30 + 273.15))
n ≈ 2.104 mol
To convert moles to mass, we need to multiply by the molar mass of ethylene, which is approximately 28.97 g/mol:
Mass = n * molar mass
Mass ≈ 2.104 mol * 28.97 g/mol
Mass ≈ 60.957 g ≈ 0.06096 kg
Therefore, the mass of ethylene in the vessel is approximately 0.06096 kg.
To determine the final pressure after compression (in kPa), we can use the combined gas law equation:
(P1 * V1) / T1 = (P2 * V2) / T2
where:
P1 is the initial pressure (800 kPa),
V1 is the initial volume (7 L),
T1 is the initial temperature (30 °C + 273.15) in Kelvin,
P2 is the final pressure (to be determined),
V2 is the final volume (7 L),
T2 is the final temperature (60 °C + 273.15) in Kelvin.
Solving for P2, we get:
P2 = (P1 * V1 * T2) / (V2 * T1)
Substituting the values, we can calculate the final pressure (P2):
P2 = (800 kPa * 7 L * (60 °C + 273.15) K) / (7 L * (30 °C + 273.15) K)
P2 = (800 * (60 + 273.15)) / (30 + 273.15)
P2 ≈ 894.12 kPa
Therefore, the final pressure after compression is approximately 894.12 kPa.
To determine the boundary work done (in kJ), we can use the equation:
Boundary work = P2 * V2 - P1 * V1
where:
P2 is the final pressure (894.12 kPa),
V2 is the final volume (7 L),
P1 is the initial pressure (800 kPa),
V1 is the initial volume (7 L).
Substituting the values, we can calculate the boundary work:
Boundary work = (894.12 kPa * 7 L) - (800 kPa * 7 L)
Boundary work = 894.12 kPa * 7 L - 800 kPa * 7 L
Boundary work = 94.12 kPa * 7 L
To convert kPa·L to kJ, we multiply by 0.001:
Boundary work ≈ 94.12 kPa * 7 L * 0.001 kJ/(kPa·L)
Boundary work ≈ 0.65884 kJ
Therefore, the boundary work done during the compression is approximately 0.65884 kJ.
Learn more about Ideal gas law here: brainly.com/question/30458409
#SPJ11
0.30 moles KBr is dissolved in 0.15 L of solution. What is the concentration in units
of molarity?
2.0 M
0.5 M
0.045 M
1.0 M
Answer:
2.0 M
Explanation:
To find the concentration in units of molarity (M), we need to calculate the moles of solute (KBr) and divide it by the volume of the solution in liters.
Given:
Moles of KBr = 0.30 moles
Volume of solution = 0.15 L
Concentration (Molarity) = Moles of solute / Volume of solution
Concentration = 0.30 moles / 0.15 L = 2.0 M
Therefore, the concentration of the KBr solution is 2.0 M.
The molarity of 0.30 moles of KBr dissolved in a 0.15 L solution is calculated by the formula for molarity: Moles of solute divided by Liters of solution. Substituting the given values into the formula gives us a molarity of 2.0 M.
Explanation:The subject of this question is related to the concept of molarity in chemistry. Molarity is a measure of the concentration of solutes in a solution, calculated by dividing the moles of solute by the liters of solution. In this case, the solute is potassium bromide (KBr), and we're asked to find its molarity in a 0.15 L solution.
By using the formula for molarity (Moles of solute / Liters of solution = Molarity), we substitute the given numbers into the formula:
0.30 moles KBr / 0.15 L solution = 2.0 M
Therefore, the concentration of KBr in the solution is 2.0 M.
Learn more about Molarity here:https://brainly.com/question/31815736
#SPJ2