Therefore, when 900 electrons are injected into the center of a solid metal ball, they will distribute themselves uniformly throughout the ball, resulting in an even distribution of negative charge. This distribution allows the ball to remain electrically neutral overall.
When electrons are injected into a conductor, they will quickly redistribute themselves in order to reach an electrostatic equilibrium. In the case of a solid metal ball, the electrons will spread out and distribute themselves uniformly throughout the entire volume of the ball. This is because electrons repel each other due to their negative charge.
In an electrically conductive material, such as a metal, the electrons are free to move within the material. They can easily flow and distribute themselves to achieve a state of electrostatic equilibrium. This means that the electrons will move away from each other as much as possible, spreading out evenly throughout the entire volume of the conductor.
Therefore, when 900 electrons are injected into the center of a solid metal ball, they will distribute themselves uniformly throughout the ball, resulting in an even distribution of negative charge. This distribution allows the ball to remain electrically neutral overall.
Learn more about electrostatic equilibrium here:
https://brainly.com/question/31947363
#SPJ11
Which of the following values of the phase constant o for a sinusoidally driven series RLC circuit, would be for a primarily capacitive load circuit? A) -150; B) +35.; C)*/3 rad; D) 1/6 rad. Answer
The primarily capacitive load circuit would have a phase constant of -150 degrees.
In a sinusoidally driven series RLC circuit, the phase constant determines the phase relationship between the current and voltage. A primarily capacitive load circuit is characterized by a leading current, meaning that the current waveform leads the voltage waveform. This implies that the phase constant should be negative.
Among the given options, the phase constant of -150 degrees corresponds to a primarily capacitive load circuit. A negative phase constant indicates that the current leads the voltage by 150 degrees.
This is characteristic of a circuit dominated by capacitive reactance.The other options (+35 degrees, */3 radians, and 1/6 radians) do not indicate a primarily capacitive load circuit.
Positive values for the phase constant would imply a lagging current, which is indicative of inductive loads. Therefore, the correct choice for a primarily capacitive load circuit is option A) -150 degrees.
Learn more about capacitive here ;
https://brainly.com/question/31871398
#SPJ11
Light is reflected from the surface of a lake (n = 1.37). What is the angle of incidence for which the reflected light is 100% polarized? A) 37.9° B) 53.9°C) 34.30 D) 56.6°E) 36.10 26. An ultra-fast pulse lasers emits pulses of 13 fs.
The angle of incidence for which the reflected light is 100% polarized is approximately 56.6° i.e., the correct option is D) 56.6°.
To determine the angle of incidence for which the reflected light is 100% polarized, we need to use the principle of Brewster's angle.
Brewster's angle states that when light is incident on a surface at a certain angle, the reflected light becomes completely polarized, meaning it oscillates in one plane.
The formula for Brewster's angle is given by:
tan(θ_B) = n2/n1
where θ_B is the Brewster's angle, n1 is the refractive index of the medium from which the light is coming (in this case, air), and n2 is the refractive index of the medium to which the light is incident (in this case, the lake).
Given that the refractive index of air is approximately 1 (since it's close to a vacuum) and the refractive index of the lake is 1.37, we can substitute these values into the equation:
tan(θ_B) = 1.37/1
Taking the arctan of both sides, we find:
θ_B = arctan(1.37/1)
Using a calculator, we can evaluate this to find:
θ_B ≈ 56.6°
Therefore, the angle of incidence for which the reflected light is 100% polarized is approximately 56.6°.
The correct option in the given choices is D) 56.6°.
Learn more about angle of incidence here:
https://brainly.com/question/14221826
#SPJ11
Alex Morgan is going to kick a soccer ball into the goal during the 2019 World Cup. Alex kicks the ball straight at the goal from 50.0 m away. Assume the goalie is busy faking an injury and doesn't try to stop the ball, and ignore air resistance. A. (5 points) Suppose that Alex kicks the ball with an initial speed of 19.7 m/s. What angle would she have to kick the ball so that it just makes it to the goal without touching the ground? B. (4 points) The top of the goal is 2.44 m off of the ground. Suppose instead that she kicked the ball at an initial angle of 40.0°. With what initial speed should she kick the ball in order to hit the top of the goal?
A. Alex Morgan would need to kick the ball at an angle of approximately 29.5 degrees.
B. Alex Morgan should kick the ball with an initial speed of approximately 16.5 m/s to hit the top of the goal when kicked at an angle of 40.0 degrees.
A. To determine the angle at which Alex Morgan needs to kick the ball so that it just reaches the goal without touching the ground, we can use the equations of projectile motion. We'll assume the goal is at the same height as the ground.
To find the angle of projection (θ), we can use the equation for the horizontal range of a projectile:
Range = [tex](v0^2 * sin(2\theta)) / g[/tex]
Since we want the ball to just reach the goal without touching the ground, the range should be equal to the initial distance from the goal:
50.0 m = [tex](19.7^2 * sin(2\theta)) / 9.8[/tex]
Now, we can solve this equation to find the angle θ:
sin(2θ) =[tex](50.0 m * 9.8) / (19.7 m/s)^2[/tex]
sin(2θ) = 0.4987
2θ = arcsin(0.4987)
θ ≈ 29.5 degrees
B. Now, let's determine the initial speed at which Alex Morgan should kick the ball at an angle of 40.0 degrees to hit the top of the goal.
Given:
Initial angle of projection (θ) = 40.0 degrees
Height of the top of the goal (y) = 2.44 m
Acceleration due to gravity (g) = [tex]9.8 m/s^2[/tex]
To find the initial speed (v0), we can use the equation for the maximum height of a projectile:
Maximum height =[tex](v0^2 * sin^2(\theta)) / (2g)[/tex]
Since we want the ball to reach the top of the goal, the maximum height should be equal to the height of the top of the goal:
2.44 m =[tex](v0^2 * sin^2(40.0 degrees)) / (2 * 9.8 m/s^2)[/tex]
Now, we can solve this equation to find the initial speed v0:
[tex]v0^2 = (2 * 9.8 m/s^2 * 2.44 m) / sin^2(40.0 degrees)[/tex]
v0 ≈ 16.5 m/s
To know more about initial speed, here
brainly.com/question/28060745
#SPJ4
A particle (mass =6.0mg ) moves with a speed of 4.0 km/s in a direction that makes an angle of 37ᵒ above the positive x-axis in the xy plane. At the instant it enters a magnetic field of 5.0mT [pointing in the positive x-axis] it experiences an acceleration of 8.0 m/s² going out of the xy-plane. Show that the charge of the particle is −4.0μC. [Please show a diagram for the direction!]
the charge of the particle is -4.0 μC.
Firstly, let us define the known values and list them down given below:
mass, m = 6.0 mg = 6.0 x 10^-6 kg
Speed, v = 4.0 km/s = 4.0 x 10^3 m/s
Angle, θ = 37°
Magnetic field, B = 5.0 mT = 5.0 x 10^-3 T
Acceleration, a = 8.0 m/s²
Now, we have to find the charge, q.
Let F be the magnetic force acting on the particle,
F=q(v×B) and from Newton's second law, F=ma.
Therefore,
q(v×B)=ma.......(i)
Substituting values in the above equation, we get
q[(4.0 x 10^3 m/s) × (5.0 x 10^-3 T) × sin 37°]= 6.0 x 10^-6 kg × 8.0 m/s²
We get
q = -4.0 μC
where -ve sign indicates that the charge on the particle is negative. Therefore, the charge of the particle is -4.0 μC.4
Learn more about speed:
https://brainly.com/question/13943409
#SPJ11
Mohammad slides across the ground in a straight line. How far does Mohammad
slide on the floor if he is decelerating at a constant 2.40 m/s2 and his initial velocity is
half of the velocity of the bowling ball right before it hit Mohammad in the gut?
Mohammad slides a distance of 102.3 m on the floor at a constant deceleration of 2.4 m/s².
Mohammad slides on the floor with a constant deceleration of 2.4 m/s². The initial velocity of Mohammad is half of the velocity of the bowling ball just before it hits Mohammad in the gut. If the initial velocity of the ball is v₀ and that of Mohammad is v₀/2, then according to the law of conservation of momentum, we have:mv₀ = (m/2)v₀/2 + mvfWhere, m is the mass of the bowling ball, v₀ is the initial velocity of the ball, and vf is the final velocity of the system, which is zero after the collision.
Now, we can find the initial velocity of Mohammad using the equation:m v₀ = (m/2)(v₀/2) + mvf(m v₀) - (m v₀/4) = mvf(3m/4)v₀ = mvfWe can substitute this expression for v₀ in the equation of motion for Mohammad:x = v₀t + (1/2)at²where, x is the distance travelled by Mohammad, t is the time, and a is the acceleration. Rearranging this equation, we get:t = sqrt(2x/a)Substituting the value of v₀ in this equation, we have:t = sqrt(2x/(3a))Putting the expression for v₀ in the equation of momentum, we have:3mvf/4 = m(vf + v)/2where v is the final velocity of Mohammad.
Solving for vf, we get:vf = -v/2Substituting this expression in the equation of motion for Mohammad, we have:x = (v₀/2)t + (1/2)at²Putting the expression for t in this equation, we get:x = (v₀/2)sqrt(2x/(3a)) + (1/2)at²Simplifying this expression, we get: (3/4)x = (1/2)(v₀/√(3a))t²Substituting the expression for t in this equation, we get:(3/4)x = (1/2)(v₀/√(3a)) [2x/3a]x = (v₀²/3a) [2/√(3a)]x = (v₀²/√(3a²))(4/3)Using the expression for v₀ in this equation, we get:x = [v²/(3a²)](4/3)(1/√3)x = (4/9)(v²/a)√3Putting the values, we get:x = (4/9)(20²/2.4)√3 = 102.3 m.
Hence, Mohammad slides a distance of 102.3 m on the floor at a constant deceleration of 2.4 m/s².
Learn more about velocity here,
https://brainly.com/question/80295
#SPJ11
An atom has 80 electrons, 126 neutrons, and 82 protons. What is the name of this atom? Is it electrically
charged? Write out the nuclear notation for this nucleus.
The atom with 80 electrons, 126 neutrons, and 82 protons has a nucleus with 82 protons, which means it has 82 electrons to make it electrically neutral. It is also not electrically charged. The name of this atom is lead and its nuclear notation is as follows;`208 Pb 82
The nuclear notation for this nucleus can be written as follows:
The element symbol: Pb
The atomic number (number of protons): 82 (as a subscript)
The mass number (number of protons + neutrons): 126 + 82 = 208 (as a superscript)
Therefore, the nuclear notation for this nucleus is ^208Pb.
`Where `208` is the mass number, `Pb` stands for lead and `82` is the atomic number of lead (Pb). The atomic number represents the number of protons in the nucleus of an atom.
Learn more about atoms:
https://brainly.com/question/17545314
#SPJ11
Given x1(t) = cos (t), x2(t) = sin (πt) and x3(t) = xi(t) + x2(t). a. Determine the fundamentals period of TI and T2 b. Determine if T3 is periodic or nonperiodic and shows the evident c. Determine the powers P1, P2 and P3 of each signal
The fundamental period (TI) for x1(t) is 2π, (T2) for x2(t) is 2 and x3(t) is nonperiodic. Powers P1 and P2 values are 1/2 while the power of P3 cant be determined since x3(t) is nonperiodic.
Given signals are;x1(t) = cos(t) x2(t) = sin(πt) x3(t) = x1(t) + x2(t)a) To find the fundamental period of T1;The fundamental period of a signal x(t) is denoted by T0, and it is defined as the smallest value of T such that x(t) = x(t+T) for all values of t. Therefore, x1(t) = x1(t+T1), whereT1= 2π/ω1= 2π/1= 2π. Thus, the fundamental period of x1(t) is T1= 2π.b) To find the fundamental period of T2;x2(t) = x2(t+T2), whereT2 = 2π/ω2= 2π/π= 2Thus, the fundamental period of x2(t) is T2 = 2.c) To determine if T3 is periodic or non-periodic and show the evident;x3(t) = x1(t) + x2(t) Therefore,x3(t) = cos(t) + sin(πt)If we assume T3 exists, then we can say thatx3(t) = x3(t + T3)cos(t) + sin(πt) = cos(t + T3) + sin(π(t + T3))
Therefore, the function will be periodic if the following conditions are satisfied: cos(t + T3) = cos(t)sin(π(t + T3)) = sin(πt)Expanding the above expression, cos(t + T3) = cos(t)sin(πt)cos(T3) + cos(πt)sin(πt)sin(T3) = sin(πt). Simplifying, cos(T3) = 1Therefore, T3 is a multiple of 2π. Also, sin(T3) = 0.If T3 exists, it must be a multiple of T1 and T2.LCM(T1, T2) = LCM(2π, 2) = 2πThe multiple of 2π is 2π itself. Therefore, T3 = 2πd, where d is a constant. But since sin(T3) = 0, d must be an even integer.T3 is periodic with a fundamental period of 2πd. Thus, T3 = 4π.d) To determine the power P1, P2 and P3 of each signal; Power is defined as the average value of the energy carried by the signal over the given time.T1 = 2π, ω1 = 1; P1 = (1/T1)∫(T1/2)^(T1/2)x1^2(t) dt= (1/2π) ∫π^(-π) cos^2(t) dt= 1/2.T2 = 2, ω2 = π; P2 = (1/T2)∫(T2/2)^0x2^2(t) dt= (1/4) ∫2^0 sin^2(πt) dt= 1/4.T3 = 4π; P3 = (1/T3)∫(T3/2)^(-T3/2)x3^2(t) dt= (1/8π) ∫2π^(-2π) (cos(t) + sin(πt))^2 dt= (1/8π) [π + 2] = (π + 2)/8π.
Learn more about fundamental period:
https://brainly.com/question/15861094
#SPJ11
A 50-cm-diameter pipeline in the Arctic carries hot oil where the outer surface is maintained at 30°C and is exposed to a surrounding temperature of -12°C. Aspecial powder insulation 5 cm thick surrounds the pipe and has a thermal conductivity of 7mW/m°C.The convection heat-transfer coefficient on the outside of the pipe is 9 W/m2°C. Estimate the energy loss from the pipe per meter of length.
To estimate the energy loss from the pipe per meter of length, we consider the heat transfer through conduction and convection.
The heat transfer through conduction can be calculated using the formula: Q_conduction = (k * A * (T_inner - T_outer)) / d,
Q_conduction = (0.007 W/m°C * π * (0.5 m)² * (30°C - (-12°C))) / 0.05 m.
Next, we need to calculate the heat transfer through convection using the formula:
Q_convection = h * A * (T_inner - T_surrounding),
Q_convection = 9 W/m²°C * π * (0.5 m)² * (30°C - (-12°C)).
Calculating this expression, we find the heat transfer through convection.
Finally, we can find the total energy loss per meter of length by adding the heat transfer through conduction and convection.
Please note that the numerical values provided in the question were not specified, so the final result will depend on the specific values used.
Learn more about energy here;
https://brainly.com/question/8101588
#SPJ11
Find the components of the following vectors using trigonometric functions a. The wind is blowing at 77 km/h N 25° W b. A car accelerates at 4.55 m/s² at a bearing of 117" c. Sally and Sandy walk 18 m up a ramp, inclined at 33" from the horizontal. How far forward and how far upward did they go? 1
(a), the wind speed is given as 77 km/h at a direction of N 25° W. In case (b) car's acceleration is given as 4.55 m/s² at a bearing of 117°.
(c) In case Sally & Sandy walk up a ramp inclined at 33° from horizontal for a distance of 18 m. The horizontal and vertical components of each vector can be determined using trigonometric functions.
In case (a), to find the components of the wind vector, The north-south component can be found by multiplying the wind speed by sine of 25°, while east-west component can be found by multiplying the wind speed by the cosine of 25°.
In case (b), the acceleration vector can be split into its horizontal and vertical components using the sine and cosine functions. The vertical component can be found by multiplying the acceleration magnitude by the sine of 117°.
In case (c), the distance traveled up ramp can be found by multiplying and the distance traveled forwar can be found by multiplying the given distance by the cosine of 33°.
By applying appropriate trigonometric functions to each case, the horizontal and vertical components of the vectors can be determined.
Learn more about components here;
https://brainly.com/question/3214758
#SPJ11
Suppose you try to cool the kitchen of your house by leaving the refrigerator door open. What happens? Why? Would the result be the same if you left open a picnic cooler full of ice? Explain the reason for any differences.
Is it a violation of the second law of thermodynamics to convert mechanical energy completely into heat? To convert heat completely into work? Explain your answers.
Real heat engines, like the gasoline engine in a car, always have some friction between their moving parts, although lubricants keep the friction to a minimum. Would a heat engine with completely frictionless parts be 100% efficient? Why or why not? Does the answer depend on whether or not the engine runs on the Carnot cycle? Again, why or why not?
A heat engine with completely frictionless parts would still not be 100% efficient even if it ran on the Carnot cycle.
Suppose you try to cool the kitchen of your house by leaving the refrigerator door open. What happens? Why?Would the result be the same if you left open a picnic cooler full of ice? Explain the reason for any differences.If you leave the refrigerator door open, the room may become slightly colder initially, but the overall effect will be to warm up the room. This is because the refrigerator will work to cool down the air inside it but at the same time will pump the heat out into the room. As a result, the room’s temperature will rise. If you left a picnic cooler full of ice open in the room, the ice would eventually melt and the water would eventually warm up to room temperature, raising the temperature of the room.
However, the cooling effect of the ice will be greater than the heating effect of the air that escapes. Therefore, it will be more efficient in cooling the room for a shorter time.Is it a violation of the second law of thermodynamics to convert mechanical energy completely into heat? To convert heat completely into work? Explain your answers.No, it is not a violation of the second law of thermodynamics to convert mechanical energy completely into heat because heat is a form of energy, and the second law of thermodynamics states that energy cannot be created or destroyed; it can only be transferred or converted from one form to another.
However, it is impossible to convert heat completely into work because some heat energy will always be lost to the environment, and the second law of thermodynamics prohibits the conversion of heat energy completely into work.Real heat engines, like the gasoline engine in a car, always have some friction between their moving parts, although lubricants keep the friction to a minimum. Would a heat engine with completely frictionless parts be 100% efficient? Why or why not? Does the answer depend on whether or not the engine runs on the Carnot cycle?
Again, why or why not?A heat engine with completely frictionless parts would not be 100% efficient because some energy would still be lost as heat due to the second law of thermodynamics. The answer does not depend on whether or not the engine runs on the Carnot cycle because the Carnot cycle assumes an ideal engine with no friction, which is not possible in the real world. Therefore, a heat engine with completely frictionless parts would still not be 100% efficient even if it ran on the Carnot cycle.
Learn more about Thermodynamics here,
https://brainly.com/question/13059309
#SPJ11
A 0.250 kg mass is attached to a horizontal spring of spring constant 140 N/m, supported by a frictionless table. A physics student pulls the mass 0.12 m from equilibrium, and the mass is then let go. Assume no air resistance and that it undergoes simple harmonic motion.
a) Calculate the work done by the student on the mass in pulling it a distance of 0.12 m.
b) Using conservation of energy principles, calculate the maximum speed of the mass.
a) The work done by the student on the mass in pulling it a distance of 0.12 m is 0.10 J.b) The maximum speed of the mass is 0.79 m/s.
a) Work done by the student on the mass in pulling it a distance of 0.12 m.The amount of work done by the student is equal to the amount of potential energy stored in the spring.Potential energy stored in the spring = 1/2 kx²where, k is the spring constant and x is the displacement from the equilibrium position.Now, the displacement of the mass is given as 0.12 m.Substituting the given values,1/2 × 140 N/m × (0.12 m)² = 0.10 JTherefore, the work done by the student on the mass in pulling it a distance of 0.12 m is 0.10 J.
b) Maximum speed of the massUsing the law of conservation of energy, the potential energy stored in the spring is equal to the kinetic energy of the mass at the maximum speed.Potential energy stored in the spring = Kinetic energy of the mass at maximum speed1/2 kA² = 1/2 mv²where, A is the amplitude, m is the mass, and v is the maximum velocity of the mass.Substituting the given values,1/2 × 140 N/m × (0.12 m)² = 1/2 × 0.250 kg × v²Solving for v, v = 0.79 m/sTherefore, the maximum speed of the mass is 0.79 m/s.
Learn more about Potential energy here,
https://brainly.com/question/21175118
#SPJ11
Why does the lower part of the child appear so much different in size from the upper part?
*
Captionless Image
The light rays that travel through water and then into air are refracted.
The light rays that travel through air and then into water are reflected.
The light rays that travel through water and then into air are enlarged.
The light rays that travel through air and then into water are reduced.
The size difference between the upper and lower parts of the child in the image is caused by refraction, where light bending in water makes the submerged part appear bigger.
The lower part of the child appears much different in size from the upper part due to the phenomenon of refraction. Refraction is the bending of light as it passes through a substance of different refractive indices. The refractive index of water is higher than that of air. As a result, when light rays pass from water into the air, they have refracted away from the normal and the image appears enlarged. In this image, the child is partially submerged in water. Therefore, the light rays coming from the lower part of the child are refracted as they pass from water to air, making the lower part of the child appear bigger. On the other hand, the upper part of the child is not submerged in water, and the light rays coming from the upper part pass through the air only, making the upper part appear smaller by comparison. In summary, the difference in size between the upper and lower parts of the child in the image is due to the phenomenon of refraction.For more questions on refraction
https://brainly.com/question/27932095
#SPJ8
In the figure particle 1 of charge q1 = +e and particle 2 of charge q2 = –6e are fixed on an x axis. Distance d = 7.40 μm. What is the electric potential difference (in V) VA – VB?
the electric potential difference VA – VB is 13.54 V.
The given charges in the figure are particle 1 of charge q1 = +e and particle 2 of charge q2 = -6e, and they are fixed on the x-axis at a distance of d = 7.40 μm. The electric potential difference (in V) VA – VB is to be determined.However, there is no point C between A and B in the figure. Hence, it is not possible to determine the potential difference between A and B. Instead, we can calculate the potential at points A and B due to charges q1 and q2, respectively. Then, we can subtract VB from VA to get the potential difference VA – VB.
Let's calculate the potentials at A and B.Using the electric potential formula for a point charge V = kq/r where k = 9 × 10^9 N m²/C² is Coulomb's constant, we get:VA = kq1/RA= (9 × 10^9 N m²/C²)(1.6 × 10^-19 C)/(7.4 × 10^-6 m)= 1.94 VVB = kq2/RB= (9 × 10^9 N m²/C²)(-6 × 1.6 × 10^-19 C)/(7.4 × 10^-6 m)= -11.6 VTherefore,VA – VB= (1.94 V) - (-11.6 V)= 13.54 VTherefore, the electric potential difference VA – VB is 13.54 V.
Learn more about constant here,
https://brainly.com/question/27983400
#SPJ11
The cycle below described by a perfect gas in the diagram (P, V) is considered.
To describe such a cycle, the gas is successively in contact with two thermostats: one, the hot source at temperature T1 = 300 K; the other, the cold source at temperature T2 = 250 K.
Gas transformations are reversible. AB and CD transformations are therefore isotherms and BC and DA transformations are adiabatics (no heat exchange). The heat received by the gas in the CD isothermal transformation is Q2 = 1000 kJ.
1)What is the entropy variation for the ABCDA cycle?
2) Calculate the heat Ql received by the gas in the ISothermal transformation AB.
1) The entropy variation for the ABCDA cycle is 150.2) The heat Ql received by the gas in the isothermal transformation AB is 832.8kJ.What is the definition of entropy?Entropy is the extent of the randomness or the molecular disorder of a system. Entropy is a measure of the degree of disorder of a system.
The units of entropy are joules per kelvin per mole (J K-1 mol-1).What is the definition of the first law of thermodynamics?The First Law of Thermodynamics is a statement of the Law of Energy Conservation, which states that energy cannot be created or destroyed, but it can be converted from one form to another. The first law of thermodynamics is also known as the Law of Conservation of Energy.What is the definition of the second law of thermodynamics?The second law of thermodynamics is an assertion that all physical processes or spontaneous transformations of energy go from states of higher order to states of lower order, that the entropy of an isolated system will tend to increase over time, approaching a maximum value at equilibrium. The second law of thermodynamics is responsible for the flow of heat from hot to cold and for the impossibility of building perpetual motion machines.
Learn more on entropy here:
brainly.in/question/15044680
#SPJ11
Describe the image properties when the converging mirror (Concave) has an object closer to it than its focal length?
When an object is positioned closer to a concave (converging) mirror than its focal length, the image formed will have the following properties: 1. Virtual Image, 2. Enlarged Image, 3. Upright Orientation, 4. Reduced Distance, 5. Realism.
1. Virtual Image: The image formed will be virtual, meaning it cannot be projected onto a screen. It can only be seen when looking into the mirror.
2. Enlarged Image: The image will be magnified compared to the size of the object. The height of the image will be greater than the height of the object.
3. Upright Orientation: The image will be upright, meaning it will have the same orientation as the object. This occurs because the light rays from the object diverge and then appear to converge from behind the mirror, forming the virtual image.
4. Reduced Distance: The image will appear closer to the mirror than the object itself. The distance between the mirror and the image will be smaller than the distance between the mirror and the object.
5. Realism: Although the image is virtual, it appears as if it is a real object located behind the mirror. This is due to the apparent path of the light rays.
Overall, when an object is placed closer to a concave mirror than its focal length, a magnified, upright, virtual image is formed that appears closer to the mirror than the object itself.
Learn more about focal length
https://brainly.com/question/31755962
#SPJ11
Calculate the angle of refraction for light traveling at 19.4O from oil (n = 1.65) into water (n= 1.33)?
If the light then travels back into the oil at what angle will it refract?
The obtained angle θ4 will be the angle of refraction when light travels back into the oil. The angle of refraction when light travels from oil to water, we can use Snell's law, which relates the angles of incidence and refraction to the refractive indices of the two media.
Snell's law states: [tex]n_1\\[/tex] * sin(θ1) = [tex]n_2[/tex] * sin(θ2)
Where
[tex]n_1[/tex] and [tex]n_2[/tex] are the refractive indices of the initial and final media, respectively.
θ1 is the angle of incidence.
θ2 is the angle of refraction.
Given:
[tex]n_1[/tex] = 1.65 (refractive index of oil)
[tex]n_2[/tex] = 1.33 (refractive index of water)
θ1 = 19.4°
We can rearrange Snell's law to solve for θ2:
sin(θ2) = ([tex]n_1 / n_2[/tex]) * sin(θ1)
Substituting the given values:
sin(θ2) = (1.65 / 1.33) * sin(19.4°)
Taking the inverse sine of both sides:
θ2 = sin((1.65 / 1.33) * sin(19.4°))
Calculating this expression will give us the angle of refraction when light travels from oil to water.
If the light then travels back into the oil, we can use Snell's law again. The angle of incidence will be the angle of refraction obtained when light traveled from water to oil, and the angle of refraction will be the angle of incidence in this case.
Let's assume the angle of refraction obtained when light traveled from water to oil is θ3. The angle of incidence when light travels from oil to water will be θ3, and we can use Snell's law to find the angle of refraction in the oil:
[tex]n_2[/tex] * sin(θ3) = [tex]n_1[/tex] * sin(θ4)
Rearranging the equation:
sin(θ4) = ([tex]n_2 / n_1[/tex]) * sin(θ3)
Substituting the refractive indices:
sin(θ4) = (1.33 / 1.65) * sin(θ3)
Taking the inverse sine of both sides:
θ4 = sin((1.33 / 1.65) * sin(θ3))
The obtained angle θ4 will be the angle of refraction when light travels back into the oil.
Learn more about refraction here:
https://brainly.com/question/14760207
#SPJ11
A parallel plate capacitor, in which the space between the plates is filled with a dielectric material with dielectric constant κ=16. 9
, has a capacitor of V=19. 9μF
and it is connected to a battery whose voltage is C=65. 8V
and fully charged. Once it is fully charged, while still connected to the battery, dielectric material is removed from the capacitor. How much change occurs in the energy of the capacitor (final energy minus initial energy)? Express your answer in units of mJ (mili joules) using two decimal places.
To determine the change in energy of the capacitor when the dielectric material is removed, we need to calculate the initial and final energies and then find the difference between them.
The energy stored in a capacitor is given by the formula:
E = 0.5 * C * V^2
Given:
Capacitance (C) = 19.9 μF = 19.9 × 10^(-6) F
Voltage (V) = 65.8 V
Dielectric constant (κ) = 16.9
Let's first calculate the initial energy when the dielectric material is present:
Initial Energy (E_initial) = 0.5 * C * V^2
Next, we need to calculate the final energy after the dielectric material is removed. Since the dielectric constant is removed, the effective capacitance of the capacitor will change.
The new capacitance without the dielectric can be calculated using the equation:
C_new = C / κ
Now we can calculate the final energy:
Final Energy (E_final) = 0.5 * C_new * V^2
To find the change in energy:
ΔE = E_final - E_initial
Let's perform the calculations:
E_initial = 0.5 * (19.9 × 10^(-6)) * (65.8)^2
C_new = (19.9 × 10^(-6)) / 16.9
E_final = 0.5 * C_new * (65.8)^2
ΔE = E_final - E_initial
Calculating ΔE will give us the change in energy of the capacitor.
Please note that the result will be provided in units of mJ (mili joules) with two decimal places.
To know more about "Capacitance" refer here:
brainly.com/question/29591088#
#SPJ11
An object is placed 45 cm to the left of a converging lens of focal length with a magnitude of 25 cm. Then a diverging lens of focal length of magnitude 15 cm is placed 35 cm to the right of this lens. Where does the final image form for this combination? in cm with appropriate sign with respect to diverging lens, real of virtual image?(make sure to answer this last part)
The image distance for the diverging lens (v_diverging) will be the object distance for the converging lens (u_converging). Using the values obtained for v_converging and v_diverging, we can determine the final image distance and whether it is a real or virtual image.
To find the final image formed by the combination of lenses, we can use the lens formula and the concept of image formation.
Let's consider the converging lens first. The lens formula is given by:
1/f_converging = 1/v_converging - 1/u_converging
where f_converging is the focal length of the converging lens, v_converging is the image distance, and u_converging is the object distance.
Given that the object is placed 45 cm to the left of the converging lens (u_converging = -45 cm) and the focal length of the converging lens is 25 cm (f_converging = 25 cm), we can calculate v_converging.
1/25 = 1/v_converging - 1/(-45)
Simplifying this equation will give us the value of v_converging.
Now let's consider the diverging lens. The lens formula for the diverging lens is:
1/f_diverging = 1/v_diverging - 1/u_diverging
where f_diverging is the focal length of the diverging lens, v_diverging is the image distance, and u_diverging is the object distance.
In this case, the object is placed 35 cm to the right of the diverging lens (u_diverging = 35 cm) and the focal length of the diverging lens is 15 cm (f_diverging = -15 cm, negative because it's a diverging lens).
Using the lens formula, we can calculate v_diverging.
Now, to determine the final image formed by the combination of lenses, we need to consider the relative position of the two lenses. Since the diverging lens is placed to the right of the converging lens, the image formed by the converging lens will act as the object for the diverging lens.
To know more about converging lens
https://brainly.com/question/29178301
#SPJ11
Why are thire only large impact craters on Venus?
A. There are only large impact craters on Venus because only large meteors and asteroids survive their fall through the planet's thick and corrosive atmosphere.
B. There are only large impact craters on Venus because geological activity erodes impact craters over time.
C. There are only large impact craters on Venus because most smaller asteroids and meteors have been cleared out of the inner solar system over the last few billion years.
D. There are only large impact craters on Venus because the weather on the planet erodes impact craters over time.
E. There are actually impact craters of all sizes on the surface of Venus.
Venus has large impact craters due to the absence of erosive forces and the survival of only the largest meteors and asteroids through its thick atmosphere.
Option (A) is correct.
Venus, known as the sister planet of Earth, is characterized by its thick, corrosive atmosphere and extreme temperatures. Its surface lacks water and volcanic activity, and is instead marked by numerous large impact craters. This is due to the absence of erosive forces, like water, which would have gradually eroded the craters over billions of years. The craters formed on Venus as a result of asteroid and comet impacts over the past 4.6 billion years. However, the impact process on Venus differs from that on Earth. Venus' thick atmosphere burns up most smaller meteorites and asteroids upon entry, allowing only the largest ones to survive their descent. Consequently, only the large impact craters remain visible on the planet's surface today. Therefore, option (A) is correct. In summary, Venus bears only large impact craters as a consequence of the survival of substantial meteors and asteroids through its thick and corrosive atmosphere.
Learn more about erosive forces
https://brainly.com/question/12976130
#SPJ11
What is the estimated volume of the table tennis ball?
cm3
What is the estimated volume of the golf ball?
cm3
Answer:
The estimated volume of a standard table tennis ball is approximately 2.7 cm³.
The estimated volume of a standard golf ball is approximately 41.6 cm³.
Explanation:
Calculate the following quantities and write their units in terms of basic units: a) The density when the mass is 2.532 kg and the volume is 162 cm3. b) The volume of a container has a capacity of 2.5 liters. c) The area of a pool has 2km long by 4 km wide.
a) Density is calculated by dividing mass by volume. Density = Mass / Volume = 2.532 kg / 162 cm³. Convert cm³ to m³. Since 1 m = 100 cm, 1 m³ = (100 cm)³ = 1,000,000 cm³.
Density = 2.532 kg / (162 cm³ * (1 m³ / 1,000,000 cm³)) = 15,629.63 kg/m³
b) The volume of the container is given as 2.5 liters. To express it in basic units,Since 1 liter = 0.001 m³, the volume of the container in cubic meters is: Volume = 2.5 liters * 0.001 m³/liter = 0.0025 m³
c) The area of the pool is given as 2 km by 4 km. To express it in basic units, Since 1 km = 1000 m, the area of the pool is:
Area = 2 km * 4 km * (1000 m/km) * (1000 m/km) = 8,000,000 m²
In physics, volume is a fundamental quantity that measures the amount of three-dimensional space occupied by an object or a substance. It is typically measured in cubic units such as cubic meters (m³) or cubic centimeters (cm³), and is an important parameter in various physical calculations and equations.
Learn more about Volume here:
https://brainly.com/question/14197390
#SPJ11
A beam of light strikes the surface of glass (n = 1.46) at an angle of 70° with respect to the normal. Find the angle of refraction inside the glass. Take the inder of refraction of air n₁ = 1.
The given case is not possible. The given parameters must be incorrect.Conclusion:The given parameters must be incorrect because the value of sin cannot be greater than 1. Hence the angle of refraction inside the glass cannot be calculated.
Given parameters are,n = refractive index of glassn₁ = refractive index of airAngle of incidence (i) = 70°We are required to calculate the angle of refraction (r) inside the glass.To calculate the angle of refraction inside the glass, we can use Snell’s law.Snells law states that the ratio of the sines of the angle of incidence (i) and the angle of refraction (r) is equal to the ratio of the refractive indices of two media. i.e.,sin i / sin r = n1 / n2
Where,n₁ = Refractive index of air = 1n₂ = Refractive index of glass = 1.46sin i / sin r = 1 / 1.46 sin r = (sin i) x (n2 / n1)sin r = sin 70° × (1.46 / 1) = 1.2351The value of sin cannot be greater than 1. Hence, the given case is not possible. The given parameters must be incorrect.Conclusion:The given parameters must be incorrect because the value of sin cannot be greater than 1. Hence the angle of refraction inside the glass cannot be calculated.
Learn more about Refractive here,
https://brainly.com/question/83184
#SPJ11
Analyse the stick diagram as shown in Figure Q2(b). (i) Transform the stick diagram into the equivalent schematic circuit at transistor level. (10 marks) (ii) Determine the Boolean equation representing the output Y. (4 marks) Figure Q2(b)
The above schematic circuit diagram is the equivalent schematic circuit at transistor level.
The Boolean equation representing the output Y is X + Z.
(i) Transformation of stick diagram into an equivalent schematic circuit at transistor level
The stick diagram given above represents the schematic diagram of the given Boolean expression using only MOS transistors as per the design rules. The stick diagram can be transformed into the equivalent schematic circuit at transistor level as shown below:
The above schematic circuit diagram is the equivalent schematic circuit at transistor level.
(ii) Determination of Boolean equation representing the output Y Boolean equation can be formed by observing the schematic circuit diagram obtained from the stick diagram.
The output of the given circuit diagram is represented by the output terminal Y which is labelled in the circuit diagram obtained above. The output Y is formed by OR operation of the two input terminals X and Z as seen in the diagram. Therefore the Boolean equation representing the output Y is given as:
Y = X + Z.
The Boolean equation representing the output Y is X + Z.
Learn more about Boolean https://brainly.com/question/2467366
#SPJ11
The capacitance of an empty capacitor is 6.60 uF. The capacitor is connected to a 12-V battery and charged up. With the capacitor connected to the battery, a slab of dielectric material is inserted between the plates. As a result, 5.00 x 105 C of additional charge flows from one plate, through the battery, and onto the other plate. What is the dielectric constant of the material?
The dielectric constant of the material can be calculated from the capacitance of the capacitor with the dielectric slab, given that the capacitance with an empty capacitor is 6.60 uF and that 5.00 x 10⁵ C of additional charge flows through the battery.
What is the dielectric constant of the material?
The formula used for the calculation of the dielectric constant of the material is given by;`C = (Kε_0A)/d`Where,K = dielectric constantε₀ = vacuum permittivity (8.85 x 10⁻¹² F/m)d = separation of platesA = area of the plateC = capacitance of the capacitorGiven that the capacitance of the empty capacitor `C = 6.60 uF`Charge flown = `Q = 5.00 x 10⁵ C`Voltage = `V = 12 V`From the formula for capacitance,`C = Q/V`
The capacitance of the capacitor with the dielectric material can be calculated by adding the additional charge flown into the capacitor to the initial charge.`C' = (Q + 5.00 x 10⁵ C)/V``C' = (Q/V) + (5.00 x 10⁵ C)/V``C' = 6.60 + 5.00 x 10⁵ / 12`The capacitance with the dielectric material `C' = 6.60 + 41667 F` `= 41673.3 F`The dielectric constant of the material can be calculated by substituting the values of the capacitance of the capacitor with the dielectric material and that of the vacuum permittivity into the formula for capacitance.`
C' = (Kε_0A)/d``K = (C'd)/(ε₀A)`Substituting the values into the above formula;`K = (41673.3 x 3.8 x 10⁻¹¹)/(3.6 x 10⁻⁴)` `= 4398.3`
Hence, the dielectric constant of the material is 4398.3.
How to calculate the dielectric constant of the material?
The dielectric constant of the material can be calculated from the capacitance of the capacitor with the dielectric slab, given that the capacitance with an empty capacitor is 6.60 uF and that 5.00 x 10⁵ C of additional charge flows through the battery.
Learn more about Vacuum here,
https://brainly.com/question/30595230
#SPJ11
An air-track glider is attached to a spring. The glider is pulled to the right and released from rest at t=0 s. It then oscillates with a period of 1.8 s and a maximum speed of 46 cm/s. Part A What is the amplitude of the oscillation? Express your answer in centimeters. A=13 cm What is the glider's position at t=0.26 s ? Express your answer in centimeters. A 1.10 kg block is attached to a spring with spring constant 14 N/m. While the block is sitting at rest, a student hits it with a hammer and almost instantaneously gives it a speed of 33 cm/s. Part A What is the amplitude of the subsequent oscillations? Express your answer in centimeters. A=9.3 cm What is the block's speed at the point where x=0.75A ? Express your answer in centimeters per second.
Part A The amplitude of the oscillation is 13 cm. the glider's position at t = 0.26 s is approximately -9.8 cm.the amplitude of the subsequent oscillations is 9.3 cm. Part B the required velocity of the block at the point where x = 0.75A is v = A√(k / m) = 9.3√(14 / 1.10) = 31 cm/s
Given,Period, T = 1.8 s Maximum Speed, vmax = 46 cm/sLet Amplitude, A be the amplitude of the oscillation.Part A Amplitude of the oscillation Amplitude of the oscillation is given by;A = vmax * T / (2 * π)Substitute the given values,A = (46 cm/s) * (1.8 s) / (2 * 3.14)A = 13 cm Therefore, the amplitude of the oscillation is 13 cm. Part B Position of the glider at t = 0.26 sThe general equation for displacement of the glider with time is given by;x = A cos (ωt + φ)Where A is the amplitude, ω is the angular frequency and φ is the phase constant.At time t = 0, x = A cos φThe velocity of the glider is maximum at the mean position and zero at the extremities.
Therefore, the glider will cross the mean position when cos(ωt + φ) = 0that is,ωt + φ = 90°ωt = 90° - φ..................(1)Also given, Period T = 1.8 sSo, Angular frequency, ω = 2π / T = 2π / 1.8 rad/s Substitute the given values in (1)0.26 s = (90° - φ) / (2π / 1.8)0.26 s = (90° - φ) * 1.8 / 2πφ = 1.397 radx = A cos (ωt + φ)x = A cos [ω(0.26) + 1.397]x = A cos (0.753 + 1.397) = A cos 2.15 = -9.8 cm (Approx)Therefore, the glider's position at t = 0.26 s is approximately -9.8 cm.
A 1.10 kg block is attached to a spring with spring constant 14 N/m. Let the amplitude of the subsequent oscillations be A. Let vmax be the maximum velocity and v be the velocity of the block when x = 0.75A.Part A Amplitude of the subsequent oscillation Amplitude of the subsequent oscillation is given by,A = vmax / ωWhere ω is the angular frequencySubstitute the given values,vmax = A * ωHence,A = vmax / ω = √(k / m) * A = √(14 N/m / 1.10 kg) * A = 3.09A = 9.3 cmTherefore, the amplitude of the subsequent oscillations is 9.3 cm.
Part B Velocity of the block at x = 0.75ATotal energy of the system is given by;E = 1/2 kA²At x = 0.75A, the block has only potential energy.E = 1/2 k(0.75A)²= 0.42 kA²Total energy is also given by,E = 1/2 mv²v = √(2E / m)= √(kA² / m)= A√(k / m)At x = 0.75A, v = A√(k / m)At x = 0.75A,A = 9.3 cmK = 14 N/mM = 1.10 kgTherefore, the required velocity of the block at the point where x = 0.75A is v = A√(k / m) = 9.3√(14 / 1.10) = 31 cm/s (Approx).
Learn more about velocity here,
https://brainly.com/question/80295
#SPJ11
A Force of F= (4.20i +3.60j) N is applied to a rigid body of mass 1.50 kg rotating around a fixed axis . Determine the torque experienced by the particle when the force is applied at the position of r= (1.50i+ 2.20j)
Which direction is the Torque oriented?
The torque experienced by the particle is 10.38 N·m, and its direction is perpendicular to the plane formed by the position vector and the force vector.
To determine the torque experienced by the particle, we need to calculate the cross product of the position vector and the force vector. The formula for torque is given by:
τ = r × F
where τ represents the torque, r is the position vector, and F is the force vector. In this case, the position vector r is (1.50i + 2.20j) and the force vector F is (4.20i + 3.60j).
Taking the cross product of these vectors, we have:
τ = (1.50i + 2.20j) × (4.20i + 3.60j)
Expanding the cross product, we get:
τ = (1.50 * 3.60 - 2.20 * 4.20)k
Simplifying the equation, we have:
τ = (5.40 - 9.24)k
τ = -3.84k
Therefore, the torque experienced by the particle is -3.84 N·m. The negative sign indicates that the torque is oriented in the opposite direction to the positive z-axis.
Since torque is a vector quantity, it has both magnitude and direction. The direction of the torque is determined by the right-hand rule. In this case, the torque is oriented along the negative z-axis, which means it is pointing into the plane formed by the position vector and the force vector.
Learn more about magnitude here:
https://brainly.com/question/31022175
#SPJ11
A billiard ball moving across the table at 1.50 m/s makes a head on elastic collision with an identical ball. Find the velocities of each ball after the collision: (a) when the 2nd ball is initially at rest, velocity of ball 1: _______ velocity of ball 2: ________
(b) when the 2nd ball is moving toward the first with a speed of 1.00 m/s, velocity of ball 1: ___________ velocity of ball 2: __________ (c) when the 2nd ball is moving away from the first with a speed of 1.00 m/s, velocity of ball 1: __________ velocity of ball 2: ____________
When the 2nd ball is initially at rest, the velocity of ball 1 is 0 m/s and the velocity of ball 2 is 1.50 m/s. When the 2nd ball is moving toward the first with a speed of 1.00 m/s, the velocity of ball 1 is 0.25 m/s and the velocity of ball 2 is 1.25 m/s.
The formula for elastic collision is:
v1f = (m1 - m2)/(m1 + m2) * v1i + 2m2/(m1 + m2) * v2i
v2f = 2m1/(m1 + m2) * v1i + (m2 - m1)/(m1 + m2) * v2i
Given:
Initial velocity of ball 1, v1i = 1.50 m/s
Initial velocity of ball 2, v2i = 0 m/s (initially at rest)
Mass of ball 1 = Mass of ball 2
Calculations:
(a) When the 2nd ball is initially at rest:
Total mass, m = m1 + m2 = m1 + m1 = 2m1
Let's assume the final velocity of ball 1 and ball 2 are v1f and v2f, respectively.
v1f = (m1 - m1)/(2m1) * 1.50 m/s + 2m1/(2m1) * 0 m/s
v1f = 0 m/s
v2f = 2m1/(2m1) * 1.50 m/s + (m1 - m1)/(2m1) * 0 m/s
v2f = 1.50 m/s
(b) When the 2nd ball is moving toward the first with a speed of 1.00 m/s:
Initial velocity of ball 2, v2i = -1.00 m/s (moving towards ball 1)
Total mass, m = m1 + m2 = m1 + m1 = 2m1
Let's assume the final velocity of ball 1 and ball 2 are v1f and v2f, respectively.
v1f = (m1 - m1)/(2m1) * 1.50 m/s + 2m1/(2m1) * (-1.00 m/s)
v1f = -0.25 m/s
v2f = 2m1/(2m1) * 1.50 m/s + (m1 - m1)/(2m1) * (-1.00 m/s)
v2f = 1.25 m/s
(c) When the 2nd ball is moving away from the first with a speed of 1.00 m/s:
Initial velocity of ball 2, v2i = 1.00 m/s (moving away from ball 1)
Total mass, m = m1 + m2 = m1 + m1 = 2m1
Let's assume the final velocity of ball 1 and ball 2 are v1f and v2f, respectively.
v1f = (m1 - m1)/(2m1) * 1.50 m/s + 2m1/(2m1) * 1.00 m/s
v1f = 0.25 m/s
v2f = 2m1/(2m1) * 1.50 m/s + (m1 - m1)/(2m1) * 1.00 m/s
v2f = 1.25 m/s
Hence the velocities of each ball after the collision are as follows:
(a) when the 2nd ball is initially at rest, velocity of ball 1: 0 m/s, velocity of ball 2: 1.50 m/s
(b) when the 2nd ball is moving toward the first with a speed of 1.00 m/s, velocity of ball 1: 0.25 m/s, velocity of ball 2: 1.25 m/s.
Learn more about velocity: https://brainly.com/question/80295
#SPJ11
In February 1955, a paratrooper fell 370 m from an airplane without being able to open his chute but happened to land in snow, suffering only minor injuries. Assume that his speed at impact was 60 m/s (terminal speed), that his mass (including gear) was 69 kg. and that the magnitude of the force on him from the snow was at the survivable limit of 1.4 x 10⁵ N. What are (a) the minimum depth of snow that would have stopped him safely and (b) the magnitude of the impulse on him from the snow? (a) Number ___________ Units _____________
(b) Number ___________ Units _____________
The minimum depth of snow that would have stopped the paratrooper safely is 0.88 m, and the magnitude of the impulse on the paratrooper from the snow is 4126.18 N s. Number: 0.88 m; Units: meters. Number: 4126.18 N s; Units: Newton second.
Magnitude is a measure of the quantity of an item, and it usually refers to the size or degree of something. Impulse is a measure of the amount of force or energy exerted on an object, and it is defined as the product of force and time.
The minimum depth of snow that would have stopped him safely and the magnitude of the impulse on him from the snow can be calculated as follows:
(a)The total force acting on the paratrooper, F, is equal to the magnitude of the force from the snow, F snow, which is equal to 1.4 x 10⁵ N, so we have:
F = Fsnow = 1.4 x 10⁵ N
The velocity of the paratrooper just before he hits the snow, v, is equal to 60 m/s.
The work done on the paratrooper by the snow, W, is given by the equation:
W = Fd
where d is the distance over which the snow acts to stop the paratrooper. Since the paratrooper comes to a stop when he hits the snow, the work done by the snow must be equal to the kinetic energy of the paratrooper just before he hits the snow, which is given by:
KE = 1/2mv²
where m is the mass of the paratrooper including his gear, which is 69 kg.
Therefore, we have:
W = KE = 1/2mv²= 1/2 x 69 x 60²= 124,200 J
Substituting W and F into the equation for work, we obtain:
d = W/Fsnow= 124200 J / 1.4 x 10⁵ N= 0.88 m
(b)The impulse, J, on the paratrooper from the snow is given by:
J = F∆t
where F is the force on the paratrooper from the snow, which is 1.4 x 10^5 N, and ∆t is the time for which the snow exerts this force on the paratrooper. Since the paratrooper comes to a stop when he hits the snow, the time for which the snow exerts a force on him is equal to the time it takes for him to come to a stop.
This time can be calculated using the equation:
v = u + at
where u is the initial velocity, which is 60 m/s, v is the final velocity, which is 0 m/s, a is the acceleration, and t is the time.The acceleration of the paratrooper as he comes to a stop in the snow, a, can be calculated using the equation:
F = ma,
where m is the mass of the paratrooper, which is 69 kg.
Therefore, we have:
a = F/m = 1.4 x 10⁵ N / 69 kg= 2029.71 m/s²
Substituting u, v, and a into the equation for motion, we obtain:
t = (v - u) / a= (0 - 60) / -2029.71= 0.02947 s
Substituting F and t into the equation for impulse, we obtain:
J = F∆t= 1.4 x 10⁵ N x 0.02947 s= 4126.18 N s
Number: 0.88 m; Units: mNumber: 4126.18 N s; Units: N s
Learn more about magnitude at: https://brainly.com/question/30337362
#SPJ11
11. A \( 30.0 \)-g bullet is fired from a gun and posssesses \( 1750 \mathrm{~J} \) of kinetic energy. Find its velocity.
Velocity of the bullet is 341.64 m/s.
Given,Mass of the bullet, m = 30.0 g = 0.03 kg Kinetic energy of the bullet, K.E = 1750 JWe know that,The kinetic energy of an object is given by the formula,K.E = (1/2) mv²where,m is the mass of the object,v is the velocity of the objectWe can write the above equation as,v = √(2K.E/m)Substituting the given values, we get,v = √(2 × 1750 / 0.03) = √(3500/0.03) = √116666.67 = 341.64 m/sTherefore, the velocity of the bullet is 341.64 m/s. Velocity of the bullet is 341.64 m/s.
To know more about bullet visit:
https://brainly.com/question/29231632
#SPJ11
a particle carrying a charge of 8.0nC accelerates through a potential of ∆V=-10mV. what is the change in potential energy of the particle?
The change in potential energy of the particle is calculated using the formula ∆PE = q∆V, where q is the charge of the particle and ∆V is the change in potential.
The potential energy (PE) of a charged particle in an electric field is given by the equation PE = qV, where q is the charge of the particle and V is the electric potential. In this case, the particle carries a charge of 8.0 nC (8.0 × 10⁻⁹ C) and accelerates through a potential difference (∆V) of -10 mV (-10 × 10⁻³ V).
To calculate the change in potential energy (∆PE), we can use the formula ∆PE = q∆V. Substituting the given values, we have ∆PE = (8.0 × 10⁻⁹ C) × (-10 × 10⁻³ V). Simplifying the expression, we get ∆PE = -8.0 × 10⁻¹² J.
The negative sign in the result indicates that the change in potential energy is negative, implying a decrease in potential energy. This means that the particle loses potential energy as it accelerates through the given potential difference. The magnitude of the change in potential energy is 8.0 × 10⁻¹² J.
Learn more about potential energy visit:
brainly.com/question/24284560
#SPJ11