The solution to [tex]d²u/dx² + d²u/dy² + d²u/dz² = 0[/tex] can be derived by using the method of separation of variables. This method is used to solve partial differential equations that are linear and homogeneous.
To solve this equation, assume that u(x,y,z) can be written as the product of three functions:[tex]u(x,y,z) = X(x)Y(y)Z(z)[/tex].
Now substitute these partial derivatives into the original partial differential equation and divide through by [tex]X(x)Y(y)Z(z):\\X''(x)/X(x) + Y''(y)/Y(y) + Z''(z)/Z(z) = 0[/tex]
These are three ordinary differential equations that can be solved separately. The solutions are of the form:
[tex]X(x) = Asin(αx) + Bcos(αx)Y(y) = Csin(βy) + Dcos(βy)Z(z) = Esin(γz) + Fcos(γz)[/tex]
where α, β, and γ are constants that depend on the value of λ. The constants A, B, C, D, E, and F are constants of integration.
Finally, the solution to the partial differential equation is:[tex]u(x,y,z) = ΣΣΣ [Asin(αx) + Bcos(αx)][Csin(βy) + Dcos(βy)][Esin(γz) + Fcos(γz)][/tex]
where Σ denotes the sum over all possible values of α, β, and γ.
This solution is valid as long as the constants α, β, and γ satisfy the condition:[tex]α² + β² + γ² = λ[/tex]
where λ is the constant that was introduced earlier.
To know more about separation visit:
https://brainly.com/question/16774902
#SPJ11
The general solution for the Laplace equation is the product of these three solutions: [tex]\(u(x, y, z) = (A_1\sin(\lambda x) + A_2\cos(\lambda x))(B_1\sin(\lambda y) + B_2\cos(\lambda y))(C_1\sin(\lambda z) + C_2\cos(\lambda z))\)[/tex] where [tex]\(\lambda\)[/tex] can take any non-zero value.
The given equation is a second-order homogeneous partial differential equation known as the Laplace equation. It can be written as:
[tex]\(\frac{{d^2u}}{{dx^2}} + \frac{{d^2u}}{{dy^2}} + \frac{{d^2u}}{{dz^2}} = 0\)[/tex]
To find the solution, we can use the method of separation of variables. We assume that the solution can be expressed as a product of three functions, each depending on only one of the variables x, y, and z:
[tex]\(u(x, y, z) = X(x)Y(y)Z(z)\)[/tex]
Substituting this into the equation, we have:
[tex]\(X''(x)Y(y)Z(z) + X(x)Y''(y)Z(z) + X(x)Y(y)Z''(z) = 0\)[/tex]
Dividing through by [tex]\(X(x)Y(y)Z(z)\)[/tex], we get:
[tex]\(\frac{{X''(x)}}{{X(x)}} + \frac{{Y''(y)}}{{Y(y)}} + \frac{{Z''(z)}}{{Z(z)}} = 0\)[/tex]
Since each term in the equation depends only on one variable, they must be constant. Denoting this constant as -λ², we have:
[tex]\(\frac{{X''(x)}}{{X(x)}} = -\lambda^2\)\\\(\frac{{Y''(y)}}{{Y(y)}} = -\lambda^2\)\\\(\frac{{Z''(z)}}{{Z(z)}} = -\lambda^2\)[/tex]
Now, we have three ordinary differential equations to solve:
[tex]1. \(X''(x) + \lambda^2X(x) = 0\)\\2. \(Y''(y) + \lambda^2Y(y) = 0\)\\3. \(Z''(z) + \lambda^2Z(z) = 0\)[/tex]
Each of these equations is a second-order ordinary differential equation. The general solution for each equation can be written as a linear combination of sine and cosine functions:
[tex]1. \(X(x) = A_1\sin(\lambda x) + A_2\cos(\lambda x)\)\\2. \(Y(y) = B_1\sin(\lambda y) + B_2\cos(\lambda y)\)\\3. \(Z(z) = C_1\sin(\lambda z) + C_2\cos(\lambda z)\)[/tex]
Learn more about Laplace
https://brainly.com/question/32625911
#SPJ11
4. Solve the difference equation using Z-transforms Yn+3 - 3yn+12yn = 3", yo = 2, ₁ = 1, y2 = 6.
We have to solve this equation using the Z-transform, we follow the following steps:
Step 1: Apply the Z-transform to the given difference equation, resulting in:
[tex]Z{Yn+2} - Z{yn} = 3/(1 - 3Z⁻¹ + 12Z⁻²)[/tex]
Step 2: Multiply the Z-transform of Yn by Z³ and subtract it from the Z-transform of Yn+3, resulting in:
[tex]Z³{Yn+3} - Z³{yn} = 3Z³{Yn+2}[/tex]
Step 3: Multiply the Z-transform of Yn+1 by Z and subtract it from the Z-transform of Yn+2, resulting in:
[tex]Z²{Yn+2} - Z{Yn+1} = Z²{Yn+1}[/tex]
Step 4: Simplify the equation to obtain:
[tex]Z²{Yn+2} = Z²{Yn+1} + Z{Yn+1} + 3Z⁻¹{Yn} - 12Z⁻²{Yn-1}[/tex]
Step 5: Substitute the values of Yo, Y1, and Y2 in the equation to find [tex]Z²{Y3}[/tex], which results in:
[tex]Z²{Y3} = 7 + 6Z⁻¹ - 12Z⁻²[/tex]
Step 6: Using the equation[tex]Z²{Yn+2} = Z²{Yn+1} + Z{Yn+1} + 3Z⁻¹{Yn} - 12Z⁻²{Yn-1}[/tex], substitute Z²{Y3} and simplify to find Z²{Y4}, which results in:
[tex]Z²{Y4} = 13 + 6Z⁻¹ - 6Z⁻²[/tex]
Step 7: Apply the inverse Z-transform to Z²{Y4} to obtain the final solution, which is:
Y4 = 13δn - 6n + 6(1/2)ⁿ
Therefore, the solution of the difference equation using Z-transforms is Y4 = 13δn - 6n + 6(1/2)ⁿ.
To know more about Z-transform visit:
https://brainly.com/question/11709244
#SPJ11
. Which of the following is true of a Euler circuit?
it cannot have any odd vertices
I cannot have any even vertices
can have at most 2 odd vertices
It can have only one odd vertex
If it has more than 2 odd vertices, a Euler circuit cannot be formed.
A Euler circuit is a path in a graph that visits every edge exactly once and returns to the starting point.
It is important to note that a Euler circuit can only exist in certain types of graphs.
Out of the given options, the correct statement about a Euler circuit is: "It can have at most 2 odd vertices."
An odd vertex is a vertex with an odd number of edges connected to it. In a graph, a Euler circuit can have at most 2 odd vertices.
If a Euler circuit has 0 odd vertices, it is called a Eulerian circuit.
If it has 2 odd vertices, it is called a semi-Eulerian circuit.
For example, let's consider a graph with 6 vertices and 9 edges.
If this graph has exactly 2 odd vertices, it can have a Euler circuit.
However, if it has more than 2 odd vertices, a Euler circuit cannot be formed.
Learn more about Euler circuit from this link:
https://brainly.com/question/29555996
#SPJ11
how
to solve each step
26. The mass of an iron-56 nucleus is 55.92066 units. a. What is the mass defect of this nucleus? b. What is the binding energy of the nucleus? c. Find the binding energy per nucleon.
a. The mass defect of an iron-56 nucleus is 0.04334 units.
b. The binding energy of the nucleus is 492.52 MeV.
c. The binding energy per nucleon is 8.804 MeV.
The mass defect of an iron-56 nucleus is 0.04334 units. The mass defect is the difference between the mass of the nucleus and the sum of the masses of its individual protons and neutrons. It represents the mass that is converted into energy during the formation of the nucleus.
The binding energy of the nucleus is 492.52 MeV. The binding energy is the energy required to completely separate the nucleons (protons and neutrons) in the nucleus. It is a measure of the stability of the nucleus. The binding energy is equivalent to the mass defect of the nucleus multiplied by the speed of light squared (E = mc^2).
The binding energy per nucleon is 8.804 MeV. It is calculated by dividing the total binding energy of the nucleus by the number of nucleons in the nucleus. The binding energy per nucleon is a measure of the average amount of energy required to remove a nucleon from the nucleus. It is often used to compare the stability of different nuclei, with higher values indicating greater stability.
Know more about nucleus here:
https://brainly.com/question/23366064
#SPJ11
Analia is a school district manager. Here are some details about two schools in her district. Analia wants to know which school has higher athletic achievement relative to the budget per student. Determine which school has higher athletic achievement relative to the budget per student, according to the two definitions. Did you get the same result for both definitions?
Answer:
The given information does not provide numerical data to compare the two schools' budget per student and athletic achievement. Therefore, it is not possible to determine which school has a higher athletic achievement relative to the budget per student
Step-by-step explanation:
Suppose you are givin the following information and the coordinate plane below
Need asap
The distance between points A(2, 4) and B(4, 6) is approximately
2.83 units.How to find the distanceThe distance formula states that the distance between two points (x₁, y₁) and (x₂, y₂) in a two-dimensional plane is given by:
d = √((x₂ - x₁)² + (y₂ - y₁)²)
Let's apply the formula to calculate the distance between A and B:
d = √((4 - 2)² + (6 - 4)²)
= √(2² + 2²)
= √(4 + 4)
= √8
≈ 2.83
Learn more about line segment at
https://brainly.com/question/17374569
#SPJ1
A. A plant treats an ore containing Pyrite (FeS2), Arsenopyrite (FeAss) and chalcopyrite (CuFeS2). After ore upgrading and analysis, the Arsenic (As), Copper (Cu) and Iron (Fe) concentration in the concentrate were 9.6%, 13.5% and 63.3% respectively. What is the concentration of pyrite, arsenopyrite, chalcopyrite in the concentrate? (Molar masses of As, Cu, Fe and Sare 74.92 g/mol, 63.55 g/mol, 55.85 g/mol and 32.07 g/mol respectively). (15 marks) B. 150 tph of material is subjected screening to separate the oversize from the undersize materials. If the cut-point size for the feed, oversize and undersize are 0.3, 0.85 and 0.15 respectively, calculate the recovery of oversize and undersize materials. Also determine the overall screen efficiency. (15 marks) C. Calculate how many kg of magnetite must be added to 1L of water to make a slurry with a pulp density of 1.9 g/cm3. Assume density of magnetite is 5.2g/cm3
A. The concentration of pyrite, arsenopyrite, and chalcopyrite in the concentrate is:
- Pyrite (FeS2): 2.268 mol
- Arsenopyrite (FeAsS): 0.128 mol
- Chalcopyrite (CuFeS2): 0.212 mol
B. The recovery of oversize materials is 80%, the recovery of undersize materials is 20%, and the overall screen efficiency is 100%.
C. Approximately 0.9 grams of magnetite must be added to 1 L of water to make a slurry with a pulp density of 1.9 g/cm3.
A. To find the concentration of pyrite, arsenopyrite, and chalcopyrite in the concentrate, we need to calculate the amount of each mineral present based on their respective concentrations of arsenic (As), copper (Cu), and iron (Fe).
First, let's assume we have 100 grams of the concentrate. From the given concentrations, we can calculate the weight of each element in the concentrate as follows:
- Arsenic (As): 9.6% of 100 g = 9.6 g
- Copper (Cu): 13.5% of 100 g = 13.5 g
- Iron (Fe): 63.3% of 100 g = 63.3 g
Now, we need to convert the weight of each element to moles by dividing it by its molar mass:
- Arsenic (As): 9.6 g / 74.92 g/mol = 0.128 mol
- Copper (Cu): 13.5 g / 63.55 g/mol = 0.212 mol
- Iron (Fe): 63.3 g / 55.85 g/mol = 1.134 mol
Since pyrite (FeS2) contains 2 moles of iron (Fe) for every 1 mole of sulfur (S), the concentration of pyrite can be calculated as:
- Pyrite (FeS2): 2 * 1.134 mol = 2.268 mol
Similarly, arsenopyrite (FeAsS) contains 1 mole of arsenic (As), 1 mole of iron (Fe), and 1 mole of sulfur (S), so the concentration of arsenopyrite can be calculated as:
- Arsenopyrite (FeAsS): 0.128 mol
Chalcopyrite (CuFeS2) contains 1 mole of copper (Cu), 1 mole of iron (Fe), and 2 moles of sulfur (S), so the concentration of chalcopyrite can be calculated as:
- Chalcopyrite (CuFeS2): 0.212 mol
Therefore, the concentration of pyrite, arsenopyrite, and chalcopyrite in the concentrate is:
- Pyrite (FeS2): 2.268 mol
- Arsenopyrite (FeAsS): 0.128 mol
- Chalcopyrite (CuFeS2): 0.212 mol
B. To calculate the recovery of oversize and undersize materials, as well as the overall screen efficiency, we need to consider the feed, oversize, and undersize materials' cut-point sizes.
The recovery of oversize materials is the percentage of material larger than the cut-point size that passes through the screen. In this case, the cut-point size for oversize is 0.85. If the oversize material passing through the screen is 120 tph, we can calculate the recovery as:
- Recovery of oversize = (120 tph / 150 tph) * 100 = 80%
The recovery of undersize materials is the percentage of material smaller than the cut-point size that passes through the screen. In this case, the cut-point size for undersize is 0.15. If the undersize material passing through the screen is 30 tph, we can calculate the recovery as:
- Recovery of undersize = (30 tph / 150 tph) * 100 = 20%
The overall screen efficiency is the percentage of material passing through the screen compared to the total feed. If the total feed is 150 tph and the material passing through the screen is 150 tph, we can calculate the overall screen efficiency as:
- Overall screen efficiency = (150 tph / 150 tph) * 100 = 100%
C. To calculate the amount of magnetite required to make a slurry with a pulp density of 1.9 g/cm3, we need to use the density of magnetite and the volume of water.
Given:
- Density of magnetite = 5.2 g/cm3
- Pulp density = 1.9 g/cm3
- Volume of water = 1 L
First, we need to determine the mass of water by multiplying the volume by its density:
- Mass of water = Volume of water * Density of water = 1 L * 1 g/cm3 = 1000 g
Now, let's assume we need x grams of magnetite. The total mass of the slurry will be the sum of the mass of water and the mass of magnetite:
- Total mass of slurry = Mass of water + Mass of magnetite = 1000 g + x g
Since the pulp density is given as 1.9 g/cm3, the volume of the slurry can be calculated as the total mass of the slurry divided by the pulp density:
- Volume of slurry = Total mass of slurry / Pulp density = (1000 g + x g) / 1.9 g/cm3
Since the volume of slurry is given as 1 L, we can equate the volume equation to 1 L and solve for x:
- (1000 g + x g) / 1.9 g/cm3 = 1 L
- 1000 g + x g = 1.9 g/cm3 * 1 L
- x g = 1.9 g/cm3 * 1 L - 1000 g
- x g = 1.9 g - 1000 g
- x g = 0.9 g
Therefore, approximately 0.9 grams of magnetite must be added to 1 L of water to make a slurry with a pulp density of 1.9 g/cm3.
In summary:
A. The concentration of pyrite, arsenopyrite, and chalcopyrite in the concentrate is:
- Pyrite (FeS2): 2.268 mol
- Arsenopyrite (FeAsS): 0.128 mol
- Chalcopyrite (CuFeS2): 0.212 mol
B. The recovery of oversize materials is 80%, the recovery of undersize materials is 20%, and the overall screen efficiency is 100%.
C. Approximately 0.9 grams of magnetite must be added to 1 L of water to make a slurry with a pulp density of 1.9 g/cm3.
Learn more about efficiency from given link: https://brainly.com/question/13222283
#SPJ11
What is A’P?
Need asap
Answer:
AP is 9 inch
Step-by-step explanation:
It says right there on paper
A vertical curve below has a lower point (A) which exists at station (53+50) with elevation (1271.2 m). the back grade of (-4%) meet the forward grade of (+3.8%) at (PVI) station (52+00) with elevation (1261.5 m). determine the length of the curve with the stations of (PVC) and (PVT)?
A vertical curve is a road with changing elevation over a distance. A crest curve has an increasing slope, while a sag curve has a decreasing slope. Calculating the elevation of PVC and PVT stations using the formula, we get a length of 275.70 m. The equations for PVC and PVT give us the desired length.
A vertical curve is a curve on a road where the elevation is changing over a certain distance. A curve with an increasing slope is referred to as a crest curve, while a curve with a decreasing slope is referred to as a sag curve. The problem has given us the following details:
Lets' calculate the Elevation of PVC:
PVC station lies before the PVI, and it is a point of intersection between the back grade and the vertical curve. Let's assume that the length of the vertical curve is (L).The elevation of PVC can be calculated as follows:
Elevation of PVC = Elevation of Lower Point + Vertical Distance of PVC from Lower Point
Elevation of PVC = 1271.2 m - [(-4/100)(53.5 m - 52.0 m)]
Elevation of PVC = 1271.2 m - (-0.54 m)
Elevation of PVC = 1271.74 m
Let's calculate the Elevation of PVT:PVT station lies after the PVI, and it is a point of intersection between the forward grade and the vertical curve. The elevation of PVT can be calculated as follows:
Elevation of PVT = Elevation of PVI + Vertical Distance of PVT from PVI
Here, the vertical distance between the PVI and PVT is unknown, but it can be calculated using the following formula: Vertical Distance between PVI and
PVT = L/2 * [(BG + FG)/(BG * FG)]
Vertical Distance between PVI and
PVT = L/2 * [(-4 + 3.8)/(-4 * 3.8)]
Vertical Distance between PVI and
PVT = L/2 * [-0.0658]
Vertical Distance between PVI and PVT = -0.0329 * L
Substitute the above value of the vertical distance between PVI and PVT in the formula for calculating the elevation of PVT:
Elevation of PVT = 1261.5 m + [-0.0329 * L]
Let's equate the elevations of PVC and PVT:
Elevation of PVC = Elevation of PVT1271.74 m
= 1261.5 m + [-0.0329 * L]
Solve for L to determine the length of the vertical curve:L = 275.70 m
Therefore, the length of the curve with the stations of (PVC) and (PVT) is 275.70 m.
To know more about Elevation of PVC Visit:
https://brainly.com/question/32891538
#SPJ11
I need full solution please
4m 3m с 3m A Determine the reactions at the supports and draw moment and shear diagrams by method slop-deflection equations. Assume El is constant. 5kn/m 30kn 3m B 10kn 3m
The reactions at the supports and the moment and shear diagrams can be determined using the slope-deflection equations method. The given structure consists of a 4m beam supported by two fixed supports at the ends, with a concentrated load of 30kN at 3m from support A, a distributed load of 5kN/m over the entire span, and a concentrated load of 10kN at 3m from support B. By applying the slope-deflection equations, we can calculate the reactions and draw the moment and shear diagrams.
The slope-deflection equations relate the moments and slopes at different points along a beam to the applied loads and properties of the beam.
Step 1: Calculate the reactions at the supports by taking moments about one of the supports. In this case, the reactions at the supports will be equal due to symmetry.Step 2: Calculate the slope at the ends of the beam. The slope at each end is assumed to be zero due to the fixed supports.Step 3: Apply the slope-deflection equations to find the moments at different points along the beam.Step 4: Draw the moment diagram by plotting the calculated moments along the beam's length. The moment diagram will consist of straight lines with breaks at the locations of concentrated loads.Step 5: Calculate the shear forces at different points along the beam using the equilibrium equations.Step 6: Draw the shear diagram by plotting the calculated shear forces along the beam's length. The shear diagram will also have breaks at the locations of concentrated loads.Step 7: Analyze the moment and shear diagrams to determine the maximum bending moment and maximum shear force, which are crucial for designing the beam.By applying the slope-deflection equations method, we can determine the reactions at the supports and draw the moment and shear diagrams for the given structure. These diagrams provide valuable information about the internal forces and moments in the beam, aiding in structural analysis and design.
Learn more about slope-deflection :
https://brainly.com/question/32165223
#SPJ11
Given the exponential model a ∙ bx = (72.3)(1.001)x for an estimated life expectancy in years for an African American, estimate the number of years the average African American will live if they are born in the year 2012. Recall that the variable x from the exponential model represents the number of years after 2002.
The estimate for the number of years the average African American will live if born in 2012 is[tex](72.3)(1.001)^{10.[/tex]
To estimate the number of years the average African American will live if they are born in the year 2012, we need to determine the value of x for that particular year.
Since x represents the number of years after 2002, to calculate x for 2012, we subtract 2002 from 2012:
x = 2012 - 2002 = 10
Now we can use the exponential model:
a ∙ bx = (72.3)(1.001)x
Plugging in the value of x, we have:
a ∙ b^10 = (72.3)(1.001)^10
We do not have the specific values of a and b, so we cannot calculate the exact estimate. However, we can provide the expression as the estimate for the number of years the average African American will live if born in 2012:
(72.3)(1.001)^10
Evaluating this expression using a calculator will give an estimated value.
Please note that this is an estimate based on the given exponential model.
To obtain more accurate and up-to-date life expectancy estimates for African Americans, it is advisable to refer to reliable sources or statistical data specific to the relevant year.
For more question on average visit:
https://brainly.com/question/130657
#SPJ8
In a scaled-down trial of a planned dam, a rectangular weir design is analysed to determine its suitability for the given application. The main data obtained from the rectangular weir design trial was as follows: width of the weir was 0.03 m; height of the water level was 0.01 m; volumetric flow rate was 5.33 × 10-5 m3/s; and, volume of water collected was 0.0003 m3. Determine what the Coefficient of Discharge, Cd, of the flow was for these values.
The Coefficient of Discharge (Cd) for the given rectangular weir design trial is approximately 4.03
The Coefficient of Discharge (Cd) measures the efficiency of a rectangular weir design in allowing water to flow through it. To determine the Cd, we can use the given data:
- Width of the weir (w) = 0.03 m
- Height of the water level (h) = 0.01 m
- Volumetric flow rate (Q) = 5.33 × 10-5 m3/s
- Volume of water collected (V) = 0.0003 m3
The formula to calculate the Cd is:
Cd = Q / (w * h * sqrt(2 * g * h))
where g is the acceleration due to gravity (approximately 9.8 m/s2).
First, we need to calculate the value of Q / (w * h * sqrt(2 * g * h)).
Substituting the given values:
Q / (w * h * sqrt(2 * g * h)) = (5.33 × 10-5 m3/s) / (0.03 m * 0.01 m * sqrt(2 * 9.8 m/s2 * 0.01 m))
Simplifying the equation inside the square root:
Q / (w * h * sqrt(2 * g * h)) = (5.33 × 10-5 m3/s) / (0.03 m * 0.01 m * sqrt(0.196 m2/s2))
Calculating the square root:
Q / (w * h * sqrt(2 * g * h)) = (5.33 × 10-5 m3/s) / (0.03 m * 0.01 m * 0.442 m/s)
Simplifying the denominator:
Q / (w * h * sqrt(2 * g * h)) = (5.33 × 10-5 m3/s) / (0.00001326 m4/s)
Finally, calculating the Cd:
Cd = (5.33 × 10-5 m3/s) / (0.00001326 m4/s)
Cd ≈ 4.03
Therefore, the Coefficient of Discharge (Cd) for the given rectangular weir design trial is approximately 4.03.
Learn more about flow rate from the link:
https://brainly.com/question/31070366
#SPJ11
Solve the following compound inequality: x greater-than-or-equal-to negative 1 or x less-than 2. a. Negative 1 less-than-or-equal-to x less-than 2 c. x greater-than-or-equal-to negative 1 b. no solution d. all real numbers Please select the best answer from the choices provided A B C D
Combining the two sets of values, we find that the overlapping solution is: -1 ≤ x < 2. Option A is the correct answer.
The compound inequality given is: x ≥ -1 or x < 2.
To solve this compound inequality, we can break it down into two separate inequalities and then find the overlapping solution.
First inequality: x ≥ -1
This inequality represents all the values of x that are greater than or equal to -1.
Second inequality: x < 2
This inequality represents all the values of x that are less than 2.
To find the overlapping solution, we need to determine the values that satisfy both inequalities.
From the first inequality, x ≥ -1, we know that x can take any value that is greater than or equal to -1.
From the second inequality, x < 2, we know that x can take any value that is strictly less than 2.
Combining these two sets of values, we find that the overlapping solution is:
-1 ≤ x < 2
For such more question on overlapping:
https://brainly.com/question/10711016
#SPJ8
100 POINT!!!!!!! PLEASE HELP ME WITH THIS QUICLKY.
Answer:
1) AB ~ EF, BC ~ FG, CD ~ GH, AD ~ EH
2) Angle A is congruent to angle E.
Angle B is congruent to angle F.
Angle C is congruent to angle G.
Angle D is congruent to angle H.
3) AD = BC = 8, CD = (2/3)(6) = 4, so
AB = 3(4) = 12, EF = (3/2)(12) = 18,
EH = FG = (2/3)(8) = 12
Perimeter of ABCD = 12 + 8 + 8 + 4
= 32 cm
Perimeter of EFGH = 18 + 12 + 12 + 6
= 48 cm
A city has a sewage treatment plant with a capacity of 100 MGD. The rate of input to the plant is 200 gallons per day per person. The present population of the city is 400,000 and is 5Y,000 more than its population 10 years ago. Assuming a linear growth, the existing plant would be adequate for how many more years (to the nearest year). Adequate for _______ more years
Hence, the plant will be adequate for 10 more years (to the nearest year).
Given, Rate of input to the plant = 200 gallons per day per person
Population of the city = 400,000
Let the population of the city 10 years ago be x gallons per day per person
Then, population of the city 5 years ago = x+ (400000-5000)
= x+ 395000
Thus, rate of input to the plant 10 years ago = 200x gallons per day
After 10 years, population will increase by 5000 and become 405000 people.
Therefore, rate of input to the plant after 10 years = 405000 × 200
= 81,000,000 gallons per day
Now, the plant with capacity of 100 MGD = 100×1000×365×24 gallons per year
= 876,000,000 gallons per year
Thus, the present plant would be adequate for = 876,000,000 ÷ 81,000,000
= 10.81 years
To know more about gallons visit:
https://brainly.com/question/31702678
#SPJ11
What is the density of a certain liquid whose specific weight is 99.6 lb/ft3? Express your answer in g/cm³. 2. A moving plate is 15mm from a fixed plate. If the moving plate requires a force per unit area of 15 Pa to maintain a speed of 0.70 m/s, determine the viscosity of the substance between the two plates.
Density of a certain liquid:Specific weight is also called the weight density of a liquid and it's given as .Therefore, the viscosity of the substance between the two plates is 0.32 Pa.s.
w = ρgwhere
w = weight density,
ρ = density of the liquid,
g = acceleration due to gravity.
Now, we can express the density of the liquid as;
ρ = w/g = 99.6 lb/ft³ / 32.2 ft/s²
= 3.1 kg/m³
Now, we can convert the density from kg/m³ to g/cm³ as follows;
ρ = 3.1 kg/m³ x 1000 g/kg / (100 cm/m)³
= 0.0031 g/cm³
Therefore, the density of the certain liquid is 0.0031 g/cm³2. Viscosity of the substance between two plates:We can find the viscosity of the substance between the two plates by using the formula;
F/A = μv/dwhere F/A is the shear stress,
μ is the viscosity of the substance,
v is the velocity of the moving plate,
d is the distance between the plates. Substituting the values given into the formula, we have;
15 Pa = μ(0.70 m/s) / 0.015 mμ
= 15 Pa x 0.015 m / 0.70 m/sμ
= 0.32 Pa.s
To know more about weight visit:
https://brainly.com/question/28532216
#SPJ11
Attempt to write the dehydration reaction of ethyl alcohol using H_2SO_4 as a catalyst at 180 °C ---
The dehydration reaction of ethyl alcohol using H2SO4 as a catalyst at 180 °C results in the formation of ethylene gas and water.
Dehydration is a chemical reaction that involves the removal of water molecules from a compound. In this case, when ethyl alcohol (C2H5OH) is subjected to the influence of H2SO4 (sulfuric acid) as a catalyst at a high temperature of 180 °C, the hydroxyl group (-OH) of ethyl alcohol reacts with the acid to form a water molecule (H2O). This process of water elimination from the alcohol molecule is commonly known as dehydration.
The reaction can be represented by the following chemical equation:
C2H5OH + H2SO4 → C2H4 + H2O
As a result of this reaction, ethyl alcohol undergoes dehydrogenation, where it loses a hydrogen atom along with the hydroxyl group to form ethylene gas (C2H4). Ethylene is an unsaturated hydrocarbon and is commonly used in various industries, including the production of plastics, solvents, and synthetic fibers.
The presence of H2SO4 as a catalyst accelerates the rate of the reaction by providing an alternative reaction pathway with lower activation energy. The catalyst facilitates the breaking of the C-O bond in the alcohol, allowing for the formation of the ethylene molecule. The sulfuric acid does not undergo any permanent change during the reaction and can be reused.
Learn more about Dehydration
brainly.com/question/28428859
#SPJ11
. Answer the following questions of MBR. a) What is the membrane pore size typically used in the Membrane bioreactor for wastewater treatment? b) What type of filtration is typically used for desalination? c) what are the two MBR configurations? which one is used more widely? d) list three membrane fouling mechanisms. e) when comparing with conventional activated sludge treatment process, list three advantages of using an MBR
Advantages of MBR: Improved effluent quality, smaller footprint, better process control.
What is the typical membrane pore size used in MBR for wastewater treatment?The two MBR configurations commonly used are submerged and side-stream. In the submerged configuration, the membrane modules are fully immersed in the bioreactor, and the wastewater flows through the membranes.
This configuration offers advantages such as simplicity of design, easy maintenance, and efficient aeration. On the other hand, the side-stream configuration involves diverting a portion of the mixed liquor from the bioreactor to an external membrane tank for filtration. This configuration allows for higher biomass concentrations and longer sludge retention times, which can enhance nutrient removal. However, it requires additional pumping and may have a larger footprint.
The submerged configuration is used more widely in MBR applications due to its operational simplicity and smaller footprint compared to the side-stream configuration.
The submerged membranes offer easy access for maintenance and cleaning, and they can be integrated into existing activated sludge systems with minimal modifications.
Learn more about MBR
brainly.com/question/32370913
#SPJ11
When the following equation is balanced properly under acidic conditions, what are the coefficients of the species shown? _____Cr^3+ + _______Br^-_______Cr^2+ + _______BrO_3- .Water appears in the balanced equation as a __________(reactant, product, neither) with a coefficient of ___________ (Enter 0 for neither.)Which element is oxidized? _________
Water appears as a product with a coefficient of 2.
The balanced equation for the given reaction under acidic conditions is as follows:
4H^+ + 3Cr^3+ + 3Br^- -> 3Cr^2+ + BrO_3^- + 2H_2O
In this balanced equation, the coefficients of the species are:
- 3 for Cr^3+
- 3 for Br^-
- 3 for Cr^2+
- 1 for BrO_3^-
Water appears in the balanced equation as a product with a coefficient of 2.
To determine which element is oxidized, we need to look at the change in oxidation states. In this equation, Cr goes from an oxidation state of +3 to +2, which means it has gained electrons and is being reduced. Therefore, the element that is oxidized in this reaction is Br.
In summary, the coefficients of the species in the balanced equation are:
- Cr^3+: 3
- Br^-: 3
- Cr^2+: 3
- BrO_3^-: 1
Water appears as a product with a coefficient of 2.
The element that is oxidized in this reaction is Br.
learn more about coefficient on :
https://brainly.com/question/1038771
#SPJ11
The Hayflick limit is the limit telomeres can be shorten. Please explain and provide detail on how/why telomeres get shorten? Are telomeres able to be recreated? If so how and where would we find this?
Telomeres, which protect chromosome ends, shorten with each cell division due to the limitations of DNA replication, but can be partially replenished by telomerase in certain cell types, while their length and telomerase activity have implications for aging and disease.
The Hayflick limit refers to the maximum number of times a normal human cell can divide before reaching a state of replicative senescence or cell death. It was discovered by Leonard Hayflick in the 1960s and is associated with the shortening of telomeres.
Telomeres are repetitive DNA sequences located at the ends of chromosomes. Their primary function is to protect the genetic material of the chromosome from degradation and prevent the loss of essential genes during DNA replication. However, with each cell division, the telomeres progressively shorten.
Telomere shortening occurs due to the inherent limitations of DNA replication. The DNA replication machinery is unable to fully replicate the very ends of linear chromosomes, leading to the loss of a small portion of telomeric DNA with each round of cell division. This process is known as the "end replication problem."
To know more about Telomeres,
https://brainly.com/question/14131705
#SPJ11
Algebra I-A
2 84.3 Quiz: Two-Variable Systems of treuses
A. Region D
B. Region A
C. Region C
OD. Region B
A
D
B
The region of the solutions to the system is (d) Region B
Selecting the region of the solutions to the systemFrom the question, we have the following parameters that can be used in our computation:
The graph
This point of intersection of the lines of the graph represent the solution to the system graphed
From the graph, we have the intersection point to be
(x, y) = (2, 3)
This is located in region B and it means that
x = 2 and y = 3
Hence, the region of the solutions to the system is (d) Region B
Read more about equations at
brainly.com/question/148035
#SPJ1
Armed with the knowledge that full compaction of a segregated concrete mix is impossible, outline the importance of maintaining a heterogeneous mixture with uniform distribution of the mixture constituents.
It is essential to maintain a heterogeneous mixture with uniform distribution of the mixture constituents since full compaction of a segregated concrete mix is impossible. The concrete mix is created by mixing cement, sand, water, and aggregates.
The constituents of concrete mix have different sizes, shapes, densities, and water absorption properties.As a result, they segregate due to gravity during the mixing and transportation process. The denser materials such as coarse aggregate sink to the bottom while the lighter ones such as cement tend to float to the top. This segregation leads to an uneven distribution of materials in the mixture.
As a result, during the pouring of the concrete, there is a probability of unevenness in the density of the final product.This will lead to various problems, for instance, the creation of cracks in the concrete, or weakening the structure and ultimately resulting in an unsafe and unusable product.
Therefore, it is vital to maintain a uniform distribution of the mixture constituents in the concrete mix. This is achievable by controlling the mixing process and ensuring that the concrete mix remains in a plastic state during transportation, placement, and compaction.
The homogeneous mixture provides a uniform consistency and density throughout the mixture. It results in a high-quality product that has consistent strength, durability, and resistance to cracking.
In conclusion, a heterogeneous mixture with a uniform distribution of mixture constituents is essential in ensuring the quality of the final product. In the construction industry, the quality of concrete is of utmost importance since it affects the strength and durability of the structure. It is important to achieve a homogeneous mixture to ensure the quality and strength of the final product.
To know more about uniform distribution visit:
brainly.com/question/30639872
#SPJ11
An unbalanced vertical force of 270N upward accelerates a volume of 0.044 m³ of water. If the water is 0.90m deep in a cylindrical tank,
a. What is the acceleration of the tank?
b. What is the pressure at the bottom of the tank in kPa?
The main answer to part a of your question is that the acceleration of the tank can be calculated using Newton's second law of motion. The formula for acceleration is given by force divided by mass. In this case, the force is 270N and the mass of the water can be calculated by multiplying the density of water (1000 kg/m³) by its volume (0.044 m³). The resulting mass is 44 kg. Therefore, the acceleration of the tank is 270N divided by 44 kg, which is approximately 6.14 m/s².
To calculate the pressure at the bottom of the tank in kPa (kilopascals), we can use the equation for pressure, which is given by force divided by area. The force acting on the bottom of the tank is the weight of the water, which can be calculated by multiplying the mass of the water (44 kg) by the acceleration due to gravity (9.8 m/s²). This gives a force of 431.2 N. The area of the bottom of the cylindrical tank can be calculated using the formula for the area of a circle, which is π multiplied by the radius of the tank squared. Since the depth of the water is given as 0.90 m, we can use this value as the radius. Therefore, the area is π times 0.90 squared, which is approximately 2.54 m². Dividing the force by the area gives a pressure of approximately 169.68 kPa at the bottom of the tank.
To find the acceleration of the tank, we use Newton's second law of motion, which states that force is equal to mass times acceleration (F = ma). In this case, the force is given as 270N and the mass can be calculated by multiplying the density of water (1000 kg/m³) by its volume (0.044 m³). Dividing the force by the mass gives the acceleration.
To calculate the pressure at the bottom of the tank, we use the formula for pressure, which is force divided by area (P = F/A). The force acting on the bottom of the tank is the weight of the water, which can be calculated by multiplying the mass of the water by the acceleration due to gravity (9.8 m/s²). The area of the bottom of the tank can be calculated using the formula for the area of a circle, which is π times the radius squared. Dividing the force by the area gives the pressure in kPa.
TO know more about Newton's second law of motion , https://brainly.com/app/ask?q=Newton%27s+second+law+of+motion
#SPJ11
The acceleration of the tank is approximately 6.14 m/s², and the pressure at the bottom of the tank is approximately 303.7 kPa.
a. The acceleration of the tank can be determined using Newton's second law, which states that force is equal to mass multiplied by acceleration (F = ma). In this case, the unbalanced vertical force acting on the water is 270N upward. To find the acceleration, we need to calculate the mass of the water. The density of water is approximately 1000 kg/m³. Given that the volume of water is 0.044 m³, the mass can be calculated as follows:
mass = density × volume
mass = 1000 kg/m³ × 0.044 m³
mass = 44 kg.
Now we can use Newton's second law to find the acceleration:
acceleration = force / mass
acceleration = 270N / 44 kg
acceleration ≈ 6.14 m/s².
b. The pressure at the bottom of the tank can be determined using the formula for pressure:
pressure = force / area.
The force acting on the bottom of the tank is the weight of the water above it, which is equal to the mass of the water multiplied by the acceleration due to gravity (9.8 m/s²). The area of the bottom of the tank can be calculated using the formula for the area of a circle:
area = πr²,
where r is the radius of the tank. Since the tank is cylindrical, the radius is half of the diameter, which is given as 0.90m. Therefore, the radius is 0.45m. Now we can calculate the pressure:
pressure = (mass × acceleration due to gravity) / area
pressure = (44 kg × 9.8 m/s²) / (π × 0.45m)²
pressure ≈ 303.7 kPa.
To learn more about acceleration refer:
https://brainly.com/question/11167329
#SPJ11
Zara and H&M Through channel differentiati ntiation differentiate on channel's coverage, expertise, performance, e Through people differentiation - differentiate on firm's people or employees (friendly, helpful, better trained, etc...) Through image differentiation - differentiate on company's brand image (including reputation and history
Zara and H&M differentiate themselves through their channel coverage, expertise, employee quality, and brand image. Zara stands out with its extensive global presence, supply chain efficiency, friendly staff, and reputation for fast fashion. H&M, on the other hand, emphasizes affordability, sustainability, well-trained employees, and a commitment to ethical fashion. These differentiating factors contribute to their unique positions in the fashion industry.
Zara and H&M differentiate themselves through various aspects of their channels, people, and brand image. In terms of channel differentiation, Zara and H&M differ in their coverage and expertise. Zara has a wide global presence with numerous stores in prime locations, offering a convenient shopping experience for customers. They also excel in their supply chain management, allowing them to quickly respond to fashion trends and deliver new products to stores. On the other hand, H&M has an extensive network of stores as well but focuses on a broader customer base with more affordable fashion options.
Through people differentiation, both Zara and H&M strive to provide excellent customer service. Zara's employees are known for their friendly and helpful attitude, creating a positive shopping experience. H&M also invests in employee training to ensure their staff is knowledgeable and can assist customers effectively.
Regarding image differentiation, Zara and H&M have distinct brand images. Zara is known for its fast-fashion concept, offering trendy and up-to-date designs. They have built a reputation for innovation and quick turnaround times. H&M, on the other hand, focuses on sustainability and ethical practices, emphasizing their commitment to responsible fashion.
Learn more about brand image
https://brainly.com/question/12495783
#SPJ11
In this problem, p is in dollars and x is the number of units. The demand function for a product is p=100/ (x+4) If the equilibrium quantity is 6 units, what is the equilibrium price? P1= What is the equilibrium point? (x1,p1)=() What is the consumer's surplus? (Round your answer to the nearest cent.) $
The equilibrium price (p1) is $10.
The equilibrium point is (6, 10).
The consumer surplus, rounded to the nearest cent, is approximately $69.31.
Exp:
To find the equilibrium price and equilibrium point, we can set the quantity demanded equal to the quantity supplied.
The demand function is given by:
p = 100 / (x + 4)
At equilibrium, the quantity demanded (x) is equal to the equilibrium quantity (6 units).
Substituting x = 6 into the demand function, we can solve for the equilibrium price (p1):
p1 = 100 / (6 + 4)
p1 = 100 / 10
p1 = 10
Therefore, the equilibrium price (p1) is $10.
To find the equilibrium point (x1, p1), we substitute the equilibrium quantity and price into the demand function:
x1 = 6
p1 = 10
So, the equilibrium point is (6, 10).
Consumer surplus represents the additional benefit or value that consumers receive when they pay a price lower than what they are willing to pay.
It can be calculated by finding the area between the demand curve and the equilibrium price.
To calculate the consumer surplus, we first need to find the area under the demand curve up to the equilibrium quantity. The demand function is given by:
p = 100 / (x + 4)
Integrating the demand function with respect to x from 0 to 6 (equilibrium quantity), we can find the area:
CS = ∫[0 to 6] (100 / (x + 4)) dx
Evaluating the integral:
CS = [100 ln(x + 4)] from 0 to 6
CS = 100 ln(6 + 4) - 100 ln(0 + 4)
CS = 100 ln(10) - 100 ln(4)
Using a calculator, we can find the numerical value of the consumer surplus:
CS ≈ $69.31
Therefore, the consumer surplus, rounded to the nearest cent, is approximately $69.31.
Learn more about consumer surplus from the given link
https://brainly.com/question/13136036
#SPJ11
Use the standard electrochemical series given in your e-text to identify whether the following reactions would take place or not. If it takes place, please write the complete balanced reaction (starting with half reactions) and explain the reaction in your own words. a. Can Cd metal dissolve in HCl ? b. Can O_2 oxidize Fe^2⋅ to Fe^3+? c. Can Ni reduce Sn^2+? Will it reduce Co^2+ ? d. Is Cl_2gas a stronger oxidizing agent than O_2 gas? e. Can F_2 gas oxidize water?
a. Cd metal will not dissolve in HCl.
b. O₂ can oxidize Fe²⁺ to Fe³⁺.
c. Ni can reduce Sn²⁺ but cannot reduce Co²⁺.
d. Cl₂ gas is a stronger oxidizing agent than O₂ gas.
e. F₂ gas can oxidize water
To determine whether the given reactions would take place, we can use the standard electrochemical series. The electrochemical series ranks the elements and ions based on their tendency to undergo reduction or oxidation reactions. In general, a reaction will occur if the species being oxidized is higher in the series than the species being reduced.
a. Looking at the electrochemical series, we find that Cd is below hydrogen (H+) in the series. This means that Cd has a lower tendency to undergo oxidation compared to hydrogen. Therefore, Cd metal will not dissolve in HCl.
b. In the electrochemical series, O₂ is above Fe²⁺. This indicates that O₂ has a higher tendency to undergo reduction compared to Fe²⁺. Therefore, O₂ can oxidize Fe²⁺ to Fe³⁺. The balanced half-reactions and the overall reaction can be written as follows:
Half-reaction at the cathode (reduction): O₂ + 4H⁺ + 4e⁻ → 2H₂O
Half-reaction at the anode (oxidation): Fe²⁺ → Fe³⁺ + e⁻
Overall reaction: 2Fe²⁺ + O₂ + 4H⁺ → 2Fe³⁺ + 2H₂O
c. Referring to the electrochemical series, Ni is above Sn²⁺ but below Co²⁺. This means that Ni has a higher tendency to undergo reduction compared to Sn²⁺ but a lower tendency compared to Co²⁺. Therefore, Ni can reduce Sn²⁺ but cannot reduce Co²⁺.
d. Comparing Cl₂ and O₂ in the electrochemical series, we find that Cl₂ is higher than O₂. This indicates that Cl₂ has a higher tendency to undergo reduction compared to O₂. Therefore, Cl₂ gas is a stronger oxidizing agent than O₂ gas.
e. Looking at the electrochemical series, we see that F₂ is above O₂. This indicates that F₂ has a higher tendency to undergo reduction compared to O₂. Therefore, F₂ gas can oxidize water. The balanced half-reactions and the overall reaction can be written as follows:
Half-reaction at the cathode (reduction): F₂ + 2e⁻ → 2F⁻
Half-reaction at the anode (oxidation): 2H₂O → O₂ + 4H⁺ + 4e⁻
Overall reaction: F₂ + 2H₂O → 2F⁻ + O₂ + 4H⁺
Learn more about oxidation at https://brainly.com/question/31967581
#SPJ11
Cary bought albums totally $14.60, plus tax. If the sales tax is 5%, how much change should he get from two $10.00 bills? Select one: a. $4.77 b. $5.40 C. $4.67 d. $5.35 e. Not Here Triangle ABC is similar to triangle DEF. What is the value of x ? Select one: a. 6 m b. 18 m c. 15 m d. 12 m e. Not Here What is 7 and 1/8% expressed as a decimal? Select one: a. 7.8 b. Not Here c. 7.0125 d. 7.145 e. 7.18
To convert percentage to decimal we need to divide by 100, hence;
[tex]7.125 / 100 = 0.07125[/tex]
Answer: c. 7.0125
Hence, the requested answer for the question is: a. $4.67, b. 18 m, c. 7.0125
1. Calculation: Amount of sales tax = [tex]5/100 × $14.60 = $0.73[/tex]
Amount paid by Cary for the albums and the sales tax = [tex]$14.60 + $0.73[/tex]
= $15.33Amount paid by two $10 bills [tex]= 2 × $10.00 = $20.00[/tex]
Change Cary should get = Amount paid by the two $10 bills - Amount paid for the albums and the sales tax=[tex]$20.00 - $15.33 = $4.67[/tex]
Answer: C. $4.672. As we know that similar decimal have their corresponding angles congruent and their corresponding sides in proportion. So we can write down the following equation to find
x :ABC is similar to DEFAB/DE = AC/DF
Given AB = 6 meters, AC = 9 meters, and DE = 12 meters
Substituting values in the equation
[tex]AB/DE = AC/DF6/12 = 9/DFDF = 9 × 12/6 = 18[/tex]meters
Answer: b. 18 m3. 7 and 1/8% can be written in decimal form as follows:
7 and 1[tex]/8% = 7.125%[/tex]
To know more about decimal visit:
https://brainly.com/question/29765582
#SPJ11
Calculate the molecular mass and molar mass of CCI.
The formula "CCl" suggests that there are two carbon atoms (C) and one chlorine atom (Cl).
However, it is unclear whether the compound is supposed to have a double bond or not, as "CCI" does not correspond to a known molecule.
If we assume that "CCl" represents a molecule with a double bond between the two carbon atoms, the formula should be written as "C=C-Cl". In this case, the molecular mass can be calculated as follows:
[tex]Molecular mass = (2 * Atomic mass of carbon) + Atomic mass of chlorine[/tex]
Using the atomic masses of carbon and chlorine (rounded to two decimal places):
Atomic mass of carbon (C) = [tex]12.01 g/mol[/tex]
Atomic mass of chlorine (Cl) = [tex]35.45 g/mol[/tex]
[tex]Molecular mass = (2 * 12.01 g/mol) + 35.45 g/mol[/tex]
Molecular mass ≈ [tex]59.47 g/mol[/tex]
If "CCI" is intended to represent a different compound or arrangement, please provide more information or clarification to obtain an accurate calculation of the molecular mass and molar mass.
To know more about compound visit:
brainly.com/question/28205786
#SPJ11
h. W solve y′=2xyy2−x2
The solution to the differential equation is given by y = ±√[(4x^2 + 4C)/(y^2 - 2x^2)], where C is a constant.To solve the differential equation y′=2xyy2−x2, we can use the method of separation of variables.
1. Rewrite the equation in a more convenient form:
y′ = 2xy(y^2 - x^2)
2. Separate the variables by moving all the terms involving y to one side and all the terms involving x to the other side:
y(y^2 - x^2)dy = 2x dx
3. Integrate both sides with respect to their respective variables:
∫y(y^2 - x^2)dy = ∫2x dx
4. Evaluate the integrals:
∫y(y^2 - x^2)dy = y^4/4 - x^2y^2/2 + C1
∫2x dx = x^2 + C2
5. Set the two resulting expressions equal to each other:
y^4/4 - x^2y^2/2 + C1 = x^2 + C2
6. Rearrange the equation to isolate y:
y^4/4 - x^2y^2/2 = x^2 + C2 - C1
7. Combine the constants:
C = C2 - C1
8. Multiply through by 4 to eliminate fractions:
y^4 - 2x^2y^2 = 4x^2 + 4C
9. Factor out y^2:
y^2(y^2 - 2x^2) = 4x^2 + 4C
10. Solve for y^2:
y^2 = (4x^2 + 4C)/(y^2 - 2x^2)
11. Take the square root of both sides:
y = ±√[(4x^2 + 4C)/(y^2 - 2x^2)]
Learn more about differential equation from the link https://brainly.com/question/1164377
#SPJ11
A 1.8 m concrete pipe 125 mm thick carries water at a velocity of 2.75 m/s. The pipe line is 1250 m long and a valve is used to close the discharge end. Use E_B =2.2GPa and E_c =21GPa. What will be the maximum rise in pressure at the valve due to water hammer? A)2273kPa B)2575kPa C)1328kPa D)1987kPa
The maximum rise in pressure at the valve due to water hammer is 2273 kPa. Therefore, option A) 2273k Pa is the correct option.
Water hammer is a phenomenon that occurs in pipelines when the valve is suddenly closed, causing the pressure to rise and the flow to decelerate.
To calculate the maximum pressure rise at the valve due to water hammer, we can use the following formula:
ΔP = (ρ * v * L)/2 * [(E_B/E_c) * (t_o/t_i)^2 - 1]
where:
ΔP = maximum pressure rise
ρ = density of water = 1000 kg/m³
v = velocity of water = 2.75 m/s
L = length of pipeline = 1250 mt_
o = outer radius of pipe = 1.8 m/2 = 0.9 mt_
i = inner radius of pipe = 0.9 m - 0.125 m
= 0.775 m (assuming 125 mm thick pipe)
t_o/t_
i = (1.8/2)/(0.9 - 0.125) = 2.286
E_B = modulus of elasticity of concrete = 2.2 G
Pae_c = modulus of elasticity of water = 21 G
Plug in the values and simplify:
ΔP = (1000 * 2.75 * 1250)/2 * [(2.2/21) * (0.9/0.775)^2 - 1]
ΔP ≈ 2273 kPa
Therefore, the maximum rise in pressure at the valve due to water hammer is 2273 kPa. Therefore, option A) 2273k Pa is the correct option.
To know more about pressure visit:
https://brainly.com/question/30673967
#SPJ11
Select the correct answer.
Which statement is false?
A. The inequality sign always opens up to the larger number.
The greater number in an inequality is always above the other number on the vertical number line.
The smaller number in an inequality is always located to the left of the other number on the horizontal number line.
OD. The inequality sign always opens up to the smaller number.
B.
C.
Reset
Next