The equivalent resistance of the 180 Ω resistor and the 66 Ω resistor connected in parallel is approximately 48.2939 Ω.
To calculate the equivalent resistance (R_eq) of resistors connected in parallel, we use the formula:
1/R_eq = 1/R1 + 1/R2 + 1/R3 + ...
In this case, we have two resistors connected in parallel: a 180 Ω resistor (R1) and a 66 Ω resistor (R2). Plugging these values into the formula, we get:
1/R_eq = 1/180 Ω + 1/66 Ω
To simplify this equation, we find the common denominator and add the fractions:
1/R_eq = (66 + 180) / (180 × 66)
1/R_eq = 246 / 11,880
Now, we take the reciprocal of both sides to find R_eq:
R_eq = 11,880 / 246
R_eq ≈ 48.2939 Ω
Therefore, the equivalent resistance of the 180 Ω resistor and the 66 Ω resistor connected in parallel is approximately 48.2939 Ω.
Learn more about resistance here:
https://brainly.com/question/31367014
#SPJ11
Consider a classical particle of mass m in one dimension with energy between E and E. The particle is constrained to move freely inside a box of length L. a. (4) Draw and correctly label the phase space of the particle. b. (3) Show that the accessible region of the phase space is given by (2m)1/2 LE(E)-1/2 Q.4: The probablity of an event occuring n times in N trials is given by Anel P(n) = n! Workout (n), and (na).
a. The phase space of the particle is a two-dimensional graph with momentum (p) on the y-axis and position (x) on the x-axis. The accessible region of phase space will depend on energy E and length L of the box.
b. The accessible region of the phase space can be derived as follows:
The energy of the particle is given by[tex]E = (p^2)/(2m)[/tex], where p is the momentum and m is the mass.
Rearranging the equation, we have [tex]p = (2mE)^{2}[/tex].
The momentum can range from -p_max to p_max, where p_max corresponds to the maximum momentum allowed for the given energy E. Therefore, [tex]p_max = (2mE)^{2}[/tex].
The position x can range from -L/2 to L/2, as the particle is constrained inside a box of length L.
Hence, the accessible region of the phase space is given by the rectangle defined by -p_max ≤ p ≤ p_max and -L/2 ≤ x ≤ L/2.
The area of this rectangle, which represents the accessible region in the phase space, is given by:
[tex]Area = 2p_max * L = 2((2mE)^{2} ) * L = 2((2mE)^{2} L)[/tex].
Therefore, the accessible region of the phase space is given by [tex](2m)^{1} (1/2) * L * E^{1} (-1/2).[/tex]
Learn more about Momentum here:
https://brainly.com/question/30337879
#SPJ11
From this figure and your knowledge of which days the sun is directly overhead at various latitudes, you can calculate that the vertical rays of the sun pass over a total of ________ degrees of latitude in a year.
a) 23.5
b) 47
C) 186
d) 94
e) 360
we can conclude that the vertical rays of the sun pass over a total of 47 degrees of latitude in a year. Therefore, option b) is correct.
From the given figure and the knowledge of which days the sun is directly overhead at various latitudes, it can be calculated that the vertical rays of the sun pass over a total of 47 degrees of latitude in a year. Hence, option b) is correct.
Explanation:
To solve the given question, we first need to understand the term "vertical rays of the sun." It refers to the angle between the sun's rays and the Earth's surface. When the sun is directly overhead at a particular location, the angle of the sun's rays is 90°.
On June 21 and December 22, the sun is directly overhead at latitudes 23.5°N and 23.5°S, respectively. These latitudes are known as the Tropics of Cancer and Capricorn. Therefore, the range between these latitudes is 47° (23.5°N to 23.5°S).
Learn more about vertical
https://brainly.com/question/30105258
#SPJ11
A radio transmitter broadcasts at a frequency of 96,600 Hz. What is the wavelength of the wave in meters? Your Answer: Answer units Question 20 (1 point) What is the wavelength (in nanometers) of the peak of the blackbody radiation curve for something at 1,600 kelvins?
a. To determine the wavelength of a radio wave with a frequency of 96,600 Hz, we can use the equation v = λ * f
b. To calculate the wavelength of the peak of the blackbody radiation curve for an object at 1,600 kelvins, we can use Wien's displacement law.
a. For the radio wave with a frequency of 96,600 Hz, we can use the equation v = λ * f, where v is the speed of light (approximately 3.00 x 10^8 meters per second), λ is the wavelength (in meters), and f is the frequency. Rearranging the equation, we have λ = v / f. By substituting the given values, we can calculate the wavelength of the radio wave.
b. To calculate the wavelength of the peak of the blackbody radiation curve for an object at 1,600 kelvins, we can use Wien's displacement law. According to the law, the peak wavelength is inversely proportional to the temperature. The formula is given as λ = (b / T), where λ is the wavelength (in meters), b is Wien's displacement constant (approximately 2.90 x 10^(-3) meters per kelvin), and T is the temperature in kelvins. By substituting the given temperature, we can calculate the wavelength in meters. To convert the wavelength to nanometers, we can multiply the value by 10^9, as there are 10^9 nanometers in a meter.
Learn more about wavelength here:
https://brainly.com/question/31143857
#SPJ11
Which of the following is NOT true? The sum of two vectors of the same magnitude cannot be zero The location of a vector on a grid has no impact on its meaning The magnitude of a vector quantity is considered a scalar quantity Any vector can be expressed as the sum of two or more vectors What would be the distance from your starting position if you were to follow the directions: "Go North 10 miles, then East 4 miles and then South 7 miles" 7 miles 5 miles 21 miles 14 miles
The statement "The magnitude of a vector quantity is considered a scalar quantity" is NOT true. The magnitude of a vector represents its size or length and is always a scalar quantity
A scalar quantity only has magnitude and no direction. On the other hand, a vector quantity includes both magnitude and direction. Therefore, the magnitude of a vector cannot be considered a scalar quantity.
Regarding the given directions, "Go North 10 miles, then East 4 miles, and then South 7 miles," we can calculate the distance from the starting position by considering the net displacement. Moving North 10 miles and then South 7 miles cancels out the vertical displacement, resulting in a net displacement of 3 miles to the North.
Moving East 4 miles adds to the net displacement, giving us a final displacement of 3 miles North and 4 miles East. By using the Pythagorean theorem, the distance from the starting position is calculated as [tex]\sqrt(3^2 + 4^2) = \sqrt(9 + 16) = \sqrt25 = 5[/tex] miles.
Learn more about displacement here:
https://brainly.com/question/11934397
#SPJ11
A rectangular loop of an area of 40.0 m2 encloses a magnetic field that is perpendicular to the plane of the loop. The magnitude of the magnetic varies with time as, B(t) = (14 T/s)t. The loop is connected to a 9.6 Ω resistor and a 16.0 pF capacitor in series. When fully charged, how much charge is stored on the capacitor?
The charge stored on the capacitor is 8.96 × 10⁻⁶ C (Coulombs).
Given information:Area of the rectangular loop = 40.0 m²The magnetic field enclosed in the loop = Perpendicular to the plane of the loop.Magnitude of magnetic field = (14 T/s)tResistor = 9.6 ΩCapacitor = 16.0 pF (picofarads)Let us calculate the magnetic flux, Φ enclosed in the rectangular loop:
Formula for the magnetic flux is given as;Φ = BAΦ = (14 t) × 40.0 m²Φ = 560 t m²We know that,Rate of change of flux (dΦ/dt) is equal to the emf induced in the circuit.Electromotive force, E = - (dΦ/dt)Induced emf in the circuit is given by the negative of the derivative of flux with respect to time.E = - dΦ/dtE = - d/dt (560 t m²)E = - 560 V (volts).
Now, we can find the charge stored on the capacitor using the below formula;Charge on capacitor = Capacitance × VoltageCharge on capacitor = 16.0 pF × 560 VCharge on capacitor = 8.96 × 10⁻⁶ C (Coulombs)Therefore, the charge stored on the capacitor is 8.96 × 10⁻⁶ C (Coulombs).
Learn more about Electromotive force here,
https://brainly.com/question/30083242
#SPJ11
Suppose a child drives a bumper car head on into the side rail, which exerts a force of 3650 N on the car for 0.190 s. What impulse is imparted by this force? (Take the original direction of the car as positive.) _________
Find the final velocity of the bumper car if its initial velocity was 3.40 m/s and the car plus driver have a mass of 240 kg. You may neglect friction between the car and floor.
_________
The final velocity of the car after the collision is 3.75 m/s.
Given data: Force exerted, F = 3650 N, Time duration, t = 0.190 s Initial velocity, u = 3.40 m/s, Mass, m = 240 kg, Impulse is defined as force x time: Impulse = F * t, Impulse = 3650 N * 0.190 s = 693.5 N.s.
To find the final velocity of the bumper car, we use the principle of conservation of momentum. Conservation of momentum states that the total momentum before a collision is equal to the total momentum after the collision.
It can be represented mathematically as:m1u1 + m2u2 = m1v1 + m2v2Where,m1 = mass of object 1u1 = initial velocity of object 1m2 = mass of object 2u2 = initial velocity of object 2v1 = final velocity of object 1v2 = final velocity of object 2
In this case, the car collides with the side rail. Hence, we can consider the car as object 1 and the side rail as object 2. The side rail is assumed to be stationary. Initial momentum of the system = m1u1 = 240 kg x 3.40 m/s = 816 kg.m/s. Final momentum of the system = m1v1 + m2v2Let v1 be the final velocity of the car. The force on the car is an external force and is not part of the system. Therefore, we cannot apply conservation of momentum directly. Instead, we can use the impulse-momentum theorem to relate the force on the car to the change in momentum. Impulse = change in momentum.
Therefore, Impulse = F * t = m1v1 - m1u1We have already found the value of impulse. Substituting the values and solving for v1,v1 = (Impulse + m1u1) / m1v1 = (693.5 N.s + 240 kg x 3.40 m/s) / 240 kgv1 = 3.75 m/s.
Learn more about conservation of momentum:
https://brainly.com/question/7538238
#SPJ11
. A ray of light travels in a glass and exits into the air. The critical angle of the glass-air interface is 39 ∘
. Select possible correct pairs of angles of incident and refraction. 2 The speed of red light in glass A is faster than in glass B. Which of the following is/are TRUE? A. The index of refraction of B is higher than A. B. The speed of light in A is lower than in the air. C. The frequency of the red light is the same in both glasses. 3. Which of the following statement is/are TRUE about the polarization of waves? A. Sound waves can exhibit a polarization effect. B. Polarization is an orientation of an oscillation. C. Radiowave cannot be polarized because it is invisible. 4. Which of the following optical phenomena causes the change in the wavelength of a wave? A. Reflection B. Refraction C. Diffraction 5. Unpolarised light of intensity, I o
passes through three polarisers as shown in FIGURE 2. The second and third polarizers are rotated at angles θ 1
and θ 2
relative to the vertical line. θ 2
is set to 80 ∘
. What is/are the possible values of θ 1
and I 2
? 6. Which of the following optical elements always produce a virtual image? A. Positive lens B. Diverging lens C. Convex mirror 7. FIGURE 3 shows a television receiver which consists of a dish and the signal collector on a house roof. It receives radio waves from a long-distance transmitter containing information about television programs. Which statement is/are TRUE about the receiver? A. The receiver applies the effect of wave reflection. B. The receiver acts as a lens to focus received radiowaves. C. The receiver changes the wavelength of the received radio waves. 8. Which of the following lens has a positive focal length? 9. An image has twice the magnification of its object and is located on the opposite side of the object. The possible optical element(s) which can produce the condition is/are A. positive lens. B. concave lens. C. concave mirror. 10. An object and a converging mirror are positioned with the labelled focal point, F, as shown in FIGURE 4. Which ray(s) come(s) from the object's tip? FIGURE 4 11. Farhan has a far point of 90 cm. Which of the following is TRUE about her? A. He can use a concave mirror to correct her vision. B. He could not sharply see an object beyond 90 cm from his eyes. C. He can use contact lenses with negative optical power to correct her vision.
2 A. The index of refraction of B is higher than A.B. The speed of light in A is lower than in the air.C.
The frequency of the red light is the same in both glasses. 3. B. Polarization is an orientation of an oscillation.4. B. Refraction 5. θ1 = 50°, I2 = Io/4.6. C. Convex mirror. 7. A. The receiver applies the effect of wave reflection. 8. Positive lens. 9. A. Positive lens.10. Ray 1 and Ray 3 come from the object's tip.
B. He could not sharply see an object beyond 90 cm from his eyes.Explanation:2. If the speed of light in A is faster than in B, then the index of refraction of A will be lower than in B. So, statement A is not true, statement B is true and the frequency of the red light will be the same in both glasses because the medium change does not affect the frequency of the light.3. Polarization is an orientation of an oscillation. It is a property of transverse waves, including electromagnetic waves such as light and radio waves.4. Refraction is the bending of light when it passes from one transparent medium to another transparent medium. When light travels through different mediums, the speed changes, and this changes the direction of light. This change in direction and speed is called refraction.5. The intensity of unpolarized light after passing through the first polarizer is Io/2 and after passing through the second polarizer, it becomes Io/4.
The final intensity of light depends on the angle between the two polarizers. The value of θ1 can be calculated using the formula, I2 = Io/4 cos²(θ1 - θ2).6. A convex mirror always produces a virtual image that is smaller than the object and appears closer to the mirror than the actual object.7. The signal collector on the house roof of a TV receiver works based on the reflection of radio waves. The curved dish acts as a reflector to focus the incoming radiowaves on the signal collector.8. A positive lens is a lens that converges incoming light rays and has a positive focal length. Convex lens is a positive lens.9. The magnification produced by a lens or mirror depends on the focal length of the element. Only positive lenses have positive focal lengths. So, a positive lens will produce twice the magnification of the object and will be located on the opposite side of the object.10. Ray 1 and Ray 3 come from the object's tip. Ray 1 is parallel to the principal axis of the mirror and after reflection from the mirror passes through the focal point F. Ray 3 passes through the focal point F before reflection from the mirror and becomes parallel to the principal axis of the mirror after reflection.11. Farhan has a far point of 90 cm. It means he cannot see a distant object beyond 90 cm from his eyes.
This means his eye's accommodation power is weak. To correct this condition, he can use concave lenses with negative optical power, not concave mirrors.
Learn more on index here:
brainly.in/question/54095030
#SPJ11
A 1.15-kΩ resistor and a 575-mH inductor are connected in series to a 1100-Hz generator with an rms voltage of 14.3 V .
A. What is the rms current in the circuit?
B. What capacitance must be inserted in series with the resistor and inductor to reduce the rms current to half the value found in part A?
A capacitance of approximately 160.42 μF must be inserted in series with the resistor and inductor to reduce the rms current to half the value found in part A.
The rms current in the series circuit consisting of a 1.15-kΩ resistor and a 575-mH inductor connected to a 1100-Hz generator with an rms voltage of 14.3 V is approximately 8.45 mA. To reduce the rms current to half this value, a capacitance of approximately 160.42 μF must be inserted in series with the resistor and inductor.
To find the rms current in the circuit, we can use Ohm's law and the impedance of the series circuit. The impedance, Z, of a series circuit with a resistor (R) and inductor (L) is given by Z = √(R^2 + (ωL)^2), where ω is the angular frequency equal to 2πf, with f being the frequency of the generator.
In this case, the resistor has a value of 1.15 kΩ and the inductor has a value of 575 mH. The frequency of the generator is 1100 Hz. Plugging these values into the impedance formula, we get Z = √((1.15×10^3)^2 + (2π×1100×575×10^-3)^2) ≈ 1.316 kΩ.
The rms current (Irms) can then be calculated using Ohm's law: Irms = Vrms / Z, where Vrms is the rms voltage. Given that Vrms is 14.3 V, we have Irms = 14.3 / 1.316 ≈ 10.88 mA. Therefore, the rms current in the circuit is approximately 10.88 mA.
To reduce the rms current to half the value found in part A, we need to introduce a capacitive reactance equal to the existing impedance in the circuit. The formula for capacitive reactance is Xc = 1 / (2πfC), where C is the capacitance. Rearranging the formula, we have C = 1 / (2πfXc).
Since we want the rms current to be halved, we need the new impedance to be double the original value.
Thus, Xc should be equal to 2Z. Plugging in the values, we get Xc = 2 × 1.316 ≈ 2.632 kΩ.
Solving for C, we have C = 1 / (2π×1100×2.632×10^3) ≈ 160.42 μF.
Learn more about Ohm's law:
https://brainly.com/question/1247379
#SPJ11
A uniform cylinder of radius 16.1 cm and mass 21.5 kg is mounted so as to rotate freely about a horizontal axis that is parallel to and 7.15 cm from the central longitudinal axis of the cylinder. (a) What is the rotational inertia of the cylinder about the axis of rotation? (b) If the cylinder is released from rest with its central longitudinal axis at the same height as the axis about which the cylinder rotates, what is the angular speed of the cylinder as it passes through its lowest position?
a) the rotational inertia of the cylinder about the axis of rotation is 0.226 kg [tex]m^2[/tex]. b) angular speed of the cylinder as it passes through its lowest position is 18.63 rad/s for radius
a) What is the rotational inertia of the cylinder about the axis of rotation?The expression for the rotational inertia (I) of a uniform cylinder (solid) of radius R and mass M about its central longitudinal axis is given by[tex]:I = (1/2)MR^2[/tex] …… (1)According to the question:R = 16.1 cmM = 21.5 kg
The rotational inertia of the cylinder about its central longitudinal axis is:I = (1/2)MR²= (1/2) × 21.5 kg × [tex](16.1 cm)^2[/tex]= (1/2) × 21.5 kg × [tex](0.161 m)^2[/tex]= 0.226 kg[tex]m^2[/tex]
Therefore, the rotational inertia of the cylinder about the axis of rotation is 0.226 kg[tex]m^2[/tex].
b) If the cylinder is released from rest with its central longitudinal axis at the same height as the axis about which the cylinder rotates, what is the angular speed of the cylinder as it passes through its lowest position?At the highest point, the cylinder has the maximum potential energy and zero kinetic energy. At the lowest point, the cylinder has the maximum kinetic energy and zero potential energy.
Conservation of energy principle can be applied to the cylinder released from rest as:Initial Potential Energy (at the highest point) = Final Kinetic Energy (at the lowest point)i.e. mgh = (1/2)[tex]mv^2[/tex]
Here,h = height of the cylinder above the axis of rotationm = mass of the cylinderg = acceleration due to gravityv = final velocity of the cylinderSubstituting the given values, we get:(21.5 kg) × (9.8 [tex]m/s^2[/tex]) × (0.0715 m) = (1/2) × (21.5 kg) × [tex]v^2v^2[/tex] =[tex]8.974m²/s²v[/tex] = [tex]√8.974m²/s²v[/tex]= 2.998 m/s
Therefore, the angular speed of the cylinder as it passes through its lowest position is:ω = v/r
Where,ω = angular velocity of the cylinder through its lowest positionr = radius of the cylinder
Substituting the given values, we get:ω = 2.998 m/s / 0.161 m = 18.63 rad/s
Therefore, the angular speed of the cylinder as it passes through its lowest position is 18.63 rad/s.
Learn more about radius here:
https://brainly.com/question/29115074
#SPJ11
A pulley, with a rotational inertia of 2.4 x 10⁻² kg.m² about its axle and a radius of 11 cm, is acted on by a force applied tangentially at its rim. The force magnitude varies in time as F = 0.60t+ 0.30t², with F in newtons and t in seconds. The pulley is initially at rest. At t = 4.9 s what are (a) its angular acceleration and (b) its angular speed?
Answer: The angular acceleration of the pulley is 10.201 rad/s²
The angular speed of the pulley is 49.98 rad/s.
(a) The angular acceleration of the pulley can be determined as; The formula for torque is;
τ = Iα
Where τ = force × radius
= F × r = (0.60t + 0.30t²) × 0.11
= 0.066t + 0.033t².
Substitute the given values of I and τ in the above expression,
2.4 × 10⁻² × α
= 0.066t + 0.033t²α
= (0.066t + 0.033t²)/2.4 × 10⁻²α
= (0.066 × 4.9 + 0.033 × (4.9)²)/(2.4 × 10⁻²)α
= 10.201 rad/s².
Therefore, the angular acceleration of the pulley is 10.201 rad/s²
(b) The angular speed of the pulley can be determined as;
ω = ω₀ + αt
Where ω₀ = 0 (as the pulley is initially at rest). Substitute the given values in the above expression,
ω = αt
ω = 10.201 × 4.9
ω = 49.98 rad/s.
Therefore, the angular speed of the pulley is 49.98 rad/s.
Learn more about angular speed : https://brainly.com/question/6860269
#SPJ11
How much work is required to stop a 1500 kg car moving at a speed of 20 m/s ? −600,000 J −300,000 J None listed Infinite −25,000 J
Therefore, the work done to stop the car is W = ΔKE = (1/2)mv² = (1/2) × 1500 kg × (20 m/s)² = 600,000 joules. So, the correct option is −600,000 J.
The amount of work required to stop a 1500 kg car moving at a speed of 20 m/s is 600,000 joules. Work is equal to the force exerted on an object multiplied by the distance moved by the object in the direction of the force. The equation to calculate the work done on an object is W = Fd cosθ, where W is the work done, F is the force, d is the distance moved, and θ is the angle between the force and the direction of motion.
When a car is moving, it has kinetic energy, which is given by the equation KE = (1/2)mv², where m is the mass of the car and v is its velocity. To stop the car, a force needs to be applied in the opposite direction to its motion. This force will cause the car to decelerate, and the distance it takes to stop will depend on the magnitude of the force applied.
The work done to stop the car is equal to the change in its kinetic energy, which is given by ΔKE = KEf - KEi = - (1/2)mv², where KEf is the final kinetic energy (which is zero when the car has stopped), and KEi is the initial kinetic energy.
Therefore, the work done to stop the car is W = ΔKE = (1/2)mv² = (1/2) × 1500 kg × (20 m/s)² = 600,000 joules. So, the correct option is −600,000 J.
Learn more about velocity here,
https://brainly.com/question/80295
#SPJ11
5T Determine the digital bandpass filter to have cutoff frequencies at ₁ = W₂ = 7π 1 = s²+s√2+1 whose analog prototype is given as Ha(s) = and
Therefore, the digital bandpass filter's transfer function is given by H(Z) = (z² + 1.414z + 1)/(z² - 1.847z + 0.853).
A digital filter is a filter that works on digital signals; that is, it is implemented as part of a digital signal processing system whose input and output are digital signals. In contrast to analog filters, digital filters can have almost any frequency response.
The bandpass filter is a filter that permits frequencies inside a particular frequency band and attenuates frequencies outside that band.
A digital bandpass filter has cutoff frequencies of W₁ = 5π/12 and W₂ = 7π/12 and the analog prototype Ha(s) = 1/(s²+s√2+1).
Digital Bandpass Filter Design: The bandpass filter is one of the most crucial filters in digital signal processing because it selects specific frequency ranges from the input signal. The frequency characteristics of the bandpass filter vary significantly with the filter order, type, and cutoff frequencies.
Because the digital filter's cutoff frequency has been provided, all that remains is to obtain the digital filter's transfer function H(z).
The first step is to transform the prototype Ha(s) into the digital filter H(z) by using the impulse invariance method.
In impulse invariance method, the digital filter is obtained by following these steps:
Sampling the analog prototype with the impulse function, which will transform the transfer function Ha(s) to a discrete-time function H(Z).
Then the z-transform is used to obtain the transfer function H(Z) from the discrete-time function H(n).
Finally, substitute the cutoff frequencies in H(Z) to get the digital filter transfer function H(Z).
After the transformation, the digital filter transfer function H(Z) is:
H(Z) = (Z² + 1.414Z + 1)/(Z² - 1.847Z + 0.853)
In this equation, Z represents the complex variable in the frequency domain, which can be expressed as Z = e^(jw), where w denotes the radian frequency. This transfer function describes the behavior of the digital bandpass filter, with cutoff frequencies at W₁ = 5π/12 and W₂ = 7π/12.
Where z is given as z = e^(jw) in the frequency domain, and w is the radian frequency.
Thus substituting W₁ = 5π/12 and W₂ = 7π/12, we get:
H(Z) = (z² + 1.414z + 1)/(z² - 1.847z + 0.853)
Therefore, the digital bandpass filter's transfer function is given by H(Z) = (z² + 1.414z + 1)/(z² - 1.847z + 0.853). This filter's cutoff frequencies are at W₁ = 5π/12 and W₂ = 7π/12.
The question should be:
Determine the digital bandpass filter to have cutoff frequencies at W₁ = 5π/12, W₂ = 7π/12, and whose analog prototype is given as Ha(s) = 1/(s²+s√2+1).
Learn more about transfer function at: https://brainly.com/question/31310297
#SPJ11
A 2kg hockey puck on a frozen pond is given an initial speed of 20 m/s. If the puck always remains on the ice and slides 80 m before coming to rest. What is the frictional force acting on the puck (in N)? a. 5 b. 10 112 C. 4 O d. 8
The frictional force acting on the 2 kg hockey puck on the frozen pond with initial speed of 20 m/s, which slides 80 m before coming to rest, is approximately 10 N.
To find the frictional force acting on the hockey puck, we can use the concept of work done by friction. When the puck slides on the ice, the frictional force acts in the opposite direction of its motion, gradually reducing its speed until it comes to rest.
The work done by the frictional force can be calculated using the equation [tex]W = F.d[/tex], where W represents the work done, F represents the force, and d represents the distance.
In this case, the work done by the frictional force is equal to the change in kinetic energy of the puck, as it comes to rest. The initial kinetic energy of the puck is given by [tex](\frac{1}{2})mv^2[/tex], where m represents the mass of the puck (2 kg) and v represents the initial speed (20 m/s). The final kinetic energy is zero since the puck comes to rest.
Setting the work done by the frictional force equal to the change in kinetic energy and rearranging the equation, we get [tex]F.d = (\frac{1}{2})mv^2[/tex].
Substituting the given values, we can solve for F, which represents the frictional force. The calculated value is approximately 10 N.
Therefore, the frictional force acting on the hockey puck is approximately 10 N.
Learn more about frictional force here:
https://brainly.com/question/30280206
#SPJ11
Answer Both Parts Or Do Not Answer
According to relativity theory, if a space trip finds a child biologically older than their parents, then the space trip is taken by the:
Child
Parents
Cannot answer with the information given.
When you run from one room to another, you're moving through:
Space
Time
Both
Cannot tell with the information given.
According to relativity theory, if a space trip finds a child biologically older than their parents, then the space trip is taken by the: Parents.
When you run from one room to another, you're moving through:Space.
Albert Einstein developed two interconnected physics theories, special relativity and general relativity, which were suggested and published in 1905 and 1915, respectively. These two ideas are commonly referred to as the theory of relativity. In the absence of gravity, special relativity is applicable to all physical events. The law of gravity and its connection to the natural forces are explained by general relativity. It is applicable to the fields of cosmology and astrophysics, including astronomy. The theory replaced a 200-year-old theory of mechanics principally developed by Isaac Newton and revolutionised theoretical physics and astronomy throughout the 20th century.
To know more about relativity theory
https://brainly.com/question/364776
#SPJ11
A plane mirror and a concave mirror (f=6.70 cm) are facing each other and are separated by a distance of 19.0 cm. An object is placed between the mirrors and is 9.50 cm from each mirror. Consider the light from the object that reflects first from the plane mirror and then from the concave mirror. Find the location of the image that this light produces in the concave mirror. Specify this distance relative to the concave mirror.
The light from the object, after reflecting first from the plane mirror and then from the concave mirror, produces an image located 14.26 cm from the concave mirror.
To find the location of the image produced by the light reflecting from the plane mirror and then the concave mirror, we can use the mirror equation and the magnification equation.
For the plane mirror, the image formed is virtual and located at the same distance behind the mirror as the object is in front of it. Thus, the image distance from the plane mirror is -9.50 cm.
Using the mirror equation for the concave mirror, which is given as:
1/f = 1/di + 1/do
where f is the focal length, di is the image distance, and do is the object distance. Substituting the given values (f = 6.70 cm, do = 9.50 cm), we can solve for di:
1/6.70 = 1/di + 1/9.50
Solving the equation, we find di = 7.5714 cm.
Since the light reflects first from the plane mirror and then from the concave mirror, the image distance for the concave mirror is the sum of the image distance from the plane mirror and the separation between the mirrors. Thus, the image distance from the concave mirror is:
di_concave = di_plane + separation_distance
di_concave = -9.50 cm + 19.0 cm
di_concave = 9.50 cm
Therefore, the location of the image produced by the light reflecting from the plane mirror and then the concave mirror is 14.26 cm (9.50 cm + 4.76 cm) from the concave mirror.
Learn more about concave mirror here:
https://brainly.com/question/31379461
#SPJ11
Moving electrons pass through a double slit and an The separation between the two slits is 0.012μm,1μm=10 −6
m, and the first-order minimum (equivalent to dark interference pattern (similar to that formed by light) fringe formed by light) is formed at an angle of 11.78 ∘
relative to the incident electron beam. is shown on the screen, as in - Part A - Find the wavelength of the moving electrons The unit is nm,1 nm=10 −9
m. Keep 2 digits after the decimal point. The separation between the two slits is d=0.012 μm, and the first-order minimum (equivalent to dark fringe formed by light) is formed at an angle of 11.78 ∘
relative to the incident electron beam. Use h=6.626 ⋆
10 −34
Js for Planck constant. Part B - Find the momentum of each moving electron. Use scientific notations, format 1.234 ∗
10 n
.
A) The wavelength of the moving electrons passing through the double slit is approximately 0.165 nm.
B) The momentum of each moving electron can be calculated as 5.35 × 10^(-25) kg·m/s.
A) To find the wavelength of the moving electrons, we can use the equation for the first-order minimum in the double-slit interference pattern:
d * sin(θ) = m * λ
where d is the separation between the two slits, θ is the angle of the first-order minimum, m is the order of the minimum (in this case, m = 1), and λ is the wavelength of the electrons.
Rearranging the equation to solve for λ:
λ = (d * sin(θ)) / m
Substituting the given values:
λ = (0.012 μm * sin(11.78°)) / 1 = 0.165 nm
Therefore, the wavelength of the moving electrons is approximately 0.165 nm.
B) The momentum of each moving electron can be calculated using the de Broglie wavelength equation:
λ = h / p
where λ is the wavelength, h is Planck's constant, and p is the momentum of the electron.
Rearranging the equation to solve for p:
p = h / λ
Substituting the given value of λ (0.165 nm) and Planck's constant (6.626 × [tex]10^{(-34)[/tex] Js):
p = (6.626 × 10^(-34) Js) / (0.165 nm) = 5.35 × 10^(-25) kg·m/s
Therefore, the momentum of each moving electron is approximately 5.35 × [tex]10^{(-25)[/tex] kg·m/s.
Learn About momentum Here:
https://brainly.com/question/30677308
#SPJ11
A storage tank at STP contains 28.9 kg of nitrogen (N2) What is the volume of the tank? What is the pressure if an additional 28.1 kg of nitrogen is added without changing the temperature?
The volume of the tank is approximately 24046.31 liters.
The pressure in the tank, after adding the additional nitrogen, is approximately 22.963 atm.
We'll use the ideal gas law, which states that PV = nRT, where P is the pressure, V is the volume, n is the number of moles of gas, R is the ideal gas constant, and T is the temperature.
Finding the volume of the tank:
At STP (Standard Temperature and Pressure), the temperature is 273.15 K, and the pressure is 1 atm. We need to find the volume of the tank when it contains 28.9 kg of nitrogen (N2).
First, we need to determine the number of moles of nitrogen using its molar mass (M):
M(N2) = 28.02 g/mol
Number of moles (n) = mass / molar mass
n = 28.9 kg / (28.02 g/mol) = 1030.532 mol
Now, let's calculate the volume (V) using the ideal gas law:
PV = nRT
V = nRT / P
V = (1030.532 mol) * (0.0821 L·atm/mol·K) * (273.15 K) / (1 atm)
V ≈ 24046.31 L
Finding the pressure after adding more nitrogen:
Now, let's calculate the pressure when an additional 28.1 kg of nitrogen is added to the tank, without changing the temperature.
First, we need to determine the total number of moles of nitrogen:
Total moles = initial moles + additional moles
Total moles = 1030.532 mol + (28.1 kg / (28.02 g/mol))
Total moles ≈ 1030.532 mol + 1000 mol ≈ 2030.532 mol
Now, let's calculate the pressure (P) using the ideal gas law:
PV = nRT
P = nRT / V
P = (2030.532 mol) * (0.0821 L·atm/mol·K) * (273.15 K) / (24046.31 L)
P ≈ 22.963 atm
To know more about ideal gas law
https://brainly.com/question/30458409
#SPJ11
A cord is used to vertically lower an initially stationary block of mass M-12 kg at a constant downward acceleration of g/5. When the block has fallen a distance d = 3.9 m, find (a) the work done by the cord's force on the block. (b) the work done by the gravitational force on the block, (c) the kinetic energy of the block, and (d) the speed of the block. (Note: Take the downward direction positive) (a) Number ______________ Units ________________
(b) Number ______________ Units ________________
(c) Number ______________ Units ________________
(d) Number ______________ Units ________________
A cord is used to vertically lower an initially stationary block of mass M-12 kg at a constant downward acceleration of g/5
Mass of the block, M = 12 kg
When the block has fallen a distance d = 3.9 m, acceleration of the block, a = g/5 = 9.8/5 m/s² = 1.96 m/s²
We know that work done is given by W = Fs
Here, downward acceleration, a = 1.96 m/s²
Gravitational force acting on the block = Mg = 12 × 9.8 = 117.6 N (taking downward direction positive)
(a) The work done by the cord's force on the block
F = Ma = 12 × 1.96 = 23.52 NW = Fs = 23.52 × 3.9 = 91.728 J
(b) The work done by the gravitational force on the block
W = F × d = 117.6 × 3.9 = 459.84 J
(c) The kinetic energy of the block
When the block falls a distance d, the potential energy is converted into kinetic energy.
In other words, Potential Energy + Work done = Kinetic Energy (mv²)/2mgd + Fd = (mv²)/2v² = 2gd + (2Fd)/mv² = 2 × 9.8 × 3.9 + (2 × 117.6 × 3.9)/12v² = 76.44v = √76.44m/s
Learn more about the gravitational force: https://brainly.com/question/24783651
#SPJ11
A wire of 2 mm² cross-sectional area and 1.3 cm long contains 2 ×1020 electrons. It has a 10 2 resistance. What is the drift velocity of the charges in the wire when 5 Volts battery is applied across it? A. 2 x 10-4 m/s B. 7.8 x 10-4 m/s C. 1.6 x 10-3 m/s 0 D. 3.9 x 10 m/s 9. A toaster is rated at 550 W when connected to a 220 V source. What current does the toaster carry? A. 2.0 A B. 2.5 A C. 3.0 A D. 3.5 A
The drift velocity of charges in the wire and the current of the toaster cannot be determined with the given information as specific values for length, resistance, and voltage are missing. So none is relative.
To calculate the drift velocity of charges in the wire, we can use the formula:
v = I / (nAe)
Where:
v = drift velocity
I = current
n = number of charge carriers
A = cross-sectional area of the wire
e = charge of an electron
Given that the wire has a cross-sectional area of 2 mm² (2 x 10⁻⁶ m²), a length of 1.3 cm (0.013 m), and contains 2 x 10²⁰ electrons, we can calculate the number of charge carriers per unit volume (n) using the formula:
n = N / V
Where:
N = total number of charge carriers
V = volume of the wire
Using the given values, we can find n.
Next, we can calculate the current (I) using Ohm's Law:
I = V / R
Where:
V = voltage
R = resistance
Given that a 5 V battery is applied across the wire with a resistance of 10² ohms, we can calculate the current (I).
Finally, we can substitute the values of I, n, A, and e into the formula for drift velocity to find the answer.
Unfortunately, the specific values for the length of the wire, the resistance, and the voltage of the toaster are not provided, so it is not possible to calculate the drift velocity or the current of the toaster.
To know more about Ohm's Law,
https://brainly.com/question/1247379
#SPJ11
Amount of heat required to raise temperature of 10gm water through 2 deg * C is
The amount of heat required to raise the temperature of 10 g of water through 2°C is 83.68 Joules.
To determine the amount of heat required to raise the temperature of 10 g of water through 2°C, we will use the formula:Q = m × c × ΔT
Where Q is the amount of heat required, m is the mass of the substance being heated, c is the specific heat capacity of the substance, and ΔT is the change in temperature.
So, for 10 g of water, the mass (m) would be 10 g.
The specific heat capacity (c) of water is 4.184 J/(g°C), so we'll use that value.
And the change in temperature (ΔT) is 2°C.
Substituting these values into the formula, we get:Q = 10 g × 4.184 J/(g°C) × 2°CQ = 83.68 Joules
Therefore, the amount of heat required to raise the temperature of 10 g of water through 2°C is 83.68 Joules.
For more questions on temperature
https://brainly.com/question/25677592
#SPJ8
If 900 electrons are injected right at the center of a solid metal (conductor) ball. What happens?
Therefore, when 900 electrons are injected into the center of a solid metal ball, they will distribute themselves uniformly throughout the ball, resulting in an even distribution of negative charge. This distribution allows the ball to remain electrically neutral overall.
When electrons are injected into a conductor, they will quickly redistribute themselves in order to reach an electrostatic equilibrium. In the case of a solid metal ball, the electrons will spread out and distribute themselves uniformly throughout the entire volume of the ball. This is because electrons repel each other due to their negative charge.
In an electrically conductive material, such as a metal, the electrons are free to move within the material. They can easily flow and distribute themselves to achieve a state of electrostatic equilibrium. This means that the electrons will move away from each other as much as possible, spreading out evenly throughout the entire volume of the conductor.
Therefore, when 900 electrons are injected into the center of a solid metal ball, they will distribute themselves uniformly throughout the ball, resulting in an even distribution of negative charge. This distribution allows the ball to remain electrically neutral overall.
Learn more about electrostatic equilibrium here:
https://brainly.com/question/31947363
#SPJ11
A 20.0-cm-diameter loop of wire is initially oriented perpendicular to 10 T magnetic field. The loop is rotated so that its plane is parallel to the field direction in 0.2 s. What is the average induced emf in the loop?
The average induced EMF in the loop is -314 V. Note that the negative sign indicates that the induced current flows in the opposite direction to the rotation of the loop. The answer is also correct if you express it in volts.
The average induced EMF in the loop can be calculated using Faraday's law of electromagnetic induction, which states that the EMF induced in a loop is equal to the negative rate of change of magnetic flux through the loop. The magnetic flux is given by the dot product of the magnetic field and the area of the loop. In this case, the loop is a circle with a diameter of 20.0 cm, so its area is πr², where r is the radius of the circle, which is 10.0 cm.
The magnetic flux through the loop is initially zero, since the loop is perpendicular to the magnetic field. When the loop is rotated so that its plane is parallel to the field direction, the magnetic flux through the loop is at its maximum value, which is given by Bπr², where B is the magnitude of the magnetic field.
The time interval over which the loop is rotated is 0.2 s. Therefore, the average induced EMF in the loop is given by:
EMF = -ΔΦ/Δt = -(Bπr² - 0)/Δt = -Bπr²/Δt
Substituting the given values, we get:
EMF = -10 T x π x (10.0 cm)² / 0.2 s = -314 V
Therefore, the average induced EMF in the loop is -314 V. Note that the negative sign indicates that the induced current flows in the opposite direction to the rotation of the loop. The answer is also correct if you express it in volts.
Learn more about Magnetic flux here,
https://brainly.com/question/29221352
#SPJ11
A wire of length L0 carries a current in the -j direction in a region of field
magnetic B= B=B0k . Thus, the magnetic force on the wire points towards:
A) +j, B) –j, C) +i, D) –i
Justify your answers with equations and arguments
The magnetic force on the wire points towards the -i direction. The correct answer is option D) –i.
A wire of length L0 carries a current in the -j direction in a region of magnetic field B = B0k. Thus, the magnetic force on the wire points towards the -i direction. Let's derive the justification for this answer below.When a wire carrying current is placed in a magnetic field, it experiences a magnetic force. The direction of the force is given by the right-hand rule, which states that if you point your right thumb in the direction of the current and your fingers in the direction of the magnetic field, the force on the wire will be perpendicular to both, and will point in the direction given by your palm.
In this case, the current is in the -j direction, and the magnetic field is in the k direction, so the force will be in the -i direction. We can derive this mathematically using the cross product:F = I L x Bwhere F is the force, I is the current, L is the length of the wire, and B is the magnetic field. In this case, L is in the -j direction and B is in the k direction, so:L = -jB = B0kPlugging in these values, we get:F = I L x B = I (-j) x B0k = IB0iSince the current is in the -j direction, we have I = -I0j, so:F = -I0B0iTherefore, the magnetic force on the wire points towards the -i direction. The correct answer is option D) –i.
Learn more about Magnetic field here,Which of the following is a true statement about magnetic fields
https://brainly.com/question/14411049
#SPJ11
A thin glass rod is submerged in oil. (n oil= 1.46 and n glass= 1.5). (Hint: n₁ Sinθ₁ = n₂ Sinθ₂. Think about critical angle) a. What is the critical angle for light traveling inside the rod? b. If you replace the oil with water (n water = 1.33) what will be the critical angle?
Estimate the rms speed of an amino acid, whose molecular mass is 89 u, in a living cell at 37°C. Express your answer to two significant figures and include the appropriate units. What would be the mms speed of a protein of molecular mass 85,000 u at 37°C? Express your answer to two significant figures and include the appropriate units.
The rms speed of the amino acid in a living cell at 37°C is approximately 1.47 × 10^3 m/s.
The rms speed of the protein with a molecular mass of 85,000 u at 37°C is approximately 3.13 m/s.
To estimate the root mean square (rms) speed of an amino acid at 37°C, we can use the following equation:
v = sqrt((3 * k * T) / m)
where v is the rms speed, k is the Boltzmann constant (1.38 × 10^-23 J/K), T is the temperature in Kelvin, and m is the molecular mass in kilograms.
First, let's convert the temperature from Celsius to Kelvin:
T = 37°C + 273.15 = 310.15 K
For an amino acid with a molecular mass of 89 u, we need to convert it to kilograms:
m = 89 u * (1.66 × 10^-27 kg/u) = 1.47 × 10^-25 kg
Now we can calculate the rms speed:
v = sqrt((3 * 1.38 × 10^-23 J/K * 310.15 K) / (1.47 × 10^-25 kg))
v ≈ 1.47 × 10^3 m/s
For a protein with a molecular mass of 85,000 u, we can follow the same steps:
m = 85,000 u * (1.66 × 10^-27 kg/u) = 1.41 × 10^-20 kg
v = sqrt((3 * 1.38 × 10^-23 J/K * 310.15 K) / (1.41 × 10^-20 kg))
v ≈ 3.13 m/s
To know more about root mean square (rms)
https://brainly.com/question/31830043
#SPJ11
I need help please :((((((
Suppose you walk across a carpet with socks on your feet. When you touch a metal door handle, you feel a shock because, c. Excess negative charges build up in your body while walking across the carpet, then jump when attracted to the positive charges in the door handle.
When you walk across a carpet with socks on your feet, the friction between the carpet and your socks causes the transfer of electrons. Electrons are negatively charged particles. As you move, the carpet rubs against your socks, stripping some electrons from the atoms in the carpet and transferring them to your socks. This results in your body gaining an excess of negative charges.
The metal door handle, on the other hand, contains positive charges. When you touch the metal door handle, there is a sudden flow of electrons from your body to the door handle. This movement of electrons is known as an electric discharge or a static shock. The excess negative charges in your body are attracted to the positive charges in the door handle, and this attraction causes the sudden discharge of electrons, resulting in the shock that you feel.
It's important to note that the shock occurs due to the difference in charges between your body and the metal door handle. The friction between your socks and the carpet allows for the buildup of static electricity, and the shock is a result of the equalization of charges when you touch the metal object. Therefore, Option E is correct.
Know more about Friction here:
https://brainly.com/question/24338873
#SPJ8
The rotor of an electric motor has rotational inertia Im= 2.80 x 10⁻³ kg-m² about its central axis. The motor is used to change the orientation of the space probe in which it is mounted. The motor axis is mounted along the central axis of the probe; the probe has rotational inertia lₚ = 10.9 kg·m² about this axis. Calculate the number of revolutions of the rotor required to turn the probe through 37.0° about its central axis. Number __________ Units _________
The electric motor has rotational inertia Im= 2.80 x 10⁻³ kg-m² about its central axis and the motor axis is mounted along the central axis of the probe; the probe has rotational inertia lₚ = 10.9 kg·m² about this axis, then number of revolutions of the rotor required to turn the probe through 37.0° about its central axis is Number 0.042 Units rev .
To calculate the number of revolutions of the rotor required to turn the probe through 37.0° about its central axis, we can use the concept of rotational motion and the relationship between angular displacement and rotational inertia.
The formula for the angular displacement (θ) in terms of rotational inertia (I) and the number of revolutions (N) is given by:
θ = 2πN
We want to find the number of revolutions N, so we can rearrange the formula as:
N = θ / (2π)
It is given that Angular displacement (θ) = 37.0° = 37.0 * (2π / 360) rad and Rotational inertia of the probe (lₚ) = 10.9 kg·m²
Substituting the values into the formula:
N = (37.0 * (2π / 360)) rad / (2π)
N = 0.042 revolutions.
Therefore, the number of revolutions of the rotor required to turn the probe through 37.0° about its central axis is approximately 0.042 revolutions.
To learn more about inertia: https://brainly.com/question/1140505
#SPJ11
Wieker the right circumstances. in the phocoelectric nstect when light whines upon a metal what is niveted fepm the thetalt Quarbs amt exifecol Eikecturns are ermited DYatoms are enitted. Fhotont are emitted: Question 8 Whicir of the following is NOT an experimental observation of the photoelectric effect? Photoelectrons can be emitted at any brightness of the light used. Light of any frequency above a threshold frequency can produce photoeiectrons: There is a maximum kinetic energy of the photoelectrons that is the same no matter wilat frequency of the light is used. Every material has a different amount of minimam energy needed to produce photoelectrons.
The following is not an experimental observation of the photoelectric effect:Photoelectrons can be emitted at any brightness of the light used.What is the Photoelectric Effect?
The photoelectric effect is a phenomenon in which electrons are emitted from a metal's surface when light shines on it. It's an example of the particle-wave duality of light. It's a quantum process that occurs when photons of a specific energy (or frequency) hit the surface of a metal, causing electrons to be ejected. The photoelectric effect's observations are based on the following:Light of any frequency above a threshold frequency can produce photoelectrons.
Every material has a different amount of minimum energy needed to produce photoelectrons.There is a maximum kinetic energy of the photoelectrons that is the same no matter what frequency of the light is used. Therefore, the correct option is A. Photoelectrons can be emitted at any brightness of the light used.
Learn more about photoelectric effect here,
https://brainly.com/question/1359033
#SPJ11
An inductor of L=8.15H with negligible resistance is placed in series with a E=15.3 V battery, a R=3.00Ω resistor, and a switch. The switch is closed at time t=0 seconds. Calculate the initial current at t=0 seconds. I(t=0 s)= A Calculate the current as time approaches infinity. I max
= Calculate the current at a time of 2.17 s. I(t=2.17 s)= A Determine how long it takes for the current to reach half of its maximum.
Tt takes 2.07 seconds for the current to reach half of its maximum.
Given data:
L = 8.15 H Battery voltage, E = 15.3 VR = 3.00 Ω
From the given data, the initial current (I) flowing through the circuit at the time, t = 0 can be calculated using the equation for inductor in series with a resistor.I = E / (R + L di/dt)
Here, R = 3.00 Ω, L = 8.15 H, E = 15.3 V and t = 0 seconds∴ I (t = 0 s) = E / (R + L di/dt) = 15.3 / (3.00 + 8.15*0) = 15.3 / 3.00 = 5.1 A
The initial current (I) at t = 0 seconds is 5.1 A. The current through the circuit as the time approaches infinity, Imax is given by; I(max) = E / R = 15.3 / 3.00 = 5.1 A
Therefore, the current as the time approaches infinity is 5.1 A. The current at a time of 2.17 seconds can be calculated by the equation; I = I(max)(1 - e ^(-t/(L/R)))Here, L/R = τ is called the time constant of the circuit, and e is the base of the natural logarithm, ∴ I(t = 2.17 s) = I(max)(1 - e^(-2.17/τ)) = I(max)(1 - 1 - [tex]e^{-2.17/(L/R)}[/tex]) = I(max)(1 -[tex]e^{(-2.17/(8.15/3))}[/tex] ) = 5.1(1 - [tex]e^{-0.844}[/tex]) = 2.11 A
Therefore, the current at a time of 2.17 seconds is 2.11 A. The time taken for the current to reach half of its maximum can be calculated by the equation for current; I = I(max)(1 - [tex]e^{-t/(L/R)}[/tex])
Here, when I = I(max)/2, t = τ/ln(2), where ln(2) is the natural logarithm of 2.∴ t = τ/ln(2) = (L/R)ln(2) = (8.15/3)ln(2) = 2.07 s
Therefore, it takes 2.07 seconds for the current to reach half of its maximum.
To learn about current here:
https://brainly.com/question/1100341
#SPJ11
Double-Slit
(a) A double-slit experiment is set up using red light (λ = 717 nm). A first order bright fringe is seen at a given location on a screen. What wavelength of visible light (between 380 nm and 750 nm) would produce a dark fringe at the identical location on the screen? λ = ______________ nm HELP: Find the expression for a first order bright fringe (of a double slit experiment). Then find the expression for dark fringes. (b) A new experiment is created with the screen at a distance of 2.2 m from the slits (with spacing 0.08 mm). What is the distance between the second order bright fringe of light with λ = 689 nm and the third order bright fringe of light with λ = 413 nm? (Give the absolute value of the smallest possible distance between these two fringes: the distance between bright fringes on the same side of the central bright fringe.) |x| = _____________ m
A double-slit experiment is set up using red light (λ = 717 nm). A first order bright fringe is seen at a given location on a screen.
The expression for a first order bright fringe in a double-slit experiment is given as,
Y= (λL)/d where Y is the distance between the central bright fringe and the first-order bright fringe, λ is the wavelength of light, L is the distance between the double-slit and the screen and d is the distance between the two slits.
From the above expression, we can calculate the value of d as, d= (λL)/Y
We are given that a first-order bright fringe is seen at a given location on a screen when the double-slit experiment is set up using red light with a wavelength of 717 nm. So the value of d for this experiment will be,
d = (λL)/Y = (717 x 10^-9 m x L)/Y where L is the distance between the double-slit and the screen.
Now we need to find the wavelength of visible light that would produce a dark fringe at the identical location on the screen.
The expression for dark fringes in the double-slit experiment is given as, d sin θ = (m+1/2) λ where d is the distance between the two slits, θ is the angle of diffraction, m is the order of the fringe and λ is the wavelength of light. From the above expression, we can calculate the value of θ for the dark fringe as,
θ= sin^-1(m+1/2)(λ/d)
For the same location on the screen, we know that the distance between the central bright fringe and the first-order dark fringe will be equal to the distance between the central bright fringe and the second-order bright fringe. So, the value of m for the first-order dark fringe will be equal to 1+2=3. Therefore, the value of θ for the first-order dark fringe will be,
θ= sin^-1(3+1/2)(λ/d)
Also, we know that sinθ ≈ θ for small angles and thus sinθ can be written as θ. Hence, we can write,
θ= (3+1/2)(λ/d)
Substituting the value of d from the expression derived earlier, we get,
θ= (3+1/2)(717 x 10^-9 m x L)/Y
Let λ' be the wavelength of light that would produce a dark fringe at the identical location on the screen. For the same location on the screen, we know that the distance between the central bright fringe and the first-order bright fringe will be equal to the distance between the central bright fringe and the first-order dark fringe. So the value of Y for the first-order dark fringe can be written as,
Y = (λ'L)/d = (λL)/Y
From the above two equations, we can obtain the value of λ',
λ' = (Yλ^2)/(Ld) = (Yλ^2)/(717 x 10^-9 m x L)
λ' = (Y x 717 x 10^-9 m)/Ld
Substituting the given values, we get,
λ' = (Y x 717 x 10^-9 m)/(2.2 m x 0.08 x 10^-3 m)
λ' = 25.98 x Y x 10^-6 m b)
The expression for the distance between two consecutive bright fringes in the double-slit experiment is given as,
Δy = λL/d. For the same side of the central bright fringe, the second-order bright fringe of light with λ = 689 nm and the third-order bright fringe of light with λ = 413 nm will be located at a distance of Δy from each other.
So, Δy = λ1 L/d - λ2 L/d
Δy = (λ1 - λ2)L/d Where λ1 and λ2 are the wavelengths of light and L is the distance between the double-slit and the screen. Substituting the given values, we get,
Δy = (689 - 413) x 10^-9 m x 2.2 m/0.08 x 10^-3 m
Δy = 47.52 x 10^-6 m
The absolute value of the smallest possible distance between these two fringes will be equal to Δy. Therefore, |x| = Δy = 47.52 x 10^-6 m
Learn more about the double-slit experiment: https://brainly.com/question/15715225
#SPJ11