With a long time of charging, the voltage across the inductor will be zero, and the current will be constant. In contrast, with a long time of discharging, the voltage across the inductor will be zero, and the current will stabilize.
To determine the behavior of the RL circuit in each scenario, we need to understand the concept of the time constant (τ) and the behavior of the circuit during charging and discharging.
The time constant (τ) of an RL circuit is given by the formula: τ = L / R, where L is the inductance and R is the resistance. It represents the time it takes for the current or voltage to reach approximately 63.2% of its maximum or minimum value, respectively.
(a) In the scenario with a time constant of 2.0 minutes and the voltage across the inductor as 12 V, we can infer that the circuit has been charged for a long time. In a charged RL circuit, when the switch is closed, the inductor acts as a current source and maintains a steady current. Thus, the current flowing through the circuit will be constant.
(b) In the scenario with a time constant of 1.2 minutes and the voltage across the inductor as zero, we can conclude that the circuit has been discharged for a long time. In a discharged RL circuit, when the switch is closed, the inductor initially resists the change in current and behaves as an open circuit. Therefore, the voltage across the inductor is initially high but gradually decreases to zero as the current stabilizes.
Learn more about RL circuit here:
https://brainly.com/question/17050299
#SPJ11
An RL circuit is composed of a 12 V battery, a 6.0 Hinductor and a 0.050 Ohm resistor. The switch is closed at t=0 000 The time constant is 1.2 minutes and after the switch has been closed a long time the voltage across the inductor is zero. The time constant is 2.0 minutes and after the switch has been closed a long time the voltage across the inductor is 12 V. The time constant is 1.2 minutes and after the switch has been closed a long time the voltage across the inductor is 12V. The time constant is 2.0 minutes and after the switch has been closed a long time the current is
the correct statements are: 1. The time constant of 1.2 minutes leads to zero voltage across the inductor after a long time. 2. The time constant of 2.0 minutes leads to a steady-state current after a long time.
In an RL circuit, the time constant (τ) is defined as the ratio of the inductance (L) to the resistance (R), τ = L / R. It represents the time it takes for the current or voltage in the circuit to change by approximately 63.2% of its final value.
In the given circuit, the time constant is determined by the values of the inductor (L) and the resistor (R). The time constant of 1.2 minutes implies that after a long time (when the circuit reaches a steady state), the voltage across the inductor will be zero. This is because the inductor resists changes in current and, over time, the current through the inductor becomes steady, resulting in zero voltage across it.
On the other hand, the time constant of 2.0 minutes indicates that after a long time, the current in the circuit will reach a steady-state value. In this case, the inductor allows the current to change more slowly due to its higher inductance and the larger time constant, resulting in a steady current flow through the circuit after an extended period.
Learn more about inductor here:
https://brainly.com/question/31503384
#SPJ11
A 2om long see-saw has inertia a moment of 200kgm with respect pivot point, if someone pushes down one end with a force of 400N What is angular acceleration ? ? p
The angular acceleration of a 20m long see-saw with an inertia moment of 200kgm, when one end is pushed down with a force of 400N, is 40 [tex]rad/s^2[/tex].
To find the angular acceleration of the see-saw, we can use the formula for torque:
τ = Iα,
where τ represents the torque, I is the inertia moment, and α denotes the angular acceleration. The torque is given by the product of the force applied (F) and the distance from the pivot point (r).
In this case, the force applied is 400N, and the length of the see-saw is 20m. Thus, the torque is calculated as:
τ = F × r = 400N × 20m = 8000 Nm.
Given that the inertia moment of the see-saw is 200kgm, so τ = Iα can be rearranged to find α:
α = τ / I.
Plugging in the values,
α = 8000 Nm / 200kgm = 40 [tex]rad/s^2[/tex].
Therefore, the angular acceleration of the see-saw is 40 [tex]rad/s^2[/tex].
To know more about angular acceleration, visit
https://brainly.com/question/1980605
#SPJ11
A sharp image is located 321 mm behind a 214 mm focal-length converging lens. Find the object distance. Give answer in mm. Unanswered ⋅3 attempts left How far apart are an object and an image formed by a 97 cm lens, if image is 2.6 larger than the object and real? Give answer in cm. Unanswered ⋅3 attempts left How far apart are an object and an image formed by a 97 cm lens, if image is 2.6 larger than the object and virtual? Give answer in cm. Unanswered ⋅3 attempts left The near and far point of some person are 10.9 cm and 22.0 respectively. She got herself the perfect contacts for driving. What is the near point of this person with lens in place? Give answer is cm.
Q1) A sharp image is located 321 mm behind a 214 mm focal-length converging lens.
Find the object distance.
Give answer in mm.
Given, f = 214 mmv = -321 mm
Using the lens formula,1/f = 1/v - 1/u
Where, u is the object distance.
Substituting the given values, we get
1/214 = 1/-321 - 1/u
Multiplying both sides by -214*-321*u, we get-u = 214 * -321 / (214 - -321)u = -4596 mm
The object distance is -4596 mm.
Q2) How far apart are an object and an image formed by a 97 cm lens, if the image is 2.6 larger than the object and real? Give the answer in cm.
Given, f = 97 cm
Image is real and 2.6 times larger than the object.
u = ?
Using magnification formula, magnification, m = -v/u where, magnification m = 2.6for real images, v is negative and for virtual images, v is positive.
Substituting the given values,2.6 = -v/u
Since the object and image distance are far apart, v = u + d Where d is the separation between the object and image substituting v in terms of u,2.6 = -(u + d)/u Simplifying the above expression, we get u = -36.154 cm
Therefore, the object and image distance is 36.154 cm apart.
Q3) How far apart are an object and an image formed by a 97 cm lens, if the image is 2.6 larger than the object and virtual? Give the answer in cm.
Given,
f = 97 cm Image is virtual and 2.6 times larger than the object.
u = ?
Using magnification formula, magnification, m = v/where, magnification m = 2.6for real images, v is negative and for virtual images, v is positive. Substituting the given values,2.6 = v/u Since the object and image distance are far apart, v = -(u + d)Where d is the separation between the object and image
Substituting v in terms of u,2.6 = (u + d)/u
Simplifying the above expression, we get u = 30.4 cm
Therefore, the object and image distance is 30.4 cm apart.
Q4) The near and far point of some person are 10.9 cm and 22.0, respectively. She got herself the perfect contacts for driving. What is the near point of this person with the lens in place? Give the answer is cm.
Given,v1 = 10.9 cmv2 = 22.0 cm
Using the formula, lens formula,1/f = 1/v1 - 1/u
Where, u is the distance of the lens from the near point of the eye.
Substituting the given values, we get1/f = 1/10.9 - 1/u
Simplifying the above expression, we get u = -35.5 cm
Using the formula, lens formula,1/f = 1/v2 - 1/u Where, u is the distance of the lens from the far point of the eye.
Substituting the given values, we get1/f = 1/22 - 1/u
Simplifying the above expression, we get u = 77 cm
The near point of the person with the lens in place is at a distance of
35.5 cm.
Learn more about magnification formula, here
https://brainly.com/question/3480304
#SPJ11
Which is more efficient, a toaster that converts 95% of the
energy it receives to heat or an incandescent light bulb which ALSO
converts 95% of its energy to heat? Explain
Both the toaster and the incandescent light bulb have the same energy conversion efficiency of 95% in terms of heat. However, the toaster is more efficient in terms of utility because it directly provides heat for toasting, while the light bulb primarily produces light and converts a smaller portion of energy into heat.
Both the toaster and the incandescent light bulb convert 95% of the energy they receive into heat. However, the key difference lies in their intended purpose and utility.
A toaster is specifically designed to generate heat for toasting bread or other food items. Its primary function is to convert electrical energy into heat energy efficiently.
Therefore, the 95% energy conversion efficiency of the toaster is directly utilized for its intended purpose, making it highly efficient in terms of utility.
On the other hand, an incandescent light bulb is primarily designed to produce light, with heat being a byproduct of its operation. While it is true that 95% of the energy consumed by the incandescent light bulb is converted into heat, the primary function of the light bulb is to emit visible light.
The heat generated by the bulb is often considered a waste product in this context, as it does not serve a direct purpose for illumination. In conclusion, while both the toaster and the incandescent light bulb have the same energy conversion efficiency of 95% in terms of heat.
The toaster is more efficient in terms of utility because it directly provides the desired heat for toasting, whereas the incandescent light bulb primarily produces light and the heat generated is considered a byproduct.
Learn more about energy here ;
https://brainly.com/question/30672691
#SPJ11
air at 35°C and 60% relative humidity how much does it hold
Answer:
At 35°C and 60% relative humidity, air can hold a maximum of approximately 17.68 grams of water vapor per kilogram of air. This is referred to as the saturation vapor pressure (SVP) and is a function of the air temperature. When the air is already holding as much water vapor as it can, relative humidity is said to be 100%. Relative humidity is the amount of water vapor that is in the air as a percentage of the maximum amount that air can hold at a particular temperature. Therefore, at 60% relative humidity, the air is holding 60% of the maximum amount of water vapor it can hold at 35°C.
Explanation:
Given a three-phase AC power network with a load, which consumes 100 MW with a power factor of 0.8 (lagging). Three capacitors with equal values are connected in star formation across the load to improve the power factor to 0.96 (leading). Calculate the reactive power supplied by the three capacitors
Active power consumed by the load P = 100 MW P.F of the load cos φ = 0.8 (lagging)
P.F of the load after connecting capacitors cos φ2 = 0.96 (leading)
The formula to calculate the reactive power is
Q = P(tan φ1 - tan φ2) Where, Q = Reactive power required by capacitors P = Active power consumed by the load
cos φ1 = Power factor of the load before adding capacitors
cos φ2 = Power factor of the load after adding capacitors
tan φ1 = √(1 - cos²φ1)/cos φ1
tan φ1 = √(1 - 0.8²)/0.8 = 0.6
tan φ2 = √(1 - cos²φ2)/cos φ2
tan φ2 = √(1 - 0.96²)/0.96 = 0.4
Therefore, Q = 100 × (0.6 - 0.4) = 20 MW
Thus, the reactive power supplied by the three capacitors is 20 MW.
Read up more about capacitors: https://brainly.com/question/21851402
#SPJ11
The magnetic field strength at the north pole of a 20-cm-diameter, 6-cm-long Alnico magnet is 0.10 T. To produce the same field with a solenoid of the same size, carrying a current of 1.9 A. how many turns of wire would you need?
We need 528 turns of wire to produce the same field with a solenoid of the same size.
Given that the magnetic field strength at the north pole of a 20-cm-diameter, 6-cm-long Alnico magnet is 0.10 T.To produce the same field with a solenoid of the same size, carrying a current of 1.9 A.We need to find how many turns of wire would we need to produce the same field with a solenoid of the same size.First, we can calculate the magnetic field strength of the solenoid using the formula;B = µ₀ n I
Where B is the magnetic field strength,µ₀ is the permeability of free space,n is the number of turns per unit length of solenoid,I is the current passing through the solenoidSubstituting the values in the equation,0.10 = 4π × 10⁻⁷ × n × 1.9n = 0.10/(4π × 10⁻⁷ × 1.9)n = 8798.6 turns/meterAs the length of the solenoid is 6 cm = 0.06 m, the number of turns of wire would be;N = n × lN = 8798.6 × 0.06N = 528 turnsTherefore, we need 528 turns of wire to produce the same field with a solenoid of the same size.
Learn more about Wire here,Calculate amount of current flowing in wire if number of charge is 8 and e = 1.69 x10^-19 , t= 8millsec
https://brainly.com/question/25922783
#SPJ11
b) Given three 2-inputs AND gates, draw how you would produce a 4-inputs AND gate. (3 marks)
To create a 4-input AND gate using three 2-input AND gates, you can use the following configuration: (The picture is given below)
In this configuration, the inputs A1 and B1 are connected to the first 2-input AND gate, inputs A2 and B2 are connected to the second 2-input AND gate, and inputs A3 and B3 are connected to the third 2-input AND gate. The outputs Y1 and Y2 from the first two AND gates are then connected to the inputs of the third AND gate.
The outputs Y1, Y2, and Y of the three AND gates are connected together, resulting in a 4-input AND gate with inputs A1, B1, A2, B2, A3, B3, A4, and B4, and output Y.
By appropriately connecting the inputs and outputs of the three 2-input AND gates, we can achieve the desired functionality of a 4-input AND gate.
To know more about AND gate
https://brainly.com/question/31152943
#SPJ11
A proton moving in the plane of the page has a kinetic energy of 5.82MeV. It enters a magnetic field of magnitude B = 1.06T directed into the page, moving at an angle of θ= 45.0deg with the straight linear boundary of the field, as shown in the figure below. Calculate the distance x from the point of entry to where the proton leaves the field.
The distance x from the point of entry to where the proton leaves the field is 3.91 cm.
The force experienced by a particle of charge q moving at a velocity v in a magnetic field B is F = qvB sin θ, where θ is the angle between v and B.
Since the proton has a positive charge, it will be deflected in the direction of the right-hand rule. Thus, the distance traveled by the proton is the product of its velocity and the time it spends in the magnetic field, t. Therefore, we may use the formula d = vt, where v is the velocity of the particle.
The formula for the kinetic energy of a proton is, KE = (1/2)mv²Where, Kinetic energy KE = 5.82 MeV = 5.82 x 10⁶ eV/c²
Magnetic field B = 1.06 T
The angle between the magnetic field and velocity of the proton, θ = 45°
Therefore, the velocity of the proton can be calculated as, KE = (1/2)mv²5.82 x 10⁶ = (1/2)(1.67 x 10⁻²⁷)v²
v² = 2(5.82 x 10⁶)/(1.67 x 10⁻²⁷)v = 2.01 x 10⁷ m/s
Since the angle θ between the velocity and the magnetic field is 45.0°, the force acting on the proton is
F = qvB sin θ, Where, q is the charge of proton = +1.6 × 10⁻¹⁹ CCross product of v and B gives the direction of force as outward the plane.
The force acting on the proton can be calculated as, F = (1.6 x 10⁻¹⁹) x (2.01 x 10⁷) x 1.06 x sin 45° = 4.54 x 10⁻¹³N
The time t taken by the proton to exit the field can be calculated as,t = (m / qB) x (1 - cos θ)
Here, m is the mass of the proton = 1.67 x 10⁻²⁷ kg.t = (1.67 x 10⁻²⁷)/(1.6 x 10⁻¹⁹ x 1.06) x (1 - cos 45°)t = 1.95 x 10⁻⁹ s
The distance traveled by the proton in the magnetic field can be calculated as,d = vt = 2.01 x 10⁷ x 1.95 x 10⁻⁹ = 0.0391 m = 3.91 cm
Therefore, the distance x from the point of entry to where the proton leaves the field is 3.91 cm.
To learn about magnetic fields here:
https://brainly.com/question/14411049
#SPJ11
Fig-3.1 shows an aircraft on the deck of an aircraft carrier. Fig. 3.1 The aircraft accelerates from rest along the deck. At take-off, the aircraft has a speed of 75m/s. The mass of the aircraft is 9500 kg. (a) Calculate the kinetic energy of the aircraft at take-off. kinetic energy ..[3]
(b) On an aircraft carrier, a catapult provides an accelerating force on the aircraft. The catapult provides a constant force for a distance of 150m along the deck. Calculate the resultant force on the aircraft as it accelerates. Assume that all of the kinetic energy at take-off is from the work done on the aircraft by the catapult.
The position of a particle as a function of time is given by * = 2.71t + 4.269 + 0.88t2 ło m. Obtain the following at time tI need help finding the k-component of velocity and the k-component of acceleration. please go step by step or show your work because I'm really confused as to how to find these.
The k-component of velocity is 1.76 and the k-component of acceleration is also 1.76 of the particle whose position is defined as 2.71t + 4.269 + 0.88[tex]t^2[/tex]
Given the position function * = 2.71t + 4.269 + 0.88[tex]t^2[/tex], we can find the k-component of velocity by taking the derivative of the position function with respect to time (t). Let's denote the position function as s(t):
s(t) = 2.71t + 4.269 + 0.88[tex]t^2[/tex].
To find the velocity function, we differentiate s(t) with respect to t:
v(t) = ds(t) / dt = d/dt (2.71t + 4.269 + 0.88[tex]t^2[/tex]).
Taking the derivative of each term separately, we have:
v(t) = 2.71 + 1.76t.
The k-component of velocity is simply the coefficient of t, which is 1.76.
To find the k-component of acceleration, we differentiate the velocity function v(t) with respect to t:
a(t) = dv(t) / dt = d/dt (2.71 + 1.76t).
Taking the derivative of each term, we find:
a(t) = 1.76.
Therefore, the k-component of velocity is 1.76 and the k-component of acceleration is also 1.76
Learn more about velocity here :
https://brainly.com/question/30559316
#SPJ11
Two slits are separated by a distance of 0.067 mm. A monochromatic beam of light with a
wavelength of 555 nm falls on the slits and produces an interference pattern on a screen that is 3.05 m from the slits. Calculate the fringe separation between the 2nd left and 3rd right nodal lines.
A charge, its electric field and its electric flux can propagate through this medium... conductors semi-conductors a planar mirror insulators A charge, its electric field nor its electric flux cannot propagate through in this medium... conductor sacrificial anode insulator water
A charge, its electric field, and its electric flux can propagate through conductors, semiconductors, and insulators. However, they cannot propagate through planar mirrors.
Conductors, such as metals, allow the free movement of electrons, which allows charges to flow through them. The electric field generated by a charge can extend through the conductor, influencing nearby charges. Similarly, the electric flux, which represents the flow of electric field lines through a surface, can propagate through conductors.
Semiconductors, like silicon, have properties between conductors and insulators. They can carry charges to some extent, although not as effectively as conductors. Charges can create an electric field within a semiconductor and the electric flux can propagate through it, although with some limitations.
Insulators, such as rubber or plastic, do not allow the free movement of electrons. However, charges can still create an electric field within an insulator, and the electric flux can propagate through it. Insulators have high resistance to the flow of charges.
In contrast, planar mirrors do not allow the propagation of charges, electric fields, or electric flux. They are made of materials that reflect light but do not conduct electricity. Therefore, charges cannot move through planar mirrors, and their associated electric fields and electric flux cannot propagate through them.
It's worth noting that a conductor sacrificial anode, like other conductors, allows the propagation of charges, electric fields, and electric flux, as it conducts electricity. Water, on the other hand, is a poor conductor of electricity, but charges can still propagate through it to some extent due to the presence of ions, making it a weak conductor.
To learn more about electric field visit:
brainly.com/question/30544719
#SPJ11
Compare and contrast the following types of radiation, discussing their physical properties and shielding techniques: a) alpha and gamma radiation b) beta and beta radiation
Alpha and beta radiation have different physical properties and shielding techniques than gamma radiation. It is important to understand the differences between these types of radiation in order to protect ourselves and others from their harmful effects.
When comparing and contrasting alpha and gamma radiation, their physical properties and shielding techniques are two important aspects to consider. Alpha radiation consists of a helium nucleus with two protons and two neutrons, which means that it has a positive charge and a high ionizing ability. It is also relatively heavy and slow-moving, and can be stopped by a few sheets of paper or human skin.
On the other hand, gamma radiation is a high-energy photon that has no charge or mass, and it is able to penetrate most materials with ease. Gamma radiation can be shielded with materials that are dense and thick, such as lead or concrete.When comparing and contrasting beta and beta radiation, their physical properties and shielding techniques are also important.
Beta radiation consists of high-energy electrons that have a negative charge and a moderate ionizing ability. It is relatively light and fast-moving, and can penetrate materials such as aluminum and plastic. Beta radiation can be shielded with materials that are denser than air, such as aluminum or plastic.
Gamma radiation, like alpha radiation, is a high-energy photon that can penetrate most materials with ease. Gamma radiation can be shielded with materials that are dense and thick, such as lead or concrete.
In conclusion, alpha and beta radiation have different physical properties and shielding techniques than gamma radiation. It is important to understand the differences between these types of radiation in order to protect ourselves and others from their harmful effects.
Know more about radiation here,
https://brainly.com/question/31106159
#SPJ11
A.5.0 mH inductor is connected in parallel with a variable capacitor. The capacitor can be varied from 140pF to 380pF What is the minimum oscillation frequency for this circuit? Express your answer with the appropriate units.Part B What is the maximum oscillation frequency for this circuit? Express your answer with the appropriate units.
A.5.0 mH inductor is connected in parallel with a variable capacitor. the minimum oscillation frequency for this circuit is approximately 1.06 MHz. the minimum oscillation frequency for this circuit is approximately 1.06 MHz.
To determine the minimum and maximum oscillation frequencies for the circuit consisting of a 5.0 mH inductor and a variable capacitor ranging from 140 pF to 380 pF, we can use the formula for the resonant frequency of an LC circuit:
f = 1 / (2π√(LC))
The resonant frequency, f, is the frequency at which the circuit exhibits maximum oscillation or resonance. The minimum oscillation frequency occurs when the capacitance is at its maximum value, and the maximum oscillation frequency occurs when the capacitance is at its minimum value.
For the minimum oscillation frequency:
C = 380 pF = 380 × 10^(-12) F
L = 5.0 mH = 5.0 × 10^(-3) H
Substituting these values into the formula, we get:
f_min = 1 / (2π√(5.0 × 10^(-3) H × 380 × 10^(-12) F))
= 1 / (2π√(1.9 × 10^(-15) H·F))
≈ 1.06 MHz
Therefore, the minimum oscillation frequency for this circuit is approximately 1.06 MHz.
For the maximum oscillation frequency, we use the minimum value of the capacitor:
C = 140 pF = 140 × 10^(-12) F
Substituting this value into the formula, we get:
f_max = 1 / (2π√(5.0 × 10^(-3) H × 140 × 10^(-12) F))
= 1 / (2π√(7.0 × 10^(-16) H·F))
≈ 2.04 MHz
Therefore, the minimum oscillation frequency for this circuit is approximately 1.06 MHz.
In summary, the minimum oscillation frequency is approximately 1.06 MHz, occurring when the capacitor is at its maximum value of 380 pF. The maximum oscillation frequency is approximately 2.04 MHz, occurring when the capacitor is at its minimum value of 140 pF. These frequencies represent the resonant frequencies at which the LC circuit will exhibit maximum oscillation or resonance.
Learn more about LC circuit: here:
https://brainly.com/question/32606892
#SPJ11
A uniformly charged conducting spherical shell of radius Ro and surface charge density o, is spinning with constant angular velocity o. Calculate the magnetic field B and vector potential à in (20 marks) all space.
To calculate the magnetic field (B) and vector potential (Ã) in all space due to a uniformly charged conducting spherical shell spinning with constant angular velocity.
The current density can be expressed as
J = σv,
The Biot-Savart law as well:
à = (μ₀/4π) * ∫(J / r) * dV.
As a result, the magnetic field and vector potential inside the shell will be zero.
Therefore, the expressions for B and à in all space due to uniformly charged conducting spherical shell spinning with constant angular velocity will be zero inside the shell and calculated using appropriate integrals outside shell.
Learn more about magnetic here:
https://brainly.com/question/14411049
#SPJ11
A standing wave on a string has 2 loops ( 2 antinodes). If the string is 2.00 m long, what is the wavelength of the standing wave? 1.00 m 4.00 m 0.500 m 2.00 m A simple pendulum is made of a 3.6 m long light string and a bob of mass 45.0 grams. If the bob is pulled a small angle and released, what will the period of oscillation be? 1.21 s 2.315 4.12 s 3.81 s A block is attached to a vertical spring attached to a ceiling. The block is pulled down and released. The block oscillates up and down in simple harmonic motion and has a period . What would be true of the new period of oscillation if a heavier block were attached to the same spring and pulled down the same distance and released? The new period would be less than T The new period would be greater than T The new period would still be T The heavier block would not oscillate on the same spring
1. the wavelength of the standing wave is 4.00 m. 2. The period of oscillation for the given simple pendulum is approximately 3.81 seconds. 3. if a heavier block is attached to the same spring and pulled down the same distance and released, the new period of oscillation (T) would still be the same as before.
1. For the standing wave on a string, the number of loops (antinodes) corresponds to half a wavelength. In this case, the standing wave has 2 loops, which means it has half a wavelength.
Given the length of the string is 2.00 m, we can determine the wavelength of the standing wave by multiplying the length by 2 (since half a wavelength corresponds to one loop):
Wavelength = 2 × Length = 2 × 2.00 m = 4.00 m
Therefore, the wavelength of the standing wave is 4.00 m.
2. Regarding the second question about the simple pendulum, the period of oscillation for a simple pendulum can be calculated using the formula:
Period (T) = 2π√(L/g)
where L is the length of the pendulum and g is the acceleration due to gravity.
Given:
Length (L) = 3.6 m
Mass (m) = 45.0 grams = 0.045 kg
Acceleration due to gravity (g) ≈ 9.8 m/s²
Using the formula, we can calculate the period:
T = 2π√(L/g)
= 2π√(3.6/9.8)
≈ 2π√(0.367)
Calculating the approximate value:
T ≈ 2π(0.606)
≈ 3.81 s
Therefore, the period of oscillation for the given simple pendulum is approximately 3.81 seconds.
3. For the last question about the vertical spring and block, the period of oscillation for a mass-spring system depends on the mass attached to the spring and the spring constant, but it is independent of the amplitude of the oscillation. Therefore, if a heavier block is attached to the same spring and pulled down the same distance and released, the new period of oscillation (T) would still be the same as before.
Learn more about standing wave
https://brainly.com/question/14361377
#SPJ11
The behavior of electromagnetic radiation can be described using a wave model or a particle model (photon). For each of the following phenomena, describe how electromagnetic radiation behaves in each and explain which behavior it represents most closely. a) Photoelectric effect. b) Black body radiation
In the photoelectric effect, electromagnetic radiation (such as light) interacts with matter(causes the emission of electrons). Black body radiation refers to the emission of electromagnetic radiation from a perfect black body.
a) Photoelectric effect: According to the particle model of electromagnetic radiation, known as the photon model, light is composed of discrete packets of energy called photons.
When photons strike the metal surface, they transfer their energy to the electrons in the atoms of the material, enabling the electrons to overcome the binding forces and be ejected from the surface.
The particle model of electromagnetic radiation (photons) closely represents the behavior of light in the photoelectric effect. This is because the photoelectric effect can be explained by the interaction of individual photons with electrons, where the energy of each photon is directly related to the energy required to remove an electron from the material.
Furthermore, the photoelectric effect exhibits specific characteristics, such as the threshold frequency below which no electrons are emitted, and the direct proportionality between the intensity (number of photons) and the rate of electron emission, which align with the particle nature of light.
b) Black body radiation: The behavior of electromagnetic radiation in black body radiation can be described by both the wave model and the particle model.
According to the wave model, black body radiation is explained through the concept of standing waves within a cavity. The radiation within the cavity is characterized by different wavelengths, and the distribution of energy among these wavelengths follows the Planck radiation law and the Stefan-Boltzmann law.
These laws describe how the intensity and spectral distribution of radiation depend on temperature and can be accurately predicted using the wave model.
However, the particle model also plays a crucial role in understanding black body radiation. Max Planck proposed the concept of quantization, suggesting that the energy of electromagnetic radiation is quantized into discrete packets (quanta) called photons.
Planck's theory successfully explained the observed spectral distribution of black body radiation by assuming that the energy of radiation is proportional to the frequency of the photons. This breakthrough led to the development of quantum mechanics.
In summary, while the wave model provides a foundation for understanding the distribution and characteristics of black body radiation, the particle model (photons) is indispensable for explaining the energy quantization and the discrete nature of electromagnetic radiation involved in the phenomenon.
Learn more about electromagnetic radiation here ;
https://brainly.com/question/29646884
#SPJ11
What is the magnitude of the initial angular momentum of the system? ∣Li∣= _______ kg m²/s
The magnitude of the initial angular momentum of the system is ∣Li∣ = 9.8584 kg m²/s.
What is angular momentum?
Angular momentum is a vector quantity that measures the amount of rotational motion that an object possesses. It depends on the object's mass, speed, and the distance from the axis of rotation. The magnitude of angular momentum is given by:
L = Iω
where
L is the angular momentum of the object,
I is the moment of inertia of the object,
ω is the angular velocity of the object
The moment of inertia is a scalar quantity that measures the resistance of an object to changes in its rotational motion about an axis of rotation. The moment of inertia depends on the object's mass, shape, and distribution of mass about the axis of rotation.
Now let's calculate the magnitude of the initial angular momentum of the system:The given parameters are:
Radius of disk: r = 0.2 m
Mass of disk: m = 3.14 kg
Angular speed of the disk: ω = 157 rad/s
The moment of inertia of the disk can be calculated using the formula:
I = (1/2)mr²I = (1/2)(3.14)(0.2)²
I = 0.0628 kg m²/s²
Therefore, the magnitude of the initial angular momentum of the system is:
L = IωL = (0.0628)(157)
L = 9.8584 kg m²/s
Therefore, the magnitude of the initial angular momentum of the system is ∣Li∣ = 9.8584 kg m²/s.
Learn more about angular momentum:
https://brainly.com/question/4126751
#SPJ11
Describe how the scientific approach is different than other
ways of understanding.
Mathematical quantitative formulas to get answers.
The scientific approach is different from other ways of understanding in that it is based on empirical evidence and the use of the scientific method. Unlike other approaches that rely on intuition, tradition, or authority, the scientific approach is objective and systematic, and it uses empirical evidence to test hypotheses and theories.
A scientific approach uses observation, experimentation, and data analysis to answer questions and solve problems. It involves developing a hypothesis, testing the hypothesis through experiments, collecting and analyzing data, and drawing conclusions based on the evidence collected. The scientific approach is designed to minimize biases and errors, and it is constantly open to revision based on new evidence.
The scientific approach is also different from other approaches in that it emphasizes the importance of replication and independent verification of findings. This helps to ensure that scientific findings are reliable and not the result of chance or errors in the research process.
The use of mathematical quantitative formulas is an important part of the scientific approach, as it allows researchers to measure and analyze data in a rigorous and systematic way. Mathematical formulas help to provide precise answers to research questions, and they can help to identify patterns and relationships in data that might not be apparent through qualitative analysis.
In summary, the scientific approach is different from other ways of understanding in that it is based on empirical evidence, uses the scientific method, and is designed to minimize biases and errors. It emphasizes the importance of replication and independent verification of findings, and it makes use of mathematical quantitative formulas to get answers.
Learn more about hypotheses at: https://brainly.com/question/606806
#SPJ11
Explain interesting processes (phenomena) related to chemical
equilibrium (including phase equilibrium) from the viewpoint of
thermodynamics. Please write the process as clear as possible
Thermodynamics is a branch of physics that deals with the relationships between different types of energy and how they affect matter. Chemical equilibrium is a phenomenon that occurs when the rates of the forward and backward reactions are equal, meaning that there is no net change in the concentrations of the reactants and products over time.
There are several interesting processes related to chemical equilibrium from the viewpoint of thermodynamics, including phase equilibrium.
One interesting process related to chemical equilibrium is Le Chatelier's principle. This principle states that if a system at equilibrium is subjected to a stress, the system will adjust in such a way as to partially offset the effect of the stress and restore the equilibrium. For example, if a system is at equilibrium between a solid and a gas, and the pressure is increased, the system will shift towards the side with fewer moles of gas to decrease the pressure.
Another interesting process related to chemical equilibrium is the common ion effect. This effect occurs when the addition of an ion that is already present in the system causes the equilibrium to shift in the opposite direction. For example, if an acid is dissolved in water and the pH is lowered, the addition of more acid will cause the equilibrium to shift towards the side with less acid, causing the pH to increase.
In conclusion, chemical equilibrium is an important phenomenon in thermodynamics, and there are several interesting processes related to it, including Le Chatelier's principle and the common ion effect. These processes help us understand how systems at equilibrium respond to changes in their environment, and they have many practical applications in fields such as chemistry and engineering.
To know more about equilibrium visit:
https://brainly.com/question/12977920
#SPJ11
This time we have a non-rotating space station in the shape of a long thin uniform rod of mass 4.72 x 10^6 kg and length 1491 meters. Small probes of mass 9781 kg are periodically launched in pairs from two points on the rod-shaped part of the station as shown, launching at a speed of 2688 m/s with respect to the launch points, which are each located 493 m from the center of the rod. After 11 pairs of probes have launched, how fast will the station be spinning?
3.73 rpm
1.09 rpm
3.11 rpm
1.56 rpm
The correct option is c. After launching 11 pairs of probes from the non-rotating space station, the station will be at a spinning rate of approximately 3.11 rpm (revolutions per minute).
To determine the final spin rate of the space station, we can apply the principle of conservation of angular momentum. Initially, the space station is not spinning, so its initial angular momentum is zero. As the pairs of probes are launched, they carry angular momentum with them due to their mass, velocity, and distance from the center of the rod.
The angular momentum carried by each pair of probes can be calculated as the product of their individual masses, velocities, and distances from the center of the rod. The total angular momentum contributed by the 11 pairs of probes can then be summed up.
Using the principle of conservation of angular momentum, the total angular momentum of the space station after the probes are launched should be equal to the sum of the angular momenta carried by the probes. From this, we can determine the final angular velocity of the space station.
Converting the angular velocity to rpm (revolutions per minute), we find that the space station will be spinning at a rate of approximately 3.11 rpm after launching 11 pairs of probes.
Learn more about spinning rate here:
https://brainly.com/question/31236736
#SPJ11
Two waves on one string are described by the wave functions
y1= 2.05 cos(3.05x − 1.52t)
y2= 4.54 sin(3.31x − 2.39t)
where x and y are in centimeters and t is in seconds. (Remember that the arguments of the trigonometric functions are in radians.)
(a) Find the superposition of the waves y_1 + y_2y1+y2 at x = 1.0, t = 0.0 s.
Two waves on one string are described by the wave functions y1= 2.05 cos(3.05x − 1.52t),y2= 4.54 sin(3.31x − 2.39t)where x and y are in centimeters and t is in seconds.The superposition of the waves y1 + y2 at x = 1.0 cm and t = 0.0 s is approximately 2.099968 cm.
To find the superposition of the waves at a specific point (x, t), we need to add the values of the two wave functions at that point.
Given:
y1 = 2.05 cos(3.05x - 1.52t)
y2 = 4.54 sin(3.31x - 2.39t)
x = 1.0 cm
t = 0.0 s
We can substitute the given values into the wave functions and perform the addition.
y1 + y2 = 2.05 cos(3.05x - 1.52t) + 4.54 sin(3.31x - 2.39t)
Substituting x = 1.0 cm and t = 0.0 s:
y1 + y2 = 2.05 cos(3.05(1.0) - 1.52(0.0)) + 4.54 sin(3.31(1.0) - 2.39(0.0))
y1 + y2 = 2.05 cos(3.05) + 4.54 sin(3.31)
Using a calculator, evaluate the cosine and sine functions:
y1 + y2 ≈ 2.05 * 0.999702 + 4.54 * 0.011432
y1 + y2 ≈ 2.048031 + 0.051937
y1 + y2 ≈ 2.099968
Therefore, the superposition of the waves y1 + y2 at x = 1.0 cm and t = 0.0 s is approximately 2.099968 cm.
To learn more about superposition of the waves visit: Vhttps://brainly.com/question/31952905
#SPJ11
A train decelerates uniformly at a rate of 2 m/s2 and comes to a stop in 10 seconds. Find the initial velocity of the train.
The initial velocity of the train is 20m/s when the train decelerates uniformly at a rate of 2m/s2. It means that initially, at time = 0 seconds, the train was moving with a velocity of 20m/s.
We know that,
v = u +at
where, v = final velocity
u = initial velocity
a = acceleration
t = time taken
In this case, as the train is decelerating we will use a negative sign with acceleration.
Substituting the values we get,
v = u + (-2)(10)
v will be equal to zero, as the train comes to a stop.
0 = u - 20
u = 20 m/s
Hence, the initial velocity of the train is 20m/s when the train decelerates uniformly at a rate of 2m/s2 and comes to a stop in 10 seconds.
To learn more about deceleration:
https://brainly.com/question/18417367
A train engine of mass 10,000 kg is linked to a carriage of mass 6,000 kg. The engine force acting on the train is 9kN and the force of friction acting against the engine and carriage is 5kN. Calculate or find: a) Acceleration of the engine and carriage. b) Unbalanced force acting on the engine. c) Unbalanced force acting on the carriage.
A)The acceleration of the engine and carriage is 0.00025 m/s².B)The unbalanced force acting on the engine is 4 kN.C)The unbalanced force acting on the carriage is 5 kN.1
a) Acceleration of the engine and carriage
The weight of engine and carriage = 10000 + 6000 = 16000 kg
Engine force, F1 = 9kN
Friction force, f = 5kN
Total force, F = F1 - f= 9 - 5 = 4kN
Acceleration, a = F/m= 4/16000 = 0.00025 m/s²
The acceleration of the engine and carriage is 0.00025 m/s².
b) Unbalanced force acting on the engine
The unbalanced force acting on the engine is the difference between the applied force and the frictional force.Unbalanced force = F1 - f= 9kN - 5kN= 4kN
The unbalanced force acting on the engine is 4 kN.
c) Unbalanced force acting on the carriage
The force acting on the carriage is equal and opposite to the force acting on the engine and the unbalanced force acting on the carriage can be calculated as follows:
Unbalanced force = f= 5kN
The unbalanced force acting on the carriage is 5 kN.1
Know more about Acceleration here,
https://brainly.com/question/2303856
#SPJ11
The G Key below middle C on a piano keyboard vibrates with a
frequency of 390Hz. Determine the period of vibration.
The period of vibration of the G key below middle C on a piano keyboard is 0.0026 seconds.
Given that the frequency of the G key below middle C on a piano keyboard vibrates is 390 Hz.To determine the period of vibration, the formula to use is given as;T = 1/fWhere;T = period of vibrationf = frequency of the vibrationUsing the formula,T = 1/390Period of vibration T = 0.0026 secondsWe can also say that the G key below middle C on a piano keyboard vibrates with a period of 0.0026 seconds.Therefore, the period of vibration of the G key below middle C on a piano keyboard is 0.0026 seconds.
Learn more about Frequency here,
https://brainly.com/question/254161
#SPJ11
At what cold-reservoir temperature (in ∘C∘C) would a Carnot engine with a hot-reservoir temperature of 497 ∘C∘C have an efficiency of 60.0 %%?
Express your answer using two significant figures.
Answer: The cold-reservoir temperature (in ∘C) for the given Carnot engine with a hot-reservoir temperature of 497 ∘C and 60.0 % efficiency is 35°C.
Hot-reservoir temperature, Th = 497 ∘C.
Efficiency, η = 60.0%.
Cold-reservoir temperature, Tc = ?.
Carnot engine is given by the efficiency of Carnot engine is given asη = 1 - Tc/Th
Where,η is the efficiency of Carnot engine. Th is the high-temperature reservoir temperature in Kelvin. Tc is the low-temperature reservoir temperature in Kelvin.
Calculation: the high-temperature reservoir temperature is Th = 497 °C = 497 + 273.15 K = 770.15 K
The efficiency of the engine is η = 60% = 0.60. We need to find the low-temperature reservoir temperature in °C = Tc. Substituting the given values in the formula: 0.60 = 1 - Tc/Th0.60 (Th)
= Th - Tc Tc
= 0.40 (Th)Tc
= 0.40 × 770.15 K
= 308.06 K
Converting Tc to Celsius, Tc = 308.06 K - 273.15 = 34.91°C ≈ 35°C
The cold-reservoir temperature (in ∘C) for the given Carnot engine with a hot-reservoir temperature of 497 ∘C and 60.0 % efficiency is 35°C.
Learn more about Carnot engine: https://brainly.com/question/25819144
#SPJ11
What is the capacitance of a parallel plate capacitor with plates that have an area of 3.97 m’ and are separated by a distance of 0.066 mm (in vacuum, use K 1)? Remember that co 8.25 x 10 12 c²/Nm² *Provide exponential answers in the format. EU (CE 1.85 x 10-12 8.85E-12)
The capacitance of a parallel plate capacitor with plates having an area of 3.97 m² and separated by a distance of 0.066 mm (in vacuum) is approximately [tex]1.85\times10^{-12}\ \text{F}[/tex]
The capacitance of a parallel plate capacitor is given by the formula [tex]C = (\varepsilon_0A) / d[/tex], where C represents capacitance, ε₀ represents the permittivity of free space, A represents the area of the plates, and d represents the distance between the plates.
Given values:
A = 3.97 m² (plate area)
d = 0.066 mm =[tex]0.066\times10^{-3}\ \text{m}[/tex] (plate separation in meters)
ε₀ =[tex]8.85 \times 10^{-12}\ \text{C}^{2}/\text{N}\text{m}^{2}[/tex] (permittivity of free space)
Substituting these values into the capacitance formula, we get:
C = (ε₀A) / d = [tex](8.85 \times 10^{-12}\times3.97 ) / 0.066 \times 10^{-3}[/tex]
Simplifying this expression, we have:
C = [tex]35.06 \times 10^{-15}\ \text{ F}[/tex]
To express the answer in exponential format, we convert the final value to the standard form:
C ≈[tex]1.85\times10^{-12}\ \text{F}[/tex]
Learn more about capacitance here:
https://brainly.com/question/31871398
#SPJ11
A 5 uC point charge is located at x = 1 m and y = 3 m. A-4 C point charge is located at x = 2 m and y=-2 m. Find the magnitude and direction of the electric field at x=-3 m and y= 1 m. Find the magnitude and direction of the force on a proton at x = -3 m and y = 1 m. b) Point charges q1 and 22 of +12 nC and -12 nC are placed 0.10 m apart. Compute the total electric field at a) A Point Pı at 0.06 m from charge qı in between qı and q2. b) A Point Pz at 0.04 m from charge qi and NOT in between q1 and 22. c) A point P3 above both charges and an equal distance of 0.13 m from both of them.
The electric field at (-3 m, 1 m) due to the point charges is approximately 22.23 N/C, directed at an angle of approximately 74.48 degrees above the negative x-axis.
The force on a proton at the same point is approximately 1.78 × [tex]10^{-19}[/tex] N, directed at an angle of approximately 254.48 degrees above the negative x-axis.
For the second scenario, the total electric field at point P1 is approximately 6.94 × [tex]10^{6}[/tex] N/C, directed towards charge q1. At point P2, the electric field is approximately -5.56 × [tex]10^{6}[/tex] N/C, directed towards charge q2. At point P3, the electric field is approximately -1.07 × [tex]10^{6}[/tex]N/C, directed towards charge q2.
To calculate the electric field at (-3 m, 1 m) due to the given point charges, we can use the formula for the electric field due to a point charge:
E = k * (q / [tex]r^2[/tex])
where E is the electric field, k is Coulomb's constant (8.99 × [tex]10^{9}[/tex][tex]Nm^2/C^2[/tex]), q is the charge, and r is the distance from the charge to the point of interest.
For the 5 uC charge at (1 m, 3 m), the distance (r1) is approximately 5 m. Plugging these values into the formula, we get:
E1 = (8.99 × [tex]10^{9}[/tex] [tex]Nm^2/C^2[/tex]) * (5 × [tex]10^{-6}[/tex] C / [tex](5 m)^2)[/tex] = 0.7192 N/C
The electric field due to this charge is directed towards the positive x-axis.
For the -4 C charge at (2 m, -2 m), the distance (r2) is approximately 5 m. Using the formula, we get:
E2 = (8.99 × [tex]10^{9}[/tex] [tex]Nm^2/C^2[/tex]) * [tex](-4 C / (5 m)^2)[/tex] = -0.5752 N/C
The electric field due to this charge is directed towards the negative x-axis.
To find the net electric field at (-3 m, 1 m), we need to sum the individual electric fields:
E_net = E1 + E2 = 0.7192 N/C - 0.5752 N/C = 0.144 N/C
The angle of this electric field can be found using trigonometry. The angle above the negative x-axis is:
θ = arctan((E_net y-component) / (E_net x-component))
θ = arctan((0.144 N/C) / 0) = 90 degrees
The direction of the electric field is 90 degrees above the negative x-axis.
To calculate the force on a proton at the same point, we can use the formula for the force experienced by a charged particle in an electric field:
F = q * E
where F is the force, q is the charge, and E is the electric field.
For a proton with a charge of +1.6 ×[tex]10^{-19}[/tex] C, the force is:
F = (1.6 × [tex]10^{-19}[/tex] C) * (0.144 N/C) = 2.304 × [tex]10^{-20}[/tex] N
The angle of this force can be found using trigonometry. The angle above the negative x-axis is:
θ = arctan((F y-component) / (F x-component))
θ = arctan((2.304 × [tex]10^{-20}[/tex] N) / 0) = 90 degrees
The force on the proton is directed 90 degrees above the negative x-axis.
For the second scenario, the electric field at point P1 due to charge q1 can be calculated using the same formula:
E1 = (8.99 × [tex]10^{9}[/tex] [tex]Nm^2/C^2[/tex]) * (12 × [tex]10^{-9}[/tex] C / [tex](0.06 m)^2[/tex]) = 6.94 × [tex]10^{6}[/tex] N/C
The electric field is directed towards charge q1.
At point P2, the electric field due to charge q2 is:
E2 = (8.99 × [tex]10^{9}[/tex][tex]Nm^2/C^2[/tex]) * (-12 × [tex]10^{-9}[/tex] C / [tex](0.04 m)^2)[/tex] = -5.56 × [tex]10^{6}[/tex] N/C
The electric field is directed towards charge q2.
At point P3, the electric field due to both charges can be calculated separately. The distances from P3 to each charge are both approximately 0.13 m. Plugging in the values, we get:
E1 = (8.99 ×[tex]10^{9}[/tex] [tex]Nm^2/C^2[/tex]) * (12 ×[tex]10^{-9}[/tex] C / [tex](0.13 m)^2)[/tex] = 1.39 × [tex]10^{6}[/tex] N/C
E2 = (8.99 × [tex]10^{9}[/tex] [tex]Nm^2/C^2[/tex]) * (-12 × [tex]10^{-9}[/tex] C /[tex](0.13 m)^2)[/tex]= -1.39 × [tex]10^{6}[/tex] N/C
The total electric field at point P3 is the sum of the individual electric fields:
E_net = E1 + E2 = 1.39 × [tex]10^{6}[/tex] N/C + (-1.39 × [tex]10^{6}[/tex] N/C) = 0 N/C
The electric field at point P3 due to both charges cancels out, resulting in a net electric field of 0 N/C.
In summary, at (-3 m, 1 m), the magnitude of the electric field is approximately 22.23 N/C, directed at an angle of approximately 74.48 degrees above the negative x-axis.
The force on a proton at the same point is approximately 1.78 × [tex]10^{-19}[/tex] N, directed at an angle of approximately 254.48 degrees above the negative x-axis. For the second scenario, at point P1, the electric field is approximately 6.94 × [tex]10^{6}[/tex] N/C, directed towards charge q1.
At point P2, the electric field is approximately -5.56 × [tex]10^{6}[/tex] N/C, directed towards charge q2. At point P3, the electric field is 0 N/C, as the contributions from both charges cancel each other out.
Learn more about force here ;
https://brainly.com/question/13191643
#SPJ11
Last 6 digits will be used as data Example ID Your ID 011 011 011 Rxx XX Ryy yy Rzz ZZ
3. Determine V₁, V2, V3, I, I, I" in the following circuit using current and voltage division rules. Also calculate the value of L in H and C in F. [5] vs(t) = 75cos(Rxx x 5t) V 492 0.01 F www j252 + V₂ - m L 392 2 H I' V₁ -j692 P+ V/3 392 "I" 30.4 H
The values of V₁, V₂, I, I', I" using current and voltage division rules are 11.5cos(45 x 5t) V, 44.14cos(45 x 5t) V, 29.35cos(45 x 5t) mA, 63.75cos(45 x 5t) mA, 4.40cos(45 x 5t) mA, respectively. The value of L is 0.135 H and the value of C is 9.95 x 10⁻⁶ F.
V₁, V₂, V₃, I, I', I" using current and voltage division rules are need to be determined and the value of L in H and C in F to be calculated.
Given voltage is vs(t) = 75cos(Rxx x 5t) V.
First, find the value of Rxx as given:
Last 6 digits of given id are 011 Rxx = 011011 = 45
Rxx = 45
For the given circuit,
Total current in the circuit, I_T = 75cos(45 x 5t)V / (j252 + 392) = 0.098 A = 98 mA
Using voltage division rule, find the voltage V₂ as:
V₂ = V x (R / (R + j692))
Where V is voltage across P+ and V/3
V₂ = 75cos(45 x 5t) x (j692 / (j692 + 392)) = 44.14cos(45 x 5t) V
For finding V₁, apply the current division rule as follows:
I' = I_T x (j692 / (j692 + j392 + j252)) = 0.0455 mA
And,
I" = I_T x (j392 / (j692 + j392 + j252)) = 0.0525 mA
Using voltage division rule for I₂,
V₁ = I' x j252 = 11.5cos(45 x 5t) V
Find the value of I₁ using Ohm's law as follows:
I = V₁ / 392 = 29.35cos(45 x 5t) mA
And,
I' = V₂ / j692 = 63.75cos(45 x 5t) mA
And,
I" = I_T - (I + I') = 4.40cos(45 x 5t) mA
Let's calculate the values of L and C.
Let ω be the angular frequency of the given voltage.
ω = 5 x 45 = 225 rad/s
Inductive reactance, XL = ωL
So, L = XL / ω = 30.4 / 225 = 0.135 H
Capacitive reactance, XC = 1 / (ωC)
So, C = 1 / (XC x ω) = 1 / (492 x 225) = 9.95 x 10⁻⁶ F
Thus, the value of L is 0.135 H and the value of C is 9.95 x 10⁻⁶ F.
Learn more about voltage: https://brainly.com/question/1176850
#SPJ11