The balance between food and energy is necessary. So, cutting out junk food and spending an hour a day exercising is good for health. Hence, option C is correct.
What is Energy?Energy in physics is the capacity to do work. It could take on several shapes, such as potential, kinetic, thermal, electrical, chemical, radioactive, and more. In addition, heat and effort are two other ways that energy is exchanged between bodies.
After being transferred, energy is always recognized according to its nature. As a result, the generation of thermal energy may happen through heat transfer while the formation of mechanical energy may result from work being done.
Hence, from this information Option C is correct.
To get more information about Energy :
https://brainly.com/question/1932868
#SPJ1
Answer:
c. cutting out junk food and spending an hour a day exercising
Explanation:
In which type of circuit must the voltage always be the same across each
resistor/branch.
A: Series Circuit
B: Parallel Circuit
C: Both
If a high tide occurs at 6 A.M. and 6 P.M. At what time will the low tides occur?
The time it takes for the water along the shore to go from high to low and back again is six hours and 12.5 minutes between high tides, which happen every twelve hours and twenty-five minutes.
How long does it take for the tide to change from high to low?
six days, twelve and five minutes
Coastal locations see two high and two low tides every 24 hours and 50 minutes because the Earth spins through two tidal "bulges" every lunar day. There are 12 hours and 25 minutes between high tides. The sea level at the shore can change from high to low or from low to high in six hours and 12.5 minutes.
To learn more about Tides refer to:
https://brainly.com/question/2604305
#SPJ13
State reason why water spilled on glass surface wets the surface
a flatbed truck is carrying a crate along a level road. the coefficient of static friction between the load and the bed is 0.40. the truck accelerates forward and the crate stays in its place on the truck bed. in what direction is the force that the bed exerts on the crate?
The direction is the force that the bed exerts on the crate Forward.
Friction between the track and the crate holds the crate in place and allows the crate to move with the vehicle. As a result, the crate's frictional force is directed north, in the same direction as the truck's velocity. As mentioned earlier, both the horizontal and vertical forces have a magnitude of 0 so there is no net force on the box. Therefore, the force on the box has no direction.
The net force always has the same direction as the acceleration. For an object in a circular motion with constant velocity, the net force is directed toward the center of the circle around which the object is moving. The frictional force acts on a moving object, and its direction is opposite to the direction of movement. As we walk, our feet are pushed backward so friction works in the opposite direction to counteract the push.
Learn more about The truck accelerates here:- https://brainly.com/question/13733826
#SPJ4
NEED HELP URGENTLY FOR 10 POINTS!
Answer:
when he shot a beam of alpha particles at a sheet of gold foil, a few of the particles were deflected. He concluded that a tiny, dense n)ucleus was causing the deflections. SO the 3rd option :)
Explanation:
its like 4 a_m r)n why am i on brainly id_k have a nice day !
rank in order, from largest to smallest, the magnitudes of the horizontal forces f1 , f2 , and f3 acting on the arrows. some may be equal. state your reasoning.
The ranking in order from largest to smallest of the magnitudes of the horizontal forces f1 , f2 , and f3 acting on the arrows is F1=F2=F3>0 because there is no change in the horizontal motion of the arrows.
All three arrows in the scenario have been shot and it is assumed that air resistance can be neglected. With the motion of the arrows in horizontal direction, there is no likely change in the horizontal motion of the three arrows. This makes the three forces equivalent to one another and each force is equal to zero (i.e. F1=F2=F3=0).
Here's the complete question:
Rank in order, from largest to smallest, the magnitudes of the horizontal forces F1, F2, and F3 acting on the arrows. Some may be equal. State your reasoning. Rank in order, from largest to smallest, the magnitudes of the horizontal forces , , and acting on the arrows. Some may be equal. State your reasoning.
a. F3>F1=F2 because the mass of the first arrow is equal to the mass of the second arrow which is less than the mass of the third arrow.
b. F1=F2=F3=0 because there is no change in the horizontal motion of the arrows.
c. F1>F2=F3 because the velocity of the second arrow is equal to the velocity of the third arrow which is less than the velocity of the first arrow.
d. F1=F2=F3>0 because there is no change in the horizontal motion of the arrows.
Learn more on horizontal forces from:
https://brainly.com/question/14285188?referrer=searchResults
#SPJ4
A football player throws a football 30 meters in 2.5 seconds. What is the speed of the ball?A 75 m/sB 12 m/sC 30 m/sD 2.5 m/s
Given,
The distance covered by the football, d=30 m
The time it takes for the football to cover the given distance, t=2.5 s
The speed of an object is given by the ratio of the distance covered by the object to the time it takes for the object to cover that distance.
Thus the speed of the ball is given by,
[tex]s=\frac{d}{t}[/tex]On substituting the known values in the above equation,
[tex]\begin{gathered} s=\frac{30}{2.5} \\ =12\text{ m/s} \end{gathered}[/tex]Thus the speed of the ball is 12 m/s
Therefore the correct answer is option B.
Specific heat capacities are tabulated in units of j/g⋅k, but most temperature measurements are made in units of celsius. If a system is initially at 5°c and is heated to 10°c, what is the change in temperature in kelvins?.
The change in temperature in kelvin, given that the system was heated from 5 °C to 10 °C is 278 K
How to determine the change in temperatuerWe'll begin by obtaining the change in temperature in degree Celsius. This can be obtained as follow:
Initial temperature (T₁) = 5 °CFinal temperature (T₂) = 10 °CChange in temperature (ΔT) =?ΔT = T₂ – T₁
ΔT = 10 – 5
ΔT = 5 °C
Finally, we shall convert 5 °C to unit in kelvin. This can be obtained as follow:
Change in temperature (in °C) = 5 °CChange in temperature (in K) = ?T(K) = T(°C) + 273
T(K) = 5 + 273
T(K) = 278 K
Thus, from the above calculation, we can conclude that the change in temperature is 278 K
Learn more about conversion:
https://brainly.com/question/5684726
#SPJ1
A 10-kg crate sits on a horizontal floor. What is the maximum static friction that could be exerted on the crate? the coefficient of static friction is 0. 60.
The maximum static friction that could be exerted on the crate is 58.8.
Static friction is a force that keeps an object at rest. Friction is experienced when individuals try to move a stationary object on a surface, without actually triggering any relative motion between the body and the surface on which it is on.
Formula for static friction:
Static friction(max) = Normal force × Static friction
= mg × μ
m = mass = 10kg
g = gravity on the body = 9.8 m/s²
μ = static friction = 0.60
Now putting these values in the equation, we get:
Static friction = 10 × 9.8 × 0.60
= 58.8
Therefore the static friction is 58.8.
To know more about static friction refer to the link given below:
https://brainly.com/question/13680415
#SPJ4
the initial velocity of a 2.35 kg block sliding down a frictionless inclined plane is found to be 1.31 m/s. then 1.13 s later, it has a velocity of 5.07 m/s. what is the angle of the plane with respect to the horizontal
mg x sin A calculates the force pushing the mass down the hill. Additionally, this force has the same formula: m x a, where an is the actual acceleration in the plane. By dividing the difference between the two speeds by the provided time, or 5.07 m/s - 1.31 m/s / 1.73 s = 4.34 m/s2, the acceleration a may be calculated.
Ma is therefore equal to mg times sin A, or sin A = a / g, or 4.34 m/s2 times 9.81 m/s2 times 0.439.
A = arc sin(0.439)sin(26.0) =
How is friction defined?Friction is a force that prevents two solid objects from rolling or sliding over one another. Although frictional forces, such the traction required to walk without slipping, may be advantageous, they can provide a significant amount of resistance to motion.
To know more about friction, visit-https://brainly.com/question/13000653
#SPJ4
Calculate the potential energy of a 50 kg diver on board 5 meters above the water
The Potential energy is 2450 J.
Potential energy = mgh
m = mass of an object
g = acceleration due to gravity
h = height of an object where it is placed
Put these values in formula, mgh
Potential energy = mgh
Potential energy = 50×9.8×5
Potential energy = 2450 J
Potential energy is stored energy in an object. Potential energy is the product of mass of an object, acceleration due to gravity and height of an object where it is placed.
The S.I. unit of potential energy is joule and is represented by J.
Learn more about Potential energy here:- https://brainly.com/question/14427111
#SPJ1
hi the picture attached is my question on my homework
ANSWER:
Sphere B
STEP-BY-STEP EXPLANATION:
The time of the air depends on the mass, initial velocity and the height of the object, having the same mass and the same height, it depends only on the initial velocity.
The higher the initial velocity, the shorter the time in the air, therefore in this case the sphere B that has a lower velocity will be the one that will spend the longest time in the air.
an electric motor rotating a workshop grinding wheel at a rate of 103 rev/min is switched off with a constant deceleration of 1.96 rad/s 2 . how long does it take for the grinding wheel to stop? answer in units of s.
5.45 second it will take for the grinding wheel to stop an electric motor rotating a workshop grinding wheel at a rate of 103 rev/min is switched off with a constant deceleration of 1.96 rad/s 2
ω1 = 2π(103/60) = 10.7 rad/s
ω2 = 0
α = -1.96 rad/s^2
time t = (ω2 - ω1)/α
= 10.7 / 1.96
= 5.45s
θ = ω1t + (1/2)αt^2
= 58.31 - 29.12 = 29.21
Generally speaking, deceleration is a decrease in acceleration. When an object's speed decreases with respect to time, it is said to be decelerating. In contrast to acceleration, deceleration involves a negative rate of change in velocity.
To know more about deceleration visit : https://brainly.com/question/4403243
#SPJ4
What is the height a football is
kicked when it leaves the players
foot at 30 m/s in a 29° angle?
Answer:
Vy = V0 * sin θ vertical speed
Vy = 30 m/s * sin 29 = 14.5 m/s
t = 14.5 m/s / 9.8 m/s^2 = 1.48 sec time to reach max height
H = Vy t - 1/2 g t^2 acceleration is in opposite direction to initial Vy
H = 14.5 m/s * 1.48 s - 1/2 * 9.8 m/s^2 * (1.48 s)^2
H = 10.7 m
A 900 kg walrus is swimming at a speed of 35 km/hr. What is its kinetic energy?
A ball rolls down a ramp for 15 seconds. If the initial velocity of the ball was 2.1 m/sec and the final velocity
was 7.3 m/sec, what was the acceleration of the ball?
Answer: a=.347
Explanation: Acceleration can be calculated by subtracting the initial velocity (2.1 m/s) from the final velocity (7.3) and dividing the difference by the time (15s).
[tex]\frac{7.3-2.1}{15} = .347[/tex]
An object weighs 350 N. Find its mass.
Use g = 10 m/s².
Answer:
Explanation:
Given:
F = 350 N
g = 10 m/s²
___________
m - ?
m = F / g = 350 / 10 = 35 kg
A cow wanders 30 m North, turns 22 degrees right of its original path, and wanders another 40 m. Find its total displacement.
Answer:OB=58.3m
Explanation:
So here cow wanders 30m in north and turns 22 degrees in right side and moves 40m more, as shown in figure given.
now take the starting point as a origin such that cow moves in x-y co-ordinate axis.
As shown in figure length OA is the length when cow moves in north or y direction. Later she takes 22 degrees turn to right and moves 40m more.
So the final displacement is the length of cow from the origin that is length OB.
now co-ordinates of B are [40cos22°,40sin22°+30] i.e [37.084,44.984]
now displacement of cow= length of OB
= [tex]\sqrt{[37.084]^{2}+[44.984]^{2} }[/tex]
=[tex]\sqrt{3398.78}[/tex]
OB =[tex]58.3[/tex]
Two runners are racing around a cicular track. The first runner is in the inside lane. The second runner is in the outside lane. If the first runner wants to stay side-by-side with the second runner, what does her angular velocity need to be?.
If the first runner wants to stay side-by-side with the second runner, The angular velocity needs to be the same as they would then cover equal angular distance for a period of time.
An equal angular distance means that it would always be side to side.In order to do this, the first runner needs to run at a faster speed than the second runner. This is because the second runner is running in a larger circle than the first runner, so she covers more ground in the same amount of time. The first runner needs to make up for this by running at a faster speed.
Learn more about Angular velocity at : https://brainly.com/question/9262400
#SPJ4
An atmospheric layer of a specific gas provides shielding from harmful ultraviolet light from the sun, allowing life to thrive on earth. What gas makes up this layer?.
The gas that makes up this layer is Ozone.
The ozone layer protects the earth from most of the sun's UVB rays. Greenhouse gases are a set of gases that accumulate in the lower layer of the atmosphere, the troposphere and absorb infrared radiation to increase the average temperature of the Earth's surface. At the top of the stratosphere, 30 miles up, ozone absorbs most of the sun's harmful UV rays.
At the top of the troposphere 12 miles up, ozone acts as a greenhouse gas and traps heat. The troposphere is the lowest layer of the Earth's atmosphere. Most of the atmospheric mass is in the troposphere. Most types of clouds are in the troposphere, and almost all weather phenomena occur in this layer. Ozone protects the earth's surface from ultraviolet radiation from the sun. The ozone layer reduces the risk of skin cancer.
Learn more about An atmospheric layer here:-https://brainly.com/question/12613495
#SPJ4
A light ray of wavelength 589 nm (produced by a sodium lamp) traveling through air strikes a
smooth, flat slab of crown glass at an angle of 30.0° to the normal.Find the angle of refraction, θr .
The angle of refraction for the light ray with the wavelength of 589nm traveling through air strikes a crown glass at 30.0° incidence is 19.2°.
What is refraction?Refraction is the quantity used to measure the amount of refraction taking place at any boundary when light passes between the two mediums.
Refractive index can be calculated using Snell's law, the formula for calculating angle of refraction is as follows:
n₁/n₂ = sinФ₁/sinФ₂
n₁. sin(i) = n₂. sin(r)
where, n₁ = refractive index of medium 1
n₂ = refractive index of medium 2
i = angle of incidence in air
r = angle of refraction in glass
Therefore, by putting the values in this formula we can get the angle of refraction.
(1) × sin(30°)=(1.52) × sin(r)
sin(r)= 1/2 × 1.52
sin(r) = 1/ 3.04
r = sin⁻¹(0.328)
r = 19.2°
Therefore, Angle of refraction = 19.2°
Learn more about Refraction here:
https://brainly.com/question/14760207
#SPJ1
Your question is incomplete, most probably the complete question is:
A light ray of wavelength 589 nm (produced by a sodium lamp) traveling through air strikes a smooth, flat slab of crown glass at an angle of 30.0 to the normal. If the index of refraction of the crown glass is 1.52 and the index of refraction of air is 1. Find the angle of refraction.
When air expands it and it is warm outside then the air is ________________________
When air expands it is warm outside then the air is contracted and becomes cool.
What is air?The atmosphere of Earth or also known as air is the layer of gases retained by Earth's gravity that surrounds the planet and forms its planetary atmosphere.
When warm air expand, the molecules heat and move faster makin them to move apart. So we know that air expands when heated and contracts when cooled, the reason for that is because there is more space between the molecules, the air is less dense than the surrounding matter and the hot air floats upward.
Atmospheric convection helps us to understand that as air heats up and becomes less dense, it rises higher into the air. As it reaches higher elevations, it encounters less air pressure. The lower air pressure at higher elevations allows the air to expand even more. As this air continues to expand, it begins to cool down.
Learn more about air at: https://brainly.com/question/636295
#SPJ1
What are the characteristics of light?
Explanation:
intensity, direction, color, contrast, hardness
What is Kepler's laws of planetary motion?
Answer:
Kepler's laws of planetarymotion :law of orbit - Every planet moves in an elliptical orbit around the sun, with the sun being at one of the fociilaw of areas - The radius vector drawn from the sun to the planet sweeps out equal areas in equal intervals of time i.e., the areal velocity of a planet is constant law of periods or Harmonic law - The square of the period of revolution (T) of a planet around the sun is proportional to the cube of the semi-major axis r of the ellipse .T² ∝ r³
Hope it's help you :))modulus of oil is 5 * 10 ^ 9 * Pa and its compressibility is 2 * 10 ^ - 5 * at * m ^ 1
Exercise 9: The brass plate of an outdoor sculpture experiences shear forces in an earthquake. The plate is 0.8m ^ 2 and 0.5 cm thick. What is the force exerted on each of its edges if the resulting displacement x is 0.16 mm? (Shear modulus = 3.5 * 10 ^ 10 * Pa )
The force exerted on each of its edges at the given shear stress and area is determined as 2.8 x 10¹⁰ N.
What is force exerted on each plate?The force exerted on each plate is calculated by applying the formula for shear stress as shown below.
Shear stress is the force that tends to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress. Like the name implies, shear stress or forces tends to "shear" object or cause deformation of materials.
F = Aσ
where;
F is the applied A is the area of the surfaceσ is the shear stressSubstitute the given parameters and solve for the force applied to create the shear stress.
F = (0.8 m²) x (3.5 x 10¹⁰ Pa)
F = 2.8 x 10¹⁰ N
Thus, the force exerted on each of its edges resulting in the given displacement increases as the shear stress increases.
Learn more about shear stress here: https://brainly.com/question/20630976
#SPJ1
a capacitor consists of a set of two parallel plates of area ???? separated by a distance ????. this capacitor is connected to a battery that maintains a
The correct answer is option D: halved
Energy becomes half i.e. E' = E/2 if the distance between the plates is doubled.
Let's say the area of parallel plates = A
The distance between plates = d
The potential difference between Plates = V
Now, the capacitance is given by
C = ∈[tex]o[/tex] A / d
If the separation between the plates is doubled then the value of capacitance will become half.
C' = ∈[tex]o[/tex] A / 2d
C' = C/2
Now, we can determine the electrical energy stored in the capacitor which is given by
E = [tex]\frac{1}{2}[/tex] [tex]CV^{2}[/tex]
When the distance between the plates is doubled then energy becomes
E' = [tex]\frac{1}{2}[/tex] x [tex]\frac{C}{2}[/tex] x [tex]V^{2}[/tex]
E' = E/2
Thus, energy becomes half i.e. E' = E/2 if the distance between the plates is doubled.
If you need to learn more about energy click here:
https://brainly.com/question/27438014
#SPJ4
The complete question is:
A capacitor consists of a set of two parallel plates of area A separated by a distance d. This capacitor is connected to a battery that maintains a constant potential difference V across the plates. If the separation between the plates is doubled, the electrical energy stored in the capacitor will be: _______
a- doubled
b- unchanged
c- quadrupled
d- quartered
e- halved
40 kg girl and an 8.4 kg sled are on the frictionless ice of a frozen lake, 15 m apart but connected by a rope of negli- gible mass. the girl exerts a hori- zontal 5.2 n force on the rope. what are the acceleration magni- tudes of (a) the sled and (b) the girl? (c) how far from the girl’
a) The acceleration magnitudes of the sled is 0.62 m/s². b) The acceleration magnitudes of the girl is 0.13m/s². c) The distance from the girl is 2.6m.
(a) The girl's force is the sole horizontal force acting on the sled because friction is insignificant. The total of the vertical forces—gravitational force and the normal force of the ice—is zero. The sled accelerates with an acceleration of
a s = F/m s = 52N/8.4kg = 0.62m/s².
(b) The third law of Newton states that the force exerted by the sled on the girl is 5.2N. Her acceleration is equal to a g times m g.
a s= F/m s = 5.2N/40kg = 0.13m/s².
(c) The sled and girl are accelerating in the opposite directions. The coordinate for the girl, assuming she starts at the origin and advances in the +x direction, is given by x g = 2 1 a g t 2. The sled moves in the -x direction and begins at x 0 = 15m. Its location is indicated by the coordinates x s =x 0 2 1 a s t 2. They collide when x g = x s, or when 2 1 a g t 2 = x 0 2 1 a s t 2.
When this occurs
t= a \sg \s \s +a \ss \s
2x \s0
The girl has already traveled the distance x g = 2 1 a s t 2 = a g + a s by that point.
x \s0 \s \s a \sg
\s = \s0.13m/s \s2 \s +0.62m/s \s2
(15m)(0.13m/s \s2 \s ) \s \s =2.6m
To know more about acceleration click on the link:
https://brainly.com/question/12550364
#SPJ4
Question at position 3
The table shows mass and weight data of some common items.
Based on the data, which conclusion is valid regarding the relationship between the force of gravity, mass, and weight?
The table shows mass and weight data of some common items.
Based on the data, which conclusion is valid regarding the relationship between the force of gravity, mass, and weight?
The weight of an object depends on the force of gravity of the planet, but the mass does not.
Neither the mass nor the weight of an object depends on the force of gravity.
The mass of an object depends on the force of gravity of the planet, but the weight does not.
Both the mass and the weight of an object depend on the force of gravity.
An increase in the distance between the objects causes a greater change in the gravitational force than the same increase in mass. It depends on the object's mass and acceleration due to gravity.
Mass is an intrinsic unchanging property. Weight is a force and it depends on gravitational force. This force is directly proportional to mass the more mass the object has the stronger the force of gravity will be. Because of this, it turns out that gravity does not matter when we compare the distance traveled by objects with different masses. The important part of the force is air resistance also called drag.
The slope of the graph is the relationship between weight and mass. The slope tells how many newtons of weight pull down on each kilogram of mass. Mass is the measure of the amount of matter in an object. This is an immutable property inherent in the body. Mass cannot be destroyed or created. Weight is the production of mass and acceleration due to gravity.
Learn more about Mass here:-https://brainly.com/question/19385703
#SPJ1
a small boat was initially drifting at 0.5 m/s down stream. the person in the boat rolled the oar for 20 s, and the boat ended traveling upstream at 2 m/s. if the boat and person weighs a total of 200 kg, what was the average net force on the small boat during the 20s period?
25 Newton is the average net force on the small boat during the 20s period
initial velocity of boat=0.5m/s
after t= 20s, velocity of boat= -2m/s
acceleration of boat=
[tex]a=v-u/t=-2-0.5/20[/tex]
[tex]a=-0.125m/s^2[/tex]
total weight= 200 kg
average net force= ma
average net force=200×0.125
average net force=25N
In mechanics, a force is any action that seeks to preserve, modify, or deform a body's motion. Isaac Newton's three principles of motion, which are outlined in his Principia Mathematica, are frequently used to illustrate the idea of force (1687).
Newton's first law states that unless a force is applied to a body, it will stay in either its resting or uniformly moving condition along a straight path. According to the second law, when an external force applies on a body, the body accelerates (changes velocity) in the force's direction.
To know more about force visit : https://brainly.com/question/13191643
#SPJ4
one metal object is a cube with edges of cm and a mass of g. a second metal object is a sphere with a radius of cm and a mass of g. are these objects made of the same or different metals? assume the calculated densities are accurate to .
density ρ=mass/volume density accuracy > 1%
cube volume = 27 cm^3&mass = 140.4 g Density =140.4/27=5.2g/cm^3 sphere volume = 12 cm^3&mass= 61.6 g Density =61.6/12=0.133g/cm^3
mass per unit volume of a solid substance; density. Density is defined as d = M/V, where M stands for mass, and V for volume. The unit of density that is most frequently used is grammes per cubic centimetre. For instance, the density of Earth is 5.51 grammes per cubic centimetre, while the density of water is 1 gramme per cubic centimetre. Kg per cubic metre is another way to measure density (in metre-kilogram-second or SI units). Air, for instance, has a density of 1.2 kilogrammes per cubic metre. Books and manuals list the densities of typical solids, liquids, and gases. An easy way to determine a body's mass from its volume, or vice versa, is by its density.
Learn more about density here:
https://brainly.com/question/15164682
#SPJ4