The pressure difference between points A and B of the pipe is 25113.6 N/m². A pipe contains an oil of specific gravity (sp. gr.) 0.8.
A differential manometer is attached at two points A and B of the pipe. The mercury level difference is 20 cm. The difference of pressure at the two points is to be calculated.Let p_A and p_B be the pressures at points A and B of the pipe, respectively. And, let ρ be the density of the mercury used in the differential manometer. Then the pressure difference is given by:
p_A - p_B = ρ g h…(i)
where h is the difference in mercury level shown by the differential manometer and g is the acceleration due to gravity. Therefore, we have to find the pressure difference between points A and B.The specific gravity of the oil is given by:
sp. gr. = ρ/ρ_w…(ii)
where ρ_w is the density of water. Therefore, the density of the oil can be given as:ρ = sp. gr. × ρ_wSubstituting this value of density in equation (i),
we have:p_A - p_B
= ρ g h
= sp. gr. × ρ_w × g h
We know that the density of mercury is greater than that of water. Hence, the specific gravity of mercury is greater than 1. Therefore, we can assume the specific gravity of mercury to be 13.6. Hence, we can rewrite the expression for the pressure difference as:
p_A - p_B = 13.6 × 1000 × 9.81 × 0.2 × 0.8
= 25113.6 N/m²
Therefore, the pressure difference between points A and B of the pipe is 25113.6 N/m².
For more information on manometer visit:
brainly.com/question/17166380
#SPJ11
We wish to calculate the Joule-Thomson coefficient for methane at 284 K and a specific volume of 19 L/mol. We can assume a constant-pressure heat capacity of 1114 J/kg/K, and a volume expansivity of 0.007 K-1. Report your answer with units of K/bar.
The Joule-Thomson coefficient for methane at 284 K and a specific volume of 19 L/mol is approximately -0.002 K/bar.
The Joule-Thomson coefficient is a measure of how the temperature of a gas changes as it expands or compresses under constant enthalpy conditions. It is calculated using the equation:
μ = (1/Cp) * (dT/dV) + V * α
Where:
- μ is the Joule-Thomson coefficient
- Cp is the constant-pressure heat capacity
- dT/dV is the rate of change of temperature with respect to volume
- V is the specific volume
- α is the volume expansivity
To calculate the Joule-Thomson coefficient, we can substitute the given values into the equation. Given that Cp is 1114 J/kg/K, dT/dV is zero since the specific volume is constant, V is 19 L/mol, and α is 0.007 K-1, we can simplify the equation to:
μ = V * α = 19 L/mol * 0.007 K-1 = 0.133 K/mol
To convert the units to K/bar, we need to divide by the conversion factor of 0.1 bar/L, resulting in:
μ = 0.133 K/mol / 0.1 bar/L = -0.002 K/bar
Therefore, the Joule-Thomson coefficient for methane at 284 K and a specific volume of 19 L/mol is approximately -0.002 K/bar.
Know more about Joule-Thomson coefficient here:
https://brainly.com/question/31537968
#SPJ11
Make the following phase diagram WITH THE GIVEN DATA THAT IS SILVER AND COPPER IN THE FOLLOWING PHASE DIAGRAM, NO THE DRIAGRAM OF MAGNETIUM AND ALUMINUM THAT IS WRONG
copper silver phase diagram, copper silver phase diagram
Show how you got to the result (lever rule, etc) and draw on the diagram
in a Cu-7% Ag alloy that solidifies Slowly determine: The liquidus temperature, that of the solidus, that of solvus and the solidification interval The composition of the first solid form a) The amounts and compositions of each phase at 1000 ºC
b) The amounts and compositions of each phase at 850 ºC
c) The amounts and compositions of each phase at 781 ºC
d) The amounts and compositions of each phase at 779 ºC
e) The amounts and composition of each phase at 600 ºC Repeat from a to g for: Cu-30% alloy Ag and Cu-80% Ag
The Cu-Ag segment diagram affords valuable facts regarding the temperature degrees, compositions, and stages present in exclusive Cu-Ag alloys. Utilizing the lever rule and relating it to the section diagram lets in for the dedication of section compositions and amounts at unique temperatures.
I can provide you with the essential information based on the given facts for the Cu-Ag segment diagram.
To determine the specified records, we need to consult the Cu-Ag section diagram. Here are the records you requested:
Given:
Cu-7% Ag alloy that solidifies slowly
a) At 1000 ºC:
Liquidus temperature: Referring to the section diagram, discover the temperature at which the liquid segment region ends.
Solidus temperature: Referring to the segment diagram, locate the temperature in which the strong segment place starts offevolved.
Solvus temperature: Referring to the segment diagram, find the temperature where the stable solution area ends.
Solidification interval: The temperature variety between the liquidus and solidus temperatures.
B) At 850 ºC, 781 ºC, 779 ºC, and 600 ºC:
Determine the phase(s) gift at each temperature: Refer to the section diagram and perceive the segment(s) that exist at the given temperatures.
Determine the quantity and composition of each phase: Use the lever rule to decide the proportions and compositions of each segment based on the given alloy composition (Cu-7% Ag in this example).
Repeat the above steps for the Cu-30% Ag and Cu-80% Ag alloys.
To know more about Cu-Ag
https://brainly.com/question/15576869
#SPJ4
An online music store sells songs on its website. Each song is the same price. The cost to purchase 8 songs is $10.
Create an equation to represent the relationship between the total cost, c, and the number of songs, s, purchased.
Enter your equation in the box below.
Answer:
The equation to represent the relationship between the total cost , c, and the number of songs, s, purchased can be expressed as:
c = 10/8 * s
This equation assumes that each song is the same price and that the cost to purchase 8 songs is $10
Step-by-step explanation:
Drag the tiles to the boxes to form correct pairs.
Match each operation involving f(x) and g(x) to its answer.
f(X) = 1-×2 and g(x)= √ 11-4x
(g x f(2)
(f/g)(-1)
(g+f)(2)
(9-f)(-1)
-373
√ 3-3
√ 15
0
Matching the operations with their answers:
(g ∘ f)(2) → √23
(f/g)(-1) → 0
(g + f)(2) → √3 - 3
(9 - f)(-1) → 9
Matching:
(g ∘ f)(2) → √23
(f/g)(-1) → 0
(g + f)(2) → √3 - 3
(9 - f)(-1) → 9
To match each operation involving f(x) and g(x) to its answer, let's evaluate each expression:
1. (g ∘ f)(2):
(g ∘ f)(2) means we substitute f(2) into g(x).
[tex]f(x) = 1 - x^2[/tex]
f(2) = 1 - 2^2 = 1 - 4 = -3
Now, we substitute -3 into g(x):
g(x) = √(11 - 4x)
(g ∘ f)(2) = g(-3) = √(11 - 4(-3)) = √(11 + 12) = √23
2. (f/g)(-1):
(f/g)(-1) means we substitute -1 into both f(x) and g(x).
[tex]f(x) = 1 - x^2\\f(-1) = 1 - (-1)^2 = 1 - 1 = 0[/tex]
g(x) = √(11 - 4x)
g(-1) = √(11 - 4(-1)) = √(11 + 4) = √15
3. (g + f)(2):
(g + f)(2) means we add f(2) and g(2).
[tex]f(x) = 1 - x^2\\f(2) = 1 - 2^2 = 1 - 4 = -3[/tex]
g(x) = √(11 - 4x)
g(2) = √(11 - 4(2)) = √(11 - 8) = √3
(g + f)(2) = g(2) + f(2) = √3 + (-3) = √3 - 3
4. (9 - f)(-1):
(9 - f)(-1) means we substitute -1 into f(x) and subtract the result from 9.
[tex]f(x) = 1 - x^2\\f(-1) = 1 - (-1)^2 = 1 - 1 = 0\\(9 - f)(-1) = 9 - f(-1) = 9 - 0 = 9[/tex]
Matching the operations with their answers:
(g ∘ f)(2) → √23
(f/g)(-1) → 0
(g + f)(2) → √3 - 3
(9 - f)(-1) → 9
Matching:
(g ∘ f)(2) → √23
(f/g)(-1) → 0
(g + f)(2) → √3 - 3
(9 - f)(-1) → 9
for such more question on expression
https://brainly.com/question/4344214
#SPJ8
Coal with the following composition: total carbon 72 %; volatile matter 18 %, fixed carbon 60 %; free water 5 %, was combusted in a small furnace with dry air. The flowrate of the air is 50 kg/h. 5% carbon leaves the furnace as uncombusted carbon. The coal contains no nitrogen, nor sulphur. The exhaust gas Orsat analysis has the following reading CO2 12.8 %; CO = 1.2%; 02 = 5.4 %6. In addition to the flue gas, a solid residue comprising of unreacted carbon and ash leaves the furnace. a. Submit a labeled block flow diagram of the process. b. What is the percentage of nitrogen (N2) in the Orsat analysis? c. What is the percentage of ash in the coal? d. What is the flowrate (in kg/h) of carbon in the solid residue? e. What is the percentage of the carbon in the residue? f. How much of the carbon in the coal reacts (in kg/h)? g. What is the molar flowrate (in kmol/h) of the dry exhaust gas? How much air (kmol/h) is fed?
a) The Block flow diagram is given below. b) Percentage of nitrogen is 70.6%. c) Percentage of ash is 9%. d) Flowrate is 2.5 kg/h. e) Percentage of the carbon is 83.33%. f) The amount of carbon is 47.5 kg/h. g) Molar flowrate is 0.49 kmol/h, amount is 21.74 kmol/h.
a. Block flow diagram
Coal
+
Air
=
Flue gas
+
Residue
b. Percentage of nitrogen (N2) in the Orsat analysis
The percentage of nitrogen in the Orsat analysis is 100 - (12.8 + 1.2 + 5.4) = 70.6%.
c. Percentage of ash in the coal
The percentage of ash in the coal is 100 - (72 + 18 + 60 - 5) = 9%.
d. Flowrate (in kg/h) of carbon in the solid residue
The flowrate of carbon in the solid residue is 0.05 * 50 kg/h = 2.5 kg/h.
e. Percentage of the carbon in the residue
The percentage of carbon in the residue is 2.5 kg/h / (2.5 + 0.5) kg/h * 100% = 83.33%.
f. How much of the carbon in the coal reacts (in kg/h)
The amount of carbon in the coal that reacts is 50 kg/h - 2.5 kg/h = 47.5 kg/h.
g. Molar flowrate (in kmol/h) of the dry exhaust gas
The molar flowrate of the dry exhaust gas is 0.128 * 50 kg/h / 12.01 kg/kmol = 0.49 kmol/h.
The amount of air fed is 50 kg/h / 0.23 kg/kmol = 21.74 kmol/h.
To learn more about Percentage here:
https://brainly.com/question/14801224
#SPJ4
A gas turbine is used to generate electricity. It can be modelled as a cycle utilising air as the working fluid. The air is initially compressed in a two stage compressor from 1 bar to 16 bar. The air is initially at 32"C. Between the two stages of the compressor, there is an intercooler which reduces the temperature to 32°C. It may be assumed that the two stages of the compressor have an equal pressure ratio. The compressed gas then passes to a heat exchanger, which models the combustion chamber, where it is heated to 1500'C. The hot gases are then expanded through a turbine to extract work, and the exhaust gases vented at 1 bar. It may be assumed throughout that all rotating machinery has an isentropic efficiency of 90% What are the advantages and disadvantages of using a multi-stage compressor over a single stage? [2] ) How are the isentropic efficiencies of a compressor and a turbine defined? [2] (i) For an isentropic process on a perfect gas, it can be shown that pr constant. Starting from this expression, show that: T: T: [4] () For this cycle, calculate the back work ratio and the thermal efficiency. How does this compare with the maximum efficiency possible for this cycle? How could you improve the thermal efficiency of this process? [12] Data: For air: Cp 1.15 kJ/kg Ky 1.33 P.
The advantages of using a multi-stage compressor over a single stage include higher overall pressure ratios, improved efficiency, and better performance. The division of compression into multiple stages allows for lower pressure ratios per stage, reducing the workload and enabling better control. Intercooling between stages further enhances efficiency. However, multi-stage compressors are more complex, expensive, and have a higher risk of operational issues.The main disadvantages of using a multi-stage compressor are increased complexity, higher costs, and a greater potential for operational issues compared to single-stage compressors.
Advantages and disadvantages of using a multi-stage compressor over a single stage:
The main advantage of a multi-stage compressor is its ability to achieve higher overall pressure ratios, leading to improved efficiency and performance. By dividing the compression process into multiple stages, each stage operates at a lower pressure ratio, reducing the workload on each stage and allowing for better control and optimization. Additionally, intercooling between stages can help lower the temperature and improve efficiency further. However, multi-stage compressors are more complex and expensive than single-stage compressors, requiring additional equipment, maintenance, and space. They also introduce more potential points of failure, increasing the risk of operational issues.
Isentropic efficiencies of a compressor and a turbine are defined as follows:
The isentropic efficiency of a compressor is the ratio of the actual work input to the ideal work input, assuming an isentropic (reversible adiabatic) process. It represents the efficiency with which the compressor raises the pressure of the working fluid.
The isentropic efficiency of a turbine is the ratio of the actual work output to the ideal work output, assuming an isentropic process. It represents the efficiency with which the turbine extracts work from the working fluid.
Starting from the expression pr constant (pressure ratio constant), we can derive the relationship between temperatures at different points in an isentropic process. By applying the ideal gas law and rearranging the equation, we obtain the relationship T1/T2 = (P1/P2)^((k-1)/k), where T1 and T2 are the temperatures at points 1 and 2, and P1 and P2 are the pressures at points 1 and 2, respectively. This equation shows that the temperature ratio is related to the pressure ratio by the specific heat ratio (k) of the gas.
To calculate the back work ratio and thermal efficiency for the given cycle, we need to determine the specific heat capacity (Cp), specific gas constant (R), and specific heat ratio (k) of the air. With these values, we can calculate the back work ratio (BWR) as the ratio of the work required for compression to the work produced by the turbine. The thermal efficiency (ηth) is the ratio of the net work output to the heat input.
To improve the thermal efficiency of this process, several approaches can be considered. One option is to increase the intercooling efficiency to reduce the temperature at the compressor inlet. Another possibility is to enhance the combustion process to achieve higher temperatures and better combustion efficiency. Additionally, improving the turbine's isentropic efficiency would increase the work output. Utilizing waste heat recovery techniques, such as a bottoming cycle or combined heat and power (CHP) systems, can also boost the overall thermal efficiency by utilizing the heat from the exhaust gases for additional purposes.
Know more about isentropic process here:
https://brainly.com/question/13001880
#SPJ11
A rotary pump draws oil from (tank 1) and delivers it into (tank2), the level in (tank 1) is 3 m below the base of (tank 2) and the level in (tank 2) is 6 m. If the pump sits 2 m above the base of (tank 2) and discharges into the side of the tank 2 at a height of 4 m, what is the static discharge head?
Given the distance between the oil source tank (Tank 1) and oil discharge tank (Tank 2) is 3m and the height difference between the two tanks is 6m. It is also known that the pump is placed 2m above the base of Tank 2. This makes the discharge height of the pump 4m. The static discharge head of the rotary pump needs to be calculated
The static discharge head of a rotary pump is calculated using the formula, Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2.The following are the given values in the problem: Height of tank 2 = 6 m. Elevation difference between the tanks = 3 m. Height of the pump above the base of tank 2 = 2 m. Discharge height of the pump = 4 m. Using the formula for static discharge head, we can calculate it as follows: Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2. Static discharge head = 6 + 3 + 4 - 2. Static discharge head = 11Therefore, the static discharge head of the rotary pump is 11 m. Height of tank 2 = 6 m. Elevation difference between the tanks = 3 m. Height of the pump above the base of tank 2 = 2 m. Discharge height of the pump = 4 m. To calculate the static discharge head, we can use the formula, Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2.The height of tank 2 is 6 m, the elevation difference between the tanks is 3 m, the discharge height of the pump is 4 m, and the height of the pump above the base of tank 2 is 2 m. Using these values, we can calculate the static discharge head as follows: Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2Static discharge head = 6 + 3 + 4 - 2Static discharge head = 11Thus, the static discharge head of the rotary pump is 11 m.
In conclusion, the static discharge head of the rotary pump that draws oil from tank 1 and delivers it into tank 2 is 11 m.
learn more about Static discharge visit:
brainly.com/question/8338731
#SPJ11
When glucose acts on pancreatic-beta cells, what is (activated)
responsible for the depolarization of the membrane that ultimately
leads to insulin secretion?
The activation of ATP-sensitive potassium channels (KATP channels) and subsequent increase in intracellular calcium levels (Ca2+) lead to insulin secretion in pancreatic-beta cells when glucose acts on them.
Glucose acts as a stimulator for insulin secretion in pancreatic-beta cells. When glucose enters the cells, it undergoes glycolysis and generates ATP. The rise in ATP levels inhibits the activity of KATP channels, leading to their closure. This closure prevents the efflux of potassium ions, causing depolarization of the cell membrane.
Depolarization of the cell membrane leads to the opening of voltage-gated calcium channels, allowing an influx of calcium ions into the cell. The increased levels of intracellular calcium trigger the release of insulin-containing vesicles (granules) from the pancreatic-beta cells. These vesicles fuse with the cell membrane and release insulin into the bloodstream.
Therefore, the activation of KATP channels and the subsequent increase in intracellular calcium levels are the key events that lead to insulin secretion when glucose acts on pancreatic-beta cells.
Know more about ATP here:
https://brainly.com/question/174043
#SPJ11
Lists the ordinates of - run off hydrograph shown in the table. below which were in response to a rainfall 20.9mm during the first two hours, 41.9mm in the next two hours, and 30.9mm during the last two hours of the rainfall which lasted for six hours. Catchment area is 133.1 km^2. Assume a constant 5 m^3/sec constant base flow, find - Index. Time(hr.) 0 2 4 6 8 10 12 14 16 18 Q(m³/sec) 0 171 313 522 297 133 51 5 5 5 ≈1.42 mm/hr O ≈1.76 mm/hr ≈ 2.04 mm/hr O ≈2.13 mm/hr 10 points
To calculate the ordinates of the runoff hydrograph, we need to subtract the base flow from the total flow values given in the table.
Catchment area = 133.1 km²
Base flow = 5 m³/sec
To find the runoff values, we subtract the base flow from the corresponding flow values:
Time(hr.) Q(m³/sec) Runoff (Q - Base flow)
0 0 0
2 171 166
4 313 308
6 522 517
8 297 292
10 133 128
12 51 46
14 5 0
16 5 0
18 5 0
The runoff hydrograph ordinates, obtained by subtracting the base flow from the total flow values, are as follows:
0, 166, 308, 517, 292, 128, 46, 0, 0, 0
Now, let's calculate the intensity index:
Intensity Index = Total Rainfall (mm) / Duration of Rainfall (hr)
Total Rainfall = 20.9 + 41.9 + 30.9 = 93.7 mm
Duration of Rainfall = 6 hours
Intensity Index = 93.7 mm / 6 hours
Intensity Index ≈ 15.62 mm/hr
Therefore, the intensity index for the given rainfall is approximately 15.62 mm/hr.
Learn more about run-off:
https://brainly.com/question/3228016
#SPJ11
The product of the slopes of lines
and
is
.
Answer:
wrong question correct it..
Answer:
Step-by-step explanation:
you a good
for the t
Prove the statement n power n /3 power n < n! for n ≥ 6 by
induction
We will prove the statement [tex]n^n / 3^n < n![/tex]for n ≥ 6 by induction. The base case is n = 6, and we will assume the inequality holds for some k ≥ 6. Using the induction hypothesis, we will show that it also holds for k + 1. Thus, proving the statement for n ≥ 6.
Base case: For n = 6, we have 6⁶ / 3⁶ = 46656 / 729 ≈ 64. As 6! = 720, we can see that the statement holds for n = 6.
Inductive step: Assume that the inequality holds for some k ≥ 6, i.e.,
[tex]k^k / 3^k < k!.[/tex] We need to show that it holds for k + 1 as well.
Starting with the left side of the inequality:
[tex](k + 1)^{k + 1} / 3^{k + 1} = (k + 1) * (k + 1)^k / 3 * 3^k[/tex]
[tex]= (k + 1) * (k^k / 3^k) * (k + 1) / 3[/tex]
Since k ≥ 6, we know that (k + 1) / 3 < 1. Therefore, we can write:
[tex](k + 1) * (k^k / 3^k) * (k + 1) / 3 < (k + 1) * (k^k / 3^k) * 1[/tex]
[tex]= (k + 1) * (k^k / 3^k)[/tex]
< (k + 1) * k!
= (k + 1)!
Thus, we have shown that if the inequality holds for k, then it also holds for k + 1. By the principle of mathematical induction, the statement
[tex]n^n / 3^n < n![/tex] is proven for all n ≥ 6.
To learn more about induction hypothesis visit:
brainly.com/question/32656703
#SPJ11
Which polynomial function has a leading coefficient of 3 and roots –4, i, and 2, all with multiplicity 1?
f(x) = 3(x + 4)(x – i)(x – 2)
f(x) = (x – 3)(x + 4)(x – i)(x – 2)
f(x) = (x – 3)(x + 4)(x – i)(x + i)(x – 2)
f(x) = 3(x + 4)(x – i)(x + i)(x – 2)
How would you define aggregates as applied to civil engineering? What are the general uses of aggregates in civil engineering?
In civil engineering, aggregates refer to granular materials such as sand, gravel, crushed stone, or recycled materials used in construction. They are commonly mixed with cement and water to form concrete, serving as the main bulk and filler material.
The general uses of aggregates in civil engineering include:
1. Concrete Production: Aggregates form the major component of concrete, providing strength, durability, and volume. They help in achieving the desired workability, strength, and appearance of concrete structures.
2. Road Construction: Aggregates are used as a base or subbase material in the construction of roads, highways, and pavements. They provide stability, load-bearing capacity, and resistance to wear and tear.
3. Drainage and Filtration: Aggregates are used in drainage systems, filter beds, and geotechnical applications to facilitate water flow, prevent soil erosion, and enhance filtration and purification processes.
4. Landscaping and Beautification: Aggregates are employed in landscaping projects, such as garden pathways, decorative elements, and surface coatings, to enhance aesthetics and provide functionality.
5. Building Foundations: Aggregates are used as a base material for building foundations, providing stability and load distribution to support the weight of structures.
Therefore, aggregates play a crucial role in civil engineering by providing essential properties to construction materials like concrete, contributing to the strength, durability, and functionality of various infrastructure projects. They are versatile and widely used in diverse applications across the field of civil engineering.
Learn more about civil engineering visit:
https://brainly.com/question/32893375
#SPJ11
Environmental Impact of Fossil Fuels and Crude Oil Refining 1. The primary reaction of the components of natural gas is combustion with oxygen form the air. The primary product of these combustion reactions is energy. List three chemical by-products of this energy- producing reaction.
The three chemical by-products of the energy-producing reaction between natural gas and oxygen are carbon dioxide (CO2), water vapor (H2O), and nitrogen oxide (NOx).
When natural gas, which primarily consists of methane (CH4), undergoes combustion with oxygen from the air, it releases energy. This exothermic reaction produces several chemical by-products. The first by-product is carbon dioxide (CO2), a greenhouse gas that contributes to global warming and climate change when released into the atmosphere. CO2 is a significant concern as it accumulates over time and traps heat, leading to an increase in the Earth's average temperature.
The second by-product is water vapor (H2O), which is formed when hydrogen from the natural gas combines with oxygen. Water vapor is a natural component of the atmosphere, but its presence in large quantities can contribute to the greenhouse effect. It can also lead to the formation of clouds and precipitation, affecting local weather patterns.
Lastly, the combustion reaction of natural gas also produces nitrogen oxide (NOx), a collective term for nitrogen monoxide (NO) and nitrogen dioxide (NO2). These compounds are known as air pollutants and contribute to the formation of smog and acid rain. NOx emissions have harmful effects on human health, damaging the respiratory system and contributing to the formation of respiratory diseases.
Learn more about Natural gas combustion
brainly.com/question/10203028
#SPJ11
A Class A pan was located in the vicinity of swimming pool (surface area=500 m^2) the amounts of water added to bring the level to the fixed point are shown in the table. Calculate the total evaporation (m^3) losses from the pool during a week, assuming pan coefficient 0.75 3 4 5 6 Day Rainfall (mm) 1 1 0 0 4.5 0.5 Water added 4.8 6.9 6.7 6.2 -1 3 (mm) O 14.250 m^3 O 14.652 m^3 O 14.475 m^3 O 14.850 m^3 20 10 points 706 6
To calculate the total evaporation losses from the pool during a week, we need to consider the rainfall and the water added to the pool. We can use the pan coefficient of 0.75 to estimate the evaporation losses based on the water added.
Surface area of the pool = 500 m^2
Pan coefficient = 0.75
Using the table provided, let's calculate the evaporation losses for each day:
Day 1:
Rainfall = 1 mm
Water added = 4.8 mm
Evaporation = Water added - (Rainfall * Pan coefficient)
Evaporation = 4.8 - (1 * 0.75)
Evaporation = 4.8 - 0.75
Evaporation = 4.05 mm
Day 2:
Rainfall = 1 mm
Water added = 6.9 mm
Evaporation = Water added - (Rainfall * Pan coefficient)
Evaporation = 6.9 - (1 * 0.75)
Evaporation = 6.9 - 0.75
Evaporation = 6.15 mm
Day 3:
Rainfall = 0 mm
Water added = 6.7 mm
Evaporation = Water added - (Rainfall * Pan coefficient)
Evaporation = 6.7 - (0 * 0.75)
Evaporation = 6.7 mm
Day 4:
Rainfall = 0 mm
Water added = 6.2 mm
Evaporation = Water added - (Rainfall * Pan coefficient)
Evaporation = 6.2 - (0 * 0.75)
Evaporation = 6.2 mm
Day 5:
Rainfall = 4.5 mm
Water added = -1 mm
Since water was not added but instead decreased by 1 mm, we can assume no evaporation losses for this day.
Day 6:
Rainfall = 0.5 mm
Water added = 3 mm
Evaporation = Water added - (Rainfall * Pan coefficient)
Evaporation = 3 - (0.5 * 0.75)
Evaporation = 3 - 0.375
Evaporation = 2.625 mm
Now, let's calculate the total evaporation losses for the week:
Total evaporation = Evaporation on Day 1 + Evaporation on Day 2 + Evaporation on Day 3 + Evaporation on Day 4 + Evaporation on Day 5 + Evaporation on Day 6
Total evaporation = 4.05 + 6.15 + 6.7 + 6.2 + 0 + 2.625
Total evaporation = 25.825 mm
To convert the evaporation from millimeters (mm) to cubic meters (m^3), we need to divide by 1000:
Total evaporation = 25.825 / 1000
Total evaporation ≈ 0.025825 m^3
Therefore, the total evaporation losses from the pool during the week are approximately 0.025825 m^3.
Learn more about evaporation:
https://brainly.com/question/24258
#SPJ11
Please help ASAP and show work how you got it please
Answer: 6.928
Step-by-step explanation:
cos∅=adjacent/hypotenuse
cos(30)=x/8
8[cos(30)]= [x/8]8
8×cos(30)=x
plug into a calculator
6.928=x
Which of the following sentences is a contradiction? Select one: O O a. (q→ p) → (p → q) b. (q V p) → (p→q) c. None of the given choices. d. (p →q) → (q→ p)
By following these steps, you can kill a locked-up program and display the permissions of a file or directory in a Linux environment.
To kill a program that has locked up in a Linux environment, you can use the `kill` command. Here's how you can do it:
1. Identify the process ID (PID) of the program: You need to find the PID of the program that has locked up. You can use the `ps` command along with other utilities like `grep` to search for the specific program. For example, if you are looking for a program named "myprogram", you can run the following command:
```
ps aux | grep myprogram
```
This will display a list of processes matching the name "myprogram" along with their corresponding PIDs.
2. Kill the program using the PID: Once you have identified the PID of the program, you can use the `kill` command to send a signal to terminate the process. The most commonly used signal is SIGTERM (termination signal). To kill the program, execute the following command, replacing "PID" with the actual process ID:
```
kill PID
```
If the program does not respond to the termination signal, you can try using the SIGKILL signal, which forcefully terminates the process. To send the SIGKILL signal, use the `-9` option with the `kill` command:
```
kill -9 PID
```
Note that using the SIGKILL signal should be the last resort as it does not allow the program to perform any cleanup operations.
Regarding displaying the permissions (perms) of a file or directory in Linux, you can use the `ls` command with the `-l` option. Here's how you can do it:
1. Open a terminal: Launch a terminal in your Linux environment.
2. Navigate to the directory or provide the file path: Use the `cd` command to navigate to the directory containing the file whose permissions you want to display. If the file is located in a different directory, you can provide the file path directly.
3. Run the `ls` command with the `-l` option: Execute the following command:
```
ls -l
```
This command will list the files and directories in the current directory, along with their detailed information, including permissions, ownership, size, and modification time.
The permissions of a file are displayed in the first column of the output. The permissions are represented by a combination of letters and symbols. The first character indicates the file type (e.g., `-` for a regular file, `d` for a directory), and the next nine characters represent the permissions for the owner, group, and others. Each set of three characters represents read (`r`), write (`w`), and execute (`x`) permissions, respectively. For example, `-rw-r--r--` indicates that the owner has read and write permissions, while the group and others have only read permissions.
To know more about Linux click-
https://brainly.com/question/33210963
#SPJ11
QUESTION 8 5 points Save Answer Describe the principle behind the operation of air classification process used in processing solid waste. Also, explain what materials can be separated from commingled
Air classification is a process used in processing solid waste to separate materials based on their size, shape, and density. It involves the use of an air stream to separate lighter materials from heavier ones, utilizing the principle of differential settling.
In the air classification process, solid waste materials are fed into a chamber where they come into contact with a high-velocity air stream. The air stream carries the solid waste particles upward, creating a suspension of particles in the chamber. As the particles are suspended in the air stream, they experience different forces based on their size, shape, and density.
Heavier materials, such as metals and glass, have a greater inertia and momentum, allowing them to settle faster and be separated from the lighter materials. These heavier materials are collected at the bottom of the chamber through a gravity separation mechanism, such as a conveyor belt or a hopper.
On the other hand, lighter materials, such as paper, plastic, and organic waste, have less inertia and are carried by the air stream further upward. They are directed towards a different collection point, often through a cyclone or a series of filters, where they can be further processed or recycled.
The air classification process is particularly effective in separating commingled materials, which are mixed together in the waste stream. By taking advantage of the differences in size, shape, and density of the materials, the process can efficiently separate valuable recyclable materials from non-recyclable waste.
Learn more about the air classification process
#SPJ11
What is the simplest form of
18ab3
18b4
162ab3
162ab4
Answer:
Step-by-step explanation:
it is A - 18ab3
Answer:
question 1. A question 2. C
To what temperature must 15 L of oxygen gas at -43°C be heated at 1 atm pressure in order to occupy a volume of 23 L, assuming that the pressure increases by 47 mm Hg?
The temperature heated to 331.06 K in order for the oxygen gas to occupy a volume of 23 L at a pressure increase of 47 mm Hg.
To solve this problem, use the ideal gas law:
PV = nRT
where:
P is the pressure (in atm),
V is the volume (in liters),
n is the number of moles of gas,
R is the ideal gas constant (0.0821 L·atm/(mol·K)),
T is the temperature (in Kelvin).
First, to convert the given temperature from Celsius to Kelvin:
T1 = -43°C + 273.15 = 230.15 K
Given:
Initial volume (V1) = 15 L
Final volume (V2) = 23 L
Pressure change (ΔP) = 47 mm Hg
Pressure (P1) = 1 atm
Converting the pressure change from mm Hg to atm:
ΔP = 47 mm Hg × (1 atm / 760 mm Hg) = 0.0618 atm
Using the ideal gas law for the initial state:
P1V1 = nRT1
And for the final state:
(P1 + ΔP)V2 = nRT2
Dividing the second equation by the first equation, we can eliminate n and R:
[(P1 + ΔP)V2] / (P1V1) = T2 / T1
Substituting the given values:
[(1 + 0.0618) × 23] / 15 = T2 / 230.15
Simplifying:
1.0618 × 23 / 15 = T2 / 230.15
0.0618 × 23 × 230.15 = T2
Substituting the values and calculating:
T2 ≈ 331.06 K
To know more about volume here
https://brainly.com/question/28058531
#SPJ4
Consider the following Scenario and answer the question: Scenario: Salman is in 1st period and he skipped breakfast today. He decides to have a bagel in his backpack and he will eat it during class when the teacher is not looking. Later on and in order to make sure the correct chemical is being used, he smells the chemical. Instead of using his hand to waft the vapors toward his nose, he sticks his face as close as he can to the chemical and takes a big whiff of the tray. He feels dizzy and his nose burns for the rest of the day. Identify the safety rules that are being violated? What are the possible risks in this scenario and how can you minimize the harm?
In this given scenario, the following safety rules are being violated by Salman: Salman is eating food during the laboratory which can lead to contamination, as the laboratory equipment is not safe for food or drinks.
Inhaling chemicals directly from the tray or bottle without proper ventilation can cause serious health hazards.
The experiment might not give the expected results if the procedure is not followed properly.
Furthermore, not following instructions can lead to personal harm.
What are the possible risks in this scenario and how can you minimize the harm?
There are a few risks in the given scenario, as follows:
Salman could have suffered serious injuries from inhaling the vapors of the chemical directly from the bottle, as he should have been using his hand to waft the vapors toward his nose to check the smell.
Salman could have contaminated the experiment he was conducting by eating in the laboratory.
He could have also spread germs or bacteria from the bagel into the lab equipment or chemicals which could have led to inaccurate results.
Know more about contamination here:
https://brainly.com/question/465199
#SPJ11
Determine the electron pair geometry /molecular geometry for the following compound: SO, a)Tetrahedral/Tetrahedral b)Tetrahedral/ Trigonal planar c)Trigonal planar/Trigonal planar d)Tetrahedral/Trigonal pyramidal e)Trigonal planar/Trigonal pyramidal
c) Trigonal planar/Trigonal planar
The compound SO (sulfur monoxide) consists of one sulfur atom (S) and one oxygen atom (O). To determine the electron pair geometry and molecular geometry of this compound, we need to consider the number of electron groups around the central atom (S).
In the case of SO, sulfur has six valence electrons, and oxygen has six valence electrons. The total number of valence electrons in the compound is therefore 12. Since there are no lone pairs of electrons on the central sulfur atom, all the electron groups are bonded pairs.
In the electron pair geometry, we consider both the bonded and lone pairs of electrons. Since there are three bonded pairs of electrons around the central sulfur atom, the electron pair geometry is trigonal planar.
In the molecular geometry, we only consider the positions of the bonded atoms, ignoring the lone pairs. In the case of SO, the oxygen atom is bonded to the sulfur atom, resulting in a trigonal planar molecular geometry.
Therefore, the correct answer is c) Trigonal planar/Trigonal planar.
Learn more about Trigonal planar
brainly.com/question/32826707
#SPJ11
Determine the volume excluded per molecule of neon, if 1.6 moles of the pure gas occupy a volume of 1 L, at a temperature of 323 K and a pressure of 43.08 atm. Using this molecular volume, estimate the radius of a neon atom. Information R = 0.0821 L atm K-4 mol-1 a = 0.212 L2 atm mol-2 Avogadro's number = 6.023 x 1023 molec/mol =
The estimated radius of a neon atom is approximately 2.36 x [tex]10^{-10}[/tex] meters.
To determine the volume excluded per molecule of neon, we can use the van der Waals equation of state:
[tex](P + a(n^{2}/V^{2}))(V - nb) = nRT[/tex]
Where:
P = Pressure
V = Volume
n = Number of moles
R = Gas constant
a = van der Waals constant
b = co-volume
We need to rearrange the equation to solve for the excluded volume (Vex):
Vex = V - nb
Given:
P = 43.08 atm
V = 1 L
n = 1.6 moles
[tex]R = 0.0821 L atm K^{-1} mol^{-1}[/tex]
[tex]a = 0.212 L^{2} atm mol^{-2}[/tex]
First, let's calculate the value of b:
[tex]b = (0.0821 L atm K^{-1} mol^{-1}) * (323 K) / (43.08 atm)[/tex]
[tex]b = 0.615 L mol^{-1}[/tex]
Now, we can calculate the excluded volume:
Vex = V - nb
[tex]Vex = 1 L - (1.6 mol * 0.615 L mol^{-1})[/tex]
Vex = 0.016 L
The excluded volume per molecule (Vex/molecule) can be determined by dividing Vex by the number of moles of neon (n):
Vex/molecule = Vex / (n * Avogadro's number)
Given:
Avogadro's number = [tex]6.023 x 10^{23} molec/mol[/tex]
Vex/molecule =[tex](0.016 L) / (1.6 mol * 6.023 x 10^{23} molec/mol)[/tex]
Vex/molecule = [tex]1.655 x 10^{-26)} L/molec[/tex]
Now, let's estimate the radius of a neon atom using the excluded volume. Assuming a spherical neon atom, the volume excluded by one neon atom (Vatom) is related to its radius (r) as:
Vatom = (4/3) * π *[tex]r^3}[/tex]
Since Vatom is equal to Vex/molecule, we can equate the equations:
(4/3) * π * [tex]r^3}[/tex] = Vex/molecule
Now, rearrange the equation to solve for the radius (r):
[tex]r^3 }[/tex]= (3 * Vex/molecule) / (4 * π)
r = (3 * Vex/molecule / (4 * π[tex]))^{1/3}[/tex]
Substituting the calculated value for Vex/molecule:
r = (3 * 1.655 x [tex]10^{-26}[/tex] L/molec / (4 * π)[tex])^{1/3}[/tex]
r ≈ 2.36 x 10^(-10) meters
Therefore, the estimated radius of a neon atom is approximately 2.36 x [tex]10^{-10}[/tex] meters.
For more details of estimated radius:
https://brainly.com/question/22742317
#SPJ4
Draw the following molecule: N,N-dibutyl -3-amino- Hexane
To draw the molecule N, N-dibutyl-3-amino-hexane, follow these steps:
1. Start by drawing a straight chain of six carbon atoms, representing the hexane backbone.
H H H H H H
| | | | | |
C-C-C-C-C-C
2. Next, identify the amino group (-NH2) on the third carbon atom. Replace one of the hydrogen atoms on the third carbon atom with the amino group.
H H NH2 H H H
| | | | | |
C-C-C-N-C-C-C
3. Now, focus on the N, N-dibutyl substituent. This means there are two butyl groups attached to the nitrogen atom (N). Draw two separate butyl groups (four-carbon chains) coming off the nitrogen atom.
H H H H H H
| | | | | |
C-C-C-N-C-C-C
|
C
|
C
|
C
|
C
4. Finally, complete the structure by adding hydrogen atoms to all remaining carbon atoms to satisfy their bonding requirements.
H H H H H H
| | | | | |
C-C-C-N-C-C-C
|
C
|
C
|
C
|
C
H H H H H H
| | | | | |
C-C-C-N-C-C-C
|
C
|
C
|
C
|
C
H H H H H H
| | | | | |
C-C-C-N-C-C-C
|
C
|
C
|
C
|
C
Remember, the structure shown here is just one of the possible ways to draw N, N-dibutyl-3-amino-hexane. The main focus is to correctly represent the hexane backbone, the amino group, and the N, N-dibutyl substituent.
Learn more about Bonds:
https://brainly.com/question/29282058
#SPJ11
Which of the following statements are correct regarding the deflection angles? Select all that apply. a) The sum of all the deflection angles in a route is 360° b) The deflection angle is between 0°
The correct option is a) The sum of all the deflection angles in a route is 360°.a) because a closed route forms a complete revolution.
When considering a closed route or polygon, the sum of all the deflection angles is indeed 360°. This is based on the fact that a complete revolution in a plane is equivalent to a rotation of 360 degrees. Each deflection angle represents a change in direction, and when you traverse a closed path, you return to your starting point, completing a full revolution.
Therefore, the sum of all the deflection angles must be 360°.
Learn more about deflection angles
brainly.com/question/33336926
#SPJ11
Suppose that on January 1 you have a balance of $4200 on a cresit card whose APR is 19%, which you want to pay off in 4 years Assume that you make no additional thanges to the card after January 1. a. Calculate your monthly payments. b. When the card is paid off, how much will you have paid since daneary 1 ? c. What percentage of your total payment (part b) is interest? a. The monthly payment in 5 (Do not round until the final anwwer. Then round to the nearest cent as needed)
Therefore, the monthly payments will be $110.70. The total amount paid will be $5313.60 when the card is paid off. The amount of interest paid is $1113.60, and the percentage of interest paid is 20.93%.
Given InformationBalance of the credit card on January 1 = $4200APR of the credit card = 19%Time to pay off the credit card = 4 years.
Formula UsedThe formula to calculate the monthly payment is,P = (A/i) * (1 - (1 + i)^-n)Where,P = Monthly Payment, A = Loan Amount,i = Interest Rate,n = Number of Payments,
Calculation of Monthly PaymentsWe have the following values,A = $4200i = 19% / 12 = 0.01583n = 4 * 12 = 48Using the above values in the formula, we get,
P = (4200/0.01583) * (1 - (1 + 0.01583)^-48).
The monthly payment is $110.70 (rounded to the nearest cent).
Calculation of Total Amount PaidAfter calculating the monthly payment, the total amount paid can be calculated using the following formula,
Total Amount Paid = Monthly Payment * Number of Payments Total Amount Paid ,
$110.70 * 48 = $5313.60
Calculation of Interest PaidThe interest paid is the difference between the total amount paid and the loan amount,
Interest Paid = Total Amount Paid - Loan AmountInterest Paid
$5313.60 - $4200 = $1113.60.
The percentage of interest paid is,Percentage of Interest Paid = (Interest Paid / Total Amount Paid) * 100Percentage of Interest Paid = (1113.60 / 5313.60) * 100 Percentage of Interest Paid = 20.93%
On January 1, the balance on a credit card is $4200 with an annual percentage rate of 19%. Suppose that you want to pay off the card in four years without making any additional charges after January 1.
To calculate the monthly payments, use the formula P = (A/i) * (1 - (1 + i)^-n), where P is the monthly payment, A is the loan amount, i is the interest rate, and n is the number of payments. We must first calculate i, which is the monthly interest rate, by dividing the annual percentage rate by 12. 19% divided by 12 is 0.01583. n equals the number of payments. In this situation, it is four years, which is the same as 48 months.
The monthly payment is $110.70 when the values are plugged into the formula.P = (4200/0.01583) * (1 - (1 + 0.01583)^-48) = $110.7
Using the formula for the total amount paid, which is Monthly Payment * Number of Payments, we can determine the total amount paid.
The total amount paid is calculated as follows:Total Amount Paid = Monthly Payment * Number of PaymentsTotal Amount Paid = $110.70 * 48 = $5313.60The total amount paid will be $5313.60 when the card is paid off.
The amount of interest paid is calculated by subtracting the loan amount from the total amount paid. So,Interest Paid = Total Amount Paid - Loan Amount Interest Paid = $5313.60 - $4200 = $1113.60.
The interest paid is $1113.60. To determine the percentage of interest paid, use the following formula:Percentage of Interest Paid = (Interest Paid / Total Amount Paid) * 100Percentage of Interest Paid = (1113.60 / 5313.60) * 100Percentage of Interest Paid = 20.93%
Therefore, the monthly payments will be $110.70. The total amount paid will be $5313.60 when the card is paid off. The amount of interest paid is $1113.60, and the percentage of interest paid is 20.93%.
To know more about interest rate visit:
brainly.com/question/28236069
#SPJ11
Mitch and Bill are both age 75. When Mitch was 22 years old, he began depositing $1200 per year into a savings account. He made deposits for the first 10 years, at which point he was forced to stop making deposits. However, he left his money in the account, where it continued to eam interest for the next 43 years Bil didn't start saving until he was 47 years old, but for the next 28 years he made annual deposits of $1200. Assume that both accounts earned an average annual retum of 5% (compounded once a year) Complete parts (a) through (d) below
a. How much money does Mitch have in his account at age 75?
At age 75, Mich has $
in his account.
b. How much money does Bill have in his account at age 75?
At age 75, Bill has 5 in his account.
c. Compare the amounts of money that Mitch and Bill deposit into their accounts.
Mitch deposits in his account and Bill deposits in his account.
d. Draw a conclusion about this parable. Choose the correct answer below
A. Both Bill and Mitch end with the same amount of money in their accounts, but Mitch had to deposit less money using his method. It is better to start saving as early as possible
B. Bill ends up with more money in his account than Mitch because he make more deposits than Mtch, and each additional deposit will accrue interest each year.
C. Mitch ends up with more money in his account despite not having deposited as much money as Bill because the interest that is initially accumulated accrues interest throughout the life of the account
D. Both Bill and Mitch have the same return on their investments despite using different methods of saving
a) Mitch has $65,055.97 in his account at age 75.
b) Bill has $89,901.98 in his account at age 75.
c) Mitch deposited $12,000 in his account, while Bill deposited $33,600 in his account.
d) Option (C) is correct.
Mitch ends up with more money in his account despite not having deposited as much money as
Bill because the interest that is initially accumulated accrues interest throughout the life of the account.
Therefore, it is better to start saving early.
a) We know that Mitch has been depositing $1200 per year for the first 10 years,
so he has deposited a total of $1200 * 10 = $12,000.
Now, this money has been in the account for the next 43 years.
Therefore, at the end of 43 years, the value of this money would have become:
$12,000 * (1 + 0.05) ^ 43 = $12,000 * 5.427164 = $65,055.97
Therefore, Mitch has $65,055.97 in his account at age 75.
b) Bill started depositing $1200 per year when he was 47 years old.
So, he has made annual deposits for the next 28 years.
Therefore, the total amount that Bill has deposited in his account would be:
$1200 * 28 = $33,600.
Now, this money has been in the account for the next 28 years.
Therefore, at the end of 28 years, the value of this money would have become:
$33,600 * (1 + 0.05) ^ 28 = $33,600 * 2.670824 = $89,901.98
Therefore, Bill has $89,901.98 in his account at age 75.
c) Mitch has deposited $12,000 in his account, while Bill has deposited $33,600 in his account.
d) Option (C) is correct. Mitch ends up with more money in his account despite not having deposited as much money as Bill because the interest that is initially accumulated accrues interest throughout the life of the account.
Therefore, it is better to start saving early.
To know more about interest visit:
https://brainly.com/question/3402162
#SPJ11
Assume that a sample is used to estimate a population proportion p. Find the 99% confidence interval for a sample of size 177 with 121 successes. Enter your answer as a tri-linear inequality using decimals (not percents) accurate to three decimal places.
< p <
Given a sample size of n = 177 and number of successes x = 121, the sample proportion would be p = x/n = 121/177 ≈ 0.6848.To find the 99% confidence interval, we will use the z-score corresponding to 99% confidence, which can be found using a standard normal distribution table or calculator.
We have: population
z = 2.576 (rounded to three decimal places) Using this z-score and the sample proportion,
we can find the margin of error (ME) as follows:
ME = z × √(p(1-p)/n)
= 2.576 × √(0.6848 × 0.3152/177)
≈ 0.0790
Finally, we can construct the confidence interval by adding and subtracting the margin of error from the sample proportion:
p ± ME = 0.6848 ± 0.0790 = (0.6058, 0.7638)
Therefore, the 99% confidence interval for a sample of size 177 with 121 successes is 0.606 < p < 0.764.
To know more about population proportion visit:
https://brainly.com/question/32523873
#SPJ11
Estimate the missing data for the * 10 points station x according to the following information using normal ratio method: Station Normal Annual ppt(cm) ppt(cm) A 44.1 4.3 B 36.8 3.5 C 47.2 4.8 X 37.5 px O ≈3.70 cm 3.847 cm ≈3.374 cm O 3.518 cm
The estimated missing data for station X using the normal ratio method is approximately 37.5 cm.
To estimate the missing data for station X using the normal ratio method, we need to compare the normal annual precipitation (ppt) of station X to the other stations (A, B, and C) and calculate the missing values accordingly. First, let's calculate the normal ratio for station X by dividing its normal annual ppt by the average of the normal annual ppt of the other three stations (A, B, and C).
Average ppt for stations A, B, and C: (44.1 + 36.8 + 47.2) / 3 = 42.7 cm
Normal ratio for station X: 37.5 cm / 42.7 cm = 0.878
Now, we can estimate the missing data for station X based on this normal ratio.
Estimated ppt for station X = Normal ratio * Average ppt of stations A, B, and C
Estimated ppt for station X = 0.878 * 42.7 cm = 37.5 cm
Note: The normal ratio method assumes that the relationship between stations remains relatively consistent. However, it's important to remember that this is an estimation and may not reflect the exact value.
More on missing data:
https://brainly.com/question/26177250
#SPJ11
Suppose you have an outdoor vegetable garden with dimensions 2 mx2 m. A storm lasting 1 hr delivers 0.8 inches of rain. a. What is the storm rainfall flux? Express your answer using each of the following units: m 2
hr
kgliquid water m 2
hr
lb liquid water m 2
hr
liters liquid water m 2
hr
gallons liquid water b. How much liquid water fell on your garden? Express your answer using each of the following units:
The storm rainfall flux is 0.00127 m2/hr, 1.27 kg liquid water/m2hr, 2.8 lb liquid water/m2hr, 1.27 liters liquid water/m2hr, and 0.335 gallons liquid water/m2hr. The amount of liquid water fell on the garden is 80.6 L, 21.3 gallons.
Dimensions of outdoor vegetable garden = 2 m × 2 m
Storm rainfall = 0.8 inches of rain
Time of storm = 1 hr(
a) The rainfall flux is the amount of rainfall per unit area and unit time. It is given as:
Rainfall flux = (Amount of rainfall) / (Area × Time)
Given the area of the garden is 2 m × 2 m, and the time is 1 hr, the rainfall flux is:
Rainfall flux = (0.8 inches of rain) / (2 m × 2 m × 1 hr)
Converting inches to meters, we get:
1 inch = 0.0254 m
Therefore,
Rainfall flux = (0.8 × 0.0254 m) / (2 m × 2 m × 1 hr) = 0.00127 m/hr
Converting the rainfall flux to other units:
In kg/hr:
1 kg of water = 1000 g of water
Density of water = 1000 kg/m3
So, 1 m3 of water = 1000 kg of water
So, 1 m2 of water of depth 1 m = 1000 kg of water
Therefore, 1 m2 of water of depth 1 mm = 1 kg of water
Therefore, the rainfall flux in kg/hr = (0.00127 m/hr) × (1000 kg/m3) = 1.27 kg/m2hr
In lbs/hr:
1 lb of water = 453.592 g of water
So, the rainfall flux in lbs/hr = (0.00127 m/hr) × (1000 kg/m3) × (2.20462 lb/kg) = 2.8 lbs/m2hr
In liters/hr:
1 m3 of water = 1000 L of water
So, 1 m2 of water of depth 1 mm = 1 L of water
Therefore, the rainfall flux in L/hr = (0.00127 m/hr) × (1000 L/m3) = 1.27 L/m2hr
In gallons/hr:
1 gallon = 3.78541 L
So, the rainfall flux in gallons/hr = (0.00127 m/hr) × (1000 L/m3) × (1 gallon/3.78541 L) = 0.335 gallons/m2hr
(b) To calculate the amount of water that fell on the garden, we need to calculate the volume of water.
Volume = Area × Depth.
The area of the garden is 2 m × 2 m.
We need to convert the rainfall amount to meters.
1 inch = 0.0254 m
Therefore, 0.8 inches of rain = 0.8 × 0.0254 m = 0.02032 m
Volume of water = Area × Depth = (2 m × 2 m) × 0.02032 m = 0.0806 m3
Converting the volume to other units:
In liters:
1 m3 of water = 1000 L of water
Therefore, the volume of water in liters = 0.0806 m3 × 1000 L/m3 = 80.6 L
In gallons:
1 gallon = 3.78541 L
Therefore, the volume of water in gallons = 80.6 L / 3.78541 L/gallon = 21.3 gallons.
Learn more about Rainfall:
https://brainly.com/question/1373907
#SPJ11