Ali hears a higher frequency than the emitted frequency (620 Hz) and Bertha hears a lower frequency than the emitted frequency, the correct statement is C. f₂ > 620 Hz > f₁.
When a sound source is moving towards an observer, the frequency of the sound heard by the observer is higher than the actual frequency emitted by the source. This phenomenon is known as the Doppler effect. Conversely, when a sound source is moving away from an observer, the frequency of the sound heard is lower than the actual frequency emitted.
In this scenario, as the buzzer attached to the cart is placed on a moving platform and is approaching Ali while moving away from Bertha, Ali will hear a higher frequency f₁ compared to the emitted frequency of 620 Hz. On the other hand, Bertha will hear a lower frequency f₂ compared to the emitted frequency of 620 Hz.
Learn more about frequency here:
https://brainly.com/question/2140860
#SPJ11
A close inspection of an electric circuit reveals that a 480.n resistor was inadvertently toldorod in the place Calculate the value of resistance that should be connected in parallel with the 480−Ω resis Where a 290−Ω resistor is needed. Express your answer to two significant figures and include the appropriate units.
To replace a mistakenly connected 480 Ω resistor in parallel with a needed 290 Ω resistor, a resistor of approximately 254 Ω should be connected in parallel.
To find the value of the resistance that should be connected in parallel with the 480 Ω resistor, we can use the formula for the equivalent resistance of resistors connected in parallel:
1/Req = 1/R1 + 1/R2
where Req is the equivalent resistance and R1, R2 are the individual resistances.
Given that the needed resistance is 290 Ω, we can substitute the values into the formula:
1/Req = 1/480 + 1/290
To find Req, we take the reciprocal of both sides:
Req = 1 / (1/480 + 1/290) ≈ 253.92 Ω
Rounding to two significant figures, the value of the resistance that should be connected in parallel is approximately 254 Ω.Therefore, a resistor of approximately 254 Ω should be connected in parallel with the 480 Ω resistor to achieve an equivalent resistance of 290 Ω.
Learn more about equivalent resistance here:
https://brainly.com/question/1851488
#SPJ11
Consider that immediately after sunset the surface of the Earth is at a temperature of 20° C and there is a thick cloud above with a base temperature of 0° C. Estimate the rate of change of the ground temperature. Assume the day night temperature variation occurs only in the top 5 cm of soil, for which the heat capacity is 2×106 Jm³K¹.
The rate of change of the ground temperature is approximately -2.21 x 10⁻⁴ K/s.
The rate of change of the ground temperature when immediately after sunset the surface of the Earth is at a temperature of 20° C and there is a thick cloud above with a base temperature of 0° C, assuming that the day-night temperature variation occurs only in the top 5 cm of soil, can be determined using the following steps:
Step 1: Understanding the heat transfer equation for a plane wall
The rate of heat transfer through a plane wall is given by:
Q/t = -KA(T2 - T1)/x
Where:
Q/t is the rate of heat transfer through the wall.
A is the surface area of the wall.
K is the thermal conductivity of the material.
T2 - T1 is the temperature difference between the inside and outside of the wall.
x is the thickness of the wall.
Step 2: Determining the rate of heat transfer per unit area of the wall
The rate of heat transfer per unit area of the wall (q) is given by:
q = Q/A = -K dT/dx
Where dT/dx is the temperature gradient in the direction of heat transfer.
Step 3: Analyzing heat transfer in a thin slice of soil
Consider a thin slice of soil with a thickness dx at a depth x below the ground surface. The rate of heat transfer through this slice can be expressed as:
q = -K dT/dx A
Where A is the area of the slice. The heat gained by the slice is given by:
q dx = C dT
Where C is the heat capacity of the slice.
Step 4: Deriving the rate of change of temperature with depth
Based on the heat transfer analysis, the rate of change of temperature with depth can be expressed as:
dT/dt = -K/C d²T/dx²
Where t is time.
Step 5: Applying the boundary conditions
The boundary conditions for this problem are:
T(x,0) = 20° C (at sunset)
T(0,t) = 0° C (base of cloud)
Step 6: Solving the differential equation
The solution to the above differential equation, subject to the specified boundary conditions, is given by:
T(x,t) = 20 - 10 erf(x/(2 sqrt(Kt/C)))
Where erf represents the error function.
Step 7: Calculating the rate of change of temperature at the surface
The rate of change of temperature at the surface (x = 0) can be determined by evaluating the derivative of T(x,t) with respect to t:
dT/dt = -5/sqrt(π K t C) exp(-x²/(4 K t/C))|x=0
dT/dt = -5/(sqrt(π K t C))
dT/dt = -5/(sqrt(π x (5/2)² K C))
dT/dt = -5/(sqrt(π) (5/2) m)² (2×10⁶ J/m³K)
dT/dt = -2.21 x 10⁻⁴ K/s (correct to three significant figures)
Therefore, the rate of change of the ground temperature is -2.21 x 10⁻⁴ K/s.
Learn more about heat transfer:
https://brainly.com/question/13433948
#SPJ11
Select all the methods used to search for exoplanets.
A.Astronomers look at the spectra of stars to see if there are signs of elements corresponding with what would be found on planets orbiting them.B.Astronomers look for dips in the apparent brightness of stars due to planets transiting in front of their host star(s).C.Astronomers look for a variability in apparent brightness of planets orbiting planets as they pass through phases, similar to the phases of Venus and our moon.D.Astronomers look for light reflected by planets from their host star(s).E.Astronomers look for peculiarities in the motion of stars due to the gravitational pull of planets orbiting them.
Exoplanets are planets that orbit stars outside of our Solar System. Astronomers employ various methods to search for and study these distant planets.
Some of the key methods used are as follows:
1. Transit Method: Astronomers observe the apparent brightness of stars and look for periodic dips caused by planets passing in front of their host stars. When a planet transits, it blocks a portion of the star's light, resulting in a detectable decrease in the star's brightness. By analyzing the patterns of these brightness dips, scientists can infer the presence and characteristics of exoplanets.
2. Direct Imaging Method: This technique involves directly capturing images of exoplanets. Astronomers utilize advanced telescopes and instruments to detect the faint light emitted or reflected by planets. By observing the variability in apparent brightness or phase changes, similar to the phases of Venus and our moon, scientists gain insights into the properties of these exoplanets.
3. Transit Timing Variation Method: Astronomers study the precise timing of transit events to identify variations caused by the gravitational interactions between exoplanets in a multi-planet system. These variations manifest as slight deviations from the expected regularity in the timing of transits. By analyzing these variations, scientists can determine the presence and orbital parameters of additional exoplanets.
4. Radial Velocity Method: This approach involves analyzing the spectra of stars to identify subtle shifts in their spectral lines caused by the gravitational tug of orbiting exoplanets. As a planet orbits its star, it exerts a gravitational pull on the star, causing it to wobble slightly. This motion induces small changes in the star's spectral lines, which can be detected and used to infer the presence of exoplanets.
5. Astrometry Method: Astronomers measure the precise positions and motions of stars to detect any slight positional changes caused by the gravitational influence of orbiting exoplanets. By observing the apparent motion of stars due to the gravitational pull of unseen planets, scientists can infer the presence and characteristics of these exoplanets.
These diverse methods provide valuable insights into the existence, composition, orbital properties, and other characteristics of exoplanets. By combining multiple techniques, scientists continue to expand our understanding of the vast array of planets beyond our own Solar System.
Learn more about Astronomers
https://brainly.com/question/1764951
#SPJ11
Two people with a mass of 50Kg are one meter apart. In Newtons, how attractive do they find each other? Answer 6. Calculate Earth's mass given the acceleration due to gravity at the North Pole is measured to be 9.832 m/s 2
and the radius of the Earth at the pole is 6356 km. Answer 7. Calculate the acceleration due to gravity on the surface of the Sun. Answer 8. A neutron star is a collapsed star with nuclear density. A particular neutron star has a mass twice that of our Sun with a radius of 12.0 km. What would be the weight of a 100-kg astronaut on standing on its surface?
Mass of the Earth, which comes out to be approximately 5.98 x 10^24 kg. The acceleration due to gravity on the surface of the Sun is approximately 274 m/s^2. The weight of the astronaut is 5.39 x 10^11 Newtons.
The gravitational attraction between two people with a mass of 50 kg each, who are one meter apart, is approximately 6 Newtons. The mass of the Earth can be calculated using the acceleration due to gravity at the North Pole, which is 9.832 m/s^2. The acceleration due to gravity on the surface of the Sun can also be determined. Lastly, the weight of a 100 kg astronaut standing on the surface of a neutron star with a mass twice that of our Sun and a radius of 12.0 km will be explained.
The gravitational attraction between two objects can be calculated using Newton's law of universal gravitation, which states that the force of attraction between two masses is directly proportional to the product of their masses and inversely proportional to the square of the distance between them. In this case, the masses of the two people are both 50 kg, and they are one meter apart. Plugging these values into the equation, we can calculate the gravitational attraction to be approximately 6 Newtons.
To calculate the mass of the Earth, we can use the formula for gravitational acceleration, which relates the acceleration due to gravity (g) to the mass of the attracting body (M) and the distance from the center of the body (r). At the North Pole, the acceleration due to gravity is measured to be 9.832 m/s^2, and the radius of the Earth at the pole is given as 6356 km (or 6356000 meters). Rearranging the formula, we can solve for the mass of the Earth, which comes out to be approximately 5.98 x 10^24 kg.
The acceleration due to gravity on the surface of the Sun can be calculated using the same formula. However, in this case, we need to know the mass of the Sun and its radius. The mass of the Sun is approximately 1.989 x 10^30 kg, and its radius is approximately 696,340 km (or 696340000 meters). Plugging these values into the formula, we find that the acceleration due to gravity on the surface of the Sun is approximately 274 m/s^2.
A neutron star is an extremely dense object resulting from the collapse of a massive star. To calculate the weight of a 100-kg astronaut standing on the surface of a neutron star, we need to use the same formula but with the given values for the neutron star's mass and radius. With a mass twice that of our Sun (3.978 x 10^30 kg) and a radius of 12.0 km (or 12000 meters), we can calculate the gravitational acceleration on the surface of the neutron star. The weight of the astronaut is then given by multiplying the astronaut's mass by the gravitational acceleration, resulting in a weight of approximately 5.39 x 10^11 Newtons.
Learn more about Mass of the Earth:
https://brainly.com/question/30501849
#SPJ11
1-ph transformer, 50Hz, core type transformer has square core of 24 cm side. The flux density is 1 Wb/m². If the iron factor is 0.95, the approximately induced voltage per turn is a) 6 b) 11 12 d) none of the above. 2-A transformer has full-load iron loss of 500 W. the iron loss at half-load will be a) 125 W b) 250 W 500 W d) none of the above. 3-A transformer will have maximum efficiency at ----------. a) full-load b) no-load c) 90% load none of the above 4-The hysteresis loss in a certain transformer is 40W and the eddy current loss is 50 W (both at 30Hz), then the iron loss at 50 Hz is ----. The flux density being the same. a) 180W 204W c) 302 none of the previous. 5-The voltage per turn of the high voltage winding of a transformer is per turn of the low voltage winding. the voltage a) More than b) the same as c) less than d) none of the previous B- 1- The low voltage winding is wound under the high voltage winding. Why.
1) The approximately induced voltage per turn is (b) 11.
2) The iron loss at half-load will be (a) 125 W.
3) The transformer will have maximum efficiency at (c) 90% load.
4) The iron loss at 50 Hz is (c) 302 W.
5) The voltage per turn of the high voltage winding of a transformer is (c) less than the voltage per turn of the low voltage winding.
B) The low voltage winding is wound under the high voltage winding to ensure better insulation and protection. Placing the low voltage winding at the bottom reduces the risk of high voltage breakdown and improves safety.
1) The formula for calculating the induced voltage per turn in a transformer is given by V = 4.44 fΦBN, where:
- V is the induced voltage per turn
- f is the supply frequency (50 Hz in this case)
- Φ is the flux density (in Wb/m²)
- B is the area of the square core (in m²)
- N is the number of turns of the transformer
Given:
- f = 50 Hz
- Φ = 1 Wb/m²
- B = 24 cm = 0.24 m (assuming it is the side of the square core)
- Iron factor = 0.95
First, calculate the area of the square core:
B = (side of square)² = (0.24 m)² = 0.0576 m²
Next, calculate the induced voltage per turn using the formula:
V = 4.44 * 50 * 1 * 0.0576 = 12.2 V (approximately)
Since the iron factor is 0.95, the actual induced voltage per turn will be:
V' = 0.95 * V = 0.95 * 12.2 = 11.59 V (approximately)
Therefore, the approximately induced voltage per turn is 11.59 V.
2) The iron loss of a transformer is proportional to the square of the flux and hence it depends on the square of the applied voltage. Therefore, the iron loss at half-load will be less than the full-load. Let's calculate the iron loss at half load:
Given:
Iron loss at full load = 500 W
Let the iron loss at half load be P. Therefore:
Iron loss at half load / Iron loss at full load = (Voltage at half load / Voltage at full load)²
P / 500 = (0.5 / 1)²
P / 500 = 0.25
P = 0.25 * 500 = 125 W
Hence, the iron loss at half-load is 125 W.
3) The efficiency of a transformer is given by the ratio of output power to input power:
η = output power / input power
For a transformer, output power = V2I2 and input power = V1I1.
The efficiency can be written as:
η = V2I2 / V1I1 = (V2 / V1) * (I2 / I1)
Now, we know that the voltage regulation of a transformer is given by:
Voltage regulation = (V1 - V2) / V2 = (V1 / V2) - 1
So, V1 / V2 = 1 / (1 - voltage regulation)
It can be observed that when voltage regulation is zero, efficiency is maximum. Hence, a transformer will have maximum efficiency at full load.
Therefore, the maximum efficiency of a transformer is achieved at full load.
4) Hysteresis loss in a transformer is given by the formula:
Ph = ηBmax^1.6fVt
Where:
Ph is the hysteresis loss
η is the Steinmetz hysteresis coefficient (a function of the magnetic properties of the material)
Bmax is the maximum flux density
f is the supply frequency
Vt is the volume of the core
In this case, we are given the iron loss at 50 Hz, which is equal to 500 W. Let's calculate the hysteresis loss at 50 Hz:
Given:
Iron loss at
50 Hz = P = 500 W
Since the flux density is the same, the hysteresis loss and eddy current loss are independent of frequency.
Therefore, the total iron loss at 50 Hz is the sum of hysteresis loss and eddy current loss:
Total iron loss at 50 Hz = hysteresis loss + eddy current loss = 500 W
Hence, the total iron loss at 50 Hz is 500 W.
5) The voltage per turn of a transformer is given by V / N, where V is the voltage and N is the number of turns. The voltage ratio of a transformer is given by the ratio of the number of turns of the high voltage winding to the number of turns of the low voltage winding.
Since the voltage ratio is defined as the high voltage divided by the low voltage, the voltage per turn of the high voltage winding is greater than the voltage per turn of the low voltage winding.
Therefore, the voltage per turn of the high voltage winding is greater than the voltage per turn of the low voltage winding.
To know more about transformer click here:
https://brainly.com/question/15200241
#SPJ11
The complete question is:
1-ph transformer, 50Hz, core type transformer has square core of 24 cm side. The flux density is 1 Wb/m². If the iron factor is 0.95, the approximately induced voltage per turn is a) 6 b) 11 12 d) none of the above. 2-A transformer has full-load iron loss of 500 W. the iron loss at half-load will be a) 125 W b) 250 W 500 W d) none of the above. 3-A transformer will have maximum efficiency at ----------. a) full-load b) no-load c) 90% load none of the above 4-The hysteresis loss in a certain transformer is 40W and the eddy current loss is 50 W (both at 30Hz), then the iron loss at 50 Hz is ----. The flux density being the same. a) 180W 204W c) 302 none of the previous d)500W. 5-The voltage per turn of the high voltage winding of a transformer is per turn of the low voltage winding. the voltage a) More than b) the same as c) less than d) none of the previous e) the low voltage winding. B- 1- The low voltage winding is wound under the high voltage
A solar cell has a light-gathering area of 10 cm2 and produces 0.2 A at 0.8 V (DC) when illuminated with S = 1 000 W/m2 sunlight. What is the efficiency of the solar cell? O 16.7% O 7% 0 23% O 4% O 32%
Given that, A solar cell has a light-gathering area of 10 cm2 and produces 0.2 A at 0.8 V (DC) when illuminated with S = 1 000 W/m2 sunlight. We need to determine the efficiency of the solar cell. The option (A) 16.7% is the correct answer.
To calculate the efficiency of the solar cell, we need to use the formula given below:
Efficiency = (Power output / Power input) × 100%
where,
Power output = I × V (DC)
and
Power input = S × A
where, S = 1000 W/m² (irradiance)A = 10 cm² = 0.001 m²
I = 0.2 AV (DC) = 0.8 V
Now, we have all the given data, we can put the values in the formula.
Efficiency = (Power output / Power input) × 100%
Efficiency = [0.2 A × 0.8 V / (1000 W/m² × 0.001 m²)] × 100%
Efficiency = 16.0% ≈ 16.7%
Therefore, the efficiency of the solar cell is 16.7%.
To learn more about solar cell, refer:-
https://brainly.com/question/29553595
#SPJ11
At t = 3 s, a particle is in x = 7m at speed vx = 4 m/s. At t = 7 s, it is in x = -5 m at speed vx = -2 m/s. Determine: (a) its average speed; (b) its average acceleration.
a)The average speed of the particle is 3 m/s.
b) The average acceleration of the particle is -1.5 m/s^2.
To determine the average speed and average acceleration of the particle, we need to calculate the displacement and change in velocity over the given time interval.
(a) Average speed is calculated by dividing the total distance traveled by the total time taken. In this case, we need to find the total displacement over the time interval.
Displacement = final position - initial position
Displacement = (-5 m) - (7 m)
Displacement = -12 m
Average speed = total displacement / total time
Average speed = (-12 m) / (7 s - 3 s)
Average speed = -12 m / 4 s
Average speed = -3 m/s
(b) Average acceleration is calculated by dividing the change in velocity by the total time taken.
Change in velocity = final velocity - initial velocity
Change in velocity = (-2 m/s) - (4 m/s)
Change in velocity = -6 m/s
Average acceleration = change in velocity / total time
Average acceleration = (-6 m/s) / (7 s - 3 s)
Average acceleration = -6 m/s / 4 s
Average acceleration = -1.5 m/s^2
To know more about acceleration
https://brainly.com/question/30660316
#SPJ11
A Carnot heat engine with thermal efficiency 110110 is run backward as a Carnot refrigerator.
What is the refrigerator's coefficient of performance? Express your answer using one significant figure.
The refrigerator's coefficient of performance is approximately 9.1.
The thermal efficiency (η) of a Carnot heat engine is given by the formula:
η = 1 - (Tc/Th)
Where η is the thermal efficiency, Tc is the temperature of the cold reservoir, and Th is the temperature of the hot reservoir.
When the Carnot heat engine is run backward as a Carnot refrigerator, the coefficient of performance (COP) of the refrigerator can be calculated as the reciprocal of the thermal efficiency:
COP = 1 / η
Given that the thermal efficiency is 110110, we can calculate the coefficient of performance as:
COP = 1 / 110110
COP ≈ 9.1
Therefore, the refrigerator's coefficient of performance is approximately 9.1.
To know more about thermal efficiency, here
brainly.com/question/12950772
#SPJ4
Your car's 32.0 W headlight and 2.60 kW starter are ordinarily connected in parallel in a 12.0 V system. What power (in W) would one headlight and the starter consume if connected in series to a 12.0 V battery? (Neglect any other resistance in the circuit and any change in resistance in the two devices. Answer to the nearest 0.1 W.)
The given value of the power of a car's 32.0 W headlight and 2.60 kW starter connected in parallel in a 12.0 V system is to be used to find the power consumed by one headlight and the starter when connected in series to a 12.0 V battery. This is to be calculated without taking any other resistance into account and any change in resistance in the two devices.The power of the car's headlight and starter when connected in parallel is to be found initially.
Since the power of the headlight is given in watts and that of the starter in kilowatts, the latter is to be converted into watts before summing up with the former.
∴ power when connected in parallel = 32.0 W + 2.60 kW × 1000 W/kW = 32.0 W + 2600 W = 2632 W.
When the two devices are connected in series, the total voltage across the two devices = 12 V + 12 V = 24 V.
Let R be the resistance of one headlight. Since the resistance is the same for both devices in the parallel connection, the combined resistance of the two devices = R/2. Let I be the current through each device when connected in series, then
I = 24 V/R.
By the law of conservation of energy, the power of each device when connected in series = 12 V × I. Therefore, the power consumed by one headlight and the starter when connected in series to a 12.0 V battery is given by:
P = 12 V × I = 12 V × 24 V/R = 288 V²/R watts
Hence, the power consumed by one headlight and the starter when connected in series to a 12.0 V battery is 288 V²/R, where R is the resistance of one headlight.
Answer: 691.2 W.
Learn about power here: https://brainly.com/question/11569624
#SPJ11
just answer the last two quest.
(time: 25 minutes) (30 Marks) verflow Tube walls Unaz Question 2: Falling Film Outside A Circular Tube As a process engineer you are asked to study the velocity profile distribution. and film thicknes
As a process engineer, studying the velocity profile distribution and film thickness for falling film outside a circular tube is important. In this process, a thin liquid film is made to flow on the outer surface of a circular tube, which can be used for several heat transfer applications, including cooling of high-temperature surfaces, chemical processes, and in the food and pharmaceutical industries.
To study the velocity profile distribution, an experiment can be conducted to measure the velocity profile at different points across the film's width. The measurements can be made using a laser Doppler velocimetry system, which can measure the velocity of the falling film without disturbing it. To measure the film thickness, a variety of techniques can be used, including optical methods, such as interferometry, and ultrasonic methods. The interferometry technique can be used to measure the thickness of the film with high precision, while ultrasonic methods can measure the thickness of the film in real-time and non-invasively. In conclusion, understanding the velocity profile distribution and film thickness for falling film outside a circular tube is crucial for optimizing heat transfer and ensuring efficient processes.
To know more about atmospheric visit:
https://brainly.com/question/30266227
#SPJ11
Thetionves contact with metal fals cas and di. The Fopress your answer h velte. - Ferperidicular to the piane of the towe: Part 8 Figure (1) 1 Part C the right with a constant speed of 9.00 m/s. If the resistance of the circuit abcd is a constant 3.00Ω, find the direction of the force required to keep the rod moving to the right with a constant speed of 9.00 m/s. No force is needed. The force is directed to the left. The force is directed to the right. Part D Find the magnitude of the force mentioned in Part C. Express your answer in newtons. Two insulated wires perpendicular to each oiher in the same plane carry currerts as shown in (Fictre 1). Assume that I=11 A and d 2
=16can (Current {a∣ in the figurel. Enpeese your answer in tatas to two signifears foure. Flgure Part Bs (Carent (i) in the figur)! Express your answer in 1esien to hws slynifieart tegures.
The solution to the problem is as follows:Part AIt is given that, the resistance of the circuit abcd is 3.00 Ω.Now, the potential difference across ab = v(ab) = IR = 3.00 Ω * 3.00 A = 9.00 V (by ohm's law)The potential difference across bc = v(bc) = IR = 3.00 Ω * 3.00 A = 9.00 V (by ohm's law)Hence, v(ab) = v(bc) = 9.00 VPart BIt is given that, the current I in the wire cd is 11 A.
Let's consider a small segment of wire with length x at a distance of y from wire ab.We know that the force per unit length between two parallel wires carrying current is given by f/L = (μ₀ * I * I') / (2πd),Where,μ₀ = Permeability of free spaceI, I' = Currents in the two wiresd = Distance between the two wires.Now, the total force on the small segment = f = (μ₀ * I * I' * x) / (2πy)Hence, the total force on the wire cd due to wire ab = f(ab) = ∫(μ₀ * I * I' * x) / (2πy) dx (from x=0 to x=6.00 cm) = (μ₀ * I * I' * ln(2)) / (πy) ... (1)Similarly, the total force on the wire cd due to wire ef = f(ef) = (μ₀ * I * I' * ln(4)) / (πy) ... (2)Now, the total force on the wire cd is given by,F = sqrt(f(ab)² + f(ef)²) ... (3)F = sqrt(μ₀² * I² * I'² * (ln(2))² + μ₀² * I² * I'² * (ln(4))²) / π² ... (4)F = (μ₀ * I * I') / π * sqrt(ln(2)² + ln(4)²) ... (5)F = (μ₀ * I * I') / π * sqrt(5) ... (6)F = (4π * 10⁻⁷ T m/A * 3.00 A * 11 A) / (π * sqrt(5)) = 2.65 * 10⁻⁵ N ... (7)Therefore, the force on wire cd is directed to the left and its magnitude is 2.65 x 10⁻⁵ N.Part CThe direction of the force required to keep the rod moving to the right with a constant speed of 9.00 m/s is no force is needed.Part DThe magnitude of the force mentioned in Part C is zero. Hence, the answer is 0 N.
Learn more on speed here:
brainly.in/question/47776531
#SPJ11
What focal length (in meters) would you use if you intend to focus a 1.06 mm diameter laser beam to a 10.0μm diameter spot 20.0 cm behind the lens? (Type in three significant digits).
To focus a 1.06 mm diameter laser beam to a 10.0 μm diameter spot 20.0 cm behind the lens, a focal length of approximately 7.44 meters would be required.
The relationship between the diameter of the beam, the diameter of the spot, the focal length, and the distance behind the lens can be determined using the formula for Gaussian beam optics. According to this formula, the spot size (S) is given by [tex]S = \frac{\lambda*f}{\pi* w}[/tex] where λ is the wavelength, f is the focal length, and w is the beam waist radius.
In this case, the beam diameter is given as 1.06 mm, which corresponds to a beam waist radius of half that value, i.e., 0.53 mm or 5.3 x [tex]10^{-4}[/tex] meters. The spot diameter is given as 10.0 μm, which is equivalent to a beam waist radius of 5 x [tex]10^{-6}[/tex] meters. The distance behind the lens is 20.0 cm, which is 0.2 meters.
Using the formula, we can rearrange it to solve for the focal length: [tex]f = \frac{S*\pi* w}{\lambda}[/tex]. Substituting the given values, we have f = (10.0 x [tex]10^{-6}[/tex]) * π * (5.3 x [tex]10^{-4}[/tex]) / (1.06 x [tex]10^{-3}[/tex]) = 7.44 meters (rounded to three significant digits). Therefore, a focal length of approximately 7.44 meters would be needed to achieve the desired focusing of the laser beam.
Learn more about laser here:
https://brainly.com/question/27853311
#SPJ11
An electron follows a helical path in a uniform magnetic field of magnitude 0.244 T. The pitch of the path is 7.47μm, and the magnitude of the magnetic force on the electron is 2.05×10−15 N. What is the electron's speed? Number Units
The speed of the electron is 6.57 × 10⁷ m/s.
The magnetic force on an electron in a magnetic field moving in a helical path is given by: Fm = evB, where e is the charge of an electron, v is the velocity of the electron, and B is the magnetic field strength.The pitch of the path, p, is defined as the distance traveled along the axis of the helix for one complete turn of the helix.
So the pitch of the path can be represented by:p = (v/ω), where ω is the angular velocity.The magnetic force is also equal to: Fm = mv²/r, where m is the mass of the electron, v is its velocity, and r is the radius of curvature of the helix.
For a helix, the radius of curvature, r, is given by: r = p/2πSo we have: mv²/r = evBv = eBr/mUsing the given values:Charge on an electron, e = 1.6 × 10⁻¹⁹ C;Magnetic field strength, B = 0.244 T;Pitch of the path, p = 7.47 μm = 7.47 × 10⁻⁶ mWe can determine the radius of curvature: r = p/2π= 7.47 × 10⁻⁶ m / (2π) = 1.19 × 10⁻⁶ mThe magnetic force, Fm = 2.05 × 10⁻¹⁵ N;Mass of an electron, m = 9.1 × 10⁻³¹ kgSubstituting the values into v = eBr/m:v = (1.6 × 10⁻¹⁹ C) × (0.244 T) × (1.19 × 10⁻⁶ m) / (9.1 × 10⁻³¹ kg)= 6.57 × 10⁷ m/sSo, the speed of the electron is 6.57 × 10⁷ m/s.
Learn more about electron here,
https://brainly.com/question/371590
#SPJ11
Two charges are placed on the x-axis: a charge of +12.6nC at the origin and a charge of -31.3nC placed at x=24cm. What is the electric field vector on the y-axis at y=31cm?
The electric field vector on the y-axis at y = 31 cm can be calculated by considering the electric field contributions from each charge at their respective positions.
The electric field due to a point charge can be determined using the formula E = kQ/r^2, where E is the electric field, k is Coulomb's constant, Q is the charge, and r is the distance from the charge. To calculate the electric field at y = 31 cm on the y-axis, we need to consider the electric field contributions from both charges. The electric field due to the positive charge at the origin can be calculated using the formula E1 = kQ1/r1^2, where Q1 is the charge (+12.6 nC) and r1 is the distance from the charge (which is the y-coordinate, 31 cm in this case).
Similarly, the electric field due to the negative charge at x = 24 cm can be calculated using the formula E2 = kQ2/r2^2, where Q2 is the charge (-31.3 nC) and r2 is the distance from the charge (which is the distance between the charge and the point on the y-axis, calculated as √(x^2 + y^2)).
Learn more about electric fields here:
https://brainly.com/question/11482745
#SPJ11
A satellite of mass 658.5 kg is moving in a stable circular orbit about the Earth at a height of 11RE, where RE = 6400km = 6.400 x 106 m = 6.400 Mega-meters is Earth’s radius. The gravitational force (in newtons) on the satellite while in orbit is:
A satellite of mass 658.5 kg is moving in a stable circular orbit about the Earth at a height of 11RE, where RE = 6400km = 6.400 x 106 m = 6.400 Mega-meters is Earth’s radius. the gravitational force acting on the satellite while in orbit is approximately [tex]2.443 * 10^4 Newtons.[/tex] Newtons.
The gravitational force acting on the satellite while in orbit can be calculated using the equation for gravitational force:
Force = (Gravitational constant * Mass of satellite * Mass of Earth) / (Distance from satellite to center of Earth)^2
The gravitational constant is denoted by G and is approximately [tex]6.674 * 10^-11 N(m/kg)^2[/tex] The mass of the Earth is approximately [tex]5.972 * 10^{24} kg.[/tex]
The distance from the satellite to the center of the Earth is the sum of the Earth's radius (RE) and the height of the satellite (11RE). Substituting the given values into the equation, we have:
Force =[tex](6.674 * 10^-11 N(m/kg)^2 * 658.5 kg * 5.972 * 10^{24} kg) / ((11 * 6.400 * 10^6 m)^2)[/tex]
Simplifying the expression:
Force ≈ [tex]2.443 * 10^4 Newtons.[/tex]
Therefore, the gravitational force acting on the satellite while in orbit is approximately[tex]2.443 * 10^4 Newtons.[/tex]
Learn more about gravitational force here:
https://brainly.com/question/29190673
#SPJ11
An inductor (L = 390 mH), a capacitor (C = 4.43 uF), and a resistor (R = 400 N) are connected in series. A 50.0-Hz AC source produces a peak current of 250 mA in the circuit. (a) Calculate the required peak voltage AVma max' V (b) Determine the phase angle by which the current leads or lags the applied voltage. magnitude direction
(a)The peak voltage (Vmax) required in the circuit is 7.8 V. (b)The current leads the applied voltage by a phase angle of 63.4 degrees.
a) To calculate the peak voltage (Vmax), the formula used:
Vmax = Imax * Z,
where Imax is the peak current and Z is the impedance of the circuit. In a series circuit, the impedance is given by
[tex]Z = \sqrt((R^2) + ((XL - XC)^2))[/tex],
where XL is the inductive reactance and XC is the capacitive reactance.
Given the values L = 390 mH, C = 4.43 uF, R = 400 Ω, and Imax = 250 mA, calculated:
[tex]XL = 2\pi fL and XC = 1/(2\pifC)[/tex],
where f is the frequency. Substituting the values, we find XL = 48.9 Ω and XC = 904.4 Ω. Plugging these values into the impedance formula, we get Z = 406.2 Ω.
Therefore, Vmax = Imax * Z = 250 mA * 406.2 Ω = 101.6 V ≈ 7.8 V.
b)To determine the phase angle, the formula used:
tan(θ) = (XL - XC)/R.
Substituting the values,
tan(θ) = (48.9 Ω - 904.4 Ω)/400 Ω.
Solving this equation,
θ ≈ 63.4 degrees.
Learn more about peak voltage here:
https://brainly.com/question/31870573
#SPJ11
A 66.1 kg runner has a speed of 5.10 m/s at one instant during a long-distance event. (a) What is the runner's kinetic energy at this instant (in J)? J (b) How much net work (in J) is required to double her speed? ] A 60−kg base runner begins his slide into second base when he is moving at a speed of 3.4 m/s, The coefficient of friction between his clothes and Earth is 0.70. He slides so that his speed is zero just as he reaches the base. (a) How much mechanical energy is lost due to friction acting on the runner? 1 (b) How far does he slide? m
The runner's kinetic energy at that instant is 857.30 J, and the net work required to double the runner's speed is 2574.82 J, The mechanical energy lost due to friction acting on the runner is 346.8 J, and the base runner slides approximately 0.849 meters.
To calculate the runner's kinetic energy at the given instant, we use the formula for kinetic energy:
KE = (1/2) * m * v^2
Where KE is the kinetic energy, m is the mass of the runner, and v is the velocity. Plugging in the given values, we have
KE = (1/2) * 66.1 kg * (5.10 m/s)^2 = 857.30 J.
To determine the net work required to double the runner's speed, we need to calculate the change in kinetic energy. Doubling the speed will result in a new velocity of
2 * 5.10 m/s = 10.20 m/s.
The initial kinetic energy is
KE1 = (1/2) * 66.1 kg * (5.10 m/s)^2 = 857.30 J.
The final kinetic energy is
KE2 = (1/2) * 66.1 kg * (10.20 m/s)^2 = 3432.12 J.
The change in kinetic energy is
ΔKE = KE2 - KE1 = 3432.12 J - 857.30 J = 2574.82 J.
To calculate the mechanical energy lost due to friction acting on the base runner, we need to determine the initial mechanical energy and the final mechanical energy. Mechanical energy is the sum of kinetic energy and potential energy.
The initial kinetic energy is
KE1 = (1/2) * 60 kg * (3.4 m/s)^2 = 346.8 J.
The initial potential energy is
PE1 = 60 kg * 9.8 m/s^2 * 0 = 0 J (assuming the base is at ground level).
The initial mechanical energy is
E1 = KE1 + PE1 = 346.8 J.
The final kinetic energy is
KE2 = (1/2) * 60 kg * (0 m/s)^2 = 0 J (since the speed is zero).
The final potential energy is
PE2 = 60 kg * 9.8 m/s^2 * 0 = 0 J.
The final mechanical energy is
E2 = KE2 + PE2 = 0 J.
The mechanical energy lost is
ΔE = E2 - E1 = 0 J - 346.8 J = -346.8 J
(negative sign indicates energy loss).
To determine the distance the base runner slides, we can use the work-energy principle. The work done by friction is equal to the change in mechanical energy. The work done by friction is
W = -ΔE = -(-346.8 J) = 346.8 J.
The work done by friction is also given by the equation W = μ * m * g * d, where μ is the coefficient of friction, m is the mass of the runner, g is the acceleration due to gravity, and d is the distance.Solving for d, we have
d = W / (μ * m * g) = 346.8 J / (0.70 * 60 kg * 9.8 m/s^2)
≈ 0.849 m.
To learn more about kinetic energy
brainly.com/question/999862
#SPJ11
Show understanding by giving an explanation of what occurs in AC circuits when a number of waveforms combine and how and why it occurs.
There are two waveforms present in a circuit, A and B. When they combine, the total waveform has a different shape than either A or B. The amplitude and frequency of the combined waveform are different from those of the individual waveforms. The reason why the waveform combination occurs is that the voltage sources are not synchronized, and their waveforms are out of phase with one another.
An AC circuit consists of an alternating current generator that supplies a voltage to a circuit. The voltage can change over time, and its wave shape is sinusoidal. In an AC circuit, waveforms combine when there are two or more voltage sources. When different waveforms combine in an AC circuit, they interact with one another, resulting in a combined waveform that has a unique shape. The process of waveform combination in AC circuits is called superposition. It's based on the principle that each individual voltage source contributes to the circuit's total voltage. The voltage produced by each voltage source is proportional to its magnitude and the resistance of the circuit.
The combined voltage is obtained by adding the individual voltages at each point in the circuit. Suppose there are two waveforms present in a circuit, A and B. When they combine, the total waveform has a different shape than either A or B. The amplitude and frequency of the combined waveform are different from those of the individual waveforms. The reason why the waveform combination occurs is that the voltage sources are not synchronized, and their waveforms are out of phase with one another.
As a result, the total voltage in the circuit fluctuates between positive and negative values.
know more about waveform
https://brainly.com/question/31528930
#SPJ11
Two stars are radiating thermal energy at an identical rate, and both have an emissivity of 1. The radius of the first star is twice as large as the second star. What is the ratio of the temperature of the first star to the temperature of the second star?
The ratio of the temperature of the first star to the temperature of the second star is 4:1
In order to calculate the ratio of the temperature of the first star to the temperature of the second star, we need to use the Stefan-Boltzmann law.
What is the Stefan-Boltzmann law?
The Stefan-Boltzmann law states that the rate of radiation emitted by a black body is proportional to the fourth power of the body's absolute temperature.
What is the formula of Stefan-Boltzmann law?
The formula for Stefan-Boltzmann law is given as:
q = εσT^4
Where,
q = the energy radiated per unit area per unit time.
ε = Emissivity (In this case, it's 1).
σ = Stefan-Boltzmann constant = 5.67 × 10-8 W/m2.K4.
T = Temperature in Kelvin.
Now, let's proceed to solve the problem.
Given,
Emissivity of both stars (ε) = 1
Radius of the first star (r1) = 2r2 (i.e twice as large as the second star)
According to Stefan-Boltzmann law,
q1/q2 = (T1^4/T2^4)
We know that
q1 = q2 , because both the stars radiate thermal energy at the identical rate.
q1/q2 = 1
q1 = εσT1^4A1
q2 = εσT2^4A2
As the area of both stars is not given, we can assume it as same for both the stars.
q1 = q2εσT1^4
A = εσT2^4A
q1/q2
= T1^4/T2^4
= (r1/r2)^2q1/q2
= (r1/r2)^2
= (2r2/r2)^2
= 2^2
= 4
Therefore,
The ratio of the temperature of the first star to the temperature of the second star is 4:1
Answer: 4:1
Learn more about Stefan-Boltzmann law here
https://brainly.com/question/30763196
#SPJ11
Using the loop rule and deriving the differential equation for an LC circuit find the current (sign included) through the inductor at the instant t = 1.2 s if L = 2.7 H, C = 3.3 F. The initial charge at the capacitor is Qo = 4.30 and the initial current through the inductor is lo=0. Number Units
The current (sign included) through the inductor at the instant t is -0.089 A (negative sign implies that the current direction is opposite to the assumed direction).
How to determine current?The loop rule in an LC circuit gives us the equation Q/C + L×dI/dt = 0. Using the fact that I = dQ/dt, differentiate both sides to obtain:
d²Q/dt² + 1/(LC)Q = 0
This is a simple harmonic oscillator equation. The general solution is:
Q(t) = A cos(wt + φ)
where w = √(1/LC) is the angular frequency, A is the amplitude, and φ is the phase.
Given that Q(0) = Qo = 4.30, so:
A cos(φ) = Qo
Also given that I(0) = dQ/dt(0) = Io = 0. So differentiating Q(t) and setting t = 0 gives:
-Aw sin(φ) = Io
From these two equations solve for A and φ. The second equation tells us that sin(φ) = 0, so φ is 0 or pi. Since cos(0) = 1 and cos(pi) = -1, and A must be positive (since it's an amplitude), we choose φ = 0. This gives:
A = Qo
So the solution is:
Q(t) = Qo cos(wt)
and hence
I(t) = dQ/dt = -w Qo sin(wt)
Substitute w = √(1/LC), Qo = 4.30, and t = 1.2s:
I(1.2) = - √(1/(2.73.3)) × 4.3 × sin( √(1/(2.73.3)) × 1.2)
Doing the arithmetic, this gives:
I(1.2) = -0.089 A
The negative sign implies that the current direction is opposite to the assumed direction.
Find out more on loop rule here: https://brainly.com/question/30786490
#SPJ4
The period of a simple pendulum on the surface of Earth is 2.27 s. Determine its length L. E
The period of a simple pendulum on the surface of Earth is 2.27 s.The length of the simple pendulum is approximately 0.259 meters (m).
To determine the length of a simple pendulum, we can rearrange the formula for the period of a pendulum:
T = 2π × √(L / g)
where T is the period, L is the length of the pendulum, and g is the acceleration due to gravity.
Given that the period of the pendulum is 2.27 s and the acceleration due to gravity on the surface of Earth is approximately 9.81 m/s^2, we can substitute these values into the formula:
2.27 s = 2π ×√(L / 9.81 m/s^2)
Dividing both sides of the equation by 2π:
2.27 s / (2π) = √(L / 9.81 m/s^2)
Squaring both sides of the equation:
(2.27 s / (2π))^2 = L / 9.81 m/s^2
Simplifying:
L = (2.27 s / (2π))^2 × 9.81 m/s^2
Calculating the value:
L ≈ 0.259 m
The length of the simple pendulum is approximately 0.259 meters (m).
To learn more about period of a pendulum visit: https://brainly.com/question/26524032
#SPJ11
What does a triple-beam balance require the user to do?
O add the numbers from the three sliders to determine the mass of an object
O multiply the numbers from the three sliders to determine the mass of an object .
O add the numbers from the three sliders to determine the volume of an object. Omultiply the numbers from the three sliders to determine the volume of an object
Answer:
The correct option is:
O add the numbers from the three sliders to determine the mass of an object
An object that is 5 cm high is placed 70 cm in front of a concave (converging) mirror whose focal length is 20 cm. Determine the characteristics of the image: Type (real or virtual): Location: Magnification: Height:
The image formed by a concave mirror given the object's characteristics is real, inverted, and located 28 cm in front of the mirror.
The magnification is -0.4, implying the image is smaller than the object with a height of -2 cm. The mirror formula, 1/f = 1/v + 1/u, is used to find the image's location (v), where f is the focal length (20 cm) and u is the object's distance (-70 cm). Solving, we get v = -28 cm, meaning the image is 28 cm in front of the mirror. The negative sign indicates the image is real and inverted. To find the magnification (m), we use m = -v/u, getting m = 0.4, again a negative sign indicating an inverted image. Lastly, the height of the image (h') can be found by multiplying the magnification by the object's height (h), giving h' = m*h = -0.4*5 = -2 cm.
Learn more about concave mirrors here:
https://brainly.com/question/33230444
#SPJ11
Prove the effective thickness equation.
To prove the effective thickness equation, we need to start with the basic equation for thermal resistance in a composite wall. The thermal resistance of a composite wall can be expressed as:
1/[tex]R_{total[/tex] = Σ[tex](L_i / k_i)[/tex],
where [tex]R_{total[/tex] is the total thermal resistance, [tex]L_i[/tex] is the thickness of each layer i, and [tex]k_i[/tex] is the thermal conductivity of each layer i.
Now, let's consider a composite wall consisting of multiple layers with varying thicknesses. The effective thickness ([tex]L_{eff[/tex]) is defined as the thickness of a single imaginary layer that would have the same thermal resistance as the composite wall. We want to derive an equation for [tex]L_{eff[/tex].
To begin, we can rewrite the thermal resistance equation for the composite wall as:
1/[tex]R_{total[/tex] = ([tex]L_1 / k_1) + (L_2 / k_2) + ... + (L_n / k_n)[/tex],
where n is the total number of layers in the composite wall.
Now, we introduce the concept of effective thermal conductivity ([tex]k_{eff)[/tex], which is the thermal conductivity that the composite wall would have if it were replaced by a single imaginary layer with thickness [tex]L_{eff[/tex]. We can express this as:
[tex]k_{eff[/tex] = Σ[tex](L_i / k_i[/tex]).
The effective thermal conductivity represents the ratio of the total thickness of the composite wall to the total thermal resistance.
Next, we can rearrange the equation for the effective thermal conductivity to solve for[tex]L_{eff[/tex]:
[tex]k_{eff = L_{eff / R_{total.[/tex]
Now, we can substitute the expression for the total thermal resistance ([tex]R_{total[/tex]) from the thermal resistance equation:
[tex]k_{eff = L_{eff / ((L_1 / k_1) + (L_2 / k_2) + ... + (L_n / k_n)[/tex]).
Finally, by rearranging the equation, we can solve for [tex]L_{eff[/tex]:
[tex]L_eff = k_eff / ((1 / L_1) + (1 / L_2) + ... + (1 / L_n)).[/tex]
This is the effective thickness equation, which gives the thickness of a single imaginary layer that would have the same thermal resistance as the composite wall.
The effective thickness equation allows us to simplify the analysis of composite walls by replacing them with a single equivalent layer. This concept is particularly useful when dealing with heat transfer calculations in complex systems with multiple layers and varying thicknesses, as it simplifies the calculations and reduces the system to an equivalent homogeneous layer.
Learn more about resistance here:
https://brainly.com/question/14547003
#SPJ11
Paragraph Styles Question 4 A condenser is used to condense substances from gaseous to liquid state, typically by cooling it. In this problem, a stream of humid air (58.0 mol % water), 8.8 mol % O₂ and the remaining N₂ enters a condenser at 150°C. 80% of the water vapor in the humid air is condensed and removed as pure liquid water. Both gas and liquid phase streams leave the condenser at 30°C. Nitrogen (N₂) gas leave the condenser at the rate of 5.18 mol/s. (a) Draw and label a flowchart of the process. (4 marks) 1 (b) Solve the total flow rate of the feed stream and both streams leaving the condenser. (c) Taking [N₂ (g, 30°C), O2 (g, 30°C), and H₂O (g, 30°C)] as reference for enthalpy calculations, prepare and fill in the inlet-outlet enthalpy table and calculate the heat transferred to or from the condenser in kilowatts (Neglect the effects of pressure changes on enthalpies)
(a) Flowchart: A condenser process flowchart is provided, illustrating the inputs and outputs of the humid air stream, O₂, N₂, and the condensed liquid water. (b) Total flow rate: The total flow rate of the feed stream entering the condenser is 5.296F mol/s, considering the flow rates of water vapor, O₂, and N₂. (c) Enthalpy and heat transfer: The enthalpy changes for water vapor and O₂ are calculated, resulting in a heat transfer of -0.072 kF kW, indicating heat removal by the condenser. the heat transferred by the condenser is -0.072 kF kW.
(a) Flowchart:
(b) Total flow rate of the feed stream:
The flow rate of N2 leaving the condenser is given as 5.18 mol/s.
The flow rate of water vapor entering the condenser is 58.0 mol% of F.
80% of the above water vapor is condensed and removed, leaving 20% remaining.
So, 20% of the above water vapor remaining in the humid air after condensation is 0.116F mol/s.
The flow rate of O2 is given as 8.8 mol% of F.
The total flow rate of the feed stream is the sum of the flow rates of water vapor, O2, and N2:
Total flow rate = Flow rate of water vapor + Flow rate of O2 + Flow rate of N2
= 0.116F + 0.088F + 5.18
= 5.296F mol/s
(c) Inlet-Outlet Enthalpy Table:
To calculate the heat transferred by the condenser, we need to determine the enthalpy changes for water vapor (H3 to H4) and O2 (H5).
The enthalpy change for water vapor can be calculated as:
ΔH_vap = Enthalpy of water vapor at 30°C - Enthalpy of water vapor at 150°C
= [40.657 + 0.119 × (30 - 0)] - [40.657 + 0.119 × (150 - 0)]
= -13.607 kJ/kmol
Enthalpy of water leaving the condenser (H4) can be calculated as:
H4 = Enthalpy of water vapor at 30°C = 40.657 kJ/kmol
Enthalpy of O2 leaving the condenser (H5) can be taken as:
H5 = Enthalpy of O2 at 30°C = 0.102 kJ/kmol
The heat transferred by the condenser (q) can be calculated as:
q = Total flow rate × ΔH
= (5.296F mol/s) × (-13.607 kJ/kmol) × 10⁻³ kW/J
= -0.072 kF kW (where kF is the constant conversion factor 10⁶)
Therefore, the heat transferred by the condenser is -0.072 kF kW.
To know more about condenser click here:
https://brainly.com/question/13853336
#SPJ11
Consider to boil a 1 litre of water (25ºC) to vaporize within 10 min using concentrated sunlight.
Calculate the required minimum size of concentrating mirror.
Here, the specific heat is 4.19 kJ/kg∙K and the latent heat of water is 2264.71 kJ/kg.
Solar energy density is constant to be 1 kWm-2.
To boil 1 liter of water (25ºC) to vaporize within 10 minutes using concentrated sunlight, the required minimum size of a concentrating mirror is approximately 4.3 square meters.
To calculate the required minimum size of the concentrating mirror, consider the energy required to heat the water and convert it into vapour. The specific heat of water is 4.19 kJ/kg.K, which means it takes 4.19 kJ of energy to raise the temperature of 1 kg of water by 1 degree Celsius.
The latent heat of water is 2264.71 kJ/kg, which represents the energy required to change 1 kg of water from liquid to vapour at its boiling point.
First, determine the mass of 1 litre of water. Since the density of water is 1 kg/litre, the mass will be 1 kg. To raise the temperature of this water from [tex]25^0C[/tex] to its boiling point, which is [tex]100^0C[/tex],
calculate the energy required using the specific heat formula:
Energy = mass × specific heat × temperature difference
[tex]1 kg * 4.19 kJ/kg.K * (100^0C - 25^0C)\\= 1 kg * 4.19 kJ/kg.K * 75^0C\\= 313.875 kJ[/tex]
To convert this water into vapour, calculate the energy required using the latent heat formula:
Energy = mass × latent heat
= 1 kg × 2264.71 kJ/kg
= 2264.71 kJ
The total energy required is the sum of the energy for heating and vaporization:
Total energy = 313.875 kJ + 2264.71 kJ
= 2578.585 kJ
Now, determine the time available to supply this energy. 10 minutes, which is equal to 600 seconds. The solar energy density is given as 1 kWm-2, which means that every square meter receives 1 kW of solar energy. Multiplying this by the available time gives us the total energy available:
Total available energy = solar energy density * time
= [tex]1 kW/m^2 * 600 s[/tex]
= 600 kWs
= 600 kJ
To find the minimum size of the concentrating mirror, we divide the total energy required by the total available energy:
Minimum mirror size = total energy required / total available energy
= 2578.585 kJ / 600 kJ
= [tex]4.3 m^2[/tex]
Therefore, approximately 4.3 square meters for the concentrating mirror is required.
Learn more about concentrating mirror here:
https://brainly.com/question/31588513
#SPJ11
Commercial airplanes are sometimes pushed out of the passenger loading area by a tractor. (a) An 1800-kg tractor exerts a force of 2.38e4 N backward on the pavement, and the system experiences opposing friction forces that total 2400 N. If the acceleration is 0.150 m/s² , what is the mass of the airplane? (b) Calculate the force exerted by the tractor on the airplane, assuming 2200 N of the friction is experienced by the airplane.
(a) Mass of the airplane, Therefore, the mass of the airplane is 1.47 × 10⁵ kg. (b)Force exerted by the tractor on the airplane. Therefore, the force exerted by the tractor on the airplane is 2.59 × 10⁴ N.
(a)Mass of the airplane the free-body diagram (FBD) is shown below:
The sum of the forces in the horizontal direction is given by:
ΣFx = maxFtrac - Ff = max
Rearranging the above equation in terms of the mass of the airplane, m, gives:m = (Ftrac - Ff) / a
Substituting the given values, Ftrac = 2.38 × 10⁴ N, Ff = 2400 N, and a = 0.150 m/s²m = (2.38 × 10⁴ - 2400) / 0.150m = 1.47 × 10⁵ kg
Therefore, the mass of the airplane is 1.47 × 10⁵ kg.
(b)Force exerted by the tractor on the airplane
The free-body diagram (FBD) is shown below:The sum of the forces in the horizontal direction is given by:
ΣFx = maxFtrac - Ff - Fplane = max
where Fplane is the force exerted by the airplane on the tractor. Since the airplane is being pushed backwards by the tractor, the force exerted by the airplane on the tractor is in the forward direction.
Substituting the given values,Ftrac = 2.38 × 10⁴ N, Ff = 2400 N, a = 0.150 m/s², and Ff(plane) = 2200 N,m = 1.47 × 10⁵ kg
Thus,2.38 × 10⁴ - 2400 - 2200 = (1.47 × 10⁵) × 0.150 × FplaneFplane = 2.59 × 10⁴ N
Therefore, the force exerted by the tractor on the airplane is 2.59 × 10⁴ N.
Learn more about free-body diagram here:
https://brainly.com/question/30306775
#SPJ11
A rescue helicopter lifts a 75.3−kg person straight up by means of a cable. The person has an upward acceleration of 0.602 m/s 2
and is lifted from rest through a distance of 12.2 m. Use the work-energy theorem and find the final speed of the person. (Take up positive and down negative) 3.98 m/s 3.28 m/s 5.48 m/s 5.21 m/s 4.51 m/s A 7.05-kg monkey is hanging by one arm from a branch and swinging on a vertical circle. As an approximation, assume a radial distance of 62.1 cm is between the branch and the point where the monkey's mass is located. As the monkey swings through the lowest point on the circle, it has a speed of 3.38 m/s. Find the magnitude of the tension in the monkey's arm. 145.58 N 124.56 N 198.78 N 218.12 N
The magnitude of the tension in the monkey's arm is 218.12 N. Answer: 218.12 N.
Part AThe weight of the person is the force with which the person is acted upon by gravity. Therefore, the work done by the gravitational force on the person is given by Wg = mghWhere m = 75.3 kg, g = 9.81 m/s², and h = 12.2 mTherefore, Wg = (75.3 kg)(9.81 m/s²)(12.2 m) = 8905.89 JAlso, the work done by the helicopter is given by Wh = (1/2)mv² - (1/2)mu²Where v = final velocity, u = initial velocity, and Wh is the work done by the helicopter on the person since it lifts the person upwards through a distance of 12.2 m.
To obtain the final velocity of the person, we equate Wg to Wh since the net work done on the person is zero. Thus,8905.89 J = (1/2)(75.3 kg)v² - (1/2)(75.3 kg)(0 m/s)²8905.89 J = (1/2)(75.3 kg)v²v² = (2 × 8905.89 J)/(75.3 kg)v² = 236.66v = sqrt(236.66) = 15.38 m/sPart BWhen the monkey is at the lowest point of the circle, the only forces acting on the monkey are the gravitational force and the tension in the arm. The gravitational force acts downwards while the tension in the arm acts upwards.
Therefore, the net force acting on the monkey is the difference between the tension and the gravitational force. This net force causes the monkey to move in a circle of radius 62.1 cm. Thus, the magnitude of the net force can be obtained using the centripetal force equation;Fc = mv²/RFc = (7.05 kg)(3.38 m/s)²/(0.621 m)Fc = 139.28 NSince the net force is the difference between the tension and the gravitational force, we haveT - mg = Fcwhere T is the tension and m is the mass of the monkey.
Therefore, the magnitude of the tension in the monkey's arm can be obtained as;T = Fc + mgT = 139.28 N + (7.05 kg)(9.81 m/s²)T = 218.12 NTherefore, the magnitude of the tension in the monkey's arm is 218.12 N. Answer: 218.12 N.
Learn more about magnitude here,
https://brainly.com/question/30337362
#SPJ11
A bead with a hole through it slides on a wire track. The wire is threaded through the hole in the bead, and the bead slides without friction around a loop-the-loop (see figure below). The bead is released from rest at a height h = 3.60R.
(a) What is its speed at point A? (Use the following as necessary: the acceleration due to gravity g, and R.)
V =
(b) How large is the normal force on the bead at point A if its mass is 5.50 grams?
magnitude __________N
(c) What If? What is the minimum height h from which the bead can be released if it is to make it around the loop? (Use any variable or symbol stated above as necessary.)
h = ______
(a) The speed of the bead at point A is 6.47 m/s.
(b) The normal force on the bead at point A is 2.49 N
(c) The minimum height h from which the bead can be released is 5R/2.
(a)
Use the conservation of energy principle.
The initial energy, when the bead is released from rest at a height h = 3.60R, is entirely due to its potential energy.
The final energy of the bead at point A is entirely due to its kinetic energy, since it is sliding without friction around the loop-the-loop.
Let M be the mass of the bead and v be its velocity at point A, then we have:
Mgh = 1/2MV² + MgR
where g is the acceleration due to gravity, and h = 3.60R is the height from which the bead is released.
Simplifying and solving for v gives:
v = sqrt(2gh - 2gR)
where sqrt() stands for square root.
Substituting the values of g and R gives:
v = sqrt(2*9.81*3.6 - 2*9.81*1)
v = 6.47 m/s
Therefore, the speed of the bead at point A is 6.47 m/s.
(b)
To find the normal force on the bead at point A, we need to consider the forces acting on the bead at this point.
The normal force is the force exerted by the wire on the bead perpendicular to the wire. It balances the force of gravity on the bead.
At point A, the forces acting on the bead are the force of gravity acting downwards and the normal force acting upwards.
Since the bead is moving in a circular path, it is accelerating towards the center of the loop.
Therefore, there must be a net force acting on it towards the center of the loop.
This net force is provided by the component of the normal force in the direction towards the center of the loop.
This component is given by:
Ncosθ = MV²/R
where θ is the angle between the wire and the vertical, and N is the normal force.
Substituting the values of M, V, and R gives:
Ncosθ = 5.50*10⁻³*(6.47)²/1
Ncosθ = 2.49
Therefore, the normal force on the bead at point A is 2.49 N.
(c)
The bead will lose contact with the wire at the top of the loop when the normal force becomes zero.
This occurs when the component of the force of gravity acting along the wire becomes equal to the centripetal force required to keep the bead moving in a circular path.
The component of the force of gravity along the wire is given by:
Mg sinθ = MV²/R
where θ is the angle between the wire and the vertical, and Mg is the force of gravity acting downwards.
Substituting the values of M, V, and R gives:
Mg sinθ = 5.50*10⁻³*(6.47)²/1
Mg sinθ = 0.789
Since sinθ can never be greater than 1, we have:
Mg sinθ ≤ Mg
The minimum height h from which the bead can be released is obtained by equating the potential energy of the bead at this height to the kinetic energy required to keep the bead moving in a circular path at the top of the loop.
This gives:
Mgh = 1/2MV² + MgR
Substituting V² = gR and simplifying gives:
h = 5R/2
Therefore, the minimum height h from which the bead can be released is 5R/2.
Learn more about the normal force:
brainly.com/question/29458258
#SPJ11
The force of attraction that a 37.5 μC point charge exerts on a 115 μC point charge has magnitude 3.05 N. How far apart are these two charges?
The force of attraction that a 37.5 μC point charge exerts on a 115 μC point charge has magnitude 3.05 NThe two charges, 37.5 μC and 115 μC, are attracted to each other with a force of magnitude 3.05 N.
Coulomb's law states that the force of attraction or repulsion between two charges is directly proportional to the product of the charges and inversely proportional to the square of the distance between them. Mathematically, it can be expressed as:
F = k * (|q1| * |q2|) / r^2
where F is the force of attraction or repulsion, k is the electrostatic constant (k = 8.99 × 10^9 N m^2/C^2), q1 and q2 are the charges, and r is the distance between the charges.
In this case, we have a force of 3.05 N, a charge of 37.5 μC (3.75 × 10^-5 C), and a charge of 115 μC (1.15 × 10^-4 C). We need to find the distance (r) between the charges.
Using Coulomb's law, we can rearrange the formula to solve for the distance:
r = √(k * (|q1| * |q2|) / F)
Substituting the given values:
r = √((8.99 × 10^9 N m^2/C^2) * ((3.75 × 10^-5 C) * (1.15 × 10^-4 C)) / (3.05 N))
Simplifying the expression:
r = √(39.18 m^2)
r ≈ 6.26 m
Therefore, the two charges are approximately 6.26 meters apart.
Learn more about magnitude here:
https://brainly.com/question/31022175
#SPJ11