The expected amount of gasoline to be floating on the water table surface would be 1,000 liters (a whole number with no decimals or commas), the correct answer is 1000.
Given:A 50,000 liter above ground gasoline storage tank (UST) has leaked its entire contents which penetrated into the surrounding subsurface.
Contaminant hydrogeologists confirmed that a soil region in the vadose zone of 20 cubic meters held gasoline in its pore spaces due to capillary forces.The groundwater table occurs several meters below the bottom of the affected vadose zone.
To Find: How much gasoline would you expect to be floating on the water table surface?Based on the 5% rule:This means that only 5% of the gasoline spilled from the tank will end up floating on the water table surface.
Thus, the amount of gasoline that would be expected to be floating on the water table surface would be 5% of the total amount of gasoline that was originally in the vadose zone.
Therefore,Total amount of gasoline in the vadose zone = 20 cubic metersSince 1 m³ = 1000 liters. Therefore, volume of gasoline in the vadose zone = 20 m³ × 1000 liters/m³= 20,000 liters
Since the entire contents of the storage tank were spilled, this is the total amount of gasoline that was originally in the vadose zone.
So,The amount of gasoline floating on the water table surface = 5% of the total amount of gasoline= 5/100 × 20,000= 1,000.
To know more about gasoline visit :
https://brainly.com/question/33360773
#SPJ11
A bacterial culture in a petri dish grows at an exponential rate. The petri dish has an area of 256 mm2, and the bacterial culture stops growing when it covers this area. The area in mm2 that the bacteria cover each day is given by the function ƒ(x) = 2x. What is a reasonable domain for this function? A. Begin inequality . . . 0 is less than x which is less than or equal to 256 . . . end inequality B. Begin inequality . . . 0 is less than x which is less than or equal to 128 . . . end inequality C. Begin inequality . . . 0 is less than x which is less than or equal to the square root of 256 . . . end inequality D. Begin inequality . . . 0 is less than x which is less than or equal to 8 . . . end inequality
The correct answer is: A. Begin inequality . . . 0 < x ≤ 256 . . . end inequality
To determine a reasonable domain for the function ƒ(x) = 2x, we need to consider the context of the problem.
The function represents the area in mm2 that the bacterial culture covers each day. The maximum area that the bacteria can cover is 256 mm2, as stated in the problem.
Since the function represents the area covered each day, it wouldn't make sense to have a negative number of days (x) or to have more than 256 days (x) since that would exceed the maximum area.
Therefore, a reasonable domain for this function would be a range of days starting from 0 (the initial day) up to and including the day when the bacterial culture fully covers the petri dish, which is 256 mm2.
The correct answer is:
A. Begin inequality . . . 0 < x ≤ 256 . . . end inequality
Learn more about inequality from
https://brainly.com/question/25944814
#SPJ11
Let L = {w € {a + b}" | #b(w) is even}. Which one of the regular expression below represents L? pt) (a) (a*ba*b)* (b) a*(baba")" (c) a* (ba*b*)*a* (d) a*b(ba*b)"ba
The regular expression that represents the language L is option (c) a* (bab)a. This regular expression matches strings that consist of zero or more 'a's followed by zero or more occurrences of the pattern 'bab', and ending with zero or more 'a's. This pattern ensures that the number of 'b's in the string is always even.
To understand why option (c) is the correct regular expression for representing the language L, let's break down the components of the regular expression:
a* - Matches zero or more occurrences of 'a'.
(bab)* - Matches zero or more occurrences of the pattern 'bab', where 'b' can be followed by zero or more 'a's. This pattern allows for an arbitrary number of 'b's to occur, as long as the count is even.
a* - Matches zero or more occurrences of 'a'.
By combining these components, the regular expression ensures that any string in L will start and end with zero or more 'a's and have an even number of 'b's in between.
The other options (a), (b), and (d) do not correctly represent the language L. Option (a) allows for any number of 'b's, including odd counts.
Option (b) requires a specific pattern of 'baba' to appear in the string, which may not satisfy the condition of having an even number of 'b's. Option (d) allows for an arbitrary number of 'b's without enforcing an even count.
Therefore, option (c) is the correct choice for representing the language L.
To learn more about even number visit:
brainly.com/question/2263644
#SPJ11
what is the perimeter of the pentagon?
Please answer my question quickly!
[tex]12^6[/tex], ? = 6
Step-by-step explanation:We are given instructions by the problem. When dividing exponential expressions with the same base, we can find the difference (subtraction) between the exponents and keep the base.
[tex]\displaystyle 12^9 \div 12^3=12^{9-3}=12^6[/tex]
But why does this work?Let us write it out.
[tex]\displaystyle 12^9 \div 12^3 = \frac{12^9}{12^3} =\frac{12*12*12*12*12*12*12*12*12}{12*12*12}[/tex]
Now, 12 divided by 12 (aka [tex]\frac{12}{12}[/tex]) is equal to 1.
[tex]\displaystyle 1*1*1*12*12*12*12*12*12}[/tex]
And anything times one is itself. Then, we can rewrite this as 12 to the power of 6 because we are multiplying 12 by itself 6 times.
[tex]\displaystyle 12*12*12*12*12*12} =12^6[/tex]
If the probability of a tornado today is 1/10 , would you say that there will likely be a tornado today?
Answer:
10% chance if the probability is 1/10
Let M={(a,a):a<−2}∈R^2. Then M is a vector space under standard addition and scalar multiplication in R^2. False True
Let M={(a,a):a<−2}∈R². Then M is a vector space under standard addition and scalar multiplication in R² is False
The set M={(a,a):a<−2}∈R² is not a vector space under standard addition and scalar multiplication in R².
In order for a set to be considered a vector space, it must satisfy several properties, including closure under addition and scalar multiplication, as well as the existence of zero vector and additive inverses. Let's examine these properties in relation to the given set M={(a,a):a<−2}∈R².
Firstly, closure under addition means that if we take any two vectors from M and add them together, the result should also be in M. However, if we consider two vectors (a, a) and (b, b) from M, their sum would be (a + b, a + b).
Since a and b can be any real numbers less than -2, it is possible to choose values that violate the condition for M. For example, if a = -3 and b = -4, the sum would be (-7, -7), which does not satisfy the condition a < -2. Therefore, M is not closed under addition.
Secondly, in order to be a vector space, M should also be closed under scalar multiplication. This means that if we multiply a vector from M by a scalar, the resulting vector should still be in M. However, if we take a vector (a, a) from M and multiply it by a scalar k, the result would be (ka, ka).
Again, by choosing a value of a less than -2, we can find values of k that violate the condition for M. For instance, if a = -3 and k = -1/2, the scalar product would be (3/2, 3/2), which does not satisfy the condition a < -2. Hence, M fails to be closed under scalar multiplication.
Moreover, M does not contain the zero vector (0, 0), which is required for a vector space. Additionally, it does not contain additive inverses for all its elements. If we consider the vector (a, a) from M, its additive inverse would be (-a, -a). However, since a is restricted to be less than -2, there are values of a that do not have additive inverses within the set M.
In conclusion, the set M={(a,a):a<−2}∈R² does not satisfy the necessary conditions to be a vector space under standard addition and scalar multiplication in R². It fails to exhibit closure under addition and scalar multiplication, and it lacks the zero vector and additive inverses for all its elements.
Learn more about vector space
brainly.com/question/29991713
#SPJ11
Rank the following facility layouts in an increasing order of product variety (A) Project layout (B) Cellular layout (C) Job shop (D) Flow shop
In facility layout design, different layout types are utilized depending on the nature of the production system and the product variety.
Ranking in increasing order of product variety:
1) Project layout (lowest product variety)
2) Flow shop
3) Cellular layout
4) Job shop (highest product variety)
1) Project layout: This layout is typically used for large-scale projects where each project is unique and requires specialized equipment and resources. The product variety is generally low as each project is distinct and tailored to specific requirements.
2) Flow shop: A flow shop layout follows a linear production path, with a series of operations performed in a predetermined sequence. It is suitable for mass production of standardized products with a limited range of variations, resulting in a moderate level of product variety compared to the other layouts.
3) Cellular layout: Cellular layout involves grouping machines and equipment into cells based on product families or process requirements. It allows for greater flexibility and customization, resulting in a higher product variety compared to flow shop and project layouts.
4) Job shop: Job shop layout is characterized by the organization of work centers based on similar processes. It accommodates a wide range of product variety and customization, as each job or order may require unique operations and processes.
The ranking of facility layouts in terms of product variety is based on the level of customization and flexibility they offer. Project layout, with its focus on unique projects, has the lowest product variety. Flow shop offers a moderate level of variety suitable for standardized products. Cellular layout provides greater customization and flexibility, resulting in a higher product variety.
Job shop layout, accommodating a wide range of processes and operations, offers the highest product variety among the given facility layouts. Understanding the characteristics and strengths of each layout type is crucial in selecting the appropriate layout for a particular production system and product requirements.
Learn more about layout design visit:
https://brainly.com/question/23448677
#SPJ11
With A Total Heat Capacity Of 5.86 KJ/°C. The Temperature Of The Calorimeter Increases From 23.5°C To 39.8°C. What Would Be The Heat Of Combustion Of C6H12 In KJ/Mol
A 4.25 g sample of C6H12 is burned in a bomb calorimeter with a total heat capacity of 5.86 kJ/°C. The temperature of the calorimeter increases from 23.5°C to 39.8°C. What would be the heat of combustion of C6H12 in kJ/mol
With the heat of combustion of C6H12 determined to be 85.4 kJ/mol based on the given data and calculations, this exothermic reaction releases a significant amount of energy when one mole of C6H12 is completely burned in excess oxygen.
This information is crucial for understanding the fuel efficiency and energy potential of C6H12, making it a valuable component in various industrial processes and a potential candidate for clean and sustainable energy solutions.
Given data:
Mass of C6H12 = 4.25 g
ΔT = Change in temperature = 39.8°C - 23.5°C = 16.3°C = 16.3 K
Heat capacity of calorimeter = 5.86 kJ/°C
Heat of combustion of C6H12 = ?
Heat of combustion of C6H12 can be calculated using the formula:
Heat released = Heat absorbed
q = m × s × ΔT
where
q = Heat released or absorbed
m = mass of substance (in grams)
s = Specific heat capacity (in J/g°C or J/mol°C)
ΔT = Change in temperature (in °C or K)
For one mole of C6H12, the heat of combustion can be calculated as:
1 mol of C6H12 = 6 × 12.01 g/mol + 12 × 1.01 g/mol = 84.18 g/mol
Heat released by C6H12 = Heat absorbed by the calorimeter
Q = (mass of calorimeter + water) × heat capacity × ΔT
According to the law of conservation of energy, heat released = heat absorbed
Q = Heat released by C6H12 = Heat absorbed by the calorimeter
Let's substitute the given values in the equation:
4.25 g of C6H12 produces ΔT = 16.3 K heat in the calorimeter.
Q = (mass of calorimeter + water) × heat capacity × ΔT
4.25 g of C6H12 produces ΔT = 16.3 K heat in the calorimeter.
(100 g of water = 100 mL of water = 0.1 L of water = 0.1 kg of water)
Mass of calorimeter + water = 100 + 5.86 = 105.86 g = 0.10586 kg
Q = 0.10586 kg × 5.86 kJ/°C × 16.3 K = 10.68 kJ
Heat of combustion of C6H12 = q/moles of C6H12
= 10.68 kJ/0.125 mol = 85.4 kJ/mol
Therefore, the heat of combustion of C6H12 is 85.4 kJ/mol.
Learn more about heat of combustion
https://brainly.com/question/30794605
#SPJ11
What are the domain and range of the function?
Answer:
Domain: {0, 1, 2, 3)
Range: {4, 5, 6.25, 7.8125}
Step-by-step explanation:
Domain is the x value going right or left.
Range is the y value going up or down.
Horizontal line = --------
Vertical line = I
Design of STRUCTURES - AutoCAD - BS 8110
Design and draw a cantilever
beam
effective span = 4m
width of beam = 230mm and depth = 580
Imposed load = 4.0kN/m
Dead load = 1.2kN/m
Fcu = 30N/mm2
Fy = 500N/
We design and draw a cantilever beam in AutoCAD using BS 8110.
To design and draw a cantilever beam in AutoCAD using BS 8110, follow these steps:
1. Determine the required dimensions:
- Effective span: 4m
- Width of the beam: 230mm
- Depth of the beam: 580mm
2. Calculate the imposed load and dead load:
- Imposed load: 4.0kN/m
- Dead load: 1.2kN/m
3. Determine the concrete strength:
- Fcu (compressive strength): 30N/mm2
4. Determine the steel strength:
- Fy (yield strength): 500N/mm2
5. Calculate the maximum moment at the fixed end:
- Use the formula M = wL^2/2, where w is the total load per meter (imposed load + dead load) and L is the span length.
6. Determine the reinforcement:
- Calculate the area of steel required using the formula As = (0.87fy(M/Fcu))0.5, where As is the area of steel, fy is the yield strength, M is the maximum moment, and Fcu is the compressive strength.
- Choose an appropriate steel bar size based on the calculated area.
7. Design the beam:
- Draw the cantilever beam in AutoCAD with the given dimensions.
- Add the reinforcement bars at the bottom of the beam as per the calculated area and bar size.
- Ensure proper spacing and cover requirements as per the design standards.
Remember to refer to the BS 8110 code and consult with a structural engineer for accurate and safe design.
Learn more about the cantilever beam from the given link-
https://brainly.com/question/27910839
#SPJ11
Help me out you guysss thanksss
Write, without proof, the equations, together with boundary conditions, that describe a steady state (reactor) model for fixed bed catalytic reactor(FBCR) and that allow for the following axial convective flow of mass and energy, radial dispersion/conduction of mass and energy, cehemical reaction( A→ products) and energy transfer between reactor and surrounding. Write the equations in terms of CA and T. Define the meaning of each symbol used.
The equations and boundary conditions that describe a steady state (reactor) model for a fixed bed catalytic reactor (FBCR) that allows for the following axial convective flow of mass and energy, radial dispersion/conduction of mass and energy.
Chemical reaction (A → products), and energy transfer between the reactor and the surrounding are:
[tex]$$\frac{\partial C_a}{\partial t} = D_e\frac{\partial ^2 C_a}{\partial z^2} - \frac{u}{\epsilon} \frac{\partial C_a}{\partial z} - kC_a^m$$$$\frac{\partial T}{\partial t} = \frac{\alpha}{\rho C_p} \frac{\partial ^2 T}{\partial z^2} - \frac{u}{\epsilon} \frac{\partial T}{\partial z} + \frac{-\Delta H_r}{\rho C_p}kC_a^m$$.[/tex]
The meaning of each symbol used are as follows:
D_e - Effective diffusivity (m^2/s)u - Axial velocity (m/s)k - Rate constant (m/s)C_a - Concentration of A (mol/m^3)T - Temperature (K)z - Axial position (m)m - Reaction order in Aα - Thermal diffusivity (m^2/s)ρ - Density (kg/m^3)C_p - Specific heat capacity (J/kg.K)ΔH_r - Heat of reaction (J/mol)ε - Void fraction (unitless)Boundary conditions:
[tex]At z = 0, $$\frac{\partial C_a}{\partial z} = 0$$$$\frac{\partial T}{\partial z} = 0$$At z = L, $$C_a = C_{a,feed}$$$$T = T_{in}$$.[/tex]
These are the equations and boundary conditions that describe a steady state (reactor) model for fixed bed catalytic reactor (FBCR) and allow for the following axial convective flow of mass and energy, radial dispersion/conduction of mass and energy, a chemical reaction (A → products), and energy transfer between reactor and surrounding.
To know more about the Chemical reaction :
brainly.com/question/22817140
#SPJ11
The sales of Product X, Product Y, and Product Z, are in the ratio of 9:4:7, respectively. The sales of product Y in the next month are forecast to be $16,000. What will be the sales of Product X and Product Z in the next month if the sales of all the products are to maintain the same ratio? Select one: a. Product X = $9,000 and Product Z= $7,000 Ob. Product X = $36,000 and Product Z= $28,000 c. Product X = $30,500 and Product Z= $22,500 d. Product X = $18,000 and Product Z= $14,000
The sales of Product X in the next month will be $18,000, and the sales of Product Z will be $14,000.
To maintain the same ratio, we need to determine the sales of Product X and Product Z based on the given ratio and the forecasted sales of Product Y.
Let's assume that the sales of Product X, Product Y, and Product Z are 9x, 4x, and 7x, respectively, where x represents a common multiplier.
Given that the sales of Product Y in the next month are forecasted to be $16,000, we can set up the following equation:
4x = $16,000
Solving for x, we find that x = $4,000.
Now, we can calculate the sales of Product X and Product Z by multiplying their respective ratios by x:
Product X = 9x = 9 * $4,000 = $36,000
Product Z = 7x = 7 * $4,000 = $28,000
Therefore, the sales of Product X in the next month will be $36,000, and the sales of Product Z will be $28,000.
For more questions like Product click the link below:
https://brainly.com/question/33332462
#SPJ11
In Darcy's law, the average linear velocity of water is directly proportional to A. effective porosity B. specific discharge C. flow
In Darcy's law, the average linear velocity of water is directly proportional to (B) specific discharge.
This is because Darcy’s law defines the relationship between the rate of flow of a fluid through a porous material, the viscosity of the fluid, the effective porosity of the material and the pressure gradient. Specific discharge refers to the volume of water that flows through a given cross-sectional area of the aquifer per unit of time per unit width.
Darcy's law is used to determine the flow of fluids through permeable materials such as porous rocks. This law assumes that the flow of fluids is proportional to the pressure gradient and the properties of the permeable material. The specific discharge is the volume of fluid that passes through a unit width of the aquifer per unit time. Effective porosity is the ratio of the volume of void space to the total volume of the porous material.
The equation for Darcy’s law is expressed as:
Q = KA (h2 - h1) / L
Where:
Q = flow rate
K = hydraulic conductivity
A = cross-sectional area of the sampleh1 and h2 = the hydraulic heads at the ends of the sample
L = the length of the sample.
The specific discharge is a crucial parameter in groundwater hydrology because it determines the rate at which groundwater moves through the aquifer. The effective porosity is also an important parameter because it determines the amount of water that can be stored in the pore spaces of the material. In conclusion, the average linear velocity of water is directly proportional to the specific discharge in Darcy's law.
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
For a certain mammal, researchers have determined that the mesiodistal crown length of deciduous mandibular first molars is related to the post conception age of the tooth as L(t) = - .015t² + 1.44t - 7.7, where L(t) is the crown length (in millimeters) of the molar t weeks after conception. Find the maximum length in mesiodistal crown of mandibular first molars during weeks 30 through 60. The maximum length is mm. (Round to three decimal places as needed.)
The maximum length of the mesiodistal crown of mandibular first molars during weeks 30 through 60 is mm (rounded to three decimal places).
The given function represents the relationship between the mesiodistal crown length (L) of deciduous mandibular first molars and the post-conception age of the tooth (t) in weeks. To find the maximum length within the specified range of 30 to 60 weeks, we need to determine the vertex of the quadratic function L(t) = -0.015t² + 1.44t - 7.7.
The vertex of a quadratic function is given by the formula t = -b / (2a), where a, b, and c are the coefficients of the quadratic equation in standard form (ax² + bx + c).
In this case, the coefficients are:
a = -0.015
b = 1.44
Using the formula, we can find the vertex:
t = -1.44 / (2 * -0.015) = 48
Therefore, the maximum length occurs at t = 48 weeks. To find the maximum length, we substitute this value into the function:
L(48) = -0.015(48)² + 1.44(48) - 7.7
Calculating the value, we find the maximum length in millimeters.
Therefore, the correct choice is: The maximum length is mm (rounded to three decimal places).
Learn more about functions: brainly.com/question/11624077
#SPJ11
The maximum length of the mesiodistal crown of mandibular first molars during weeks 30 through 60 is mm (rounded to three decimal places).
The given function represents the relationship between the mesiodistal crown length (L) of deciduous mandibular first molars and the post-conception age of the tooth (t) in weeks. To find the maximum length within the specified range of 30 to 60 weeks, we need to determine the vertex of the quadratic function L(t) = -0.015t² + 1.44t - 7.7.
The vertex of a quadratic function is given by the formula t = -b / (2a), where a, b, and c are the coefficients of the quadratic equation in standard form (ax² + bx + c).
In this case, the coefficients are:
a = -0.015
b = 1.44
Using the formula, we can find the vertex:
t = -1.44 / (2 * -0.015) = 48
Therefore, the maximum length occurs at t = 48 weeks. To find the maximum length, we substitute this value into the function:
L(48) = -0.015(48)² + 1.44(48) - 7.7
Calculating the value, we find the maximum length in millimeters.
Therefore, the correct choice is: The maximum length is mm (rounded to three decimal places).
Learn more about functions: brainly.com/question/11624077
#SPJ11
A river that feeds into a lake has elevated nitrate from agricultural runoff (0.8 mg-N/L). The river has a flow of 240 ft³/s. Additionally, a wastewater treatment plant discharges 12 MGD of effluent with 5 mg-N/L of nitrate into the river. Nitrate is taken up in the lake by bacteria at a rate of 1.92 d¹¹. The lake as a volume of 3,000,000 ft and can be considered to be completely mixed. A drinking water treatment plant downstream of the lake requires that river water at the intake has a maximum of 1 mg-N/L of nitrate. Another wastewater treatment plant will be added upstream of the lake and will discharge 8 MGD of flow. What should be the permit limit for nitrate in mg-N/L for that new plant, so that the drinking water quality is not compromised? 1ft-7.48 gal MGD = 106 gal/d
The permit limit for nitrate in mg-N/L for the new plant should be 4.18 mg-N/L.
Given, River flow rate = 240 ft³/s
Nitrate level due to agricultural runoff = 0.8 mg-N/L
Discharge from wastewater treatment plant = 12 MGD
Nitrate level in the discharge from wastewater treatment plant = 5 mg-N/L
Nitrate uptake rate by bacteria = 1.92 d¹¹
Lake volume = 3,000,000 ft³
Permissible nitrate level at drinking water treatment plant = 1 mg-N/L
Additional discharge from new wastewater treatment plant = 8 MGD
To calculate the maximum permissible nitrate limit for the new wastewater treatment plant so that drinking water quality is not compromised,
we need to first calculate the nitrate level at the intake of the drinking water treatment plant.
It can be calculated as follows:
Let the nitrate level in the river after mixing be N.
Then, Total nitrate inflow rate = Nitrate outflow rate
240 x N + 12 x 106 x 5 = 3,000,000 x 1.92 d¹¹
Now,240 N + 12 x 106 x 5 = 3,000,000 x 1.92 d¹¹
240 N = 3,000,000 x 1.92 d¹¹ - 12 x 106 x 5N = (3,000,000 x 1.92 d¹¹ - 12 x 106 x 5) / 240N = 32.64 d⁻¹
The nitrate inflow rate from the new wastewater treatment plant will add an additional nitrogen inflow rate of 8 x 106 x Permit limit of nitrate from new treatment plant.
Then, Total nitrate inflow rate = Nitrate outflow rate
240 x N + 12 x 106 x 5 + 8 x 106 x Permit limit of nitrate from new treatment plant
= 3,000,000 x 1.92 d¹¹
Now,
240 N + 12 x 106 x 5 + 8 x 106 x Permit limit of nitrate from new treatment plant
= 3,000,000 x 1.92 d¹¹
240 N = 3,000,000 x 1.92 d¹¹ - 12 x 106 x 5 - 8 x 106 x Permit limit of nitrate from new treatment plant
N = (3,000,000 x 1.92 d¹¹ - 12 x 106 x 5 - 8 x 106 x Permit limit of nitrate from new treatment plant) / 240N
= 32.64 d⁻¹ - 8 x 106 x Permit limit of nitrate from new treatment plant / 240
Now, Nitrate level at the intake of drinking water treatment plant = 1 mg-N/L
Therefore,32.64 d⁻¹ - 8 x 106 x Permit limit of nitrate from new treatment plant / 240 = 1 mg-N/L
Permit limit of nitrate from new treatment plant = (32.64 d⁻¹ - 240) / 8 x 106
Permit limit of nitrate from new treatment plant = 4.18 mg-N/L
Hence, the permit limit for nitrate in mg-N/L for the new plant should be 4.18 mg-N/L.
To know more about Nitrate level visit:
https://brainly.com/question/32373608
#SPJ11
2A. Predict the change in entropy for the following: i) Carbon dioxide sublimes ii) Hydroiodic acid and Sodium Hydroxide are neutralized iii) Neon gas is liquefied under pressure.
(i) Sublimation typically leads to an increase in entropy. (ii) Neutralization of acids and bases can result in either an increase or decrease in entropy. (iii) The liquefaction of a gas under pressure usually leads to a decrease in entropy.
The change in entropy can be predicted for the following scenarios:
i) When carbon dioxide sublimes, it changes from a solid to a gas phase directly without going through the liquid phase. This process is an example of sublimation. The change in entropy during sublimation is usually positive because the gas phase has more disorder than the solid phase. The molecules in the gas phase move more freely and have more possible arrangements, increasing the entropy.
ii) When hydroiodic acid and sodium hydroxide are neutralized, a chemical reaction occurs. This reaction involves the formation of water and the formation of a salt called sodium iodide. The change in entropy during this process can be positive or negative depending on the specific conditions and concentrations of the reactants. If the reactants and products have a similar degree of disorder, the change in entropy may be small. However, if there is a significant difference in disorder between the reactants and products, the change in entropy can be large. For example, if the reaction involves the formation of a gas, such as carbon dioxide, the change in entropy would be positive as gases have higher entropy than liquids or solids.
iii) When neon gas is liquefied under pressure, the gas molecules are compressed and forced closer together, resulting in the formation of a liquid. The change in entropy during this process is usually negative because the liquid phase has less disorder than the gas phase. The molecules in the liquid are more closely packed and have fewer possible arrangements, reducing the entropy.
Let us know more about entropy :
https://brainly.com/question/32167470.
#SPJ11
Which of the following combinations of formula and name is incorrect? a nitride ion = NO2 b.chlorite ion =ClO_2 c.perchlorate ion =ClO_4− d.cyanide ion = CN
The incorrect combination is option b: chlorite ion = ClO₂. The correct formula for the chlorite ion is ClO₂⁻, not ClO₂.
The incorrect combination of formula and name is option b: chlorite ion = ClO₂.
Let's go through the provided options to determine which one is incorrect:
a. Nitride ion = NO₂
This combination is incorrect.
The formula for the nitride ion is N³⁻, which consists of three electrons gained by nitrogen to achieve a stable 8-electron configuration.
The correct formula for the nitride ion should be N³⁻, not NO₂.
b. Chlorite ion = ClO₂
This combination is correct.
The chlorite ion, ClO₂⁻, is composed of one chlorine atom bonded to two oxygen atoms with a charge of -1.
The chlorite ion is commonly found in compounds such as sodium chlorite (NaClO₂).
c. Perchlorate ion = ClO₄⁻
This combination is correct.
The perchlorate ion, ClO₄⁻, consists of one chlorine atom bonded to four oxygen atoms with a charge of -1.
Perchlorate is a polyatomic ion commonly found in compounds such as potassium perchlorate (KClO₄).
d. Cyanide ion = CN⁻
This combination is correct.
The cyanide ion, CN⁻, consists of one carbon atom bonded to a nitrogen atom with a charge of -1.
Cyanide is known for its high toxicity and is often found in compounds such as sodium cyanide (NaCN).
For similar question on electron configuration.
https://brainly.com/question/30933074
#SPJ8
1. In the specific gravity and absorption experiment, the following measurements were taken of coarse aggregates: Weight of pan used to weigh SSD aggregates Weight of pan + SSD aggregates Weight of SSD aggregates in water Weight of pan used to weigh oven-dried aggregates Weight of pan + oven dried aggregates Calculate the following properties: a. Specific gravity b. SSD specific gravity c. Apparent specific gravity d. Absorption = 500 g = 2550 g = 1300 g = 510 g = 2545 g 2. After manually sieving 100 g of cement on the No. 200 sieve, the mass retained on the sieve was found to be 8 grams. Determine the fineness of the cement.
Specific gravity = ((Weight of pan + SSD aggregates) - Weight of pan used to weigh SSD aggregates) / (Weight of pan + SSD aggregates - weight of SSD aggregates in water)Substitute the given values:Specific gravity = (2550 g - 500 g) / (2550 g - 1300 g)= 2.58
Therefore, the fineness of the cement is 8%.
SSD specific gravity = ((Weight of pan + SSD aggregates) - Weight of pan used to weigh SSD aggregates) / ((Weight of pan + SSD aggregates - weight of SSD aggregates in water) - weight of pan used to weigh oven-dried aggregates)Substitute the given values: SSD specific gravity = (2550 g - 500 g) / (2550 g - 1300 g - 510 g)= 2.70 Apparent specific gravity = Weight of pan + oven-dried aggregates - weight of pan used to weigh oven-dried aggregates / weight of water displaced by SSD aggregates Substitute the given values:Apparent specific gravity = (2545 g - 510 g) / (1300 g)= 1.67
Absorption = SSD specific gravity - apparent specific gravity Substitute the given values: Absorption = 2.70 - 1.67= 1.03 The absorption of the given aggregates is 1.03.Fineness is the amount of cement particles that pass through the No. 200 sieve. To calculate the fineness of the cement, we can use the formula below:Fineness = (Mass of cement retained on No. 200 sieve / Mass of cement) x 100 Given that the mass retained on the sieve is 8 g and the original mass of the cement is 100 g, we can substitute the values in the above formula: Fineness = (8 g / 100 g) x 100= 8%
To know more about gravity visit:
https://brainly.com/question/31321801
#SPJ11
How much heat must be supplied to 100 kg of water at 30°C to
make steam at 750 kPa that is 67% dry?
The amount of heat that must be supplied to 100 kg of water at 30°C to make steam at 750 kPa that is 67% dry is 775528.4 kJ.
To determine the amount of heat that should be supplied to 100 kg of water at 30°C to make steam at 750 kPa that is 67% dry, we can use the formula;
Q = mL, where
Q = amount of heat supplied
m = mass of water
L = latent heat of vaporization.
The mass of water that has to be heated is 100 kg. 67% of this is dry, so the mass of steam formed is;
Mass of dry steam = 0.67 × 100 = 67 kg
The mass of steam at saturation point at 750 kPa is given by;
Specific volume of steam at 750 kPa = 0.194 m3/kg
Mass of steam = volume / specific volume= 67 / 0.194
= 345.36 kg
The mass of steam that comes from the water is, Mass of water that gives rise to 1 kg of steam = 1 / 0.67
= 1.4925 kg
Mass of water that gives rise to 345.36 kg of steam = 1.4925 × 345.36
= 515.63 kg
Therefore, the mass of water that is heated is 100 + 515.63 = 615.63 kg.
To find the heat supplied we use the formula;
Q = mLm = 345.36 kg of steam
L = 2246.9 kJ/kg (at 750 kPa, from steam tables)
Q = 345.36 × 2246.9
Q = 775528.4 kJ
The amount of heat that must be supplied to 100 kg of water at 30°C to make steam at 750 kPa that is 67% dry is 775528.4 kJ.
To know more about heat visit:
https://brainly.com/question/13860901
#SPJ11
6. Which characteristics correctly describe a proton? a) approximate mass 1 amu; charge +1; inside nucleus b) approximate mass 5 x 104 amu; charge -1; outside nucleus c) aproximate mass 5 x 104 amu; charge +1; inside nucleus d) approximate mass 1 amu; charge 0; inside nucleus e) approximate mass 1 amu; charge +1; outside nucleus
The correct characteristic that describes a proton is: a) approximate mass 1 amu; charge +1; inside nucleus.
A proton is a subatomic particle with a positive charge and a mass of approximately 1 atomic mass unit (amu). It is located inside the nucleus of an atom. Protons are fundamental particles found in all atomic nuclei and play a crucial role in determining the atomic number and identity of an element. Their positive charge balances the negative charge of electrons, creating a neutral atom.
To know more about nucleus,
https://brainly.com/question/25663043
#SPJ11
A tank full of Argon is leaking through a very small hole. The system is composed of a tank of fixed volume put in a room at fixed pressure. Q1-1 State the low of perfect gases and define the units for each component. Express it in terms of moles and mass variables. (5 points) Q1-2 Derive in general terms the mass rate (dm/dt) as a function of time for a system of constant volume and temperature, considering only pressure as the other variable. (5 points) Q1-3 Calculate the time required in hours for the pressure to be reduced from an initial 1000 kPa to a pressure of 500 kPa. We assume that the tank is, apart from the small hole, a closed system (no dm(in)/dt component) (10 points) Q1-4 Calculate the pressure in the tank after 5 min of leakage starting from a 500 kPa pressure (5 points) Notes. Use any of the following and relevant constants and information for the calculations. Area of the disk-shaped hole in the tank: A 10-6 m2 Molecular mass of Argon gas: 39.9 g/mol Tank volume: 5 m3 R=516 J/(kg.K) T-300C Leakage rate (mass rate out of the system): m-0.66pA/√(RT)
We can use the ideal gas law and the mass rate formula to calculate the time required for the pressure to be reduced from an initial 1000 kPa to a pressure of 500 kPa. The time t is 32.95 hours.
The law of perfect gases is also known as Ideal Gas Law. It describes the behavior of a gas when all its variables are kept constant. It is given as follows:
pV = nRT
Where p is pressure, V is volume, n is the number of moles, R is the gas constant, and T is temperature.
The unit for pressure is Pascals (Pa), volume is cubic meters (m³), number of moles is moles (mol), gas constant is joules per Kelvin per mole (J/mol.K), and temperature is Kelvin (K).
We have constant volume (V) and temperature (T), and we are considering only pressure (p) as the variable. We can use this formula:
dm/dt = -pA√(RT/M)
The rate of mass is (dm/dt), pressure is p, the area of the hole is A, R is the gas constant, T is the temperature, and M is the molar mass of the gas.
The negative sign indicates that the mass rate is flowing out of the tank
We have:
Initial pressure (P1) = 1000 kPa
Final pressure (P2) = 500 kPa
Leakage rate (m) = 0.66pA√(RT/M)
The leakage rate can be written as dm/dt = -0.66pA√(RT/M)
We have a constant volume (V), so we can write:
pV = nRT
The number of moles can be written as:
n = (pV)/(RT)
We can use this formula for the ideal gas law:
pV = nRT
We can substitute this into our mass rate formula to get:
-0.66pA√(RT/M) = -dm/dt(pV/M) (A)(√(RT/M))
Substitute the values of A, p, R, T, M, P1, and P2 to get:
[tex](1000*5*10⁻⁶)/(39.9*516*(273+27)) = ln(1000/500)[/tex]
[tex]t = (5*10⁻⁶)/(0.66*(10⁻⁶)*√(516*5*39.9/0.66))*(ln(1000/500))[/tex]
t = 32.95 hours
We can use the ideal gas law and the mass rate formula to calculate the time required for the pressure to be reduced from an initial 1000 kPa to a pressure of 500 kPa. We can write pV = nRT to get the number of moles as n = (pV)/(RT).
We can substitute this into our mass rate formula to get -
[tex]0.66pA √(RT/M) = -dm/dt(pV/M)(A)(√(RT/M)).[/tex]
We substitute the values of A, p, R, T, M, P1, and P2 to get [tex](1000*5*10⁻⁶)/(39.9*516*(273+27)) = ln(1000/500).[/tex]
The time is t = [tex](5*10⁻⁶)/(0.66*(10⁻⁶)*√(516*5*39.9/0.66))*(ln(1000/500)),[/tex]which is 32.95 hours.
To know more about temperature visit:
brainly.com/question/7510619
#SPJ11
A beverage manufacturer has recently commissioned a 500 m aerated tank to biologically treat 4x105 L/d of wastewater prior to discharge. The tank is a single-pass configuration not catering for recycle. Regulations are particularly stringent requiring that the discharged waste does not exceed 10 mg BOD/L owing to the sensitive receiving environment. You have been specifically asked to determine whether the current tank volume is adequate. If not, determine the maximum flow that can be treated while still meeting the BOD discharge requirement with the existing tank. If the mixed liquor suspended solids concentration in the tank is to be set at 1500 mg /L, determine the maximum concentration of BOD in the influent that may be adequately treated. Quantify how much solid material will be discharged per day. [data: Umax = 3 mg VSS/mg VSS.d; Ks = 30 mg/L as BOD; Y = 0.6 mg VSS/mg BOD] =
The solid material that will be discharged per day is 3816.7 g/d. The maximum flow that can be treated while still meeting the BOD discharge requirement with the existing tank is 4.00 x 10³ L/d. Hence, maximum concentration of BOD in the influent that may be adequately treated is 59.97 mg/L.
The maximum flow that can be treated while still meeting the BOD discharge requirement with the existing tank is 4.00 x 10³ L/d.
Given:Q = 4 × 10^5 L/dV = 500 m³Ks = 30 mg/LY = 0.6 mg VSS/mg BODUmax = 3 mg VSS/mg VSS.dSs = 1500 mg/Lsmax = 0.50 g/L
We are to determine whether the current tank volume is adequate. If not, determine the maximum flow that can be treated while still meeting the BOD discharge requirement with the existing tank.
If the mixed liquor suspended solids concentration in the tank is to be set at 1500 mg/L, determine the maximum concentration of BOD in the influent that may be adequately treated. Quantify how much solid material will be discharged per day.
Solution: For a single-pass configuration with no recycling, we have;
Where S0 = influent BOD concentration in mg/LX = MLSS concentration in mg/LSo, we can write the equation for the tank as; We have a discharge standard of 10 mg BOD/L.
Hence, we can say that; Therefore; Also, by rearranging equation 3, we can write that; The oxygen uptake rate (OUR) can be expressed as; We can substitute equation 6 in equation 5 to get; The solids loading rate (SLR) can be defined as; From the oxygen mass balance; Therefore; The rate of oxygen supply can be expressed as; From the F/M ratio;Where; V = Tank volume = 500 m³
Learn more about solid material
https://brainly.com/question/29783885
#SPJ11
Q3.: Using the mix proportion 1:0.61:2.02: 4.07, how much of each individual ingredient (Portland Cement, Water, Sand and Gravel) should be used to cast Ten beams with the following dimension (length = 5m, width = 0.35m, Depth = 0.6m) and Nine cubes with the following dimension (150 x 150 x 150 mm)? (Consider 8% extra amount). The Density of concrete is 2400 kg/m3. Consider the following properties for the aggregates used: (a) Coarse aggregate: Moisture Content (SSD) of -0.15%. (b) The fine aggregate • Moisture Content (SSD) of 0.85%. Note: 1) Calculations of water content should be adjusted to account for stock aggregates' absorption capacity and moisture content. 2) Final weight of sand and gravel should reflect the stock weight.
To cast ten beams and nine cubes with the given dimensions and mix proportion, the following amounts of each ingredient should be used: Portland Cement, Water, Sand, and Gravel.
Calculate the total volume of concrete required.
To calculate the total volume of concrete required, we need to determine the volume of each beam and cube and multiply it by the respective quantities needed per unit volume based on the mix proportion. Considering the given dimensions, we can calculate the total volume required for all the beams and cubes.
Adjust the quantities to account for stock aggregates' absorption capacity and moisture content.
Since the aggregates have moisture content and absorption capacity, we need to adjust the quantities of water, sand, and gravel to compensate for these factors. By considering the moisture content and absorption capacity, we can determine the adjusted quantities of these ingredients.
Calculate the amounts of each ingredient.
By applying the mix proportion and considering the adjusted quantities, we can determine the amounts of Portland Cement, Water, Sand, and Gravel required to cast the ten beams and nine cubes. These quantities will ensure that the concrete mix is in accordance with the given mix proportion and takes into account the adjustments for moisture content and absorption capacity.
Learn more about dimensions.
brainly.com/question/33718611
#SPJ11
[10] Delicious Desserts Inc. is considering the purchase of pie making equipment that would result in the following annual project cash flows. (a) Using the conventional payback period method, find the payback period for the project. (show work in the table below; use interpolation to improve the final value) (b) Find the payback period using the discounted-payback period method. Assume the cost of funds to be 15%. (show work in the table below; use interpolation to improve the final value)
The payback period for the project is 3.55 years.
To calculate the payback period using the conventional method, we need to determine the point at which the cumulative cash flow becomes equal to or greater than the initial investment.
Given the following annual project cash flows:
Year 1: $50,000
Year 2: $60,000
Year 3: $70,000
Year 4: $80,000
Year 5: $90,000
Year 6: $100,000
We need to find the payback period when the cumulative cash flow reaches or exceeds the initial investment of $400,000.
By analyzing the cash flows and calculating the cumulative cash flow at the end of each year, we can determine that the payback point falls between year 3 and year 4. The cumulative cash flow at the end of year 3 is $180,000, and the cumulative cash flow at the end of year 4 is $260,000.
To calculate the precise payback period, we interpolate the fraction of the year needed to reach the payback point.
Fraction of the year = (Cumulative cash flow at the end of the year before reaching the payback point - Initial investment) / Cash flow in the payback year
Fraction of the year = ($260,000 - $400,000) / $80,000
Fraction of the year = -0.45
Payback period = Number of years before reaching the payback point + Fraction of the year
Payback period = 4 + (-0.45)
Payback period = 3.55 years
Therefore, using the conventional payback period method, the payback period for the project is 3.55 years.
Learn more about investment: https://brainly.com/question/29547577
#SPJ11
Compute the volume of the solid bounded by the hemisphere z = √4c²-x² - y² and the horizontal plane z = c by using spherical coordinates, where c> 0.
The volume of the solid bounded by the hemisphere z = √(4c² - x² - y²) and the horizontal plane z = c, using spherical coordinates, is π²c⁴/36.
Understanding HemisphereIn spherical coordinates, the variables are typically denoted as ρ, θ, and φ.
ρ = the radial distance from the origin to the point in space,
θ = the azimuthal angle measured from the positive x-axis in the xy-plane, and
φ = the polar angle measured from the positive z-axis.
Given that the hemisphere is defined as:
z = √(4c² - x² - y²)
and the horizontal plane is defined as:\
z = c
we can see that the limits for the variables ρ, θ, and φ are as follows:
ρ: 0 to c
θ: 0 to 2π (a full circle)
φ: 0 to π/2 (since the hemisphere lies above the xy-plane)
Now, let's calculate the volume using the integral in spherical coordinates:
V = ∫∫∫ ρ² sin(φ) dρ dθ dφ
Where the limits for the integrals are:
ρ: 0 to c
θ: 0 to 2π
φ: 0 to π/2
Let's evaluate this integral step by step:
V = ∫∫∫ ρ² sin(φ) dρ dθ dφ
= [tex]\int\limits^{\frac{\pi}{2} }_0\int\limits^{2\pi}_0 \int\limits^c_0 {\rho^{2} sin(\phi)} \, d {\rho} \, d {\theta} \, d\phi[/tex]
We can integrate the ρ integral first:
V = [tex]\int\limits^{\frac{\pi}{2} }_0\int\limits^{2\pi}_0 \[\frac{\rho^{3}}{3} sin(\phi)]} \, d {\theta} \, d\phi[/tex]
= [tex]\frac{1}{3} \int\limits^{\frac{\pi}{2} }_0\int\limits^{2\pi}_0 \[\rho^{3}sin(\phi)]} \, d {\theta} \, d\phi[/tex]
Next, we integrate the θ integral:
V = (1/3) ∫₀^(π/2) [- (ρ³/3) cos(φ)]₀^(2π) dφ
= (1/3) ∫₀^(π/2) (-2πρ³/3) dφ
Finally, we integrate the φ integral:
V = (1/3) [- (2πρ³/3) φ]₀^(π/2)
= (1/3) (- (2πρ³/3) (π/2))
= -π²ρ³/9
Now, substituting the limits for ρ:
V = -π²/9 ∫₀^(π/2) ρ³ dφ
= -π²/9 [(ρ⁴/4)]₀^(π/2)
= -π²/9 [(c⁴/4) - (0/4)]
= -π²c⁴/36
Finally, taking the absolute value of the volume:
|V| = π²c⁴/36
Learn more about hemisphere here:
https://brainly.com/question/333717
#SPJ4
Question 4 Find the volume of the solid in the first octant (where x,y,z≥0 ) bounded by the coordinate planes x=0,y=0,z=0 and the surface z=1−y−x^2 (a good first step would be to find where the surface intersects the xy-plane, which will tell you the domain of integration).
The bounds of integration for the volume of the solid in the first octant are as follows:
x: -1 to 1
y: 0 to 1−x^2
z: 0 to 1−y−x^2
To calculate the volume, we can use a triple integral with these bounds:
V = ∫∫∫ dz dy dx
where the integration is done over the specified bounds.
To find the volume of the solid in the first octant bounded by the coordinate planes x=0, y=0, z=0, and the surface z=1−y−x^2, we can start by finding where the surface intersects the xy-plane. This will give us the domain of integration.
To find the intersection points, we set z=0 in the equation of the surface:
0 = 1−y−x^2
Simplifying this equation, we get:
y = 1−x^2
So, the surface intersects the xy-plane along the curve y = 1−x^2.
Now, we can find the bounds for integration in the xy-plane. The curve y = 1−x^2 is a parabola that opens downwards. To find the x-bounds, we need to find the x-values where the curve intersects the x-axis (y=0).
Setting y=0 in the equation y = 1−x^2, we get:
0 = 1−x^2
Rearranging this equation, we have:
x^2 = 1
Taking the square root of both sides, we get two solutions:
x = 1 or x = -1
Therefore, the x-bounds of integration are -1 to 1.
Now, we need to find the y-bounds of integration. Since the curve y = 1−x^2 is entirely above the x-axis, the y-bounds will be from 0 to 1−x^2.
Finally, the z-bounds of integration are from 0 to 1−y−x^2, as mentioned in the question.
To learn more about integration visit : https://brainly.com/question/30094386
#SPJ11
Cauchy's theorem is a big theorem which we will use often. Right away it reveals a number of interesting and useful properties of analytic functions. Find at least two practical applications of this theorem.
Cauchy's theorem is a fundamental result in complex analysis that has several practical applications.
Here are two examples:
1. Calculating contour integrals:
One practical application of Cauchy's theorem is in calculating contour integrals.
A contour integral is an integral along a closed curve in the complex plane.
Cauchy's theorem states that if a function is analytic within and on a closed curve, then the value of the contour integral of the function around that curve is zero.
This property allows us to simplify the calculation of certain integrals by considering paths that are easier to work with.
For example, if we have a complex function defined on a circle, we can use Cauchy's theorem to replace the circle with a simpler path, such as a line segment, and calculate the integral along that path instead.
2. Evaluating real integrals:
Another practical application of Cauchy's theorem is in evaluating real integrals.
By using a technique called the "keyhole contour," we can convert real integrals into contour integrals and apply Cauchy's theorem to simplify the calculation.
The keyhole contour involves choosing a closed curve that encloses the real line and includes a small circular arc around the singularity of the integrand, if there is one.
Then, by applying Cauchy's theorem, we can show that the contour integral along this keyhole contour is equal to the sum of the integrals along the real line and the circular arc.
This allows us to evaluate real integrals by calculating the contour integral, which can often be easier to handle due to the properties of analytic functions.
These are just two practical applications of Cauchy's theorem, but it is worth mentioning that this theorem has many other important applications in various branches of mathematics, such as complex analysis, potential theory, and physics.
Its versatility and usefulness make it a powerful tool for understanding and solving problems involving analytic functions.
Learn more about Cauchy's theorem from this link:
https://brainly.com/question/31058232
#SPJ11
Consider the following system of linear equations 2x+8y-z = 11 5x -y + z = 10. -x + y + 4z = 3 Use Jacobi's iterative method, starting at x=0, y=0 y z=0; apply 3 iterations. (Carry out the development by hand and its implementation in Octave, otherwise its development will not be credible)
The solution of the given system of linear equations using Jacobi's iterative method is (4.092, 1.72, 1.341).
The given system of linear equations is 2x+8y-z = 11 5x -y + z = 10 -x + y + 4z = 3
Jacobi's iterative method is given as follows,
[tex]\[\left\{ \begin{matrix} {x}_{i+1}=\frac{1}{2}(11-8{y}_{i}+{z}_{i}) \\ {y}_{i+1}=\frac{1}{5}(10+{x}_{i}+{z}_{i}) \\ {z}_{i+1}=\frac{1}{4}(3+{x}_{i}-{y}_{i}) \end{matrix} \right.\][/tex]
With initial values: x = 0, y = 0, z = 0
The first three iterations of Jacobi's method are given below:
Initial guess: (0, 0, 0)
First Iteration: [tex]\[x_{1}=5.5,y_{1}=2,z_{1}=0.75\][/tex]
Second Iteration: [tex]\[x_{2}=4.875,y_{2}=1.15,z_{2}=1.688\][/tex]
Third Iteration:[tex]\[x_{3}=4.092,y_{3}=1.72,z_{3}=1.341\][/tex]
The values of x, y and z after three iterations of Jacobi's method are as follows:
x = 4.092, y = 1.72, z = 1.341
Therefore, the solution of the given system of linear equations using Jacobi's iterative method is (4.092, 1.72, 1.341).
To know more about Jacobi's iterative method visit:
https://brainly.com/question/32594080
#SPJ11
The viscosity of the synthesized polymer sample was measured by a falling steel ball viscometer. If the time taken for the steel ball (diameter (D) = 0.03 m and distance (L) = 0.5 m) to fall along L is 25 seconds, then the viscosity of the polymer is... Pa.s. (p = 7500 kg/m and = 800 kg/m) a. 656.6 b. 3324.1 c. 2954.7 d. 164.2
The viscosity of the synthesized polymer sample was found to be 2954.7 Pa.s by measuring it using a falling steel ball viscometer.
The given parameters are:
Diameter (D) = 0.03 m
Distance (L) = 0.5 m
Time (t) = 25 sec
Density of the steel ball (p) = 7500 kg/m³
Density of the polymer sample (μ) = 800 kg/m³
Viscosity of the polymer is given by the formula:η = 2pD²Lg/9t(μ - p)
The viscosity of the polymer can be calculated as follows:
η = 2(7500) (0.03)² (0.5) (9.81)/9(25) (800 - 7500)
η = 2954.7 Pa.s
Thus, the viscosity of the synthesized polymer sample was found to be 2954.7 Pa.s by measuring it using a falling steel ball viscometer.
To know more about viscosity, click here
https://brainly.com/question/30759211
#SPJ11