The work is done by the man against gravity in climbing to the top with a 20 lb can of paint up a helical staircase that encircles a silo with a radius of 15 ft. if the silo is 120 ft high and the man makes exactly four complete revolutions is 25200 lb-ft.
What is Work done?When an external force moves an object over a distance, at least a portion of that force must be exerted in the direction of the displacement. Physics refers to this as work. If the force acting along the path is constant, the amount of work can be calculated by multiplying the length of the path by the force's component.
Formally, W = fd means that the work is equal to the force f times the length d. If the force is applied at an angle to the displacement, the work is W = fd cos.
Given:
The mass of man, m = 200 lb,
The mass of the can, M = 20 lb,
Calculate the work done y the following formula,
W = [tex]\int\limits^{120}_0} \,(215 -1/12y ) dy[/tex]
Here W is work done
Integrate the above equation, and we get,
W = 25200 lb ft.
Therefore, work is done by the man against gravity in climbing to the top with a 20 lb can of paint up a helical staircase that encircles a silo with a radius of 15 ft. if the silo is 120 ft high and the man makes exactly four complete revolutions is 25200 lb ft.
To know more about Work done:
https://brainly.com/question/13662169
#SPJ1
What is the velocity (in m/s) of a 0.179kg billiard ball of its wavelength is 7.83cm
Answer: 472.556m⋅s−1
Explanation: λ=7.83cm=7.83⋅(1cm)=7.83⋅(1cm×0.01m1cm)=0.0783m
if you were travelling outward from the earth in a space shuttle at an altitude of 68.9 km you would be in the
The virtually massless subatomic particle known as a neutrino seldom interacts with ordinary matter and travels through space at nearly the speed of light.
Although they can originate from a wide range of sources, the majority of neutrinos that travel through the Earth come from the Sun, which beams untold quantities of them our way every second. The vast majority of these neutrinos travel through the Earth and you and then emerge from the other side as if nothing ever happened. About 100 billion neutrinos from the Sun pass through your thumb each second to give you an idea of scale. If you extrapolate that to Earth, you end up with a lot of zeros.
Learn more about neutrino here-
https://brainly.com/question/27870530
#SPJ4
Corey, whose mass is 95 kg , stands on a bathroom scale in an elevator. The scale reads 890 n for the first 3. 0 s after the elevator starts to move, then 930 n for the next 3. 0 s.
The velocity of the elevator would be v₂ = 2.568 m/s
Given that,
mass of Corey = 95 Kg
reading of sale for first 3 s when elevator start to move = 890 N
scale reading for the next 3.0 s = 930 N
Gravitational force acting = F = m g
F = 95 x 9.8
F = 931 N
using Newton's second law, due to movement of elevator
F. = m a
W - N = m a₁
930- 890 = 95 x a₁
a₁ = 0.421 m/s²
Now,
velocity calculation
v₁ = a₁t
v₁ = 0.421 x 3 = 1.263 m/s
For second case
931 - 930 = 95 x a₂
a₂ = 0.011 m/s²
now, velocity after 4 s
v₂ = v₁ + a₂ t
v₂ = 2.557+ 0.011 x (4 - 3)
Because velocity after 3 seconds is calculated we need to calculate velocity after 4 s from beginning.
v₂ = 2.557 + 0.011
v₂ = 2.568 m/s
velocity of the elevator is equal to v₂ =2.568 m/s
To know more about Newton law from the given link
https://brainly.com/question/25842103
#SPJ4
A 1000-kg car is moving at 30 m/s around a horizontal unbanked curve whose radius is 100 m. What is the magnitude of the friction force required to keep the car from sliding?.
The magnitude of the friction force required to keep the car from sliding is 13112 N.
Calculation:-
friction force = centripetal force
= mv^2 / R
= 1000*30^2 / (200/2)
= 9000 N
so option B) 9000 N is the correct answer
15) net force = mv^2 / R
= 250*(96.5*5/18)^2 / 13.7
= 13112 N = 1.31*10^4 N
Friction is the force resisting the relative motion of sturdy surfaces, fluid layers, and material factors sliding towards each specific. There are numerous styles of friction Dry friction is a strain that opposes the relative lateral movement of two stable surfaces in touch.
Friction is the shape of contact pressure. It exists between the surfaces that are in touch. The frictional force relies upon the character of the floor in contact. The rougher the ground, the extra friction is involved. The frictional force is proportional to the urgent pressure, which is the burden of the body. it's miles impartial of the place of the touch.
Learn more about friction here:-https://brainly.com/question/24338873
#SPJ4
Need help with both questions
Answer: 2) c 3) c
Explanation:
The difference between starting time and ending time is the elapsed time.
F = ma (Newton's 2nd Law of Motion)
an 8.0-g bullet is shot into a 4.0-kg block, at rest on a frictionless horizontal surface (see the figure). the bullet remains lodged in the block. the block moves into an ideal massless spring and compresses it by 8.7 cm. the spring constant of the spring is 2400 n/m. the initial velocity of the bullet is closest to
The velocity of the bullet is 1100 m/s.
When the bullet lodges into the block, as there is no net external force, the momentum of the system will be conserved. After that when the block + bullet system compresses the spring, the energy of the system remains conserved. The kinetic energy is conserved into the potential energy of the spring.
Velocity is the directional speed of an object in movement as an illustration of its price of the trade-in position as found from a particular frame of reference and as measured through a specific standard of time.
Calculation:-
Mass of block, M = 4 Kg
Mass of bullet, m = 8 g = 0.008 Kg
Compression in spring, x = 8.7cm = 0.087 m
Let's first solve the energy conservation,
K.E. = P.E.
(1/2)(M+m)V2 = (1/2)kx2
V2 = 2400*(0.087)2/(4+0.008)
V2 = 4.53
V = 2.13 m/s
Now, conserving the momentum,
mv = (M+m)*V
v = (4+0.008)*2.13/0.008
The velocity of the bullet, v = 1066.6 m/s
Rounding to the velocity as 1100 m/s
Learn more about velocity here:-https://brainly.com/question/24445340
#SPJ4
what is the moment of inertia if you twirl a large ring around your finger, so that in essence it rotates about a point on the ring, about an axis parallel to the symmetry axis?
The moment of inertia of large ring is 2MR².
What is inertia?
Inertia is the propensity of a body to resist any alteration to its state of regular motion or of rest.
Given that,
Mass of ring = M
Radius of ring = R
Therefore, moment of inertia of ring = MR²
as we need to calculate the moment of inertia of large ring
Therefore, we need to use the formula of moment of inertia
I = I + MR²
Where I = moment of inertia at centre of mass
As we said,
Mass of ring = M
Radius of ring = R
By puting the value of above into the formula, we get
I = MR² + MR²
I = 2MR²
Therefore, The moment of inertia of large ring is 2MR².
To learn more about inertia
Here: https://brainly.com/question/1140505
#SPJ4
The moment of inertia of large ring is 2MR².
What is inertia?
Inertia is the propensity of a body to resist any alteration to its state of regular motion or of rest.
Given that,
Mass of ring = M
Radius of ring = R
Therefore, moment of inertia of ring = MR²
as we need to calculate the moment of inertia of large ring
Therefore, we need to use the formula of moment of inertia
I = I + MR²
Where I = moment of inertia at centre of mass
As we said,
Mass of ring = M
Radius of ring = R
By puting the value of above into the formula, we get
I = MR² + MR²
I = 2MR²
Therefore, The moment of inertia of large ring is 2MR².
To learn more about inertia
brainly.com/question/1140505
#SPJ4
If a car collides with a moving bus, what type of relationship exists between the force of the car and the force of the bus?.
The correct answer is forces are equal but opposite in direction between car and bus.
What do we mean by Collision?
When two objects collide, forces of equal magnitude and opposite direction are applied to each object. Such pressures frequently result in one thing gaining momentum and gaining speed while the other object slows down (lose momentum).
The force applied to an object to cause an impact—a change in momentum—on it is referred to as the impact force, or momentum. Technically speaking, the Car and the bus would have exerted and felt the same amount of impact force in the event of a collision. Because every action has a corresponding and opposing response, according to Newton's third law.
To learn more about Collision from the given link
https://brainly.com/question/24915434
#SPJ4
an electron is moving with a velocity of 4.3 x 106 m/s in a uniform magnetic field of strength 3.5 t. the velocity vector makes a 55o angle with the magnetic field. what is the magnitude of the magnetic force on the electron?
The magnetic force on the electron is 2 x 10^(-12) N
What is the magnitude of the magnetic force on the electron?
Magnetic force can be defined as the attraction or repulsion force that arises between electrically charged particles because of their motion.
The velocity of the electron is
v = 4.3 x 106 m/s
The strength of the uniform magnetic field is B = 3.5 T
The angle between the velocity of the electron and the magnetic field is 55 degrees.
Also, the charge on the electron is
e = 1.6 X 10 power minus 19 C
The magnetic force can be calculated as
F = Bev sin θ
Substituting the given values we can find the total magnetic force.
The magnetic force on the electron is 2 x 10^(-12) N
To know more about Magnetic Force from the given link
https://brainly.com/question/25932320
#SPJ4
How does the angle at which a ray of light strikes a pane of window glass compare with the angle at which it passes out the other side?.
The angle of incidence equals the angle of reflection. When a ray of light strikes a pane of window glass at a perpendicular angle, it passes through the glass and exits at a perpendicular angle on the other side.
However, if the ray of light strikes the glass at an angle, it is reflected off the surface of the glass at the same angle.The angle of incidence (angle at which a ray of light strikes a pane of window glass) is equal to the angle of refraction (angle at which it passes out the other side).
This is because when light hits a surface at an angle, it bounces off at the same angle. The angle of incidence is the angle between the ray of light and the perpendicular to the surface. The angle of refraction is the angle between the ray of light and the perpendicular to the surface.
Learn more about angle of incidence at : https://brainly.com/question/12370040
#SPJ4
The ladder shown is 3.0 m long and the coefficient of static friction between the floor and ladder is 0.50. There is no friction between the wall and the ladder. What is the minimum angle (in degrees) that the ladder can make with the floor without slipping?
This is a static equilibrium problem. The sum of the torques equals zero, the sum of the forces along x equals zero, and the sum of the forces along y equals zero. Use the point where the ladder contacts the ground as the axis of rotation. At the minimum angle, you're getting the maximum possible value of static
45° s the minimum angle (in degrees) that the ladder can make with the floor without slipping defying friction.
F=μmg
" Moment along the bottom of ladder "
[tex]0.5 Lmg cos \theta=LF_wsin \theta[/tex]
[tex]0.5 Lmg cos \theta=L \mu mg sin \theta[/tex]
[tex]0.5 cos \theta=mu sin \theta[/tex]
[tex]\theta=tan^-1(0.5 )/(\mu)[/tex]
Θ= 45°
Physical friction is all around us. Static friction is the resistance to an object moving along a route. Finally, explain it with a simple example. Consider the common activity we all engage in: walking. While working, we are continuously in contact with the floor. As we advance our feet, motion pushes on the earth as we travel backward.
The fact that friction operates in the opposite direction from relative motion is one important aspect to be aware of in order to decrease friction. This phenomenon might be helpful for slowing down the action until it eventually stops.
To know more about Friction visit : brainly.com/question/28356847
#SPJ4
5.33 stopping distance. (a) if the coefficient of kinetic friction between tires and dry pavement is 0.80, what is the shortest distance in which you can stop an automobile by locking the brakes when traveling at 28.7 m/s ?
kinetic friction between tires and dry pavement is 0.80 then u = 16.26 m/s is the shortest distance in which you can stop an automobile by locking the brakes when traveling at 28.7 m/s.
μk = 0.80, intial speed u=28.7.m/s final velocity v=0
by applying newton's law to the body
-μk mg = ma
a = -μk g = - 7.84 m/s^2
from v^2 - u^2 = 2as
s = v^2 - u^2 /2a = 54 m
2).μk = 0.25 , s = 54 m ,v=0 , intial speed u =?
a = -μk g = -2.45 m/s^2
v^2 - u^2 = 2as
u^2 = 2*2.45 *54
we get u = 16.26 m/s
In most cases, kinetic friction is less intense than the amount of force required to overcome static friction. When an object is already moving, kinetic friction occurs. A force must be applied to an object that precisely balances the force from kinetic friction in order to maintain that object's motion at a constant speed.
Learn more about kinetic friction here:
https://brainly.com/question/17237604
#SPJ4
As a baseball is being caught, its speed goes from 30.0 m/s to 0.0 m/s in about 0.0050 s. The mass of the baseball is 0.145 kg.
What is the baseball's acceleration?
What are the magnitude and the direction of the force acting on it?
What are the magnitude and direction of the force acting on the player who caught it?
Answer: Force = 870 N
Explanation:
acceleration = a = (final velocity - initial velocity) / time elapsed
a = (0-30)/.005 = -6000 m/s2 (negative sign means the ball is slowing down)
Force = F = mass x acceleration = ma
F = (0.145 kg)(6000 m/s2) = 870 N away from the player throwing the ball
The magnitude of the force on the player catching the ball is equal, 870N. The mitt acts on the ball with an equal and opposite force (Newton's 3rd Law of Motion)
cables provide most of the support to keep a suspension bridge up. the elastic force of tension pulling u is 28,000 N and the force of gravity is 28,000 N down. find the net force
The net force to keep a suspension bridge up is zero, 0N.
An action-reaction pair of forces acting at each end of the aforementioned elements is tension. Consider a rope. Aside from the ends, every portion of the rope experiences tension force in both directions. The attached weight exerts force and tension on one side of the ends. The tension of the string fluctuates under different conditions. The net force formula is provided by when the body is at rest.
The tension exerted on an item is determined by adding the products of its mass, acceleration, and gravitational force. It is denoted mathematically as follows:
T = mg + ma
Where,
T is tension
m is mass
a is acceleration
g is the acceleration due to gravity
Here,
T = 28000N
mg = 28000N
ma = T - mg
ma = 28000 - 28000
ma = 0N
The net force to keep a suspension bridge up is zero, 0N.
Learn more about tension here:
https://brainly.com/question/14294135
#SPJ1
Find fmin f m i n , the constant force with the least magnitude that must be applied to the board in order to pull the board out from under the the box (which will then fall off of the opposite end of the board).
F(min) = μsg(m1+m2) the constant force with the least magnitude that must be applied to the board in order to pull the board out from under the the box.
What is magnitude?In physics, size is simply defined as magnitude. It represents the absolute or relative direction or magnitude that an object is moving in the sense of motion. Used to describe the size or extent of something.In physics, size generally refers to distance or quantity. Simply put, quantities are quantities of quantities.For example, the magnitude of an earthquake measured on the Richter scale typically varies between 1 and 10, representing the magnitude of the earthquake. A magnitude 8 earthquake is much more severe than a magnitude 3 earthquake. A force magnitude is a number that expresses the strength of a force. for example: Assume a force of 10 N to the east."East" represents the direction, and "10" represents the strength of the force. A quantity is therefore basically a "value" or "amount" of a physical quantity.To learn more about magnitude from the given link :
https://brainly.com/question/14452091
#SPJ4
how close were your wavelength measurements to the accepted values of wavelengths for the various gases as listed below? what factors do you think might have contributed to any differences, and how might they have affected your measurements?
The accepted values of wavelengths for Hydrogen is a simple atom with a simple spectrum. Besides the three lines we may be able to see in 410 nm.
Gamma rays have incredibly short wavelengths that are only a small percentage of the size of atoms, but other wavelengths can extend as far as the cosmos, despite the fact that the relationship between wave frequency and wavelength is inverse. Although it is not often stated explicitly, electromagnetic radiation wavelengths are frequently represented in terms of the vacuum wavelength, regardless of the medium they pass through.
Electromagnetic radiation's behavior is influenced by its wavelength. Wavelength times frequency equals the speed of light. Energy is obtained by multiplying frequency by the Planck constant. The wave number in centimeters is 1/wavelength. A rough estimate of the wavelength size is shown along with the wavelengths of various regions of the electromagnetic spectrum.
To know more about wavelength visit : brainly.com/question/14530620
#SPJ4
A 2 kg toy caramels at a speed of 5 m/s if a child applies a three new enforce for 2 m in the same direction the car is already moving how much work is done on the car
The work done on the car is equal to the force applied to the car multiplied by the distance over which that force is applied. In this case, the force is applied for 2 meters, so the work done is equal to 3 Newtons multiplied by 2 meters, or 6 Joules.
What is force?
A force is indeed an influence that can alter an object's motion in physics. An object with mass can change its velocity, or accelerate, as a result of a force. An intuitive way to describe force is as a push or even a pull. A force is a vector quantity because it has both direction and magnitude. It is calculated using the newton SI unit (N). Force is denoted by the letter F. (formerly P). The net force acting on an object seems to be equal to the rate that its momentum changes over time, according to Newton's second law in its original formulation. This law suggests that an object's acceleration is directly proportional to the total force acting on the object if the object's mass remains constant.
Work is defined as force multiplied by distance, so the work done on the car is (3 N)(2 m) = 6 Nm. Since 1 Nm = 1 J, the work done on the car is 6 J.
To learn more about force
https://brainly.com/question/12970081
#SPJ1
what is the average flow rate in cm3/s of gasoline to the engine of a car traveling at 103 km/h if it averages 10.5 km/l?
An automobile going at 103 km/h with an average fuel consumption of 10.5 km/l would have a gasoline flow rate to the engine of 1.03 cm3/s.
What kind of engine is now in a car?Internal combustion engines are found in cars. Internal combustion engines are available in a variety of forms. Gas turbine engines are a different kind from diesel engines. The four-cylinder, boxer-four, straight-six, V6, and V8 engines—the most popular ones—each have advantages and disadvantages of their own.
What do motorized vehicles go by?Vehicles with standard internal combustion engines are known as "internal combustion engine vehicles" (ICEVs) (ICE). With the aid of an oxidizer, the fuel used in ICEV burns inside a combustion chamber (typically oxygen from the air). In other words, ICEVs actually burn fuel to generate electricity.
To know more about engine visit:
https://brainly.com/question/14603564
#SPJ4
A 20 m long, uniform bridge of weight 100 kN is supported at each end by pillars, as shown. The pillars exert forces T₁ and T2 on the ends of the bridge. What are the values of T₁ and T2 when a van of weight 24 kN is on the bridge, 5 m from the left-hand pillar?
Answer
T1=68 kN
Explanation:
A 20 m long, uniform bridge of weight 100 kN is supported at each end by pillars, as shown. The pillars exert forces T₁ and T2 on the ends of the bridge. What are the values of T₁ and T2 when a van of weight 24 kN is on the bridge, 5 m from the left-hand pillar is T1=68 kN
What are the types of force ?Force can be defined as pushing or pulling of any object resulting from the object’s interaction or movement, without force the objects can not be moved, can be stopped or change the direction.
Force is a quantitative interaction between two physical bodies, means an object and its environment, there are different types of forces in nature.
If an object in its moving state will be either static or motion, the position of the object will only be changed if it is pushed or pulled and The external push or pull upon the object called as Force.
The contact force types are the force that occurs when we apply some effort on an object such as Spring Force, Applied Force, Air Resistance Force, Normal Force, Tension Force, Frictional Force
Non-Contact forces are another type of forces occur from a distance such as Electromagnetic Force, Gravitational Force, Nuclear Force
For more details Force, visit
brainly.com/question/13691251
#SPJ2
A ball is pushed downhill with an initial velocity of 3. 0 m/s. The ball rolls down a hill with a constant acceleration of 1. 6 m/s2. The ball reaches the bottom of the hill in 6. 0 s. What is the ball's velocity at the bottom of the hill?.
The ball's velocity at the bottom of the hill is 12.6 m/s. The direction of a body or object's movement is defined by its velocity. In its basic form, speed is a scalar quantity.
Velocity can be defined as the rate at which something moves in a specific direction. as the speed of a car driving north on a highway or the pace at which a rocket takes off. Because the velocity vector is scalar, its absolute value magnitude will always equal the motion's speed. Additionally, it is inversely proportional to transit duration and proportionate to displacement. Its measurement is in meters per second (m/s). The velocity formula is shown below: V = s/t.
Where V is the end velocity, u the beginning velocity, a the acceleration, and t the duration,
We obtain the response by substituting the data. 12.6 m/s.
Learn more about velocity here-
https://brainly.com/question/18084516
#SPJ4
A student builds an electromagnet using a battery, an iron nail. And some insulated wire. The wire is wrapped around the nail 50 times and then connected to the battery. What changes could the student make to increase the strength of the electromagnet?.
To enhance the strength of the electromagnet, the student must enlarge the nail, wrap additional wire around the nail, increase the voltage of the battery, and enlarge the nail.
How does an electromagnet work?An electromagnet's mechanics are not extremely sophisticated. Wrapping a piece of conductive wire, usually copper, around a metal object accomplishes the task.
Until electricity is applied, this looks to be nothing more than a jumbled collection of parts, much like Frankenstein's monster.
An electromagnet, on the other hand, does not need to be activated by a storm. A current is introduced and flows through the wire, which can be supplied by a battery or another power source.
Therefore, to enhance the strength of the electromagnet, the student must enlarge the nail, wrap additional wire around the nail, increase the voltage of the battery, and enlarge the nail.
To know more about electromagnet, visit:
https://brainly.com/question/17057080
#SPJ4
if a proton moves from point 1 to point 2 on an isoline with the same voltage, how much work is done
There is no net work done because of absence in any difference between the potentials.
What is work done to shift a proton?The potential difference between two points in a circuit equals the amount of work done in moving a unit charge from one point to another. If the two points are at the same potential, no NET work is done to move the test charge from one point to another. Some parts of the path may have had positive work done, while other parts of the path may have had negative work done.
Work done = Charge × change in potential
W = q × ΔV
q = 1.6 × 10⁻¹⁹ C
ΔV = 0
W = 1.6 × 10⁻¹⁹ × 0
W = 0
To know more about work done visit:
https://brainly.com/question/13014987
#SPJ4
The number of objects that have been observed to be orbiting in the kuiper belt is approximately.
The hundreds of thousands of icy bodies larger than 100 km have been observed to be orbiting in the Kuiper belt is approximately.
What is Kuiper belt?
The region beyond Neptune known as the Kuiper Belt is made up of countless stellar objects orbiting the sun. Solid methane, ice, and ammonia make up belt objects. The belt's orbit deviates from the orbital plane and can be inclined by up to 19 degrees. Scientists searched for Planet X as a possible explanation for the origin of the belt.
What is orbit?
An orbital is a region where it is possible to estimate the likelihood of finding any electron, whereas an orbit is a fixed path that electrons follow around the atom's nucleus.
The Kuiper Belt is thought to contain a trillion comets or more and hundreds of thousands of icy bodies bigger than 100 km (62 miles).
Therefore, there may be hundreds of thousands of icy bodies larger than 100 km have been observed to be orbiting in the Kuiper belt is approximately.
Learn more about Kuiper belt from the given link.
https://brainly.com/question/14154493
#SPJ4
10pa is acting on an area of 0.5m2
Answer:
Explanation:
F = p·A =10·0.5 = 5 N
A 1.5 Kg ball moves in a circle that is 0.4 m radius at a velocity of 5.40 m/s
Centripetal acceleration = v² / r = (5.40 m/s)² / (0.4 m) = 72.9 m/s²
gravity on the moon is 1.6 m/s2. what is the gravitational potential energy of a 1200-kg lander resting on top of a 350-m hill? j
The energy that an object has due to its location in a gravitational field is known as gravitational potential energy. GPE = mgh is the formula for gravitational potential energy. GPE = 1200(1.6)(350) = 672000 J
What is the source of gravitational potential energy?If an object is located at a height that is higher (or lower) than the zero height, it has gravitational potential energy. If an object is situated on an elastic media in a position other than the equilibrium position, it has elastic potential energy.
How is the energy of gravitational potential stored?By utilizing a pump, crane, or engine to raise a mass to a specific height, gravity batteries can store gravitational potential energy. Depending on the mass of the object and also how high it was lifted, the mass now retains a specific gravitational potential energy after being raised.
To know more about gravitational potential energy visit:
https://brainly.com/question/19768887
#SPJ4
How high would a skater need to start on a previous incline to make it up and around a loop that is 6.1meters high?
The skater need to start 7.525 meter high.
Let,
The skater need to start on a previous incline at height = h.
Mass of the skater = m
Given, height of the loop = 6.1 meter.
Radius of the loop; r = 6.1/2 meter = 3.05 meter.
Let to make it up and around a loop that is 6.1meters high, the man required minimum velocity v on the highest point of the loop.
So, centripetal force at highest point = weight of the man
⇒ mv²/r = mg
⇒ v = √(gr)
Then, potential energy of the skater at height h is = mgh.
And, minimum energy of the skater at the highest point of the loop is = potential energy + minimum kinetic energy.
= mg(2r) + 1/2 mv²
= 2mgr + 1/2 mgr
= 5/2 mgr
According to conservation of energy,
potential energy of the skater at height h = minimum energy of the skater at the highest point of the loop
⇒ mgh = 5/2 mgr
⇒ h = 5/2 r =( 5/2 )× 3.05 meter = 7.525 meter.
Hence, required height is 7.525 meter.
Learn more about energy here:
https://brainly.com/question/1932868
#SPJ1
The reason that most seti programs choose to listen at microwave radio frequencies is that.
The reason that most SETI programs choose to listen at microwave radio frequencies is that microwaves are the most energy-efficient way to send information.
What is radio frequencies?Radio frequencies are used in transmitters, receivers, computers, televisions, mobile phones and other communication devices. Radio frequencies are also used in carrier current systems such as telephones and control circuits.In 2021 ARPANSA will publish the standard.Standards for limiting exposure to radio frequency fields - 100 kHz to 300 GHz. The ARPANSA RF standard specifies limits for human exposure to RF EMR in the frequency range 100 kHz to 300 GHz.Microwaves have a frequency range of 109 Hz (1 GHz) to 1000 GHz and corresponding wavelengths of 30 to 0.03 cm. Within this spectrum range there are many important communication system applications in both military and civilian settings.To learn more about radio frequencies from the given link :
https://brainly.com/question/14400059
#SPJ4
a given convex lens has a focal length that varies slightly with the wavelength of the light passing through it. when the a lens is used as the objective of a telescope, this results in
A given convex lens has a focal length that varies slightly with the wavelength of the light passing through it. when the a lens is used as the objective of a telescope, this results in chromatic aberration.
Chromatic aberration is a phenomenon in which light rays passing through a focus of lens at different points, depending on their wavelength. It is a failure of a lens to focus all colors to the same point. It is also called chromatic distortion and spherochromatism. The focal length of the lens varies directly with the wavelength of the light so focal length increases with wavelength but decreases with refractive index as wavelength is inversely related to it. This is the principal cause of chromatic aberration phenomena.
To learn more about chromatic aberration , visit---
https://brainly.com/question/9894093
#SPJ4
A ski lift is used to transport people from the base of a hill to the top. If the lift leaves the base at a velocity of 15. 5 m/s and arrives at the top with a final velocity of 0 m/s, what is the height of the hill? round the answer to the nearest tenth. M.
The heigh of the hill is 12.26m that is calculated from the law of conservation of energy.
What is conservation of energy?In physics, the law of conservation of energy states that the total energy of an isolated system remains constant ; it is said to be conserved over time.
How to calculate the height of the hill using the law of conservation of energy?
The height of the hill can be calculated from the law of conservation of energy as initial velocity (kinetic energy) transforms into potential energy (height).
KE = U
Where,
KE = kinetic energy = 1/2 * mv^2
U = potential energy = mgh
So
1/2 * mv^2 = mgh
h = 1/2 * (v^2)/g
h = 1/2 * 15.5^2/9.8
h = 12.26m (rounded to the nearest tenth)
Learn more about conservation of energy https://brainly.com/question/2137260
#SPJ4