As per the Soderberg theory, the material will fail if σe > Soderberg line σe < Se. The hollow shaft will not fail as per Soderberg's theory.
External diameter (D) = 35 mm
Internal diameter (d) = 25 mm
Length (L) = 500 mm
Cross hole (diameter) = 10 mm
Torsional loads varies between 100 Nm to 50 Nm
Axial load = 500 N
Temperature (T) = 250 ºC
Material: 1040 cd steel
Reliability: 99%
Soderberg's fault theory: In Soderberg's theory, the material failure is calculated with the help of Goodman and Soderberg lines.
Soderberg line is the graphical representation of the maximum stress vs mean stress.
The material is failed if any of the calculated stress crosses the Soderberg line.
Now, we can find the stress due to each type of load acting on the hollow shaft.
Then we can find the equivalent stress and then compare it with the Soderberg line.
1. Stress due to torsional loads:
The torsional shear stress can be calculated as follows:
τmax = (16T/πd³)
Where,
T = maximum torque
d = diameter
[tex]$\tau_{max}=(\frac{16\times 1000}{\pi\times 0.03^3} )[/tex]
= 139 MPa
[tex]$\tau_{min}=(\frac{16T}{\pi d^3} )[/tex]
Where,
T = minimum torque
d = diameter
[tex]$\tau_{min}=(\frac{16\times 500}{\pi\times 0.03^3} )[/tex]
= 70 MPa
2. Stress due to axial load:
The axial stress can be calculated as follows:
σ = P/A
Where,
P = axial load
A = π/4(D²-d²) - π/4d²
For external surface:
σ₁ = 500/[(π/4(0.035² - 0.025²)]
= 104.25 MPa
For internal surface:
σ₂ = 500/[(π/4(0.025²))]
= 403.29 MPa
3. Equivalent stress:
The equivalent stress can be calculated as follows:
[tex]$\sigma_e=(\frac{(\sigma_1+\sigma_2)}{2} )+\sqrt{(\frac{(\sigma_1-\sigma_2)^2}{4+\tau^2} )}[/tex]
[tex]$\sigma_e=(\frac{104.25+403.29}{2} )+\sqrt{\frac{(104.25-403.29)^2}{4+139^2} }[/tex]
[tex]\sigma_e=241.4\ MPa[/tex]
The material fails if σe > Soderberg line
4. Soderberg line:
The Soderberg line can be calculated as follows:
Se = Sa/2 + Sut/2SF
= (1/0.99)
= 1.01
Sut = 585 MPa (lookup value for 1040 cd steel at 250 ºC)
Sa = Sut/2
= 292.5 MPa
Se = 292.5/2 + 585/2
= 438.75 MPa
5. Conclusion:
As per the Soderberg theory, the material will fail if σe > Soderberg line
[tex]\sigma_e[/tex] = 241.4 MPa
[tex]S_e[/tex] = 438.75 MPa
[tex]\sigma_e < S_e[/tex]
Therefore, the hollow shaft will not fail as per Soderberg's theory.
To know more about diameter, visit:
https://brainly.com/question/32968193
#SPJ11
Transition metals and the compounds they form, display beautiful colors due to the nature of light, atomic spectroscopy, electron configurations and metallic characterChoose one transition metal or compound containing a transition metal and explore it.
The compounds formed by transition metals display beautiful colors due to the nature of light, atomic spectroscopy, electron configurations, and metallic character. Let's explore copper, a well-known transition metal, in this context.Copper is an essential trace element for the proper functioning of all living organisms, as well as a useful industrial material.
Copper has many applications, including electrical wiring, plumbing, and coinage. The element's atomic number is 29, and it is a transition metal with a full d-shell. Copper has a high electron density, which enables it to absorb a wide range of electromagnetic radiation, resulting in its distinct colors in various forms. Copper compounds have a wide range of colors, including blue, green, red, yellow, and brown, depending on the oxidation state and ligands present in the compound. Copper(I) compounds, such as cuprous oxide (Cu2O), have a red color, while copper(II) compounds, such as copper sulfate (CuSO4), are blue.
Copper (I) compounds, such as cuprous oxide (Cu2O), are red, while copper (II) compounds, such as copper sulfate (CuSO4), are blue. Copper compounds' color is the result of the splitting of the d-orbitals of copper atoms, which results from the absorption of visible light. Malachite and azurite, two copper-containing minerals, are popular gemstones that display bright colors due to copper's absorption of visible light. Copper's electron configuration and metallic character are linked to its coloration and its use in metallurgy, biology, and art.
To know more about transition metals visit:-
https://brainly.com/question/33019055
#SPJ11
please show steps.
differential equations
2. (7 points each) The following differential equation represents the motion of an object with mass m, the friction c, and the spring constant k in a spring-mass system with damping: my" + cy' + ky =
The given differential equation represents the motion of a spring-mass system with damping.
In a spring-mass system with damping, the object experiences three forces: the force due to the spring, the force due to damping, and the force due to inertia. The equation of motion for this system can be represented by the differential equation: my" + cy' + ky = 0, where m is the mass of the object, y is the displacement of the object from its equilibrium position, y' is the velocity of the object, y" is the acceleration of the object, c is the frictional damping coefficient, and k is the spring constant.
The term my" represents the force due to inertia, which is proportional to the mass of the object and its acceleration. The term cy' represents the force due to damping, which is proportional to the velocity of the object and the damping coefficient c. Finally, the term ky represents the force due to the spring, which is proportional to the displacement of the object and the spring constant k.
By setting the sum of these forces equal to zero, we obtain the differential equation that describes the motion of the spring-mass system with damping. Solving this differential equation will allow us to determine the position and velocity of the object as a function of time.
Learn more about equation
brainly.com/question/29538993
#SPJ11
Select the correct answer from each drop-down menu.
A cube shaped box has a side length of 15 inches and contains 27 identical cube shaped blocks. What is the surface area of all 27 blocks compared to
the surface area of the box?
inches, so the total surface area of the 27 blocks is
the surface area of the box
The side length of the blocks is
Reset
Next
square inches. This is
The surface area of all 27 blocks is 36,450 square inches, which is 27 times greater than the surface area of the box.
A cube-shaped box with a side length of 15 inches has a total surface area of [tex]6 \times (15^2) = 6 \times 225 = 1350[/tex] square inches.
Each block is identical in size and shape to the box, so each block also has a side length of 15 inches.
The total surface area of all 27 blocks can be calculated by multiplying the surface area of one block by the number of blocks.
Surface area of one block [tex]= 6 \times (15^2) = 6 \times225 = 1350[/tex] square inches.
Total surface area of 27 blocks = Surface area of one block[tex]\times 27 = 1350 \times 27 = 36,450[/tex] square inches.
Comparing the surface area of all 27 blocks to the surface area of the box:
Surface area of all 27 blocks:
Surface area of the box = 36,450 square inches : 1350 square inches.
For similar question on surface area.
https://brainly.com/question/951562
#SPJ8
Thermally isolated gas CH4 is slowly compressed to a 3.000 times smaller volume and then isothermally, decompressed back to the initial volume. What would be the gas temperature in degrees Celsius after compression and decompression if its initial temperature is 100.00°C and initial pressure is 2.00 atm? Use classical expression for the gas specific heat.
The gas in question is CH4, which is methane. It is initially thermally isolated, meaning there is no heat exchange with the surroundings.
First, the gas is slowly compressed to a volume 3.000 times smaller than its initial volume. During this compression, the gas is still thermally isolated, so there is no heat exchange.
Next, the gas is decompressed isothermally, meaning the temperature remains constant during this process. The gas is returned to its initial volume.
To find the final temperature after compression and decompression, we can use the formula for the specific heat capacity of an ideal gas:
Q = nCΔT
Where:
Q is the heat transferred to the gas (or from the gas),
n is the number of moles of the gas,
C is the molar specific heat capacity of the gas at constant volume,
ΔT is the change in temperature.
Since the gas is thermally isolated, no heat is transferred during the compression and decompression processes. Therefore, Q = 0.
Since the volume is reduced by a factor of 3.000 during compression, the pressure will increase by the same factor according to Boyle's Law:
P1V1 = P2V2
Where:
P1 is the initial pressure,
V1 is the initial volume,
P2 is the final pressure,
V2 is the final volume.
Plugging in the given values:
P1 = 2.00 atm
V1 = 1 (initial volume, arbitrary unit)
P2 = ?
V2 = 1/3 (final volume)
2.00 atm * 1 = P2 * 1/3
P2 = 6.00 atm
Now, we can use the ideal gas law to find the number of moles of the gas:
PV = nRT
Where:
P is the pressure,
V is the volume,
n is the number of moles,
R is the ideal gas constant (0.0821 L·atm/(mol·K)),
T is the temperature in Kelvin.
Plugging in the values:
P = 6.00 atm
V = 1 (initial volume, arbitrary unit)
n = ?
R = 0.0821 L·atm/(mol·K)
T = 100.00°C + 273.15 = 373.15 K (initial temperature in Kelvin)
6.00 atm * 1 = n * 0.0821 L·atm/(mol·K) * 373.15 K
n = 0.145 mol
Since the compression and decompression processes are reversible, the number of moles of the gas remains constant.
Now, we can find the final temperature after decompression using the ideal gas law again:
P = 2.00 atm (initial pressure)
V = 1 (initial volume, arbitrary unit)
n = 0.145 mol
R = 0.0821 L·atm/(mol·K)
T = ?
2.00 atm * 1 = 0.145 mol * 0.0821 L·atm/(mol·K) * T
T = 13.74 K
Converting the temperature to degrees Celsius:
T = 13.74 K - 273.15 = -259.41°C
Therefore, the gas temperature after compression and decompression would be approximately -259.41°C.
Know more about heat exchange:
https://brainly.com/question/13039682
#SPJ11
F(x)=3x-5 and g(x) = 2 to the power of 2 +2 find (f+g)(x)
The sum of f(x) and g(x) results in a new function (f+g)(x), where the coefficients of x .Therefore, (f+g)(x) is equal to 3x + 1.
d the constants are added together. In this case, the resulting function is 3x + 1.To find (f+g)(x), we need to add the functions f(x) and g(x) together.Given f(x) = 3x - 5 and g(x) = 2^2 + 2, we can substitute these expressions into the sum:
(f+g)(x) = f(x) + g(x)= (3x - 5) + (2^2 + 2)
= 3x - 5 + 4 + 2
= 3x + 1
For more such questions on sum
https://brainly.com/question/30432029
#SPJ8
Please help and show work please
Answer:
at least three sides it can have more if you look up polygons it will tell you that polygons have three sides or more of their shapes
Step-by-step explanation:
Apply Jacobi's method to the given system. Take the zero vector as the initial approximation and work with four-significant-digit accuracy until two successive iterates agree within 0. 001 in each variable. Compare your answer with the exact solution found using any direct method you like. (Round your answers to three decimal places. )
Once you provide the system of equations, we can proceed with the Jacobi's method as follows:
Write the system of equations in matrix form: Ax = b, where A is the coefficient matrix, x is the vector of unknowns, and b is the constant vector on the right-hand side. Decompose the coefficient matrix A into the sum of diagonal (D), lower triangular (L), and upper triangular (U) matrices: A = D - L - U.
Initialize the iteration by setting x^(0) as the zero vector. Iterate using the Jacobi method until the desired convergence criterion is met:
Calculate the next iterate using the formula: x^(k+1) = D^(-1)(b - (L + U)x^(k)).
Repeat this step until two successive iterates agree within the desired tolerance.
Compare the result obtained from Jacobi's method with the exact solution found using a direct method, such as Gaussian elimination or matrix inversion.
Please provide the system of equations so that I can assist you further with the calculations.
Learn more about Jacobi's here
https://brainly.com/question/30978173
#SPJ11
What is the answer for 1,2,3?
Answer:
1: A (Function)
2: B {(3,2), (2,1), (8,2), (5,7)}
3: C (Domain)
Step-by-step explanation:
Domains are the x values that go right or left.
Ranges are the y values that go up or down.
If the domain repeats when given a set of points, it is not a function.
The domain (x value) CAN'T repeat.
The weights of crates of apples are normally distributed with a mean of 26.4 pounds and a standard deviation of 3.1 pounds. If a particular crate of apples weighs 31.6 pounds, what is the percentile rank of its weight to the nearest whole percent? Show how you arrived at your answer.
Estimate the deflection of a simply supported prestressed concrete beam at the prestress transfer. The beam span is 12 m and has the rectangular cross-section of 200 (b) x 450 (h) mm. The unit weight of concrete is 25 kN/m³. The tendon is in a parabolic shape. The eccentricity at the mid-span and the two ends is 120 mm and 50 mm below the sectional centroid, respectively. The tendon force after transfer is 600 kN. At the prestress transfer state, the elastic modulus of concrete E-20 kN/mm².
Hint: The mid-span deflection due to UDL w is: y=- 5/384.WL^2/ El
The mid-span deflection due to constant moment Mis: y=- ML /8EI
The deflection of the simply supported prestressed concrete beam at the prestress transfer is approximately 11.68 mm. This estimation considers the deflection due to the UDL caused by the tendon force and the deflection due to the constant moment induced by the eccentricities at the mid-span and ends of the beam.
1. Calculation of the deflection due to the UDL (Uniformly Distributed Load):
Given:
Beam span (L): 12 m
Cross-section dimensions: 200 (b) x 450 (h) mm
Unit weight of concrete: 25 kN/m³
Tendon force after transfer: 600 kN
Eccentricity at mid-span: 120 mm (below centroid)
Eccentricity at ends: 50 mm (below centroid)
Elastic modulus of concrete (E): 20 kN/mm²
First, we need to calculate the total weight of the beam:
Weight = Cross-sectional area x Length x Unit weight
Weight = (0.2 m x 0.45 m) x 12 m x 25 kN/m³
Weight = 135 kN
The equivalent UDL (w) due to the tendon force can be calculated as follows:
w = Total tendon force / Beam span
w = 600 kN / 12 m
w = 50 kN/m
Using the formula for mid-span deflection due to UDL:
y = -5/384 * w * L^4 / (E * I)
Where:
L = Beam span = 12 m
E = Elastic modulus of concrete = 20 kN/mm²
I = Moment of inertia of the rectangular section = (b * h^3) / 12
Substituting the values:
I = (0.2 m * (0.45 m)^3) / 12
I = 0.0028125 m^4
y = -5/384 * 50 kN/m * (12 m)^4 / (20 kN/mm² * 0.0028125 m^4)
y ≈ 9.84 mm
2. Calculation of the deflection due to the constant moment:
Given:
Eccentricity at mid-span: 120 mm
Eccentricity at ends: 50 mm
The maximum moment (M) at the mid-span due to prestress can be calculated as:
M = Tendon force * Eccentricity at mid-span
M = 600 kN * 0.120 m
M = 72 kNm
Using the formula for mid-span deflection due to constant moment:
y = -M * L / (8 * E * I)
Substituting the values:
y = -72 kNm * 12 m / (8 * 20 kN/mm² * 0.0028125 m^4)
y ≈ 1.84 mm
3. Total deflection at the prestress transfer:
Total deflection = Deflection due to UDL + Deflection due to constant moment
Total deflection ≈ 9.84 mm + 1.84 mm
Total deflection ≈ 11.68 mm
Learn more about prestress transfer visit:
https://brainly.com/question/31504504
#SPJ11
It has been suggested that the triplet genetic code evolved from a two-nucleotide code. Perhaps there were fewer amino acids in the ancient proteins. Comment on the features of the genetic code that might support this hypothesis? 2.The strands of DNA can be separated by heating the DNA sample. The input heat energy breaks the hydrogen bonds between base pairs, allowing the strands to separate from one another. Suppose that you are given two DNA samples. One has a G + C content of 70% and the other has a G + C content of 45%. Which of these samples will require a higher temperature to separate the strands? Explain your answer.
The features of the genetic code that support the hypothesis of the triplet genetic code evolving from a two-nucleotide code are the degeneracy and universality of the genetic code.
The genetic code is degenerate, meaning that multiple codons can code for the same amino acid. For example, the amino acid leucine is coded by six different codons. This suggests that the genetic code could have started with fewer amino acids, and as more amino acids evolved, the code expanded to accommodate them. Additionally, the genetic code is universal, meaning that it is shared by almost all organisms on Earth. This universality suggests that the genetic code has ancient origins and has been conserved throughout evolution. These features of the genetic code support the hypothesis that it evolved from a simpler, two-nucleotide code with fewer amino acids.
In summary, the degeneracy and universality of the genetic code provide evidence to support the hypothesis that the triplet genetic code evolved from a two-nucleotide code with fewer amino acids. The degeneracy of the code suggests that it could have expanded to accommodate more amino acids over time, while the universality of the code implies ancient origins and conservation throughout evolution.
Know more about genetic code here:
https://brainly.com/question/17306054
#SPJ11
please double check your work
Given f(8) 14 at f'(8) = 2 approximate f(8.3). f(8.3)~ =
The approximate value of f(8.3) is 14.6, obtained using the linear approximation formula with given values for f(a), f'(a), and x.
To find the approximation, we use the formula f(x) ≈ f(a) + f'(a) * (x - a), where a = 8, f(a) = 14, f'(8) = 2, and x = 8.3.
Substituting these values, we calculate f(8.3) ≈ 14 + 2 * (8.3 - 8) ≈ 14 + 2 * 0.3 ≈ 14 + 0.6 ≈ 14.6.
This linear approximation provides an estimate of f(8.3) based on the given information and the behavior of the function near the point a.
To further understand the concept of linear approximation, it is important to recognize that it is based on the idea of using a linear function to approximate a more complex function near a specific point. The formula f(x) ≈ f(a) + f'(a) * (x - a) represents the equation of a tangent line to the graph of the function f(x) at the point (a, f(a)).
The linear approximation provides a reasonable estimate of the function's value for values of x that are close to the point a.
In this particular case, we are given the function f(x) and its derivative f'(x) evaluated at a = 8. By using the linear approximation formula and substituting the values, we obtain an approximation for f(8.3).
It's important to note that the accuracy of the approximation depends on how closely the function behaves linearly near the point a.
If the function has significant curvature or nonlinearity in the vicinity of a, the approximation may not be as accurate.
To learn more about function click here
brainly.com/question/30721594
#SPJ11
Two bacteria cultures are being studied in a lab. At the start,
bacteria A had a population of 60 bacteria and the number of
bacteria was tripling every 8 days. Bacteria B had a population of
30 bacte
At the start, bacteria A had a population of 60 bacteria and the number of bacteria was tripling every 8 days. Bacteria B had a population of 30 bacteria, but the question seems to be cut off before providing any information about the growth rate or pattern for Bacteria B.
For Bacteria A, we know that the population starts at 60 bacteria. Since it is tripling every 8 days, we can calculate the population at different time points by multiplying the initial population by the growth factor.
After 8 days, the population would be 60 * 3 = 180 bacteria.
After 16 days, the population would be 180 * 3 = 540 bacteria.
After 24 days, the population would be 540 * 3 = 1620 bacteria.
And so on.
Each time, we multiply the previous population by 3 to get the new population after 8 days.
As for Bacteria B, since no information is given about its growth rate or pattern, we cannot determine its population at different time points. It is important to have this information in order to calculate the population accurately.
population of 60 bacteria and tripling every 8 days : https://brainly.com/question/3222533
#SPJ11
HELP PLSS
This assignment is past the original due date of Sun 04/24/2022 11:59 pm. You were granted an extension Due Tue 05/17/2022 11:59 p Find the consumer's and producer's surplus if for a product D(x) = 25
To find the consumer's and producer's surplus, we need more information about the demand and supply functions or the market equilibrium.
You provided the demand function D(x) = 25, but we require additional details to proceed with the calculations. The consumer's surplus is the difference between the maximum price consumers are willing to pay and the price they actually pay. It represents the benefit or surplus gained by consumers in a market transaction.
The producer's surplus is the difference between the minimum price producers are willing to accept and the price they actually receive. It represents the benefit or surplus gained by producers in a market transaction.
To calculate these surpluses, we typically need information about the supply function, equilibrium price, and equilibrium quantity. These values help determine the areas of the consumer's and producer's surpluses on the supply-demand graph.
Please provide the necessary information about the supply function, equilibrium price, or any other relevant details so that I can assist you in calculating the consumer's and producer's surplus accurately.
Learn more about equilibrium here
https://brainly.com/question/24735820
#SPJ11
A 90 wt.% Ag-10 wt.% Cu alloy is heated to a temperature within the B + liquid phase region. If the composition of the liquid phase is 85 wt% Ag, determine: (a) The temperature of the alloy. (b) The composition of the B phase. (c) The mass fractions of both phases.
To determine the temperature, composition of the B phase, and mass fractions of both phases in the given alloy, we need to refer to the phase diagram for the Ag-Cu system. Without the specific phase diagram, I can provide a general explanation of how to approach this problem.
(a) The temperature of the alloy:
On the phase diagram, locate the composition of the alloy (90 wt.% Ag-10 wt.% Cu).
(b) The composition of the B phase:
Once you have determined the temperature of the alloy, trace a horizontal line from this temperature to the B phase region.
(c) The mass fractions of both phases:
To calculate the mass fractions of both phases, you need to use the lever rule.
Measure the lengths of the tie line and the B phase region. The mass fraction of the liquid phase can be calculated as:
Mass fraction of liquid phase = Length of tie line / Total length of the region in which the phases coexist.
Similarly, the mass fraction of the B phase can be calculated as:
Mass fraction of B phase = Length of B phase region / Total length of the region in which the phases coexist.
Explanation:
Please note that the specific values required for the calculations, such as the lengths of the tie line and the regions, can only be determined from the phase diagram for the Ag-Cu system. I recommend referring to a reliable phase diagram or materials science resources to obtain accurate values for the calculations.
To know more about temperature visit:
https://brainly.com/question/7510619
#SPJ11
Derive the following design equations starting from the general mole balance equation a) CSTR b) Batch c) PBR [7] [7] [6] 12 Marks Question 2 a) Describe the three ways in which a chemical species can lose its identity and give an example for each. [6] b) With the aid of a sketch illustrate the rate of reaction in relation to reagents and products.
The concentration of reactants decreases, and the concentration of products increases as the reaction progresses. The reaction rate increases as the concentration of reactants decreases.
Design equations for different reactor types: CSTR: Consider a well-mixed reactor where the contents of the reactor are instantly and thoroughly mixed, and where the outlet stream has the same composition as that in the reactor.
Consider a continuous flow of fluid entering the reactor and leaving the reactor at the same rate. The rate of accumulation of the chemical in the tank equals the rate of flow in minus the rate of flow out. The volume of the reactor is constant since the reactor is a well-mixed continuous flow reactor, and thus the reactor is of constant volume.
Batch: A batch reactor is a vessel that holds reactants for an extended period of time. It is a sealed system that can be operated in a range of temperature and pressure conditions. In batch processes, the process cycle is repeated to achieve the required product output. In a batch reactor, the energy required for a reaction is supplied as heat via the jacket.
PBR: A plug flow reactor (PFR) or continuous tubular reactor (CTR) is an open system that has a fixed flow rate. It has no internal mixing, and the concentration of the fluid varies along the length of the reactor. Because the reactants enter and leave the reactor continuously, the volume of the fluid within the reactor is constant. The reaction rate of a plug flow reactor is dependent on the amount of time the reactants spend within the reactor. Description of the three ways in which a chemical species can lose its identity and give an example for each:
The three ways in which a chemical species can lose its identity are:
1. Chemical Reactions: This is the most common method for a chemical species to lose its identity. When a substance reacts chemically with another substance to form a new product, this occurs. For example, when magnesium reacts with hydrochloric acid, it produces magnesium chloride and hydrogen gas.
2. Radioactive decay: This is the process by which a substance loses its identity as a result of radioactive decay. When the nucleus of an atom is unstable, it may spontaneously emit radiation and change into a different element. For example, when radium decays, it becomes radon.
3. Photolysis: This is the process by which a substance loses its identity as a result of exposure to light. When a substance is exposed to light, it may decompose into its constituent parts.
For example, when chlorine gas is exposed to ultraviolet light, it decomposes into chlorine atoms. Sketch illustrating the rate of reaction in relation to reagents and products: The rate of reaction is the amount of product formed or reactant consumed per unit time. The reaction rate is dependent on the concentration of the reactants, temperature, catalyst, surface area, and other factors. The graph illustrates the relationship between the concentration of reactants and products and the reaction rate. The concentration of reactants decreases, and the concentration of products increases as the reaction progresses. The reaction rate increases as the concentration of reactants decreases.
Learn more about batch reactor visit:
brainly.com/question/33227944
#SPJ11
310. mg of an unknown protein are dissolved in enough solvent to make 5.00mb of solution. The osmoce pressure of this solution is meakired to be 0.303 atm at 25.0%C Calculate the malar mass of the protein. Round your answer to 3 signficant digits.
The molar mass of the protein is approximately 50,800 g/mol.
To calculate the molar mass of the protein, we can use the osmotic pressure and the concentration of the protein solution.
Mass of protein = 310 mg = 0.310 g
Volume of solution = 5.00 mL = 5.00 x 10^(-3) L
Osmotic pressure = 0.303 atm
Temperature = 25.0°C = 298.15 K
We can use the formula for osmotic pressure:
π = MRT
Where:
π = osmotic pressure
M = molarity of the solution (mol/L)
R = ideal gas constant (0.0821 L·atm/(mol·K))
T = temperature in Kelvin
Rearranging the equation, we can solve for molarity (M):
M = π / (RT)
Now we can calculate the molarity of the protein solution:
M = 0.303 atm / (0.0821 L·atm/(mol·K) * 298.15 K)
M ≈ 0.0122 mol/L
The molarity (M) is defined as moles per liter (mol/L). To find the molar mass of the protein, we can rearrange the equation to:
Molar mass = mass of protein / moles of protein
Molar mass = 0.310 g / (0.0122 mol/L * 5.00 x 10^(-3) L)
Molar mass ≈ 50814 g/mol
Rounded to 3 significant digits, the molar mass of the protein is approximately 50,800 g/mol.
Learn more about Osmotic pressure
brainly.com/question/32903149
#SPJ11
Q6. Find TG for all the words with even number of a's and even number of b's then find its regular expression by using Kleene's theorem.Q6. Find TG for all the words with even number of a's and even number of b's then find its regular expression by using Kleene's theorem.
To find the Transition Graph (TG) for the language of all words with an even number of 'a's and an even number of 'b's, we can follow these steps:
Step 1: Define the alphabet:
Let the alphabet Σ be {a, b}.
Step 2: Define the states:
We need states to keep track of the parity (even or odd) of 'a's and 'b's encountered so far. Let's define the states as follows:
State A: Even number of 'a's, even number of 'b's
State B: Odd number of 'a's, even number of 'b's
State C: Even number of 'a's, odd number of 'b's
State D: Odd number of 'a's, odd number of 'b's
Step 3: Define the transitions:
For each state and input symbol, we determine the next state. The transitions are as follows:
From state A:
On input 'a': Transition to state B
On input 'b': Transition to state C
From state B:
On input 'a': Transition to state A
On input 'b': Transition to state D
From state C:
On input 'a': Transition to state D
On input 'b': Transition to state A
From state D:
On input 'a': Transition to state C
On input 'b': Transition to state B
Step 4: Determine the initial state and accepting state(s):
Initial state: State A
Accepting state: State A
Step 5: Draw the Transition Graph:
css
a b
(A) -----> (B) -----> (D)
| ^ ^
| | |
| b | a | a
v | |
(C) <----- (A) <----- (D)
| b ^ ^
| | |
| | a | b
v | |
(D) -----> (C) -----> (B)
| ^ ^
| | |
| a | b | b
v | |
(A) <----- (C) <----- (A)
Now, let's find the regular expression using Kleene's theorem. We can apply the algorithm to obtain a regular expression from the Transition Graph.
Step 1: Assign variables to each state:
State A: A
State B: B
State C: C
State D: D
Step 2: Write the equations for each state transition:
A = aB + bC
B = aA + bD
C = aD + bA
D = aC + bB
Step 3: Solve the equations to eliminate the variables:
Substituting the equations into each other, we get:
A = a(aA + bD) + b(aD + bA)
Simplifying the equation:
A = aaA + abD + abD + bbA
A - aaA - bbA = 2abD
A(1 - aa - bb) = 2abD
A = 2abD / (1 - aa - bb)
Similarly, we can solve for the other variables:
B = aA + bD = a(2abD / (1 - aa - bb)) + bD
C = aD + bA = aD + b(2abD / (1 - aa - bb))
D = aC + bB = a(2abD / (1 - aa - bb)) + b(aA + bD)
Step 4: Simplify the equations:
A = 2abD / (1 - aa - bb)
B = 2a²b²D / (1 - aa - bb) + bD
C = 2a²b²D / (1 - aa - bb) + b²(2abD / (1 - aa - bb))
D = a²(2abD / (1 - aa - bb)) + b²D
Step 5: Substitute the equations into each other to eliminate the variable D:
A = 2ab(a²(2abD / (1 - aa - bb)) + b²D) / (1 - aa - bb)
Simplifying the equation:
A(1 - aa - bb) = 4a⁴b³D + 4a³b³D + 2a²bD + 2ab²D
A - 4a⁴b³D - 4a³b³D - 2a²bD - 2ab²D = 0
A - 4a³b³D - 4a²b²D - 2abD(a + b) = 0
Factoring out D:
A - D(4a³b³ + 4a²b² + 2ab(a + b)) = 0
D = A / (4a³b³ + 4a²b² + 2ab(a + b))
Using similar substitutions, we can solve for the other variables.
Therefore, the regular expression for the language of all words with an even number of 'a's and an even number of 'b's is:
A / (4a³b³ + 4a²b² + 2ab(a + b))
Learn more about Transition Graph here:
https://brainly.com/question/29261894
#SPJ11
A cantilever beam (that is one end is fixed and the other end free), carries a uniform load of 4kN/m throughout its entire length of 3 m. The beam has a rectangular shape 100 mm wide and 200 mm high. Find the maximum bending stress developed at a section 2 m from the free end of the beam.
subjected to a uniform load of 4 kN/m, with rectangular dimensions of 100 mm width and 200 mm height, can be determined as X MPa.
Calculate the bending moment (M) at the section 2 m from the free end of the beam using the formula M = (w * L^2) / 2, where w is the uniform load (4 kN/m) and L is the distance from the fixed end (2 m).
Determine the section modulus (Z) of the rectangular beam using the formula Z = (b * h^2) / 6, where b is the width (100 mm) and h is the height (200 mm).
Compute the maximum bending stress (σ) using the formula σ = (M * c) / Z, where M is the bending moment, c is the distance from the neutral axis (which is half the height of the beam), and Z is the section modulus.
Plug in the calculated values to find the maximum bending stress at the specified section of the beam.
To know more about uniform load visit:
https://brainly.com/question/33588962
#SPJ11
Give the electron configuration for the following (must do all 3): a. Te b. Cr c. Zn²+ Select all of the following that canNOT exceed the octet rule OP Kr C F
a. The electron configuration for the element Te is 1s²2s²2p⁶3s²3p⁶4s²3d¹⁰4p⁶5s²4d¹⁰5p⁴.b. The electron configuration for the element Cr is 1s²2s²2p⁶3s²3p⁶3d⁵4s¹.c. The electron configuration for the ion Zn²⁺ is 1s²2s²2p⁶3s²3p⁶3d¹⁰.
Te: 1s²2s²2p⁶3s²3p⁶4s²3d¹⁰4p⁶5s²4d¹⁰5p⁴Cr: 1s²2s²2p⁶3s²3p⁶3d⁵4s¹Zn²⁺: 1s²2s²2p⁶3s²3p⁶3d¹⁰.
This question is divided into three parts where the electron configurations of three elements are asked.
The electron configuration of the first element which is Te is 1s²2s²2p⁶3s²3p⁶4s²3d¹⁰4p⁶5s²4d¹⁰5p⁴.
The electron configuration of the second element which is Cr is 1s²2s²2p⁶3s²3p⁶3d⁵4s¹ and the electron configuration of the third element which is Zn²⁺ is 1s²2s²2p⁶3s²3p⁶3d¹⁰.
Only F canNOT exceed the octet rule.
To know more about octet rule :
brainly.com/question/33717924
#SPJ11
As the molar masses of molecular substances increase, generally their boiling points and vapor pressures (A) decrease, decrease (B) increase, decrease (C) decrease, increase (D) increase, increase At
As the molar masses of molecular substances increase, their boiling points generally increase due to stronger intermolecular forces, while their vapor pressures generally decrease due to slower molecular motion. Therefore, the answer to the given question is (C) decrease, increase.
As the molar masses of molecular substances increase, generally their boiling points and vapor pressures decrease.
The boiling point of a substance is the temperature at which it changes from a liquid to a gas. It is influenced by intermolecular forces, which are the attractive forces between molecules. As the molar mass of a molecular substance increases, the intermolecular forces generally become stronger. This is because larger molecules have more electrons and a greater surface area, which allows for stronger attractive forces between molecules. Stronger intermolecular forces require more energy to overcome, leading to a higher boiling point. So, as the molar masses of molecular substances increase, their boiling points tend to increase.
On the other hand, vapor pressure is the pressure exerted by the gas molecules when a substance is in equilibrium between its liquid and gaseous phases. It is affected by the ease with which molecules can escape from the liquid phase into the gas phase. As the molar mass of a molecular substance increases, the average speed of its molecules generally decreases. This is because larger molecules have more mass, making it harder for them to move and escape from the liquid phase. As a result, the vapor pressure of a substance decreases as its molar mass increases.
To summarize, as the molar masses of molecular substances increase, their boiling points generally increase due to stronger intermolecular forces, while their vapor pressures generally decrease due to slower molecular motion. Therefore, the answer to the given question is (C) decrease, increase.
Learn more about molecular on :
https://brainly.com/question/475709
#SPJ11
Which statement describes the solutions of this equation? 2/x+2 + 1/10 = 3/x + 3
The statement that describes the solution of the equation is:
Option A: The equation has two valid solutions and no extraneous solution
How to find the solution of the equation?The equation we want to solve is given as:
[tex]\frac{2}{x + 2} + \frac{1}{10} = \frac{3}{x + 3}[/tex]
Multiply through by 10(x + 2)(x + 3) to get:
20(x + 3) + (x + 2)(x + 3) = 30(x + 2)
Expanding gives:
20x + 60 + x² + 5x + 6 = 30x + 60
x² - 5x + 6 = 0
Using quadratic equation calculator gives:
x = 2 or x = 3
Thus, the equation has two valid solutions and no extraneous solution
Read more about Equation Solution at: https://brainly.com/question/20087071
#SPJ1
A horizontal circular cavity with a diameter of 2R,=6m is excavated in the rock mass at a depth of 400m below the surface. It is assumed that the natural stress of the rock mass is hydrostatic pressure state, and the natural density of the rock mass is p=2.7g/cm'. Please calculate: (1) The redistributed stress on the wall and 2 times of the radius of the cavity (2) If the strength parameters of the surrounding rock are Cm = 0.4MPa, m = 30°, please discuss the stability of the cavity (3) If the cavity is not stable, please calculate the radius of the plastic ring (R1) = >
The radius of the plastic ring (R1) is approximately 0.993 meters.
In summary, the redistributed stress on
(1) To calculate the redistributed stress on the wall at 2 times the radius of the cavity, we need to consider the vertical and horizontal stress components. Since the natural stress of the rock mass is in a hydrostatic pressure state, the vertical stress at a depth of 400m can be calculated using the formula:
σv = γz
where γ is the unit weight of the rock mass and z is the depth. Given that the natural density of the rock mass is 2.7 g/cm³, we can convert it to kg/m³ by dividing by 1000:
γ = 2.7 g/cm³ ÷ 1000 kg/m³ = 0.0027 kg/cm³
Now, we can calculate the vertical stress:
σv = 0.0027 kg/cm³ * 400 m = 1.08 kg/cm²
To determine the horizontal stress, we can use the empirical formula for hydrostatic stress conditions:
σh = Kσv
where K is the coefficient of lateral earth pressure. For rock masses, K is typically around 0.8. Applying this value, we find:
σh = 0.8 * 1.08 kg/cm² = 0.864 kg/cm²
Finally, to calculate the redistributed stress on the wall at 2 times the radius of the cavity, we need to add the horizontal stress to the vertical stress at that location:
Redistributed stress = σv + σh = 1.08 kg/cm² + 0.864 kg/cm² = 1.944 kg/cm²
(2) To assess the stability of the cavity, we can calculate the shear strength of the surrounding rock using the strength parameters provided. The shear strength is given by the equation:
τ = C + σn * tan(m)
where C is the cohesion and m is the friction angle. Given Cm = 0.4 MPa and m = 30°, we can substitute these values:
τ = 0.4 MPa + σn * tan(30°)
Now, we need to determine the normal stress on the cavity wall. At a depth of 400m, the vertical stress is the same as the calculated σv from part (1):
σn = σv = 1.08 kg/cm²
Substituting this value and calculating:
τ = 0.4 MPa + 1.08 kg/cm² * tan(30°)
τ ≈ 0.4 MPa + 0.622 kg/cm² ≈ 1.022 MPa
The redistributed stress on the wall at 2 times the radius of the cavity is 1.944 kg/cm², which is greater than the shear strength of the surrounding rock, 1.022 MPa. This indicates that the cavity is not stable and is likely to experience failure.
(3) If the cavity is not stable, we can calculate the radius of the plastic ring (R1) using the equation:
R1 = R * (σv / τ)^0.5
where R is the radius of the cavity and σv is the vertical stress. Substituting the values:
R1 = 3 m * (1.08 kg/cm² / 1.022 MPa)^0.5
Converting units to be consistent:
R1 ≈ 3 m * (1.08 kg/cm² / 10.22 kg/cm²)^0.5
R1 ≈ 3 m * 0.331
R1 ≈ 0.993 m
Therefore, the radius of the plastic ring (R1) is approximately 0.993 meters.
In summary, the redistributed stress on
Learn more about radius
https://brainly.com/question/27696929
#SPJ11
Flexible electronics is becoming an increasingly popular research topic due to their exciting potential applications such as artificial skin. You land a job at FlexSkin, a new startup company in Bethlehem trying to develop electrically conductive skin- like materials for prosthetics. Their newest material prototype (called CarboFlex) is synthesized by imbedding carbon nano-fibers (CNFs) as both a highly conductive and reinforcing phase into thin films of poly-methyl-meth-acrylate (PMMA). FlexSkin claims that CarboFlex can maintain its conductive properties under temperature conditions ranging from -100 °C to 100 °C. You are suspicious since this claim is made based on separate mechanical and electrical tests! Hence, you decide to run a stress-condition-simulating dynamic bending test of the PMMA-CNF composite while concurrently measuring its electrical properties. At freezing temperatures, the composite indeed behaves as claimed but as you approach 100 °C the conductivity begins to drop rapidly as a function of number of bending cycles. Your boss sees the data, freaks out and asks for an immediate explanation. How can you explain the high temperature-induced conductive property breakdown?
As the dynamic bending test is performed, the composite's temperature stress is applied, and the difference in thermal expansion coefficients between CNFs and PMMA plays a significant role in the conductive properties' breakdown.
As the temperature approaches 100 °C, the conductivity of the PMMA-CNF composite begins to drop rapidly as a function of the number of bending cycles. In this dynamic bending test, temperature stress is applied, which affects the conductivity of the material. This effect is due to two factors.
Firstly, carbon nanofibers and PMMA have different thermal expansion coefficients, which leads to differential thermal expansion when exposed to different temperatures.
Secondly, PMMA has a glass transition temperature (Tg) of approximately 100 °C, which is close to the highest temperature at which the composite can maintain its conductivity. The composite material that Flex.
Skin is using for their Carbo
Flex product contains carbon nano-fibers (CNFs) embedded in poly-methyl-meth-acrylate (PMMA) thin films, which is highly conductive and can maintain its conductive properties under temperatures from -100 °C to 100 °C.
Learn more about carbon:
https://brainly.com/question/13046593
#SPJ11
For each of the following functions, determine all complex numbers for which the function is holomorphic. If you run into a logarithm, use the principal value unless otherwise stated.
(d) exp(zˉ)
The function f(z) = exp(z-bar) is holomorphic for all complex numbers z, because the derivative of exp(z-bar) exists and is continuous for all complex numbers.
(d)
To understand why this is the case, let's break down the function. The function exp(z) is the exponential function, which is defined for all complex numbers.
It takes a complex number z as input and outputs another complex number. The z-bar notation represents the complex conjugate of z, which means that the imaginary part of z is negated. Since both exp(z) and z-bar are defined for all complex numbers, the composition of these two functions, exp(z-bar), is also defined for all complex numbers.
A function is holomorphic if it is complex differentiable, meaning that its derivative exists and is continuous in a given domain. The derivative of exp(z-bar) can be computed using the chain rule.
The derivative of exp(z) with respect to z is exp(z), and the derivative of z-bar with respect to z is 0, since the conjugate of a complex number does not depend on z. Therefore, the derivative of exp(z-bar) with respect to z is also exp(z-bar).
Since the derivative of exp(z-bar) exists and is continuous for all complex numbers, we can conclude that exp(z-bar) is holomorphic for all complex numbers. In summary, the function f(z) = exp(z-bar) is holomorphic for all complex numbers.
To know more about complex number:
https://brainly.com/question/10662770
#SPJ11
If the equation y = (2-6) (z+12) is graphed in the coordinate plane, what are the x-intercepts of the resulting parabola?
Answer: (_,0) and (_,0)
The x-intercepts of the resulting parabola are (6, 0) and (-12, 0).
To find the x-intercepts of a parabola, we need to determine the values of x when y is equal to zero. In the given equation, y = (2-6)(z+12), we have y set to zero.
Setting y to zero:
0 = (2-6)(z+12)
Simplifying the equation:
0 = -4(z+12)
To solve for z, we divide both sides of the equation by -4:
0 / -4 = (z+12)
0 = z + 12
Subtracting 12 from both sides:
z = -12
So, one x-intercept of the parabola is (-12, 0).
To find the second x-intercept, we can substitute a different value for z. Let's substitute z = 6 into the equation:
0 = -4(6+12)
0 = -4(18)
0 = -72
Since the equation evaluates to zero, z = 6 is another x-intercept of the parabola.
Therefore, the x-intercepts of the resulting parabola are (6, 0) and (-12, 0).
For more such questions on parabola, click on:
https://brainly.com/question/29635857
#SPJ8
Question 3. In a falling-head permeability test the initial head of 2.00m dropped to 0.40 m in 3h, the diameter of the standpipe being 5mm. The soil specimen was 200 mm long by 100mm in diameter. Calculate the coefficient of permeability of the soil.
The coefficient of permeability of the soil is approximately 0.203 m/s.
To calculate the coefficient of permeability (k) of the soil using the falling-head permeability test, we can use Darcy's Law:
Q = (k * A * Δh) / (L * Δt)
Where:
Q is the discharge rate of water through the soil specimen,
k is the coefficient of permeability,
A is the cross-sectional area of the soil specimen,
Δh is the change in head,
L is the length of the soil specimen, and
Δt is the time it takes for the head to drop.
Let's calculate the values step by step:
1. Calculate the cross-sectional area (A) of the soil specimen:
A = π × (diameter/2)²
A = π × (100 mm/2)²
A = 3.14159 × (50 mm)²
A = 3.14159 × 2500 mm²
A = 7853.98 mm²
2. Convert the cross-sectional area to square meters:
A = 7853.98 mm²/(100 mm/2)²
A = 7,85398 m²
3. Calculate the change in head (Δh):
Δh = initial head - final head
= 2.00 m - 0.40 m
= 1.60 m
4. Convert the diameter of the standpipe to meters:
diameter = 5 mm / 1000
= 0.005 m
5. Calculate the discharge rate (Q):
Q = (k * A * Δh) / (L * Δt)
Since the falling-head permeability test involves a constant head, the discharge rate (Q) can be simplified as follows:
Q = (k * A) / Δt
We need to calculate Δt first.
6. Convert the time (3 hours) to seconds:
Δt = 3 hours * 60 minutes/hour * 60 seconds/minute
= 3 * 60 * 60 seconds
= 10,800 seconds
Now we can calculate Q:
Q = (k * A) / Δt
[tex]Q = (k * 7.85398 m^2) / 10,800 s[/tex]
We can rearrange the equation to solve for k:
k = (Q * Δt) / A
Now we need to calculate Q:
Q = (1.60 m) / (10,800 s)
= 0.0001481 m/s
Finally, substitute the values into the equation to calculate the coefficient of permeability (k):
k = (0.0001481 m/s * 10,800 s) / 7.85398 m²
≈ 0.203 m/s
Therefore, the coefficient of permeability of the soil is approximately 0.203 m/s.
To know more about Darcy's Law visit:
https://brainly.com/question/33970515
#SPJ11
In a falling-head permeability test the initial head of 2.00m dropped to 0.40 m in 3h, the diameter of the standpipe being 5mm. The soil specimen was 200 mm long by 100mm in diameter. The coefficient of permeability of the soil is approximately 0.203 m/s.
To calculate the coefficient of permeability (k) of the soil using the falling-head permeability test, we can use Darcy's Law:
Q = (k * A * Δh) / (L * Δt)
Where:
Q is the discharge rate of water through the soil specimen,
k is the coefficient of permeability,
A is the cross-sectional area of the soil specimen,
Δh is the change in head,
L is the length of the soil specimen, and
Δt is the time it takes for the head to drop.
Let's calculate the values step by step:
1. Calculate the cross-sectional area (A) of the soil specimen:
A = π × (diameter/2)²
A = π × (100 mm/2)²
A = 3.14159 × (50 mm)²
A = 3.14159 × 2500 mm²
A = 7853.98 mm²
2. Convert the cross-sectional area to square meters:
A = 7853.98 mm²/(100 mm/2)²
A = 7,85398 m²
3. Calculate the change in head (Δh):
Δh = initial head - final head
= 2.00 m - 0.40 m
= 1.60 m
4. Convert the diameter of the standpipe to meters:
diameter = 5 mm / 1000
= 0.005 m
5. Calculate the discharge rate (Q):
Q = (k * A * Δh) / (L * Δt)
Since the falling-head permeability test involves a constant head, the discharge rate (Q) can be simplified as follows:
Q = (k * A) / Δt
We need to calculate Δt first.
6. Convert the time (3 hours) to seconds:
Δt = 3 hours * 60 minutes/hour * 60 seconds/minute
= 3 * 60 * 60 seconds
= 10,800 seconds
Now we can calculate Q:
Q = (k * A) / Δt
We can rearrange the equation to solve for k:
k = (Q * Δt) / A
Now we need to calculate Q:
Q = (1.60 m) / (10,800 s)
= 0.0001481 m/s
Finally, substitute the values into the equation to calculate the coefficient of permeability (k):
k = (0.0001481 m/s * 10,800 s) / 7.85398 m²
≈ 0.203 m/s
Therefore, the coefficient of permeability of the soil is approximately 0.203 m/s.
To know more about coefficient visit:
https://brainly.com/question/13431100
#SPJ11
The vector ⇀r⇀= ⟨2, 3⟩ is multiplied by the scalar –4. Which statements about the components, magnitude, and direction of the scalar product –4⇀r⇀ are true? Select all that apply.
A. The component form of −4⇀−4r⇀is ⟨–8, –12⟩.
B. The magnitude of −4⇀−4r⇀is 4 times the magnitude of ⇀r⇀.
C. The direction of −4⇀−4r⇀ is the same as the direction of ⇀r⇀.
D. The vector −4⇀−4r⇀ is in the fourth quadrant.
E. The direction of −4⇀−4r⇀is 180° greater than the inverse tangent of its components.
The correct statements about the components, magnitude, and direction of the scalar product -4⇀r⇀ are:
A. The component form of -4⇀r⇀ is ⟨-8, -12⟩. When a vector is multiplied by a scalar, each component of the vector is multiplied by the scalar.
B. The magnitude of -4⇀r⇀ is 4 times the magnitude of ⇀r⇀. When a vector is multiplied by a scalar, the magnitude of the resulting vector is equal to the absolute value of the scalar multiplied by the magnitude of the original vector.
C. The direction of -4⇀r⇀ is the same as the direction of ⇀r⇀. Multiplying a vector by a scalar does not change its direction, only its magnitude.
D. The vector -4⇀r⇀ is not necessarily in the fourth quadrant. The quadrant of a vector depends on the signs of its components, and multiplying a vector by a negative scalar can change the signs of its components.
E. The direction of -4⇀r⇀ is not necessarily 180° greater than the inverse tangent of its components. The direction of a vector is given by the arctan(y/x), where (x, y) are the components of the vector. Multiplying the vector by a scalar does not affect its direction in this way.
Therefore, the correct statements are A, B, and C.
For such more question on magnitude
https://brainly.com/question/30337362
#SPJ8
A fermentation broth containing microbial cells is filtered through a vacuum filter. The broth is fed to the filter at a rate of 100 kg/h, which contains 4%(w/w) cell solids. In order to increase the performance of the process, filter aids are introduced at a rate of 12 kg/h. The concentration of vitamin in the broth is 0.09% by weight. Liquid filtrate is collected at a rate of 94 kg/h; the concentration of vitamin in the filtrate is 0.042%(w/w). Filter cake containing cells and filter aid is removed continuously from the filter cloth. (a) What percentage water is the filter cake? (b) If the concentration of vitamin dissolved in the liquid within the filter cake is the same as that in the filtrate, how much vitamin is absorbed per kg filter aid?
(a) The filter cake contains 4700% water.
(b) The amount of vitamin absorbed per kg filter aid is 0.0042 kg.
(a) The number of solids in the feed, w = 4%.
Mass of feed introduced per hour = 100 kg/h.
Amount of solids fed per hour = 4/100 * 100 = 4 kg solids/h.
The feed contains 4 kg solids and the remaining part is water.
Weight of water in the feed = 100 - 4 = 96 kg/h.
Weight of filter cake produced = Mass of feed - a mass of filtrate
96 - 94 = 2 kg/h.
Water content in the cake = (Weight of water in the cake/Weight of cake) * 100%=(94/2)*100% = 4700%
(b)
The total amount of vitamin in the feed = 0.09% by weight.
Weight of vitamin in feed per hour = 0.09/100 * 100 = 0.09 kg/h.
The filtrate concentration = 0.042%.
The rate of production of the filter cake = 12 kg/h.
Mass of vitamin in the filtrate per hour = 0.042/100 * 94
= 0.03948 kg/h.
Mass of vitamin in the filter cake per hour = 0.09 - 0.03948
= 0.05052 kg/h.0.05052 kg of vitamin is absorbed by 12 kg of filter aid.
The amount of vitamin absorbed by 1 kg filter aid = 0.05052/12
= 0.0042 kg (4.2 g) of vitamin is absorbed per kg filter aid.
Answer: (a) The filter cake contains 4700% water.
(b) The amount of vitamin absorbed per kg filter aid is 0.0042 kg.
Know more about vitamin here:
https://brainly.com/question/9348916
#SPJ11
identity the domain of the function shown in the graph
The domain of the function is x ≥ 0
Calculating the domain of the function?From the question, we have the following parameters that can be used in our computation:
The graph
The above graph is an square root function
The rule of a function is that
The domain is the set of input values
From the graph, we have the input values to be greater than or equal to 0
So, we have
x ≥ 0
Read more about domain at
brainly.com/question/27910766
#SPJ1