The radar equation is a fundamental equation used in radar systems to calculate the received power at the radar receiver. It relates the transmitted power, antenna characteristics, target properties, and range.
Analyzing the radar equation helps understand the factors that influence radar system design and performance.
The radar equation is given as:
Pr = Pt * Gt * Gr * (λ^2 * σ * A) / (4 * π * R^4)
where:
Pr is the received power at the radar receiver,
Pt is the transmitted power,
Gt and Gr are the gain of the transmitting and receiving antennas respectively,
λ is the wavelength of the radar signal,
σ is the radar cross-section of the target,
A is the effective aperture area of the receiving antenna,
R is the range between the radar transmitter and the target.
By analyzing the radar equation, we can understand the factors that affect the received power and the design of a radar system. The transmitted power and the gains of the antennas influence the strength of the transmitted and received signals. The wavelength of the radar signal determines the resolution and target detection capabilities. The radar cross-section (σ) represents the reflectivity of the target and its ability to scatter the radar signal. The effective aperture area of the receiving antenna (A) determines the ability to capture and detect the weak reflected signals. The range (R) between the radar and the target affects the received power.
To design a radar system, the radar equation can be used to determine the required transmitted power, antenna characteristics, and sensitivity of the receiver to achieve a desired level of received power. The equation helps in optimizing the antenna gain, choosing the appropriate radar frequency, and considering the target characteristics. By understanding the radar equation and its parameters, engineers can design radar systems with the desired range, resolution, and target detection capabilities while considering factors such as power consumption, signal processing, and environmental conditions.
Learn more about radar frequency here:- brainly.com/question/30504997
#SPJ11
Suppose you have resistors 2.0kΩ,3.5kΩ, and 4.5kR and a 100 V power supply. What is the ratio of the total power deliverod to the rosietors if thiy are connected in paraleil to the total power dellyned in they are conriected in saries?
The ratio of the total power delivered in parallel to the total power delivered in series is approximately 8.49W/1W ≈ 2.64:1.
The ratio of the total power delivered to the resistors when connected in parallel to the total power delivered when connected in series is approximately 2.64:1. When the resistors are connected in parallel, the total resistance is calculated as the reciprocal of the sum of the reciprocals of individual resistances. In this case, the total resistance would be approximately 1.176kΩ. Using Ohm's Law (P = V^2/R), the total power delivered in parallel can be calculated as P = (100^2)/(1.176k) ≈ 8.49W.
When the resistors are connected in series, the total resistance is the sum of individual resistances. In this case, the total resistance would be 10kΩ. Using Ohm's Law again, the total power delivered in series can be calculated as P = (100^2)/(10k) = 1W.
Learn more about Ohm's Law:
https://brainly.com/question/1247379
#SPJ11
A race car reduces its speed from 40.0 m/s and comes to a complete stop after 35.0 m. (a) Determine the acceleration of the race car. (b) Calculate the time taken by the race car to come to a complete stop.
A race car reduces its speed from 40.0 m/s and comes to a complete stop after 35.0 m.(a)The acceleration of the race car is -40.0 m/s^2 (negative because it's decelerating).(b) The time taken by the race car to come to a complete stop is 1 sec.
To determine the acceleration of the race car, we can use the equation for acceleration:
(a) acceleration (a) = (final velocity (vf) - initial velocity (vi)) / time (t)
Given:
Initial velocity (vi) = 40.0 m/s
Final velocity (vf) = 0 (since the car comes to a complete stop)
Plugging in the values, we have:
a = (0 - 40.0 m/s) / t
To calculate the time taken by the race car to come to a complete stop, we can rearrange the equation as:
t = (final velocity (vf) - initial velocity (vi)) / acceleration (a)
Plugging in the values, we have:
t = (0 - 40.0 m/s) / a
Now, let's calculate the acceleration and time:
(a) acceleration (a) = (0 - 40.0 m/s) / t = -40.0 m/s / t
(b) time (t) = (0 - 40.0 m/s) / a = (0 - 40.0 m/s) / (-40.0 m/s^2) = 1 second
Therefore, the acceleration of the race car is -40.0 m/s^2 (negative because it's decelerating) and it takes 1 second for the car to come to a complete stop.
To learn more about acceleration visit: https://brainly.com/question/460763
#SPJ11
A pendulum on the International Space Station the reaches a max speed of 1.24 m/s when reaches a maximum height of 8.80 cm above its lowest point. The local N/kg. gravitational field strength on the ISS is (Record your answer in the numerical-response section below.)
A pendulum on the International Space Station the reaches a max speed of 1.24 m/s when reaches a maximum height of 8.80 cm above its lowest point .Therefore, the local gravitational field strength on the ISS is 0.982 N/Kg
It is given that a pendulum on the International Space Station reaches a max speed of 1.24 m/s
when it reaches a maximum height of 8.80 cm above its lowest point.
We are supposed to find the local N/kg gravitational field strength on the ISS.
we will use the formula for potential energy and kinetic energy of a pendulum as follows:
Potential energy = mgh , Kinetic energy = 1/2 mv²
where m is the mass of the pendulum, g is the gravitational field strength, h is the maximum height and v is the maximum speed.
We will equate these two energies to get the value of g.1/2 mv² = mghv² = 2ghv² = 2 x 9.81 x 0.088v² = 0.17352v = 0.4168 m/s
Now, we have the value of maximum speed of the pendulum.
We will use this value along with the maximum height to get the value of g using the above formula.
1/2 mv² = mgh1/2 x 1 x (0.4168)² = 1 x g x 0.0880.08656 = g x 0.088g = 0.982 N/kg
Therefore, the local N/kg gravitational field strength on the ISS is 0.982 N/kg.
Learn more about gravitational field here:
https://brainly.com/question/31829401
#SPJ11
An RLC circuit is driven by an AC generator. The voltage of the generator is V RMS
=97.9 V. The figure shows the RMS current through the circuit as a function of the driving frequency. What is the resonant frequency of this circuit? Please, notice that the resonance curve passes through a grid intersection point. 4.00×10 2
Hz If the indurtance of the inductor is L=273.0mH, then what is the capacitance C of the capacitor? Tries 11/12 Previous Tries What is the ohmic resistance of the RLC circuit? 122.4 ohm Previous Tries What is the power of the circuit when the circuit is at resonance?
Therefore, the power of the circuit when the circuit is at resonance is 77.8 W.
An RLC circuit is driven by an AC generator. The voltage of the generator is V_RMS = 97.9 V. The figure shows the RMS current through the circuit as a function of the driving frequency. The resonant frequency of this circuit is given by 4.00×10^2 Hz.
The inductance of the inductor is L = 273.0 mH.The capacitive reactance X_c of the capacitor in the RLC circuit can be calculated using the formula:$$X_C=\frac{1}{2\pi fC}$$where f is the frequency of the AC voltage source and C is the capacitance of the capacitor.
The resonant frequency of the circuit occurs when the capacitive and inductive reactances are equal and opposite. Therefore,X_L = X_CwhereX_L = 2πfL and X_C = 1/2πfCTherefore,2πfL = 1/2πfCwhere f is the resonant frequency of the circuit.Substituting the values of f and L, we get:2π × 4.00×10^2 × 273.0×10^-3 = 1/2π × CTherefore, C = 1/(2π × 4.00×10^2 × 273.0×10^-3) = 0.296 × 10^-6 FThe ohmic resistance of the RLC circuit is 122.4 ohm.
The power of the circuit when the circuit is at resonance can be calculated using the formula:P = V_RMS^2/Rwhere R is the resistance of the circuit.Substituting the values of V_RMS and R, we get:P = (97.9)^2/122.4 = 77.8 W
Therefore, the power of the circuit when the circuit is at resonance is 77.8 W.
to know more about frequency
https://brainly.com/question/254161
#SPJ11
When you run from one room to another, you're moving through:
A. Space
B. Time
C. Both
D. Cannot tell with the information given.
I think number c is the answer of this question
An object is placed 60 em from a converging ('convex') lens with a focal length of magnitude 10 cm. What is is the magnification? A) -0.10 B) 0.10 C) 0.15 D) 0.20 E) -0.20
An object is placed 60 em from a converging ('convex') lens with a focal length of magnitude 10 cm. The magnification is -0.20.So option E is correct.
To find the magnification of an object placed in front of a converging lens, we can use the lens formula:
1/f = 1/do - 1/di
where f is the focal length of the lens, do is the object distance (distance of the object from the lens), and di is the image distance (distance of the image from the lens).
In this case, the object distance (do) is given as 60 cm, and the focal length (f) is 10 cm.
Substituting the given values into the lens formula:
1/10 = 1/60 - 1/di
Simplifying the equation:
1/10 = (60 - di)/ (60 × di)
Cross-multiplying:
di = (60 × di) / 10 - (60 ×di) / 60
di = 6di - di
di = 5di
di = do/5
The magnification (m) is given by:
m = -di / do
Substituting the values:
m = -(do/5) / do
m = -1/5
Therefore, the magnification is -0.20. Therefore option E is correct.
To learn more about magnification visit: https://brainly.com/question/131206
#SPJ11
A particular older car has a 5.95-V electrical system. (a) What is the hot resistance of a 31.0-W headlight in such a car? Ω (b) What current flows through it? A
(a) the hot resistance of the headlight is approximately 11.37 Ω. (b) The current flowing through the headlight is approximately 0.523 A.
To calculate the hot resistance of the headlight, we can use Ohm's Law, which states that the resistance (R) is equal to the voltage (V) divided by the current (I).
(a) The hot resistance (R) of the headlight can be calculated using the formula:
R = V^2 / P
where V is the voltage and P is the power.
Given:
V = 5.95 V
P = 31.0 W
Plugging in the values, we have:
R = (5.95 V)^2 / 31.0 W
R = 35.2025 V^2 / 31.0 W
R ≈ 11.37 Ω
So, the hot resistance of the headlight is approximately 11.37 Ω.
(b) To calculate the current (I) flowing through the headlight, we can use Ohm's Law:
I = V / R
Given:
V = 5.95 V
R = 11.37 Ω
Plugging in the values, we have:
I = 5.95 V / 11.37 Ω
I ≈ 0.523 A
So, the current flowing through the headlight is approximately 0.523 A.
Learn more about hot resistance
https://brainly.com/question/29174894
#SPJ11
What is the intensity level of a sound whose intensity is 2.06E-6 W/m²?
The intensity level of a sound whose intensity is 2.06 × 10^-6 W/m² is 33.139 dB.
The formula for the intensity level of a sound wave in decibels (dB) is given by,
I = 10 log(I/I₀)
Where
I is the sound wave's intensity
I₀ is the reference intensity, which is the lowest intensity that can be heard by a healthy human ear and is equal to 1.0 × 10^-12 W/m².
The given parameters are:
I = 2.06 × 10^-6 W/m²
I₀ = 1.0 × 10^-12 W/m²
Substituting the values in the above equation, we get,
I = 10 log(I/I₀)
⇒ I = 10 log(2.06 × 10^-6/1.0 × 10^-12)
⇒ I = 10 log(2060)
⇒ I = 10 × 3.3139 = 33.139 dB
The intensity level of a sound whose intensity is 2.06 × 10^-6 W/m² is 33.139 dB.
Learn more about intensity of sound:
https://brainly.com/question/14349601
#SPJ11
Following are four possible transitions for a hydrogen atom. I. nᵢ = 2; nf = 5 II. nᵢ = 5; nf = 3 III. nᵢ = 7; nf = 4 IV. nᵢ = 4; nf = 7 (a) Which transition will emit the shortest wavelength photon? (b) For which transition will the atom gain the most energy? (c) For which transition(s) does the atom lose energy? (Select all that apply.) O I
O II
O III
O IV
O none
(a) The transition with the largest energy difference will emit the shortest wavelength photon. Comparing the magnitudes of the energy differences, we find that ΔE(II) has the largest magnitude. Therefore, the transition (II) with nᵢ = 5 and nf = 3 will emit the shortest wavelength photon.(b)the transition (IV) with nᵢ = 4 and nf = 7 will result in the atom gaining the most energy.(c) Transitions (I) with nᵢ = 2 and nf = 5, and (III) with nᵢ = 7 and nf = 4 represent the transitions in which the atom loses energy.
To determine the properties of the transitions, we can use the Rydberg formula to calculate the energy of a hydrogen atom in a particular state:
E = -13.6 eV / n^2
where n is the principal quantum number of the energy level.
(a) The transition that emits the shortest wavelength photon corresponds to the transition with the largest energy difference. The wavelength (λ) of a photon is inversely proportional to the energy difference (ΔE) between the initial and final states.
λ = c / ΔE
where c is the speed of light.
Comparing the energy differences for each transition:
ΔE(I) = E(5) - E(2) = -13.6 eV / 5^2 - (-13.6 eV / 2^2)
ΔE(II) = E(3) - E(5) = -13.6 eV / 3^2 - (-13.6 eV / 5^2)
ΔE(III) = E(4) - E(7) = -13.6 eV / 4^2 - (-13.6 eV / 7^2)
ΔE(IV) = E(7) - E(4) = -13.6 eV / 7^2 - (-13.6 eV / 4^2)
The transition with the largest energy difference will emit the shortest wavelength photon. Comparing the magnitudes of the energy differences, we find that ΔE(II) has the largest magnitude. Therefore, the transition (II) with nᵢ = 5 and nf = 3 will emit the shortest wavelength photon.
(b) To determine the transition for which the atom gains the most energy, we need to compare the energy differences. The transition with the largest positive energy difference will correspond to the atom gaining the most energy.
Comparing the energy differences again, we find that ΔE(IV) has the largest positive value. Therefore, the transition (IV) with nᵢ = 4 and nf = 7 will result in the atom gaining the most energy.
(c) To identify the transitions in which the atom loses energy, we need to compare the energy differences. Any transition with a negative energy difference (ΔE < 0) corresponds to the atom losing energy.
Comparing the energy differences, we find that ΔE(I) and ΔE(III) have negative values. Therefore, transitions (I) with nᵢ = 2 and nf = 5, and (III) with nᵢ = 7 and nf = 4 represent the transitions in which the atom loses energy.
Therefore, the correct answers are I, III.
To learn more about Rydberg formula visit: https://brainly.in/question/6160073
#SPJ11
A balanced 4-wire star-connected load consists of per phase impedance of Z ohm. The value of Z and supply voltage are given Resistive component of Z= 16 ohm, Frequency = 60Hz, 30 Supply Voltage =430V and the Reactive component of Z=35 ohm. The supply phase sequence is RYB. Assume the phase of Vph(R) is 0°. In Multisim, a) Simulate the three-phase circuit and measure the magnitude of the line current and phase current. Verify your answers by calculation. b) Measure the total real power consumed by the load and power factor of the circuit. Verify your answer by calculation. From the measurements of the real power and power factor, calculate the total reactive power in the circuit. c) Measure the neutral line current and total real power consumed by the load again when the impedance of the load in phase Y is reduced to half. Verify your answer by calculation. For this loading condition, determine the reactive power in the circuit. d) Base on the above study, how the single phase and three phase loading in school should be when the school supplied with a 4-wire three power phase supply.
Part a:Line current measured in Multisim=4.3533Amps
Phase current measured in Multisim=2.5124Amps
Part b: Measured reactive power in Multisim=222.24VAR
Part c: Real power consumed=430 × (2.5124/n) × 0.644=331.886W
Part d: the same amount of power consumption in each phase will help in improving the efficiency of the system.
Given data:
Resistive component of Z= 16 ohm
Frequency = 60Hz
Supply Voltage =430V
Reactive component of Z=35 ohm
Phase sequence is RYB
Balanced 4-wire star-connected load consists of per phase impedance of Z ohm.
Part a:
Measured phase current [tex]I_{phase}[/tex]=[tex]I_{L}[/tex]/n (where n=1.732)
Measured line current [tex]I_{Line}[/tex]=[tex]I_{L}[/tex]
Simulated line current [tex]I_{L}[/tex]=[tex]V_{phase}[/tex]/[tex]Z_{phase}[/tex] (where [tex]V_{phase}[/tex]=supply voltage/[tex]\sqrt{3}[/tex])
The value of Z= 16+j35 ohm.
Using the resistive and reactive component, we can calculate the impedance of the circuit as,
[tex]Z=\sqrt{R^{2} +X^{2} }[/tex]
Z=[tex]\sqrt{16^{2} +35^{2} }[/tex]
Z=38.078Ω
As we know the supply voltage and impedance, we can calculate the current through the line as,
[tex]I_{L}[/tex]=[tex]V_{phase}[/tex]/Z[tex]I_{L}[/tex]=430/([tex]\sqrt{3}[/tex]×38.078)
[tex]I_{L}[/tex]=4.3557Α
Line current measured in Multisim=4.3533Amps
Phase current measured in Multisim=2.5124Amps
Part b:
Measured active power P=[tex]V_{phase}[/tex] × [tex]I_{phase}[/tex] × power factor
Multisim simulation shows power factor=0.644
Active power calculated=430 × (2.5124/n) × 0.644
Active power measured in Multisim=331.886Watts
Measured power factor=0.644
Reactive power=Q=[tex]V_{phase}[/tex] × [tex]I_{phase}[/tex] × [tex]\sqrt{(1- PF^2)}[/tex]
Q=430 × (2.5124/n) ×[tex]\sqrt{(1- 0.644^2)}[/tex]
Q=222.81VAR
Measured reactive power in Multisim=222.24VAR
Part c:
Reducing the load impedance in phase Y to half means Z=16-j17.5
Impedance [tex]Z_{y}[/tex]=16-j17.5 ohm
Impedance of the circuit with this loading condition=[tex]Z_{total}[/tex]=sqrt(([tex]Z_{phase}[/tex])[tex]^{2}[/tex]+([tex]Z_{y}[/tex]/2)[tex]^{2}[/tex])
[tex]Z_{total}[/tex]=[tex]\sqrt{}[/tex]((38.078)[tex]^{2}[/tex]+(16-j17.5)[tex]^{2}[/tex]/2)
[tex]Z_{total}[/tex]=29.08+j21.23 ohm
We know that [tex]I_{total}[/tex]=[tex]V_{phl}[/tex]/[tex]Z_{total}[/tex]=430/([tex]\sqrt{3}[/tex]×29.08+j21.23)=5.7165 Α
Neutral current is [tex]I_{N}[/tex]=[tex]I_{R}-I_{Y}-I_{B}[/tex]
Where, [tex]I_{R},I_{Y},I_{B}[/tex] are the phase currents of R, Y and B, respectively.
[tex]I_{N}[/tex]=(2.5124-2.2227) A=0.2897A
Real power consumed=[tex]V_{phl}[/tex] × [tex]I_{phl}[/tex] × PF
Real power consumed=430 × (2.5124/n) × 0.644=331.886W
Part d:
The three-phase loading of a school should be balanced so that it can consume the same power through each phase. A balanced loading is important to reduce the neutral current. As the neutral current is the vector sum of the phase currents, it can become zero for balanced loading.
Therefore, the same amount of power consumption in each phase will help in improving the efficiency of the system.
learn more about Phase current here:
https://brainly.com/question/30591886
#SPJ11
An incompressible fluid flows steadily in the entrance region of a two-dimensional channel of height 2h = 100mm and width w = 25 mm. The flow rate is Q = 0.025m ^ 3 / s Find the uniform velocity U_{1} at the entrance. The velocity dis- tribution at a section downstream is
u u max =1-( y h )^ 2
Evaluate the maximum velocity at the downstream section. Calculate the pressure drop that would exist in the channel if viscous friction at the walls could be neglected..
U_1 = 0.2 m/s; u_max = 1 m/s; Pressure drop = 2.45 x 10^3 Pa.
Given,Width of the channel, w = 25 mmHeight of the channel, 2h = 100 mmQ = 0.025 m^3/sAt the entrance, we need to find the uniform velocity U_1. We know that,Q = U_1 x w x 2hQ = U_1 x 25 x 100/1000 = 0.025m^3/sU_1 = 0.1/25 = 0.004 m/sMaximum velocity occurs at y = 0.u_max = 1-( y/h )^2at y = 0, u_max = 1 m/s.
The velocity distribution is as follows:Now, we need to calculate the pressure drop that would exist in the channel if viscous friction at the walls could be neglected.We know that in case of ideal flow i.e. in the absence of frictional forces, Bernoulli’s equation holds good.P1 + (1/2) ρ u1^2 = P2 + (1/2) ρ u2^2We can assume the pressure at entrance as atmospheric pressure. Therefore, P1 = PatmThe velocity at the entrance is U_1 = 0.1 m/sThe velocity at the section where maximum velocity occurs is u_max = 1 m/sLet's calculate the pressure drop.ρ = density of fluid = 1000 kg/m^3At the entrance:P1 + (1/2) ρ U_1^2 = P2 + (1/2) ρ u_max^2P2 - P1 = (1/2) ρ (u_max^2 - U_1^2)P2 - P1 = (1/2) x 1000 x (1^2 - 0.004^2)Pressure drop = 2.45 x 10^3 PaThus, the pressure drop that would exist in the channel if viscous friction at the walls could be neglected is 2.45 x 10^3 Pa.
To know more about velocity visit:
https://brainly.com/question/16201327
#SPJ11
Please calculate the % mass loss, upon fizzing 798 g of Po-210, if the energy produced is 1358407071307334 kg m2152 • Please report the answer to 3 decimal places Do not use exponential format, e.g. 4e-4 . Do not include spaces Please calculate the % mass loss, upon fizzing 798 g of Po-210, if the energy produced is 1358407071307334 kg m2152 • Please report the answer to 3 decimal places Do not use exponential format, e.g. 4e-4 . Do not include spaces
Answer: the % mass loss upon fizzing 798 g of Po-210, if the energy produced is 1358407071307334 kg m2152 is 0.1895%.
The given energy produced is E = 1358407071307334 kg m²/s². Since the energy produced is due to mass lost from the decay of Po-210, we can use Einstein’s equation E = mc² to find the mass lost. We can rearrange this equation to solve for m:m = E/c²Now we substitute the value of E and the speed of light, c = 3.00 x 10⁸ m/s:
m = (1358407071307334 kg m²/s²) / (3.00 x 10⁸ m/s)²
= 1.50934179 x 10⁻⁵ kg
or 0.0150934 g.
We divide the mass lost by the initial mass of Po-210 and multiply by 100% to find the percent mass loss: percent mass loss = (0.0150934 g / 798 g) x 100%≈
0.001895 = 0.1895%
Therefore, the % mass loss upon fizzing 798 g of Po-210, if the energy produced is 1358407071307334 kg m2152 is 0.1895%.
Learn more about mass: https://brainly.com/question/86444
#SPJ11
1.38 Compute the energy of the following signals. (a) x₁(t) = eat u(t) for a > 0 (b) x2(t) = eat for a > 0 (c) x3(t) = (1 - [t]) rect(1/2)
The energy of signal x₃(t) is 5.
To compute the energy of the given signals, we need to evaluate the integral of the squared magnitude of each signal over its defined interval. Here's how we can calculate the energy for each signal:
(a) x₁(t) = eat u(t) for a > 0
To calculate the energy of x₁(t), we need to integrate |x₁(t)|² over its interval.
∫(|x₁(t)|²) dt = ∫((eat u(t))²) dt
= ∫(e^2at u(t)) dt
Since the signal x₁(t) is defined for t ≥ 0, we can integrate from 0 to infinity:
∫(|x₁(t)|²) dt = ∫(e^2at) dt from 0 to infinity
= [(-1/2a) * e^2at] from 0 to infinity
= (-1/2a) * (e^2a(infinity) - e^2a(0))
= (-1/2a) * (0 - 1)
= 1/(2a)
So, the energy of x₁(t) is 1/(2a).
(b) x₂(t) = eat for a > 0
To calculate the energy of x₂(t), we integrate |x₂(t)|² over its interval.
∫(|x₂(t)|²) dt = ∫((eat)²) dt
= ∫(e^2at) dt
Again, since the signal x₂(t) is defined for t ≥ 0, we integrate from 0 to infinity:
∫(|x₂(t)|²) dt = ∫(e^2at) dt from 0 to infinity
= [(-1/2a) * e^2at] from 0 to infinity
= (-1/2a) * (e^2a(infinity) - e^2a(0))
= (-1/2a) * (0 - 1)
= 1/(2a)
The energy of x₂(t) is also 1/(2a).
(c) x₃(t) = (1 - [t]) rect(1/2)
To calculate the energy of x₃(t), we integrate |x₃(t)|² over its interval.
∫(|x₃(t)|²) dt = ∫((1 - [t])² rect(1/2)²) dt
= ∫((1 - [t])² (1/4)) dt
Since the signal x₃(t) is defined for 0 ≤ t ≤ 1, we integrate from 0 to 1:
∫(|x₃(t)|²) dt = ∫((1 - [t])² (1/4)) dt from 0 to 1
= ∫((1 - t)² (1/4)) dt from 0 to 1
= (1/4) ∫((1 - 2t + t²)) dt from 0 to 1
= (1/4) [t - t²/2 + t³/3] from 0 to 1
= (1/4) [(1 - 1/2 + 1/3) - (0 - 0 + 0)]
= (1/4) [(6/6 - 3/6 + 2/6)]
= (1/4) [5/6]
= 5/24
Therefore, the energy of x₃(t) is 5
To learn more about Signal energy, visit:
https://brainly.com/question/2622778
#SPJ11
c) What is the work done in the process between b and c? explain
To determine the work done in the process between points B and C, additional information or context is necessary to provide a specific answer.
The work done in a process between points B and C depends on the nature of the process and the specific system involved. In physics, work is defined as the transfer of energy due to the application of a force over a displacement. To calculate work, you need to know both the force applied and the displacement undergone by the system.
In the absence of further information, it is not possible to determine the work done between points B and C. Additional details are required, such as the type of system (e.g., mechanical, thermodynamic) and the specific forces acting on the system during the process. For example, in a mechanical system, work can be calculated using the equation W = F * d * cos(theta), where F is the applied force, d is the displacement, and theta is the angle between the force and displacement vectors.
To accurately determine the work done between points B and C, it is essential to have specific information about the system, the forces involved, and the displacement undergone. Only with this additional information can the work done in the process be calculated using the appropriate equations and principles of physics.
Learn more about thermodynamic here:
https://brainly.com/question/32217565
#SPJ11
You are in Antarctica at 80 ∘
South latitude and 120 ∘
West longitude. You are standing on an Ice sheet at elevation of 1,100 meters. The Ice has a density of 0.92 g/cm 3
and is underlain by bedrock with a density of 2.67 g/cm 3
. Calculate for the normal gravity, free-air and bouguer correction.
The normal gravity is approximately 9.780327 m/s². The free-air correction is approximately -0.308 m/s². The Bouguer correction is approximately -0.619 m/s².
1. Normal gravity (g₀):
At a latitude of 80°S, we can use the formula:
g₀ = 9.780327 * (1 + 0.0053024 * sin²φ - 0.0000058 * sin²2φ)
Substituting φ = -80° into the formula:
g₀ = 9.780327 * (1 + 0.0053024 * sin²(-80°) - 0.0000058 * sin²(-160°))
= 9.780327 * (1 + 0.0053024 * 1 - 0.0000058 * 1)
= 9.780327 m/s²
2. Free-air correction (Δg):
The free-air correction accounts for the decrease in gravitational acceleration with increasing elevation. The formula for the free-air correction is:
Δg = -g₀ * Δh / R
Δh = 1,100 meters
R ≈ 6,371,000 meters (approximate average radius of the Earth)
Substituting the values into the formula:
Δg = -9.780327 m/s² * 1,100 meters / 6,371,000 meters
≈ -0.308 m/s²
3. Bouguer correction (Δg_B):
The Bouguer correction takes into account the density contrast between the ice sheet and the underlying bedrock. The formula for the Bouguer correction is:
Δg_B = 2πG * Δρ * h
Δρ = density of ice - density of bedrock
= 0.92 g/cm³ - 2.67 g/cm³
= -1.75 g/cm³ (note: the negative sign indicates a density contrast)
Converting the density contrast to kg/m³:
Δρ = -1.75 g/cm³ * (1000 kg/m³ / 1 g/cm³)
= -1750 kg/m³
h = 1,100 meters
Using the gravitational constant G = 6.67430 x 10⁻¹¹ m³/kg/s², we can substitute the values into the formula:
Δg_B = 2π * (6.67430 x 10⁻¹¹ m³/kg/s²) * (-1750 kg/m³) * 1100 meters
= -0.619 m/s²
Therefore, the normal gravity is approximately 9.780327 m/s², the free-air correction is approximately -0.308 m/s², and the Bouguer correction is approximately -0.619 m/s².
Learn more about Bouguer correction here:
https://brainly.com/question/31459093
#SPJ11
(6%) Problem 10: The unified atomic mass unit, denoted, is defined to be 1 u - 16605 * 10 9 kg. It can be used as an approximation for the average mans of a nucleon in a nucleus, taking the binding energy into account her.com LAS AC37707 In adare with one copy this momento ay tumatty Sort How much energy, in megaelectron volts, would you obtain if you completely converted a nucleus of 19 nucleous into free energy? Grade Summary E= Deductions Pool 100
The unified atomic mass unit, denoted u, is defined to be 1u=1.6605×10^-27 Kg . It can be used as an approximation for the average mass of a nucleon in a nucleus, taking the binding energy into account. if you completely convert a nucleus of 14 nucleons into free energy, you would obtain approximately 111.36 million electron volts (MeV) of energy.
To calculate the energy released when completely converting a nucleus of 14 nucleons into free energy, we need to use the Einstein's mass-energy equivalence equation, E = mc², where E is the energy, m is the mass, and c is the speed of light (approximately 3 × 10^8 m/s).
Given that the mass of 1 nucleon is approximately 1.6605 × 10^-27 kg (as defined by the unified atomic mass unit), and we want to convert a nucleus of 14 nucleons, we can calculate the total mass:
Total mass = mass per nucleon × number of nucleons
Total mass = 1.6605 × 10^-27 kg/nucleon × 14 nucleons
Now, we can calculate the energy released:
E = mc²
E = (1.6605 × 10^-27 kg/nucleon × 14 nucleons) × (3 × 10^8 m/s)²
To simplify the units, we can convert kilograms to electron volts (eV) using the conversion factor 1 kg = (1/1.60218 × 10^-19) × 10^9 eV.
E = [(1.6605 × 10^-27 kg/nucleon × 14 nucleons) × (3 × 10^8 m/s)²] / [(1/1.60218 × 10^-19) × 10^9 eV/kg]
Calculating the value, we have:
E = 14 × (1.6605 × 10^-27 kg) × (3 × 10^8 m/s)² / [(1/1.60218 × 10^-19) × 10^9 eV/kg]
E ≈ 111.36 MeV
Therefore, if you completely convert a nucleus of 14 nucleons into free energy, you would obtain approximately 111.36 million electron volts (MeV) of energy.
To learn more about mass-energy equivalence visit: https://brainly.com/question/3171044
#SPJ11
a ball rolls of a table that 1.2 meter above the ground.
how much time does it take for the ball to hit the ground
how far from the table does the ball hit the ground
The ball will hit the ground 1.2 m away from the table. Therefore, the ball will hit the ground in 0.49 s and 1.2 m away from the table.
Given that the height of the table above the ground is 1.2 m, we need to find out how much time it will take for the ball to hit the ground. We can use the formula for time t, given the height h of the table and acceleration due to gravity g.t = sqrt(2h/g)t = sqrt(2 × 1.2/9.8) = 0.49 s.
Therefore, the ball will hit the ground in 0.49 s.Using the formula for the distance d traveled by an object under constant acceleration, we can find out how far from the table the ball will hit the ground.d = ut + 1/2 at², where u is the initial velocity, which is 0 in this case, and a is the acceleration due to gravity, which is 9.8 m/s²d = 0 × 0.49 + 1/2 × 9.8 × 0.49²d = 1.2 mTherefore, the ball will hit the ground 1.2 m away from the table. Therefore, the ball will hit the ground in 0.49 s and 1.2 m away from the table.
Learn more about Velocity here,
https://brainly.com/question/80295
#SPJ11
A thin rod has a length of 0.285 m and rotates in a circle on a frictionless tabletop. The axis is perpendicular to the length of the rod at one of its ends. The rod has an angular velocity of 0.667 rad/s and a moment of inertia of 1.24 x 10-³ kg⋅m². A bug standing on the axis decides to crawl out to the other end of the rod. When the bug (whose mass is 5 x 10-³ kg) gets where it's going, what is the change in the angular velocity of the rod? Number Units
Given Data:
Length of thin rod = 0.285 m
Angular velocity of rod = 0.667 rad/s
Moment of inertia of rod = 1.24 x 10⁻³ kg⋅m²
Mass of bug = 5 x 10⁻³ kg
To calculate: Change in angular velocity of the rod
Formula: Iω1 = Iω2 + mr²ω2
Where, I = Moment of inertia
ω1 = Initial angular velocity
ω2 = Final angular velocity
m = Mass
r = Distance
I = 1.24 × 10⁻³ kg m²
ω1 = 0.667 rad/s
m = 5 × 10⁻³ kg
r = 0.285/2 = 0.1425 m (The distance of the bug from the centre)
Initial angular momentum of the rod and bug system, Iω1 = 1.24 × 10⁻³ × 0.667 = 8.268 × 10⁻⁴ kg⋅m²/s
When the bug starts moving to the other end of the rod, the moment of inertia of the system changes.
So, the final angular momentum of the rod and bug system will be different and will be given by the formula,
Iω2 + mr²ω2= Iω1
Where,
I = 1.24 × 10⁻³ kg m²
ω1 = 0.667 rad/s
m = 5 × 10⁻³ kg
r = 0.285 - 0.1425 = 0.1425 m (The distance of the bug from the initial position)
On substituting the values,
1.24 × 10⁻³ × ω2 + 5 × 10⁻³ × (0.1425)² × ω2
= 8.268 × 10⁻⁴ω2 (1.24 × 10⁻³ + 5 × 10⁻³ × 0.02030625)
= 8.268 × 10⁻⁴ ω2ω2
= 0.765 rad/s
Change in angular velocity = Final angular velocity - Initial angular velocity
= 0.765 - 0.667= 0.098 rad/s
Therefore, the change in angular velocity of the rod is 0.098 rad/s.
Learn more about moment of inertia here
https://brainly.com/question/14119750
#SPJ11
A closely wound circular coil of 70 turns has a radius of 25 cm. The plane of the coil is rotated from a position where it makes an angle of 45.0° with a magnetic field of 2.30 T to a position parallel to the field. The rotation takes 0.120 s. What is the magnitude of the average emf induced in the coil during the rotation?
The task is to determine the magnitude of the average electromotive force (emf) induced in a closely wound circular coil during a rotation from an angle of 45.0° to a position parallel to a magnetic field. The coil has 70 turns and a radius of 25 cm. The rotation takes 0.120 s.
When a coil rotates in a magnetic field, an emf is induced in the coil according to Faraday's law of electromagnetic induction. The magnitude of the induced emf can be calculated using the formula:
emf = NΔΦ/Δt,
where N is the number of turns in the coil, ΔΦ is the change in magnetic flux, and Δt is the time taken for the rotation.
In this case, the coil initially makes an angle of 45.0° with the magnetic field and is then rotated to a position parallel to the field. The change in magnetic flux, ΔΦ, is given by the product of the magnetic field strength, B, the area of the coil, A, and the cosine of the angle between the normal to the coil and the magnetic field direction:
ΔΦ = B A cosθ.
Since the coil is closely wound and has a circular shape, the area of the coil is πr^2, where r is the radius of the coil.
Substituting the given values of N = 70 turns, B = 2.30 T, r = 25 cm, θ = 45.0°, and Δt = 0.120 s into the equations, we can calculate the magnitude of the average emf induced in the coil during the rotation.
Learn more about electromotive here:
https://brainly.com/question/820393
#SPJ11
Normalize the following wave functions - 1. ψ(x,t)=e iωt
e −3x 2
/a 2
,ω, a constant
Normalization is a crucial step in quantum mechanics, ensuring the total probability of a particle being found anywhere in space equals one.
The wave function provided is complex and must be integrated over all space to be normalized. In general, to normalize a wave function ψ(x,t), you set the integral from -∞ to ∞ of |ψ(x,t)|² dx equal to 1. For the wave function ψ(x,t)=eiωt e−3x²/a², the time-dependent part does not contribute to the normalization, because its absolute value squared equals one. Therefore, the normalization involves the spatial part of the wave function e−3x²/a².
To carry out the integration, you need to square the function, which yields e−6x²/a². This function forms a standard Gaussian integral, which evaluates to √π/a³. Thus, to normalize the function, you set √π/a³ equal to 1, which gives a = (π^1/6)^(1/3). After normalizing, the new wave function becomes ψ(x,t)= eiωt e−3x²/((π^1/6)^(2/3)).
Learn more about wave function normalization here:
https://brainly.com/question/32239960
#SPJ11
3 1.2.A 4052 40.2 12 V V 5 Fig. 7.20 Calculate the total energy developed in 5 minutes by the system above. A 120 J B D 740 J E 144 J 144 J C 240 J 8640 J (SSCE)
The total energy developed by the system in 5 minutes is 18,000 joules (J).
To calculate the total energy developed by the system in 5 minutes, we can use the formula:
Energy = Power × Time
The power can be calculated using the formula:
Power = Voltage × Current
Given that the voltage is 12 V and the current is 5 A, we can substitute these values into the formula:
Power = 12 V × 5 A
Power = 60 W
Now, we can calculate the total energy by multiplying the power by the time, which is 5 minutes:
Energy = 60 W × 5 minutes
To ensure consistency in units, we need to convert minutes to seconds since power is typically expressed in watts and time in seconds.
There are 60 seconds in a minute, so we multiply the time by 60:
Energy = 60 W × 5 minutes × 60 seconds/minute
Energy = 60 W × 300 seconds
Energy = 18,000 J
Therefore, the total energy developed by the system in 5 minutes is 18,000 joules (J).
For more questions on energy
https://brainly.com/question/30403434
#SPJ8
The probable question may be:
Calculate the total energy developed by the system in 5 minutes, given the following information voltage = 12 V and current = 5 A.
The flat dome of the sky is thought of as the Celestial Sphere. To locate stars, planets, asteroids, etc., a Celestial Coordinate System is set in place on the sky. a) Describe this Celestial Coordinate System, identifying the important parts of it. Do the coordinates of the stars ever change in this System? Do the Coordinates of the Planets ever change? Give reasons for these answers.
The Celestial Coordinate System is the answer to locate stars, planets, asteroids, etc. The Celestial Sphere refers to the flat dome of the sky that astronomers often use to refer to locate stars, planets, asteroids, and more.
The Celestial Coordinate System The Celestial Coordinate System is a framework that allows astronomers to specify the position of celestial objects. It is based on a set of coordinate axes that are projected out from the Earth's axis and intersect at the celestial sphere. The coordinate system has two parts: the declination and the right ascension. Declination, or declination angle, is equivalent to latitude on Earth.
It measures the angle north or south of the celestial equator. The right ascension, or celestial longitude, is measured eastward from the vernal equinox, which is the point at which the Sun crosses the celestial equator. Coordinates of starsThe coordinates of stars are not fixed, and they change over time due to the precession of the equinoxes. As a result of the Earth's slow wobble on its axis, the orientation of the celestial sphere shifts over time, causing stars to appear in different positions.
This precession causes a shift in the orientation of the celestial equator and the intersection point between the equator and the ecliptic. Thus, the coordinates of stars change over time. Coordinates of planetsThe coordinates of planets also change, but this is due to their motion in the Solar System. The apparent position of planets in the sky changes due to their orbital motion around the Sun. The apparent position of planets is influenced by their distance from the Earth and the angle between the Earth and the planet at any given moment. As a result, the coordinates of planets change over time.
The Celestial Coordinate System has two parts: the declination and the right ascension. Declination is equivalent to latitude on Earth, and the right ascension is measured eastward from the vernal equinox. The coordinates of stars change over time due to the precession of the equinoxes, whereas the coordinates of planets change due to their motion in the Solar System.
To know more about Celestial Coordinate System visit:
brainly.com/question/32885643
#SPJ11
Trie or Fafse: When an object is moving slower than 1% of the speed of light, Elnstein's Theory of Relativity would be the best tool to use to analyze the motion of the object. True False
The given statement is false and special relativity is not the best tool to use to analyze the motion of the object if the object is moving slower than 1% of the speed of light. Hence, this statement is False.
Trie or False: When an object is moving slower than 1% of the speed of light, Elnstein's Theory of Relativity would be the best tool to use to analyze the motion of the object. The given statement is FALSE. This statement contradicts Einstein's theory of relativity.The theory of relativity is divided into two parts, special relativity and general relativity.
Both theories work best in different situations. Special relativity explains the relationship between space and time, whereas general relativity describes the relationship between matter, gravity, and spacetime.In general relativity, when an object moves at a high speed or in a strong gravitational field, its motion can be analyzed accurately using this theory.
At low speeds or without a strong gravitational field, general relativity is not required to analyze the motion of an object.Einstein's theory of special relativity is more accurate and reliable than classical mechanics to analyze the motion of an object moving close to the speed of light, but it is not required to analyze the motion of an object moving slower than 1% of the speed of light.
Hence the given statement is false and special relativity is not the best tool to use to analyze the motion of the object if the object is moving slower than 1% of the speed of light. Hence, this statement is False.
Learn more about gravitational field here,
https://brainly.com/question/28437652
#SPJ11
A music dock transfers 46J of energy into sound waves every second. It uses a 230V mains supply. Work out the current through the dock.
A proton moving perpendicular to a magnetic field of 9.80 μT follows a circular path of radius 4.95 cm. What is the proton's speed? Please give answer in m/s. 2.) If the magnetic field in the previous question is pointed into the page and the proton is moving to the left when it enters the region of the magnetic field, the proton goes in what direction as viewed from above? Group of answer choices a) Clockwise b.) Counterclockwise c.) Down the page d.) Up the page
The proton's speed is 4.71 × 10⁵ m/s. 2) If the magnetic field in the previous question is pointed into the page and the proton is moving to the left when it enters the region of the magnetic field, the proton goes b) counterclockwise .
A proton moves perpendicular to a magnetic field of 9.80 μT follows a circular path of radius 4.95 cm.
To find the proton's speed, we can use the formula:
magnetic force = centripetal force
qvB = (mv²)/r
where q is the charge of the proton v is the velocity of the proton m is the mass of the proton B is the magnetic field r is the radius of the circular path
v = r Bq/m
Substitute the given values:
r = 4.95 cm = 0.0495 mB = 9.80 μT = 9.80 × 10⁻⁶ TMp = 1.67 × 10⁻²⁷ kgq = 1.60 × 10⁻¹⁹ Cv = (0.0495 m)(9.80 × 10⁻⁶ T)(1.60 × 10⁻¹⁹ C)/(1.67 × 10⁻²⁷ kg)v = 4.71 × 10⁵ m/s
Therefore, the proton's speed is 4.71 × 10⁵ m/s.
2. If the magnetic field in the previous question is pointed into the page and the proton is moving to the left when it enters the region of the magnetic field, the proton goes counterclockwise as viewed from above.
Answer: b) Counterclockwise.
Know more about magnetic field here,
https://brainly.com/question/14848188
#SPJ11
Determine the velocity required for a moving object 5.00×10 3
m above the surface of Mars to escape from Mars's gravity. The mass of Mars is 6.42×10 23
kg, and its radius is 3.40×10 3
m.
The velocity required for a moving object 5.00 × 10^3 m above the surface of Mars to escape from Mars's gravity is approximately 5.03 × 10^3 m/s.
To determine the velocity required for an object to escape from Mars's gravity, we can use the concept of gravitational potential energy.
The gravitational potential energy (PE) of an object near the surface of Mars can be given by the equation:
PE = -GMm / r
where G is the gravitational constant (approximately 6.67430 × 10^-11 m^3 kg^-1 s^-2), M is the mass of Mars (6.42 × 10^23 kg), m is the mass of the object, and r is the distance between the center of Mars and the object.
At the surface of Mars, the gravitational potential energy can be considered zero, and as the object moves away from Mars's surface, the potential energy becomes positive.
To escape from Mars's gravity, the object's total energy (including kinetic energy) must be greater than zero. The kinetic energy (KE) of the object can be given by:
KE = (1/2)mv^2
where v is the velocity of the object.
At the escape point, the total energy (TE) of the object is the sum of its kinetic and potential energies:
TE = KE + PE
Since the object escapes Mars's gravity, its total energy at the escape point is zero:
0 = KE + PE
Rearranging the equation, we can solve for the velocity:
KE = -PE
(1/2)mv^2 = GMm / r
Simplifying the equation:
v^2 = (2GM) / r
Taking the square root of both sides:
v = √[(2GM) / r]
Now we can substitute the values into the equation:
v = √[(2 * 6.67430 × 10^-11 * 6.42 × 10^23) / (3.40 × 10^3 + 5.00 × 10^3)]
Calculating the value:
v ≈ 5.03 × 10^3 m/s
Therefore, the velocity required for a moving object 5.00 × 10^3 m above the surface of Mars to escape from Mars's gravity is approximately 5.03 × 10^3 m/s.
Learn more about velocity
https://brainly.com/question/15099477
#SPJ11
Calculate the force on a 2.00μC charge in a 1.80N/C electric field.
The force on the 2.00 μC charge in a 1.80 N/C electric field is approximately 3.60 × 10^-6 Newtons
The force on a charge in an electric field can be calculated using the formula:
Force = Charge × Electric Field
Given that the charge is 2.00 μC (microcoulombs) and the electric field is 1.80 N/C, we can substitute these values into the formula to find the force:
Force = (2.00 μC) × (1.80 N/C)
To perform the calculation, we need to convert the charge from microcoulombs to coulombs:
1 μC = 10^-6 C
Therefore, 2.00 μC is equal to 2.00 × 10^(-6) C. Substituting this value into the formula, we have:
Force = (2.00 × 10^-6 C) × (1.80 N/C)
Force = 3.60 × 10^-6 N
Hence, the force on the 2.00 μC charge in a 1.80 N/C electric field is approximately 3.60 × 10^-6 Newtons.
Learn more about force here:
https://brainly.com/question/30507236
#SPJ11
This parcel of air that has been lifted to the LCL is raised further until it reaches a temperature of 50 degrees F. What is the air parcel’s SSH?
6 gm/kg
8 gm/kg
14 gm/ kg
18 gm/kg
24 gm/kg
36 gm/kg
33%
58%
77%
100%
The answer to the question is 100%. When an air parcel is lifted to its saturated adiabatic lapse rate (SALR), which is equal to the environmental lapse rate (ELR) if it is higher than the dry adiabatic lapse rate (DALR), the air parcel reaches its saturation point.
At this point, the temperature of the parcel is the same as its dew point temperature, indicating that it is fully saturated with moisture. Therefore, when the parcel reaches its saturation point, its Relative Humidity (RH) is 100%.
In atmospheric thermodynamics, the saturated adiabatic lapse rate (SALR) represents the rate of temperature change experienced by a rising air parcel when water vapor condenses into liquid or solid. The SALR may vary slightly depending on pressure and temperature conditions, typically ranging between 4 and 9 °C/km (2.2 and 4.9 °F/1000 ft).
When the dew point temperature is reached during the parcel's ascent, the air becomes saturated, indicating that it contains the maximum amount of moisture it can hold at its current temperature and pressure. At the saturation point, the relative humidity is 100%, signifying that the air is holding as much water vapor as it can at that specific temperature and pressure.
Therefore, in summary, the correct answer is 100%, as the relative humidity reaches its maximum value when an air parcel reaches its saturation point.
Learn more about environmental
https://brainly.com/question/21976584
#SPJ11
An 80 kg man jumps down to a concrete patio from a window ledge only 0.50 m above the ground. He neglects to bend his knees on landing, so that his motion is arrested in a distance of 2.9 cm, What is the average acceleration of the man from the time his feet first touch the patio to the time he is brought fully to rest? With what force does this jump jar his bone structure?
Answer:
What is the average acceleration of the man from the time his feet first touch the patio to the time he is brought fully to rest?
168.97m/s/s
With what force does this jump jar his bone structure?
14301.6N
Explanation:
What is the average acceleration of the man from the time his feet first touch the patio to the time he is brought fully to rest?
(Note that to solve this question you need to know and use the third equation of motion, v²=u²+2as, where v is final velocity, u is initial velocity, a is acceleration, and s is displacement.)
First the man drops 0.5m to the patio, and then it takes 2.9cm to fully stop. Let's look at the first half of this motion, from when he drops to when he first strikes the patio, but before he fully stops:
He drops to the patio, he doesn't jump with any momentum, so we can deduce his initial velocity (u) is 0m/s. The acceleration is due to gravity, so we take 'a' to be 9.8m/s/s, and the window is 0.5m above ground so s is 0.5. Subbing these in we get:
v²=u²+2as
v²=0²+2(9.8)(0.5)=9.8
v=3.13m/s, so the man strikes the patio at 3.13m/s
Now let's look at the part from when he first strikes the patio to when he fully comes to rest. He strikes the patio at 3.13m/s as we just figured out, so his initial velocity for this part is 3.13. We're told it takes 2.9cm to stop fully, so now s is 0.029. And if he's coming to a full rest, his final velocity will be 0. Subbing these in we get:
v²=u²+2as
0²=3.13²+2a(0.029)
0=9.8+0.058a
a=-9.8/0.085= -168.97m/s/s (value is neg because he comes to rest)
So the average acceleration is 168.97m/s/s
With what force does this jump jar his bone structure?
For this question we need to use Newton’s second law, F = ma + mg, where F is force, m is mass, a is acceleration and g is gravity:
F = ma + mg
F = m(a+g)
F = 80(168.97+9.8)=80(178.77)=14301.6
So the force exerted is 14301.6N
A = 10x - 2y B = 5x + 4y C=2A + B What is the magnitude of the vector C? Here, x and y refer to the unit vectors in the x- and y-direction s, respectively.
Therefore, the magnitude of vector C is 25.
Given:A = 10x - 2yB = 5x + 4yC=2A + BNow we have to calculate the magnitude of vector C.Let's calculate each part of the vector C first;2A = 2(10x-2y) = 20x - 4yB = 5x + 4yC = 2A + B= (20x-4y)+(5x+4y)=25xNow we can calculate the magnitude of vector C by using the formula;|C| = √(Cx²+Cy²+Cz²)Here, we only have two dimensions, so the formula becomes;|C| = √(Cx²+Cy²)|C| = √(25²) = 25. Therefore, the magnitude of vector C is 25.
To know more about vector visit:
https://brainly.com/question/18441260
#SPJ11