Answer:
B)
Explanation:
Scientific method- a method of procedure that has characterized natural science since the 17th century, consisting in systematic observation, measurement, and experiment, and the formulation, testing, and modification of hypotheses.
in this, the scientist had to test their theories to find a solution to their problem.
Describe an experiment to show that the force pulling an object increase
with the increase in the mass of the object.
Answer:
"Acceleration due to gravity" whereby Force and Mass are directly proportional
Explanation:
F=ma
Answer:
just use the magnet experience
Explanation:
it shows how force pulling an object increase
with the increase in the mass of the object.
Isaac Newton's first law of motion states?
Answer:
His first law states that every object will remain at rest or in uniform motion in a straight line unless compelled to change its state by the action of an external force. In other words its inertia.
Explanation:
Newtons first law of motion states that"A body will continue to its state of rest or motion unless external force acted upon it.
A parallel circuit containing two bulbs and a bell has three paths for the current flow. If the first bulb in the circuit burns out, what effect will it have on the other loads in the circuit?
A. The other bulb will go out, but the bell will continue to work.
B. The other bulb will remain lit, but the bell will no longer work.
C. The other loads will not be affected.
D. All the other devices will stop working.
Answer:
C
Explanation:
Since the circuit is in parallel there will be no effect on the other loads.
. Reem took a wire of length 10 cm. Her friend Nain took a wire of 5 cm of the same material and thickness both of them connected with wires as shown in the circuit given in figure. The current flowing in both the circuits is the same. (a) Will the heat produced in both the cases be equal? Explain.
Given :
Reem took a wire of length 10 cm. Her friend Nain took a wire of 5 cm of the same material and thickness both of them connected with wires as shown in the circuit given in figure. The current flowing in both the circuits is the same.
To Find :
Will the heat produced in both the cases be equal.
Solution :
Heat released is given by :
H = i²Rt
Here, R is resistance and is given by :
[tex]R = \dfrac{\rho L}{A}[/tex]
So,
[tex]H = i^2\times \dfrac{\rho L}{A} t\\\\H = \dfrac{i^2\rho Lt}{A}[/tex]
Now, in the question every thing is constant except for the length of the wire and from above equation heat is directly proportional to the length of the wire.
So, heat produced by Reem's wire is more than Nain one.
Hence, this is the required solution.
Mechanical weathering does not change a rock's
Answer:
composition
Explanation:
With mechanical weathering, the composition of the rocks does not change. ... This process can cause the rock to again break down into smaller pieces.
Answer:
composition
Explanation:
what does acromyn BMI stand for
Answer:
Body Mass Index
Explanation:
what disadvantages does a conveyor belt have?
Answer:
Some of the disadvantages are: The normal design of a belt conveyor is opened. If your product needs to be contained, covers and or drip pans can become expensive and cumbersome. If the material is sticky, belt cleaning can be difficult and generally not very successful.
Explanation:
A baseball is thrown towards home plate. It takes 3.4 seconds for the ball to reach the catcher's glove from the pitcher's glove and reaches a maximum velocity of 90m/s. What is the ball's acceleration?
Answer:
57
Explanation:
1. What does a negative value mean? Can distance be negative? Explain.
Answer: A negative value is values and frequency for the data you are analyzing had enough negative values. Sometimes distance can be negative. For example, when you are in the pool, underwater, or standing left from the middle of origin.
Explanation:
A box of mass m is pushed at an angle 0 by a force Fp along a frictionless surface. The box travels to right with acceleration a. What is the mass of the box?
Answer:
m = FpCos0 / a
Explanation:
it just is
A box of mass m is pulled at an angle θ by a force Fp along a frictionless surface. The box travels to the right with acceleration a
What is the mass m of the box?
Answer: m = FpCos0/a
A wave had a frequency of 5 hertz and a speed of 25 m/s. What is the wavelength of the wave
Heya!!
For calculate wavelength, lets applicate formula:
[tex]\boxed{\lambda = V/f}[/tex]
Δ Being Δ
f = Frequency = 5 Hz
v = Velocity = 25 m/s
[tex]\lambda[/tex] = Wavelenght = ?
⇒ Let's replace according the formula:
[tex]\boxed{\lambda = 25\ m/s / 5\ Hz }[/tex]
⇒ Resolving
[tex]\boxed{\lambda = 5\ m}[/tex]
Result:
The wavelength is 5 meters.
Good Luck!!
The wavelength of the wave is 5 meters.
Given the following data:
Frequency = 25 HertzSpeed = 25 m/s.To find the wavelength of the wave:
Mathematically, the wavelength of a waveform is calculated by using the formula;
[tex]Wavelength = \frac{Speed}{Frequency}[/tex]
Substituting the given parameters into the formula, we have;
[tex]Wavelength = \frac{25}{5}[/tex]
Wavelength = 5 meters.
Therefore, the wavelength of the wave is 5 meters.
Read more: https://brainly.com/question/14708169
A thin hoop with a mass of 5.0 kg rotates about a perpendicular axis through its center. A force F is exerted tangentially to the hoop. If the hoop’s radius is 2.0 m and it is rotating with an angular acceleration of 2.5 rad/s2, calculate the magnitude of F.
a. 35 N
a. 20 N
c. 25 N
d. 8 N
Given :
Thin hoop with a mass of 5.0 kg rotates about a perpendicular axis through its center.
A force F is exerted tangentially to the hoop. If the hoop’s radius is 2.0 m and it is rotating with an angular acceleration of 2.5 rad/s².
To Find :
The magnitude of F.
Solution :
Torque on hoop is given by :
[tex]\tau =F\times R\\\\I\alpha = FR\\\\MR^2\alpha = FR\\\\F = MR\alpha[/tex]( Moment of Inertia of hoop is MR² )
Putting value of M, R and α in above equation, we get :
[tex]F=5\times 2\times 2.5\ N\\\\F = 25 \ N[/tex]
Therefore, the magnitude of force F is 25 N.
Hence, this is the required solution.
During a lab you combined 5g of sodium bicarbonate and 10g of vinegar to produce sodium acetate, water, and carbon dioxide. After the reaction the contents of the beaker only weighed 14.5g. How much of the reactants were converted into carbon dioxide?
Answer:
Explanation:
Na₂CO₃ + CH₃COOH = CH₃COONa + CO₂ + H₂O .
1 mole 1 mole
mol weight of sodium carbonate = 106
mol weight of acetic acid = 60
5 g of sodium carbonate = 5 / 106 = .047 moles
10 g of acetic acid = 10 / 60 = .167 moles
sodium carbonate is the limiting reagent
.047 moles will react with .047 moles of acetic acid to give products .
grams of acetic acid reacted = .047 x 60 = 2.82 gram
grams of sodium carbonate reacted = 5 grams .
A spring compresses 0.8 m when the 800 kg crate of llamas slides down and hits it. Ignore friction and find the spring constant of the spring. The ramp is at a 47° angle.
Answer:
7167.27N/m
Explanation:
To get the force constant k, we will use the formula;
F = kx where
F is the force acting on the object down the plane
k is the spring constant
x is the extension
The force acting down the ramp us F = Wsintheta. The formula will become;
Wsintheta = kx
mgsintheta = kx
K = mgsintheta/x
K = (800)(9.8)sin47°/0.8
K= 7840sin47°/0.8
K = 5733.81/0.8
K = 7167.27N/m
Hence the spring constant of the spring is 7167.27N/m
A 100 kg cart on a roller coaster has 1800J of kinetic energy. How fast is it going?
KE= 1/2mv2
Answer:
the speed is equal to 6 m/s
Explanation:
Match each term to its definition.
Problem 1
You push your square space cow, mass 5 kg, with a force of 10 N. what will be the acceleration of your space cow?
Answer:
2 m/s²Explanation:
The acceleration of an object given it's mass and the force acting on it can be found by using the formula
[tex]a = \frac{f}{m} \\ [/tex]
f is the force
m is the mass
From the question we have
[tex]a = \frac{10}{5} \\ [/tex]
We have the final answer as
2 m/s²Hope this helps you
Question 7 of 20 A permanent magnet is placed in a coil of wire. If there is no electric current in the wire, which statement must be true? A. The magnet is moving relative to the wire. B. The magnet is not moving relative to the wire. C. The magnet is longer than the coil of wire. D. The magnet is shorter than the coil of wire.
Answer:
the magnet is not moving relative to the wire so B
Explanation:
The magnet is not moving relative to the wire if, A permanent magnet is placed in a coil of wire, If there is no electric current in the wire so, option B is correct.
What is current?Electric current is a term used to describe how much electricity flows across a circuit and how it flows in an electronic circuit. Amperes are used to measure it (A). The more electricity flowing across the circuit, the higher the ampere value.
When current flows through a coil of wire, it transforms into an electromagnet. The coil spins as a result of the electromagnet's interaction with a permanent magnet.
An electromagnet is created when current passes through a coil of wire. Because of the electromagnet's interaction with a permanent magnet, the coil spins.
Thus, The magnet is not moving relative to the wire.
To know more about current:
https://brainly.com/question/4289257
#SPJ2
Which change to an object would double its kinetic energy?
A. Increasing its mass to twice its original value
B. Increasing its mass to four times its original value
C. Increasing its velocity to four times its original value
D. Increasing its velocity to twice its original value
Clouds are forming along the front because the rising air is
A) contracting and warming, causing
evaporation
B) contracting and cooling, causing evaporation
C) expanding and warming, causing condensation
D) expanding and cooling, causing condensation
Answer:
D
Explanation:
The water vapor rises in the air. It starts to expand while cooling the higher it gets in the atmosphere. This causes condensation.
Clouds are forming along the front because the rising air is expanding and cooling, causing condensation (Option D).
Cloud formation occurs when water vapor cools and condenses to form liquid water droplets or solid ice crystals.In a cloud, liquid water droplets are formed at temperatures higher than 0 Celsius degrees, while solid ice crystals are formed at temperatures lesser than 0 Celsius degrees.In consequence, during cloud formation, the excess amount changes from water vapor (gas) into a liquid (water droplets) or solid (ice).In conclusion, clouds are forming along the front because the rising air is expanding and cooling, causing condensation (Option D).
Learn more in:
https://brainly.com/question/1242352
Plss help
The above person is in an elevator as it accelerates
upward. What do they feel?
a. Heavier than normal. c. The same weight as
normal.
b. Lighter than normal. d. Scared to be in an elevator
with no door.
Answer:
b
Explanation:
imagine urself on an elevator dont you feel lighter
What occurs when the moon blocks the view of the sun
Neap tide
Spring tide
Solar eclipse
Lunar eclipse
Answer:
solar eclipse
Explanation:
because at that time, the moon completely covers the path and casts its shadow on earth because it is present between sun and earth's path. so, solar eclipse occurs.
hope it helps :)
Answer:solar eclipse
Explanation:
Top one is right <3
Which of the following diagrams best represents the gravitational force W. the frictional force f, and the normal force N that act on the block?
It's D.
Weight always points downward.
The normal force always points perpendicular to the surface.
Friction opposes motion, so it points in the direction opposite the direction in which the block is moving.
An 1850 kg car is moving to the right at a constant speed of 1.44 m/s.
a. What is the net force on the car?
b. What would be the net force on the car if it were moving to the left?
Answer:
Read explanation and see if that helps
Explanation:
Newton's second law of motion states that the force on an object is given by f = ma. since the car is moving to the right at a constant speed of 1.44 m/s the acceleration a = 0. this means that there is no net force driving the car.
direction doesnt matter as long as the car is moving in a straight line at a constant speed the force will always be zero
The acceleration of the car in both directions (right and left) is zero.
The given parameters;
mass of the car, m = 1850 kgspeed of the car, v = 1.44 m/sThe net force on the car is calculated by applying Newton's second law of motion as shown below;
F = ma
where;
a is the acceleration of the carAt constant speed, the acceleration of the car will be zero
F = m(a)
F m(0)
F = 0
When the car is moving left, the net force is also zero since the acceleration is zero.
Thus, the acceleration of the car in both directions (right and left) is zero.
Learn more here:https://brainly.com/question/19887955
At which position is the roller coaster car's amount of potential energy about equal to the amount of kinetic energy?
Answer:
The mass of the cars and people and the height of the track where the cars are located determine the potential energy in the system. Potential energy depends on an object’s mass and height and the gravitational pull on the object. A change in gravity would result in a change in potential energy. For example, if the track were located on the Moon instead of Earth, the potential energy would be different.
Explanation:
You launch a model rocket that has a mass of 1.5 kg. At a height of 300 m, it is traveling at 125 m/s. What is it's kinetic energy at this point
Answer:
KE = 11,719 J
Explanation:
KE = ½ mv²
KE = ½ (1.5 kg) (125 m/s)²
KE = 11,719 J
Answer: 11,719 J
Explanation:
just did it on a.p.e.x
A hockey puck with a mass of 0.18 kg is at rest on the horizontal frictionless surface of the rink. A
player applies a horizontal force of 0.5 N to the puck. Find the speed and the traveled distance 5s
later.
Given :
A hockey puck with a mass of 0.18 kg is at rest on the horizontal frictionless surface of the rink.
A player applies a horizontal force of 0.5 N to the puck.
To Find :
The speed and the traveled distance 5s later.
Solution :
Acceleration is :
a = F/m
a = 0.5/0.18 = 2.78 m/s² .
Now, velocity after 5 seconds is given by :
v = 0 + 2.78×5 m/s
v = 13.9 m/s
Also, distance travelled :
[tex]d = \dfrac{v^2-u^2}{2a}\\\\d = \dfrac{13.9^2-0^2}{2\times 2.78}\\\\d = 34.75 \ m[/tex]
Therefore, speed and the traveled distance 5 s later is 13.9 m/s and 34.75 m.
Definition: This is a drawing showing the direction and magnitude of all forces acting on a body.
Answer:
Free body diagram
The ball is displaced to the left and then oscillates backwards and forwards between the two plates. The ball touches a plate once every 0.05 s. Every time it touches a plate, a charge of 2.8 × 10−8 C (0.000 000 028 C) is transferred. Calculate the average current produced by the repeated transfer of charge.
Answer:
Average current produced by the repeated transfer of charge is 5.6 × 10⁻⁷ ampere
Explanation:
The formula to be used here is
Q = It
where Q is the quantity of electricity and it is measured coulombs (C); 2.8 × 10⁻⁸ C or 0.000000028 C
I is current and it is measured in ampere (amps or A); unknown
t is time and it is measured in seconds (s); 0.05 s
Since, average current is what is unknown
I =Q/t
I = 0.000000028/0.05
I = 5.6 × 10⁻⁷ A
Average current produced by the repeated transfer of charge is 5.6 × 10⁻⁷ ampere
How is fishpond raising affected by global climate change?
Answer:
It creates bad air so that’s like air pollution I guess
Explanation: