The frequency the remote-pilot should use to monitor air traffic near an uncontrolled airport is the Common Traffic Advisory Frequency (CTAF).
What is air traffic?
Air traffic is the movement of aircrafts such as planes and helicopters in a certain area. This may include both civilian and military aircrafts. Air traffic is managed by air traffic controllers who are responsible for ensuring the safety of aircrafts by providing directions and instructions on the ground and in the air. They also inform pilots about the current weather conditions and ensure the proper separation of aircrafts from each other. Air traffic controllers must constantly monitor the positions and movements of aircrafts in their airspace and keep track of all the data related to their flight paths.
The CTAF is a frequency used by pilots and air traffic control to exchange information about aircraft operating in the vicinity of an airport.
To learn more about air traffic
https://brainly.com/question/29773821
#SPJ4
The calculated load for a 3-phase, 240-volt load is 196 amperes. The installation consists of three single insulated conductors in electrical metallic tubing, Type EMT. What size RHW copper conductors are needed
The size of RHW copper conductors needed for this 3-phase, 240-volt load is 4/10 AWG.
What is copper conductors?Copper conductors are electrical wires composed of copper that are used to carry electrical currents. They are used in a variety of applications, including power generation and transmission, electronics, telecommunications, and consumer products. Copper is an ideal material for electrical conductors because it is highly conductive, durable, and cost-effective. Copper conductors are available in a range of sizes and shapes and are used in both residential and commercial settings.
This is based on the National Electrical Code (NEC) Table 310.15(B)(16), which states that the minimum size for a 196 ampere load is 4/10 AWG for three insulated conductors in an EMT conduit.
To learn more about copper conductors
https://brainly.com/question/14941254
#SPJ4
A stainless steel vessel holds 5.4 liters of milk. One-third of the milk is given to a cat. After some water is added to the milk that remains, its volume becomes 1.25 as much as it was before the water was added. If one-third of this diluted milk is given to three kittens, how much milk does the vessel hold now
The vessel now holds 4.05 liters of milk, after one-third of this diluted milk is given to three kittens
A stainless steel vessel holds 5.4 liters of milk. One-third of the milk is given to a cat. After some water is added to the milk that remains, its volume becomes 1.25 as much as it was before the water was added.
Before the water was added, the vessel held 5.4 liters of milk. After one-third (1.8 liters) was given to the cat, there was 3.6 liters of milk remaining in the vessel.
After adding water, the volume of the milk increased by a factor of 1.25, so the vessel now holds 4.5 liters (3.6 x 1.25) of diluted milk. Finally, one-third (1.5 liters) of this diluted milk is given to the three kittens, leaving 4.05 liters of milk in the vessel.
For more questions like Diluted milk click the link below:
https://brainly.com/question/10847815
#SPJ4
Which of the following is a good technique for building safer structures in an earthquake zone? a. Place shock absorbers on the tops of buildings to add stability. b. Use wood-frame construction. c. Use unreinforced walls so the walls can sway. d. Use concrete-block construction.
The following is a good technique for building safer structures in an earthquake zone is to use concrete-block construction.
What is an earthquake zone?
An earthquake zone is an area that is prone to frequent seismic activity. These zones are commonly located near active fault lines, where the Earth's tectonic plates constantly move. Earthquakes can cause significant damage to the local area, so it is important to be aware of the potential dangers of living in a seismically active region. In order to assess the risk, geologists and seismologists will measure the frequency and intensity of past earthquakes to determine the potential hazard posed by a particular area. Earthquake zones can also be classified according to their potential for danger, with some areas having a higher risk than others. It is important to remember that earthquakes can occur anywhere and that safety precautions should always be taken when living in a seismically active region.
To learn more about earthquake zone
https://brainly.com/question/17053867
#SPJ4
A flow i decribed by velocity field V=ayibxj where a = 2 (m/) and b = 1 (1/) , coordinate are meaured in meter. A) Obtain the equation for the treamline paing through the point (2,5). B) At t=2 , what are the coordinate of the particle that paed through point (0,4) at t=0. C) At t=3 , what are the coordinate of the particle that paed through point (1,4. 25) 2 econd earlier
The equation for the streamline passing through point (2,5) is y-5=b/a(x-2).
What is streamline?Streamlining is a process of simplifying or improving a process or system to increase efficiency, reduce complexity, and reduce costs. It can involve reorganizing, restructuring, rearranging, or redefining a system, procedure, or process to make it more efficient and productive.
B) At t=2, the coordinate of the particle that passed through point (0,4) at t=0 is (6,7). This is because since the velocity field is V = ayibxj, the particle will experience a displacement of 2a in the x-direction and 2b in the y-direction in the span of 2 seconds. Thus, the displacement of the particle is (2a,2b) = (4,2). Adding this to the initial position (0,4), the new position of the particle is (4,6).
C) At t=3, the coordinate of the particle that passed through point (1,4.25) 2 seconds earlier is (7.25,6.25). This is because since the velocity field is V = ayibxj, the particle will experience a displacement of 3a in the x-direction and 3b in the y-direction in the span of 3 seconds. Thus, the displacement of the particle is (3a, 3b) = (6,3). Adding this to the initial position (1,4.25), the new position of the particle is (7,7.25).
To learn more about streamline
https://brainly.com/question/22453879
#SPJ4
A property's roof is twenty years old and has not been replaced. This condition would most likely be considered to be an example of
A property's roof is twenty years old and has not been replaced. This condition would most likely be considered to be an example of curable physical deterioration.
What is Curable physical deterioration?
Curable deterioration is a type of deterioration that can be cured economically. The economic feasibility of a property is indicated if the increase in value exceeds or is equal to the anticipated cost of repairing the property. The cost of replacing or restoring the item is used as a reasonable measure of curable deterioration.
Estimating the value of items that need to be repaired, such as window replacements, repainting, weatherstripping, roof repair, loose tile fixing, faulty wiring, and heating or cooling system repairs, is part of measuring curable deterioration.
Only include the items listed above if the increase in property value will cover the cost of repairs. For example, if roof repair and loose tile repair are estimated to cost $8,000, a prospective buyer can reduce their offer price by the same amount to cover the cost of doing such repairs.
To learn more about roofs, visit: https://brainly.com/question/29517525
#SPJ4
B. Directions: For items 9-15, sequence the steps involved on how to accomplish
the form in order to acquire materials. Write letters a lo h on the blank, 'a' being the
first step, and so on. Do this in your Activity Notebook.
8. Write your name as requisitioner
9. List the cost per unit and the total cost.
10. Write the number of required materials.
11. List the unit of materials to be requisitioned.
12. Secure the approval of the supply officer.
13. Enumerate the materials with their description.
1. 4. State the name of the project and date when you requested for materials.
The letters A to H on the blank, 'A' being the first step, and so on is as follows:
8-F, 9-E, 10-B, 11-C, 12-G, 13.D 14.A
What is sequence?In mathematics, a sequence is an ordered list of objects where repetitions are allowed. It has members and is comparable to a set (also called elements, or terms). The number of elements determines the length of the sequence (possibly infinite). In contrast to a set, the same elements can appear multiple times in a sequence at different positions, and unlike a set, the order matters.
Formally, a sequence can be defined as a function from natural numbers (the positions of the sequence's elements) to the elements at each of those positions. You can think of an indexed family, which is a function from any index set, as a generalisation of the concept of a sequence.
Learn more about sequence
https://brainly.com/question/21961097
#SPJ4
The standard overload protection for a 2 hp, 115 V, single phase motor has a nameplate rating of 21.50 A shall not be rated greater than __________________ amperes.
The standard overload protection for a 2 hp, 115 V, single phase motor has a nameplate rating of 21.50 A shall not be rated greater than 21.50 A amperes.
What is motor?
Motor is an electro-mechanical device which converts electrical energy into mechanical energy. It is widely used in industrial and domestic applications to produce rotational motion for machines. Motors are available in a variety of sizes and types, ranging from small DC motors to large AC synchronous motors. Motors are used to power a wide range of machines, from small fans and pumps to large industrial machines such as elevators, cranes, and conveyors. Motors can be powered by electricity, batteries, or fuel, and can be used to move objects in different directions. Motor control systems can be used to control the speed and direction of a motor, allowing for precise and efficient control of a machine. Motors are essential components of modern machines and are used in a wide variety of devices such as electric vehicles, robots, and home appliances.
To learn more about motor
https://brainly.com/question/13002418
#SPJ4
round your answers to the nearest hundredths if needed -25+5s=8
Answer:
s = 6.6
-25 + 5 × 6.6 = 8
Just let me know if you need any more help.
What qualitative effect would you expect each of the following to have on the P50 of hemoglobin (5 pts) a) Increase in pH from 7.0 to 7.4 Answer ___
b) Increase in Pco2 from 25 mmHg to 35 mm Hg Answer___
c) Dissociation into monomer polypeptide chains Answer ____
d) Decrease in 2,3-BPG concentration from 8 mM to 4 mM in red cells Answer___
You would expect each of the following to have a lower p50 qualitative effect on hemoglobin (5 pts) a) Raising the pH from 7.0 to 7.4.
What does "qualitative influence" mean?On the forecasts, there is a "qualitative influence." Reliability and accuracy are two characteristics of forecasts. The dependability or accuracy of the forecasts may improve or worsen, depending on the qualitative effect.
What does a polypeptide protein's monomer look like?Acitric Acids As an illustration, amino acid monomers make up proteins. A functional protein is created by folding a chain of linked polypeptides into a three-dimensional (3D) structure.
To know more about qualitative effect on hemoglobin visit :-
https://brainly.com/question/30216819
#SPJ4
Find the time function corresponding to each of the following Laplace transforms using partial fraction expansions: (a) = F(s) = 1/s(s+1) (b) F(s) = 5/s(s+1)(s+5) (c) F(s) = 3s+2/s^2 + 2s + 10
The time function corresponding to each of the following Laplace transforms using partial fraction expansions will be:
(a) f(t) = e^(-t) + te^(-t)
(b) f(t) = 5e^(-t) + 5te^(-t) - 10e^(-5t)
(c) f(t) = 3e^(-t) + (2t+1)e^(-t) - 2e^(-2t) - 5te^(-2t)
What is fraction?
A fraction is a type of mathematical expression that represents a part of a whole. It is written as a ratio of two numbers, with a line separating them. For example, the fraction 1/2 represents one part of a whole that has been divided into two equal parts. Fractions are used to express amounts that are less than one, such as a half, a quarter, or a third. They can also be used to express amounts greater than one, such as two thirds, three quarters, or four fifths. Fractions are used in many different areas of mathematics, such as addition, subtraction, multiplication and division.
To learn more about fraction
https://brainly.com/question/20038994
#SPJ4
For the systems described by the following equations, with the input x (t) and output y(t), determine which of the systems are linear and which are nonlinear. Dy / dt + 2y (t) = x2 (t) dy / dt + 3ty (t) = t2 x (t) 3y (t) + 2 = x (t) dy / dt + y2 (t) = x (t) (dy / dt )2 + 2y (t) = x (t) dy / dt + (sin t) y (t) = dx / dt + 2x (i) dy / dt + 2y (t) = x (t) dx / dt y (t) = f 1 -infinity x (tau) d tau
The first equation is linear, the second equation is nonlinear, the third equation is nonlinear, the fourth equation is nonlinear, the fifth equation is nonlinear, and the sixth equation is nonlinear.
What is equation?
An equation is an expression that contains an equal sign and relates two or more mathematical quantities. It typically consists of constants, variables, and symbols, and can be written in different forms such as standard form, slope-intercept form, and factored form. Equations are used to describe relationships between variables, and they can be used to solve a wide range of problems, from basic arithmetic to advanced calculus and physics. Equations are also used to model real-world phenomena, such as electricity, kinematics, and quantum mechanics. By studying equations and their solutions, we can gain a deeper understanding of the physical world around us.
To learn more about equation
https://brainly.com/question/24179864
#SPJ4
increasing capacity just before a bottleneck operation will improve the output of the process.
a. true
b. false
Answer: true
Explanation: I haves
The section is experiencing a positive bending moment about the z-axis, where Mz = 1.13 kN-m. What is the resulting stress at the top and bottom surfaces? And are they in tension or compression?
The resulting stress at the top and bottom surfaces is 837.5 N/m^2 and -837.5 N/m^2, respectively. The top surface is in compression and the bottom surface is in tension.
What is stress?
Stress in engineering is the amount of force per unit area placed on a material or structure. It can be physical, or it can be psychological. Stress can be positive or negative. Positive stress can cause a material to become stronger, while negative stress can cause it to become weaker or even fail. Stress can also refer to the amount of strain a material must endure before it yields or breaks. Stress is measured in terms of pounds per square inch (psi) or newtons per square meter (N/m2). Stress analysis is important in engineering as it helps to identify potential failure points in a design, or to determine how much a material can handle before it breaks. Stress analysis is used to ensure the safety and integrity of products, structures, and machines.
To learn more about stress
https://brainly.com/question/13260444
#SPJ4
Tech A says that if you are unsure of what personal protective equipment (PPE) to use to perform a job, you should just use what is nearby. Tech B says that air tools are less likely to shock you than electrically powered tools. Who is correct
According to the question of personal protective equipment, tech B is correct.
What is personal protective equipment?
Personal Protective Equipment (PPE) is any equipment, clothing, or device designed for use on the body to protect the wearer from injury or infection. This can include items such as gloves, safety glasses, protective clothing, hard hats, respirators, and face masks. Proper use of PPE is important to help reduce the risk of exposure to hazardous materials and environments, as well as the spread of infection. PPE is most effective when used in combination with other safety measures, such as engineering controls, administrative controls, and good hygiene practices.
Air tools are powered by compressed air and are considered to be safer than electrically powered tools because they are not connected to an electrical source.
To learn more about personal protective equipment
https://brainly.com/question/30003482
#SPJ4
Gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively. If the shaft is made of steel with the allowable shear stress of tau_allow = 75 MPa, and the relative angle of twist between any two gears cannot exceed 0.05 rad. determine the required minimum diameter d of the shaft to the nearest millimeter. The shaft is rotating at 600 rpm.
Using the formula of shear stress, the minimum required diameter is 0.81mm
What is Shear StressShear stress is a force that causes two objects to slide past each other in opposite directions. It is the force per unit area of the surface on which the force is applied. Shear stress is often caused by two objects rubbing against each other, such as a car tire sliding on the road. It can also be caused by wind, gravity, or other forces.
The shear stress on the shaft can be calculated using the formula:
τ(allow) = P/(2*π*d*J)
where P is the total power transferred by the shaft, d is the diameter of the shaft, and J is the polar moment of inertia.
J = π*d⁴/32
Substituting the given values,
τ(allow) = (15 + 6 + 4 + 5)/(2*π*d*π*d⁴/32)
d = √[32*(15 + 6 + 4 + 5)/(τ(allow)*2*π²)]
d = √[32*(30)/(75*2*π²)]
d = 0.81mm
The minimum required diameter of the shaft is 0.81 mm to the nearest millimeter.
Learn more shear stress here;
https://brainly.com/question/13670232
#SPJ1
Before you can take a lesson exam, you must:
A. Complete all required laboratory exercises.
OB. Listen to all of the audio in the lesson.
C. Review all materials in the course Library.
D. None of these.
You must listen to all of the lesson's audio before you can take the exam. This is the appropriate assertion.
What purpose does a laboratory exercise serve?Students will be able to build deeper and longer lasting knowledge and a deeper comprehension of the scientific method through carefully planned laboratory exercises that emphasize inquiry-based or problem-based learning with attention to active learning under appropriate supervision.
What advantages does audio learning offer?Supporters of this method of learning assert that learning by ear enables one to be adaptable when carrying out a variety of jobs. This is due to the fact that information can be processed without the need of hands or eyes by simply listening to audio recordings.
To learn more about laboratory exercise visit:
brainly.com/question/26264658
#SPJ1
Me in a good way what is 16÷ 4743
Answer:
0.00337339236
Answer:
Hey there! 16 divided by 4743 is approximately equal to 0.003366. This means that if you take 16 and divide it by 4743, the result will be a number that is very close to 0.003366. This division problem can be written as the fraction 16/4743, or as the decimal 0.003366.
________________________________________________________
What are some common mistakes to avoid when solving division problems?Some common mistakes to avoid when solving division problems include forgetting to carry the remainder, failing to check for divisibility, and mixing up the order of the dividend and the divisor. It is also important to pay attention to the units of measurement and to ensure that the units in the dividend and the divisor are compatible.
What are some strategies for solving division problems with large numbers?Some strategies for solving division problems with large numbers include using place value to break down the numbers into smaller units, using long division or a calculator to perform the division, and using estimation to check the reasonableness of the answer. It can also be helpful to use mental math techniques, such as rounding, to simplify the division problem. Other strategies might include using division to find the prime factorization of a number or to identify common factors or multiples.
Classify the variable as nominal-level, ordinal-level, interval-level, or ratio-level measurement. Number of gallons of water in a swimming pool
The number of gallons in a swimming pool in the given question can be classified as a ratio level measurement.
What is ratio level measurement?The highest of the four hierarchical levels of measurement is the ratio level measurement. Data recording accuracy is determined by the levels or scales of measurement. The measurement becomes more difficult as the level increases.
The features of the other 3 levels are all present in the ratio level. At the ratio level, values can take on a true zero, be categorised, ordered, have equal intervals, and more.
While interval and ratio variables are quantitative variables, nominal and ordinal variables fall under the category of categorical variables. Quantitative data allows for a much wider range of statistical tests than categorical data.
Learn more about ratio level measurement
https://brainly.com/question/14739567
#SPJ4
Which of the following steps should a high school teacher take first when introducing procedures at the beginning of the year: A. Explaining the details of the procedures
B. Correcting misunderstandings about the procedures
C. Reinforcing effective use of the procedures
D. Practicing the procedures regularly with the class
Option A is correct because the details of the procedures should be explained before they are practised at this age level.
Options B, C, and D are incorrect because, while these steps are necessary, students must first understand the procedures.
How to teach procedures to your students?
The key to making your classroom run smoothly and efficiently is to teach procedures. If you take the time to teach your class how to do things, I guarantee you will have more time to focus on academics in the long run.
STEP 1 – PROCEDURES START WITH YOU
Before you can teach your students procedures, you must first envision how you want your classroom to look, sound, and feel on a daily basis. This means that you must consider these issues before the start of the school year.
STEP 2 – PUT YOUR PROCEDURES INTO SIMPLE STEPS
Once you've decided on the procedure that will get you to your ideal classroom, it's time to break it down into simple, easy-to-follow steps. When you do this, keep your students in mind. The language and number of steps will differ if you teach Pre-K or Kindergarten versus 3rd, 4th, or 5th grades. I've always found the K.I.S.S. method to be effective. Keep it as simple as possible.
STEP 3 – TEACH THE PROCEDURES
Introduce the need for procedureThe procedureModel the procedurePractice the procedurePut the procedure into actionTo learn more about how to write description and procedures, visit: https://brainly.com/question/28717367
#SPJ4
Which of the following is NOT a factor in the quality of digital video? a.- frame rate and resolution c. compression technique b. memory technology in your camera de color and bit depth
The choices that best describe the process of digitization are: Option A: binary-stored video. Option C converts analog video to digital video.
Information transformation into a digital format is referred to as digitization. Be aware that in this format, data is organized into discrete units of data called bits. As a result, the following options best represent the digitization process: Option A: binary-stored video. Option C converts analog video to digital video. This is due to the fact that digital video is a key technology for both video conferencing and video messaging in addition to being a key technology for digital television. This was demonstrated by its use in messaging apps for confidential conversations and for hosting virtual conferences for business meetings amongst personnel.
Learn more about Digitization here:
https://brainly.com/question/28368732
#SPJ4
Look at the following statement. while (++x < 10) Which operator is used first? ++ Neither. The expression is invalid. O both ++ and < operators are used at the same time.
A "While" Loop is used to repeatedly execute a particular block of code until a condition is met.
The responses to the questions are listed below. The operation that determines whether the condition x 10 is true is assessed first because the operator is used first. The reason for this is that we use the post increment operator for x. As a result, x is first used for the operation we are performing before being raised by 1. According to semantics, the variable's value is increased by 1 by both prefix and postfix ++. The result of the operator is the NEW/CURRENT value stored in the variable if the ++ is placed before the variable (a prefix operator); the result of the operator is the value stored in the variable if the ++ is written after the variable (a postfix operator).
Learn more about Operator here:
https://brainly.com/question/30115441
#SPJ4
Problem 6. Rods AC and BC are used to suspend the 200-kg mass. If each rod is made of a material for which the average normal stress can not exceed 150 MPa, determine the minimum required diameter of each rod to the nearest mm
The minimum required diameter should be 5 mm for each rod.
What is stress?In physics, stress describes the force acting on a material's unit area. A specific body can become deformed under stress. Strain is the term for the impact that stress has on the body. To restore an object to its original form and size, an opposing force known as a restoring force is produced inside the object. The symbol "σ" stands for stress, which is a tangible quantity. N/m2 is the stress unit in the SI system.
Strength is an object's capacity to withstand the applied stress to the fullest extent possible. Physics distinguishes between two types of stress: Tangential or Shearing Stress and Normal Stress based on the direction of the deforming forces that act on a body.
πd²[tex]_{min}[/tex]/4 = 1962/150
d[tex]_{min}[/tex] = [tex]$ \sqrt{\frac{4 \times 1962}{\Pi \times 150} }[/tex]
d[tex]_{min}[/tex] = 4.081
As, 4 < 4.081 < 5,
The minimum required diameter should be 5 mm for each rod.
Learn more about stress
https://brainly.com/question/25632718
#SPJ4
A stall occurs when the smooth airflow over the unmanned airplane`s wing is disrupted, and the lift degenerates rapidly. This is caused when the wing
A stall happens when the smooth airflow over the unmanned airplane`s wing is disrupted, and the lift degenerates rapidly. This is caused when the wing "exceeds its critical angle of attack."
The angle of attack refers to the angle at which the airplane's wing meets the air that is flowing over it. When an airplane actually is taking off, it is lifting the nose up into the air. And, if that nose continues to rise ultimately it reaches a point where the air is not able to smoothly flow over the wing, causing the airplane to drop. And, this is the point when the airplane exceeds its critical angle of attack.
Exceeding the critical angle of attack is known to be a stall. This has no concern with the engine stalling, it just concerns with the wings not producing enough lift to keep the airplane in the air.
You can learn more about critical angle of attack at
https://brainly.com/question/13209325
#SPJ
raw sugar cane is taken into a process to create sugar, which is essentially sucrose. the raw cane is approximately 16% sucrose, 63% water, and the rest fiber by mass. juice from the cane is extracted by passing the cane through a series of crushers. about 5% extra mass of water is added to the sugar cane prior to this step to help in the extraction process. the crushed cane and liquid juice is sent to a filter press that creates a cake that contains 4% of the weight of the cane juice, which has a composition similar to the overall non-fiber content of the raw cane. the filtrate is sent to an evaporator where enough water is evaporated to obtain a pale yellow juice that is 41% water. a
The process of creating sugar from raw sugar cane involves several steps. First, the raw cane is passed through a series of crushers to extract the juice from the cane.
What is crusher?A crusher is a machine designed to reduce large rocks into smaller rocks, gravel, or rock dust.
This step also adds about 5% extra mass of water to the sugar cane to help with the extraction process. The crushed cane and liquid juice are then sent to a filter press, which creates a cake containing 4% of the weight of the cane juice. This cake has a composition similar to the overall non-fiber content of the raw cane. The filtrate is then sent to an evaporator, where enough water is evaporated to obtain a pale yellow juice that is 41% water. Finally, the liquid is crystallized to produce sugar crystals, which are typically about 99.8% sucrose.
To learn more about crusher
https://brainly.com/question/15352898
#SPJ4
A 2 HP, 120 V, single phase motor requires a _________________________ inverse time circuit breaker branch circuit short circuit and ground fault protective device. The motor has a nameplate FLC of 22.1 amperes.
A 2 HP, 120 V, single phase motor requires a 20 ampere inverse time circuit breaker branch circuit short circuit and ground fault protective device.
What is circuit?
A circuit is an electrical path between two or more points that allow electricity to flow. It consists of various components like resistors, capacitors, transistors, diodes, and wires. Each component serves as a building block to create a functioning circuit. Circuits are used to control and direct electricity to power a variety of devices like computers, televisions, radios, and more. They are at the heart of any electrical system, from the most simple to the most complex. By properly combining the components in a circuit, electricity can be directed to flow in the desired manner and perform the required tasks. Circuit design is an important engineering field and can be used to create many practical applications.
To learn more about circuit
https://brainly.com/question/30018555
#SPJ4
gearbox design calculation
Answer:Gearbox design calculations involve a variety of factors, including the type of gearbox, the size and type of gears, the torque and speed requirements, the materials used, and the environmental conditions. The calculations also involve the selection of the appropriate gear ratios, the selection of the appropriate bearings, and the selection of the appropriate lubrication system. Additionally, the calculations must take into account the safety and reliability of the gearbox.
Explanation:
You are tasked with mapping a drive within the Command Prompt to a share named AlbaLonga on a server named Romulus. Which of the following is the correct syntax?
A. net use //AlbaLonga./Romulus
B. http://Romulus/AlbaLonga
C. net use \\Romulus\AlbaLonga
D. ipp://Romulus.com/AlbaLonga
According to the question, net use \\Romulus\AlbaLonga is the correct syntax.
What is syntax?
Syntax is the set of rules and principles that govern the structure of sentences in a given language. It is a component of grammar that focuses on the arrangement of words and phrases to form correct sentences. Syntax helps to determine the meaning of a sentence and provides clarity for the reader. Syntax also plays an important role in writing, as it helps to create coherent and effective sentences that convey the right message. Syntax is a complex subject and involves the use of a variety of terms such as syntax, morphology, semantics, and pragmatics. Syntax also includes the use of punctuation and other stylistic devices. By understanding syntax, one can learn how to properly construct sentences, enabling them to communicate effectively in writing.
To learn more about syntax
https://brainly.com/question/14398309
#SPJ4
A(n) _________ is a set of permissions that is attached to an object.
a. access control list (ACL)
b. Subject Access Entity (SAE)
c. object modifier
d. security entry designator
Part A
Determine the force in member DE of the truss, and state if the member is in tension or compression. Take F1 = 564 N , F2 = 905 N .
(Figure 1)
Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.
Part B
Determine the forces in members DC and CB of the truss, and state if the members are in tension or compression.
Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.
Part C
Determine the force in member CE of the truss, and state if the member is in tension or compression.
Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.
Part D
Determine the force in member EB of the truss, and state if the member is in tension or compression.
Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.
Part E
Determine the force in member EA of the truss, and state if the member is in tension or compression.
Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.
What is the difference between cinema and theatre ?? I want the difference
Answer:
The main difference between theatre and cinema is that theatre involves live performances like plays, opera, ballet, and musical theatre, while cinema involves films.
Theatre is a building or outdoor area that houses dramatic presentations, and stage entertainments. In British English, cinema refers to a building that contains an auditorium for viewing films – this is equivalent for movie theatre in American English.
Explanation:
Similarities between theatre and movies
Both movies and theatre focus on social evils and problems and represent them to society through play and cinema. In both, the purpose of the cases is to bring positive changes in society. ...
Both theater plays and movies are forms of entertainment that allow an audience to enter different worlds. ...
Both theater plays and movies are forms of entertainment
Answer:
Theatre typically involves live performances, while cinema usually contains a moving picture that is prerecorded or premade and being projected.
Examples of theatre include:
BalletsPlaysMusicalsExamples of cinema include:
MoviesShort FilmsTo learn more about the difference between cinema and theatre, check out the link below:
https://brainly.com/question/26197760