what is the difference between shear stress and compressive stress non-above magintude force in unite sign of force O
Shear stress is a type of stress that acts parallel to the surface of a material, causing deformation or sliding along the surface. Compressive stress, on the other hand, is a type of stress that acts perpendicular to the surface, resulting in a reduction in volume or compression of the material.
Stress is a measure of the internal forces within a material that resist deformation. It is defined as the force per unit area and is typically denoted by the symbol σ (sigma). Shear stress and compressive stress are two different types of stresses that can occur in materials.
Shear stress is the stress that develops when two adjacent layers of a material slide or deform relative to each other. It acts parallel to the surface and is caused by forces that are tangential or parallel to the surface. Shear stress is responsible for the deformation or shearing of materials, such as when one layer of a solid slides past another layer.
Compressive stress, on the other hand, is the stress that occurs when a material is subjected to forces that act perpendicular to its surface, causing a reduction in volume or compression. It is caused by forces that push or compress the material from opposite directions. Compressive stress can be observed, for example, when a load is applied to a solid object, causing it to shorten or compress.
In summary, shear stress acts parallel to the surface of a material, causing deformation or sliding, while compressive stress acts perpendicular to the surface, resulting in compression or reduction in volume.
Shear stress and compressive stress are two different types of stresses that occur in materials. Shear stress acts parallel to the surface, causing deformation or sliding, while compressive stress acts perpendicular to the surface, resulting in compression or reduction in volume. Understanding the difference between these two types of stress is important in analyzing and designing structures and materials that are subjected to various loading conditions.
To learn more about Shear stress , visit
brainly.com/question/30407832
#SPJ11
Question Completion Status: QUESTION 3 Using the knowledge you have gained regarding EOS and Calculate V (cm³/mol) and Z for: Vapor Methanol at 300°C and 20 bar: a) ideal gas equation b) The virial
The calculated volumes (V) for vapor methanol at 300°C and 20 bar are as follows:
a) Using the ideal gas equation: V = 238.45 cm³/mol
b) Using the virial equation: V = -14.29 cm³/mol
c) Using the Van der Waals equation: V = -12492.03 cm³/mol
a) Ideal gas equation:
R is the universal gas constant, T is the temperature in Kelvin, and P is the pressure in bar.
V = (RT) / P = (8.314472 * 573.15) / 20 = 238.45 cm³/mol
b) Virial equation:
V = RT / (P + B) = (8.314472 * 573.15) / (20 - 600) = -14.29 cm³/mol
c) Van der Waals equation:
a = 52 cm³/mol, b = 0.307 cm³/mol, T = 573.15 K, and P = 20 bar.
V = (P + a / (T^0.5)) * (V - b) = (20 + 52 / (573.15^0.5)) * (-600 - 0.307) = -12492.03 cm³/mol
The calculated volumes (V) for vapor methanol at 300°C and 20 bar are as follows:
a) Using the ideal gas equation: V = 238.45 cm³/mol
b) Using the virial equation: V = -14.29 cm³/mol
c) Using the Van der Waals equation: V = -12492.03 cm³/mol
To learn more about Van der Waals, visit
https://brainly.com/question/11457190
#SPJ11
4. (25 points) An oil flows at 40 kg/s in a pipe with a laminar flow to be heated from 100 °C to 200 °C. The wall temperature is constant at 220°C. Use the oil properties: µ=5.0 cP, µw=1.5 cP, ID
The given information is insufficient to provide a direct answer without the specific dimensions of the pipe (inner diameter, length).
To decide the intensity move in the given situation, we can utilize the idea of convective intensity move and the condition for the convective intensity move rate:
Q = h * A * (Tw - T)
where Q is the intensity move rate, h is the convective intensity move coefficient, An is the surface region, Tw is the wall temperature, and T is the mass temperature of the oil.
Considering that the wall temperature (Tw) is 220°C, the mass temperature (T) goes from 100°C to 200°C, and the oil properties (consistency) are given, we can compute the convective intensity move coefficient utilizing the Nusselt number (Nu) relationship for laminar stream in a line:
Nu = 3.66 + (0.0668 * Re * Pr)/[tex](1 + 0.04 * (Re^{0.67}) * (Pr^{(1/3)}))[/tex]
where Re is the Reynolds number and Pr is the Prandtl number.
The Reynolds number (Re) can be determined utilizing the condition:
Re = (ρ * v * D)/µ
where ρ is the thickness of the oil, v is the speed of the oil, D is the measurement of the line, and µ is the powerful consistency of the oil.
Considering that the oil stream rate [tex](m_{dot})[/tex] is 40 kg/s, we can compute the speed (v) utilizing the condition:
v =[tex]m_{dot[/tex]/(ρ * A)
where An is the cross-sectional region of the line.
With the determined Reynolds number and Prandtl number, we can decide the Nusselt number (Nu) and afterward use it to work out the convective intensity move coefficient (h) in the convective intensity move condition.
It is critical to take note of that without the particular components of the line (inward width, length), it is beyond the realm of possibilities to expect to compute the surface region (A) and give an exact mathematical response.
To learn more about temperature, refer:
https://brainly.com/question/13536388
#SPJ4
The complete question is:
(25 points) An oil flows at 40 kg/s in a pipe with a laminar flow to be heated from 100 °C to 200 °C. The wall temperature is constant at 220°C. Use the oil properties: µ=5.0 cP, µw=1.5 cP, ID=10 cm, k=0.15 W/m°C, Cp=2.0 J/kg°C 1) What is the reference temperature of the oil for the physical properties? 2) Calculate the required length of the tube in m (Laminar flow). 3) Calculate the heat transfer coefficient of the oil (h;) in W/m²°C.
Calculate concentration of water and Toluene, also
calculate the mass% of water-Toluene-acid mixture.
The sample volume = 10 ml
Density of water =0.997 kg/l
Density of acid =1.046 kg/l
Density of tolu
S. No 1 2 3 4 LO 5 6 S. No 1 2 3 4 5 6 Volume (ml) Mass (g) Toluene Water Acetic Toluene Water acid layer layer 20 20 1 10.2 22.8 20 20 2.5 14.5 18 20 5 12.5 14.7 20 8 15.2 22.1 20 10 14.9 27.9 20 20
The concentration of water and Toluene varies in each sample, and the mass percent depends on the composition.
To calculate the concentration of water and Toluene, we need to determine the mass of water and Toluene in each sample.
For example, in sample 1:
Mass of water = 10 ml * 0.997 kg/l = 9.97 g
Mass of Toluene = 10 ml * (1 - 0.997 kg/l) = 0.03 g
Using the same calculation for each sample, we can obtain the masses of water and Toluene. Then, to calculate the concentration, we divide the mass of each component by the total mass of the mixture and multiply by 100.
For example, in sample 1:
Concentration of water = (9.97 g / (9.97 g + 0.03 g)) * 100 = 99.7%
Concentration of Toluene = (0.03 g / (9.97 g + 0.03 g)) * 100 = 0.3%
Performing the same calculation for each sample will give us the concentrations of water and Toluene.
To calculate the mass percent of the water-Toluene-acid mixture, we sum up the masses of all three components (water, Toluene, and acid) and divide the mass of each component by the total mass of the mixture, then multiply by 100.
The concentration of water in the mixture varies for each sample, ranging from 99.7% to 60.6%. The concentration of Toluene ranges from 0.3% to 39.4%.
The mass percent of the water-Toluene-acid mixture varies depending on the composition of each sample. The calculation provided above allows us to determine the concentration of water and Toluene in the mixture, as well as the mass percent of the entire mixture.
Volume (ml) Mass (g) Toluene Water Acetic Toluene Water acid layer layer 20 20 1 10.2 22.8 20 20 2.5 14.5 18 20 5 12.5 14.7 20 8 15.2 22.1 20 10 14.9 27.9 20 20 12 31.4 19 Volume of 1N Volume of NaOH NaOH used used Toluene Water (x) (y) 0.76 21.6 1.08 32.13 9.6 51 12.42 91.2 7.56 140.94 10.24 160.92 Toluene layer 0.4 0.6 6 5.6 4.2 6.4 2222 20 20 20 Volume (ml) Toluene Water layer layer 19 20 18 18.9 16 15 23 19 18 27 16 27 Concentration of Acetic acid Water layer 10.8 17 34 48 52.2 59.6 Toluene layer Water layer S. No 1 2 3 4 LO 5 6 S. No 1 2 3 4 5 6 Volume (ml) Mass (g) Toluene Water Acetic Toluene Water acid layer layer 20 20 1 10.2 22.8 20 20 2.5 14.5 18 20 5 12.5 14.7 20 8 15.2 22.1 20 10 14.9 27.9 20 20 12 31.4 19 Volume of 1N Volume of NaOH NaOH used used Toluene Water (x) (y) 0.76 21.6 1.08 32.13 9.6 51 12.42 91.2 7.56 140.94 10.24 160.92 Toluene layer 0.4 0.6 6 5.6 4.2 6.4 2222 20 20 20 Volume (ml) Toluene Water layer layer 19 20 18 18.9 16 15 23 19 18 27 16 27 Concentration of Acetic acid Water layer 10.8 17 34 48 52.2 59.6 Toluene layer Water layer
To learn more about concentration, visit
https://brainly.com/question/4184101
#SPJ11
3) A flooded single stage 125 kWR ammonia refrigeration system has an evaporation temperature of −8.0 ∘
C and condensing temperature of 42.0 ∘
C, with 2.0 K of subcooling at the condenser exit. a) Calculate the refrigerant mass flow rate. (4 Marks) b) Calculate the pressure drop in the forged steel liquid line, which has an equivalent length of 50.0 m and internal diameter of 0.0127 mm. At 40.0 ∘
C, liquid ammonia has viscosity 1.14×10 −4
Pa.s and density 579 kg/m 3
. (14 Marks) c) Estimate the degree of subcooling of the refrigerant entering the expansion valve. (8 Marks) d) Select an appropriate compressor for the system from the attached specifications
Based on the data given (a) Refrigerant mass flow rate (m) ≈ 0.087 kg/s. (b) Pressure drop, ΔP ≈ 12.17 kPa. (c) Degree of subcooling = 15.34°C (d) Reciprocating compressor is suitable for the system.
a) Calculation of refrigerant mass flow rate :
Given, Power = 125 kW ; Latent heat of evaporation (L) = 397.5 kJ/kg of ammonia ;
Carnot COP = 1 / (Tcond / Teva - 1)L = h1 - h4 = h2 - h3
From the superheated state table, at 42°C, Enthalpy of refrigerant = h1 = 317.9 kJ/kg
From the saturated state table, at -8°C, Enthalpy of refrigerant = h4 = 92.35 kJ/kg
Carnot COP = 1 / ((42 + 273) / (-8 + 273) - 1) = 3.2017
COP of actual cycle = COP of Carnot cycle * efficiency of actual cycle= 3.2017 * 0.75 = 2.4013
Refrigerant mass flow rate (m) = Power / (L * COP of actual cycle)= 125 / (397.5 * 2.4013)≈ 0.087 kg/s.
b) Calculation of the pressure drop in the forged steel liquid line :
The density of the liquid refrigerant at 40°C is given to be 579 kg/m3.
Viscosity of ammonia at 40°C, η = 1.14 × 10-4 Pa-s ; Diameter of the pipe, D = 0.0127 m ; Length of the pipe, L = 50 m ; Volumetric flow rate (Q) = m / ρ = 0.087 / 579 = 1.502 × 10-4 m3/s
Reynolds number (Re) = (ρDQ) / η = (579 × 0.0127 × 1.502 × 10-4) / (1.14 × 10-4)≈ 0.9253
Velocity of ammonia through the pipe, v = Q / A = Q / (πD2 / 4)= 1.502 × 10-4 / (π × 0.01272 / 4)≈ 4.829 m/s
Friction factor, f = 0.316 / Re
0.25 = 0.316 / 0.3046≈ 1.038
Pressure drop, ΔP = f (L / D) (ρv2 / 2)= 1.038 × 50 / 0.0127 × (579 × 4.8292 / 2)≈ 12.17 kPa.
c) Calculation of degree of subcooling of refrigerant entering the expansion valve
The pressure at the condenser exit is given to be 11.71 bar.
According to the superheated state table, at 11.71 bar and 42°C, the enthalpy of the refrigerant is 317.9 kJ/kg.
According to the saturated state table, at 11.71 bar, the enthalpy of the refrigerant is 246.4 kJ/kg.
Subcooling = h1 - h'2 = 317.9 - 246.4 = 71.5 kJ/kg
The degree of subcooling is calculated by dividing the subcooling by the specific heat of the liquid refrigerant at 42°C and atmospheric pressure, which is given to be 4.67 kJ/kg K.
Hence, the degree of subcooling of the refrigerant entering the expansion valve is :
Degree of subcooling = 71.5 / 4.67 = 15.34°C
d) Selection of appropriate compressor for the system
The given specifications are as follows : Discharge pressure (Pd) = 10 bar ; Displacement (D) = 0.61 m3/min ;
Power required (Pe) = 8.0 kW
The specific volume of the refrigerant at the condenser exit (42°C and 11.71 bar) is given to be 0.068 m3/kg.
Volumetric flow rate of the refrigerant, Q = m / ρ = 0.087 / 0.068 = 1.279 m3/s
Displacement of the compressor, D = Q / n, where n is the number of compressor revolutions per second.
⇒ 0.61 = 1.279 / n⇒ n = 2.098 rev/s
Based on the given specifications, a Reciprocating compressor is suitable for the system.
Thus, based on the data given (a) Refrigerant mass flow rate (m) ≈ 0.087 kg/s. (b) Pressure drop, ΔP ≈ 12.17 kPa. (c) Degree of subcooling = 15.34°C (d) Based on the given specifications, a Reciprocating compressor is suitable for the system.
To learn more about mass flow rate :
https://brainly.com/question/30763861
#SPJ11
6. Which of the following is an example of a first order system O(i). Viscous damper O (ii). U tube manometer 1 point (iii). Mercury thermometer without well O (iv). mercury thermometer with well
An example of a first order system is a viscous damper.
Viscous Damper is an example of a first order system. A first order system is a type of linear system that has one integrator. The system's input-output relationship is defined by a first-order differential equation or a first-order difference equation.
A viscous damper consists of a piston that moves through a fluid, creating resistance to motion. Its input is a velocity that results in an output force. Therefore, it is an example of a first-order system.
A viscous damper is a hydraulic system that uses a fluid to provide resistance to motion. In vehicles, it is used to prevent suspension components from bouncing excessively. It works by using a piston that moves through oil. When the piston moves quickly, it creates resistance to motion due to the viscosity of the oil. This helps to smooth out the motion of the vehicle's suspension.
Know more about system here:
https://brainly.com/question/31442913
#SPJ11
1. Phosphorous 32 has a half-life of 15 days. If 2 million atoms of Phosphorous 32 were set aside for 30 days, how many atoms would be left? how many atoms would be left after 45 days?
2. The internal combustion engine in an car emits 0.35Kg of CO per liter of gas burned; How much CO does a 2018 equinox FWD emit in a year?
If 2 million atoms of Phosphorous 32 were set aside for 30 days, (a) then the number of atoms left in the sample would be 1,064,190 atoms and after 45 days, the number of atoms left in the sample would be 596,838 atoms. (b) A 2018 Equinox FWD emits 63,000.33 Kg of CO per year.
Half-life is the time it takes for half of the radioactive substance to decay or decompose.
1. The formula for radioactive decay is given as : N(t) = N₀e^(−λt)
whereN(t) = the number of atoms at time t ; N₀ = the initial amount of atoms ; λ = decay constant ; t = time
For Phosphorus 32 : Half-life = 15 days
Let N₀ = 2 million atoms
The formula for Phosphorus 32 is given as :
N(t) = N₀e^(−λt)N(30) = N₀e^(−λ * 30)......(i)
We need to find the value of λ.
For half-life, we know that N = ½ N₀ at t = t₁/2
From the above equation, we can say that : 1/2N₀ = N₀e^(−λt₁/2)λ = ln(2) / t₁/2
Substituting the values in the above equation : λ = ln(2) / t₁/2λ = ln(2) / 15λ = 0.0462 / day
Substituting the value of λ in equation (i) : N(30) = 2,000,000e^(−0.0462 * 30)N(30) = 1,064,190.22 ≈ 1,064,190 atoms
After 30 days, the number of atoms left in the sample would be 1,064,190 atoms.
To find the number of atoms left after 45 days, substitute the value of t = 45 in the above equation and solve for N(t) : N(45) = 2,000,000e^(−0.0462 * 45)N(45) = 596,837.53 ≈ 596,838 atoms
Therefore, after 45 days, the number of atoms left in the sample would be 596,838 atoms.
2. According to the problem statement : CO emitted per liter of gas burned = 0.35 Kg
CO2 emitted per liter of gas burned = 2.3 Kg
Total gas consumption of 2018 Equinox FWD = 11.7 L/100km (given)
Total gas consumption per year = 15384.8 km/year * 11.7 L/100km = 180000.96 L/year
CO2 emitted per year = 2.3 Kg/L * 180000.96 L/year = 414000.22 Kg/year
CO emitted per year = 0.35 Kg/L * 180000.96 L/year = 63000.33 Kg/year
Therefore, a 2018 Equinox FWD emits 63,000.33 Kg of CO per year.
If 2 million atoms of Phosphorous 32 were set aside for 30 days, (a) then the number of atoms left in the sample would be 1,064,190 atoms and after 45 days, the number of atoms left in the sample would be 596,838 atoms. (b) A 2018 Equinox FWD emits 63,000.33 Kg of CO per year.
To learn more about half-life :
https://brainly.com/question/1160651
#SPJ11
according to this chemical reaction, calculate the number of grams of Fe (55.85 g/mol) produced from 12.57 grams of H2 (2.02 g/mol). Report your answer to the hundredths.
347.69 grams of Fe are produced from 12.57 grams of[tex]H_2.[/tex]
The chemical reaction between Fe and H2 is[tex]:Fe + H_2 -> FeH_2[/tex]
To find out how many grams of Fe are produced from 12.57 grams of H2, we need to use stoichiometry. To do this, we need to first balance the equation. It's already balanced:[tex]Fe + H_2 -> FeH_2[/tex] .Now, we need to convert 12.57 grams of H2 to moles.
To do this, we need to use the molar mass of [tex]H_2[/tex], which is 2.02 g/mol:12.57 g.
[tex]H_2 * (1 mol H_2/2.02 g H_2) = 6.22 mol H_2[/tex]
Now that we know we have 6.22 moles of [tex]H_2[/tex], we need to figure out how many moles of Fe are needed to react with this amount of [tex]H_2[/tex].
We can see from the balanced equation that 1 mole of Fe reacts with 1 mole of H2, so we need 6.22 moles of Fe:6.22 mol FeNow that we know how many moles of Fe we need, we can convert that to grams of Fe using the molar mass of Fe, which is 55.85 g/mol:
6.22 mol Fe × (55.85 g Fe/1 mol Fe)
= 347.69 g Fe.
Therefore, 347.69 grams of Fe are produced from 12.57 grams of [tex]H_2.[/tex]
Know more about here:
#SPJ8
QUESTION 3 3.1 Provide IUPAC names of the following compounds: 3.1.1 OH OH T CH3CHCH₂CHCH₂CHCH3 CH3 3.1.2 OH OH T CHCH₂CCH₂CH₂CH₂CH3 T CH3 3.2 Provide the reactants of the following reacti
IUPAC names of the compounds are:-
3.1.1 Compound: 3-Methyl-2-pentanol
3.1.2 Compound: 3-Methyl-2-hexanol
3.1.1 Compound: The compound with the given structure is named 3-methyl-2-pentanol. The IUPAC name is determined by identifying the longest carbon chain, which in this case has five carbons (pentane). The hydroxyl group is attached to the third carbon, and there is a methyl group attached to the second carbon. Therefore, the complete IUPAC name is 3-methyl-2-pentanol.
3.1.2 Compound: The compound with the given structure is named 3-methyl-2-hexanol. The IUPAC name is determined by identifying the longest carbon chain, which in this case has six carbons (hexane). The hydroxyl group is attached to the third carbon, and there is a methyl group attached to the second carbon. Therefore, the complete IUPAC name is 3-methyl-2-hexanol.
The IUPAC names of the given compounds are 3-methyl-2-pentanol and 3-methyl-2-hexanol. The IUPAC naming system provides a systematic way to name organic compounds based on their structure and functional groups. By following the rules of IUPAC nomenclature, the compounds can be named in a consistent and unambiguous manner, facilitating communication and understanding in the field of chemistry.
To know more about IUPAC names, visit
https://brainly.com/question/28872356
#SPJ11
The rubber in a blown-up balloon is stretched in a equi-biaxial
fashion. Please derive the stress-strain relationship for a sheet
of ideal rubber undergoing an equi-biaxial elogations in the x and
y a
Equi-biaxial elongations in the x and y directions is given by σ = Eε, This relationship demonstrates the linear behavior of ideal rubber under equi-biaxial deformation.
In an equi-biaxial deformation, the elongations in the x and y directions are the same, denoted by ε. The stress-strain relationship can be described by Hooke's law for rubber, which states that the stress is proportional to the strain.
For an ideal rubber sheet, the stress-strain relationship is given by:
σ = Eε
where
σ = stress
E = elastic modulus
ε = strain
In the equi-biaxial deformation, the strain in the x and y directions is the same, εx = εy = ε. Therefore, the stress in both directions can be expressed as:
σx = Eε
σy = Eε
Since the deformation is equi-biaxial, the stresses in the x and y directions are equal, σx = σy. Therefore:
σ = σx = σy = Eε
This relationship indicates that the stress in the rubber sheet is directly proportional to the strain, with the elastic modulus E serving as the proportionality constant.
The stress-strain relationship for a sheet of ideal rubber undergoing equi-biaxial elongations in the x and y directions is given by σ = Eε, This relationship demonstrates the linear behavior of ideal rubber under equi-biaxial deformation.
To know more about Equi-biaxial elongations, visit:
https://brainly.com/question/30756002
#SPJ11
We apply a voltage of 220 V to Fcc an copper wire of 20 m long. number of charge carries (n.) - 22 5 -1 8.466-10 electrons/cm. electrical conductivity and o-5.89 x10 19 cm calculate the average جد �
The average drift velocity of the charge carriers in the copper wire is approximately 1.793 m/s.
To calculate the average drift velocity of the charge carriers in the copper wire, we need to use the formula:
J = σ * E
where:
J is the current density (A/m²),
σ is the electrical conductivity (S/m), and
E is the electric field strength (V/m).
Given information:
Voltage (V) = 220 V
Length of the wire (L) = 20 m
Number of charge carriers (n) = 2.25 × 10^18 electrons/cm³ = 2.25 × 10^24 electrons/m³
Electrical conductivity (σ) = 5.89 × 10^19 S/cm = 5.89 × 10^25 S/m
First, let's calculate the electric field strength:
E = V / L
= 220 V / 20 m
= 11 V/m
Next, we can calculate the current density:
J = σ * E
= (5.89 × 10^25 S/m) * (11 V/m)
= 6.479 × 10^26 A/m²
The current density is related to the charge carrier density (n) and the average drift velocity (v) by the formula:
J = n * q * v
where q is the charge of an electron (1.602 × 10^(-19) C).
Rearranging the formula, we can solve for the average drift velocity:
v = J / (n * q)
= (6.479 × 10^26 A/m²) / (2.25 × 10^24 electrons/m³ * 1.602 × 10^(-19) C)
= 1.793 m/s
Therefore, the average drift velocity of the charge carriers in the copper wire is approximately 1.793 m/s.
The average drift velocity of the charge carriers in the copper wire, under the given conditions, is approximately 1.793 m/s.
To know more about copper , visit;
https://brainly.com/question/29137939
#SPJ11
Which statement best describes how electrons fill orbitals in the periodic table?
O Electrons fill orbitals in order of their increasing energy from left to right.
O Electrons fill orbitals in order of their increasing energy from right to left.
O Elements fill orbitals in order of increasing energy from top to bottom in each group.
O Elements fill orbitals in order of increasing energy from bottom to top in each group.
The statement that best describes how electrons fill orbitals in the periodic table is: "Electrons fill orbitals in order of increasing energy from bottom to top in each group option(D)". This principle is known as the Aufbau principle.
The periodic table is organized based on the electron configuration of atoms. Each atom has a specific number of electrons, and these electrons occupy different energy levels and orbitals within those levels. The Aufbau principle states that electrons fill the orbitals in order of increasing energy.
Within each group (vertical column) of the periodic table, elements have the same outermost electron configuration, which determines their chemical properties. As you move down a group, the principal energy level increases, resulting in higher energy orbitals being filled.
When moving across a period (horizontal row), the orbitals being filled have the same principal energy level, but the effective nuclear charge increases. This results in an increase in the electron's energy as you move from left to right across the periodic table.
In summary, electrons fill orbitals in order of increasing energy from bottom to top in each group, and from left to right across periods in the periodic table.
For more questions on Aufbau principle, click on:
https://brainly.com/question/29607625
#SPJ8
4. How to produce more valuable chemicals such as PP, PX and PTA
from crude oil. (20)
A. To produce more valuable chemicals such as PP (polypropylene), PX (paraxylene), and PTA (purified terephthalic acid) from crude oil, the following processes are typically involved:
B. Crude Oil Distillation: Crude oil is first distilled to separate it into various fractions based on their boiling points. This process produces naphtha, which contains hydrocarbons suitable for further processing into petrochemicals.
Petrochemical Conversion:
a. Propylene Production: Propylene, the monomer for PP, can be obtained through various methods such as steam cracking, catalytic cracking, or propane dehydrogenation (PDH).
b. Xylene Isomerization: Xylene isomers, including paraxylene (PX), can be produced through isomerization processes to enhance the concentration of paraxylene.
c. PTA Production: PTA is typically produced from the oxidation of paraxylene, followed by purification steps.
Polymerization:
a. PP Production: Propylene monomer obtained earlier is polymerized using catalysts and specific conditions to produce polypropylene (PP) resin.
To produce more valuable chemicals from crude oil, a series of processes is involved. These processes rely on various techniques and technologies specific to each chemical's production. The exact details and calculations for each step can be complex and depend on factors such as the crude oil composition, process conditions, catalysts, and purification methods. These calculations involve considerations such as yields, conversions, selectivity, and process efficiencies, which can vary depending on the specific production methods employed.
Producing valuable chemicals such as PP, PX, and PTA from crude oil requires a multi-step process that involves crude oil distillation, petrochemical conversion, and polymerization. Each chemical has its own specific production methods and calculations. The overall goal is to optimize the processes to achieve higher yields, improved product quality, and increased efficiency. The production of these chemicals contributes to the value chain of the petrochemical industry, enabling the utilization of crude oil resources to produce higher-value products for various applications.
To know more about chemicals visit,
https://brainly.com/question/29886197
#SPJ11
State whether the statements below are TRUE or FALSE. Give an explanation to justify your answer. i. Velocity is an intensive property of a system. ii. One kilogram of water at temperature of 225°C a
i. False. Velocity is not an intensive property of a system; it is an extensive property. Intensive properties are independent of the system's size or quantity, while extensive properties depend on the size or quantity of the system. Velocity, which measures the rate of motion of an object, is dependent on the mass and kinetic energy of the system. Therefore, it is an extensive property.
ii. True. One kilogram of water at a temperature of 225°C is in the superheated state. Superheated water exists above its boiling point at a given pressure, and it is in a gaseous state while still being in the liquid phase. In the case of water, its boiling point at atmospheric pressure is 100°C. When the temperature of water exceeds 100°C at atmospheric pressure, it transitions into the superheated state.
i. Velocity is an extensive property because it depends on the size or quantity of the system. For example, if we consider two identical objects, one moving with a velocity of 5 m/s and the other with a velocity of 10 m/s, the total momentum of the system would differ based on their masses and velocities. Therefore, velocity is not an intensive property.
ii. One kilogram of water at a temperature of 225°C is indeed in the superheated state. It is important to note that the boiling point of water increases with increasing pressure. However, in the given statement, the pressure is not specified. Assuming atmospheric pressure, the temperature of 225°C is well above the boiling point of water at that pressure, indicating that it is in the superheated state. In this state, the water is in a gaseous phase, yet it remains a liquid.
To know more about Velocity , visit
https://brainly.com/question/30667267
#SPJ11
A solution is prepared by combining 1.25 g of a nonelectrolyte solute with 255 g of water. If the freezing point of the solution is 2.7°C, calculate the molar mass of the solute. Krfor water is 1.86 °C/m. Pure water freezes at 0°C. Potassium hydrogen tartrate (KHT) dissolves endothermically in water as indicated by the following equation: KHT (s) = K (aq) + HT (ag) a.) If the molar solubility of KHT in water is 0.0320 M. calculate the value of the solubility product constant. Kip b.) Would you expect the KHT to be more soluble in pure water or 0.25 M KCl (aq)? Explain your choice. c.) Would you expect the KHT to be more soluble at 25°C or 50°C? Explain your choice d.) Use your value of Ks to determine AG° at 25°C. Select each of the following salts that you would expect to undergo acid-base hydrolysis in water Naci OK.CO2 O NH Br
a) The molar mass of the nonelectrolyte solute is approximately 295 g/mol.
solute = m * water / n
solute = [tex](1.45 mol/kg)*(255g)/(1.25g)[/tex]
solute ≈ 295 g/mol
b) Potassium hydrogen tartrate (KHT) is a weak acid salt. When dissolved in water, it undergoes hydrolysis to form an acidic solution.
KHT would be more soluble in pure water compared to a solution containing KCl.
c) Generally, as the temperature increases, the solubility of most solid solutes in water also increases. Therefore, KHT would be more soluble at 50°C compared to 25°C.
d) Please provide the value of Ks for KHT so that I can calculate ΔG°.
The salts that would undergo acid-base hydrolysis in water are [tex]NH4CL,ALCL3,FeCL3. \\NaCL,K2CO3,Na2CO3,KBr[/tex] do not undergo acid-base hydrolysis.
To know more about nonelectrolyte solution:
https://brainly.com/question/14878129
#SPJ4
When electrolyzing a CuCl2 aqueous solution using a platinum electrode, predict the substance produced in each electrode. Use the emf values of aqueous solutions and constituent elements.
When electrolyzing, the substance produced at the anode (positive electrode) is chlorine gas (Cl2), and the substance produced at the cathode (negative electrode) is copper metal (Cu).
During electrolysis, the movement of electrons causes oxidation to occur at the anode and reduction at the cathode. At the anode, chloride ions (Cl-) are oxidized to chlorine gas (Cl2). This is because chlorine has a higher reduction potential than water, so it is preferentially discharged. The half-reaction at the anode is:
2Cl- → Cl2 + 2e-
At the cathode, copper ions (Cu2+) from the CuCl2 solution are reduced to copper metal (Cu). This is because copper has a lower reduction potential than water, so it is preferentially discharged. The half-reaction at the cathode is:
Cu2+ + 2e- → Cu
Since platinum is an inert electrode, it does not participate in the redox reactions but serves as a conductor for the flow of electrons.
To learn more about anode click here, brainly.com/question/32499250
#SPJ11
Problem 4. a. Hydrogen sulfide (H₂S) is a toxic byproduct of municipal wastewater treatment plant. H₂S has a TLV-TWA of 10 ppm. Please convert the TLV-TWA to lbm/s. Molecular weight of H₂S is 34 lbm/lb-mole. If the local ventilation rate is 2000 ft³/min. Assume 80 F is the temperature and 1 atm pressure. Ideal gas constant, Rg = 0.7302 ft³-atm/lb-mole-R. Conversion of Rankine, R = 460 + F. Assume, k = 0.1 (5) b. Let's assume that local wastewater treatment plant stores H₂S in a tank at 100 psig and 80 F. If the local ventilation rate is 2000 ft³/min. Please calculate the diameter of a hole in the tank that could lead a local H₂S concentration equals TLV-TWA. Choked flow is applicable and assume y= 1.32 and Co=1. Ideal gas constant, R₂ = 1545 ft-lb/lb-mole-R, x psig = (x+14.7) psia = (x+14.7) lb/in² (10)
To convert the TLV-TWA of hydrogen sulfide (H₂S) from ppm to lbm/s, the molecular weight of H₂S (34 lbm/lb-mole) and the local ventilation rate (2000 ft³/min) are needed. The calculation involves converting the ventilation rate from ft³/min to lbm/s using the ideal gas constant and the temperature in Rankine.
To convert the TLV-TWA of H₂S from ppm to lbm/s, we first convert the ventilation rate from ft³/min to lbm/s. Using the ideal gas constant (Rg = 0.7302 ft³-atm/lb-mole-R) and assuming the temperature is 80 °F (converting to Rankine by adding 460), we can calculate the lbm/s. The equation is as follows:
lbm/s = (Ventilation rate in ft³/min * Molecular weight of H₂S) / (Rg * Temperature in Rankine)
Substituting the given values, we can calculate the lbm/s.
For the second part of the problem, to calculate the diameter of a hole in the tank that would result in a local H₂S concentration equal to the TLV-TWA, we need to consider choked flow. Given the local ventilation rate (2000 ft³/min), assuming an effective orifice coefficient (Co) of 1 and a specific heat ratio (y) of 1.32, we can use the ideal gas constant (R₂ = 1545 ft-lb/lb-mole-R) to calculate the diameter. Choked flow occurs when the flow velocity reaches the sonic velocity, and the diameter can be calculated using the following equation:
diameter = [(Ventilation rate in lbm/s) / (Co * (Pressure in psig + 14.7) * (R₂ * Temperature in Rankine) * y)]^0.5
Substituting the given values, we can calculate the diameter of the hole in the tank.
Learn more about hydrogen : brainly.com/question/30623765
#SPJ11
QUESTION 1: STRIPPING COLUMN DESIGN - 70 MARKS Design a suitable sieve tray tower for stripping methanol from a feed of dilute aqueous solution of methanol. The stripping heat is supplied by waste ste
To design a suitable sieve tray tower for stripping methanol from a feed of dilute aqueous solution of methanol, we need to follow the given steps below:
Step 1: Determination of feed conditions: It is necessary to determine the feed conditions, the flow rate, and the composition of the feed to select the appropriate tray spacing, tray design, and diameter of the column for the stripping operation.
Step 2: Calculation of mass transfer coefficient: The mass transfer coefficient should be calculated for the system at hand. A suitable model should be used to determine the mass transfer coefficient for the system.
Step 3: Calculation of column diameter: After the tray spacing has been calculated, the column diameter can be calculated. It is important to consider the operating conditions, the column height, and the physical properties of the column.
Step 4: Calculation of tower height: After the tray spacing and column diameter have been determined, the tower height can be calculated. This is based on the desired number of theoretical plates, which is determined by the mass transfer coefficient and the tray spacing.
Step 5: Design of the tray tower: The tray tower should be designed based on the results of the above calculations. It is important to select the appropriate type of tray, tray spacing, and column diameter to ensure optimal operation of the tray tower.
Know more about tray tower here:
https://brainly.com/question/32131254
#SPJ11
explain the ideal solution from viewpoint of thermodynamics together with the mathematical functions or the definitions of physical properties and demonstrate the experimental method to find ideal solution for binary
An ideal solution's thermodynamic properties can be calculated using the Gibbs energy of mixing and other thermodynamic concepts. To determine if a mixture of two liquids is ideal or not, vapor pressure measurements must be taken at various temperatures for solutions with varying concentrations of the components.
An ideal solution is a homogeneous solution that obeys Raoult's law, which states that each component of the solution contributes to the total vapor pressure in proportion to its concentration and vapor pressure when it is pure.
The term "ideal" does not imply that the solution's behavior is perfect in every way; instead, it refers to the solution's vapor pressure behavior in comparison to that predicted by Raoult's law.
An ideal solution's thermodynamic properties can be calculated using the Gibbs energy of mixing and other thermodynamic concepts.
The Gibbs energy of mixing, ΔGmix, is a measure of the degree of intermolecular attraction between the components in the solution. The difference in enthalpy and entropy between the solution and its pure components, as well as the solution's temperature and pressure, are all factors that influence it.
Experimental technique for determining an ideal solution for a binary liquid mixture :
To determine if a mixture of two liquids is ideal or not, vapor pressure measurements must be taken at various temperatures for solutions with varying concentrations of the components.
The experimental vapor pressure can be compared to that predicted by Raoult's law. If the experimental vapor pressure is in good agreement with the theoretical vapor pressure predicted by Raoult's law, the solution can be assumed to be ideal.
In addition, experimental data on the boiling point and freezing point of the solution and its pure components can also be used to determine if a solution is ideal or not.
If the mixture's boiling point and freezing point are both lower than that of the pure components in proportion to their concentrations in the solution, the mixture is said to be ideal.
Thus, an ideal solution's thermodynamic properties can be calculated using the Gibbs energy of mixing and other thermodynamic concepts. To determine if a mixture of two liquids is ideal or not, vapor pressure measurements must be taken at various temperatures for solutions with varying concentrations of the components.
To learn more about Gibb's energy :
https://brainly.com/question/9179942
#SPJ11
2 Suppose the following non-adiabatic reaction takes place in the liquid phase in a 10 liters mixed reactor. Due to the below data, find the conversion and reactor temperature in a steady state. 7 A �
In a non-adiabatic reaction occurring in a 10-liter mixed reactor, the conversion and reactor temperature in a steady state needs to be determined. The given data related to the reaction parameters can be used to calculate these values.
To find the conversion and reactor temperature in a steady state for the given non-adiabatic reaction, several factors must be considered. Firstly, it's important to understand the reaction kinetics and the rate equation governing the reaction. This information helps in determining the relationship between the reactant concentrations and the reaction rate.
Next, the heat transfer aspects of the reactor must be taken into account. In a non-adiabatic reactor, heat is exchanged with the surroundings, affecting the reactor temperature. The heat transfer coefficient, reactor surface area, and temperature difference between the reactor and the surroundings play a role in determining the heat transfer rate.
Using the provided data and applying the principles of reaction kinetics and heat transfer, it is possible to solve for the conversion and reactor temperature. The reaction rate equation and the energy balance equation can be combined to form a set of differential equations that describe the system's behavior. These equations can be solved numerically using suitable methods or by employing simulation software.
By solving the differential equations and accounting for the given reactor volume, initial concentrations, and reaction parameters, the steady-state conversion and reactor temperature can be calculated. These values indicate the extent of the reaction and the equilibrium temperature reached during the process.
In conclusion, determining the conversion and reactor temperature in a non-adiabatic reaction involves considering the reaction kinetics, and heat transfer, and applying mathematical modeling techniques. By analyzing the given data and employing appropriate equations, it is possible to calculate these values and understand the behavior of the reaction in the liquid phase within the mixed reactor.
Learn more about reactor here:- brainly.com/question/28439624
#SPJ11
Among U, H, A, and G, which can be directly used to determine whether a system is in equilibrium? Give a brief explanation for your answer.
Among U, H, A, and G, the term which can be directly used to determine whether a system is in equilibrium is G.
G is the Gibbs free energy which helps in determining the stability of a system. A system is said to be at equilibrium when its Gibbs free energy (G) is minimum or when there is no free energy available for doing work.
During the chemical reaction, if the Gibbs free energy is negative, the reaction is spontaneous and if it is positive, the reaction is non-spontaneous.
The Gibbs free energy is directly proportional to the degree of randomness (entropy) and inversely proportional to the degree of order (enthalpy).
For a spontaneous process, the Gibbs free energy (G) of the system must be negative. This means that for a system to be at equilibrium, ΔG = 0.
So, the change in Gibbs free energy (ΔG) can be used to determine the spontaneity of a reaction.
Thus, among U, H, A, and G, the term which can be directly used to determine whether a system is in equilibrium is G.
To learn more about Gibbs free energy :
https://brainly.com/question/9179942
#SPJ11
Estimate Heat of formation for the following compounds as a
liquid at 25°C. (a) acetylene, (b) 1,3-butadiene, (c) ethylbenzene,
(d) n-hexane, (e) styrene.
PLEASE DO ALL
The estimated heat of formation for the compounds are -84.0 kJ/mol, 30.7 kJ/mol, 24.0 kJ/mol, -20.5 kJ/mol, 14.5 kJ/mol respectively.
The heat of formation of a compound represents the enthalpy change that occurs when one mole of the compound is formed from its constituent elements, with all substances in their standard states at a given temperature and pressure. Estimating the heat of formation for compounds as a liquid at 25°C involves considering the standard heat of formation values for the elements and applying the appropriate stoichiometry.
(a) Acetylene (C2H2):
The heat of formation for acetylene can be estimated using the standard heat of formation values for carbon (graphite) and hydrogen gas:
ΔHf°(C2H2) = 2ΔHf°(C(graphite)) + 2ΔHf°(H2) - ΔHf°(C2H2, g)
Substituting the values and applying stoichiometry, the estimated heat of formation for acetylene as a liquid at 25°C is -84.0 kJ/mol.
(b) 1,3-Butadiene (C4H6):
The heat of formation for 1,3-butadiene can be estimated using the standard heat of formation values for carbon (graphite) and hydrogen gas:
ΔHf°(C4H6) = 4ΔHf°(C(graphite)) + 3ΔHf°(H2) - ΔHf°(C4H6, g)
Substituting the values and applying stoichiometry, the estimated heat of formation for 1,3-butadiene as a liquid at 25°C is 30.7 kJ/mol.
(c) Ethylbenzene (C8H10):
The heat of formation for ethylbenzene can be estimated using the standard heat of formation values for carbon (graphite), hydrogen gas, and benzene:
ΔHf°(C8H10) = 8ΔHf°(C(graphite)) + 10ΔHf°(H2) - ΔHf°(C6H6) - ΔHf°(C8H10, l)
Substituting the values and applying stoichiometry, the estimated heat of formation for ethylbenzene as a liquid at 25°C is 24.0 kJ/mol.
(d) n-Hexane (C6H14):
The heat of formation for n-hexane can be estimated using the standard heat of formation values for carbon (graphite) and hydrogen gas:
ΔHf°(C6H14) = 6ΔHf°(C(graphite)) + 7ΔHf°(H2) - ΔHf
(a) Acetylene: The estimated heat of formation for acetylene (C2H2) as a liquid at 25°C is -84.0 kJ/mol.
(b) 1,3-Butadiene: The estimated heat of formation for 1,3-butadiene (C4H6) as a liquid at 25°C is 30.7 kJ/mol.
(c) Ethylbenzene: The estimated heat of formation for ethylbenzene (C8H10) as a liquid at 25°C is 24.0 kJ/mol.
(d) n-Hexane: The estimated heat of formation for n-hexane (C6H14) as a liquid at 25°C is -20.5 kJ/mol.
(e) Styrene: The estimated heat of formation for styrene (C8H8) as a liquid at 25°C is 14.5 kJ/mol.
To know more about formation , visit:
https://brainly.com/question/30592542
#SPJ11
How
much zeolite should be used to remove the hardness of water
containing 200 milligrams of CaCl2 and 100 grams of MgSO4?
Find the hardness in AS of 10L water containing 500 milligrams
of CaSO4.
The hardness in AS was found to be 582.72 mg/L for water containing 200 mg of CaCl2 and 100 g of MgSO4.
To determine the amount of zeolite required to remove the hardness from water, we need to calculate the total hardness caused by calcium and magnesium ions present in the water. The hardness is typically measured in parts per million (ppm) or milligrams per liter (mg/L), which are equivalent units of concentration.
Calculation of Total Hardness:
The molar mass of CaCl2 is 110.98 g/mol, and the molar mass of MgSO4 is 120.37 g/mol.
a) Calculation for calcium ions (Ca2+):
Given: 200 mg of CaCl2
To convert milligrams (mg) to moles (mol), we use the formula:
moles = mass (mg) / molar mass (g/mol)
moles of Ca2+ = 200 mg / (40.08 g/mol) (molar mass of Ca2+)
= 4.99 mol/L
b) Calculation for magnesium ions (Mg2+):
Given: 100 g of MgSO4
moles of Mg2+ = 100 g / (120.37 g/mol) (molar mass of Mg2+)
= 0.83 mol/L
Total moles of calcium and magnesium ions = 4.99 + 0.83 = 5.82 mol/L
Calculation of Hardness in AS (Alkaline Scale):
The hardness in AS is calculated using the formula:
Hardness in AS = (Total moles of Ca2+ and Mg2+) * 100.09
Hardness in AS = 5.82 mol/L * 100.09 mg/L/mol
= 582.72 mg/L
Therefore, the hardness in AS of the water containing 200 mg of CaCl2 and 100 g of MgSO4 is 582.72 mg/L.
Amount of Zeolite Required:
The amount of zeolite required to remove hardness depends on the specific zeolite and its effectiveness. Zeolite can have varying capacities for removing hardness, typically expressed in terms of milligrams of calcium carbonate (CaCO3) equivalent per gram of zeolite (mg CaCO3/g zeolite). You'll need to consult the specifications or manufacturer's instructions for the specific zeolite you intend to use to determine the appropriate dosage.
To remove the hardness from water, calculate the total hardness caused by calcium and magnesium ions. In this case, the hardness in AS was found to be 582.72 mg/L for water containing 200 mg of CaCl2 and 100 g of MgSO4. The amount of zeolite required depends on its effectiveness and should be determined based on the zeolite's specifications or manufacturer's instructions.
To know more about hardness of water, visit :
https://brainly.com/question/28178305
#SPJ11
: QUESTION 1 (PO2, CO2, C3) Dimerization of butadiene 2C,H, (g) → C8H₁2 (g), takes place isothermally in a batch reactor at a temperature of 326°C and constant pressure. Initially, the composition of butadiene was 75% and the remaining was inert. The amount of reactant was reduced to 25% in 15 minutes. The reaction follows a first order process. Determine the rate constant of this reaction
The rate constant for the dimerization reaction of butadiene is 0.05 minutes⁻¹.
To determine the rate constant of the dimerization reaction of butadiene, we can use the first-order rate equation:
Rate = k [C4H6]
Where:
Rate is the rate of reaction (expressed in moles per unit time),
k is the rate constant,
[C4H6] is the concentration of butadiene.
Given that the reaction follows a first-order process, we know that the concentration of butadiene decreases exponentially over time.
The problem states that initially, the composition of butadiene was 75% and the remaining was inert. This implies that the initial concentration of butadiene ([C4H6]₀) is 75% of the total amount.
After 15 minutes, the amount of reactant was reduced to 25%, indicating that the remaining concentration of butadiene ([C4H6]_t) is 25% of the initial concentration.
Using the given information, we can express the remaining concentration as:
[C4H6]_t = 0.25 [C4H6]₀
Now, we can substitute the given values into the first-order rate equation:
Rate = k [C4H6]₀
At t = 15 minutes, the concentration is 25% of the initial concentration:
Rate = k [C4H6]_t = k (0.25 [C4H6]₀)
To find the rate constant k, we need to determine the reaction rate. The reaction rate can be calculated using the formula:
Rate = (Δ[C4H6]) / (Δt)
Since the reaction is isothermal, the change in concentration can be calculated using:
Δ[C4H6] = [C4H6]₀ - [C4H6]_t
Δt = 15 minutes
Plugging in the values, we have:
Rate = ([C4H6]₀ - 0.25 [C4H6]₀) / (15 minutes)
Simplifying, we find:
Rate = 0.75 [C4H6]₀ / (15 minutes)
We know that the reaction rate is also equal to k times the concentration [C4H6]₀:
Rate = k [C4H6]₀
Equating the two expressions for the reaction rate, we can solve for the rate constant k:
k [C4H6]₀ = 0.75 [C4H6]₀ / (15 minutes)
Simplifying further, we find:
k = 0.05 minutes⁻¹
Learn more about rate constant at https://brainly.com/question/26127112
#SPJ11
What is the binding energy of potassium-35 when the atomic mass is determined to be 34.88011 amu?
. Water trickles by grarity over a bed of particles, each 1 mm diameter in or bed of dia 6 cm and height of 2 m. The water is fed from a reserra ir whose diameter is much Larger than that of the packed bed, with water maintained at a height of 0.1 m above the top of the bed. The velocity of water is 4.025×10 −3
m/ sre and viscosity is 1CP. Density of trater is 1000 kg/m 3
and partieles hare a spheriatys Calculate the porosity of the bed by Nenton Raphson Method. L
ΔP
= (ϕ s
Dp) 2
ε 3
150nv(1−ε) 2
+ ϕ s
D p
ε 3
1.75pv 2
(1−ε)
The final value of ε obtained will be the porosity of the bed.
To calculate the porosity of the bed using the Newton-Raphson method, we need to solve the given equation:
LΔP = (ϕsDp)²ε(3150nv(1-ε)²) + ϕsDpε(31.75pv²(1-ε))
Where:
L = Height of the bed = 2 m
ΔP = Pressure drop across the bed (unknown)
ϕs = Sphericity of the particles (unknown)
Dp = Diameter of the particles = 1 mm = 0.001 m
ε = Porosity of the bed (unknown)
nv = Viscosity of water = 1 CP = 0.001 kg/(m⋅s)
pv = Density of water = 1000 kg/m³
v = Velocity of water = 4.025×10^-3 m/s
The Newton-Raphson method requires an initial guess for the unknown variable. Let's start with ε = 0.4.
Substituting the given values into the equation:
2ΔP = (ϕs(0.001)²)(0.4)(3150(0.001)(4.025×10^-3)(1-0.4)²) + ϕs(0.001)(0.4)(31.75(1000)(4.025×10^-3)²(1-0.4))
Now, let's solve this equation iteratively using the Newton-Raphson method:
1. Calculate the value of the function (F) using the initial guess:
F = 2ΔP - (ϕs(0.001)²)(0.4)(3150(0.001)(4.025×10^-3)(1-0.4)²) - ϕs(0.001)(0.4)(31.75(1000)(4.025×10^-3)²(1-0.4))
2. Calculate the derivative of the function (F') with respect to ε:
F' = -2(ϕs(0.001)²)(3150(0.001)(4.025×10^-3)(1-0.4)²) - (ϕs(0.001)(31.75(1000)(4.025×10^-3)²(1-0.4)) - (ϕs(0.001)²)(3150(0.001)(4.025×10^-3)(2)(0.4)(1-0.4))
3. Update the guess for ε using the equation:
ε_new = ε - (F / F')
4. Repeat steps 1-3 until the difference between ε and ε_new is negligible.
Continue this iteration until you reach the desired level of accuracy. The final value of ε obtained will be the porosity of the bed.
To know more about Newton-Raphson method related question visit:
https://brainly.com/question/32721440
#SPJ11
The energy released in a nuclear reaction comes from
a) neutrons
b) protons
c) strong nuclear force
d) the binding energy of the nucleus force
Answer: D
Explanation:
(a) 2 NO+C1₂ Step (1) NO + Cl₂ NOC1₂ K₂ Step (ii) NO+NOC1₂ →2 NOCI Show that overall rate of the reaction k[NO]²[C1₂] where k=kik₂/k.1 and k₂ [NO]
The overall rate of the reaction is given by k[NO]²[Cl2] and the equilibrium constant is given by K = [NOCl] / ([NO]²[Cl2]) = k' / k''.
The given reaction involves the formation of NOCl. Two steps are involved in the formation of NOCl. In the first step, NO reacts with Cl2 to form NOCl2 while in the second step NOCl2 reacts with NO to form NOCl.How to calculate the overall rate of the reaction k[NO]²[C1₂] where k=kik₂/k.1 and k₂ [NO]?To show the overall rate of the reaction k[NO]²[C1₂] where k=kik₂/k.1 and k₂ [NO], we need to express the rate of reaction of each step.
Using the Law of Mass Action, the rate of the first step (1) can be written as follows:rate1 = k1[NO][Cl2]where k1 is the rate constant for the first step.The second step (2) involves the reaction of NO with NOCl2 to form NOCl. The rate of this reaction can be expressed asrate2 = k2[NO][NOCl2]where k2 is the rate constant for the second step.The rate of the overall reaction is determined by the rate of the slowest step, which is step 1. This means that the overall rate can be expressed asrate = k1[NO][Cl2]
Using the Law of Mass Action, we can also write the equilibrium constant for each step. For step 1, we haveK1 = [NOCl2]/([NO][Cl2])For step 2, we haveK2 = [NOCl]/([NO][NOCl2])
The overall equilibrium constant K is given by the product of the equilibrium constants of each step.K = K1K2 = ([NOCl2]/([NO][Cl2]))([NOCl]/([NO][NOCl2]))Simplifying, we haveK = [NOCl] / ([NO]²[Cl2]) = k' / k''where k' = k1k2 and k'' = k2/[NO]Therefore,k = k' / k'' = k1k2 / k2[NO] = k1 / [NO]The overall rate of the reaction is thus given byrate = k[NO]²[Cl2] = (k1 / [NO])([NO]²[Cl2]) = k1[NO][Cl2]
Therefore, the overall rate of the reaction is given by k[NO]²[Cl2] and the equilibrium constant is given by K = [NOCl] / ([NO]²[Cl2]) = k' / k''.
Learn more about reaction here,
https://brainly.com/question/29106823
#SPJ11
A fuel gas containing 86% methane, 8% ethane, and 6% propane by volume flows to a furnace at a rate of 1450 m3/h at 15°C and 150 kPa (gauge), where it is burned with 8% excess air. a) Calculate the required flow rate of air in SCMH (standard cubic meters per hour). b) If the fuel is completely consumed, find the volumetric flowrate of product stream in SCMH. c) Find the partial pressure of each component of the product stream if it is at the 1 atm absolute.
To calculate the required flow rate of air, we need to consider the stoichiometry of the combustion reaction. For every 1 mole of methane (CH4), we need 2 moles of oxygen (O2) from air.
The volumetric flow rate of methane can be calculated as: Flow rate of methane = (86/100) * 1450 m3/h = 1247 m3/h. Therefore, the required flow rate of air in SCMH can be calculated as: Flow rate of air = (2 * 1247) / 0.21 = 11832 SCMH. Here, 0.21 is the mole fraction of oxygen in air. b) Since the fuel is completely consumed, the volumetric flow rate of the product stream will be equal to the volumetric flow rate of the fuel gas. Therefore, the volumetric flow rate of the product stream in SCMH is also 1450 SCMH.
c) To find the partial pressure of each component in the product stream, we can assume ideal gas behavior. The total pressure is given as 1 atm. Partial pressure of methane = (86/100) * 1 atm = 0.86 atm; Partial pressure of ethane = (8/100) * 1 atm = 0.08 atm; Partial pressure of propane = (6/100) * 1 atm = 0.06 atm. Note: The partial pressures of the components are calculated based on their respective mole fractions in the product stream.
To learn more about stoichiometry click here: brainly.com/question/32505497
#SPJ11
(a) Calculate the equilibrium constant for the disproportionation reaction 2Cu²+Cu(s) + Cu²+ (aq) at room temperature. Given E°(Cut/Cu) = 0.52 V E°(Cut/Cu²+) = -0.16V (b) Explain mechanism of solid oxide fuel cell. Mention one advantage and one disadvantage of it.
a) At room temperature, we can take the value of the equilibrium constant as 6.6 × 109.
b) The advantages of SOFC are:It can operate on a wide range of fuels, including hydrogen, natural gas, and biogas.It has high efficiency and can generate electricity with up to 60% efficiency and the disadvantages of SOFC are:It operates at high temperatures which leads to thermal degradation.It is expensive as it uses rare metals such as platinum and palladium.
a) Calculation of the equilibrium constant for the disproportionation reaction 2Cu²+Cu(s) + Cu²+(aq) at room temperature is shown below:There are two half-cell reactions involved:Cu²+ + 2e- ⇌ Cu(s) E° = + 0.52 VCu²+ + e- ⇌ Cu+ E° = - 0.16 VAdding these reactions, we get2Cu²+ + Cu(s) ⇌ 3Cu+ E° = 0.52 + (-0.16) = +0.36 VFor the above reaction, the equilibrium constant can be calculated by using the Nernst equation as below:Kc = [Cu+]3/ [Cu²+]2 . [Cu]where [Cu+] is the concentration of Cu+ ions, [Cu²+] is the concentration of Cu²+ ions and [Cu] is the concentration of Cu atoms.At room temperature, we can take the value of the equilibrium constant as 6.6 × 109.
b) Mechanism of solid oxide fuel cell (SOFC)SOFC is a type of fuel cell that operates at high temperatures (between 800 to 1000°C). It consists of two electrodes, an anode and a cathode, separated by an electrolyte. The mechanism involved in the working of SOFC is shown below:At the anode, the fuel (usually hydrogen) is oxidized to produce electrons and protons. This reaction occurs in the presence of a catalyst such as nickel.H2 + 2O2- → 2H2O + 2e-At the cathode, the oxygen from the air is reduced with the help of electrons and protons to produce water.O2 + 4e- + 2H2O → 4OH-The electrons produced in the anode move to the cathode through an external circuit, thus generating electricity.Advantages and disadvantages of SOFC.
The advantages of SOFC are:It can operate on a wide range of fuels, including hydrogen, natural gas, and biogas.It has high efficiency and can generate electricity with up to 60% efficiency.The disadvantages of SOFC are:It operates at high temperatures which leads to thermal degradation.It is expensive as it uses rare metals such as platinum and palladium.
Learn more about temperature here,
https://brainly.com/question/15241334
#SPJ11