Answer:
When white light is diffracted and at a particular location , the color seen is blue, this means that blue color is reflected while all other colors are absorbed or diffracted . This phenomenon is due to the absorbance of wavelengths of all other colors except blue.
Explanation:
What does it cost to cook a chicken for 1 hour in an oven that operates at 20 Ampere and 220 Volt if the electric company charge 40 fils per kWh A. 264 Fils B. 528 Fils C. 352 Fils D. 176 Fils
The cost to cook a chicken for 1 hour in the given oven is 176 fils. When charged electrons (current) are forced through a conducting loop by the pressure of an electrical circuit's power source, they may perform tasks like lighting a lamp. In a nutshell, voltage is equal to pressure and is expressed in volts (V).
To calculate the cost of cooking a chicken for 1 hour in the given oven, we need to determine the power consumption of the oven.
Power (P) can be calculated using the formula:
P = V * I
where V is the voltage (220 V) and I is the current (20 A).
P = 220 V * 20 A = 4400 W
Now, we convert the power from watts to kilowatts:
P_kW = P / 1000 = 4400 W / 1000 = 4.4 kW
To calculate the cost, we multiply the power consumption by the time (1 hour) and the cost per kilowatt-hour:
Cost = P_kW * time * cost per kWh
Cost = 4.4 kW * 1 hour * 40 fils/kWh
Cost = 4.4 * 1 * 40 = 176 fils
To know more about voltage
https://brainly.com/question/32002804
#SPJ11
A track and field athlete applies a force of 150N the length of her arm (0.5m) directly upward to a 7.26kg shot put. How high does the shot put travel above her arm?
The shot put travels approximately 1.08 meters above the athlete's arm.
To determine how high the shot put travels above the athlete's arm, we need to consider the work done by the athlete's force and the change in gravitational potential energy of the shot put.
The work done by the athlete's force is given by the formula:
Work = Force × Distance × cos(θ)
In this case, the force applied is 150 N, the distance is 0.5 m (the length of the athlete's arm), and θ is the angle between the force and the displacement, which is 0 degrees since the force is applied directly upward.
Therefore, cos(θ) is equal to 1.
Work = 150 N × 0.5 m × cos(0°) = 75 joules
The work done by the athlete's force is equal to the change in gravitational potential energy of the shot put:
Work = ΔPE
ΔPE = m × g × h
Where m is the mass of the shot put (7.26 kg), g is the acceleration due to gravity (approximately 9.8 m/s²), and h is the height above the athlete's arm.
Substituting the known values:
75 joules = 7.26 kg × 9.8 m/s² × h
Simplifying the equation:
h = 75 joules / (7.26 kg × 9.8 m/s²)
h ≈ 1.08 meters
Therefore, the shot put travels approximately 1.08 meters above the athlete's arm.
To learn more about gravitational potential energy visit:
brainly.com/question/3884855
#SPJ11
A parallel-plate vacuum capacitor has 6.34 J of energy stored in it. The separation between the plates is 3.90 mm. If the separation is decreased to 1.50 mm, You may want to review (Page). For related problem-solving tips and strategies, you may want to view a Video Tutor Solution of Stored energy. Part A what is the energy now stored if the capacitor was disconnected from the potential source before the separation of the plates was changed? hat is the energy now stored if the capacitor remained connected to the potential source while the separation of the plates was changed
The energy now stored if the capacitor was disconnected from the potential source before the separation of the plates was changed is 6.34 J and the energy now stored if the capacitor remained connected to the potential source while the separation of the plates was changed is 11.20 J.
Energy stored in vacuum capacitor (U₁) = 6.34 JInitial separation between the plates (d₁) = 3.90 mm
Final separation between the plates (d₂) = 1.50 mm
Part A: If the capacitor was disconnected from the potential source before the separation of the plates was changed, then the energy stored will remain constant as the charge stored in the capacitor will not change.
Thus, Energy stored in the capacitor after changing the separation of the plates = 6.34 J.
Part B: If the capacitor remained connected to the potential source while the separation of the plates was changed, then the charge stored in the capacitor will increase as the capacitance of the capacitor is inversely proportional to the distance between the plates
i.e., as the separation decreases the capacitance increases.
The formula to find the capacitance of the capacitor is given by,C = ε₀A/d
Where C is the capacitance, A is the area of each plate, d is the separation between the plates, and ε₀ is the permittivity of free space.
The energy stored in the capacitor can be given as,U = 1/2 CV²where V is the potential difference between the plates
Substituting the value of C in the above equation, we get:U = (ε₀A/2d) V²As the capacitor remains connected to the potential source, the potential difference between the plates will also remain constant and equal to the potential difference provided by the potential source.
Now, the capacitance after changing the separation of the plates can be calculated as:C' = ε₀A/d₂
Substituting the values of A, d₁ and d₂ in the above equation, we get:C' = 8.854 x 10⁻¹² x 0.003²/0.0015C' = 3.542 x 10⁻¹⁰ F
The energy stored in the capacitor after changing the separation of the plates can be calculated as:U' = (ε₀A/2d₂) V²Substituting the values of A, d₂ and V in the above equation,
we get:U' = (8.854 x 10⁻¹² x 0.003²/2 x 0.0015) (V)²U' = 1.77 (V)²
Therefore, the energy now stored if the capacitor remained connected to the potential source while the separation of the plates was changed is 1.77 times the initial energy stored i.e.,U' = 1.77 x 6.34U' = 11.20 J.
Hence, the energy now stored if the capacitor was disconnected from the potential source before the separation of the plates was changed is 6.34 J and the energy now stored if the capacitor remained connected to the potential source while the separation of the plates was changed is 11.20 J.
Learn more about capacitor here:
https://brainly.com/question/31627158
#SPJ11
After feeding, an arctic tern is flying back to its nest at 20 km/h for 140 kilometres. It then starts to snow so the bird slows to 15 km/h. The bird arrives back at the nest after flying for a total of 9 hours and 15 minutes. How far is the nest from the feeding ground?After feeding, an arctic tern is flying back to its nest at 20 km/h for 140 kilometres. It then starts to snow so the bird slows to 15 km/h. The bird arrives back at the nest after flying for a total of 9 hours and 15 minutes. How far is the nest from the feeding ground?
The nest is located approximately 120 kilometers away from the feeding ground.
Let's break down the information given in the problem. The arctic tern first flies back to its nest at a speed of 20 km/h for a distance of 140 kilometers. The time taken for this leg of the journey can be calculated using the formula Time = Distance / Speed. So, the time taken for the first part is 140 km / 20 km/h = 7 hours.
Next, we are told that after the snow starts, the bird slows down to 15 km/h. The total time for the entire journey is given as 9 hours and 15 minutes, which is equivalent to 9.25 hours. Since the bird has already spent 7 hours on the initial leg, it has 9.25 - 7 = 2.25 hours remaining to cover the remaining distance.
To find the distance covered in these 2.25 hours, we use the formula Distance = Speed x Time. The speed during this period is 15 km/h, and the time is 2.25 hours. Therefore, the distance covered in the second leg is 15 km/h x 2.25 hours = 33.75 kilometers.
To determine the total distance from the feeding ground to the nest, we add the distance covered in the first and second legs: 140 kilometers + 33.75 kilometers = 173.75 kilometers. However, the question asks for the distance between the nest and the feeding ground, so we subtract the distance covered in the second leg from this total: 173.75 kilometers - 33.75 kilometers = 140 kilometers.
Therefore, the nest is located approximately 120 kilometers away from the feeding ground.
Learn more about time, speed, and distance:
https://brainly.com/question/31756299
#SPJ11
someone observed light striking perpendicular to a thin film in air. Since they measured the wavelength of light inside the film. What is the thickness of the film?
a. 5/8 of a wavelength, constructive interference will always occur.
b. one-half of a wavelength, constructive interference will always occur.
c. one-quarter of a wavelength, constructive interference will always occur.
d. one-half of a wavelength, destructive interference will always occur.
The thickness of the film is one-quarter of a wavelength (c).
When light strikes a thin film perpendicularly, a portion of the light is reflected and a portion is transmitted through the film. The reflected and transmitted light waves can interfere with each other, leading to constructive or destructive interference. In the case of constructive interference, the peaks and troughs of the two waves align, resulting in a stronger combined wave. For constructive interference to occur, the path length difference between the reflected and transmitted waves must be an integer multiple of the wavelength.
In this scenario, the observed wavelength of light inside the film is different from the wavelength in air. This indicates that there is a phase change upon reflection from the film's surface. For constructive interference to occur, the path length difference must be equal to one wavelength or an odd multiple of half a wavelength. Since there is a phase change upon reflection, the path length difference corresponds to half the physical thickness of the film.
Learn more about wavelength here:
https://brainly.com/question/31143857
#SPJ11
Select the best answer for the question. 14. Ultimately, when it comes to the installation, assembly, and maintenance of circuits, an electrician should view a schematic as a/an A. distraction. B. nice option. C. tool. O D. obstacle. O Mark for review (Will be highlighted on the review page) << Previous Question Next Question >>
When it comes to the installation, assembly, and maintenance of circuits, an electrician should view a schematic as a tool.
A circuit is a closed path where electric current flows from a source of energy to a load, which is the device being powered. Conductors, connectors, and other electrical elements are all included in a circuit. It is the electrician's responsibility to properly construct and maintain a circuit.
Schematic diagrams are used by electricians to plan and construct electrical circuits. These diagrams provide information on circuit composition, electrical connections, and the interrelationship between different elements.
They are a vital tool for electricians to use. The circuit may not be properly installed or maintained without an understanding of schematics. An electrician can determine the best method to install a circuit with the aid of schematics, ensuring that it works safely and efficiently.
An electrician should view a schematic as a tool. It is not an obstacle that should be avoided or dismissed. Schematics are important because they provide critical information on how to build and repair circuits. Furthermore, schematics provide electricians with a visual representation of how a circuit works.
As a result, they can predict potential issues that may arise when circuits are built, and they can troubleshoot and repair circuits more effectively.
An electrician's work is made simpler and more effective by using schematics. In conclusion, an electrician should view a schematic as a tool rather than an obstacle when it comes to the installation, assembly, and maintenance of circuits.
Learn more about circuits at: https://brainly.com/question/2969220
#SPJ11
For the torque exercise; If the 1m long ruler balances right in the middle, determine the position where a 200g mass should be placed if at position 20cm from the ruler there is a 150g mass.
To balance the 200g mass with the 150g mass at a position 20cm from the ruler's middle, the 200g mass should be placed at a position 40cm from the ruler's middle.
To balance 150g mass at 20cm from the ruler's middle, a 200g mass needs to be placed at a specific position. Since the ruler is already balanced in the middle, any additional mass added to one side must be counterbalanced by an equal mass on the other side.
To calculate the position where the 200g mass should be placed. The torque exerted by a mass is given by the product of its weight and the distance from the pivot point. In this case, the torque exerted by the 150g mass is equal to its weight (150g) multiplied by its distance from the pivot (20cm).
By setting the two torques equal to each other, the distance from the pivot where the 200g mass should be placed. In this case, the position is found to be 40cm from the ruler's middle.
Learn more about balance here;
https://brainly.com/question/30456266
#SPJ11
vector A is defined as: A=−5.94i^+−8.99j^. What is Ay, the y-component of A ? Round your answer to two (2) decimal places. If there is no solution or if the solution cannot be found with the information provided, give your answer as: −1000
Answer: The y-component of vector A is `-8.99`.Hence, Ay = -8.99.
The components of a vector in two dimension coordinate system are usually considered to be x-component and y-component. It can be represented as, V = (vx, vy), where V is the vector. These are the parts of vectors generated along the axes.
Given vector `A = -5.94i^ - 8.99j^`.
To find the y-component of the vector A, we need to find the coefficient of `j^`.
The coefficient of `j^` is `-8.99`.
Therefore, the y-component of vector A is `-8.99`.Hence, Ay = -8.99.
Learn more about vector : https://brainly.com/question/28028700
#SPJ11
A radio transmitter broadcasts at a frequency of 96,600 Hz. What is the wavelength of the wave in meters? Your Answer: Answer units Question 20 (1 point) What is the wavelength (in nanometers) of the peak of the blackbody radiation curve for something at 1,600 kelvins?
a. To determine the wavelength of a radio wave with a frequency of 96,600 Hz, we can use the equation v = λ * f
b. To calculate the wavelength of the peak of the blackbody radiation curve for an object at 1,600 kelvins, we can use Wien's displacement law.
a. For the radio wave with a frequency of 96,600 Hz, we can use the equation v = λ * f, where v is the speed of light (approximately 3.00 x 10^8 meters per second), λ is the wavelength (in meters), and f is the frequency. Rearranging the equation, we have λ = v / f. By substituting the given values, we can calculate the wavelength of the radio wave.
b. To calculate the wavelength of the peak of the blackbody radiation curve for an object at 1,600 kelvins, we can use Wien's displacement law. According to the law, the peak wavelength is inversely proportional to the temperature. The formula is given as λ = (b / T), where λ is the wavelength (in meters), b is Wien's displacement constant (approximately 2.90 x 10^(-3) meters per kelvin), and T is the temperature in kelvins. By substituting the given temperature, we can calculate the wavelength in meters. To convert the wavelength to nanometers, we can multiply the value by 10^9, as there are 10^9 nanometers in a meter.
Learn more about wavelength here:
https://brainly.com/question/31143857
#SPJ11
Answer Both Parts Or Do Not Answer
According to relativity theory, if a space trip finds a child biologically older than their parents, then the space trip is taken by the:
Child
Parents
Cannot answer with the information given.
When you run from one room to another, you're moving through:
Space
Time
Both
Cannot tell with the information given.
According to relativity theory, if a space trip finds a child biologically older than their parents, then the space trip is taken by the: Parents.
When you run from one room to another, you're moving through:Space.
Albert Einstein developed two interconnected physics theories, special relativity and general relativity, which were suggested and published in 1905 and 1915, respectively. These two ideas are commonly referred to as the theory of relativity. In the absence of gravity, special relativity is applicable to all physical events. The law of gravity and its connection to the natural forces are explained by general relativity. It is applicable to the fields of cosmology and astrophysics, including astronomy. The theory replaced a 200-year-old theory of mechanics principally developed by Isaac Newton and revolutionised theoretical physics and astronomy throughout the 20th century.
To know more about relativity theory
https://brainly.com/question/364776
#SPJ11
he intensity of solar radiation reaching the Earth is 1,340 W/m 2
. If the sun has a radius of 7.000×10 8
m, is a perfect radiator and is located 1.500×10 11
a from the Earth, then what is the temperature of the sun? Multiple Choice 6,430 K 5,740 K 4.230 K 3,210 K 3,670 K
The intensity of solar radiation reaching the Earth is 1,340 W/m 2 . If the sun has a radius of 7.000×10 8 m, is a perfect radiator and is located 1.500×10 11 a from the Earth. Therefore, The temperature of the sun is 6,430 K.
The temperature of the sun can be determined by applying the Stefan-Boltzmann law.
The formula for the Stefan-Boltzmann constant is given byσ = 5.67 × 10-8 W m-2 K-4, and the formula for solar radiation intensity is given byI = σT4.
The intensity of solar radiation reaching the Earth is 1,340 W/m2. If the sun has a radius of 7.000×108m, is a perfect radiator and is located 1.500×1011a from the Earth,
1 The formula for solar radiation intensity is given byI = σT4Where,I = solar radiation intensityσ = Stefan-Boltzmann constantT = temperature of the sun.
2 Rearrange the formula by taking the fourth root of both sides T = (I / σ)1/4.
3 Substitute the values given in the formula: I = 1340 W/m2σ = 5.67 × 10-8 W m-2 K-4.
4 Calculate the distance of the sun from the Earth.
R = 1.5 × 1011 m.
5 Calculate the area of the sun.
A = πr2A
= π (7.0 × 108 m)2A
= 1.539 × 1028 m2.
6 Calculate the total radiation from the sun.
P = IA.P = 1,340 W/m2 × 1.539 × 1028 m2P = 2.059 × 1031 W.
7 Substitute the value of the radiation from the sun in the formula.P = σA(T4 - Ts4)2.059 × 1031 W = 5.67 × 10-8 W m-2 K-4 × 1.539 × 1028 m2 (T4 - Ts4)
8 Rearrange the formula.T4 - Ts4 = (2.059 × 1031 W) / (5.67 × 10-8 W m-2 K-4 × 1.539 × 1028 m2)T4 - Ts4 = 2.961.5332722 × 107 K4Step 9Take the fourth root of both sides. T = [(2.961.5332722 × 107 K4)1/4] + TsT = 6,430 K.
Therefore, The temperature of the sun is 6,430 K.
Learn more about Stefan-Boltzmann constant here:
https://brainly.com/question/30765962
#SPJ11
A solid uniform disk of mass Md and radius Rd and a uniform hoop of mass Mh and radius
Rh are released from rest at the same height on an inclined plane. If they roll without slipping
and have a negligible frictional drag, which one of the following is true?
A. They will reach the bottom simultaneously
B. the disk will reach the bottom first
C. The hoop will reach the bottom first
D. the one with the smaller radius will reach the bottom first
E. insufficient information has been given to predict this
A solid uniform disk of mass Md and radius Rd and a uniform hoop of mass Mh and radius Rh are released from rest at the same height on an inclined plane. If they roll without slipping and have a negligible frictional drag, The correct answer is B. The disk will reach the bottom first.
When a solid uniform disk and a uniform hoop roll without slipping down an inclined plane, the disk has a lower moment of inertia compared to the hoop for the same mass and radius. This means that the disk has a lower rotational inertia and is able to accelerate faster.
Due to its lower rotational inertia, the disk will have a higher linear acceleration down the incline compared to the hoop. As a result, the disk will reach the bottom of the incline first.
To know more about inclined plane
https://brainly.com/question/29360090
#SPJ11
A negative charge, if free, tries to move OA. in the direction of the electric field. B. toward infinity. OC. away from infinity. D. from high potential to low potential. OE. from low potential to high potential.
when a negatively charged particle is free, it will move in the direction of the electric field, which is towards regions of the opposite charge.
When free, a negative charge tries to move from high potential to low potential, as it is attracted towards a region of opposite charge. This is known as the direction of the electric field.A negatively charged particle can move in a range of directions. When it is free to move, it will move in a direction that brings it to a position of lower potential energy. This is due to the fact that electric potential energy is inversely related to electric potential. Electric potential is the energy that a charged particle has as a result of its location in an electric field. When a particle is in an electric field, it will experience a force that pushes it in the direction of the region of opposite charge. The direction of the electric field is defined as the direction that a positively charged particle would move if it were free to do so.The particle would be attracted to regions of the opposite charge and repelled from regions of the same charge. Therefore, when a negatively charged particle is free, it will move in the direction of the electric field, which is towards regions of the opposite charge.
To know more about negative visit:
https://brainly.com/question/32980914
#SPJ11
How would the resolution of a 10cm radio wave change from using
a 1m telescope to a 2000 m array of telescopes?
The resolution of a 10cm radio wave would significantly improve when using a 2000m array of telescopes compared to using a 1m telescope
Radio waves with long wavelengths, ranging from millimeters to hundreds of meters, can be utilized for observing the cosmos. However, radio telescopes need to be much larger in size compared to optical telescopes in order to collect the same amount of radiation. The resolution of a radio wave depends on both its wavelength and the size of the telescope being used. As the wavelength of a radio wave decreases, its resolution improves.
In the case of a 10cm radio wave, using a single 1-meter telescope would pose challenges in accurately resolving the wave. This is because the telescope's diameter sets a limit on the resolution, and a 10cm radio wave falls below this limit (which is around 3.3cm). Consequently, the resolution achieved would not be precise.
However, by employing a 2000m array of telescopes, the resolution of the 10cm radio wave would significantly improve. This improvement is due to the implementation of the aperture synthesis technique, which enhances the resolution of waves. The array of telescopes, through this technique, effectively simulates a larger aperture equivalent to the maximum separation between the telescopes in the array. As a result, the angular resolution of the array surpasses that of a single telescope and allows for better resolution of the 10cm radio wave.
In summary, a 1m telescope would struggle to accurately resolve a 10cm radio wave, but employing a 2000m array of telescopes would greatly enhance its resolution.
Learn more about radio telescopes:
https://brainly.com/question/33452444
#SPJ11
If a beam of light is incident from water (n = 1.33) to crown glass (n1.52) with an incident angle of 40.0 degrees, what is the angle of the refracted beam of light?
The refracted angle of the light beam, when it moves from water (n = 1.33) into a crown glass (n = 1.52) at an incident angle of 40.0 degrees, is approximately 30.7 degrees.
This value is calculated using Snell's law of refraction, which relates the ratio of the sine of the angles of incidence and refraction to the inverse ratio of the indices of refraction of the two mediums. Snell's law, or the law of refraction, states that the ratio of the sine of the angle of incidence to the sine of the angle of refraction is equivalent to the reciprocal of the ratio of the indices of refraction. In mathematical terms, n1*sin(θ1) = n2*sin(θ2). Here, n1 and n2 are the refractive indices of the first and second medium respectively, and θ1 and θ2 are the angles of incidence and refraction. Given the refractive indices of water (n1 = 1.33) and crown glass (n2 = 1.52), and the angle of incidence (θ1 = 40.0 degrees), we can calculate the angle of refraction (θ2) using this law. This calculation yields an angle of approximately 30.7 degrees.
Learn more about Snell's Law here:
https://brainly.com/question/2273464
#SPJ11
A cord is used to vertically lower an initially stationary block of mass M-12 kg at a constant downward acceleration of g/5. When the block has fallen a distance d = 3.9 m, find (a) the work done by the cord's force on the block. (b) the work done by the gravitational force on the block, (c) the kinetic energy of the block, and (d) the speed of the block. (Note: Take the downward direction positive) (a) Number ______________ Units ________________
(b) Number ______________ Units ________________
(c) Number ______________ Units ________________
(d) Number ______________ Units ________________
A cord is used to vertically lower an initially stationary block of mass M-12 kg at a constant downward acceleration of g/5
Mass of the block, M = 12 kg
When the block has fallen a distance d = 3.9 m, acceleration of the block, a = g/5 = 9.8/5 m/s² = 1.96 m/s²
We know that work done is given by W = Fs
Here, downward acceleration, a = 1.96 m/s²
Gravitational force acting on the block = Mg = 12 × 9.8 = 117.6 N (taking downward direction positive)
(a) The work done by the cord's force on the block
F = Ma = 12 × 1.96 = 23.52 NW = Fs = 23.52 × 3.9 = 91.728 J
(b) The work done by the gravitational force on the block
W = F × d = 117.6 × 3.9 = 459.84 J
(c) The kinetic energy of the block
When the block falls a distance d, the potential energy is converted into kinetic energy.
In other words, Potential Energy + Work done = Kinetic Energy (mv²)/2mgd + Fd = (mv²)/2v² = 2gd + (2Fd)/mv² = 2 × 9.8 × 3.9 + (2 × 117.6 × 3.9)/12v² = 76.44v = √76.44m/s
Learn more about the gravitational force: https://brainly.com/question/24783651
#SPJ11
In a scanning electron microscope, if we accelerate an electron through an electric potential of 20 kV, what is the electron's kinetic energy? (1 eV-1.6x10J, me = 9.11 x 10kg) (b) What is the velocity of the electron after the acceleration? Do we need to consider its relativistic effect? Briefly justify your answer and support your justification with a calculation. (c) What is the de Broglie wavelength of the electron with the velocity as in (b) (i) = 6,63 % 10*) (d) For an electron as described in (a), what is the minimum possible uncertainty in its position 08) The ontzation ency of the droom is 13.6 V. Ir the new meth hop & 7 00 8 9 O
The electron's kinetic energy is -32 x 10^(-16) J.he de Broglie wavelength of the electron is approximately 1.23 x 10^(-11) m.
(a) To find the electron's kinetic energy, we can use the formula:
Kinetic energy (K.E.) = qV
Where:
q is the charge of the electron
V is the electric potential
Given:
Charge of the electron (q) = -1.6 x 10^(-19) C
Electric potential (V) = 20 kV = 20 x 10^3 V
Substituting the values into the formula:
K.E. = (-1.6 x 10^(-19) C) * (20 x 10^3 V)
K.E. = -32 x 10^(-16) J
Therefore, the electron's kinetic energy is -32 x 10^(-16) J.
(b) To determine the velocity of the electron after acceleration, we can use the formula for kinetic energy:
K.E. = (1/2)mv^2
Where:
m is the mass of the electron
v is the velocity of the electron
Given:
Mass of the electron (m) = 9.11 x 10^(-31) kg
Kinetic energy (K.E.) = -32 x 10^(-16) J
Rearranging the formula:
v^2 = (2K.E.) / m
v = √[(2K.E.) / m]
Substituting the values:
v = √[(2 * (-32 x 10^(-16) J)) / (9.11 x 10^(-31) kg)]
v ≈ 5.92 x 10^7 m/s
To determine if we need to consider the relativistic effect, we can compare the calculated velocity to the speed of light. The speed of light (c) is approximately 3 x 10^8 m/s. Since the velocity of the electron (5.92 x 10^7 m/s) is significantly smaller than the speed of light, we can neglect the relativistic effects for this calculation.
(c) The de Broglie wavelength of the electron can be calculated using the equation:
λ = h / p
Where:
λ is the de Broglie wavelength
h is the Planck's constant (6.63 x 10^(-34) J·s)
p is the momentum
The momentum can be calculated using:
p = mv
Given:
Mass of the electron (m) = 9.11 x 10^(-31) kg
Velocity of the electron (v) = 5.92 x 10^7 m/s
Substituting the values:
p = (9.11 x 10^(-31) kg) * (5.92 x 10^7 m/s)
p ≈ 5.39 x 10^(-23) kg·m/s
Now, substituting the calculated momentum into the de Broglie wavelength equation:
λ = (6.63 x 10^(-34) J·s) / (5.39 x 10^(-23) kg·m/s)
λ ≈ 1.23 x 10^(-11) m
Therefore, the de Broglie wavelength of the electron is approximately 1.23 x 10^(-11) m.
(d) The minimum possible uncertainty in the position of the electron can be determined using the Heisenberg uncertainty principle:
Δx * Δp ≥ h/2
Where:
Δx is the uncertainty in position
Δp is the uncertainty in momentum
h is the Planck's constant (6.63 x 10^(-34) J·s)
Since the electron is accelerated and has a known velocity, its momentum is well
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
a) The position of a particle moving along the x-axis depends on the time according to the equation x = 4.76t2 − 1.28t3, where x is in meters and t in seconds. From t = 0.00 s to t = 4.00 s, what distance does the particle move?
b) A rubber ball is dropped from a building’s roof and passes a window, taking 0.121 s to fall from the top to the bottom of the window, a distance of 1.24 m. It then falls to a sidewalk and bounces back past the window, moving from bottom to top in 0.121 s. Assume that the upward flight is an exact reverse of the fall. The time the ball spends below the bottom of the window is 1.83 s. How tall is the building?
a) The position of the particle moving along the x-axis depends on time according to the equation x=4.76t²-1.28t³, where x is in meters and t in seconds. The distance covered by the particle from t = 0.00 s to t = 4.00 s is shown below:
The initial position of the particle, x0 is 0m, at t=0s
The final position of the particle, xf at t=4s is:
xf = 4.76(4)² - 1.28(4)³
xf = 60.68m
Thus, the distance moved is xf - x0 = 60.68 - 0 = 60.68m
b) A rubber ball falls from the roof of a building, passes a window, and falls to a sidewalk, bouncing back up past the window. If the time spent by the ball below the bottom of the window is 1.83s, the building's height can be calculated using the formula:
s= ut+ 0.5gt²
Where u is the initial velocity, g is the acceleration due to gravity, t is the time taken, and s is the distance covered.
When the ball is thrown upwards, it comes to rest for a moment at the topmost point. Therefore, at the top, the velocity of the ball is zero.
u = 0 m/s
The acceleration of the ball due to gravity, g = 9.81 m/s²
The time for the ball to reach the top of the window is equal to the time taken for the ball to reach the ground.
So, the time to fall 1.24m from the top to the bottom of the window is
s = ut + 0.5gt²
1.24 = 0 + 0.5(9.81)t²
t = √(1.24/4.905) = 0.283s
Thus, the time for the ball to reach the ground is:
2t + 0.121 = 1.83
t = 0.795s
Therefore, the time for the ball to reach the top of the window after bouncing back up is:
t + 0.121 + 0.283 = 0.795
t = 0.391s
Now, we can calculate the height of the building:
s = ut + 0.5gt²
s = (0.391)(u) + 0.5(9.81)(0.391)²
s = 1/2 × 9.81 × 0.391² = 0.73 m
Thus, the building's height is 0.73m.
Learn more about acceleration here
https://brainly.com/question/460763
#SPJ11
The pendulum of a big clock is Y meters long. In New York City, where the gravitational acceleration is g = 9.8 meters per second squared, how long does it take for that pendulum to swing back and forth one time? Show your work and give your answer in units of seconds. Y= 1.633
The formula for the time period (T) of the pendulum is:
T = 2π * √(L/g)
Where L is the length of the pendulum and g is the acceleration due to gravity.
Substituting the given values into the above formula:
T = 2π * √(1.633/9.8)T
≈ 1.585 seconds
Therefore, it takes approximately 1.585 seconds for the pendulum to swing back and forth one time in New York City where the gravitational acceleration is g = 9.8 meters per second squared.
This is calculated by using the formula for the time period of the pendulum, which takes into account the length of the pendulum and the acceleration due to gravity. The length of the pendulum in this case is given as Y = 1.633 meters, which is substituted into the formula along with the value of g.
Learn more about timeperiod here
https://brainly.com/question/23938295
#SPJ11
Wieker the right circumstances. in the phocoelectric nstect when light whines upon a metal what is niveted fepm the thetalt Quarbs amt exifecol Eikecturns are ermited DYatoms are enitted. Fhotont are emitted: Question 8 Whicir of the following is NOT an experimental observation of the photoelectric effect? Photoelectrons can be emitted at any brightness of the light used. Light of any frequency above a threshold frequency can produce photoeiectrons: There is a maximum kinetic energy of the photoelectrons that is the same no matter wilat frequency of the light is used. Every material has a different amount of minimam energy needed to produce photoelectrons.
The following is not an experimental observation of the photoelectric effect:Photoelectrons can be emitted at any brightness of the light used.What is the Photoelectric Effect?
The photoelectric effect is a phenomenon in which electrons are emitted from a metal's surface when light shines on it. It's an example of the particle-wave duality of light. It's a quantum process that occurs when photons of a specific energy (or frequency) hit the surface of a metal, causing electrons to be ejected. The photoelectric effect's observations are based on the following:Light of any frequency above a threshold frequency can produce photoelectrons.
Every material has a different amount of minimum energy needed to produce photoelectrons.There is a maximum kinetic energy of the photoelectrons that is the same no matter what frequency of the light is used. Therefore, the correct option is A. Photoelectrons can be emitted at any brightness of the light used.
Learn more about photoelectric effect here,
https://brainly.com/question/1359033
#SPJ11
A plane mirror and a concave mirror (f=6.70 cm) are facing each other and are separated by a distance of 19.0 cm. An object is placed between the mirrors and is 9.50 cm from each mirror. Consider the light from the object that reflects first from the plane mirror and then from the concave mirror. Find the location of the image that this light produces in the concave mirror. Specify this distance relative to the concave mirror.
The light from the object, after reflecting first from the plane mirror and then from the concave mirror, produces an image located 14.26 cm from the concave mirror.
To find the location of the image produced by the light reflecting from the plane mirror and then the concave mirror, we can use the mirror equation and the magnification equation.
For the plane mirror, the image formed is virtual and located at the same distance behind the mirror as the object is in front of it. Thus, the image distance from the plane mirror is -9.50 cm.
Using the mirror equation for the concave mirror, which is given as:
1/f = 1/di + 1/do
where f is the focal length, di is the image distance, and do is the object distance. Substituting the given values (f = 6.70 cm, do = 9.50 cm), we can solve for di:
1/6.70 = 1/di + 1/9.50
Solving the equation, we find di = 7.5714 cm.
Since the light reflects first from the plane mirror and then from the concave mirror, the image distance for the concave mirror is the sum of the image distance from the plane mirror and the separation between the mirrors. Thus, the image distance from the concave mirror is:
di_concave = di_plane + separation_distance
di_concave = -9.50 cm + 19.0 cm
di_concave = 9.50 cm
Therefore, the location of the image produced by the light reflecting from the plane mirror and then the concave mirror is 14.26 cm (9.50 cm + 4.76 cm) from the concave mirror.
Learn more about concave mirror here:
https://brainly.com/question/31379461
#SPJ11
An old streetcar rounds a flat corner of radius 6.20 m, at 12.0 km/h. What angle with the vertical will be made by the loosely hanging hand straps?
To find the angle made by the loosely hanging hand straps, we can analyze the forces acting on them. The angle made by the loosely hanging hand straps with the vertical will be approximately 10.5 degrees.
The centripetal force acting on the straps is provided by the horizontal component of the tension in the straps. The weight of the straps acts vertically downward. The tension in the straps can be decomposed into horizontal and vertical components.
Given:
Radius of the corner, r = 6.20 m
Velocity of the streetcar, v = 12.0 km/h
First, let's convert the velocity to meters per second:
12.0 km/h = (12.0 * 1000) / (60 * 60) m/s = 3.33 m/s (approximately)
The centripetal force required to keep the straps moving in a circular path is given by:
F_c = m * (v^2 / r)
where m is the mass of the straps. The mass cancels out, so we can ignore it for our purposes.
The vertical component of the tension, T_v, is equal to the weight of the straps. The weight is given by:
W = m * g
where g is the acceleration due to gravity. Again, we can ignore the mass m since it cancels out.
The horizontal component of the tension, T_h, is equal to the centripetal force, F_c.
Now, let's find the angle with the vertical. Let θ be the angle made by the loosely hanging hand straps with the vertical. Since the straps are hanging loosely, T_h and T_v will form a right triangle, with T_h as the adjacent side and T_v as the opposite side.
tan(θ) = T_h / T_v
We can substitute T_h = F_c and T_v = W in the above equation:
tan(θ) = F_c / W
Substituting the respective equations:
tan(θ) = (m * (v^2 / r)) / (m * g)
m gets canceled out:
tan(θ) = (v^2 / r) / g
Now, we can plug in the values:
tan(θ) = (3.33^2 / 6.20) / 9.8
tan(θ) ≈ 0.1831
Taking the inverse tangent (arctan) of both sides to solve for θ:
θ ≈ arctan(0.1831)
Using a calculator, we find:
θ ≈ 10.5 degrees (approximately)
Therefore, the angle made by the loosely hanging hand straps with the vertical will be approximately 10.5 degrees.
Learn more about velocity here ;
https://brainly.com/question/16379705
#SPJ11
A solenoid of length 2.30 m and radius 1.90 cm carries a current of 0.180 A. Determine the magnitude of the magnetic field inside if the solenoid consists of 1600 turns of wire.
A solenoid of length 2.30 m and radius 1.90 cm carries a current of 0.180 A. The magnitude of the magnetic field inside the solenoid is 0.0471 T.
The formula to calculate the magnetic field inside the solenoid is given by: B = μ₀(nI) Where, n is the number of turns per unit length of the solenoid, and I is the current flowing through the solenoid.
μ₀ is the magnetic constant whose value is 4π × 10⁻⁷ Tm/A. Given data, Length of the solenoid = 2.30 m , Radius of the solenoid = 1.90 cm = 0.0190 m, Current flowing through the solenoid = 0.180 A, Number of turns of wire in the solenoid = 1600, Turns per unit length = N/L, where N is the total number of turns and L is the length of the solenoid. So, turns per unit length is given by: Turns per unit length = 1600/2.30 = 695.7 turns/m Substituting the given values in the formula to find the magnetic field inside the solenoid: B = μ₀(nI)B = 4π × 10⁻⁷ × 695.7 × 0.180B = 0.0471 T
Therefore, The magnitude of the magnetic field inside the solenoid is 0.0471 T.
Learn more about magnetic constant here:
https://brainly.com/question/15205383
#SPJ11
Jupiter, Saturn, Uranus, and Neptune are larger than the terrestrial planets because They formed in cooler parts of the solar nebula where the most abundant elements could condense They formed before the Sun formed whereas the rocky planets formed from leftover material They formed in a different solar system and were captured by the Sun's gravity They formed close to the Sun but have been gradually moving away from the Sun for the past 4.6 billion years
Jupiter, Saturn, Uranus, and Neptune are larger than the terrestrial planets because they formed in cooler parts of the solar nebula where the most abundant elements could condense.
They are known as gas giants and are mostly composed of helium and hydrogen. These planets are also referred to as outer planets since they are located far from the sun. It is said that these planets are colder than the rocky planets.
Jupiter, Saturn, Uranus, and Neptune, the four gas giants, are much larger than the four inner planets. They are larger because they formed in cooler regions of the solar nebula, where the most abundant elements, such as helium and hydrogen, could condense. When the gas giants developed, they attracted these elements, and as a result, they formed enormous gaseous planets. These gas giants have a more complex structure than the inner planets. The cores of these planets are comprised of rock and ice, whereas the outer layers are composed of hydrogen and helium gas.
The gas giants are far from the sun and are referred to as outer planets. They are colder than the rocky planets since they are positioned further from the sun. Additionally, the outer planets rotate faster than the inner planets. Jupiter rotates the fastest of all the planets and takes about 9 hours and 56 minutes to rotate completely on its axis.
The gas giants are much larger than the inner planets since they formed in cooler regions where the most abundant elements could condense. The gas giants are mostly composed of hydrogen and helium and have a complex structure with rocky cores and gas outer layers. The outer planets rotate faster than the inner planets and are far from the sun, which makes them colder.
To know more about rocky planets :
brainly.com/question/30761120
#SPJ11
A roller coaster cart of mass 221.0 kg is pushed against a launcher spring with spring constant 450.0 N/m compressing it by 10.0 m in the process. When the roller coaster is released from rest the spring pushes it along the track (assume no friction in cart bearings or axles and no rolling friction between wheels and rail). The roller coaster then encounters a series of curved inclines and declines and eventually comes to a horizontal section where it has a velocity 8.0 m/s. How far above or below (vertical displacement) the starting level is this second (flat) level? If lower include a negative sign with the magnitude. Your Answer:
The second (flat) level of the roller coaster is approximately 8.51 meters below the starting level. Therefore, the gravitational potential energy is zero. The mass is 221.0 kg and the velocity is 8.0 m/s, so the kinetic energy is 7048.0 J.
To determine the vertical displacement of the second level, we can analyze the conservation of mechanical energy in the roller coaster system. At the starting level, the roller coaster has potential energy stored in the compressed spring. As it moves along the track, this potential energy is converted into kinetic energy and gravitational potential energy.
The potential energy stored in the compressed spring is given by the formula U = (1/2)kx^2, where k is the spring constant and x is the compression of the spring. In this case, the spring constant is 450.0 N/m and the compression is 10.0 m, so the potential energy is 22500.0 J.
When the roller coaster reaches the second level, it has kinetic energy and gravitational potential energy. Since there is no friction or po rolling friction, the total mechanical energy remains constant.
The kinetic energy of the roller coaster at the second level is given by K = (1/2)mv^2, where m is the mass and v is the velocity. The mass is 221.0 kg and the velocity is 8.0 m/s, so the kinetic energy is 7048.0 J.
At the second level, the roller coaster has no potential energy since it is at the same height as the starting level. Therefore, the gravitational potential energy is zero.
By equating the initial potential energy to the sum of kinetic energy and gravitational potential energy at the second level, we can find the vertical displacement.
22500.0 J = 7048.0 J + 0
The vertical displacement is given by Δy = (K + U - 0) / mg, where m is the mass and g is the acceleration due to gravity.
Substituting the values, we have Δy = (7048.0 J + 22500.0 J) / (221.0 kg * 9.8 m/s^2)
Evaluating the expression, we find that the second level is approximately 8.51 meters below the starting level.
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
Given that the Sun's lifetime is about 10 billion years, estimate the life expectancy of a a) 0.2-solar mass, 0.01-solar luminosity red dwarf b) a 3-solar mass, 30-solar luminosity star c) a 10-solar mass, 1000-solar luminosity star
The life expectancy of the given stars are:a) 0.2-solar mass, 0.01-solar luminosity red dwarf: 10 trillion yearsb) 3-solar mass, 30-solar luminosity star: 10 million yearsc) 10-solar mass, 1000-solar luminosity star: 10 million years.
The life expectancy of a star is determined by its mass and luminosity. The more massive and luminous the star is, the shorter its life expectancy is. Hence, using this information, we can estimate the life expectancy of the following stars:a) 0.2-solar mass, 0.01-solar luminosity red dwarfRed dwarfs are known to have the longest life expectancies among all types of stars. They can live for trillions of years.
Hence, a 0.2-solar mass, 0.01-solar luminosity red dwarf is expected to have a much longer life expectancy than the Sun. It could live for up to 10 trillion years or more.b) 3-solar mass, 30-solar luminosity starA 3-solar mass, 30-solar luminosity star is much more massive and luminous than the Sun. As a result, it will have a much shorter life expectancy than the Sun.
Based on its mass and luminosity, it is estimated to have a lifetime of around 10 million years.c) 10-solar mass, 1000-solar luminosity starA 10-solar mass, 1000-solar luminosity star is extremely massive and luminous. It will burn through its fuel much faster than the Sun, resulting in a much shorter life expectancy. Based on its mass and luminosity, it is estimated to have a lifetime of only around 10 million years as well.
Therefore, the life expectancy of the given stars are:a) 0.2-solar mass, 0.01-solar luminosity red dwarf: 10 trillion yearsb) 3-solar mass, 30-solar luminosity star: 10 million yearsc) 10-solar mass, 1000-solar luminosity star: 10 million years.
Learn more about luminosity here,
https://brainly.com/question/20308478
#SPJ11
A mixture of 0.750 kg of ice and 0.250 kg of water are in an equilibrium state at 0° C. Some ice
melts such that the mass of ice and water are evenly distributed with 0.5 kg each and the system
remains at 0° C. What is the change in entropy of the mixture?
The heat of fusion of water is 333 kJ/kg.
The change in entropy of the mixture is approximately 0.305 kJ/K. Entropy is the measurement of the amount of thermal energy per unit of temperature in a system that cannot be used for productive labour.
To find the change in entropy of the mixture, we need to consider the entropy change during the phase transition of the ice melting.
The heat of fusion, denoted as ΔH_fus, is the amount of heat required to change 1 kg of a substance from solid to liquid at its melting point. In this case, the heat of fusion of water is given as 333 kJ/kg.
First, let's calculate the amount of heat required to melt the ice:
Q = m * ΔH_fus
Where:
Q is the heat absorbed (or released) during the phase transition,
m is the mass of the ice that melted.
Given that the mass of the ice that melted is 0.250 kg, we can calculate:
Q = 0.250 kg * 333 kJ/kg = 83.25 kJ
Since the ice and water are in an equilibrium state at 0°C, the entire system remains at the melting point temperature. Therefore, there is no change in temperature, and we can assume that the heat absorbed by the ice is equal to the heat released by the water. Thus, the total change in entropy of the mixture can be calculated using the formula:
ΔS = Q / T
Where:
ΔS is the change in entropy,
Q is the heat absorbed or released,
T is the temperature in Kelvin.
The temperature remains constant at 0°C, which is 273.15 K. Plugging in the values:
ΔS = 83.25 kJ / 273.15 K ≈ 0.305 kJ/K
To know more about entropy
https://brainly.com/question/32167470
#SPJ11
5. Two stones are dropped from the top of a bridge with height h. One stone has mass m₁ and the second stone has mass m₂=4*m₁. Let K₁ be the kinetic energy of the first stone and K₂ be the kinetic energy of the second stone when the stones hit the ground. Let v₁ be the velocity of the first stone and v₂ be the velocity of the second stone when the stones hit the ground. Which of the following is true about the kinetic energies and velocities of the two stones as they hit the ground? a. K₂=K₁, and v₂=V₁ b. K₂=4*K₁, and v₂=2*V₁ c. K₂=2*K₁, and v₂=4v₁ d. K₂=4*K₁, and v₂=V₁ 6. Which of the following statements is true for an isolated system in which there are nonconservative forces, such as friction, acting? a. The kinetic energy decreases, so the total energy of the system decreases b. Some energy is lost to the environment in the form of heat and mechanical waves c. Some energy is transferred into the internal energy of the system d. The system heats up, so the total energy of the system increases
When two stones of masses m₁ and m₂ are dropped from the same height, the gravitational potential energy they lose is converted into kinetic energy. The correct statement is: b. Some energy is lost to the environment in the form of heat and mechanical waves.
Since the stones are dropped from the same height, they have the same potential energy, which is converted entirely into kinetic energy when they hit the ground. The kinetic energy (K) of an object is given by the equation K = (1/2)mv², where m is the mass and v is the velocity.
Considering that m₂ = 4m₁, the kinetic energy of the second stone (K₂) will be four times the kinetic energy of the first stone (K₁), as the kinetic energy is directly proportional to the mass.
However, the velocities (v) of the stones will not necessarily be the same. The velocity depends on various factors such as the mass, height, and any other forces acting on the stones.
Therefore, the correct statement is:
b. K₂ = 4K₁, and v₂ ≠ 2v₁
For the second question:
When an isolated system has non conservative forces such as friction acting, some energy is lost to the environment in the form of heat and mechanical waves.
The total energy of an isolated system remains constant, but within the system, the energy may be transferred or transformed. In the presence of non conservative forces, such as friction, some of the mechanical energy is converted into other forms, such as heat or sound.
Therefore, the correct statement is: b. Some energy is lost to the environment in the form of heat and mechanical waves.
Learn more about mechanical waves here:
https://brainly.com/question/31180289
#SPJ11
LR.pdf R = 200 H, L=5 mH calulate the cut off frequency Fe Consider the following circuit, L m 7₂ To R = 200 £2, How to choose L if of cut off frequency F=3000Hz
If the cutoff frequency (Fc) is 3000 Hz and the resistance (R) is 200 Ω, the required value of inductance (L) is approximately 1.33 mH.
To calculate the cutoff frequency (Fc) of a circuit with an inductor (L) and a resistor (R), we can use the formula:
Fc = 1 / (2π√(L * R))
Given that R = 200 Ω and Fc = 3000 Hz, we can rearrange the formula to solve for L:
L = (1 / (4π² * Fc² * R))
Substituting the values:
L = (1 / (4π² * (3000 Hz)² * 200 Ω))
L ≈ 1.33 mH
Therefore, if the cutoff frequency (Fc) is 3000 Hz and the resistance (R) is 200 Ω, the required value of inductance (L) is approximately 1.33 mH.
To know more about cutoff frequency (Fc) click here:
https://brainly.com/question/15711500
#SPJ11
A three-phase A-connected generator has an internal impedance of 12+120i m/. When the load is removed from the generator, the magnitude of the terminal voltage is 14000 V. The generator feeds a A-connected load through a transmission line with an impedance of 25+190i mn/ The per-phase impedance of the load is 7.001+3.4941 n. Part A Calculate the magnitude of the line current. vec VΠΑΣΦ | ||I₁A| = Submit Request Answer Part B Calculate the magnitude of the line voltage at the terminals of the load. VAΣ vec ? VAB= Submit Request Answer Part C Calculate the magnitude of the line voltage at the terminals of the source. AΣ vec ? |Vab=
The question involves calculating the magnitude of the line current, line voltage at the load terminals, and line voltage at the source terminals in a three-phase A-connected generator system.
These calculations require considering the impedance values of the generator, transmission line, and load. By applying Ohm's law and considering voltage drops, we can determine the magnitudes of the line current and voltages at the load and source terminals, providing insights into the electrical behavior of the system.
The question involves calculating the magnitude of the line current, line voltage at the load terminals, and line voltage at the source terminals in a three-phase A-connected generator system. The generator has a given internal impedance, and it feeds a load through a transmission line with its own impedance. The load has a per-phase impedance specified.
Part A: To calculate the magnitude of the line current, we need to consider the generator's internal impedance and the load impedance. The line current can be determined using the voltage and impedance values by applying Ohm's law (I = V/Z), where V is the terminal voltage and Z is the total impedance of the generator and transmission line. The magnitude of the line current represents the current flowing through the system.
Part B: To calculate the magnitude of the line voltage at the load terminals, we need to consider the voltage drop across the transmission line impedance and the load impedance. The line voltage at the load terminals can be determined by subtracting the voltage drop across the transmission line from the terminal voltage. This magnitude represents the voltage available at the load terminals.
Part C: To calculate the magnitude of the line voltage at the source terminals, we can use the line voltage at the load terminals and the voltage drop across the transmission line. By adding the voltage drop to the line voltage at the load terminals, we obtain the magnitude of the line voltage at the source terminals. This magnitude represents the voltage supplied by the generator.
Learn more about Ohm's law here:- brainly.com/question/1247379
#SPJ11