Answers
Answers: 1) 3 kg m²
2) 2.88 kg m²
Explanation: Question 1
I = m(r)²+ M(r)²
I = 1.2 kg × (1 m )² +1.8 kg ×(1 m )²
∴ I = 3 kg m²
Question 2
ACCORDING TO THE DIAGRAM DRAWN FOR QUESTION 2
we have to decide where the center of gravity (G) lies and obviously it should lie somewhere near to the greater mass. (which is 1.8 kg). Since we don't know the distance from center of gravity(G) to the mass (1.8 kg) we'll take it as 'x' and solve!!
moments around 'G'
F₁ d ₁ = F₂ d ₂
12 (2-X) = 18 (X)
24 -12 X =18 X
∴ X = 0.8 m
∴ ( 2 - x ) = 1.2 m
∴ Moment of inertia (I) going through the center of mass of two masses,
⇒ I = m (r)² +M (r)²
⇒ I = 1.2 × (1.2)² + 1.8 × (0.8)²
⇒ I = 1.2 × 1.44 + 1.8 × 0.64
⇒ I = 1.728 + 1.152
⇒ ∴ I = 2.88 kg m²
∴ THE QUESTION IS SOLVED !!!
Related Questions
in the figure if coefficient of friction between block and surface is 0.2 then find acceleration produced by the resultant force acting on the block (take g= 10 m/s²)
Answers
☃ First of all we have to calculate frictional force by using below equation :
→ F = μR
→ F = 0.2 × 5 × 10
→ F = 10 N
Hence,the frictional force (F) is 10 N.☃ But we know that frictional force is acting on opposite direction of the motion :
⇏Net force = 15 - 10
⇏Net force = 5 N
Hence,the net force is 5 N.☃ By using Newton's second law we get :
Let the required acceleration produced by the block be 'a'.➝ Force = mass × acceleration
➝ 5 = 5 × a
➝ a = 5 ÷ 5
➝ a = 1 m/s²
Hence,the acceleration produced by the resultant force acting on the block is 1 m/s².Which best describes the law of conservation of mass?
O The coefficients in front of the chemicals in the reactants should be based on the physical state of the products,
O Products in the form of gases are not considered a part of the total mass change from reactants to products
O When reactants contain both a solid and a liquid, the solid counts toward the overall mass and the liquid does not
O The mass of the reactants and products is equal and is not dependent on the physical state of the substances.
Answers
Explanation:
The law of conservation of mass states that mass in an isolated system is neither created nor destroyed by chemical reactions or physical transformations. According to the law of conservation of mass, the mass of the products in a chemical reaction must equal the mass of the reactants.
A hammer strikes a nail with a 10N force for .01 seconds. Calculate the impulse of the hammer
Answers
Answer:
Impulse = 0.1 Kgm/s
Explanation:
Given the following data;
Force, F = 10N
Time, t = 0.01 seconds
To find impulse
An impulse can be defined as the net force acting an object for a very short period of time.
Mathematically, impulse is given by the formula;
Impulse = force * time
Substituting into the equation, we have;
Impulse = 10 * 0.01
Impulse = 0.1 kgm/s
Therefore, the impulse of the hammer is 0.1 kilogram meter per seconds.
The impulse of the hammer is 0.1 Ns.
To solve the given problem we need to use the formula for calculating impulse.
Impulse: This can be defined as the product of force and time on a body.
The formula of impulse is given below.
I = Ft....................... Equation 1
Where :
I = Impulse of the harmerF = Force on the nailt = timeFrom the question,
Given:
F = 10 Nt = 0.01 sSubstitute these values into equation 1
I = 10(0.01)I = 0.1 NsHence, The impulse of the hammer is 0.1 Ns.
Learn more about force here: https://brainly.com/question/13370981
A bicyclist is riding a constant speed 62.0 seconds for 200. meters what is his average speed
Answers
Answer:
Explanation::
A 2800 kg speedboat starting from rest attains a speed of 16 m/s in 8.0 s as a combination of 1200 N of air resistance and water drag act on the boat. How much power is being expended by speedboat at the maximum speed?
Answers
Answer:
For me
Explanation:
first of all
find the distance=speed×time
16×8=128
power= workdone /time
power=force×distance/time
power=1200×128/8
power=153600/8
powere=19200
It is now 9:11 a.m. but when the bell rings at 9:12 a.m. Susie will be late for Mrs. Garner's U.S. History class for the 3rd time this week. She must get from one side of the school to the other by hurrying down three different hallways. She runs down the first hallway (D-Hall), a distance of 47.0 meters. The second hallway (C-Hall) is filled with students, and she covers its 63.0 m length quickly. The final hallway (B- Hall) is empty, and Susie sprints its 76.0 m length. How fast does Susie need to go to make it to class on time (Hint: Calculate the total distance. Then calculate her total average speed rounded to the nearest tenths in meters/seconds.)?
Answers
Answer:
3.1 m/s
Explanation:
The total distance she has to run is the addition of the three lengths:
47 + 63 + 76 = 186 meters.
She needs to cover it one minute (60 seconds). Therefore her speed must be:
186 m / 60 s = 3.1 m/s
Some metals have a molecular structure that makes them good conductors. Explain how understanding this relationship can help engineers make more powerful batteries.
Answers
Answer:
Explained below.
Explanation:
Conductors can be defined as materials that permit electricity to flow through them easily.
Now, metals have a molecular structure that makes them good conductors because electrons in the atoms of these conductors tend to move freely from one atom to the other. So a majority of metals make good conductors because these metals tend to hold their electrons loosely. In short, it can help engineers make powerful batteries because then it means that they are capable of giving much more electrical energy since nowadays, advanced batteries make use of ion charges for the batteries.
How fast should a rocket ship move for its mass to be dilated to 167% of its rest
mass?
Answers
Answer:
The two forces acting on rockets at the moment of launch are the thrust upwards and the weight downwards. Weight is the force due to gravity and is calculated (at the Earth’s surface) by multiplying the mass (kilograms) by 9.8.The resultant force on each rocket is calculated using the equation resultant force = thrust – weight.
Hopefully, this answer helps you! :)
Parent: My son spends three hours on homework every night. He has no time to see his friends. He has no time to relax. We are watching him turn into a homework machine instead of a human being.
Answers
Answer:
this is a homework helping website I don't know If I can help you with this problwm
a boy pushing a 200kg object on the floor it begins from rest and reaches 20 m/s² in 10 minutes, what is it's acceleration?
Answers
Answer:
I hope the above pic helps you mate
I will always help you understanding your assingments
have a great day
#Captainpower:)
A box of weighing 60N is placed on the ground. The bottom of the box measures 2m by 1m. What is the pressure on the ground? *
Answers
Answer:
pressure=force/area
p=60N/(2m×1m)
=35N/M
A circular wire loop lies inside a region of space containing a magnetic field. The direction of the magnetic field is out of the screen and parallel to the central axis of the loop. The magnitude of the magnetic field increases as a function of time. A circular loop oriented parallel to the plane of the screen lies inside a region containing magnetic field B. The field is directed out of the screen and is increasing. What is the direction of the induced current in the loop
Answers
Answer:
clockwise
Explanation:
According to the law given by Lenz, known as the Lenz law, it is said that a current induced in the circuit which is due to the change in the magnetic field and is so directed so as to oppose the change in the flux and to apply a force in the opposite direction if the force.
Here, as the magnetic field is directed out of the screen, the current flows in the direction which is clockwise in the loop and it opposes the increasing magnetic field.
The clockwise induced current will produce magnetic field in to the screen.
5. The wire in consists of two segments of different diameters but made from the same metal. The current in segment 1 is I1. a. (1 pt) Compare the currents in the two segments. That is, is I2 greater than, less than, or equal to I1? Explain. b. (1 pt) Compare the current densities J1 and J2 in the two segments. c. (1 pt) Compare the electric field strengths E1 and E2 in the two segments. d. (1 pt) Compare the drift speeds vd1 and vd2 in the two segments.
Answers
Answer:
hello your question is incomplete attached below is the complete question
answer :
a) I1 = I2
b) J1 > J2
c) E 1 > E2
d) ( vd1 ) > ( vd2 )
Explanation:
a) The currents in the two segments are the same i.e. I1 = I2 and this is because the segments are connected in series
b) Comparing the current densities J1 and J2 in the two segments
note : current density ∝ 1 / area
The area of the second segment is > the area of first segment therefore
J1 > J2
J1 ( current density of first segment )
J2 ( current density of second segment )
c) Comparing the electric field strengths E1 and E2
note : electric field strength ∝ current density
since current density of first segment is > current density of second segment and conductivity of the materials are the same hence
E 1 > E2
d) Comparing the drift speeds Vd1 and Vd2
( vd1 ) > ( vd2 )
this because ; vd ∝ current density
Currents in the two segments are equal. Current densities, electric field strengths and drift speeds of the first segment are greater than the second segment.
What is electric field?The electric field is the field, which is surrounded by the electric charged. The electric field is the electric force per unit charge.
The wire in consists of two segments of different diameters but made from the same metal.
a. Compare the currents in the two segments.The current in segment 1 is [tex]I_1[/tex] and the current in segment 2 is [tex]I_2[/tex]. As, the segments are connected in the series connection. Thus, the value of both the currents will be equal.
[tex]I=I_1=I_2[/tex]
b. Compare the current densities J1 and J2 in the two segments.The current density is total electric current which is flowing in a unit cross sectional area. Current density is inversely p[proportional to the cross sectional area.
The cross-sectional area of the second segment is greater than the first one as shown in the image attached below.
Thus, the current densities of first segment will be J1 greater than the current density of second segment J2.
[tex]J_1 > J_2[/tex]
c. Compare the electric field strengths E1 and E2 in the two segments.The current density of the first segment is greater than the second one. Thus, the electric field of the first segment will also be greater than the second one for the same material.
[tex]E_1 > E_2[/tex]
d. Compare the drift speeds vd1 and vd2 in the two segments.Current density is directly proportional to the drift velocity. As the current densities of first segment is greater than the current density of second segment.Therefore, there drift speed,
[tex]v_{d1} > v_{d2}[/tex]
Hence, the currents in the two segments are equal. Current densities, electric field strengths and drift speeds of the first segment are greater than the second segment.
Learn more about electric field here;
https://brainly.com/question/14372859
Which example provides a complete scientific description of an object in motion?
(A) The hiker followed the north trail a distance of two kilometers in thirty minutes
(B) The tiger had to run at 50 kilometers per hour across the field to catch the zebra
(C) The hockey player sent the puck flying toward the north goal to score the winning point
(D) The vibration of the jackhammer broke through the south-facing rock in under 10 seconds
Answers
Answer:
C
Explanation:
it explains how an object that was in motion continued motion after the force
A ball weighing 60 N is swinging like a pendulum at the end of a 6.0 m rope. As the ball swings through its lowest point, its speed is measured at 5.0 m/s. What is the tension in the rope at this point?
A. 58.6 N
B. 85.4 N
C. 90.2 N
D. 97.3 N
Answers
Answer:
85.4 N
Explanation:
Weight of the ball, W = 60 N
W = mg, m is mass
m = W/g
m = 60/9.8 = 6.12 kg
Length of a rope, r = 6 m
Speed, v = 5 m/s
We need to find the tension in the rope at this point. Tension is equal to the centripetal force It is given by :
[tex]F=\dfrac{mv^2}{r}+mg\\\\F=\dfrac{6.12\times (5)^2}{6}+60\\\\=85.5\ N[/tex]
So, the correct option is (b) " 85.4 N".
A race car starts from rest and accelerates down a track at a rate of 3.0 m/s2
How fast is the car moving after 10 seconds?
Answers
30 m/s
Explanation:We are given:
Initial Velocity (u) = 0 m/s
Acceleration of the Car (a) = 3 m/s²
Time Interval (t) = 10 seconds
Speed of the Car After 10 seconds:
From the First equation of motion:
v = u + at
replacing the given values
v = 0 + (3)(10)
v = 30 m/s
Hence, the car is moving at a velocity of 30 m/s after 10 seconds
What is the water cycle ?
Answers
Answer:
The water cycle shows the continuous movement of water within the Earth and atmosphere. ... Liquid water evaporates into water vapor, condenses to form clouds, and precipitates back to earth in the form of rain and snow. Water in different phases moves through the atmosphere (transportation).
Explanation:
It's the water cycle.
The phrase "ten meters per second squared" describes the
Answers
Answer:
Acceleration
Explanation;
change in velocity over timeTherefore metre per second over second, which is meter per second squaredWhat are the effects of hot rolling on the metal grain structure?
Answers
Answer:Mark me as the brainliset
Explanation:The rollers impart compression stresses, while squeezing the metal. These results in changes of grains, grain fragmentation, and lattice distortion. In hot rolling the coarse grains are converted into smaller grains. Care has been taken that the correct range of temperature is maintained during the process.
A chimpanzee climbs a vine up and to the right for a total displacement of 50 m 50m50, start text, m, end text that makes a 60 ° 60°60, degree angle from the ground. What was the horizontal displacement of the chimpanzee in m mstart text, m, end text?
Answers
Answer:
25m
Explanation
Let the horizontal displacement formula be expressed as;
Dx = Dcos theta
theta is the angles subtended by the displacement
Given
D = 50m
theta = 60°
Required
horizontal displacement of the chimpanzee
Substitute into the formula
Recall that: Dx = Dcos theta
Dx = 50cos60°
Dx = 50(0.5)
Dx = 25m
Hence the horizontal displacement of the chimpanzee is 25m
explain and derive the equation for capillary action in the phenomenon of surface tension
Answers
Answer:
Explanation:Capillary action is the ability of a liquid to flow in narrow spaces without the assistance of, ... This article is about the physical phenomenon. ... If the diameter of the tube is sufficiently small, then the combination of surface tension (which is caused by cohesion ... They derived the Young–Laplace equation of capillary action.
ASAP PLS HELP
What is chemical potential energy?
Answers
Answer:
chemical potential of a species is energy that can be absorbed or released due to a change of the particle number of the given species, e.g. in a chemical reaction or phase transition.
Explanation:
what are the importance of informal education?
Answers
Answer:
Informal education is important because it can help individual to learn how to react and control situations.
It help individual to improve on its existing knowledge, new skills or ideas. This kind of education can happen any where and it can add values to the learner.
Explanation:
Informal education is a type of education that is learned from different life experiences, happenings outside a structured curriculum.
Informal education is important because it can help individual to learn how to react and control situations.
It help individual to improve on its existing knowledge, new skills or ideas. This kind of education can happen any where and it can add values to the learner.
A pail in a water well is hoisted by means of a frictionless winch, which consists of a spool and a hand crank. When Jill turns the winch at her fastest water-fetching rate, she can lift the pail the 28.0 m to the top in 11.0 s. Calculate the average power supplied by Jill's muscles during the upward ascent. Assume the pail of water when full has a mass of 7.30 kg.
Answers
Answer:
182.28 W
Explanation:
Here ,
m = 7.30 Kg
distance , d= 28.0 m
time , t = 11.0 s
average power supplied = change in potential energy/time
average power supplied = m×g×d/time
average power supplied = 7.30×9.81×28/11
average power supplied = 182.28 W
the average power supplied is 182.28 W
Isaac Newton discovered the three laws of motion. Which example best illustrates Newton's third law of motion, which describes action and reaction forces?
O a rocket takes off from the ground
O a book slides forward on a seat when the car stops
O a heavier ball falls at the same speed as a lighter ball
O a vehicle rounds a curve and changes its acceleration
Answers
The third law of motion defined the action and reaction force that the heavy ball should be fall at the same kind of the speed.
What is third law of motion?It defined that at the time when the two bodies should be interacted so here the forces should be applied to one another that should be equivalent to the magnitude also the direction should be opposite.
Also, we can called as the action law and the reaction.
Therefore, we can conclude that the third option is correct.
Learn more about motion here: https://brainly.com/question/12742278
As an astronaunt travels from the surface of the earth to a postion that is four times
as far away from the center of the earth, the astronaut's
a) mass decreases
b)
mass remains the same
c) weight increases
d) weight remains the same
Answers
Answer: mass remains the same
Explanation:
My teacher gave me the answer
As an astronaut travels from the surface of the earth to a position that is four times as far away from the center of the earth, the astronaut's:
B. Mass remains the sameAccording to the given question, we can see that an astronaut is on a journey to a new location which is four times further from the center of the earth. We need to find out if there is a change to the mass of the astronaut.
As a result of this, we can see that the mass of the astronaut remains the same as he travels to a position which is four times further from the center of the earth, because the gravitational forces are the same.
Therefore, the correct answer is option B
Read more here:
https://brainly.com/question/17301500
Consider a star that is a sphere with a radius of 6.32 108 m and an average surface temperature of 5350 K. Determine the amount by which the star's thermal radiation increases the entropy of the entire universe each second. Assume that the star is a perfect blackbody, and that the average temperature of the rest of the universe is 2.73 K. Do not consider the thermal radiation absorbed by the star from the rest of the universe. J/K
Answers
Answer:
The value is [tex]\Delta s = 8.537 *10^{25 } \ J/K[/tex]
Explanation:
From the we are told that
The radius of the sphere is [tex]r = 6.32 *10^{8} \ m[/tex]
The temperature is [tex]T_x = 5350 \ K[/tex]
The average temperature of the rest of the universe is [tex]T_r = 2.73 \ K[/tex]
Generally the change in entropy of the entire universe per second is mathematically represented as
[tex]\Delta s = s_r - s_x[/tex]
Here [tex]s_r[/tex] is the entropy of the rest of the universe which is mathematically represented as
[tex]s_r = \frac{Q}{T_r}[/tex]
Here Q is the quantity of heat radiated by the star which is mathematically represented as
[tex]Q = 4 \pi * r^2 * \sigma * T^4_x[/tex]
Here [tex]\sigma[/tex] is the Stefan-Boltzmann constant with value
[tex]\sigma = 5.67 * 10^{-8 }W\cdot m^{-2} \cdot K^{-4}.[/tex]
=> [tex]Q = 4 \pi * (6.32*10^{8})^2 * 5.67 * 10^{-8 } * 5350 ^4[/tex]
=> [tex]Q = 2.332 *10^{26} \ J[/tex]
So
[tex]s_r = \frac{2.332 *10^{26}}{2.73}[/tex]
=> [tex]s_r = 8.5415 *10^{25}\ J/K[/tex]
Here [tex]s_x[/tex] is the entropy of the rest of the universe which is mathematically represented as
[tex]s_x = \frac{Q}{T_x}[/tex]
=> [tex]s_x = \frac{2.332 *10^{26} }{5350}[/tex]
=> [tex]s_x = 4.359 *10^{22} \ J/K[/tex]
So
[tex]\Delta s = 8.5415 *10^{25} - 4.359 *10^{22}[/tex]
=> [tex]\Delta s = 8.537 *10^{25 } \ J/K[/tex]
This question involves the concepts of entropy and the thermal radiation
The entropy of the entire universe is increased by "8.41 x 10²⁵ J/k
".
The increase in entropy is given as follows:
[tex]\Delta s = s-s_T[/tex]
where,
Δs = increase in entropy = ?
σ = Stefan-Boltzman's constant = 5.67 x 10⁻⁸ W/m².k⁴
A = surface area = 4πr² = 4π(6.32 x 10⁸ m)² = 5.01 x 10¹⁸ m²
Tr = Absolute temperature of the star = 5350 K
T = absolute temperature of the rest of the universe = 2.73 k
Q = thermal radiation energy
Q = [tex]\sigma A T_r^4=(5.67\ x\ ^{-8}\ W/m^2.k^4)(5.01\ x\ ^{18}\ m^2)(5350\ k)^4=2.3\ x\ 10^{26}\ J[/tex]
s = entropy of the universe = [tex]\frac{Q}{T}=\frac{2.3\ x\ 10^{26}\ J}{2.73 k}=8.42\ x\ 10^{25}\ J/k[/tex]
[tex]s_T[/tex] = entropy of the star = [tex]\frac{Q}{T_r}=\frac{2.3\ x\ 10^{26}\ J}{5350\ k}=4.3\ x\ 10^{22}\ J/k[/tex]
Therefore,
Δs = 8.42 x 10²⁵ J/k - 4.3 x 10²² J/k
Δs = 8.41 x 10²⁵ J/k
Learn more about entropy here:
https://brainly.com/question/13146879?referrer=searchResults
Two locomotives approach each other on parallel track. Each has speed of 95 km/h with respect to the ground.If they are initially 8.5 km apart. How long will it take before they reach each other?
Answers
Answer:
It will take 2.68 minutes for them to reach each other.
Explanation:
We use the two following kinematic equations, making the final position the same (for the moment they meet each other):
locomotive 1 --> [tex]x_f=v*t[/tex]
locomotive 2 --> [tex]x_f=8.5\,-\,v*t[/tex]
we make the two xf equal, and solve for the time (t) using v = 95 km/h:
[tex]95*t=8.5-95*t\\2*95*t=8.5\\t=8.5/(190)\\t = 0.0447\,\,hours[/tex]
converting the hours into minutes by multiplying this value times 60;
t = 2.68 minutes
A 200 g air-track glider is attached to a spring. The glider is pushed 10.0 cm against the spring, then released. A student with a stopwatch finds that 10 oscillating take 12.0 s. What is the spring constant?
Answers
Answer:
5.5N/m
Explanation:
Calculation for What is the spring constant
First step is to calculate the time period
T = 12 second/10
T = 1.2 second
Now let calculate the spring constant using this formula
k=4π²m/T²
Where,
m=0.2kg
T=1.2second
k represent spring constant=?
Let plug in the formula
k=4π²×0.2kg/(1.2)²
k=39.48×0.2kg/1.44
k=7.90/1.44
k=5.48N/m
k=5.5N/m ( Approximately)
Therefore the spring constant will be 5.5N/m
ANSWER ALL QUESTIONS and show your work ON THE ATTACHMENT AWARD 50 pts if you don’t know the answer to all of them I have posted them individually so I can still mark you brainlessly (however you spell the darn thing)
Answers
Answer:
the velocity is 210 - hq squared which equals to 14