Tungsten is being used at half its melting point (Tm≈3,400◦C) and astress level of 160 MPa. An engineer suggests increasing the grain size by afactor of 4 as an effective means of reducing the creep rate.(a)Do you agree with the engineer? Why? What if the stress level were equalto 1.6 MPa?(b)What is the predicted increase in length of the specimen after 10,000hours if the initial length is 10 cm?
Answers
Answer:
Explanation:
The missing diagram is attached in the image below which shows the deformation map of the Tungsten.
Given that:
Stress level [tex]\sigma = 160 MPa[/tex]
T = 0.5 Tm
[tex]\implies \dfrac{T}{Tm} = 0.5[/tex]
G = 160 GPa
[tex]\implies \dfrac{\sigma}{G} = 10^{-3}[/tex]
a)
The regulating creep mechanism is dislocation driven, as we can see from the deformation mechanism.
The engineer's recommendation would not be approved because increasing grain size results in a decrease in the grain-boundary count, preferring dislocation motion. The existence of grain borders is a hindrance to dislocation motion, as the dislocation principle explicitly states. To stop the motion, we'll need a substance with finer grains, which would result in more grain borders, or a material with higher pressure. In the case of Nabarro creep, which is diffusion-driven, an engineer's recommendation would be useful.
b)
If stress level reduced to [tex]\sigma = 1.6 MPa[/tex]
[tex]\implies \dfrac{\sigma }{G} = 10^{-5}[/tex]
Cable creep is now the controlling creep mode, which entails tension-driven atom diffusion along grain borders to elongate grain along the stress axis, a process known as grain-boundary diffusion. Cable creep is more common in fine-grained materials. As a result, the engineer's advice would succeed in this case. The affinity for cable creep is reduced when the grain size is increased.
c)
From the map of creep mechanism for [tex]\dfrac{\sigma}{G} = 10^{-3} \ and \ \dfrac{T}{Tm} = 0.5[/tex]
We read strain rate [tex](e) = 10^{-6}/sec[/tex]
Therefore,
[tex]Strain (E) = e * \Delta t[/tex]
[tex]= 10^{-6} \times 10000 \times 3600[/tex]
= 36
Therefore, [tex]\Delta L = E \times Li[/tex]
= [tex]36 * 10 cm[/tex]
= 360 cm
Thus, the increase in length = 360 cm
Related Questions
use clingo to find all solutions to the 8 queens problem that have no queens in the 4x4=16 squares in the middle of the board
Answers
To use Clingo to find all solutions to the 8 queens problem that have no queens in the 4x4=16 squares in the middle of the board, Define the rules First, Add the constraint Next, run Clingo to find all solutions that meet the defined rules and constraints.
To find all solutions to the 8 queens problem using clingo while excluding the 4x4 middle squares of the board, you can define the problem using the following clingo program:
% Define the board size
#const N = 8.
% Define the positions of the middle squares
middle(2,2). middle(2,3). middle(3,2). middle(3,3).
middle(6,6). middle(6,7). middle(7,6). middle(7,7).
% Define the column and row constraints
1 { queen(Col, Row) : Col=1..N } 1 :- Row=1..N.
:- queen(Col1, Row1), queen(Col2, Row2), Col1 != Col2, Row1 = Row2. % No two queens in the same row
:- queen(Col1, Row1), queen(Col2, Row2), Col1 = Col2, Row1 != Row2. % No two queens in the same column
% Define the diagonal constraints
:- queen(Col1, Row1), queen(Col2, Row2), Col1 - Row1 = Col2 - Row2. % No two queens in the same upward diagonal
:- queen(Col1, Row1), queen(Col2, Row2), Col1 + Row1 = Col2 + Row2. % No two queens in the same downward diagonal
% Exclude the middle squares
:- queen(Col, Row), middle(Col, Row).
% Find all solutions
#show queen/2.
Save the above code in a file named queens.lp and then execute clingo on the command line with the following command:
clingo queens.lp
Clingo will output all the solutions to the 8 queens problem that have no queens in the 4x4 middle squares of the board.
To learn more about 8 queens problem:
brainly.com/question/16987854
#SPJ4
You are performing a machining operation that approximates orthogonal cutting. Given that the chip thickness prior to chip formation is 0.5 inches and the chip thickness after separation is 1.125 inches, calculate the shear plane angle and shear strain. Use a rake angle of 10 degrees. 21. Suppose in the prior problem that the cutting force and thrust force were measured as 1559 N and 1271 N, respectively. The width of the cut is 3.0mm. Using this new information, calculate the shear strength of the material.
Answers
Answer:
A)
shear plane angle = 31.98°
shear strain = cot ( 31.98° ) + tan ( 31.98 - 10 )
B) shear strength = 7339.78
Explanation:
a) Determine the shear plane angle and shear strain
Given data :
Chip thickness before chip formation = 0.5 inches
Chip thickness after separation = 1.125 inches
rake angle ( ∝ ) = 10°
shear plane angle : Tan ∅ = [tex]\frac{rcos\alpha }{1-sin\alpha }[/tex] ----- ( 1 )
r = chip thickness ratio = 0.5 / 1.125 = 0.4444
back to equation 1 : Tan ∅ = ( 0.444 ) * cos 10 / 1 - sin 10
Tan ∅ = 0.4444 * 0.9848 / 1 - 0.1736 = 0.5296
hence ∅ = tan^-1 ( 0.5296 ) = 31.98°
shear strain : R = cot ∅ + tan ( ∅ - ∝ ) ---------- ( 1 )
R = cot ( 31.98° ) + tan ( 31.98 - 10 )
B) determine the shear strength of the material
cutting force = 1559 N
thrust force = 1271 N
width of cut ( diameter ) = 3.0 mm
shear strength = c + σ.tan ∅
c = cohesion force = 1271 * 3 = 3813
σ = normal stress = F / A = 1559 / π/4 * ( 0.5 )^2 = 1559 / 0.1963 = 7941.94
hence : shear strength of material = 3813 + 7941.94 * 0.6244 = 7339.78
T/F : The voltage through a resistor with current i(t) in the s-domain is sri(s).
Answers
False.
The voltage through a resistor with current i(t) in the s-domain is simply Ri(s), where R is the resistance value of the resistor. In the s-domain, the relationship between voltage and current through a resistor can be expressed using Ohm's law as V(s) = I(s)R.
Therefore, the voltage across a resistor in the s-domain is proportional to the current through it, with the proportionality constant being the resistance value. It's important to note that this relationship only holds true for resistive elements in linear circuits. Non-linear circuit elements such as diodes and transistors have much more complex voltage-current relationships that cannot be described using a simple linear equation.
To know more about diodes visit:
https://brainly.com/question/32612539
#SPJ11
INTERACTIVE SESSION MANAGEMENT Big Data Baseball Big data and analytics are sweeping the business base running, and stealing. Skill in fielding is espe- world, and the professional sports industry is no cially valued today. For example, Mike Trout, center exception. Baseball, football, soccer, hockey, ten- fielder for the Los Angeles Angels, is highly regarded nis, and even sailboat racing are finding ways to by team owners because he's an exceptional fielder analyze data about players and competing teams in and base runner and an exceptionally intelligent order to improve performance. The use of analytics base ball player, even though he lacked stellar sta- and big data has revolutionized the game of base- tistics in home runs. Today the biggest challenge is ball as we know it, including defensive shifts, swing not whether to use big data in baseball but how to path changes, and how teams acquire and develop use it effectively. It is not always possible to inter- players pret the data and separate out what is "noise" and Given the huge disparities in Major League what is actually actionable information. The amount Baseball (MLB) team budgets, wealthier teams typi- of data players and pitchers must deal with can be cally have the advantage in recruiting the best play- overwhelming-pitch usage, swing planes, spin rates, ers. Michael Lewis's book Moneyball, published in etc. When a player steps into the batter's box, every 2003, describes how Oakland Athletics manager Billy hitter is different in terms of how much information Beane was able to turn the underdog A's into a win- that person can absorb before getting bogged down in ning team by using big data analytics to guide deci- it. Some want to know what a pitcher will do in cer- sions about which players to recruit and cultivate. tain situations-what pitches the pitcher will use and Rigorous statistical analysis had demonstrated that how often that person uses them-while some want on-base percentage and slugging percentage were to just step in with a clear head and look for the ball. better indicators of offensive success and cheaper There's only so much data a person can use without to obtain on the open market) than more historically dissecting too much and getting too distracted from valued qualities such as speed and contact. These the task at hand. observations flew in the face of conventional base Many baseball experts still believe that tradi- ball wisdom and the beliefs of many baseball talent tional methods of player evaluation, along with gut scouts and coaches. Beane rebuilt the A's based on instinct, money, and luck, are still key ingredients these findings, producing a consistently winning for winning teams. For example, the San Francisco team for a number of years by using advanced ana- Giants use big data and statistics, but also base their lytics to gain insights into each player's value and player recruitment decisions on the opinions of contribution to team success that wealthier teams scouts and coaches. According to Giants bench coach had overlooked Ron Worus, numbers really can't tell the whole story Big data is credited with helping the Boston Red about the quality of the player; so the Giants inte- Sox win the World Series in 2004 and the St. Louis grate statistical data with scouting, coaching, and Cardinals win in 2006 and 2011. To varying degrees, player experience, especially when dealing with op- every Major League Baseball team today uses big ponents outside the National League that the Giants data and deep analytics to support decisions about do not see regularly. Being able to exploit an indi- many aspects of the game. However, some teams, vidual player's strengths comes more from knowing such as the Pittsburgh Pirates, Chicago Cubs, and the player and his ability as opposed to the statistics, Houston Astros, were slower to do so than others, Wotus believes. Shortstops with good arms can play and suffered lackluster performance until they em- farther from home plate than normal at times, while braced big data more fully fast runners can play closer to home plate than Findings from big data analytics have changed the usual. There are nuances to defending the opposition importance baseball teams attach to specific skills of that are not statistically related, but statistics help players Skills that previously could not be quantified when you don't know players well enough to know are now receiving more attention, including fielding what to expect from them. CASE STUDY QUESTIONS 1. How did information technology change the game 3. How much should baseball rely on big data and of baseball? Explain. analytics? Explain your answer. 2. How did information technology affect decision making at MLB teams? What kinds of decisions changed as the result of using big data?
Answers
1. **Information technology revolutionized the game of baseball** by introducing big data and analytics. These advancements allowed teams to gather and analyze vast amounts of data about players and competing teams, enabling them to improve performance in various areas such as base running, fielding, and player recruitment. The use of analytics transformed strategies and tactics, leading to defensive shifts, swing path changes, and more informed decision-making processes. Michael Lewis's book "Moneyball" highlighted how the Oakland Athletics used big data analytics to turn their team into a winning force by focusing on statistical indicators of success, challenging conventional baseball wisdom.
2. The use of information technology, particularly big data, **altered decision-making processes in MLB teams**. The availability of extensive data and advanced analytics enabled teams to make more informed decisions regarding player recruitment, player development, game strategies, and overall team management. Traditional evaluation methods, based on gut instincts and subjective opinions, started to give way to objective data-driven approaches. Teams began using statistical analysis to identify undervalued players, understand player value and contribution to team success, and optimize game plans based on opponents' strengths and weaknesses.
Learn more about decision-making processes here:
https://brainly.com/question/29772020
#SPJ11
reduce 5cos(ωt 75∘)−3cos(ωt−75∘) 4sin(ωt) to the form vmcos(ωt θ) .
Answers
The reduced form of the expression is vmcos(ωt + θ), where vm = 2 and θ = 75°.
To reduce the expression 5cos(ωt + 75°) - 3cos(ωt - 75°) + 4sin(ωt) to the form vmcos(ωt + θ), we can use trigonometric identities to simplify and rearrange the terms.
Starting with the given expression:
5cos(ωt + 75°) - 3cos(ωt - 75°) + 4sin(ωt)
We can rewrite cos(ωt - 75°) using the identity cos(-θ) = cos(θ):
5cos(ωt + 75°) - 3cos(75° - ωt) + 4sin(ωt)
Next, using the identity cos(A + B) = cos(A)cos(B) - sin(A)sin(B), we can expand the first term:
5[cos(ωt)cos(75°) - sin(ωt)sin(75°)] - 3cos(75° - ωt) + 4sin(ωt)
Simplifying further:
5[cos(ωt)cos(75°) - sin(ωt)sin(75°)] - 3[cos(75°)cos(ωt) + sin(75°)sin(ωt)] + 4sin(ωt)
Using the identity cos(θ) = cos(-θ) and sin(θ) = -sin(-θ), we can rewrite some terms:
5[cos(ωt)cos(75°) - sin(ωt)sin(75°)] - 3[cos(75°)cos(ωt) - sin(75°)sin(ωt)] + 4sin(ωt)
Simplifying further:
5cos(ωt)cos(75°) - 5sin(ωt)sin(75°) - 3cos(75°)cos(ωt) + 3sin(75°)sin(ωt) + 4sin(ωt)
Now, using the identities cos(A)cos(B) = 0.5[cos(A - B) + cos(A + B)] and sin(A)sin(B) = 0.5[cos(A - B) - cos(A + B)], we can simplify the expression:
[5cos(ωt)cos(75°) - 3cos(75°)cos(ωt)] + [3sin(75°)sin(ωt) + 4sin(ωt)]
Using the identity cos(θ) = cos(-θ) and sin(θ) = -sin(-θ) again, we can simplify further:
[5cos(ωt)cos(75°) - 3cos(ωt)cos(75°)] + [3sin(75°)sin(ωt) - 4sin(ωt)]
Simplifying the terms:
2cos(ωt)cos(75°) - sin(ωt)[4 - 3sin(75°)]
Finally, we can rewrite the expression in the desired form:
vmcos(ωt + θ) = 2cos(ωt)cos(75°) - sin(ωt)[4 - 3sin(75°)]
Therefore, the reduced form of the expression is vmcos(ωt + θ), where vm = 2 and θ = 75°.
Learn more about reduced form here:-
https://brainly.com/question/24232068
#SPJ11
A distance of 118.060 m was measured along a 2-percent slope. Compute the horizontal distance.
Answers
The horizontal distance along the 2-percent slope is approximately 115.61 meters.
In order to compute the horizontal distance, we need to take into account the measured distance along the slope and the percent slope. The given problem states that a distance of 118.060 meters was measured along a 2-percent slope.
To find the horizontal distance, we use the formula: Horizontal distance = Measured distance / (1 + (Percent slope/100)).
Substituting the values into the formula, we have: Horizontal distance = 118.060 / (1 + (2/100)).
To simplify the expression inside the parentheses, we convert the percent slope to a decimal by dividing it by 100. Thus, (2/100) becomes 0.02.
Continuing the calculation, we have: Horizontal distance = 118.060 / (1 + 0.02).
Simplifying further, we add 1 and 0.02 to get 1.02 in the denominator.
Finally, we divide 118.060 by 1.02 to find the horizontal distance, which is approximately equal to 115.61 meters.
Therefore, the horizontal distance along the 2-percent slope is approximately 115.61 meters.
Learn more about horizontal distance here :-
https://brainly.com/question/10093142
#SPJ11
One difference between NoSQL and relational databases is that... a. NoSQL databases require large powerful, and expensive proprietary a servers b. relational databases consistently provide fasterresponse times for queries. c. NoSQL databases have a greater horizontal scaling capability. d. relational databases can easily spread data over multiple servers
Answers
To determine the angular momentum and its rate of change, we need more information, specifically the position vector and velocity vector of the particle, as well as the force vector acting on it.
Please provide the relevant information or a description of the figure so that I can assist you further.
Angular momentum (L) is defined as the cross product of the position vector (r) and the linear momentum vector (p):
L = r x p
The time rate of change of angular momentum (dL/dt) is equal to the torque (τ) applied to the particle:
dL/dt = τ
If the force acting on the particle is known, the torque can be calculated using the equation:
τ = r x F
Once we have the torque, we can determine the angular momentum and its rate of change. Please provide the necessary information so that I can help you with the calculations.
Learn more about momentum here
https://brainly.com/question/30319928
#SPJ11
consider a stead flow ideal carnot cycle using steam as the working fluid in which the high temperature constant pressure heat addition process starts with a saturated liquid and ends with a saturated vapor. plot this cycle in t-s coordinates showing the steam dome. calculate the thermal efficiency for this cycle if the pressure of the high temperature steam is 6 mpa and the low temperature heat rejection process occurs at 300 k.
Answers
Answer:
45.32%
Explanation:
Given data:
pressure of high temperature steam = 6 MPa
low temperature heat rejection process ( Tr ) = 300 k
A) plot of cycle in t-s coordinates showing steam dome
attached below
B) Calculate thermal efficiency
thermal efficiency = 1 - (Tr / Tsat )
Tsat = 275.59°C ≈ 548.59 K ( from steam table at Pa = 6 MPa )
back to equation 1
1 - (300 / 548.59 )
1 - 0.5468 = 0.4532 = 45.32%
Consider a ramjet engine at an altitude where temperature is 223 K. The flight Mach number is M = 4. At the entrance to the burner, the Mach number is 0.3. Combustion in the burner (whose cross-sectional area is constant) may be represented approximately as heating of a perfect gas with constant specific heat ratio. At the exit from the burner the temperature of the gas is 2462 K. Neglecting frictional effects in the burner and considering the flow to be one-dimensional throughout, estimate the Mach number of the gas leaving the burner. Determine also the stagnation pressure loss due to heating (i.e. calculate the ratio of outlet and inlet stagnation pressures).
Answers
The required answer is:Mach number of the gas leaving the burner, M2 = 2.32Stagnation pressure loss due to heating = 54.8% or 0.548 or 1.84/3.35.
Given data:Mach number at the entrance of the burner, M1 = 0.3Temperature at the entrance of the burner, T1 = 223 KTemperature at the exit of the burner, T2 = 2462 KFlight Mach number, M = 4We have to determine the Mach number of the gas leaving the burner and the stagnation pressure loss due to heating.Mach number at exit, M2 can be determined using the isentropic relation as below:where γ is the ratio of specific heats. This is because the flow is isentropic through the nozzle.Stagnation pressure at the entrance of the burner, P01 = stagnation pressure at the exit of the burner, P02Therefore,Stagnation pressure loss due to heating,This can be determined using the relation for isentropic flow as below:Thus, the Mach number of the gas leaving the burner is 2.32 and the stagnation pressure loss due to heating is 0.548 or 54.8%.Hence, the required answer is:Mach number of the gas leaving the burner, M2 = 2.32Stagnation pressure loss due to heating = 54.8% or 0.548 or 1.84/3.35.
Learn more about Stagnation pressure here,
https://brainly.com/question/31391195
#SPJ11
Discuss in detail the manners of interaction with opposite gender
Answers
Answer:
8 Tips on Better Communication with the Opposite Sex
Put emotions away. Ladies, this one is more aimed at us, for the most part. ...
Forget your pride. In discussions, especially these days, people always want to be the one that prevails. .
Put yourself in their shoes. .
Listen. ...
Respond. ...
Actually communicate. ...
Be detailed. ...
Don't communicate too much.
Explanation:
Show that if a square matrix A satisfies he equation A2 +2A + I = 0, then A must be invertible. what is the inverse?
Answers
Answer: A is invertible and the inverse is given by A⁻¹ = -1/ (A + 2I).
Explanation: Given that the matrix A satisfies the equation A² + 2A + I = 0.
To show that A is invertible, we must show that det(A) ≠ 0 since the determinant of a matrix is 0 if and only if the matrix is not invertible.A² + 2A + I = 0⇒ A² + 2A = -I⇒ A(A + 2I) = -I⇒ A = -1/ (A + 2I)Since the inverse of a matrix is unique if it exists, the above formula shows that A⁻¹ exists.
Therefore, A is invertible and the inverse is given by A⁻¹ = -1/ (A + 2I).
Learn more about square matrix here https://brainly.in/question/55204637
#SPJ11
In an allocator using an implicit free list, the header contains an allocated bit and a pointer to the next block the size of the current block the size of the next block
Answers
In an allocator that utilizes an implicit free list, each block typically contains a header that stores information about the block's state and size. The header's structure may differ depending on the specific allocator implementation, but it generally includes an allocated bit and the block's size.
The allocated bit serves as a flag indicating whether the block is currently allocated or free. It enables the allocator to differentiate between blocks in use by the program and blocks available for allocation. Typically, the allocated bit is represented by a single binary digit, where 1 denotes an allocated block and 0 signifies a free block.Moreover, the header may also include the size of the current block and, in some cases, the size of the next block. These size values aid the allocator in efficiently traversing the implicit free list. The size of the current block enables the allocator to determine the block's boundaries and calculate the memory location of the subsequent block. By knowing the size of the next block, the allocator can easily identify the starting point of that block when iterating through the free list.
It is worth noting that the specific layout of the header can vary depending on the allocator's implementation and any additional metadata required. Different memory allocators may employ distinct approaches, leading to variations in implementation details. This response provides a general overview of the key concepts typically associated with an allocator utilizing an implicit free list.
To learn more about memory visit: https://brainly.com/question/28483224
#SPJ11
A cylindrical metal specimen having an original diameter of 10.33 mm and gauge length of 52.8 mm is pulled in tension until fracture occurs. The diameter at the point of fracture is 6.38 mm, and the fractured gauge length is 73.9 mm. Calculate the ductility in terms of (a) percent reduction in area (percent RA), and (b) percent elongation (percent EL).
Answers
Answer
a) 62 percent
b) 40 percent
Explanation:
Original diameter ( d[tex]_{i}[/tex] ) = 10.33 mm
Original Gauge length ( L[tex]_{i}[/tex] ) = 52.8 mm
diameter at point of fracture ( d[tex]_{f}[/tex] ) = 6.38 mm
New gauge length ( L[tex]_{f}[/tex] ) = 73.9 mm
Calculate ductility in terms of
a) percent reduction in area
percentage reduction = [ (A[tex]_{i}[/tex] - A[tex]_{f}[/tex] ) / A[tex]_{i}[/tex] ] * 100
A[tex]_{i}[/tex] ( initial area ) = π /4 di^2
= π /4 * ( 10.33 )^2 = 83.81 mm^2
A[tex]_{f}[/tex] ( final area ) = π /4 df^2
= π /4 ( 6.38)^2 = 31.97 mm^2
hence : %reduction = ( 83.81 - 31.97 ) / 83.81
= 0.62 = 62 percent
b ) percent elongation
percentage elongation = ( L[tex]_{f}[/tex] - L[tex]_{i}[/tex] ) / L[tex]_{i}[/tex]
= ( 73.9 - 52.8 ) / 52.8 = 0.40 = 40 percent
.Helium gas is compressed from 27 C and 3.50 m^3/kg to 0.775 m3/kg in a reversible and adiabatic manner. The temperature of helium alter compression is ___. a) 547 C b) 709 C c) 74 C d) 1082 C e) 122 C
Answers
Answer: i think the answer is A
Explanation:
have a nice day and let me know if i was wrong please
The temperature of helium after compression is approximately 16°C.Option (e) 122°C is incorrect.
Given data:
Initial temperature, T₁ = 27°C
Compressed volume, V₂ = 0.775 m³/kg
Initial volume, V₁ = 3.50 m³/kg
We know that PVγ = constant
For reversible adiabatic process,γ = CP / CV = 5/3 (for monoatomic gas)
Let's use the relation PVγ = constant to find the final temperature after compression and rearrange the formula as:
P₁V₁γ = P₂V₂γ
where P₁ = pressure at initial state = P₂ (pressure is constant as the compression is reversible adiabatic)
T₂ = ?
Now substitute the given values in the above equation, as follows:
P₁V₁γ = P₂V₂γ
⇒ V₁γ / V₂γ = 1T₂ = T₁(V₂ / V₁)^(γ - 1)
Put all the values in the above equation to get the final answer.
T₂ = 27°C(0.775 m³/kg / 3.50 m³/kg)^(5/3 - 1)
T₂ = 27°C(0.221)^(2/3)
T₂ = 27°C x 0.574
T₂ = 15.52 °C ≈ 16 °C
Therefore, the temperature of helium after compression is approximately 16°C.Option (e) 122°C is incorrect.
Learn more about reversible adiabatic process here:
https://brainly.com/question/29333973
#SPJ11
By using some sorting technique an array of 8 elements was sorted and the sorting algorithm found the larger number first .The elements of an array in order 2 4 5 7 8 1 3 6 after 4 iteration.
Answers
The sorting algorithm found the larger number first in the array, resulting in the order 8 7 6 5 4 3 2 1 after 4 iterations.
The given array had 8 elements: 2, 4, 5, 7, 8, 1, 3, 6. During the sorting process, the algorithm compares adjacent elements and swaps them if they are in the wrong order. In this case, the algorithm prioritized finding the larger numbers first. After four iterations, the largest number (8) moved to the first position, followed by 7, 6, 5, and so on, resulting in the sorted order of 8, 7, 6, 5, 4, 3, 2, 1. It's important to note that the specific sorting algorithm used and its implementation details could affect the exact number of iterations required and the resulting order.
Learn more about algorithm here :-
https://brainly.com/question/21172316
#SPJ11
From the Smith chart, find the normalized input admittances corresponding to the following normalized input impedances (a) Z=07-jo.3 (b) z= 4+j3
(c)Z= j[infinity]
Answers
The normalized input admittances corresponding to the following normalized input impedances are
(a) For Z = 0.7 - j0.3, the normalized input admittance is Y = 0.7 - j0.3., (b) For Z = 4 + j3, the normalized input admittance is Y = 4 - j3.,(c) For Z = j[infinity], the normalized input admittance is Y = 0.
To find the normalized input admittances corresponding to the given normalized input impedances using the Smith chart, we need to plot the impedance points on the Smith chart and then read the admittance values at those points. However, as a text-based AI model, I am unable to provide visual representations or plot points on a Smith chart directly.
Nonetheless, I can explain the procedure and provide you with the equations to calculate the normalized input admittances corresponding to the given normalized input impedances. The Smith chart is a graphical tool that simplifies the calculations, but we can still determine the values mathematically.
(a) For Z = 0.7 - j0.3:
To find the corresponding normalized input admittance, we take the complex conjugate of the impedance:
Y = (0.7 + j0.3)*
Therefore, the normalized input admittance is Y = 0.7 - j0.3.
(b) For Z = 4 + j3:
Again, we take the complex conjugate of the impedance to find the normalized input admittance:
Y = (4 + j3)*
Therefore, the normalized input admittance is Y = 4 - j3.
(c) For Z = j[infinity]:
In this case, the impedance represents an open circuit, which corresponds to infinite impedance. For an open circuit, the normalized input admittance is zero.
Therefore, the normalized input admittance is Y = 0.
To learn more about impedance visit: https://brainly.com/question/31369031
#SPJ11
List six possible valve defects that should be included in the inspection of a used valve?
Answers
Answer:
Valvular stenosis , Valvular prolapse , Regurgitation,
Explanation:
Which of the following metals are widely used as the matrix metals in tungsten carbide and titanium carbide cermets? (a) aluminum (b) chromium (c) cobalt (d) lead (e) nickel (f) vanadium
Answers
Cobalt is one of the matrix metals widely used in tungsten carbide and titanium carbide cermets.
Tungsten carbide is a hard material that is used in manufacturing cutting tools, milling and turning inserts, and wear-resistant parts. Cobalt metal is utilized as a matrix metal because of its exceptional bonding characteristics and temperature stability. Titanium carbide (TiC) is another hard material utilized as an abrasive. It is a grey powder that is insoluble in water. Cobalt is also utilized in titanium carbide as a matrix metal because of its capacity to form hard, stable carbides. Cobalt improves the hardness and strength of the carbide ceramic's microstructure and improves its mechanical properties. Cobalt is used as a matrix metal in tungsten carbide and titanium carbide cermets. The metal that is widely used as the matrix metal in tungsten carbide and titanium carbide cermets is cobalt.
know more about Tungsten carbide
https://brainly.com/question/31963394
#SPJ11
which of the following is not a high-level programming language? select all that apply.
O javaP
O Phyton
O Assembly
O C++
O Machine
O Perl
O Ruby
Answers
The required correct answer is: Machine
Explanation : Machine is not a high-level programming language. Machine language is a low-level programming language that is directly understood and executed by the computer's central processing unit (CPU). This language is specific to the type of computer's CPU architecture, such as Intel, ARM, etc. It is machine-dependent, so it is not portable, and it is challenging to program directly. It is composed of binary digits (0 and 1), and programmers use a sequence of machine instructions to create programs that can interact directly with the hardware to perform low-level tasks.Other options like Java, Python, Assembly, C++, Perl, and Ruby are high-level programming languages. They are human-readable, have syntax rules, and allow for easier and more abstract programming. Programmers can use high-level programming languages to create complex applications quickly and efficiently, unlike low-level programming languages.
Learn more about high-level programming languages here https://brainly.in/question/20657262
#SPJ11
Ethernet (10Mbps) frames must be at least 64 bytes (512 bits) long to ensure that the transmitter is still going in the event of a collision at the far end of the cable. Fast Ethernet (100Mbps) has the same 64-byte minimum frame size but can get the bits out ten times faster. How is it possible to maintain the same minimum frame size?
Answers
Fast Ethernet has also maintained the same minimum frame size of 64 bytes to ensure uninterrupted data transmission even after a collision.
The main reason for having a minimum frame size of 64 bytes is to make sure that the data transmission is complete even after the collision. If two signals get collided in the Ethernet, the signal from both will become ineffective. In such a case, the frame should be long enough to continue transmitting data, so that the signal can travel all the way to the end of the cable without any interference. The above concept is followed in the case of Ethernet (10Mbps). The signal transmission speed of Ethernet is 10Mbps. So, if there is a collision, the signal should be long enough to continue transmitting data, so that the signal can travel all the way to the end of the cable without any interference.
Therefore, the minimum frame size of Ethernet is 64 bytes. If there is a collision at the far end of the cable, the signal is still going. Fast Ethernet (100Mbps) has the same 64-byte minimum frame size but can get the bits out ten times faster. The reason behind maintaining the same minimum frame size is the same as that of Ethernet. When a collision occurs, the signal transmission should be long enough to continue transmitting data, so that the signal can travel all the way to the end of the cable without any interference.
Therefore, Fast Ethernet has also maintained the same minimum frame size of 64 bytes to ensure uninterrupted data transmission even after a collision.
know more about Fast Ethernet
https://brainly.com/question/32106050
#SPJ11
PuHyPriCo
- Public Cloud
- Hybrid Cloud
- Private Cloud
- Community Cloud
A. Installation and Usage Models
B Delivery Models
C. Deployment Models
D. On-demand usage
E. Cloud Provider
Answers
From the given options (C) Deployment Models notion is NOT a deployment model for cloud computing.
An alternative to a hybrid cloud that limits the addition and removal of cloud services over time is a composite cloud.
Users in a network can access resources using cloud compounding that is located elsewhere on the internet and not on the user's machine (Gartner, 2012).
The Compound Cloud concept is NOT a cloud computing deployment model.
In order to provide quicker innovation, adaptable resources, and scale economies, cloud computing, in its simplest form, is the supply of computing services via the Internet ("the cloud"), encompassing servers, storage, databases, networking, software, analytics, and intelligence.
Therefore, from the given options (C) Deployment Models notion is NOT a deployment model for cloud computing.
Know more about Cloud Computing here:
brainly.com/question/19057393
#SPJ1
What would be introduced as criteria of a table being in second normal form?
a.) There should be no functional dependencies.
b.) Every functional dependency where X is functionally dependent on Y, X should be the super key of the table.
c.) Each cell of a table should have a single value.
d.) The primary key of the table should be composed of one column.
Answers
The criteria for a table being in second normal form (2NF) is that every non-key attribute should be functionally dependent on the whole key.
In other words, option b is the correct criteria for second normal form (2NF). According to this criteria, every functional dependency where attribute X is functionally dependent on attribute Y, attribute X should be the super key of the table. This ensures that each non-key attribute is fully dependent on the entire primary key, eliminating partial dependencies and ensuring data integrity.
It's important to note that options a, c, and d are not specific to the second normal form and do not capture the essence of the criteria for achieving 2NF.
Know more about second normal form here:
https://brainly.com/question/32284517
#SPJ11
how to calculate the number of pistons required to lift in pltw poe
Answers
The calculation for the number of pistons required to lift in PLTW POE depends on specific design factors and cannot be determined without more information.
What factors need to be considered when calculating the number of pistons required for lifting in PLTW POE?To calculate the number of pistons required to lift in PLTW POE (Project Lead The Way Principles of Engineering), you would need specific information about the system design, including factors such as the weight to be lifted, desired lifting capacity, force requirements, and mechanical advantage.
The calculation would involve considering the forces involved, the efficiency of the system, and any additional factors such as safety margins or load distribution.
Without more specific information about the system and its requirements, it is not possible to provide a generic calculation for the number of pistons required.
It is recommended to refer to the PLTW POE curriculum or consult the project guidelines and resources provided by your instructor or educational institution for specific calculations and guidance on determining the number of pistons required for lifting in a given scenario.
Learn more about PLTW POE depends
brainly.com/question/30409110
#SPJ11
The unit of solar radiation?
Answers
Answer: The solar irradiance is measured in watt per square metre (W/m2) in SI units. Solar irradiance is often integrated over a given time period in order to report the radiant energy emitted into the surrounding environment (joule per square metre, J/m2) during that time period.
Explanation: hope that helped!
5. The pin support at A allows _______. Select the one that applies. (a) displacement in the x direction (b) rotation about its central axis (c) displacement in the y direction (d) none of the above 6. The support at B does not allow _______. Select the one that applies. (a) displacement in the x direction (b) rotation about its central axis (c) displacement in the y direction
Answers
Answer: Diagram associated with your question is attached below
5) B
6) C
Explanation:
5) The pin support at A allows ; Rotation about its central axis
This is because pin supports does not allow the translation of its structural member in any direction i.e. y or x but only rotation about its axis
6) The support at B does not allow displacement in y direction
This is because roller support allows displacement only in the direction that they are situated and in this case it is the x - direction
An anemometer mounted 10 m above a surface with crops, hedges, and shrubs, shows a wind speed of 5 m/s. Assuming 15°C and 1 atm pressure, determine the following for a wind turbine with hub height 80 m and rotor diameter of 80 m. Estimate the wind speed and the specific power in the wind (W/m2) at the highest point that the rotor blade reaches. Assume no air density change over these heights.
Answers
Answer : The wind speed and the specific power in the wind (W/m²) at the highest point that the rotor blade reaches are 5m/s and 11.47 W/m² respectively.
Explanation: Given,Anemometer mounted 10m above the surface shows wind speed = 5m/sHeight of wind turbine (h) = 80mRotor diameter = 80mAtmospheric conditionsTemperature (T) = 15°CPressure (P) = 1 atmWe have to find the following for a wind turbine with hub height 80 m and rotor diameter of 80 m.Estimate the wind speed and the specific power in the wind (W/m²) at the highest point that the rotor blade reaches.Since air density is assumed to be the same over the given heights, the wind speed can be assumed to be the same as well.
The effect of height is only considered for the calculation of power. Thus, the wind speed at the highest point reached by the rotor blade is given by;wind speed = 5 m/sNow, we will calculate the power output.The formula for the kinetic power in the wind is given by;P = 1/2 ρAV³Where,ρ = air densityA = swept areaV = wind speedAt 10 m height, the air density is given by;ρ₁ = P / RTρ₁ = (1 atm) / (287 J/kg·K × (15°C + 273))ρ₁ = 1.16 kg/m³The swept area of the rotor is given by;A = πr²Where,r = radius = d / 2 = 80 / 2 = 40mA = π(40)²A = 5026.55 m²The kinetic power is given by;P = 1/2 ρAV³P = 1/2 × 1.16 × 5026.55 × (5)³P = 144187.93 WTotal power is given by;P_total = η PHere,η = efficiency = 0.4 (40%)Thus,P_total = 0.4 × 144187.93P_total = 57675.17 WThe specific power is defined as power per unit area.
Thus, the specific power is given by;Specific power = P_total / ASpecific power = 57675.17 / 5026.55Specific power = 11.47 W/m²Therefore, the wind speed and the specific power in the wind (W/m²) at the highest point that the rotor blade reaches are 5m/s and 11.47 W/m² respectively.
Learn more about wind speed here https://brainly.in/question/3480812
#SPJ11
Size a bioretention filter (without a forebay) to receive a 2,025-m^3wQ, and with a drain time of 1 day from the new development. The design hydraulic conductivity of the media is 0.2-m/d and already includes a safety factor. 75% of the WQv is to be stored over the filter before treatment. The maximum design depth of ponding is 300-mm (=0.3-m). Use a soil media thickness of 0.75-m for the filter.
a 1000 m²
b. 7235 m²
c. 5425 m²
d. 1520 m²
e. Cannot be determined with the information provided
Answers
Answer:
jdkdhdjdieiehshsisishsususushdhshsusihshshshsjsjdjdhdhdueudjddjjdjsosjshdjdjdjxjxjxhdjdkdkdjjjxjdkdjdjdjdjdjdjdjdhd shxjdksjxnckdodjfidoeidjxksosbxnsksodjjdpspwoeoeuridjcklslsjdjdoebfndep
Explanation:
jxjsisjdjxjcjdkdkjdksoskskdks
the three elements to perimeter security include all except:
Answers
The three elements to perimeter security include all except **physical barriers**.
Perimeter security typically consists of three key elements: **detection**, **deterrence**, and **response**. Detection involves the use of various technologies and systems to identify potential threats or breaches in the perimeter, such as intrusion detection sensors, video surveillance cameras, and motion detectors. Deterrence focuses on implementing measures and strategies to discourage unauthorized access, such as fencing, access control systems, and security signage. Response refers to the planned actions and procedures to be taken in the event of a security breach, including alarm systems, security personnel, and incident response protocols. Physical barriers, such as walls, fences, and gates, are often considered an integral part of perimeter security but are not one of the three elements specifically mentioned.
Learn more about Perimeter security here:
https://brainly.com/question/14989492
#SPJ11
brief comparison of the the behavioral implementation of a multiplexer described in the background section with the multiplexer you described in the previous lab using structural and dataflow.
Answers
A dataflow architecture uses only concurrent signal assignment statements. A behavioral architecture uses only process statements. A structural architecture uses only component instantiation statements.
Dataflow modelling uses Boolean equations as design specifications. For eg. to design AND gate you use the equation y <= a & b ; Statements are executed concurrently. Behavioural modelling executes statements sequentially. They are written inside a process statement. Structural modelling uses logic diagrams.
Therefore, A behavioral architecture uses only process statements. A structural architecture uses only component instantiation statements.
Learn more about dataflow on:
https://brainly.com/question/31759863
#SPJ4
.If a steganography application used lossless encryption, the output carrier would be __________ compared to the original carrier file.
Group of answer choices
identical
unusable
larger
smaller
Answers
Answer: If a steganography application used lossless encryption, the output carrier would be identical compared to the original carrier file.
Explanation : Steganography is the study of concealing secret data inside an ordinary, non-secret message or information. Steganography is a common technique used to hide information or data within image files. The term "steganography" comes from the Greek language and means "covered writing."The basic requirements for the implementation of Steganography are as follows:Imperceptibility: The changes made to the carrier data should be imperceptible to a human observer.Capacity: The amount of data that can be concealed in the carrier data should be large.Security: The information hidden inside the carrier data should not be easy to detect or extract.For the given problem, if a steganography application used lossless encryption, the output carrier would be identical compared to the original carrier file. Lossless compression algorithms minimize file size while maintaining the original quality of the file.
Learn more about Steganography here https://brainly.in/question/9509627
#SPJ11