The switch opens at t = 0 after a very long time. Find v(t) for t > 0. Draw circuits clearly for each step using 4-step approach to illustrate the situation when t<0 and t>0 when doing circuit analysis for full credit. Write final answers in the box provided. [10 pts] 6 V 30 k 0 47 (1) 60 k 5 μF 60 k
Answers
The voltage of switch function v(t) for t > 0 is approximately 5.992 V. The 5 μF capacitor does not affect the voltage at steady-state.
To analyze the circuit and find the voltage function v(t) for t > 0, let's go through the 4-step approach and consider the circuit at t < 0 and t > 0 separately.
Step 1: Circuit at t < 0 (before the switch opens)
At t < 0, the switch is closed, and the capacitor is assumed to have been charged to a steady-state. In this case, the capacitor behaves like an open circuit, and the 60 kΩ resistor is effectively disconnected.
The circuit at t < 0 can be represented as follows:
Step 2: Circuit at t = 0 (when the switch opens)
At t = 0, the switch opens. The capacitor retains its voltage, and the voltage across it remains constant. However, the circuit topology changes as the capacitor now acts as a voltage source with an initial voltage of 6 V.
The circuit at t = 0 can be represented as follows:
Step 3: Circuit at t > 0 (after the switch opens)
At t > 0, the switch remains open, and the circuit reaches a new steady-state. The capacitor acts like an open circuit in the steady-state, and the 60 kΩ resistor is effectively disconnected.
The circuit at t > 0 can be represented as follows:
Step 4: Solving for v(t) for t > 0
To find the voltage function v(t) for t > 0, we can use the voltage divider rule to determine the voltage across the 30 kΩ resistor.
The voltage across the 30 kΩ resistor is given by:
v(t) = (30 kΩ / (30 kΩ + 47 Ω)) * 6 V
Simplifying the equation:
v(t) = (30000 / 30047) * 6 V
v(t) ≈ 5.992 V (approximately)
Therefore, the voltage function v(t) for t > 0 is approximately 5.992 V.
To know more about switch click here:
https://brainly.com/question/33623724
#SPJ11
Related Questions
A particle is moving toward the origin along the positive direction of the X axis. The displacement of this particle is negative. O it depends on the speed. O positive. O it depends on the frame of reference.
Answers
The displacement of a particle moving towards the origin in the positive direction of the x-axis is negative.
A frame of reference is a coordinate system in which motion is observed. In the case of a particle moving towards the origin in the positive direction of the x-axis, the displacement is negative.The displacement of a particle moving towards the origin in the positive direction of the x-axis is negative.
A frame of reference is a coordinate system in which motion is observed. In the case of a particle moving towards the origin in the positive direction of the x-axis, the displacement is negative.If we assume that the particle is moving with a uniform speed, the displacement is negative in all reference frames.
If the particle moves faster or slower with respect to the reference frame, its displacement may be positive or negative.
However, the speed is constant in all reference frames. In the case of a particle moving towards the origin along the positive direction of the x-axis, the displacement is always negative regardless of the reference frame. It is the direction of motion that determines the sign of the displacement.
Know more about displacement here,
https://brainly.com/question/11934397
#SPJ11
AP1: a) Write down the Electric and Magnetic fields for a plane wave travelling in +z direction that is linearly polarized in the x direction. b) Calculate the Poynting vector for this EM wave c) Calculate the total energy density for this wave d) Verify that the continuity equation is satisfied for this wave.
Answers
a) Electric and Magnetic fields for a plane wave travelling in +z direction is
E₀ cos(kz - ωt) î and B₀ cos(kz - ωt) ĵ.
b)Poynting vector for this EM wave is (1/μ₀) E₀ B₀ (cos)² (k z - - ω t ) k
c)total energy density for this wave is (1/2μ₀) (E₀² + B₀²) cos²(kz - ωt)
d)continuity equation for this wave is ∂u/∂t + ∇ · S = 0
a) For a plane wave traveling in the +z direction that is linearly polarized in the x direction, the electric field (E) and magnetic field (B) can be written as:
Electric field: E(x, y, z, t) = E₀ cos(kz - ωt) î
Magnetic field: B(x, y, z, t) = B₀ cos(kz - ωt) ĵ
where,
E₀ and B₀ are the amplitudes of the electric and magnetic fields
k is the wave number
ω is the angular frequency
î and ĵ are unit vectors in the x and y directions, respectively.
b) The Poynting vector (S) for this electromagnetic wave can be calculated as:
S(x, y, z, t) = (1/μ₀) E(x, y, z, t) × B(x, y, z, t)
where
μ₀ is the permeability of free space
× denotes the cross product.
Since E and B are perpendicular to each other, their cross product will be in the z direction.
S(x, y, z, t) = (1/μ₀) E₀ B₀ (cos)² (k z - - ω t ) k
where,
k is the unit vector in the z direction.
c) The total energy density (u) for this wave can be calculated using the equation:
u(x, y, z, t) = (1/2μ₀) (E(x, y, z, t)² + B(x, y, z, t)²)
Substituting the values of E and B into the equation, we get:
u(x, y, z, t) = (1/2μ₀) (E₀² + B₀²) cos²(kz - ωt)
d) The continuity equation for electromagnetic waves states that the rate of change of energy density with respect to time plus the divergence of the Poynting vector should be zero.
Mathematically, it can be written as:
∂u/∂t + ∇ · S = 0
Taking the derivatives and divergence of the expressions obtained in parts b) and c) we can verify if the continuity equation is satisfied for this wave.
learn more about magnetic field :
https://brainly.com/question/19542022
#SPJ4
In an RC circuit, if we were to change the resistor to one with a larger value, we would expect that:
A. The area under the curve changes
B. The capacitor discharges faster
C. The capacitor takes longer to achieve Qmax
D. The voltage Vc changes when the capacitor charges.
Answers
The correct answer is option (C): The capacitor takes longer to achieve Qmax. In an RC circuit, the resistor and capacitor are connected in series.
When a capacitor is charging in an RC circuit, it gradually reaches its maximum charge, denoted as Qmax, over time.
If we were to change the resistor to one with a larger value, we would expect the following:
A. The area under the curve changes: This statement is not necessarily true. The area under the curve, which represents the charge stored in the capacitor over time, depends on the time constant of the circuit (RC time constant).
Changing the resistor value affects the time constant, but it does not directly determine whether the area under the curve changes. Other factors, such as the voltage applied and the initial charge on the capacitor, can also influence the area under the curve.
B. The capacitor discharges faster: This statement is not applicable to changing the resistor value. The discharge rate of a capacitor in an RC circuit is primarily determined by the value of the resistor when the capacitor is being discharged, not when it is being charged.
C. The capacitor takes longer to achieve Qmax: This statement is true. In an RC circuit, the time constant (τ) is determined by the product of the resistance (R) and the capacitance (C) values (τ = RC).
A larger resistor value will increase the time constant, which means it will take longer for the capacitor to charge to its maximum charge (Qmax). So, the capacitor will indeed take longer to achieve Qmax.
D. The voltage Vc changes when the capacitor charges: This statement is true. When a capacitor charges in an RC circuit, the voltage across the capacitor (Vc) gradually increases until it reaches the same value as the applied voltage.
Changing the resistor value affects the charging time constant, which in turn affects the rate at which the voltage across the capacitor changes during charging. Therefore, changing the resistor value will impact the voltage Vc during the charging process.
In summary, the correct answer is C. The capacitor takes longer to achieve Qmax.
To learn more about RC circuit visit:
brainly.com/question/2741777
#SPJ11
A wire in the shape of an " \( \mathrm{M} \) " lies in the plane of the paper as shown in the figure. It carries a current of \( 2.00 \mathrm{~A} \), flowing from points \( A \) to \( B \), to \( C \)
Answers
The magnetic field at point P, which is inside the wire's loop, will be directed into the page or downward.
The wire in the shape of an "M" lies in the plane of the paper as shown in the figure. It carries a current of 2.00 A, flowing from points A to B, to C.What will be the direction of the magnetic field at point P due to the current-carrying conductor in the figure?We can apply the right-hand thumb rule to find the direction of the magnetic field at point P due to the current-carrying conductor in the figure.
The right-hand thumb rule states that if the thumb of the right hand is pointed in the direction of the current, the fingers will wrap around the conductor in the direction of the magnetic field.So, the magnetic field lines will flow around the wire in a counter clockwise direction (from points B to C to A). As a result, the magnetic field at point P, which is inside the wire's loop, will be directed into the page or downward. Therefore, the answer is "into the page or downward."
Learn more about magnetic field here,
https://brainly.com/question/14411049
#SPJ11
A 75kg stuntman falls 15m from the roof of a building. He then lands on an inflatable crash mat, which brings him to a stop in an additional 3.0m. What force must the crash mat provide to accomplish this?
Answers
To calculate the force the crash mat must provide, the principle of conservation of energy is used. The crash mat must provide a force of 4,410 N to bring the stuntman to a stop.
The potential energy lost by the stuntman as he falls is converted into work done by the crash mat to bring him to a stop.
The potential energy lost by the stuntman is given by the formula:
Potential Energy (PE) = mass (m) * acceleration due to gravity (g) * height (h)
It is given that Mass of the stuntman (m) = 75 kg, Acceleration due to gravity (g) = 9.8 m/s², Height fallen (h1) = 15 m, Additional height to stop (h2) = 3.0 m
The total potential energy lost by the stuntman is the sum of the potential energy lost while falling and the potential energy lost while coming to a stop:
Total Potential Energy Lost = m * g * h1 + m * g * h2
Substituting the given values:
Total Potential Energy Lost = 75 kg * 9.8 m/s² * 15 m + 75 kg * 9.8 m/s² * 3.0 m
Total Potential Energy Lost = 11,025 J + 2,205 J
Total Potential Energy Lost = 13,230 J
Since the crash mat brings the stuntman to a stop, the work done by the crash mat must be equal to the total potential energy lost.
Work done by the crash mat = Total Potential Energy Lost = 13,230 J
The work done by a force is equal to the force multiplied by the distance over which the force acts. In this case, the distance is the additional 3.0 m the stuntman comes to a stop:
Force * 3.0 m = 13,230 J
Force = 13,230 J / 3.0 m
Force ≈ 4,410 N
Therefore, the crash mat must provide a force of approximately 4,410 N to bring the stuntman to a stop.
To learn more about force: https://brainly.com/question/12785175
#SPJ11
A grinding wheel is a uniform cylinder with a radius of 7.20 cm and a mass of 0.350 kg <3 of 3 Constants Calculate its moment of inertia about its center. Express your answer to three significant figures and include the appropriate units. Calculate the applied torque needed to accelerate it from rest to 1750 rpm in 6.80 s. Take into account a frictional torque that has been measured to slow down the wheel from 1500 rpm to rest in 62.0 s Express your answer to three significant figures and include the appropriate units.
Answers
Plugging in the given values, we have I = (1/2)(0.350 kg)(0.072 m)² = 0.055 kg·m². This is the moment of inertia of the grinding wheel about its center.
To calculate the applied torque (τ) needed to accelerate the wheel, we use the equation τ = Iα, where α is the angular acceleration. The initial angular velocity is 0 (since the wheel starts from rest), and the final angular velocity is (1750 rpm)(2π rad/min) = (1750)(2π/60) rad/s. The time taken (t) is 6.80 s. Using the formula α = (ω - ω₀)/t, where ω is the final angular velocity and ω₀ is the initial angular velocity, we can calculate the angular acceleration. Substituting the values into τ = Iα, we can find the applied torque.
The frictional torque (τ_friction) that slows down the wheel is also given by τ_friction = Iα, where α is the angular acceleration. The initial angular velocity is (1500 rpm)(2π/60) rad/s, the final angular velocity is 0 (since the wheel comes to rest), and the time taken is 62.0 s. Using the formula α = (ω - ω₀)/t, we can calculate the angular acceleration. Substituting the values into τ_friction = Iα, we can find the frictional torque.
The applied torque is the difference between the torque needed for acceleration and the frictional torque: τ_applied = τ - τ_friction.
By performing the calculations, taking into account the given values and equations, we can determine the applied torque needed to accelerate the wheel and the effect of the frictional torque.
Learn more about torque here:
https://brainly.com/question/30338175
#SPJ11
When the spin direction of the disk was changed, the direction of the precession also changed. Why?
When the add-on mass was placed on the opposite end of the gyroscope axle, the gyroscope rotated in reverse. Why?
Hint: direction of angular momentum of the disk, direction of torque
Answers
The change in the spin direction of the disk results in a change in the direction of precession due to the conservation of angular momentum.
Angular momentum is a vector quantity, meaning it has both magnitude and direction. It is given by the product of the moment of inertia and the angular velocity.
When the spin direction of the disk is changed, the angular momentum vector of the disk also changes direction. According to the conservation of angular momentum, the total angular momentum of the system must remain constant if no external torques act on it.
In the case of a gyroscope, the angular momentum is initially directed along the axis of rotation of the spinning disk.
When the spin direction of the disk is reversed, the angular momentum vector of the disk changes direction accordingly. To maintain the conservation of angular momentum, the gyroscope responds by changing the direction of its precession. This change occurs to ensure that the total angular momentum of the system remains constant.
Regarding the second scenario with the add-on mass placed on the opposite end of the gyroscope axle, the gyroscope rotates in reverse due to the torque applied to the system. Torque is the rotational equivalent of force and is responsible for changes in angular momentum. Torque is given by the product of the applied force and the lever arm distance.
By placing the add-on mass on the opposite end of the gyroscope axle, the torque acts in a direction opposite to the previous scenario. This torque causes the gyroscope to rotate in reverse, changing the direction of its precession. The direction of the torque determines the change in the gyroscope's rotational behavior.
To learn more about angular momentum visit:
brainly.com/question/29563080
#SPJ11
A 2.5 mm diamotor copper wire carries a 39 A current uniform across its cross section) Part A Determine the magnetic field at the surface of the wire.
Express your answer using two significant figures. B = _______ T Part B Determine the magnetic field inside the wire, 0.50 mm below the surface Express your answer using two significant figures.
Answers
At the surface of the copper wire, the magnetic field strength is approximately 0.0031 Tesla. The magnetic field strength inside the copper wire, at a depth of 0.50 mm below its surface, is approximately 0.0041 Tesla.
Diameter of copper wire = 2.5 mm
Radius of copper wire, r = 1.25 mm
Current flowing through the wire, I = 39 A
Cross-sectional area of the wire, A = πr² = 4.9087 × 10⁻⁶ m²
Part A: The magnetic field at the surface of the wire is given by the formula,
B = μ₀I / 2r, where μ₀ is the magnetic permeability of free space.
μ₀ = 4π × 10⁻⁷ Tm/A
B = (4π × 10⁻⁷ Tm/A)(39 A) / (2 × 1.25 × 10⁻³ m)
B = 3.1 × 10⁻³ T
B = 0.0031 T
Therefore, at the surface of the copper wire, the magnetic field strength is approximately 0.0031 Tesla.
Part B: The magnetic field inside the wire is given by the formula,
B = μ₀I / 2r, where r is the distance from the center of the wire.
Let's substitute the given values in the formula and r = 1.25 × 10⁻³ m - 0.50 × 10⁻³ m = 0.75 × 10⁻³ m.
B = (4π × 10⁻⁷ Tm/A)(39 A) / (2 × 0.75 × 10⁻³ m)
B = 4.1 × 10⁻³ T
B = 0.0041 T
Therefore, the magnetic field strength inside the copper wire, at a depth of 0.50 mm below its surface, is approximately 0.0041 Tesla.
Learn more about magnetic field at: https://brainly.com/question/7645789
#SPJ11
What do you need to find the intensity of an electromagnetic wave?
Both the electric and magnetic field strengths.
Either the electric or magnetic field strength.
Only the electric field strength.
Only the magnetic field strength.
Answers
To find the intensity of an electromagnetic wave, we need to know the electric and magnetic field strengths as they are interdependent. The correct option is 1) Both the electric and magnetic field strengths.
The intensity of an electromagnetic wave is given by the energy transferred per unit area per unit time and is proportional to the square of the electric and magnetic field strengths. Therefore, if either the electric or magnetic field strength is missing, it will be impossible to determine the intensity accurately. The electric and magnetic fields oscillate perpendicular to each other and the direction of propagation of the wave. They have the same amplitude, frequency, and wavelength, but they differ in phase.
The intensity of an electromagnetic wave can also be determined by measuring the average power per unit area over a period. In summary, both electric and magnetic field strengths are required to calculate the intensity of an electromagnetic wave accurately. It is important to note that these fields are interdependent on each other, and a change in one can affect the other. Therefore, accurate measurements are crucial in the determination of the intensity of electromagnetic waves.
Learn more about electromagnetic wave here:
https://brainly.com/question/29774932
#SPJ11
When your instructor came to your house, she was approaching straight at you on a very fast-moving car and was frantically making a monotone sound with a pipe with one open end and one closed end, whose length was 0.67 m. According to her text message, she was making the 7th harmonic. But to you, it sounded like the sound was in its 9th harmonic. How fast was she moving? Use 343 m/s for the speed of sound. O 76 m/s 0 440 m/s 270 m/s 098 m/s
Answers
The instructor was moving at a speed of approximately 76 m/s.
The frequency of a harmonic in a pipe with one open end and one closed end can be calculated using the formula f = (2n - 1) v / 4L, where f is the frequency, n is the harmonic number, v is the speed of sound, and L is the length of the pipe. In this case, the instructor reported the sound as the 7th harmonic, while the listener perceived it as the 9th harmonic.
Let's set up two equations based on the given information. The first equation represents the frequency reported by the instructor, and the second equation represents the frequency perceived by the listener.
For the instructor: f₁ = (2 × 7 - 1) v / 4L
For the listener: f₂ = (2 × 9 - 1) v / 4L
By dividing the second equation by the first equation, we can eliminate the variables v and L:
f₂ / f₁ = [(2 × 9 - 1) / (2 × 7 - 1)]
Simplifying the equation, we find:
f₂ / f₁ = 17 / 13
Since the speed of sound (v) is given as 343 m/s, we can solve for the ratio of frequencies and find:
f₂ / f₁ = v₂ / v₁ = 17 / 13
Therefore, the ratio of the velocities is:
v₂ / v₁ = 17 / 13
Now we can plug in the given value of v₁ = 343 m/s and solve for v₂:
v₂ = (v₁ × 17) / 13
v₂ = (343 × 17) / 13 ≈ 76 m/s
Hence, the instructor was moving at a speed of approximately 76 m/s.
Learn more about speed here:
https://brainly.com/question/32673092
#SPJ11
A glass sheet 1.30 μm thick is suspended in air. In reflected light, there are gaps in the visible spectrum at 547 nm and 615.00 nm. Calculate the minimum value of the index of refraction of the glass sheet that produces this effect.
Answers
The case of light reflected from the upper surface of the film, we found that the minimum value of the refractive index of the glass sheet that produces the gaps in the visible spectrum at 547 nm and 615.00 nm is 1.466. Therefore, we can conclude that this is the answer.
Given data:Thickness of glass sheet (t) = 1.30 μmGaps in the visible spectrum at 547 nm and 615.00 nmWe know that when light is reflected from a thin film, we see colored fringes due to interference of light waves.
The conditions for minimum reflection from a thin film are:When the thickness of the film is odd multiples of λ/4 i.e. t = (2n+1)(λ/4)when there is no phase change at the reflection i.e. when the reflected wave is in phase with the incoming wave.
Assuming the light is reflecting from the upper surface of the film, we can find the refractive index (n) of the glass sheet using the formula: t = [(2n + 1) λ1]/4where λ1 is the wavelength of light in air.The gaps are seen at λ = 547 nm and λ = 615 nm
Therefore, applying above formulae for both wavelengths and taking the difference of the refractive indices: t = [(2n + 1) λ1]/4When λ = 547 nm ⇒ λ1 = λ/n = 547/nTherefore, t = [(2n + 1) λ]/4⇒ 1.3 × 10⁻⁶ = [(2n + 1) × 547 × 10⁻⁹]/4⇒ 2n + 1 = 4 × 1.3/547 ⇒ 2n + 1 = 0.0095n = 2⇒ Refractive index (n) = λ/λ1 = 547/λ1t = [(2n + 1) λ1]/4When λ = 615 nm ⇒ λ1 = λ/n = 615/n
Therefore, t = [(2n + 1) λ]/4⇒ 1.3 × 10⁻⁶ = [(2n + 1) × 615 × 10⁻⁹]/4⇒ 2n + 1 = 4 × 1.3/615 ⇒ 2n + 1 = 0.0085n = 2⇒ Refractive index (n) = λ/λ1 = 615/nDifference in refractive indices (Δn) = n(λ=547) - n(λ=615)= 547/n - 615/n = 547/2 - 615/2= -34To produce the effect of minimum reflection, the minimum value of the refractive index of the glass sheet is 1.5 - 0.034 = 1.466.
For the case of light reflected from the upper surface of the film, we found that the minimum value of the refractive index of the glass sheet that produces the gaps in the visible spectrum at 547 nm and 615.00 nm is 1.466. Therefore, we can conclude that this is the answer.
Learn more about Spectrum here,
https://brainly.com/question/19042165
#SPJ11
A microscope has a circular lens with focal length 31.6 mm and diameter 1.63 cm. What is the smallest feature in micrometers (µm) that can be resolved with the microscope when specimens are observed with light of wavelength 665 nm? (State answer with 2 digits right of decimal. Do not include unit in answer.)
Answers
A microscope has a circular lens with focal length 31.6 mm and diameter 1.63 cm. the smallest feature that can be resolved by the microscope is approximately 3.13 µm.
The smallest feature that can be resolved by a microscope is determined by the concept of angular resolution, which is dependent on the wavelength of light and the numerical aperture of the lens system. The formula for the angular resolution is given by:
Angular resolution = 1.22 * (Wavelength / Numerical aperture)
The numerical aperture (NA) is a characteristic of the microscope lens system and can be calculated as the ratio of the lens diameter to twice the focal length:
Numerical aperture = Lens diameter / (2 * Focal length)
Given the values in the problem, the diameter of the lens is 1.63 cm and the focal length is 31.6 mm (or 3.16 cm). Plugging these values into the numerical aperture formula, we get:
Numerical aperture = 1.63 cm / (2 * 3.16 cm) ≈ 0.258
Now, we can calculate the angular resolution using the given wavelength of light (665 nm or 0.665 µm) and the numerical aperture:
Angular resolution = 1.22 * (0.665 µm / 0.258) ≈ 3.13 µm
Therefore, the smallest feature that can be resolved by the microscope is approximately 3.13 µm.
Learn more about angular resolution here:
https://brainly.com/question/30657782
#SPJ11
a) A flat roof is very susceptible to wind damage during a thunderstorm and/or tornado. If a flat roof has an area of 780 m2 and winds of speed 41.0 m/s blow across it, determine the magnitude of the force exerted on the roof. The density of air is 1.29 kg/m3.
N
(b) As a result of the wind, the force exerted on the roof is which of the following?
upward
downward
Answers
During a thunderstorm or tornado, a flat roof with an area of 780 m2 is at risk of wind damage. The magnitude of the force exerted on the roof is 679,024.7 N. The force exerted on the roof is in the downward direction.
To calculate the force exerted on the flat roof, we need to determine the wind pressure first. Wind pressure can be calculated using the equation: [tex]Pressure = 0.5 * density * velocity^2[/tex], where the density of air is given as [tex]1.29 kg/m^3[/tex] and the velocity is 41.0 m/s. Plugging in these values, we find the wind pressure to be approximately 872.485 Pa.
Next, we can calculate the force exerted on the roof by multiplying the wind pressure by the area of the roof. The area of the roof is given as [tex]780 m^2[/tex]. Therefore, the force exerted on the roof can be calculated as: Force = Pressure * Area. Substituting the values, we get: Force = [tex]872.485 Pa * 780 m^2 = 679,024.7 N[/tex].
The force exerted on the flat roof during the thunderstorm/tornado is downward since the wind blows across the roof and exerts a pressure on it in the downward direction. Therefore, the correct answer is (b) downward.
Learn more about force here:
https://brainly.com/question/30507236
#SPJ11
An electron (mass 9 x 10⁻³¹ kg) is traveling at a speed of 0.91c in an electron accelerator. An electric force of 1.6 x 10 N is applied in the direction of motion while the electron travels a distance of 2 m. You need to find the new speed of the electron. Which of the following steps must be included in your solution to this problem? (a) Calculate the initial particle energy Yimc of the electron. (b) Calculate the final particle energy y&mc? of the electron. (c) Determine how much time it takes to move this distance. (d) Use the expression m[512 to find the kinetic energy of the electron. (e) Calculate the net work done on the electron. (f) Use the final energy of the electron to find its final speed. What is the new speed of the electron as a fraction of c?
Answers
The new speed of the electron as a fraction of c is 0.9655.
Mass of electron = m = 9 x 10⁻³¹ kg
Speed of electron = u = 0.91c
Electric force = F = 1.6 x 10 N
Crossing distance = s = 2 m
Electric force = F = ma
where, F = Electric force, m = Mass of the electron, a = Acceleration of the electron.
Using above equation, we get, a = F/ma = F/m = 1.6 x 10 / 9 x 10⁻³¹ a = 1.78 x 10⁴ m/s²
Now, we can calculate the time taken by electron to travel a distance of 2m using s = ut + ½ at²
where, u = Initial speed of electron, t = Time taken by electron to travel distance s, a = Acceleration of electron, s = Distance travelled by electron.
So, t = s / (u/2 + ½ a)
We get, t = 2 / [0.91c/2 + 1/2 * 1.78 x 10⁴]
= 5.71 x 10⁻¹⁰ s
Kinetic energy = [m / √(1- (v/c)²)] c² - mc²
where, Kinetic energy = Final kinetic energy of electron, m = Mass of the electron, v = Final speed of the electron.
So, K.E = [9 x 10⁻³¹ / √(1-(v/c)²)] c² - (9 x 10⁻³¹) c²
Now, calculate the net work done on the electron. Wnet = K.E - K.Eo
where, Wnet = Net work done on electron, K.E = Final kinetic energy of electron, K.Eo = Initial kinetic energy of electron.
K.Eo = [9 x 10⁻³¹ / √(1-(u/c)²)] c² - (9 x 10⁻³¹) c²
we get, Wnet = [9 x 10⁻³¹ / √(1-(v/c)²)] c² - [9 x 10⁻³¹ / √(1-(u/c)²)] c²
Simplify this expression, Wnet = 0.5 x 9 x 10⁻³¹ [(1/√(1-(v/c)²)] c² - [(1/√(1-(u/c)²)] c²
= 0.5 x m [(1/√(1-(v/c)²)] c² - [(1/√(1-(u/c)²)] c²
Finally, use the work-energy principle. We know that, Wnet = ΔK.E
Wnet = Work done on the particle, ΔK.E = Change in kinetic energy of the particle.
Since the electron is being accelerated, the force acting on it is in the same direction as the direction of motion and hence, the work done is positive. So, we can write Wnet = K.E - K.Eo.
Now, put the values of Wnet, ΔK.E, K.E and K.Eo, we get,0.5 x m [(1/√(1-(v/c)²)] c² - [(1/√(1-(u/c)²)] c²
= [(9 x 10⁻³¹ / √(1-(v/c)²)] c² - [(9 x 10⁻³¹ / √(1-(u/c)²)] c² - [(9 x 10⁻³¹ / √(1-(u/c)²)] c²
Now, we can calculate the final kinetic energy of the electron, Kinetic energy = (Wnet + K.Eo)K.E = 0.5 x m [(1/√(1-(v/c)²)] c² + [(9 x 10⁻³¹ / √(1-(u/c)²)] c²K.E
= [9 x 10⁻³¹ / √(1-(v/c)²)] c²v/c
= √[1 - ((m/m+1)(c/u²t²))]v/c
= √[1 - ((9 x 10⁻³¹/10⁻³¹ + 1)(3 x 10⁸/(0.91 x 3 x 10⁸)² x (5.71 x 10⁻¹⁰)²))]v/c = 0.9655
Therefore, the new speed of the electron as a fraction of c is 0.9655.
Learn more about new speed of electron: https://brainly.com/question/29573654
#SPJ11
The counter-clockwise circulating current in a solenoid is increasing at a rate of 4.54 A/s. The cross-sectional area of the solenoid is 3.14159 cm², and there are 395 tums on its 21.4 cm length. What is the magnitude of the self-induced emf & produced by the increasing current? Answer in units of mV. Answer in units of mV part 2 of 2 Choose the correct statement 11 The & attempts to move the current in the solenoid in the clockwise direction x 2 The E tries to keep the current in the solenoid flowing in the counter-clockwise direction 03 The does not effect the current in the solenoid 4 Not enough information is given to determine the effect of the E By the right hand rule, the E produces mag- 5. netic fields in a direction perpendicular to the prevailing magnetic field
Answers
The emf tries to keep the current in the solenoid flowing in the counter-clockwise direction. When something moves in the opposite direction to the way in which the hands of a clock move round in known as counterclockwise.
To calculate the magnitude of the self-induced electromotive force (emf) produced by the increasing current in the solenoid, we can use Faraday's law of electromagnetic induction, which states that the emf induced in a coil is equal to the rate of change of magnetic flux through the coil.
The formula to calculate the emf is:
emf = -N * dΦ/dt
where N is the number of turns in the solenoid and dΦ/dt is the rate of change of magnetic flux.
Rate of change of current (di/dt) = 4.54 A/s (since current is increasing at this rate)
Cross-sectional area (A) = 3.14159 cm² = 0.000314159 m²
Length of the solenoid (l) = 21.4 cm = 0.214 m
Number of turns (N) = 395
First, we need to calculate the magnetic flux (Φ) through the solenoid.
The magnetic flux is given by the formula:
Φ = B * A
where B is the magnetic field and A is the cross-sectional area.
To calculate the magnetic field, we use the formula:
B = μ₀ * (N / l) * I
where μ₀ is the permeability of free space, N is the number of turns, l is the length of the solenoid, and I is the current.
Permeability of free space (μ₀) = 4π × 10⁻⁷ T·m/A
Calculations:
B = (4π × 10⁻⁷ T·m/A) * (395 / 0.214 m) * (4.54 A/s)
B ≈ 0.0332 T
Now, we can calculate the rate of change of magnetic flux (dΦ/dt):
dΦ/dt = B * A * (di/dt)
dΦ/dt = 0.0332 T * 0.000314159 m² * (4.54 A/s)
dΦ/dt ≈ 4.20 × 10⁻⁶ Wb/s
Finally, we can calculate the magnitude of the self-induced emf:
emf = -N * dΦ/dt
emf = -395 * (4.20 × 10⁻⁶ Wb/s)
emf ≈ -1.66 mV
The magnitude of the self-induced emf produced by the increasing current is approximately 1.66 mV.
Regarding the second part of your question, according to the right-hand rule, the self-induced emf tries to keep the current in the solenoid flowing in the same direction, which in this case is the counter-clockwise direction. So, the correct statement is: The emf tries to keep the current in the solenoid flowing in the counter-clockwise direction.
To knwo more baout electromotive force (emf)
https://brainly.com/question/31833293
#SPJ11
A 2.4 kg rock has a horizontal velocity of magnitude v=2.1 m/s when it is at point P in the figure, where r=4.1 m and θ= 45 degree. If the only force acting on the rock is its weight, what is the rate of change of its angular momentum relative to point O at this instant?
Answers
Therefore, the rate of change of the angular momentum relative to point O is zero.Answer: 0
The angular momentum of the rock relative to point O is given byL = r × p,where r is the position vector of the rock relative to point O, and p is the momentum of the rock relative to point O.We can express the momentum p in terms of the velocity v. Since the rock has a horizontal velocity of magnitude v=2.1 m/s, its momentum has a horizontal component of p = mv = (2.4 kg)(2.1 m/s) = 5.04 kg · m/s. There is no vertical component of the momentum, since the rock is moving horizontally, so we have p = (5.04 kg · m/s) i. Using the position vector r = (4.1 m) i + (4.1 m) j and the momentum p, we find thatL = r × p= [(4.1 m) i + (4.1 m) j] × (5.04 kg · m/s i)= 20.2 kg · m²/s k. where k is a unit vector perpendicular to the plane of the paper, pointing out of the page. The rate of change of the angular momentum relative to point O is given byτ = dL/dtwhere τ is the torque on the rock. Since the only force acting on the rock is its weight, which is directed downward, the torque on the rock is zero, so we haveτ = 0. Therefore, the rate of change of the angular momentum relative to point O is zero.Answer: 0
To know more about magnitude visit:
https://brainly.com/question/29665153
#SPJ11
A parallel plate capacitor, in which the space between the plates is filled with a dielectric material with dielectric constant k = 10.1, has a capacitor of C= 6.2μF and it is connected to a battery whose voltage is V = 5.9V and fully charged. Once it is fully charged, it is disconnected from the battery and without affecting the charge on the plates, dielectric material is removed from the capacitor. How much change occurs in the energy of the capacitor (final energy minus initial energy)? Express your answer in units of mJ (mili joules) using two decimal places
Answers
The change in energy of the capacitor (final energy minus initial energy) is 2.11 mJ.
When the dielectric material is removed from the capacitor, the capacitance decreases, and the voltage across the plates increases to keep the charge constant. Let's calculate the initial energy stored in the capacitor as well as the final energy stored in the capacitor.Energy stored by a capacitor is given by:U = 1/2 CV²Initial energy,U1 = 1/2 × 6.2 × (5.9)² U1 = 102.43 mJWhen the dielectric material is removed from the capacitor, the capacitance changes.
Capacitance without the dielectric material,C2 = C / k C2 = 6.2 μF / 10.1 C2 = 0.613 μFThe voltage across the plates increases.V2 = V × k V2 = 5.9 V × 10.1 V2 = 59.59 VFinal energy,U2 = 1/2 × 0.613 × (59.59)² U2 = 104.54 mJChange in energy,ΔU = U2 - U1 ΔU = 104.54 - 102.43 ΔU = 2.11 mJTherefore, the change in energy of the capacitor (final energy minus initial energy) is 2.11 mJ.
Learn more about Energy here,
https://brainly.com/question/2003548
#SPJ11
A 2100 kg truck is travelling at 31m/s [E] and collides with a 1500 kg car travelling 24m/s[E]. The two vehicles lock bumpers and continue as one object. What is the decrease in kinetic energy during the inelastic collision?
Answers
A 2100 kg truck is moving at 31m/s[E] and crashes into a 1500 kg car traveling at 24m/s[E]. The two cars lock bumpers and continue as one object. The decrease in kinetic energy during the inelastic collision is 870194 J. The law of conservation of momentum is used to determine the final velocity of the combined vehicles.
An inelastic collision is one in which the kinetic energy is not conserved. Instead of bouncing off each other, the two colliding objects stick together after the collision. The decrease in kinetic energy during an inelastic collision is related to the amount of energy that is transformed into other forms such as sound, heat, or deformation energy. During the inelastic collision between a 2100 kg truck and a 1500 kg car, the two vehicles lock bumpers and continue as one object. First, it is necessary to calculate the total initial kinetic energy before the collision occurs. Kinetic energy = 0.5 x mass x velocity²The kinetic energy of the truck before the collision = 0.5 x 2100 kg x (31 m/s)² = 1013395 J. The kinetic energy of the car before the collision = 0.5 x 1500 kg x (24 m/s)² = 864000 JThe total initial kinetic energy = 1013395 J + 864000 J = 1877395 JThe total mass of the two vehicles after the collision = 2100 kg + 1500 kg = 3600 kg. Now, we can calculate the final velocity of the combined vehicles after the collision using the law of conservation of momentum: Momentum before collision = Momentum after collision2100 kg x 31 m/s + 1500 kg x 24 m/s = 3600 kg x vfVf = (2100 kg x 31 m/s + 1500 kg x 24 m/s) / 3600 kgVf = 26.08 m/sThe kinetic energy of the combined vehicles after the collision = 0.5 x 3600 kg x (26.08 m/s)² = 1007201 J. Therefore, the decrease in kinetic energy during the inelastic collision is 1877395 J - 1007201 J = 870194 J.For more questions on kinetic energy
https://brainly.com/question/8101588
#SPJ8
A point charge of -4.00 nC is at the origin, and a second point charge of 6.00 nC is on the x axis at x = 0.830 m. Find the magnitude and direction of the electric field at each of the following points on the x axis. Part A
x₂ = 18.0 cm E(x₂) = _______ N/C
Part B
The field at point x₂ is directed in the a. +x direction.
b. -x direction.
Answers
A point charge of -4.00 nC is at the origin. Second point charge of 6.00 nC is on the x-axis at x = 0.830 m.
Electric field due to a point charge, k = 9 × 10^9 Nm²/C².
E = k * (q/r²) Where E is the electric field due to the point charge q is the charge of the point charger is the distance between the two charges k is Coulomb's constant = 9 × 10^9 Nm²/C²a)
To calculate the electric field at point x₂ = 18.0 cm, we need to find the distance between the two charges. It is given that one point charge is at the origin and the other is at x = 0.830 m. So, the distance between the two charges = (0.830 m - 0.180 m) = 0.65 m = 65 cm
The distance between the two charges is 65 cm = 0.65 m.
Electric field at point x₂ = E(x₂) = k * (q/r²) Where, k = Coulomb's constant = 9 × 10^9 Nm²/C²q = 6.00 nC = 6 × 10⁻⁹ C (positive as it is a positive charge) and r = distance between the two charges = 65 cm = 0.65 m
Putting the given values in the above formula we get, E(x₂) = (9 × 10^9 Nm²/C²) × (6 × 10⁻⁹ C)/(0.65 m)²E(x₂) = 123.86 N/C ≈ 124 N/C
Therefore, the electric field at point x₂ = 18.0 cm is 124 N/C (approx).
The direction of the electric field is towards the positive charge. Hence, the field at point x₂ is directed in the a. +x direction.
Learn more about electric fields: https://brainly.com/question/19878202
#SPJ11
A tennis ball, with a mass of 0.05 kg, is accelerated with a rate of 5000 m/s2. how much force was applied for the tennis ball ?
Answers
The amount of force that was applied to the tennis ball is 250 N.
To solve the given problem, we will use Newton's second law of motion, which states that the net force acting on an object is equal to the product of its mass and acceleration.
The formula for Newton's second law of motion is given as:
F = ma
Where,
F is the net force acting on the object
m is the mass of the object
a is the acceleration of the object
Mass of the tennis ball, m = 0.05 kg
Rate of acceleration, a = 5000 m/s²
Now, we can use Newton's second law of motion to calculate the net force that was applied to the tennis ball:
F = ma
= 0.05 kg × 5000 m/s²
= 250 N
Therefore, the amount of force that was applied to the tennis ball is 250 N.
Learn more about the Newton's second law:
brainly.com/question/25545050
#SPJ11
A car moving with a constant speed of 48 km/hr completes a circular track in 7.2 minutes. Calculate the magnitude of the acceleration of the car in the unit of m/s2.
Answers
The magnitude of the acceleration is found to be approximately 13.33m/s².
To calculate the magnitude of the acceleration of the car, we first need to convert the time taken to travel around the circular track into seconds. Given that the car completes the track in 7.2 minutes, we multiply this value by 60 to convert it to seconds. Thus, the time taken is 7.2 minutes * 60 seconds/minute = 432 seconds.
The formula for centripetal acceleration is given by a = v²/r, where "v" is the velocity of the car and "r" is the radius of the circular track. The velocity of the car can be converted from kilometers per hour (km/hr) to meters per second (m/s) by multiplying it by 1000/3600, since there are 1000 meters in a kilometer and 3600 seconds in an hour. Therefore, the velocity is 48 km/hr * 1000 m/km / 3600 s/h = 13.33 m/s.
Now we need to find the radius of the circular track. Since the car completes a full circle, the distance traveled is equal to the circumference of the track. The formula for circumference is given by C = 2πr, where "C" is the circumference and "r" is the radius.
Rearranging the formula, we have r = C/(2π). However, we are not given the value of the circumference, so we cannot calculate the exact radius.
Given the limited information, we can only calculate the magnitude of the acceleration in terms of the unknown radius. Therefore, the magnitude of the acceleration is a = (13.33 m/s)²/r.
Learn more about acceleration:
https://brainly.com/question/17123770
#SPJ11
The energy of a photon is given by 3600eV. What is the energy of the photon in the unit of J? Answer the value that goes into the blank: The energy of the photon is ×10 −15
J.
Answers
The energy of a photon is given as 3600 eV. The electron volt (eV) is a unit of energy commonly used in the field of particle physics and quantum mechanics. It represents the amount of energy gained or lost by an electron when it is accelerated through an electric potential difference of one volt.
To convert this energy to joules (J), we need to use the conversion factor between electron volts and joules. The conversion factor is 1 eV = 1.6 x[tex]10^(-19)[/tex] J. Multiplying the given energy of the photon (3600 eV) by the conversion factor, we can find the energy in joules:
Energy in J = 3600 eV * (1.6 x [tex]10^(-19)[/tex] J/eV)
Calculating this expression, we get:
Energy in J = 5.76 x [tex]10^(-16)[/tex] J
Therefore, the energy of the photon is 5.76 x[tex]10^(-16)[/tex]) J.
The electron volt (eV) is a unit of energy commonly used in the field of particle physics and quantum mechanics. It represents the amount of energy gained or lost by an electron when it is accelerated through an electric potential difference of one volt. On the other hand, the joule (J) is the standard unit of energy in the International System of Units (SI).
The conversion factor between eV and J is based on the charge of an electron and is derived from fundamental constants. Multiplying the energy in eV by the conversion factor allows us to convert it to joules. In this case, the energy of the photon is found to be 5.76 x [tex]10^(-16)[/tex] J.
The resulting value, written as ×[tex]10^(-15[/tex]) J, indicates that the energy is in the order of [tex]10^(-15[/tex]) J. This represents a very small amount of energy on the scale of everyday experiences, but it is significant in the realm of quantum phenomena, where particles and photons exhibit discrete energy levels.
Learn more about quantum mechanics here:
https://brainly.com/question/23780112
#SPJ11
a) Three long, parallel conductors carry currents of I = 2.04A. (end view of the conductors that has each current coming out of the page) . If a = 1.17cm, determine the magnitude of the magnetic field at point A.
b) Determine the magnitude of the magnetic field at point B.
c) Determine the magnitude of the magnetic field at point C.
Answers
The magnetic field at point A is 2.552 µT, the magnetic field at point B is 0.617 µT, and the magnetic field at point C is 1.211 µT.
a) Magnetic field at point A:
The magnetic field at point A due to wire 1 will be:
(µ_0/4π) × 2.04 / 0.0117N/Atm × 2π = 2.19 µT (out of the page)
The magnetic field at point A due to wire 2 will be:(µ_0/4π) × 2.04 / 0.0351N/Atm × 2π = 0.902 µT (into the page)
The magnetic field at point A due to wire 3 will be:(µ_0/4π) × 2.04 / 0.0585N/Atm × 2π = 0.54 µT (out of the page)
Therefore, the magnitude of the magnetic field at point A is (2.19 + 0.902 – 0.54) µT = 2.552 µT (out of the page)
(b) The magnetic field at point B:
The magnetic field at point B due to wire 1 will be:(µ_0/4π) × 2.04 / 0.0585N/Atm × 2π = 1.08 µT (into the page)
The magnetic field at point B due to wire 2 will be:(µ_0/4π) × 2.04 / 0.0351N/Atm × 2π = 0.902 µT (out of the page)
The magnetic field at point B due to wire 3 will be:(µ_0/4π) × 2.04 / 0.117N/Atm × 2π = 0.439 µT (out of the page)
Therefore, the magnitude of the magnetic field at point B is (1.08 – 0.902 + 0.439) µT = 0.617 µT (into the page)
c) The magnetic field at point C:
The magnetic field at point C due to wire 1 will be:(µ_0/4π) × 2.04 / 0.0117N/Atm × 2π = 2.19 µT (into the page)
The magnetic field at point C due to wire 2 will be:(µ_0/4π) × 2.04 / 0.117N/Atm × 2π = 0.439 µT (into the page)
The magnetic field at point C due to wire 3 will be:(µ_0/4π) × 2.04 / 0.0585N/Atm × 2π = 0.54 µT (into the page)
Therefore, the magnitude of the magnetic field at point C is:(2.19 – 0.439 – 0.54) µT = 1.211 µT (into the page)
The magnetic field at point A is 2.552 µT, the magnetic field at point B is 0.617 µT, and the magnetic field at point C is 1.211 µT.
To learn about the magnetic field here:
https://brainly.com/question/7645789
#SPJ11
Write the Lagrange's equation of lagrangian L(x, x, y,ỹ, t) and the constraint force f(x, y). Is the total energy conserved?, explain why. astogint force
Answers
The Lagrange's equation for a system described by a Lagrangian function L(x, ẋ, y, ỹ, t) is given by d/dt (∂L/∂ẋ) - (∂L/∂x) = f(x, y), where x and y are the generalized coordinates, ẋ and ỹ are their respective velocities, t is time, and f(x, y) represents the constraint force. The total energy of the system is conserved if the Lagrangian is not explicitly dependent on time (i.e., ∂L/∂t = 0).
Lagrange's equation is a fundamental principle in classical mechanics that describes the dynamics of a system in terms of its Lagrangian function. It states that the time derivative of the momentum (∂L/∂ẋ) minus the derivative of the Lagrangian with respect to the generalized coordinate (x) is equal to the external forces acting on the system, represented by the constraint force f(x, y).
Regarding the conservation of total energy, it depends on the properties of the Lagrangian. If the Lagrangian does not explicitly depend on time (i.e., ∂L/∂t = 0), then the total energy of the system, which is the sum of the kinetic and potential energies, is conserved. This is a consequence of Noether's theorem, which states that if a Lagrangian has a continuous symmetry, such as time translation symmetry, there is a conserved quantity associated with it.
However, if the Lagrangian explicitly depends on time, the total energy may not be conserved, and energy can be transferred into or out of the system. In such cases, the Lagrangian represents a system with time-dependent external forces or dissipative effects.
In summary, the Lagrange's equation describes the dynamics of a system using the Lagrangian function and constraint forces. The conservation of total energy depends on whether the Lagrangian is explicitly dependent on time or not. If it is not, the total energy is conserved; otherwise, energy may be transferred in or out of the system.
Learn more about Lagrangian here:
https://brainly.com/question/14309211
#SPJ11
An AC voltage of the form Av = 100 sin 1 000t, where Av is in volts and t is in seconds, is applied to a series RLC circuit. Assume the resistance is 410 , the capacitance is 5.20 pF, and the inductance is 0.500 H. Find the average power delivered to the circuit.
Answers
The average power delivered to the series RLC circuit, given an AC voltage of Av = 100 sin 1 000t with specific circuit parameters is 1.56 watts.
The average power delivered to a circuit can be determined by calculating the average of the instantaneous power over one cycle. In an AC circuit, the power varies with time due to the sinusoidal nature of the voltage and current.
First, let's find the angular frequency (ω) using the given frequency f = 1 000 Hz:
[tex]\omega = 2\pi f = 2\pi(1 000) = 6 283 rad/s[/tex]
Next, we need to calculate the reactance of the inductor (XL) and the capacitor (XC):
[tex]XL = \omega L = (6 283)(0.500) = 3 141[/tex] Ω
[tex]XC = 1 / (\omega C) = 1 / (6 283)(5.20 *10^{(-12)}) = 30.52[/tex] kΩ
Now we can calculate the impedance (Z) of the series RLC circuit:
[tex]Z = \sqrt(R^2 + (XL - XC)^2) = \sqrt(410^2 + (3 141 - 30.52)^2) = 3 207[/tex]Ω
The average power ([tex]P_{avg}[/tex]) delivered to the circuit can be found using the formula:
[tex]P_{avg} = (Av^2) / (2Z) = (100^2) / (2 * 3 207) = 1.56 W[/tex]
Therefore, the average power delivered to the series RLC circuit is 1.56 watts.
Learn more about average power here:
https://brainly.com/question/17008088
#SPJ11
Find a sinusoidal equation for a 40Kw/m wave energy in the sea.
Answers
To find the sinusoidal equation for a 40kW/m wave energy in the sea, we need to use the formula; y = A sin (ωt + Φ)where; A is the amplitude of the wave,ω is the angular frequency of the wave,t is time, andΦ is the phase angle.
The given value is 40kW/m wave energy in the sea. This represents the amplitude (A) of the wave. Therefore, A = 40.We also know that the period of the wave, T = 150m since it takes 150m for the wave to complete one cycle.To find the angular frequency (ω) of the wave, we use the formula;ω = 2π/T= 2π/150 = π/75Therefore, ω = π/75Putting these values in the formula;y = 40 sin (π/75 t + Φ)Where Φ is the phase angle, which is not given in the question.
Learn more on phase here:
brainly.in/question/37994359
#SPJ11
The fastest speed a human has ever run was 11.9 m/s. At what temperature would a nitrogen molecule (MM = 0.0280 kg/mole) travel at that speed? [?]=K. R = 8.31 J/(mol-K)
Answers
The temperature at which a nitrogen molecule would travel at the fastest human running speed of 11.9 m/s is approximately 348 Kelvin. So the temperature will be 348K.
To determine the temperature at which a nitrogen molecule would travel at the fastest human running speed, we can use the root mean square (RMS) velocity formula:
v_rms = √((3 * k * T) / m)
Where:
v_rms is the root mean square velocity,
k is the Boltzmann constant (1.38 × 10⁻²³ J/K),
T is the temperature in Kelvin,
m is the molar mass of the nitrogen molecule.
Given that the fastest human running speed is 11.9 m/s and the molar mass of nitrogen is 0.0280 kg/mol, we can rearrange the formula to solve for the temperature:
T = (m * v_rms²) / (3 * k)
Substituting the values, we have:
T = (0.0280 kg/mol * (11.9 m/s)²) / (3 * 8.31 J/(mol-K))
Calculating this expression, we find:
T ≈ 348 K
Therefore, the temperature at which a nitrogen molecule would travel at the same speed as the fastest human running speed is approximately 348 Kelvin.
To know more about Kelvin,
https://brainly.com/question/14132731
#SPJ11
5 kg of water at 68°C is put into a refrigerator with a compressor with power of 100 W. The water is frozen to ice at 0°C in 64.34 mins. Calculate the COP of the refrigerator. a) 11.0 12. e) 23.0 b) 35.0 c) 20.0 d) 32.0 g) 29.0 h) 14.0 | i) 17.0 f) 8.0 j) 26.0
Answers
The closest option from the given choices is (f) 8.0. To calculate the coefficient of performance (COP) of the refrigerator, we need to use the formula:
COP = (Useful cooling effect)/(Work input)
First, let's calculate the useful cooling effect. The water is initially at 68°C and is cooled down to 0°C. The specific heat capacity of water is approximately 4.186 J/g°C.
Useful cooling effect = mass of water × specific heat capacity of water × change in temperature
= 5000 g × 4.186 J/g°C × (68°C - 0°C)
= 1,129,240 J
Next, let's calculate the work input. The power of the compressor is given as 100 W, and the time taken for the water to freeze is 64.34 minutes. We need to convert the time to seconds.
Work input = power × time
= 100 W × (64.34 mins × 60 s/min)
= 38,604 J
Now we can calculate the COP:
COP = Useful cooling effect / Work input
= 1,129,240 J / 38,604 J
≈ 29.2
The closest option from the given choices is (f) 8.0.
Learn more about work here:
https://brainly.com/question/30073908?
#SPJ11
Write down the radar equation and analyze it. Discuss how to use
it to design the radar system
Answers
The radar equation is a fundamental equation used in radar systems to calculate the received power at the radar receiver. It relates the transmitted power, antenna characteristics, target properties, and range.
Analyzing the radar equation helps understand the factors that influence radar system design and performance.
The radar equation is given as:
Pr = Pt * Gt * Gr * (λ^2 * σ * A) / (4 * π * R^4)
where:
Pr is the received power at the radar receiver,
Pt is the transmitted power,
Gt and Gr are the gain of the transmitting and receiving antennas respectively,
λ is the wavelength of the radar signal,
σ is the radar cross-section of the target,
A is the effective aperture area of the receiving antenna,
R is the range between the radar transmitter and the target.
By analyzing the radar equation, we can understand the factors that affect the received power and the design of a radar system. The transmitted power and the gains of the antennas influence the strength of the transmitted and received signals. The wavelength of the radar signal determines the resolution and target detection capabilities. The radar cross-section (σ) represents the reflectivity of the target and its ability to scatter the radar signal. The effective aperture area of the receiving antenna (A) determines the ability to capture and detect the weak reflected signals. The range (R) between the radar and the target affects the received power.
To design a radar system, the radar equation can be used to determine the required transmitted power, antenna characteristics, and sensitivity of the receiver to achieve a desired level of received power. The equation helps in optimizing the antenna gain, choosing the appropriate radar frequency, and considering the target characteristics. By understanding the radar equation and its parameters, engineers can design radar systems with the desired range, resolution, and target detection capabilities while considering factors such as power consumption, signal processing, and environmental conditions.
Learn more about radar frequency here:- brainly.com/question/30504997
#SPJ11
A long straight wire has a current of 18.0 A flowing upwards. An electron is traveling parallel to the wire, in the same direction as the current, and at a speed of 125,000 m/s. If the electron is 15.0 cm from the wire, what is the magnitude and direction of the magnetic force on the moving electron?
Answers
Hence, the magnitude of the magnetic force acting on the electron is 5.12 × 10^-14 N and its direction is in the right-hand direction.
When a current-carrying wire is placed in a magnetic field, it experiences a force. The right-hand rule for magnetic force can be used to determine the direction of the force. When a current-carrying wire is placed in a magnetic field, it experiences a force. The right-hand rule for magnetic force can be used to determine the direction of the force. The direction of the force is perpendicular to both the magnetic field and the current in the wire.
Given:
The current in the wire is 18.0 A flowing upwards.
The electron is traveling parallel to the wire, in the same direction as the current, and at a speed of 125,000 m/s.
The electron is 15.0 cm from the wire.
Force experienced by the electron moving with velocity v and charge q in a magnetic field B is given by the formula:F = q(v×B)
Here, q = -1.6 × 10^-19 C, v = 125,000 m/s, and B is given by B = μ₀I/2πr
μ₀ = 4π×10^-7 Tm/A
The magnitude of magnetic force on the electron is given as:F = (1.6 × 10^-19 C) × (125,000 m/s) × [4π×10^-7 Tm/A × 18.0 A/(2π × 0.15 m)]
F = 5.12 × 10^-14 N
As the direction of the current in the wire is upwards and the electron is traveling parallel to the wire, in the same direction as the current, so the direction of the magnetic force on the electron will be in the right-hand direction.
Hence, the magnitude of the magnetic force acting on the electron is 5.12 × 10^-14 N and its direction is in the right-hand direction.
To know more about magnetic field visit:
https://brainly.com/question/31743819
#SPJ11