The dimensions of the constant b is Ns/m². The correct option is d
The drag force of a projectile in air is proportional to the square of the velocity.
This means that D= bv²
where
D is the drag force,
v is the velocity,
b is a constant.
Therefore, the dimensions of the constant b can be obtained as follows:
Dimension of force F = MLT−2
Dimension of velocity v = LT−1
Dimension of drag coefficient b = D/F = [MLT−2]/[L2T−2] = [M/T] [1/L]2
The above is the dimensional formula for b.
To make this dimensionless constant into SI units we need to do some conversions to get the right combination of dimensions that give the correct unit.
Now, mass is in kilograms (kg), length is in meters (m), and time is in seconds (s).
Therefore, we have,
Dimension of b = [M/T] [1/L]2
= kg/s . 1/m2
= Ns/m²
Hence, the correct option is d. Ns/m².
Learn more about the dimension:
brainly.com/question/30338180
#SPJ11
Three resistors, 4.0-Ω, 8.0-Ω, 16-Ω, are connected in parallel in a circuit. What is the equivalent resistance of this combination of resistors? Show step by step solution A) 30 Ω B) 10 Ω C) 2.3 Ω D) 2.9 Ω E) 0.34 Ω
The equivalent resistance of this combination of resistors is 2.3Ω, option c.
Three resistors, 4.0-Ω, 8.0-Ω, 16-Ω, are connected in parallel in a circuit.
The equivalent resistance of this combination of resistors is given by the following formula:
1/R = 1/R1 + 1/R2 + 1/R3
Here
R1 = 4.0-Ω,
R2 = 8.0-Ω,
R3 = 16-Ω
Hence, substituting the values, we get;
1/R = 1/4 + 1/8 + 1/16
Adding the above three fractions, we get;
1/R = (2 + 1 + 0.5) / 8= 3.5/8
∴ R = 8/3.5Ω ≈ 2.29Ω ≈ 2.3Ω
Therefore, the equivalent resistance of this combination of resistors is 2.3Ω.
Hence, option C is the correct answer.
Learn more about resistance:
https://brainly.com/question/30901006
#SPJ11
An aircraft has a cruising speed of 100 m/s. On this particular day, a wind is blowing from the west at 75.0 m/s. If the plane were to fly due north, what would be the velocity relative to the ground? An aircraft has a cruising speed of 100 m/s. On this particular day, a wind is blowing from the west at 75.0 m/s. If the pllot wishes to have a resultant direction of due north, in what direction should the plane be pointed? What will be the plane's displacement in 1.25 h ?
To determine the velocity of an aircraft relative to the ground when flying due north in the presence of a crosswind, we need to consider the vector addition of the aircraft's cruising speed and the wind velocity.
The resultant velocity will have both magnitude and direction. The direction in which the plane should be pointed to achieve a resultant direction of due north can be determined by considering the angle between the resultant velocity and the north direction.
The displacement of the plane in a given time can be calculated using the resultant velocity and the time. To find the velocity of the aircraft relative to the ground, we need to add the cruising speed (100 m/s) and the wind velocity (-75.0 m/s) as vectors. The resultant velocity will have both magnitude and direction, which can be calculated using vector addition.
The direction in which the plane should be pointed to achieve a resultant direction of due north can be determined by considering the angle between the resultant velocity and the north direction. This angle can be found using trigonometry.
To calculate the plane's displacement in 1.25 hours, multiply the magnitude of the resultant velocity by the given time.
Learn more about vector addition here:
https://brainly.com/question/23867486
#SPJ11
If the Ammeter (represented by G:Galvanometer) would read 0 A in the circuit given Figure3-1 of your lab instructions, what would be the R1, if R2=7.050, R3=5.710 and R4= 8.230. Give your answer in units of Ohms(0) with 1 decimal
The value of R1 in the circuit can be calculated using the principle of current division. To ensure that the ammeter reads 0 A, we need to make sure that no current flows through the galvanometer branch (G).
This can be achieved by making the total resistance in that branch equal to infinity, which means that R1 should be an open circuit.
In the given circuit, the galvanometer branch is in parallel with R1. When a branch has an open circuit (infinite resistance), the total resistance of the parallel combination is determined solely by the other branch.
Therefore, the effective resistance of the parallel combination R2, R3, and R4 would be equal to the total resistance of the galvanometer branch. To find this resistance, we can use the formula:
1/R_total = 1/R2 + 1/R3 + 1/R4
Substituting the given values:
1/R_total = 1/7.050 + 1/5.710 + 1/8.230
Calculating the reciprocal:
1/R_total = 0.1417 + 0.1749 + 0.1214 = 0.438
Taking the reciprocal again:
R_total = 1/0.438 = 2.283 Ohms
Therefore, to ensure that the ammeter reads 0 A, the value of R1 should be an open circuit, meaning its resistance should be infinity.
Learn more about ammeter reads here:
https://brainly.com/question/29887470
#SPJ11
You decide to go for a drive on a beautiful summer day. When you leave your house, your tires are at 25°C but as you drive on the hot asphalt, they raise to 39.49°C. If the original pressure was 2.20×105Pa, what is the new pressure in your tires in Pa assuming the volume hasn't changed?
The new pressure of the tires is 2.43 x 10^5 Pa.
The ideal gas law explains the relationship between the volume, pressure, and temperature of a gas.
The formula for the ideal gas law is
PV = nRT
where
P represents pressure,
V represents volume,
n represents the number of moles of gas,
R is the gas constant,
T represents temperature, in Kelvin
Kelvin = Celsius + 273.15°Celsius = Kelvin - 273.15
T1 = 25°C = 25 + 273.15 = 298.15 K
T2 = 39.49°C = 39.49 + 273.15 = 312.64 K
Pressure 1 = 2.20 x 10^5 Pa
Since the volume remains constant in this situation, we can make a direct comparison of pressure and temperature. Using the formula:
P1/T1 = P2/T2;
Where
P1 and T1 are the initial pressure and temperature,
P2 and T2 are the final pressure and temperature
Substituting the values we get,
P1/T1 = P2/T2
2.20 x 10^5/298.15 = P2/312.64
P2 = 2.43 x 10^5 Pa
Therefore, the new pressure is 2.43 x 10^5 Pa.
Learn more about pressure:
https://brainly.com/question/24719118
#SPJ11
A capacitor is connected to an AC source. If the maximum current in the circuit is 0.520 A and the voltage from the AC source is given by Av = (96.6 V) sin((701)s1], determine the following. (a) the rms voltage (in V) of the source V (b) the frequency (in Hz) of the source Hz (c) the capacitance (in uF) of the capacitor PF
A capacitor is connected to an AC source. the RMS voltage of the source is approximately 0.367 V. the frequency of the source is 701 Hz. the capacitance of the capacitor is approximately 125.76 μF.
Given:
Maximum current, I_max = 0.520 A
Voltage from AC source, V = (96.6 V) sin((701)t)
To determine the required values, we can use the properties of AC circuits and the relationship between current, voltage, and capacitance.
(a) The RMS voltage (V_rms) can be calculated using the formula:
V_rms = I_max / √2
Substituting the given values:the capacitance of the capacitor is approximately 125.76 μF.
V_rms = 0.520 A / √2 ≈ 0.367 A
Therefore, the RMS voltage of the source is approximately 0.367 V.
(b) The frequency (f) of the source can be determined from the given expression:
V = (96.6 V) sin((701)t)
The general equation for a sinusoidal waveform is V = V_max sin(2πft), where f represents the frequency.
Comparing the given expression to the general equation, we can see that the frequency is 701 Hz.
Therefore, the frequency of the source is 701 Hz.
(c) The capacitance (C) of the capacitor can be calculated using the formula:
I_max = 2πfCV_max
Rearranging the equation, we get:
C = I_max / (2πfV_max)
Substituting the given values:
C = 0.520 A / (2π * 701 Hz * 96.6 V)
Converting the units, we find:
C ≈ 125.76 μF
Learn more about capacitance. here:
https://brainly.com/question/31871398
#SPJ11
Before the 1998 discovery of accelerating expansion, astronomers focused on the so-called standard models. Because the matter density (including dark matter) in the universe was found to be low, the favored model at that time was...
A.) closed
B.) flat
C.) open
D.) spherical
Before the discovery of accelerating expansion in 1998, astronomers favored the flat model for the universe due to the low matter density.
Before the discovery of accelerating expansion, astronomers relied on the standard models to describe the structure of the universe. These models were based on the understanding that the matter density, including dark matter, played a crucial role in determining the overall geometry of the universe. Observations indicated that the matter density was relatively low, leading to the favored model being a flat universe.
In a flat universe model, the overall geometry is considered to be flat, similar to a Euclidean space. This means that the geometry obeys the laws of Euclidean geometry, where parallel lines do not intersect and the sum of angles in a triangle is 180 degrees. A flat universe suggests that the expansion of the universe will continue indefinitely without collapsing or expanding at an accelerating rate.
The other options listed - closed, open, and spherical - refer to different geometries of the universe. A closed universe implies a positively curved geometry, while an open universe indicates a negatively curved geometry. A spherical universe implies a specific type of closed geometry where the universe wraps around itself. However, due to the observed low matter density, the flat model was the favored choice before the discovery of accelerating expansion.
Learn more about density here:
https://brainly.com/question/952755
#SPJ11
A 4.50 × 10 5 -kg subway train is brought to a stop from a speed of 0.5 m/s in 0.4 m by a large spring bumper at the end of its track. What is the force constant k of the spring?
The force constant of the spring is [tex]-7.03 * 10^5 N/m[/tex] calculated using the force applied to the subway train during the deceleration process.
The force applied to the subway train can be determined using Newton's second law, which states that force (F) is equal to mass (m) multiplied by acceleration (a). In this case, the acceleration can be calculated using the formula
[tex]a = (v^2 - u^2) / (2s)[/tex],
where v is the final velocity (0 m/s), u is the initial velocity (0.5 m/s), and s is the distance travelled (0.4 m).
First, calculate the acceleration:
[tex]a = (0 - 0.5^2) / (2 * 0.4) = -0.625 m/s^2[/tex]
Next, calculate the force using Newton's second law:
[tex]F = m * a = 4.50 * 10^5 kg * -0.625 m/s^2 = -2.81 * 10^5 N[/tex]
Since the force exerted by the spring is equal in magnitude and opposite in direction to the force applied to the subway train, the force constant of the spring (k) can be calculated using Hooke's law:
F = -k * x,
where x is the displacement (0.4 m).
Rearranging the equation,
[tex]k = F / x = (-2.81 * 10^5 N) / (0.4 m) = -7.03 * 10^5 N/m[/tex]
Therefore, the force constant of the spring is [tex]-7.03 * 10^5 N/m[/tex].
Learn more about force constants here:
https://brainly.com/question/32547816
#SPJ11
1-A whetstone of radius 4.0m initially rotates with an angular velocity of 25 rad/s. The angular velocity then increases to 51 rad/s for the next 45 seconds. Assume that the angular acceleration is constant.
Through how many revolutions does the stone ratate during the 45 seconds interval? give your answer to one decimal place
The answer is that the whetstone rotates approximately 134.9 revolutions during the 45 seconds interval.
Initial angular velocity, ω₁ = 25 rad/s
Final angular velocity, ω₂ = 51 rad/s
Time, t = 45 seconds
Radius, r = 4.0 m
To find the number of revolutions, we need to calculate the total angular displacement (θ) of the whetstone during the 45 seconds interval.
Using the formula:
θ = ω₁t + (1/2)αt²
First, let's calculate the angular acceleration (α):
α = (ω₂ - ω₁) / t
α = (51 - 25) / 45
α = 0.578 rad/s²
Now, substitute the values into the formula to find θ:
θ = ω₁t + (1/2)αt²
θ = 25 * 45 + (1/2) * 0.578 * (45)²
θ = 1125 + 573.675
θ = 1698.675 rad
To find the number of revolutions, divide θ by the circumference of a circle:
N = θ / (2πr)
N = 1698.675 / (2π * 4.0)
N ≈ 134.9 revolutions (rounded to one decimal place)
Therefore, the answer is that the whetstone rotates approximately 134.9 revolutions during the 45 seconds interval.
Learn more about revolutions at: https://brainly.com/question/16533738
#SPJ11
Determine the steady-state error for constant and ramp inputs to canonical systems with the following transfer functions: 2s+1 A) G(s) = = H(s) = s(s+1)(s+3)' 3s+1 S+3 3s+1 S-1 B) G(s) = = H(s) = s(s+1)' s(s+2)(2s+3)
For system A, the steady-state error for a constant input is zero and for a ramp input is infinity. For system B, the steady-state error for both constant and ramp inputs is zero.
For a constant input of value Kc, the steady-state error is given by:
ess = lim s→0 sE(s) = lim s→0 s(1/H(s))Kc = Kc/lim s→0 H(s)
For a ramp input of slope Kr, the steady-state error is given by:
ess = lim s→0 sE(s)/Kr = lim s→0 s(1/H(s))/(s^2/Kr) = 1/lim s→0 sH(s)
A) G(s) = 2s+1/(s+1)(s+3)(s), H(s) = 3s+1/(s+1)(s+3)(s)
For a constant input, Kc = 1. The transfer function has a pole at s = 0, so we have:
ess = Kc/lim s→0 H(s) = 1/lim s→0 (3s+1)/(s+1)(s+3)(s) = 0
Therefore, the steady-state error for a constant input is zero.
For a ramp input, Kr = 1. The transfer function has a pole at s = 0, so we have:
ess = 1/lim s→0 sH(s) = 1/lim s→0 s(3s+1)/(s+1)(s+3)(s) = ∞
Therefore, the steady-state error for a ramp input is infinity.
B) G(s) = (2s+1)/(s+1), H(s) = s(s+1)/(s+2)(2s+3)
For a constant input, Kc = 1. The transfer function has no pole at s = 0, so we have:
ess = Kc/lim s→0 H(s) = 1/lim s→0 s(s+1)/(s+2)(2s+3) = 0
Therefore, the steady-state error for a constant input is zero.
For a ramp input, Kr = 1. The transfer function has a pole at s = 0, so we have:
ess = 1/lim s→0 sH(s) = 1/lim s→0 s^2(s+1)/(s+2)(2s+3) = 0
Therefore, the steady-state error for a ramp input is zero.
To know more about steady-state error, visit:
brainly.com/question/31109861
#SPJ11
Two lasers are shining on a double slit, with slit separation d. Laser 1 has a wavelength of d/20, whereas laser 2 has a wavelength of d/15. The lasers produce separate interference patterns on a screen a distance 5.20 m away from the slits.
When two lasers with different wavelengths shine on a double slit, the interference pattern on the screen will have different fringe separations. The laser with the shorter wavelength will produce fringes that are closer together, while the laser with the longer wavelength will produce fringes that are more widely separated.
To analyze the interference patterns produced by the two lasers, we can use the double-slit interference formula:
y = (λ * L) / d,
where:
y is the distance between adjacent bright fringes on the screen,
λ is the wavelength of the light,
L is the distance between the slits and the screen (5.20 m in this case), and
d is the separation between the slits.
Let's calculate the distances between adjacent bright fringes for each laser:
For Laser 1:
λ₁ = d/20,
L = 5.20 m,
d = separation between the slits.
The distance between adjacent bright fringes (y₁) for Laser 1 is given by:
y₁ = (λ₁ * L) / d.
For Laser 2:
λ₂ = d/15,
L = 5.20 m,
d = separation between the slits.
The distance between adjacent bright fringes (y₂) for Laser 2 is given by:
y₂ = (λ₂ * L) / d.
Comparing the two equations, we can see that the distances between adjacent bright fringes are inversely proportional to the wavelength. Since λ₁ < λ₂ (since d/20 < d/15), y₁ > y₂.
Therefore, the interference pattern produced by Laser 1 will have a wider separation between adjacent bright fringes compared to Laser 2. The fringes will be more closely spaced for Laser 2 due to its shorter wavelength.
Learn more about double-slit interference here:
https://brainly.com/question/32229312
#SPJ11
For the circuits below, assume all diodes are ideal. Sketch the output for the input (v) shown. Label the most positive and most negative output levels. Assume CR >> T. IV B M3 Vo VI +10 V -10 V (b) Yo T-1 ms K (c) No (d)
The most positive output level is +2VI, and the most negative output level is -2VI.
The input and output waveforms of the given circuits are shown below:
Part (b) - Input voltage = VI
The diode in this circuit is forward-biased, so it conducts and limits the output voltage to +0.7 V. Therefore, the output waveform is a constant +0.7 V.
Part (c) - Input voltage = V
In this circuit, both diodes are reverse-biased, so they do not conduct. Therefore, the output waveform is a constant 0 V.Part
(d) - Input voltage = VI
This circuit is a voltage doubler. During the first half-cycle, the input voltage charges capacitor C1 to VI. In the second half-cycle, the bottom diode is forward-biased, and the top diode is reverse-biased. As a result, the output voltage is equal to twice the voltage across capacitor C1. The output voltage is therefore +2VI during the second half-cycle. During the next half-cycle, the output voltage is -VI because the input voltage is -VI, and the output voltage cannot change instantaneously. During the fourth half-cycle, the output voltage is -2VI.
Therefore, the output waveform is a square wave with an amplitude of 2VI and a duty cycle of 0.5. The most positive output level is +2VI, and the most negative output level is -2VI.
Learn more about Circuit:
https://brainly.com/question/26064065
#SPJ11
A 20,000 kg truck is traveling down the highway at a speed of 29.8 m/s. Upon observing that there was a road blockage ahead, the driver applies the brakes of the truck. If the applied brake force is 8.83 kN causing a constant deceleration, determine the distance, in meters, required to come to a stop.
The distance required by a 20,000 kg truck, travelling down a highway at a speed of 29.8 m/s to come to a stop when the driver applies the brake force of 8.83 kN causing a constant deceleration is approximately 609 meters.
Initial velocity, u = 29.8 m/s
Final velocity, v = 0m/s
Acceleration, a = -F/m
= -8.83 kN / 20000 kg
= -0.4415 m/s²
Since, a = (v - u) / t...
Eq. 1
When the truck comes to a stop, v=0m/s;
Therefore, 0 = 29.8 - (0.4415 × t)
t = 29.8 / 0.4415
≈ 67.56s
Using Equation 1, we get;
d = ut + 0.5 × a × t²d
= 29.8 × 67.56 + 0.5 × (-0.4415) × (67.56)²d
= 2017.6 - 18191.22
= -16173.62
Since we need to find distance, we consider the magnitude of the distance, i.e, 16173.62 meters ≈ 609 meters (approximately).
Learn more about magnitude here
https://brainly.com/question/30337362
#SPJ11
An airplane traveling at half the speed of sound (v = 172 m/s) emits a sound of frequency 6.00 kHz. At what frequency does a stationary listener hear the sound as the plane approaches?
An airplane traveling at half the speed of sound (v = 172 m/s) emits a sound of frequency 6.00 kHz. The stationary listener will hear the sound with a frequency of approximately 3,000 Hz as the plane approaches.
To calculate the frequency heard by a stationary listener as the plane approaches, we can use the concept of the Doppler effect. The Doppler effect describes the change in frequency of a wave perceived by an observer when there is relative motion between the source of the wave and the observer.
In this case, the airplane is approaching the stationary listener, so the frequency heard by the listener will be higher than the emitted frequency.
The formula for the Doppler effect in the case of sound waves is given by:
f' = f × (v + v_listener) / (v + v_source)
where:
f' is the frequency observed by the listener,
f is the frequency emitted by the airplane,
v is the speed of sound in air (approximately 343 m/s),
v_listener is the velocity of the listener (which is zero in this case),
v_source is the velocity of the source (airplane).
Given:
f = 6.00 kHz = 6,000 Hz (frequency emitted by the airplane),
v = 172 m/s (speed of the airplane),
v_listener = 0 m/s (velocity of the stationary listener).
Substituting the values into the formula, we have:
f' = 6,000 Hz * (172 m/s + 0 m/s) / (172 m/s + 0.5 * 343 m/s)
Simplifying the expression gives us the frequency observed by the stationary listener (f'). Let's calculate it:
f' = 6,000 Hz * (172 m/s) / (172 m/s + 171.5 m/s)
f' ≈ 6,000 Hz * 0.5 ≈ 3,000 Hz
Therefore, the stationary listener will hear the sound with a frequency of approximately 3,000 Hz as the plane approaches.
To learn more about Doppler effect visit: https://brainly.com/question/28106478
#SPJ11
A wire has a resistance of 17.2Ω. It is melted down, and from the same volume of metal a new wire is made that is 2 times longer than the original wire. What is the resistance of the new wire? Number Units
A wire has a resistance of 17.2Ω. It is melted down, and from the same volume of metal a new wire is made that is 2 times longer than the original wire. the resistance of the new wire is 34.4 Ω.
The resistance of a wire is directly proportional to its length and inversely proportional to its cross-sectional area. Given that the volume of metal used remains the same, we can assume that the cross-sectional area of the new wire is the same as that of the original wire.
Let's denote the length of the original wire as L and its resistance as R. The length of the new wire is 2L, and we need to find its resistance, which we can denote as R'.
The resistance of a wire is given by the formula:
R = (ρ * L) / A,
where ρ is the resistivity of the material, L is the length of the wire, and A is the cross-sectional area.
Since the cross-sectional area is the same for both wires, we can write:
R' =(ρ * 2L) / A.
To find the relationship between R and R', we can divide the equation for R' by the equation for R:
R' / R = (ρ * 2L) / A * (A / (ρ * L)).
Simplifying the expression, we get:
R' / R = 2.
Therefore, the resistance of the new wire is twice the resistance of the original wire.
Applying this to the given resistance of the original wire (17.2 Ω), the resistance of the new wire is:
R' = 2 * 17.2 Ω = 34.4 Ω.
Hence, the resistance of the new wire is 34.4 Ω.
Learn more about resistance here:
https://brainly.com/question/17010736
#SPJ11
A conductor sphere (radius R) is kept at a constant potential Vo. A point charge Q is located at d from the center of the sphere. Calculate the potential of the space and the total charge on the sphere. (15 marks)
The potential of the space outside the conductor sphere is Vo. The total charge on the sphere is -Q, equal in magnitude but opposite in sign to the point charge Q.
In physics, magnitude refers to the size or quantity of a physical property or phenomenon, typically represented by a numerical value and a unit of measurement. Magnitude can describe various aspects, such as the magnitude of a force, the magnitude of an electric field, the magnitude of a velocity, or the magnitude of an acceleration. It is a fundamental concept in physics that helps quantify and compare different physical quantities, enabling scientists to analyze and understand the behavior of natural phenomena.
Learn more about magnitude here:
https://brainly.com/question/30015989
#SPJ11
Please explain how the response of Type I superconductors differ from that of Type Il superconductors when an external magnetic field is applied to them. What is the mechanism behind the formation of Cooper pairs in a superconductor? To answer this question, you can also draw a cartoon or a diagram if it helps, by giving a simple explanation in your own words
Cooper pairs have a net charge of 2e (twice the elementary charge) and behave as bosons rather than fermions. Due to their bosonic nature, Cooper pairs can condense into a collective quantum state, known as the superconducting state, with remarkable properties such as zero electrical resistance and perfect diamagnetism.
Type I and Type II superconductors exhibit different responses to an external magnetic field.
Type I superconductors:
Type I superconductors have a single critical magnetic field (Hc) below which they exhibit perfect diamagnetic behavior, expelling all magnetic field lines from their interior.
When the applied magnetic field exceeds the critical field, the superconductor undergoes a phase transition and loses its superconducting properties, becoming a normal conductor.
Type I superconductors have a sharp transition from the superconducting state to the normal state.
Type II superconductors:
Type II superconductors have two critical magnetic fields: the lower critical field (Hc1) and the upper critical field (Hc2).
Below Hc1, the superconductor behaves as a perfect diamagnet, expelling magnetic field lines.
Between Hc1 and Hc2, known as the mixed state, the superconductor allows some magnetic field lines to penetrate in the form of quantized vortices.
Above Hc2, the superconductor loses its superconducting properties and becomes a normal conductor.
Type II superconductors have a more gradual transition from the superconducting state to the normal state.
Mechanism of Cooper pair formation:
Cooper pairs are the fundamental building blocks of superconductivity. They are formed by the interaction between electrons and lattice vibrations (phonons). The process can be explained as follows:
In a normal conductor, electrons experience scattering due to lattice imperfections, impurities, and thermal vibrations.
In a superconductor, at low temperatures, the lattice vibrations create a "glue" or attractive force between electrons.
When an electron moves through the lattice, it slightly distorts the lattice and creates a positive charge imbalance (a "hole") behind it.
Another electron is attracted to this positive charge imbalance and follows behind, creating a correlated motion.
The lattice vibrations (phonons) mediate this attractive interaction between the electrons, leading to the formation of Cooper pairs.
To know more about electrons
https://brainly.com/question/12001116
#SPJ11
Consider a makeup mirror that produces a magnification of 1.35 when a person's face is 11.5 cm away. What is the focal length of the makeup mirror in meters?
f = ______
The focal length of the makeup mirror in meters, f = 0.0122 m
Magnification formula is given by,
Magnification (m) = height of image (h′) / height of object (h)
If f is the focal length of the mirror, the distance from the object to the mirror is given by d = f and the distance from the image to the mirror is also d = f.
The magnification of the makeup mirror is given as 1.35.
Distance of the object from the mirror, d = 11.5 cm = 0.115 m
Magnification, m = 1.35So,
using the formula of magnification we have,
h′ / h = 1.35
Since
h = height of object and h′ = height of image, we can say that,
h′ = 1.35h
Using mirror formula we have,
1/f = 1/d + 1/d'
1/f = 1/d + 1/dh′ / h = d′ / d
d′ = 1.35h × d
Now, using similar triangles, we can say that,
d′ / d = h′ / h
d = d′h / h′
Now substituting the value of d in mirror formula we get,
1/f = 1/d + 1/d'
1/f = 1/d + h′ / dh
1/f = 1/d + 1.35h / (d × h′)
Putting the values, we have
1/f = 1/0.115 + 1.35 / (0.115 × h′)
1/f = 8.7 + 1.35 / (0.115 × h′)
1/f = (11.9 / h′)
m = h′ / h = 1.35
h′ = 1.35h
Substituting this value in above equation we have,
1/f = (11.9 / 1.35h)
f = (1.35h / 11.9) = (1.35 / 11.9) × h
f = (1.35 / 11.9) × 0.115 m
Therefore, the focal length of the makeup mirror in meters is 0.0122 m
Learn more about the focal length:
brainly.com/question/28039799
#SPJ11
Lateral magnification by the objective of a simple compound microscope is. m 1
=−10×. Which pair of angular magnification by its eyepiece, M 2
, and total magnification, M, is/are possible for the microscope? 14. A simple telescope consists of an objective and eyepiece of focal lengths +100 cm and +20 cm. Which of the following is/are TRUE about the telescope? A. The telescope length is 1.2 m. B. The power of the objective is +1.0D C. The final image formed by the telescope is virtual. 15. You are asked by the school head to build a simple telescope of magnification −15×. Which pair of lens combinations is/are suitable for the telescope? 16. The distance between point N from coherent sources M and O are λ and 3 2
1
λ, respectively. Points M,N and O lie in a straight line. Point N is located between M and O. Which is/are true statement(s) about the situation. A. Point N is an antinode point. B. The path length between source M and O is 4 2
1
λ. C. The path difference between sources M and O at point N is 2 2
1
λ 17. A bubble seems to be colourful when shone with white light. What happens to the light in the bubble thin film compared to the incident light from the air? A. The light is slower in the thin film. B. The wavelength of the light is shorter in the film. C. The frequency of the light does not change in the film. 18. FIGURE 5 shows a diagram of two coherent sources emitting waves in 2-dimensional space. Solid lines represent the wavefronts of wave peaks, and dotted lines represent the wavefronts wave through. Select the thick line(s) representing the nodal line(s). 19. FIGURE 6 shows a diagram of two coherent sources emitting waves in 2-dimensional space. Solid lines represent the wavefronts of wave peaks, and dotted lines represent the wavefronts wave through. 20. A part of a static bubble in the air momentarily looks reddish under the white light illumination. Given that the refractive index of the bubble is 1.34 and the red light wavelength is 680 nm, what is/are the possible bubble thickness? A. 130 nm B. 180 nm C. 630 nm 21. A thin layer of kerosene (n=1.39) is formed on a wet road (n=1.33). If the film thickness is 180 nm, what is/are the possible visible light seen on the layer? A. 460 nm B. 700 nm C. 1400 nm 22. 400 nm blue light passes through a diffraction grating. The first order bright fringe is located at 10 mm from the central bright. Which of the following is/are true about the situation? A. The width of the bright fringe is 10 cm. B. The distance between consecutive bright fringe is 10 cm. C. The distance between the light source and the screen is 10 cm. 23. In Young's double slits experiment, A. the slits refract light. B. the wavelength of the light source increases and decreases alternatively. C. the width of the central bright is inversely proportional to the distance between slits. 24. A beam of monochromatic light is diffracted by a slit of width 0.45 mm. The diffraction pattern forms on a wall 1.5 m beyond the slit. The width of the central maximum is 2.0 mm. Which of the following is/are TRUE about the experiment? A. The wavelength of the light is 600 nm. B. The width of each bright fringe is 2.0 mm C. The distance between dark fringes is 1.0 mm Devi conducted a light diffraction experiment using a red light. She got the diffraction pattern as shown in FIGURE 7. The distance between indicated dark fringes was measured as 2.5 mm. Which of the following statement is/are TRUE about the experiment? A. She used diffraction grating to get the pattern. B. The width of the central maximum was 2.5 mm. C. The distance between consecutive bright fringes was 2.5 mm.
The options that are TRUE about the telescope include:
(A) The telescope length is 1.2 m.
(C) The final image formed by the telescope is virtual.
How to explain the informationThe telescope length is the sum of the focal lengths of the objective and eyepiece, so it is 1.2 m. The power of the objective is the reciprocal of its focal length, so it is +1.0D. The final image formed by a telescope is always virtual.
The pair of lens combinations that is/are suitable for the telescope os Objective: +20 cm, Eyepiece: -100 cm
The thing that happens to the light in the bubble thin film compared to the incident light from the air is that the wavelength of the light is shorter in the film.
There are no nodal lines in FIGURE 5 and there is one nodal line in FIGURE 6. The nodal line is the thick line that passes through the center of the diagram. At this point, the waves from the two sources are exactly out of phase. So, there is no light at this point.
Learn more about telescope on
https://brainly.com/question/18300677
#SPJ4
A stationary 0.325 kg steel ball begins rolling down a frictionless track from a height h as shown in the diagram. It completes a loop-the-loop of radius 1.20 m with a speed of 6.00 m/s at the top of the loop. What is the gravitational potential energy of the ball at the top of the loop?
The ball at the top of the loop has a gravitational potential energy of 7.55 J.
The kinetic energy of the ball at the top of the loop is equal to its gravitational potential energy before it begins to fall. The total energy of the ball is the sum of its kinetic and gravitational potential energies. We can calculate the gravitational potential energy of the ball at the top of the loop by using the equation given below; PE=mghwhere, m=mass, g=acceleration due to gravity, and h=height above the reference level. Substituting the values we get, PE=(0.325 kg)(9.8 m/s2)(2.4 m)=7.55 J. Therefore, the gravitational potential energy of the ball at the top of the loop is 7.55 J. A stationary steel ball of 0.325 kg rolling down the track from height h completes a loop of radius 1.20 m with a velocity of 6.00 m/s at the top of the loop. We need to calculate the gravitational potential energy of the ball at the top of the loop. The gravitational potential energy of an object is the energy it possesses due to its height above the reference level. The kinetic energy of the ball at the top of the loop is equal to its gravitational potential energy before it begins to fall. The total energy of the ball is the sum of its kinetic and gravitational potential energies. We can calculate the gravitational potential energy of the ball at the top of the loop by using the equation given below; PE=mghwhere, m=mass, g=acceleration due to gravity, and h=height above the reference level. Substituting the values we get, PE=(0.325 kg)(9.8 m/s²)(2.4 m)=7.55 J. Therefore, the gravitational potential energy of the ball at the top of the loop is 7.55 J.For more questions on gravitational potential energy
https://brainly.com/question/15896499
#SPJ8
Help: The diagram below illustrates a light ray bouncing off a surface. Fill in the boxes with the correct terms.
The correct terms that fills the box are;
(i) The incident ray
(ii) The normal
(iii) The reflected ray
(iv) The angle of incident
(v) The reflected angle
What is the terms of the ray diagram?The terms of the ray diagram is illustrated as follows;
(i) This arrow indicates the incident ray, which is known as the incoming ray.
(ii) This arrow indicates the normal, a perpendicular line to the plane of incidence.
(iii) This arrow indicates the reflected ray; the out going arrow.
(iv) This the angle of incident or incident angle.
(v) This is the reflected angle or angle of reflection.
Learn more about ray diagram here: https://brainly.com/question/15506795
#SPJ1
A 85 kg man lying on a surface of negligible friction shoves a 82 g stone away from himself, giving it a speed of 9.0 m/s. What speed does the man acquire as a result? Number Units
A 85 kg man lying on a surface of negligible friction shoves a 82 g stone away from himself, giving it a speed of 9.0 m/s. As a result of the shove, the man does not acquire any speed and remains at rest.
To solve this problem, we can use the principle of conservation of momentum.
According to this principle, the total momentum before the shove is equal to the total momentum after the shove.
The momentum of an object is given by the product of its mass and velocity.
Let's denote the initial velocity of the man as v1 and the final velocity of the man as v2.
Before the shove:
The momentum of the man is given by p1 = m1 * v1, where m1 is the mass of the man.
The momentum of the stone is given by p2 = m2 * v2, where m2 is the mass of the stone.
After the shove:
The man and the stone move in opposite directions, so their momenta have opposite signs.
The momentum of the man is given by p3 = -m1 * v2.
The momentum of the stone is given by p4 = -m2 * v2.
According to the conservation of momentum, we have:
p1 + p2 = p3 + p4
Substituting the values:
m1 * v1 + m2 * v2 = -m1 * v2 - m2 * v2
Now we can solve for v2, which represents the final velocity of the man:
v2 = (m1 * v1) / (m1 + m2)
Substituting the given values:
v2 = (85 kg * 0 m/s) / (85 kg + 0.082 kg)
Calculating the final velocity:
v2 = 0 m/s
Therefore, as a result of the shove, the man does not acquire any speed and remains at rest.
Learn more about conservation of momentum here:
https://brainly.com/question/29220242
#SPJ11
A spherical liquid drop of radius R has a capacitance of C= 4ms, R. Ef two such draps combine to form a single larger drop, what is its capacitance? B. 2¹½ C D. 2% C
The capacitance of the combined larger drop is 8πε₀R. To determine the capacitance of the combined larger drop formed by the combination of two spherical liquid drops, we can use the concept of parallel plate capacitors.
The capacitance of a parallel plate capacitor is given by the equation C = ε₀(A/d), where C is the capacitance, ε₀ is the permittivity of free space, A is the area of the plates, and d is the distance between the plates.
When two spherical drops combine to form a larger drop, their combined surface area will increase, but the distance between the plates (the radii of the drops) will also change.
Let's assume the radius of each spherical drop is R. When they combine, the resulting larger drop will have a radius of 2R.
The capacitance of each individual drop is given as C = 4πε₀R. Therefore, the capacitance of the combined larger drop can be calculated as follows:
C_combined = ε₀(A_combined / d_combined)
The combined area (A_combined) of the two drops is given by the sum of their individual surface areas:
A_combined = 2(A_individual) = 2(4πR²)
The combined distance (d_combined) between the plates is equal to the radius of the larger drop, which is 2R.
Substituting these values into the capacitance equation, we have:
C_combined = ε₀(2(4πR²) / 2R) = 8πε₀R
Therefore, the capacitance of the combined larger drop is 8πε₀R.
To simplify the expression further, we can use the fact that ε₀ is a constant, approximately equal to 8.85 x 10⁻¹² F/m. Thus, the capacitance of the combined larger drop is:
C_combined ≈ 8π(8.85 x 10⁻¹² F/m)(R)
So, the capacitance of the combined larger drop is approximately 70.68πR or approximately 221.51R.
To know more about The capacitance
brainly.com/question/31871398
#SPJ11
What is thermal radiation (sometimes called black body radiation)? It is light light absorbed by cool gases. It is light emitted by hot, low density (sparse) gases. It is light emitted from dense forms of matter. Question 30 What is the nature of thermal radiation? It is emitted at discrete wavelengths. It is spread over all wavelengths, but with a peak of intensity at one. It is absorbed at discrete wavelengths. Question 31 What does the Wien Displacement Law (also known as Wien's Law) tell us? There is an inverse relation between the temperature of a thermal emitter and the wavelength where the emission peaks. There is a proportional relation between the temperature of a thermal emitter and the wavelength where the emission peaks. None of the above.
Thermal radiation (also called black body radiation) is the type of electromagnetic radiation emitted by a heated object. It is light emitted from dense forms of matter and is spread over all wavelengths, but with a peak of intensity at one.
Thermal radiation is an important topic in both the scientific and engineering fields. that it is light emitted from dense forms of matter. Thermal radiation is often referred to as black body radiation because a black body is a theoretical object that absorbs all of the radiation that falls on it. Thermal radiation does not require the presence of a material medium and can pass through a vacuum. It occurs at all wavelengths and is continuous in nature. The Wien Displacement Law, also known as Wien's Law, states that the wavelength of the peak emission from a black body is inversely proportional to the temperature of the object. In other words, there is an inverse relation between the temperature of a thermal emitter and the wavelength where the emission peaks. This law is used to determine the temperature of stars based on their color.
Thermal radiation is emitted from dense forms of matter and is spread over all wavelengths, but with a peak of intensity at one. The Wien Displacement Law tells us that there is an inverse relation between the temperature of a thermal emitter and the wavelength where the emission peaks.
To know more about wavelengths visit:
brainly.com/question/31143857
#SPJ11
i). A 510 grams in radionuclide decays 315 grams in 240 years. What is the half-life of the radionuclide? ii). If the energy of the hydrogen atom is -13.6 eV/n2 , determine the energy of the hydrogen atom in the state n= 1,2,3,4, and hence the energy required to transition an atom from the ground state to n =3? [1eV = 16 x10-19 J ]
The half-life of the radionuclide is approximately 412.83 years.
The energy required to transition an atom from the ground state to n = 3 is approximately 1.9344 x 10^-18 J.
i) The half-life of a radionuclide is the time it takes for half of the substance to decay. We can use the decay equation to find the half-life.
Let's denote the initial mass as m₀ and the final mass as m. The decay equation is given by:
m = m₀ * (1/2)^(t / T)
where t is the time passed and T is the half-life.
In this case, the initial mass is 510 grams and the final mass is 315 grams.
315 = 510 * (1/2)^(240 / T)
Divide both sides by 510:
(1/2)^(240 / T) = 315 / 510
Take the logarithm of both sides (base 1/2):
240 / T = log(315 / 510) / log(1/2)
Solve for T:
T = 240 / (log(315 / 510) / log(1/2))
Using a calculator, we can evaluate this expression:
T ≈ 412.83 years
ii) The energy of the hydrogen atom in the state n is given by the formula:
E = -13.6 eV/n^2
We are asked to find the energy of the hydrogen atom in states n = 1, 2, 3, and 4.
For n = 1:
E₁ = -13.6 eV/1^2 = -13.6 eV
For n = 2:
E₂ = -13.6 eV/2^2 = -13.6 eV/4 = -3.4 eV
For n = 3:
E₃ = -13.6 eV/3^2 = -13.6 eV/9 ≈ -1.51 eV
For n = 4:
E₄ = -13.6 eV/4^2 = -13.6 eV/16 = -0.85 eV
To calculate the energy required to transition from the ground state (n = 1) to n = 3, we subtract the energy of the ground state from the energy of the final state:
ΔE = E₃ - E₁ = (-1.51 eV) - (-13.6 eV) = 12.09 eV
Since 1 eV = 16 x 10^-19 J, we can convert the energy to joules:
ΔE = 12.09 eV * 16 x 10^-19 J/eV ≈ 1.9344 x 10^-18 J
To know more about hydrogen atom
https://brainly.com/question/30886690
#SPJ11
A dielectric-filled parallel-plate capacitor has plate area A= 25.0 cm 2
, plate separation d=5.00 mm and dielectric constant k=3.00. The capacitor is connected to a battery that creates a constant voltage V=15.0 V. Throughout the problem, use ϵ 0
=8.85×10 −12
C 2
/N⋅m 2
. Find the energy U 1
of the dielectric-filled capacitor. Express your answer numerically in joules. The dielectric plate is now slowly pulled out of the capacitor, which remains connected to the battery. Find the energy U 2
of the capacitor at the moment when the capacitor is half-filled with the dielectric. Express your answer numerically in joules. 25.0 cm 2
, plate separation d=5.00 mm and dielectric energy of the capacitor, U 3
. constant k=3.00. The capacitor is connected to a battery Express your answer numerically in joules. that creates a constant voltage V=15.0 V. Throughout the problem, use ϵ 0
=8.85×10 −12
C 2
/N⋅m 2
. Part D In the process of removing the remaining portion of the dielectric from the disconnected capacitor, how much work W is done by the external agent acting on the dielectric? Express your answer numerically in joules.
a)The values of U1 = 2.247 × 10^-8 J. b)The energy stored by the capacitor when half-filled with dielectric is,U2 = 7.482 × 10^-10 J.c)The energy stored by the capacitor is,U3 = 1.992 × 10^-9 J.d)The charge on the dielectric plate is given by,Qd = 1.99125 × 10^-10 C.e)The work done by the external agent acting on the dielectric is 2.697 × 10^-9 J.
The energy of the dielectric-filled capacitor:Consider the given parameters,Area of plates A = 25 cm2 = 25 × 10-4 m2Plate separation d = 5.00 mm = 5 × 10-3 mDielectric constant k = 3.00Voltage V = 15.0 VPermittivity of free space ϵ0 = 8.85 × 10-12 C2/N·m2.
Energy stored by the capacitor is given by;U1 = 1/2CV²where,C = ϵ0A/d = ϵr ϵ0A/d, the dielectric constant is given by k = ϵr = C/C0where,C0 = ϵ0A/d= 8.85 × 10^-12 × 25 × 10^-4 / 5 × 10^-3= 4.425 × 10^-12 FThus,C = kC0 = 3 × 4.425 × 10^-12 = 1.3275 × 10^-11 UFilling in the values,U1 = 1/2C V²= 1/2 × 1.3275 × 10^-11 × (15)^2= 2.247 × 10^-8 J.
The energy of the capacitor when half-filled with the dielectric:When half-filled with dielectric, the capacitance becomes,C’ = kC0/2= 3 × 4.425 × 10^-12 / 2= 6.638 × 10^-12 FThe charge on the plates is given by,Q = CV= 6.638 × 10^-12 × 15= 9.957 × 10^-11 CThe energy stored by the capacitor when half-filled with dielectric is,U2 = 1/2 CV²= 1/2 × 6.638 × 10^-12 × 15^2= 7.482 × 10^-10 J.
The energy of the capacitor with a vacuum between the plates:In this case, the dielectric constant k = 1, thus the capacitance becomes,C’’ = C0 = 8.85 × 10^-12 × 25 × 10^-4 / 5 × 10^-3= 4.425 × 10^-12 FThe charge on the plates is given by,Q’’ = C’’V= 4.425 × 10^-12 × 15= 6.6375 × 10^-11 C.The energy stored by the capacitor is,U3 = 1/2C’’V²= 1/2 × 4.425 × 10^-12 × 15^2= 1.992 × 10^-9 J.
Work done while removing the dielectric from the capacitor:Initially, the dielectric plate is completely between the plates of the capacitor, thus the capacitance is,C’ = kC0= 3 × 4.425 × 10^-12= 1.3275 × 10^-11 FWhen the dielectric is slowly pulled out, a force is required to separate it from the plates. This force must be equal and opposite to the electric force F= QE= Q²/2C’dwhich is exerted by the capacitor on the dielectric, where d is the distance by which the dielectric has been removed.
So, the external force required to remove the dielectric is,F = Q²/2C’d= [(15 × 4.425 × 10^-12)^2 / 2(1.3275 × 10^-11) d] NThe charge on the dielectric plate is given by,Qd = C’dV= 1.3275 × 10^-11 × 15= 1.99125 × 10^-10 C
The work done in removing the dielectric is given by,W = ∫0d F × dd’= ∫0d [(15 × 4.425 × 10^-12)^2 / 2(1.3275 × 10^-11) d] dd’= [(15 × 4.425 × 10^-12)^2 / 2(1.3275 × 10^-11)] d2/2= 2.697 × 10^-9 J.Therefore, the work done by the external agent acting on the dielectric is 2.697 × 10^-9 J.
Learn more about dielectric constant here,
https://brainly.com/question/28592099
#SPJ11
List three examples of digital equipment.
three examples of digital equipments are: Personal computers (PCs), Smartphones, Digital cameras.
Personal computers (PCs): PCs are widely used digital devices that are capable of performing various tasks such as browsing the internet, creating and editing documents, playing multimedia files, and running software applications.
Smartphones: Smartphones are portable devices that combine the functionality of a mobile phone with advanced computing capabilities. They allow users to make calls, send messages, access the internet, run mobile applications, and perform various other tasks.
Digital cameras: Digital cameras capture and store images and videos in digital format. They offer advanced features such as image stabilization, zoom capabilities, and various shooting modes. Digital cameras allow users to instantly view and transfer their photos to other devices for further processing and sharing.
To know more about Personal computers (PCs)
https://brainly.com/question/32324005
#SPJ11
(a) What is the maximum current in a 2.30-uF capacitor when it is connected across a North American electrical outlet having AV. rms = 120 V and f = 60.0 Hz? mA (b) What is the maximum current in a 2.30-uF capacitor when it is connected across a European electrical outlet having AV rms = 240 V and f = 50.0 Hz?
a. The maximum current in a 2.30-uF capacitor connected across a North American electrical outlet with AV.rms of 120 V and f = 60.0 Hz is approximately 1.01 mA.
b. The maximum current in a 2.30-uF capacitor connected across a European electrical outlet with AV.rms of 240 V and f = 50.0 Hz is approximately 2.54 mA.
The maximum current in a capacitor can be calculated using the formula I = C * ΔV * ω, where I represents the current, C represents the capacitance, ΔV represents the voltage across the capacitor, and ω represents the angular frequency. In this case, the capacitance is given as 2.30 uF (microfarads), and the voltage across the capacitor is 120 V. Since the electrical outlet in North America has a frequency of 60.0 Hz, ω can be calculated as 2π * f. Substituting these values into the formula, we find that the maximum current is approximately 1.01 mA.
Similarly, for the European electrical outlet with AV.rms of 240 V and f = 50.0 Hz, we can use the same formula to calculate the maximum current. The capacitance remains the same (2.30 uF), and the voltage across the capacitor is now 240 V. The angular frequency ω is calculated as 2π * f. Substituting these values into the formula, we find that the maximum current is approximately 2.54 mA.
In summary, the maximum current in a capacitor depends on the capacitance, voltage, and frequency of the electrical source. The higher the voltage and frequency, the higher the maximum current. The provided values for the North American and European outlets yield different maximum currents due to the variation in their AV.rms voltage levels and frequencies.
Learn more about capacitor:
https://brainly.com/question/31627158
#SPJ11
A series RLC circuit consists of a 65 Ω resistor, a 0.10 H inductor, and a 20 μF capacitor. It is attached to a 120 V/60 Hz power line. Part A
What is the peak current I at this frequency? Express your answer with the appropriate units. I = ________ Value __________ Units Part B What is the phase angle ∅? Express your answer in degrees. ∅= ______________
The peak current (I) at this frequency is approximately 1.04 A and the phase angle (∅) is approximately -63.69 degrees.
Part A:
First, let's calculate the reactance values:
The inductive reactance (XL) can be calculated using the formula:
XL = 2πfL
Substituting the given values:
XL = 2π * 60 * 0.10 = 37.68 Ω
The capacitive reactance (XC) can be calculated using the formula:
XC = 1 / (2πfC)
Substituting the given values:
XC = 1 / (2π * 60 * 20 * 10^(-6)) = 132.68 Ω
Next, let's calculate the impedance (Z):
Z = √(R^2 + (XL - XC)^2)
Substituting the given values:
Z = √(65^2 + (37.68 - 132.68)^2) = √(4225 + (-95)^2) = √(4225 + 9025) = √13250 ≈ 115.24 Ω
Now, we can calculate the peak current (I):
I = V / Z
Substituting the given voltage value:
I = 120 / 115.24 ≈ 1.04 A
Therefore, the peak current (I) at this frequency is approximately 1.04 A.
Part B:
To find the phase angle (∅), we can use the formula:
∅ = tan^(-1)((XL - XC) / R)
Substituting the calculated values:
∅ = tan^(-1)((37.68 - 132.68) / 65) ≈ -63.69°
Therefore, the phase angle (∅) is approximately -63.69 degrees.
Learn more about current: https://brainly.com/question/1100341
#SPJ11
A 0.2-kg steel ball is dropped straight down onto a hard, horizontal floor and bounces Determine the magnitude of the impulse delivered to the floor by the steel ball .
The magnitude of the impulse delivered to the floor by the steel ball will be approximately 4 N·s.
To determine the magnitude of the impulse delivered to the floor by the steel ball, we can use the principle of conservation of momentum. When the ball bounces off the floor, its momentum changes, and an equal and opposite impulse is imparted to the floor.
Given;
Mass of the steel ball (m) = 0.2 kg
Initial velocity of the ball (v_initial) = -10 m/s (negative because it is downward)
Final velocity of the ball (v_final) = 10 m/s (positive because it is upward)
The change in momentum is;
Change in momentum = Final momentum - Initial momentum
The magnitude of momentum is given by;
Momentum (p) = mass (m) × velocity (v)
Before the bounce, the initial momentum of the ball is:
Initial momentum = m × v_initial
After the bounce, the final momentum of the ball is:
Final momentum = m × v_final
The change in momentum is;
Change in momentum = Final momentum - Initial momentum
= m × v_final - m × v_initial
Substituting the given values;
Change in momentum = (0.2 kg) × (10 m/s) - (0.2 kg) × (-10 m/s)
= 2 kg·m/s + 2 kg·m/s
= 4 kg·m/s
The magnitude of the impulse delivered to the floor is equal to the change in momentum;
Magnitude of impulse = |Change in momentum|
= |4 kg·m/s|
= 4 N·s
Therefore, the magnitude of the impulse delivered to the floor by the steel ball is 4 N·s.
To know more about magnitude here
https://brainly.com/question/30033702
#SPJ4
--The given question is incomplete, the complete question is
"A 0.2 kg steel ball is dropped straight down onto a hard, horizontal floor and bounces straight up. The ball's speed just before and just after impact with the floor is 10 m/s. Determine the magnitude of the impulse delivered to the floor by the steel ball. The answer is 4 Ns. Why?"--
In a battery, the anode and cathode are immersed in a solution of ions that delivers electric charge to each terminal. This solution is called __________ .
a. the anode
b. analog medium
c. the cathode
d. the electrolyte
e. the internal resistor
In a battery, the anode and cathode are connected through an electrolyte solution. The electrolyte plays a crucial role in facilitating the movement of ions and enabling the flow of electric charge within the battery.
The electrolyte solution consists of ions that can undergo oxidation and reduction reactions. These ions are typically dissolved in a liquid solvent, although electrolytes can also exist in gel or solid form. The choice of electrolyte depends on the specific type of battery and its intended application.
When a battery is connected to an external circuit, a chemical reaction takes place within the battery. At the anode, a chemical reaction releases electrons, which flow through the external circuit to the cathode. Meanwhile, in the electrolyte solution, ions move from the anode to the cathode, maintaining overall charge neutrality.
The electrolyte's role is multi-fold. First, it provides a conductive medium for the movement of ions. As the chemical reactions occur at the electrodes, the electrolyte allows the transfer of ions between the anode and cathode. This movement of ions ensures the flow of charge and sustains the battery's operation.
Second, the electrolyte also helps to balance the charges within the battery. As positive ions migrate towards the cathode, negative ions move towards the anode to maintain the overall electrical neutrality of the system.
Additionally, the electrolyte can impact the battery's performance, including its energy density, voltage, and internal resistance. Different electrolytes have varying properties that affect factors such as the battery's capacity, self-discharge rate, and temperature range of operation.
In summary, the electrolyte in a battery is a solution of ions that allows for the movement of charge between the anode and cathode. It serves as both a conductive medium and a means to balance the charges, enabling the battery to provide a sustained electric current. The choice of electrolyte is critical in determining the battery's performance characteristics and suitability for specific applications.
Learn more about battery
https://brainly.com/question/32262611
#SPJ11