Suppose we have the instruction LDA 800. Given memory as follows: Memory 800 900 900 1000 1000 500 1100 600 1200 800 What would be loaded into the AC if the addressing mode for the operating is immediate? A) 800 B) 900 C) 1000 D) 500 E) None of the above

The I/w ratio is the ratio of the current flowing through a transistor to the width of the transistor's channel.

The l/w ratio of the PMOS transistor in a pseudo-NMOS realization of a 2-input NOR gate should be determined by the design requirements of the circuit.

In general, the l/w ratio of a PMOS transistor is determined by the desired current-carrying capability and the voltage drop across the transistor. For a 2-input NOR gate, the PMOS transistor in the pull-up network should be designed to provide sufficient current to drive the output high, while the PMOS transistors in the input stages should be designed to have a low on-resistance to minimize the voltage drop across them.

The exact l/w ratio will depend on the specific design requirements of the circuit.

To Know More About Transistors, Check Out

https://brainly.com/question/29432407

#SPJ1

The structural element with a larger modulus of elasticity (e) is stiffer. The modulus of elasticity is a measure of the stiffness of a material, and a larger modulus of elasticity indicates a stiffer material.

Stiffer means that the structural element with a larger modulus of elasticity will be less flexible and will be more resistant to deformation under load. It will also be able to support a greater load before reaching its yield point. On the other hand, the structural element with a smaller modulus of elasticity will be more flexible and will be more susceptible to deformation under load. It will also be able to support a smaller load before reaching its yield point.

Learn more elasticity, here https://brainly.com/question/28790459

#SPJ4

Taking  the allowable design stress for aluminium as 90 N/mm². The estimated plate thickness required at base of tank is 0.1612m.

Stress is a force per unit area that occurs in materials as a result of external forces, uneven heating, or permanent deformation. It is used in physical sciences and engineering to accurately describe and predict the behavior of elastic, plastic, and fluid materials. A stress is defined as the product of a force divided by an area.

There are numerous types of stress. Shear stress is caused by forces that are parallel to and lie in the plane of a cross-sectional area of the material, as opposed to normal stress, which is caused by forces that are perpendicular to the area.

Learn more about stress

https://brainly.com/question/26108464

#SPJ1

Where you own two pottery stores in your city and you want to find the number of two particular vase colors (color) sold in both stores (location) each week (for each week). If are not interested in the sum total, note that the bar graph you should select to compare the data between both stores is: the "Stacked Bar Chart" (Option A)

When comparing data points, a stacked bar chart is generally simpler to notice the comparison than a combined chart.

When data points are stacked on top of each other, it is easier to discern the percentage of each data point relative to the total value.

Learn more about Stacked Bar Chart:
https://brainly.com/question/28903290
#SPJ1

knowledge extraction from data It is one of the processes in the procedure for discovering new knowledge. It is a computational process that combines techniques from machine learning, statistics, and database architecture to find patterns in massive data sets.

Data mining mostly serves the following four purposes: prediction capability. the method of extracting patterns from data utilizing a number of variables to forecast other variables with unknown types or values. The process of searching a database for a crucial feature of data.

Some data mining techniques include classification, clustering, association, data cleaning, and data visualization.

To know more about data mining visit :-

https://brainly.com/question/28561952

#SPJ4

The average carbon content in weight percent is 0.090%. To calculate the average of carbon is shown below.

High-carbon steel, of course, has the highest ratio of carbon to iron. It includes of more than 0.60% carbon, thereby changing its physical properties. Also called as carbon tool steel, it has around 0.61% to 1.5% carbon. The carbon percentage refers to a high percentage of carbon gives hardness and strength to the metal. It is primary used to tools like chisels, hammers, dies, punches, broaches, reamers, drills, taps, etc.

To determine the average carbon content in weight percent, the equation will be:

0.11 = ((6.67-x)/(6.67-0.02)). x

0.11 = (6.67 - x )/6.65x

73.15x = 6.67 - x

74.15 x = 6.67

x = 0.090%

Learn more about the average carbon, here https://brainly.com/question/8746255

#SPJ4

The Raspberry Pi may interact with electronic circuits via the GPIO pins to monitor and control the environment

To learn more about GPIO  refer,

https://brainly.com/question/29240962

#SPJ4

Since a person is setting up ANOVA one-way analysis of variance graph. The amount of  residual plots that they can view at one time is option D: three plots

A residual plot is a graph where the independent variable is on the horizontal axis and the residuals are displayed on the vertical axis.

Note that a linear regression model is adequate for the data if the residual plot's points are randomly distributed across the horizontal axis; otherwise, a nonlinear model is preferable.

So one can say that to verify an OLS linear regression model's assumptions, use residual plots. You run the danger of getting findings you cannot be able to rely on if you breach the assumptions. Residual plots show fitted values or another variable on the x-axis and the residual values on the y-axis.

Learn more about residual plots from

https://brainly.com/question/16821224
#SPJ1

The HR department should install wheelchair ramps and widen the doorways as they don't want to loose an exceptional systems engineer who hopes to work at the techtonic group.

What is a wheelchair ramps?

A wheelchair ramp is an inclined plane that can be installed in addition to or instead of stairs. Ramps make it easier for wheelchair users, as well as people pushing strollers, carts, or other wheeled objects, to enter a building.

The Americans with Disabilities Act requires wheelchair ramps (or other ways for wheelchair users to access a building, such as a wheelchair lift) in new construction for public accommodations in the United States.

A wheelchair ramp can be fixed, semi-fixed, or portable. Permanent ramps are intended to be bolted or otherwise attached to the ground. Semi-permanent ramps are commonly used in the short term and rest on top of the ground or concrete pad.

To know more about wheelchair ramps, visit: https://brainly.com/question/17395685

#SPJ4

The rotational velocity of the rudder mechanism to steer the ship is .1247 rad/sec.

Translational motion is when an object moves in a straight line, whereas rotational motion occurs when the same object moves in a circular route along an axis.

1)here rotational velocity and acceleration of the rudder can be found by relative velocity and acceleration method with Coriolis component of acceleration

2)here let's draw a velocity diagram as follow with the scale of

2 cm=.1 m/s

velocity triangle is given by AB'B, where AB' shows slider velocity along horizontal, AB along the tangent to link 2 or guide, and velocity of pin  BB' inside the guide along the length of the guide, here we know the velocity of AB' but don't know velocity AB and BB' hence draw them along given direction point of intersection is B point, so from the diagram, I get that

Vab'=2 cm=.1 m.s

Vbb'=.9 cm=.045 m/s

Vab=1.9 cm=.095 m/s

where rotational velocity is given by

Vab=Rab*wab

Rab=(.362+.7^2)^.5=.7615 m

wab=0.095/.7615=.1247 rad/s

To know more about rotational motion visit:

https://brainly.com/question/12995374

#SPJ4

To find the total reactive power supplied by the source to the line, we need to first calculate the total current flowing through the line.

We can do this by using Ohm's law to find the total resistance of the line, and then dividing the source voltage by the total resistance:

Total resistance = (120 + j60) / 120 V = 1 + j0.5 ohms

Total current = 120 V / (1 + j0.5 ohms) = 120 / (1.2 + j0.6) = 100 / 1.2 + j(-50) / 1.2 = 83.333 - 41.667j A

Next, we can use the total current and the source voltage to calculate the total reactive power supplied by the source to the line:

Total reactive power = (120 V) * (83.333 - 41.667j A) = 9960 - 5000j VAR

The total reactive power supplied by the source to the line is 9960 - 5000j VAR.

To Know More About Ohm's law, Check Out

https://brainly.com/question/1247379

#SPJ4

Answer:

search it bro

Explanation:

use it, it will give precise answer

The number of residual plots that you can view at one time is A. two plots.

Analysis of variance is a collection of statistical models and the estimation procedures that go with them that are used to analyze the differences between means. Ronald Fisher, a statistician, invented ANOVA.

ANOVA, which stands for Analysis of Variance, is a statistical test used to compare the means of multiple groups. ANOVA ("analysis of variance") compares the means of two or more independent groups to see if there is statistical evidence that the associated population means differ significantly.

In conclusion, the correct option is A.

Learn more about ANOVA on:

https://brainly.com/question/25800044

#SPJ1

After conducting a cylinder leakage test, Technician A is correct.

What is a cylinder head?

The cylinder head serves as the ceiling of the combustion chamber in an internal combustion engine and is located above the cylinders. They are essential for managing fuel deployment and airflow into and out of the cylinders.

The engine valves are located in the cylinder head. Allowing air into and out of the cylinder is the main purpose of the engine valve. The cylinder head, which houses more moving parts than any other component of the engine, also houses the injectors and valves.

To learn more about a cylinder valve, use the link given
https://brainly.com/question/18204706
#SPJ4

Answer: Technician B is correct.

In a linkage-operated clutch system, the free play should be adjusted at the pedal pushrod which is usually under the dash.

Clutch slip will occur if there is insufficient free play (or clearance), as the pressure plate won't be able to fully press against the friction plate. If this problem isn't fixed right away, a burned-out friction plate and potentially a damaged pressure plate will result.

What is Clutch Operated Linkage?

A stiff component of the flywheel and consequently the crankshaft assembly is the clutch unit.

As a result, it experiences vibrations from the engine and transmission as rocking, shaking, and pitching.

On the other hand, the clutch foot-pedal assembly is fastened to the body framework. As a result, the body may experience minor bumps and rebound motions.

To know more about Clutch, visit: https://brainly.com/question/13507668

#SPJ4

Angled Physical Contact polish

So, To replace the fiber optic cable that connects two switches. If it is found that the existing fiber cable to ensure it has LC connectors and also if the cable's ferrule has a slight slant to it.

Angled Physical Contact polish should be used to replace the existing cable.

What is Angled Physical Contact polish?

APC Connector is a type of fiber connector that reduces back-reflection by applying a 5° to 15° angle-polish to the end faces.

Because of the angle, the reflected light escapes into the cladding rather than remaining in the fiber core.

Angled connectors should only be mated with other angled connectors. When mated to a non-angle polished connector, insertion loss is extremely high. Angle-polished connectors typically have a higher insertion loss than good quality straight physical contact connectors.

When connected, "Ultra" quality connectors may achieve back reflection comparable to an angled connector, but an angled connection maintains low back-reflection even when the output end of the fiber is disconnected.

To know more about fiber Optics, visit: https://brainly.com/question/15741826

#SPJ4

friction drag = 54546 lbf

A coal barge is 1000-ft-long, 100-ft-wide, and is submerged in 12 feet of 60°F water. If it is being towed at 12 mph, the friction drag would be 54546 lbf.

What is a Friction drag?

Friction is the resistance that occurs when two objects rub together, such as air against an airplane. Friction contributes to drag.

Because the barge is rectangular, the flow over the submerged sides and bottom is assumed to behave like B.L. over a flat plate.

Effects at the corners and leading/trailing edges are not taken into account, which could lead to deviations from the analysis. Given the size of the barge, we expect these effects to be minor.

To know more about friction, visit: https://brainly.com/question/29355763

#SPJ4

Answer:

This program uses the int 16h interrupt to query an integer from the keyboard and store it in the al register. The program then enters a loop, in which it calculates the next day of the week using the add, mov, div, and cmp instructions, and displays the appropriate message using the int 21h interrupt. The program exits the loop and ends when the user presses the ESC key (ASCII code 27).

Answer:

class Car {

 private String model;

 private String year;

 private double price;

 public Car(String model, String year, double price) {

   this.model = model;

   this.year = year;

   if (price > 0) {

     this.price = price;

   }

 }

 public String getModel() {

   return model;

 }

 public void setModel(String model) {

   this.model = model;

 }

 public String getYear() {

   return year;

 }

 public void setYear(String year) {

   this.year = year;

 }

 public double getPrice() {

   return price;

 }

 public void setPrice(double price) {

   if (price > 0) {

     this.price = price;

   }

 }

}

class CarApplication {

 public static void main(String[] args) {

   Car car1 = new Car("Toyota", "2020", 20000);

   Car car2 = new Car("Honda", "2019", 25000);

   System.out.println("Original price of car1: $" + car1.getPrice());

   System.out.println("Original price of car2: $" + car2.getPrice());

   car1.setPrice(car1.getPrice() * 0.95);

   car2.setPrice(car2.getPrice() * 0.93);

   System.out.println("Discounted price of car1: $" + car1.getPrice());

   System.out.println("Discounted price of car2: $" + car2.getPrice());

 }

}

At this stage, Segway was involved in "alpha testing", when Segway manufactured its two-wheeled people movers, it built a prototype and had staff engineers test it for performance and stability.

What exactly is a Protoype?

Prototyping is an important step in the creation of any product, digital or physical. The process transforms the concept into a physical structure. This concept can be presented to stakeholders or an audience to validate assumptions and test its viability.

In simple terms, a prototype is not just a component of product design; it is one of the most important components of -

Prototyping is an essential step in the startup process without which all subsequent steps are pointless.

To know more about Protoype, visit: https://brainly.com/question/17205672

#SPJ4

The term "complex power" refers to the mathematical representation of electrical power. It has both real and fictitious parts, just like a complex number.

The active power is represented by the real part, while the reactive power is represented by the imaginary part. The letter S is frequently used to represent it.

The complex conjugate of the rms current phasor and the rms voltage phasor make up the complex power (in VA). As a complex quantity, its real and imaginary parts are real power P and reactive power Q, respectively.

Since the magnitude of the complex power is the apparent power, we could write it as:

S=S∠θ v−θ i

​However, mathrm pf = cos(theta_v-theta_i) pf = cos(v i)

v i = cos 1 pf = 45 In this case, the value of the ta_v-theta_i v i is positive due to the exercise's knowledge that current lags voltage. The value of the complex power is:

Boxed mathbf S=120, angle 45, circle mathrm VA S=120, 45, VA

a) "mathbf S=120 angle 45 circle" "mathrm VA S=120 45"

To learn more about complex power here:

https://brainly.com/question/2355649

#SPJ1

Complete Question = A 110-V rms, 60-Hz source is applied to a load impedance Z. The apparent power entering the load is 120 VA at a power factor of 0.707 lagging. (a) Calculate the complex power. (b) Find the rms current supplied to the load. (c) Determine Z. (d) Assuming that Z = R + jωL, find the values of R and L.

In accordance with 250.118(1), A MC cable includes an insulated or uninsulated equipment grounding conductor.

When does MC cable is recognized by the NEC as an equipment grounding conductor?

Type MC cable that provides an efficient ground-fault current path in compliance with one or more of the following is :

To know more about MC cable, visit: https://brainly.com/question/14934410

#SPJ4

The word that best completes the sentence. is "MInimize"

Thus, Osha's standards require your employer to ensure that lighting, equipment, motors, machines, appliances, switches, controls, and enclosures are constructed and installed to MInimize electrical dangers.

OSHA standards are guidelines that specify how companies must safeguard their employees from dangers. OSHA rules are divided into four categories: general industry, building, maritime, and agriculture. (The General Industry set relates to the greatest number of people and workplaces.)

OSHA standards include requirements to provide protective clothing, prevent tunneling cave-ins, reduce exposure to some communicable diseases, guarantee the safety of workers entering confined spaces, prevent exposure to potentially harmful substances such as asbestos and lead, and install machine guards, among other things.

Learn more about OSHA:
https://brainly.com/question/29345131?
#SPJ1

Any subnode of a given node is called a child node, and the given node, in turn, is the child's parent.

To learn more about ancestor node refer to:

https://brainly.com/question/29749643

#SPJ4

Capturing carbon dioxide is advantageous for oil corporations.

When fossil fuels are burned, a greenhouse gas called carbon dioxide is massively released into the atmosphere. Greenhouse gases, which trap heat in our atmosphere, are to blame for global warming.

Before carbon dioxide (CO2) is released into the atmosphere, it is captured and stored through the process of carbon capture and storage (CCS). The technique can absorb up to 90% of the CO2 produced while burning fossil fuels to produce power and for industrial purposes like making cement.

To know more about oil visit:-

https://brainly.com/question/29530758

#SPJ4

With the load impedance open-circuited, the Thevenin voltage is calculated. Find the voltage at the load terminals that is open-circuit.

Thevenin's Theorem: What is it? According to Thevenin's Theorem, any linear circuit can be made simpler by using a single dc voltage and a series resistance, regardless of how complex it is.

It makes the less crucial section of the circuit simpler and makes it possible for us to see the output part's operation in real time. It simplifies a complicated circuit by putting one emf source in series with one resistance.

To know more about Thevenin's Theorem visit:

https://brainly.com/question/28007778

#SPJ1

The cash flow diagram is shown below:

Year Deposit Withdrawal Balance

0 P - P

1 - - P

2 - 2,000 P + 1,708.50

3 - 2,000 P + 3,571.51

4 - 2,000 P + 5,539.52

5 - 2,000 P + 7,614.45

6 - 3,000 P + 5,978.7

7 - 3,000 P + 4,037.48

8 - 3,000 P + 2,068.83

What  is deposit ?

Placing cash  with an organization, most frequently a financial institution like a bank, is known as making a deposit. The deposit is a credit again for person that made it, and it may be withdrawn in line with the terms agreed upon at the time of deposit, passed to some other party, or applied to a purchase at a later time.

To know more about deposit
https://brainly.com/question/2507231
#SPJ1

Zin (s/c) = j45 was recorded as the input impedance when the circuit was terminated in a short circuit.

Find ZL/Z0 on the chart and draw a circle across it with the centre placed at 1+j0 to find Z along the line for that particular ZL. Points on that circle represent impedance on the line corresponding to distance which is read from the scale "wavelengths toward the generator".

The Wavelengths towards generator(WTG) scale is the outermost scale circling the Smith chart. It was built to indicate movement on the transmission line toward the generator, in wavelength units. Consequently, l is measured in wavelengths and in whole rotations.

To know more about impedance  visit:-

https://brainly.com/question/2263607

#SPJ4

The appropriate machine instruction in assembly language for the Skipcond 800 given the following instruction set.

The primary distinction between assembly language and machine code is that the latter is a low-level programming language that needs an assembler to translate it into machine code. Machine code, on the other hand, is a language made up of binaries that can be run by computers directly.

The most basic form of information stored in a computer system is binary information, which is also frequently referred to as machine language. Physically speaking, a computer system's central processing unit stores the 0s and 1s utilizing.

To know more about assembly language visit :-

https://brainly.com/question/14728681

#SPJ4

The current and the resistance are obtained according to Ohm's First Law, which states that the voltage is obtained by the multiplication of the resistance and of the current, as follows:

V = R x I.

The variables are:

At resistor R2, we have that:

Hence the current I1 is obtained as follows:

1800 x I1 = 7.2

I1 = 7.2/1800

I1 = 0.004A = 4mA.

Then for resistor R1, we have that:

Hence the resistance R1 is obtained as follows:

0.004R1 = 4.8

R1 = 4.8/0.004

R1 = 1200 ohms.

More can be learned about Ohm's First Law at https://brainly.com/question/231741

#SPJ1