Answer:
The area estimate is somewhat inaccurate because the length * width of the shoe will be an inaccurate measurement of the area of the shoe that actually contacts the floor.
Which of the following energies is related to temperature change
Thermal energy is a type of energy that is related to temperature change. Details about thermal energy can be found below.
What is thermal energy?Thermal energy refers to the internal energy of a system in thermodynamic equilibrium due to its temperature.
Thermal energy of a body is determined by the difference in temperature in the surrounding environment and the body.
Therefore, thermal energy is a type of energy that is related to temperature change.
Learn more about thermal energy at: https://brainly.com/question/11278589
#SPJ1
Photovoltaic cells: a) have become more economical to produce and use over the past 25 years. b) are the most efficient means of converting solar energy to electricity. c) are currently only used in urban areas of highly developed countries. d) have only been adapted for use in small appliances.
Photovoltaic cells are the most efficient means of converting solar energy to electricity. Option b is correct.
What is a cell?A cell is a voltage and current-producing device that consists of a single anode and cathode separated by an electrolyte.
One or more cells can make up a battery. One cell, for example, is one AA battery.
Light intensity on a solar cell is often measured in "suns," with one sun roughly equivalent to 1 kW/m².
Concentrated sunlight improves the ratio of current generated while the device is lighted vs when it is dark, hence enhancing output voltage and efficiency.
Photovoltaic cells are the most efficient means of converting solar energy to electricity.
Hence, option b is correct.
To learn more about the cell refer to:
https://brainly.com/question/3142913
#SPJ1
Planetary Nebula/White Dwarf Stars - Little Ghost Nebula. Some red giant stars develop into planetary nebulas as their cores continue to contract, to increase in temperature, and to burn and vent the remaining gases into interstellar space. Eventually, the core collapses to the point where it is hot enough to ionize the vented gases, forming a relatively short-lived (~10,000-20,000 years) planetary nebula. The remaining core collapses into a white dwarf star. The vented materials from the planetary nebula play an important role in enriching the universe in elements with atomic weights less than 26 (forming the basis for carbon-based life like ourselves!). Which type of star will form a planetary nebula
Smaller stars, like our sun, die by ejecting their outer layers of gas into space, resulting in the formation of a planetary nebula.
How planetary nebula formed?A planetary nebula is formed when a red giant ejects its outer atmosphere. A white dwarf is the carbon core of a star that has lost its photosphere.
This results in a one-of-a-kind and breathtaking creation known as a planetary nebula.
Smaller stars, like our sun, die by ejecting their outer layers of gas into space over a 10,000-year period, leaving behind the star's heated core.
Radiation from the white dwarf causes the gas to shine, resulting in a one-of-a-kind and stunning creation known as a planetary nebula.
The carbon core of a red giant that has evacuated its photosphere as a planetary nebula is a white dwarf.
Hence, Smaller stars, like our sun, die by ejecting their outer layers of gas into space type of star will form a planetary nebula
To learn more about the planetary nebula refer to:
https://brainly.com/question/1162533
#SPJ1
You suspect that the power supply in your desktop pc is failing. you want to use a multimeter to test the power supply. which multimeter setting should you use
The multimeter setting should you use is between 11-12 volts. If the voltage is too high or too low, the power supply must be changed.
What is a multimeter?An instrument made to measure resistance, voltage, and electric current, often across a range of values.
You think your desktop computer's power supply is malfunctioning. To test the power supply, you should use a multimeter.
Between 11 and 12 volts should be seen on the multimeter. The power supply is failing and has to be replaced if it's too high or too low.
Hence, the multimeter setting should you use is between 11-12 volts.
To learn more about the multimeter refer:
https://brainly.com/question/5135212
#SPJ1
Which would result in a judge who is sitting beside the testing ground observing the tennis ball having a speed of 7 m/s?
Considering the frames of reference, the robot has to fire backwards at a speed of 2m/s.
What is relative velocity?The relative velocity is obtained based on the inertial frame of reference. The term velocity is always measured relatively.
Given that the inertial frame of reference is relative to the moving frame then; 7m/s - 9 m/s = -2m/s.
It then follows that the robot has to fire backwards at a speed of 2m/s.
Missing parts:
Basim’s robotics team builds a robot that travels at 9 m/s and can fire a tennis ball at a target.
Which would result in a judge who is sitting beside the testing ground observing the tennis ball having a speed of 7 m/s?
The robot fires the ball forward with a speed of 7 m/s.
The robot fires the ball backward with a speed of 7 m/s.
The robot fires the ball backward with a speed of 2 m/s.
The robot fires the ball forward with a speed of 2 m/s.
Learn more about frame of reference:https://brainly.com/question/12222532?
#SPJ1
Answer:
C. the robot fires the ball backward with a speed of 2 m/s.
Which of the following is NOT an example of evidence that can be used to support the theory of evolution?
A. DNA evidence
B. Embryonic structures
C. Anatomical structures
D. Similar appearances in modern day organisms
Why is the same side of the Moon always visible from Earth?
A.) The Moon does not rotate about its axis.
B.) The Moon does not revolve around Earth.
C.) The Moon takes the same time to rotate about its axis as it takes to orbit Earth.
D.) The Moon and the Earth take the same time to rotate about their respective axes.
Answer:
Explanation:
Answer
The true fact is that C is what happens in outer space. Both rotations take 27.3 days.
A: The exact opposite is true. It does rotate about it's axis.
B: Again this is just plain false. Given the way we observe it, the moon must be rotating around the earth.
D. they don't. 27.3 hours and 24 hours are not the same.
Which option is an example of an object that has potential energy followed by an object that has kinetic energy?
A ball held over a person's head | a ball rolling on the floor is an example of an object that has potential energy followed by an object that has kinetic energy.
What is Kinetic energy?This is the type of energy possessed by a body by virtue of its motion or movement.
The rolling ball therefore has kinetic energy while a ball being held over a person's head has potential energy which is the energy possessed by a body by virtue of its position.
Read more about Kinetic energy here https://brainly.com/question/8101588
#SPJ1
A satellite with a mass of 120 kg fires its rocket thrusters, which give an impulse of 7440 kg-m/s. What was the total change in the velocity of the satellite — that is, what was the total AV?
A. 17 m/s
B. 88 m/s
C. 45 m/s
D. 62 m/s
From the calculation and the momentum of the body, the velocity is 62 m/s
What is momentum?The term momentum refers to the product of mass and velocity. Now recall that the rate of change of momentum is equal to the impressed force.
Hence;
7440 kg-m/s = 120 kg * v
v= 7440 kg-m/s/120 kg
v = 62 m/s
Learn more about momentum:https://brainly.com/question/24030570
#SPJ1
a carmboard 4ft x 4ft Square has the queen at the centre the queen is hit by the striker moves to the front edge, rebounds and goes inta hole behind the striking line. find the magnitude of displacement of queen a) from the centre to front edge b) from the front end edge to hole (c) from centre to hole.
Diagonal of cardboard=displacement to hole
√4²+4²4√2So displacement till edge
4√2/22√2Total distance
4√2+2√26√2ftFrom centre to hole displacement
2√2If you had to choose a theory that best represents your own view of development, would you choose a single theory or would you select components of several different theories? what aspect of your chosen theory (or theories) make it more attractive than others
I would select components of several different theories and the aspect which will be more attractive will be the one which has similarities and accurate.
What is a Theory?This is defined as a proposed explanation for a particular phenomenon or occurrence.
Components of several different theories will bring different dimensions and factors to the occurrence which will help in its thorough analysis.
Read more about Theory here https://brainly.com/question/11555274
#SPJ1
Some iron has a coefficient of linear expansion of 12 x 10-6 / o K . A 100 mm length of iron piping is heated through 20 K. The pipe extends by:
Given that the linear expansion of the pipe is 12×10¯⁶ K¯¹, the pipe extends by 0.024 mm
Data obtained from the question Original length (L₁) = 100 mmChange in temperature (ΔT) = 20 KCoefficient of expansion (α) = 12×10¯⁶ K¯¹Change in length (ΔL) =?How to determine the new diameter
α = ΔL / L₁ΔT
12×10¯⁶ = ΔL / (100 × 20)
12×10¯⁶ = ΔL / 2000
Cross multiply
ΔL = 12×10¯⁶ × 2000
ΔL = 0.024 mm
Learn more about linear expansion:
https://brainly.com/question/23207743
#SPJ1
A 1050 w electric toaster operates on a household circuit of 120 v. what is the resistance of the wire that makes up the heating element of the toaster
The Resistance of the wire that makes up the heating element of the toaster is 13.75Ω.
What is Resistance?
Resistance is the measure of the opposition to current flow in an electrical circuit.
S.I. Unit of resistance is ohms, symbolized by the Greek letter omega (Ω)
Also from Ohm's Law,[tex]R=\frac{V}{I}[/tex]
From power-current relation
P=VI
Also, [tex]I=\frac{P}{V}[/tex]
[tex]I = \frac{1050}{120}[/tex]
I = 8.75 A
From Ohm's Law,[tex]R=\frac{V}{I}[/tex]
[tex]R = \frac{120}{8.75}[/tex]
R = 13.75 Ω
The Resistance of the wire is 13.75 Ω
For more resistance questions visit
https://brainly.com/question/14547003
#SPJ1
Determine the frequency of the radar wave. [Show all calculations, including the equation and substitution with units.]
The frequency of the radar wave is 4.166 Hz.
What is wavelength?The wavelength is the distance between the adjacent crest or trough of the sinusoidal wave. The wavelength is the reciprocal of the frequency of the wave.
Wavelength λ = 1/f
A 0.12-meter-long electromagnetic (radar) wave is emitted by a weather station and reflected from a near by thunderstorm.
The radar wave travels double the distance 0.12 m.
λ = 2 x 0.12 = 0.24 m
Then, the frequency of the radar wave is
f= 1 / 0.24
f =4.166 Hz
Thus, the frequency of the radar wave is 4.166 Hz.
Learn more about wavelength.
https://brainly.com/question/13533093
#SPJ1
Sherry and Ellen are talking about the factors that affect light scattering in the atmosphere. Sherry says one factor is the length of the path of sunlight. Ellen says one factor is altitude. Who is correct
Sherry who says one factor is the length of the path of sunlight is correct.
Factors affecting light scatteringThere are two main factors which affects light scattering, and they include the following;
the size of the particles wavelength of the lightlength of the path of sunlight is equivalent to wavelength of the light.
Thus, we can conclude that Sherry who says one factor is the length of the path of sunlight is correct.
Learn more about light scattering here: https://brainly.com/question/1381101
#SPJ1
The student notices that the electronic balance has a zero error, so it shows
mass readings that are all slightly too small.
This means that the density value is
A)incorrect and slightly too large
B)incorrect and slightly too small
C)correct because the student used three significant figures
D)correct because the mass of the block is more than zero
The student notices that the electronic balance has a zero error, so it shows mass readings that are all slightly too small. This means that the density value is incorrect and slightly too small. The correct option is B.
The density is the ratio of the mass and the volume of the object. It is denoted by ρ.
ρ = mass/Volume = m/V
The student notices that the electronic balance has a zero error, so it shows mass readings that are all slightly too small.
As mass is directly proportional to density. The density will also be slight small when mass reading are all slightly small.
Thus, the correct option is B.
Learn more about density.
https://brainly.com/question/9215083
#SPJ1
when two bodies of diffrent temprature in contact, heat will
Answer:
When two bodies at different temperatures are placed in thermal contact with each other, heat flows from the body at a higher temperature until they both reach the same temperature.
Explanation:
4. A weightlifter lifts a set of weights a vertical distance of 2 meters. If a constant net force of 350 N is exerted on the weights, what is the net work done on the weights?
Answer:
700 J
Explanation:
Work = Force * Distance
Work = 350 N * 2 M = 700 J
Which property of sound waves decreases as the square of the distance from the source increases? A. Pitch
B. Intensity C. Wavelength D. Speed
Intensity is the property of sound waves that decreases as the square of the distance from the source increases. Option B is correct.
What is a sound wave?A sound wave is produced when a medium begins to vibrate. When an entity vibrates, a pressure wave is formed, which causes sound.
As the square of the distance from the source increases, the intensity of sound waves decreases.
Sound intensity relationship
[tex]\rm {I} = \frac{1}{r^2}[/tex]
[tex]\rm \frac{I_2}{I_1} =\frac{r_1^2}{r_1^2}[/tex]
Hence, option B is correct.
To learn more about the sound wave, refer to
https://brainly.com/question/11797560.
#SPJ1
(
the average power transferred to the solar panels by sunlight is 26 000 w
calculate the average energy transferred to the solar panels in 30 seconde
use the equations
energy transferred = power time
Answer:
P = E / t definition of power is energy / unit time
1 W = 1 Joule / sec definition of 1 Watt of power
E = 2.6E4 J/s * 30 s = 7.8E5 Joules = 780,000 Joules
The average power transferred to the solar panels by sunlight is 26 000 w. The average energy transferred to the solar panels in 30 seconds is 780,000 joules.
To calculate the average energy transferred to the solar panels in 30 seconds, we can use the equation:
Energy transferred = Power × Time
Given that the average power transferred to the solar panels is 26,000 watts and the time is 30 seconds, we can substitute these values into the equation:
Energy transferred = Power × Time
Energy transferred = 26,000 × 30
Energy transferred = 780,000 watt-seconds
Since the watt-second is equivalent to the joule (J), the energy transferred to the solar panels is 780,000 joules.
Therefore, the average energy transferred to the solar panels in 30 seconds is 780,000 joules.
To know more about energy and power:
https://brainly.com/question/34423421
#SPJ5
How does newton’s third law of motion relate to a catapult?
PLEASE ANSWER ASAP. WILL GIVE BRAINLIEST
Answer: the force when the catapult swings has the same force as it does when coming down
Explanation:
for every reaction there is an equal opposite reaction
Where are heavier elements, like iron or gold made?
*
1 point
In space, between the stars
in the black holes at the centers of galaxies
In the hearts of stars
They were made as part of the big bang
Answer:
In the hearts of stars:
Theory tells us the elements heavier than iron are created by novas
that is when a star explodes, and any heavier elements were once created when a star exploded.
Which statement belongs to daltons atomic theory
Atoms cannot be broken down into smaller pieces is the statement belongs to daltons atomic theory. Option B is correct.
What is an atom?The atom consists of matter that may be split without releasing electrical charges. It's also the smallest unit of matter with chemical element features.
The complete question is:
"Which statements belong to Dalton's atomic theory? Select all that apply.
A)Atoms cannot be created or destroyed.
B)Atoms cannot be broken down into smaller pieces.
C)All atoms of an element are identical.
D)Chemical reactions cause atoms to be rearranged."
According to Dalton's atomic hypothesis, atoms cannot be broken down into smaller bits.
Hence, option B is correct.
To learn more about the atom refer to the link;
https://brainly.com/question/1566330
#SPJ1
A 950-kg car strikes a huge spring at a speed of 22m/s (fig. 11-54), compressing the spring 5.0m. (a) what is the spring stiffness constant of the spring? (b) how long is the car in contact with the spring before it bounces off in the opposite direction?
(a) The spring stiffness constant of the spring is 18,392 N/m.
(b) The time the car was in contact with the spring before it bounces off in the opposite direction is 0.23 s.
Kinetic energy of the carThe kinetic energy of the car is calculated as follows;
K.E = ¹/₂mv²
K.E = ¹/₂ x 950 x 22²
K.E = 229,900 J
Stiffness constant of the springThe stiffness constant of the spring is calculated as follows;
K.E = U = ¹/₂kx²
k = 2U/x²
k = (2 x 229,900)/(5)²
k = 18,392 N/m
Force exerted on the springF = kx
F = 18,392 x 5
F = 91,960 N
Time of impactF = mv/t
t = mv/F
t = (950 x 22)/(91960)
t = 0.23 s
Learn more about spring constant here: https://brainly.com/question/1968517
#SPJ4
Which form of energy is converted to electrical energy in a voltaic cell?.
Answer:
chemical energy is converted to electrical energy in a voltaic cell.
A massless rod is attached to the ceiling by a string. Two weights are hung from the rod: a 0.4-lb weight at its left end and a 1.2-lb weight at its right end. The length of the rod is L and a string is attached (3L/4 from its left end) so that the rod (with attached weights) is horizontal. What is the tension in the string supporting the rod and the attached weights
The tension in the string supporting the rod and the attached weights is 7.11 N.
Tension in the string supporting the rodThe tension in the string supporting the rod and the attached weights is the sum of the weights supported by the strings.
T = (m1 + m2)g
where;
m1 and m2 are the two masses supported0.4lb + 1.2lb = 1.6lb = 0.725 kg
T = 0.725 x 9.8
T = 7.11 N
Learn more about tension here: https://brainly.com/question/918617
#SPJ1
A bat strikes a 0.145 kg baseball with force of 5800 N. What acceleration does the baseball experience?
Answer:
40,000 m/s²
Explanation:
The formula is given as Force = mass × acceleration, so then acceleration = Force / mass.
Therefore...
5800 N ÷ 0.145 kg = 40,000 m/s²
HELP!
how did Mario Molina contribute to science?
i need like a mini paragraph:(
Mario Molina helped to bring about the 1987 Montreal Protocol on substances that result in depletion of the Ozone Layer.
What is ozone layer?The topmost layer of the atmosphere which protect the harmful UV rays from the Sun to reach the Earth surface.
Mario Molina has the great contribution in science field. He tried hard and succeeded in passing an international agreement to eliminate CFCs also called as Chloro Fluoro Carbons and other ozone-depleting chemicals.
These CFCs were used in jet planes which depleted the ozone layer and a hole was observed over Antarctica.
Learn more about ozone layer.
https://brainly.com/question/14330630
#SPJ1
5.4.2 Test (CST): Earth's Resources
Question 5 of 15
▬▬
The human population grows by about 2 percent each year, showing
growth.
OA. exponential
OB. linear
OC. cubic
The human population which grows by about 2 percent each year, is showing linear growth.
What is linear increment?
A linear increment occurs when a sequence increases gradually with a constant value.
If a population increases at the rate of 2%, the incremental rate or constant factor is 2%, thus, we can conclude that the human population which grows by about 2 percent each year, is showing linear growth.
Learn more about linear increment here: https://brainly.com/question/2511791
#SPJ1
A race car sits at the starting line on a racetrack. When the race starts, the car's tires exert a force on the track. According to Newton's third law of motion, WHAT PREVENTS THE RACE CAR FROM SINKING INTO THE TRACK?
A. The force of friction between the car tires and the track prevents the car from moving.
B. The track surface exerts a force that is larger and in the same direction as the force exerted by the tires.
C. A normal force that is equal in magnitude and opposite in direction to gravity pushes on the car.
D. The track exerts a force that is equal and in the opposite direction as the force exerted by the tires.
To prevent the race car from sinking into the track, the track exerts a force that is equal and in the opposite direction as the force exerted by the tires.
What is Newton's third law of motion?
Newton's third law of motion states that force every action there is equal and opposite reaction.
That is the force exerted on an object is equal in magnitude to the reaction of the object.
Fa = - Fb
According to this law, Fa is equal to Fb in magnitude but the directions are different.
Thus, to prevent the race car from sinking into the track, the track exerts a force that is equal and in the opposite direction as the force exerted by the tires.
Learn more about Newton's third law of motion here: https://brainly.com/question/62770
#SPJ1