Answer:
it is true
Explanation:
I don’t know why but maybe it’s because they just want you to pay for more than you goes?
The factor of safety is very important in design. It is determined by comparing the allowable stress to actual stress. What is known if the range of the factor of safety is between .75 and 1
Explanation:
A factor of safety is the load-carrying capacity of a system beyond what the system actually supports. Bridges, buildings, safety equipment, and fall protection all start with a factor of safety.
Simply put, the safety factor is how much stronger a system is than required. The factor of safety is the backbone of all structures and safety equipment and originates with engineers. In the planning phase of all structures and safety equipment, engineers determine the required overload from any object to remain safe in the event of an emergency.
For reliability, structures are typically built stronger than necessary. This is in case a structure experiences a heavier-than-expected load. This is a factor of safety. Ultimately, the amount of stress and overload a structure can handle comes down to the material used to build it.
Determining the factor of safety:
Engineers perform strength tests to determine how much weight a material can handle. Certain materials are more ductile than others, meaning they deform to pressure before breaking more so than others, like brittle materials. Brittle materials simply break once they meet the maximum force.
Ductile materials use yield strength to determine the safety factor. Brittle materials use the ultimate strength.
Yield strength: Determines the safety factor until the start of deformation.
Ultimate strength: Determines the safety factor until failure.
Ductile materials often test the factor of safety against yield and ultimate strengths while brittle materials usually only calculate the ultimate safety factor since the yield and ultimate values are often so close.
The necessary factor of safety of any structure determines the materials used. If a structure has a high required factor of safety, then engineers use a ductile material to build it. The realized factor of safety determines the amount of material used.
Required (design factor): A constant value imposed by law or standard. A structure is required to meet this value at a minimum.
Realized
jumble letters for WROBN plsss answer
Answer:
brown.
Explanation:
it could be brown.
a pipe discharges wine into a 1.5m diameter tank. Another pipe (15cm diameter), located near the base of the, is used to discharge wine out of the tank. Calculate the volumetric flow rate into the tank if the wine level remains constant at 2.5m.
The volumetric flow rate into the tank if the wine level remains constant at 2.5m is; 0.1232 m³/s
How to Calculate Volumetric Flow Rate?The formula for volumetric flow rate is;
V' = area * velocity
We are given;
Diameter; d = 15 cm = 0.15 m
Thus;
Area; A = (π/4)d²
A = (π/4)(0.15)²
A = 0.0176 m²
Velocity is; v = √(2gh)
v = √(2 * 9.8 * 2.5)
v = 7 m/s
Thus volumetric flow rate is;
V' = 0.0176 * 7
V' = 0.1232 m³/s
Read more about Volumetric Flow Rate at; https://brainly.com/question/15135598
#SPJ1
If the standpipe system has an automatic water supply or is part of a combined system, a _______ should go to the exterior of the building and provide a means to safely remove the system water so it will not be a hazard
When the standpipe system has an automatic water supply or is part of a combined system, a main drain should go to the exterior of the building.
What is Standpipe systems?This is known to be a system that is made of piping and hose linkage tht is often installed in all of a building to give reliable water for use.
Note that in the above scenario, When the standpipe system has an automatic water supply or is part of a combined system, a main drain should go to the exterior of the building.
Learn more about water supply from
https://brainly.com/question/19570750
#SPJ1
Explain the surprising realization scientists are making about bacteria and what danino hopes to eventually be able to do using bacteria. hurry 30 points
The surprising realization scientists are making about bacteria and what danino hopes to eventually be able to do using bacteria are the Corallococcus exercitus.
Who discovered the bacteria?Antonie van Leeuwenhoek used single-lens microscopes, which he made, to make the primary observations of micro organism and protozoa. His full-size studies at the boom of small animals inclusive of fleas, mussels, and eels helped disprove the concept of spontaneous era of life.
Researchers found a brand new species of alga in vital New York and named it Gormaniella terricola, with the genus named after poet Amanda Gorman.
Read more about the bacteria:
https://brainly.com/question/25236237
#SPJ1
You measure the length of a short pipe nipple that must be cut and arrive at the fraction 28/32 inch. reduce this fraction to its lowest terms. this fraction, expressed in its lowest terms, is inch.
Answer:
7 8 inch
Explanation:
when servicing piston rods and pins it is important to always
Answer:
Pistons should be inspected and measured.
Explanation:
When did Brainly come out and who was the first person on there besides the makers?
Please don’t give me lame answers or they will get reported
Thank you! :)
Answer:
i have actually been wondering this also. its a really great tool to have
Explanation:
Answer:
BRAINLY EXPERT✓
Explanation:
Initially called Zidane. pl, the company was founded in 2009 in Poland by Michał Borkowski (currently chief executive officer), Tomasz Kraus, and Łukasz Haluch. The first million unique monthly users were achieved within 6 months after the release.[5]
In January 2011, the company founded Znanija.com, the first international project dedicated to Russian language speakers.[6] Several other versions in multiple languages for the following markets included Turkey (eodev.com), Latin America and Spain (brain. lat), and Brazil (brainly.com.br).
This is the inside of my motorcycle fuel tank what are those spots and should I be worried ?
Technician a says that the intake valve is closed during the power stroke. technician b says that the exhaust valve is closed during the compression stroke. who is right?
Answer:
trick question - they are both right.
Explanation:
Both valves are closed during compression and power stroke or both strokes would be useless.
A ladder of length l is leaning against a domed roof with a radius r. The base of the ladder is distance d from the base of the dome. The ladder begins to slide. Determine the IC at the moment the ladder slides if:
l = 2 m
r = 1 m
d = 0.5 m
And the x-y origin is centered at the left base of the ladder (point O).
The IC at the moment the ladder slides based on the lengths and other information given will be (0, 1.32)
How to calculate the IC?From the information given, the calculation will be computed below:
l cos a = 1.5
cos a = 1.5/2
cos a = 0.75
a = 41.4°
ab = a/cos a = 1.5/cos41.4
ab = 1.5/0.75
ab = 2
b = 2 × sin 41.4
b = 2 × 0.66
b = 1.32
Therefore, the IC will be (0, 1.32).
Learn more about lengths on:
https://brainly.com/question/2217700
#SPJ1
51.
What is a subpanel?
Answer:
im pretty sure its answer D
Explanation:
If a 1500 V load is ac coupled to the output in Figure 9–60, what is the resulting output voltage (rms) when a 50 mV rms input is applied? gm = 5000 mS.
The resulting output voltage (rms) when a 50 mV rms input applied is -187.5 mV.
What is rms voltage?Root Mean Square Voltage is the amount of AC power which produces the same heating effect as DC Power would have produced.
Vo = -gm x Vi (Rd II Rl )
Vo = -5000 x 10⁻⁶ x 50 x 10⁻³ x (1.5k II 1.5k )
Vo = -25 x 10⁻² x 750 x 10⁻³
Vo = -187.5 mV
Hence, resulting output voltage (rms) when a 50 mV rms input applied is -187.5 mV.
Learn more about rms voltage.
https://brainly.com/question/13507291
#SPJ1
Why are manhole covers round in most of the cases?
Answer:
Explanation:
Because there are no angles for alignment, the round shape makes these heavy covers easier to put back on once they're taken off. Round covers are also easier to manufacture. But the main reason manhole covers are round is so they won't accidentally fall into the manhole itself.
the most important element in the regulation of the hts is the
Answer:
Explanation:
the driver who obeys traffic laws
What are the rigging devices used to move loads such as steel plates and sheet piles without the use of slings, but grip the load by biting down and using jaw tension to secure the load
The rigging device which are used to move loads without the use of slings, but grip the load by biting down and using jaw tension to secure the load, is lifting clamps.
What are the rigging devices?The rigging devices are used to lift the objects and items when the safety is required. This device is used in the industries.
Types of rigging devices
Rigging hooks-These rigging device is used when the heavy load need to be lift.Lifting clamps-Lifting clamp are used to lift the device with jaw tension to secure the load. In this, there is no use of slings.Pulley and blocks-In the load is lifts with the help of block and pulley arrangement. This is a widely used rigging device.Thus, the rigging device which are used to move loads without the use of slings, but grip the load by biting down and using jaw tension to secure the load, is lifting clamps.
Learn more about the rigging devices here;
https://brainly.com/question/8430576
#SPJ1
The team needs to choose a primary view for the part drawing. Three team members make suggestions:
- Team member 1 suggests an orthographic top view because that is how the plans for the part were submitted.
- Team member 2 suggests an isometric view showing side details that were documented within the submitted plans.
- Team member 3 suggests all three orthogonal views should be presented as the primary view.
What is the best way to proceed?
Answer choices below:
Answer:
Option 1
Explanation:
As the team has already submitted the plans for the part drawing, the best way to proceed would be how it was given in the plans. Hence, the option to be selected :
Team member 1 suggests an orthographic top view because that is how the plans for the part were submitted.Answer:
The first option
Explanation:
Team member 1 suggests an orthographic top view because that is how the plans for the part were submitted.
A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress in the tube when the power is transmitted through a 4: 1 gearing.
The maximum shear stress in the tube when the power is transmitted through a 4: 1 gearing is 28.98 MPa.
What is power?Power is the energy transferred per unit time.
Torque is find out by
P = 2πNT/60
10000 = 2π x 2000 x T / 60
T =47.74 N.m
The gear ratio Ne / Ns =4/1
Ns =2000/4 = 500
Ts =Ps x 60/(2π x 500)
Ts =190.96 N.m
Maximum shear stress τ = 16/π x (T / (d₀⁴ - d₁⁴))
τ max =T/J x D/2
where d₁ = 30mm = 0.03 m
d₀ = 30 +(2x 4) = 38mm =0.038 m
Substitute the values into the equation, we get
τ max = 16 x 190.96 x 0.038 /π x (0.038⁴ - 0.03⁴)
τ max = 28.98 MPa.
Thus, the maximum shear stress in the tube is 28.98 MPa.
Learn more about power.
https://brainly.com/question/13385520
#SPJ1
250 volts are applied to a toaster oven which draws a current of 12 A.
What is the toaster oven's resistance?
Answer:
20.833 ohms
Explanation:
V = IR re-arrange
V/I = R
250 / 12 = 20.833 ( 20 5/6)
True or false?Inventory-risk costs are a form of carrying costs.
or...................
Answer:
i believe it is true
Explanation:
A continuous fiber-reinforced composite is to be produced by dispersing 60 vol% carbon fibers in a polycarbonate matrix. if the stress in the polycarbonate matrix when the carbon fibers fail is 45 mpa, the longitudinal elastic modulus of the composite using rule of mixture is
Answer:
Explanation:
A continuous fiber-reinforced composite is to be produced by dispersing 60 vol% carbon fibers in a polycarbonate matrix. if the stress in the polycarbonate matrix when the carbon fibers fail is 45 mpa, the longitudinal elastic modulus of the composite using rule of mixture
Which component of the enterprise platform will help the company capture, curate, and consume customer information to improve their services?
Data and insight is the component of the enterprise platform will help the company capture customer information.
What is Data and insight?
These are the data and knowledge gotten from analysis of customer's information in a business.
This enterprise platform is very important as it helps the organization to improve their services
Read more about Data and insight here https://brainly.com/question/2889076
#SPJ1
what would it be like if all your friends were exactly the same
Answer:
Boring, since they would have the same personality, name, and occupation... it would be like doing the same thing every day or always talking to the same person. It would be impossible to figure out who is who since their looks would be the same as well. Although they might be fun to hang around with them if they had the same humor as you, or liked doing the same activities.
Explanation:
hope this helps:)
A group of friends that are identical in every manner would prevent opportunities for personal development and learning, but having friends with similar interests and values might foster a feeling of community and shared experiences.
Thus, Lack of diversity would limit opportunities for new viewpoints, original ideas, and varied experiences. There might not be enough intellectual and emotional stimulation and repetitious conversations and exchanges.
Because everyone would address problems and obstacles in the same way, life might become predictable and static.
Although conflicts and disagreements may be less frequent, the lack of diverse opinions may make it more difficult to come up with original solutions.
Thus, A group of friends that are identical in every manner would prevent opportunities for personal development and learning, but having friends with similar interests and values might foster a feeling of community and shared experiences.
Learn more about Learning, refer to the link:
https://brainly.com/question/1503472
#SPJ3
if you were to create your own watershed using materials from your house, what materials would you need, and why would you need these materials to create a watershed?
Answer:
A pan (baking)
Newspaper
Cloth
(colored) Water
A binder (to elevate one side of the pan)
Explanation:
hope this helps:)
8. A voltmeter measures a voltage drop of 600 V across a heating element while an
ammeter reads the current through it as 2.0 A. What is the resistance of the
heating coil.
Answer:
How do I calculate voltage drop?
To calculate voltage drop, E, across a component, you need to know the resistance of the component and the current thru it. Ohm's Law is E=I⋅R , which tells us to then multiply I by R . E is the voltage across the component also known as voltage drop
Explanation:
Which of the following is defined as the progression of Ideas leading to the final delivery of a product?
O design
O feasibility
O schematics
O optimization
The progression of ideas leading to the final delivery of a product is in option D optimization.
What is optimization?Optimization means upgrading something or making it best. The process of making the best effective use of a situation or resource.
Hence, if the product is going to shape to its final form, then it will go through the process of optimization.
Hence, option D is true.
Learn more about optimization here,
https://brainly.com/question/14914110
#SPJ1
Blank is common during exercise.
Answer:
Sweat
Explanation:
As you exercise you respire and warm up due to energy. In turn, two things happen, blood vessels vasodilate (irrelevant to you) and sweat glands sweat more. this sweat then evaporates and cools down the body.
Answer:
Hyperpnea is common during exercise
Explanation:
Edge 2023
Please let me know the answer up to three decimals
Answer: 00.9666
Explanation: I don't know if this is the correct answer but, this question should've been under "Mathematics" and not under "Engineering" hope this helps. Have a good day/night ^^
Help me plss... :‹
[tex] \: \: \: [/tex]
Answer: You're question is very vague... be more specific in the problem, what is it asking you to do?
Explanation: This shouldn't be under "Engineering" you should put it under "Mathematics" for a better result. Sorry for the mix up! Hope this helps! ^^
Is it possible to create an iron man suit if yes what do i need to build it
Answer: Money, Jesus, Metal, and an infinity stone gold-titanium alloy.
Explanation: yes