The correct option (c). Three coats of mud with tape 4", 6" and then 8-12" knives.
Level 5 taping provides a very smooth surface by three coats of mud with tape 4", 6" and then 8-12" knives.
The Level 5 Taping process involves covering the entire surface of the wallboard with three separate coats of joint compound.
The first coat of joint compound is used to embed the tape and eliminate any bubbles or wrinkles in the tape. For the second coat, the drywall contractor uses a six-inch joint knife to apply a thin layer of joint compound over the tape.
This coat should be allowed to dry completely.
The third and final coat is where the smoothness comes in. This coat involves using an eight to twelve-inch joint knife to apply a thin layer of joint compound over the entire surface of the wallboard.
This coat should be allowed to dry completely. After the third coat is completely dry, the wallboard is sanded smooth, and the dust is removed before the primer and paint are applied.
To know more about coats visit:
https://brainly.com/question/2750661
#SPJ11
12.5% 1- A three story concrete moment resisting frame (MRF) is shown below. The lateral seismic base shear force was calculated using the ELF procedure and found to be 68 kips as indicated. w = 80 kips Roof 12 w = 125 kips 3rd Floor 12 w = 135 kips 2nd Floor 15 1st Floor V-68 kips Elevation a) Calculate the lateral force at the first floor of the building b) Calculate the story shear at the second story of the building c) Calculate the allowable drift for the third story
a) The lateral force at the first floor of the building is 68 kips.
The lateral force at each floor of a building can be calculated by multiplying the floor weight (w) by the seismic coefficient.The seismic coefficient is a factor that accounts for the building's response to seismic forces and is typically determined using seismic design codes or guidelines.b) The story shear at the second story of the building is 135 kips.
Story shear is the force that acts on each story of a building due to lateral seismic forces.The story shear can be calculated by multiplying the floor weight (w) by the seismic coefficient at that particular story.c) The allowable drift for the third story needs more information to be calculated.
The allowable drift is a measure of the maximum displacement or movement a building can undergo during an earthquake.It depends on various factors such as the building's structural system, occupancy type, and design criteria.Without specific information about the building's structural system and design criteria, it is not possible to determine the allowable drift for the third story.The lateral force at the first floor is 68 kips, the story shear at the second story is 135 kips, and the allowable drift for the third story cannot be determined without additional information.
Learn more about Lateral :
https://brainly.com/question/12506372
#SPJ11
In circle U, UV = 12 and the length of VW 12 and the length of VW = 87. Find m/VUW.
Finally, taking the inverse cosine ([tex]cos^{-1[/tex]) of both sides, we can find the measure of angle VUW (θ):
m/VUW = [tex]cos^{-1(-0.6875)[/tex]
To find the measure of angle VUW (m/VUW), we can use the properties of a circle and the given information.
In circle U, UV is a radius of length 12 units. Since VW is also a radius of the same circle, it will have the same length of 12 units. Therefore, we have a triangle UVW with UV = VW = 12 units.
To find the measure of angle VUW, we can use the Law of Cosines. In this case, we have a triangle with sides of length 12, 12, and 87. Let's denote angle VUW as θ.
Applying the Law of Cosines, we have:
[tex]87^2 = 12^2 + 12^2[/tex] - 2 x 12 x 12 x cos(θ)
Simplifying the equation:
7569 = 144 + 144 - 288 x cos(θ)
7569 = 288 - 288 x cos(θ)
Dividing both sides by 288:
26.3125 = 1 - cos(θ)
Subtracting 1 from both sides:
-0.6875 = -cos(θ)
Finally, taking the inverse cosine ([tex]cos^{-1[/tex]) of both sides, we can find the measure of angle VUW (θ):
m/VUW = [tex]cos^{-1(-0.6875)[/tex]
The resulting value of [tex]cos^{-1(-0.6875)[/tex] will give us the measure of angle VUW in radians or degrees, depending on the unit of measurement used.
For more such answers on Radians
https://brainly.com/question/29058626
#SPJ8
Show that cos360∘=(cos180∘)2−(sin180∘)^2 by evaluating both the left and right hand sides.
$\cos 360^\circ = \cos^2 180^\circ - \sin^2 180^\circ$
What is the value of $\cos 360^\circ$?To find the value of $\cos 360^\circ$, we need to evaluate both sides of the given equation and show that they are equal.
Left Hand Side (LHS):
Using the periodicity of the cosine function, we know that $\cos 360^\circ$ is equal to $\cos 0^\circ$. The cosine of 0 degrees is 1, so LHS = $\cos 0^\circ = 1$.
Right Hand Side (RHS):
Let's evaluate the RHS of the equation step by step. We know that $\cos 180^\circ = -1$ and $\sin 180^\circ = 0$. Substituting these values into the equation, we get:
RHS = $\cos^2 180^\circ - \sin^2 180^\circ = (-1)^2 - 0^2 = 1 - 0 = 1$.
Since both the LHS and RHS evaluate to 1, we can conclude that $\cos 360^\circ = \cos^2 180^\circ - \sin^2 180^\circ$.
Learn more about value
brainly.com/question/30145972
#SPJ11
Suppose, a rose is 15 taka, a tuberose is 9 taka, and a marigold is 6 taka. John's father gives him 100 taka to buy each type of flower. John buys some flowers and tells his father that they cost exactly 100 taka. Determine whether John is lying or not. [Note: Fraction of a flower cannot be bought]
John is lying because he claimed he spent exactly 100 taka, but he only spent 45 taka, which is less than half of the 100 taka he was given.
Suppose, a rose is 15 taka, a tuberose is 9 taka, and a marigold is 6 taka. John's father gives him 100 taka to buy each type of flower. John buys some flowers and tells his father that they cost exactly 100 taka. Determine whether John is lying or not.
Fraction of a flower cannot be bought]John can buy only one of each type of flower, since fractions of a flower cannot be bought.
The cost of one rose is 15 taka, the cost of one tuberose is 9 taka, and the cost of one marigold is 6 taka.
John spent 30 taka on roses, 9 taka on tuberose, and 6 taka on marigold, for a total of 45 taka.
Since John claimed he spent exactly 100 taka and he spent only 45 taka, John is lying.
In this scenario, John is lying because he claimed he spent exactly 100 taka, but he only spent 45 taka, which is less than half of the 100 taka he was given.
To know more about taka visit:
https://brainly.com/question/12017701
#SPJ11
Calculate the parts per million concentration of fluoride ion in a 666 g water sample that contains 0.460mg of fluoride. Question 5 Express 0.0406% W/W concentration as ppm.
The concentration of fluoride ion in the water sample is approximately 0.690 ppm. The concentration of 0.0406% w/w is equivalent to 4.06 ppm.
To calculate the parts per million (ppm) concentration of fluoride ion in the water sample, we need to determine the amount of fluoride ion in the sample and express it relative to the total mass of the sample.
Mass of water sample = 666 g
Mass of fluoride = 0.460 mg
First, we need to convert the mass of fluoride from milligrams to grams:
0.460 mg = 0.460 × 10^(-3) g
Now, we can calculate the ppm concentration of fluoride ion:
ppm = (mass of fluoride / mass of water sample) × 10^6
ppm = (0.460 × 10^(-3) g / 666 g) × 10^6
= (0.460 × 10^(-3) / 666) × 10^6
≈ 0.690 ppm
Therefore, the concentration of fluoride ion in the water sample is approximately 0.690 ppm.
For the second question, to express 0.0406% w/w concentration as ppm, we simply multiply it by 10,000.
0.0406% = 0.0406 × 10^(-2) = 0.406 × 10^(-4)
ppm = (0.406 × 10^(-4)) × 10,000
= 4.06 ppm
Therefore, the concentration of 0.0406% w/w is equivalent to 4.06 ppm.
Learn more about concentration at https://brainly.com/question/31047019
#SPJ11
A 9 ft slide will be installed on a playground. The top of the slide will be 7 ft above the ground. What angle does the slide make with the ground? Enter your answer in the box. Round your final answer to the nearest degree.
The angle that the slide makes with the ground is approximately 40.6 degrees when rounded to the nearest degree.
To find the angle that the slide makes with the ground, we can use basic trigonometric principles.
In this case, we have a right triangle formed by the slide, the ground, and a vertical line connecting the top of the slide to the ground.
The height of the slide is given as 7 ft, and the length of the slide is given as 9 ft.
We can use the trigonometric function tangent (tan) to calculate the angle.
The tangent of an angle is defined as the ratio of the opposite side to the adjacent side in a right triangle.
In this case, the opposite side is the height of the slide (7 ft), and the adjacent side is the length of the slide (9 ft).
Using the formula for tangent, we can calculate the angle:
tan(angle) = opposite/adjacent
tan(angle) = 7/9
To find the angle, we need to take the inverse tangent (arctan) of this ratio:
angle = arctan(7/9)
Using a calculator or a trigonometric table, we can find the angle to be approximately 40.6 degrees.
For similar question on right triangle.
https://brainly.com/question/2217700
#SPJ8
Consider the binomial 20xy ^2
−75x ^3
. When completely factored over the set of integers, which of the following are its factors? Select all that apply. Select one or more: 2y+5x 4y+5x 5x 5y 2y=5x 4y−5x
The given binomial expression is 20xy² - 75x³. We need to factorize it completely over the set of integers.The greatest common factor (GCF) of the terms in the given binomial expression is 5x.
Therefore,
5x(4y·y - 15x²)5x(2y - 5x)(2y + 5x)
Therefore, 5x, 2y - 5x, and 2y + 5x are the factors of the given binomial expression when it is completely factored over the set of integers. The given binomial expression is 20xy² - 75x³. We need to factorize it completely over the set of integers. Factorization over integers of a binomial expression is the process of factoring out the greatest common factor (GCF) of its terms and the resulting trinomial obtained is factorized using the appropriate factoring methods. The GCF of 20xy² and -75x³ is 5x. Therefore, we can write
20xy² - 75x³ = 5x(4y·y - 15x²)
The expression 4y·y - 15x² can be further factorized. We can use the following rule:(a + b)·(a - b) = a² - b²Here, a is 2y and b is 5x. Therefore, 4y·y - 15x² can be written as (2y)² - (5x)². Therefore, we have
4y·y - 15x² = (2y)² - (5x)² = (2y + 5x)·(2y - 5x)
Therefore, we can substitute this in the expression 20xy² - 75x³ as follows:
20xy² - 75x³ = 5x(4y·y - 15x²)= 5x(2y + 5x)·(2y - 5x)
Therefore, 5x, 2y - 5x, and 2y + 5x are the factors of the given binomial expression when it is completely factored over the set of integers. Hence, the answer is 5x, 2y - 5x, and 2y + 5x.
Therefore, the factors of the binomial 20xy² - 75x³ when completely factored over the set of integers are 5x, 2y - 5x, and 2y + 5x.
To learn more about Factorization visit:
brainly.com/question/24182713
#SPJ11
What can be concluded about the values of ΔH and ΔS from this graph? (A) △H>0,ΔS>0 (B) ΔH>0,ΔS<0 (C) △H<0,ΔS>0 (D) ΔH<0,ΔS<0
In thermodynamics, ΔH is the difference in enthalpy between the products and reactants of a chemical reaction. The symbol ΔS denotes the entropy difference between the products and reactants.
The entropy change and enthalpy change of a chemical reaction can be determined from a graph of Gibbs energy versus reaction advancement. ΔH and ΔS from the graph is the equation that must be used, which is:ΔG = ΔH - TΔS where ΔG is the change in Gibbs energy, T is temperature, ΔH is the change in enthalpy, and ΔS is the change in entropy.
Using this equation, the following conclusion can be made from the graph:If the reaction is exothermic, The entropy change and enthalpy change of a chemical reaction can be determined from a graph of Gibbs energy versus reaction advancement. the ΔH value will be negative, and if the entropy of the system increases, the ΔS value will be positive. As a result, the correct answer is (C) ΔH < 0, ΔS > 0.
To know more about products visit:
https://brainly.com/question/32553819
#SPJ11
For an 85 wt.% Pb-15 wt.% Mg alloy, make schematic sketches of the microstructure that would be observed for conditions of very slow cooling at 600°C, 500°C, 270°C, and 200°C. Label all phases and indicate their approximate compositions.
The actual microstructure can be influenced by factors such as cooling rate, impurities, and other alloying elements. For an 85 wt.% Pb-15 wt.% Mg alloy, the microstructure observed during slow cooling at different temperatures can be schematically represented as follows:
1. At 600°C:
- The microstructure consists of a single phase, which is a solid solution of lead (Pb) and magnesium (Mg).
- The approximate composition of this phase is 85 wt.% Pb and 15 wt.% Mg.
2. At 500°C:
- The microstructure still consists of a single phase, which is a solid solution of lead (Pb) and magnesium (Mg).
- The approximate composition of this phase remains the same at 85 wt.% Pb and 15 wt.% Mg.
3. At 270°C:
- The microstructure starts to show the formation of a second phase known as the eutectic phase.
- The eutectic phase is a mixture of lead (Pb) and magnesium (Mg) in a specific ratio.
- The approximate composition of the eutectic phase is determined by the eutectic composition of the alloy, which occurs at 61.9 wt.% Pb and 38.1 wt.% Mg.
- The remaining phase still consists of the solid solution with an approximate composition of 85 wt.% Pb and 15 wt.% Mg.
4. At 200°C:
- The microstructure further develops the eutectic phase, which starts to increase in volume.
- The approximate composition of the eutectic phase remains the same at 61.9 wt.% Pb and 38.1 wt.% Mg.
- The solid solution phase reduces in volume and has an approximate composition of 85 wt.% Pb and 15 wt.% Mg.
It's important to note that these sketches represent the general microstructural changes that occur during slow cooling for an 85 wt.% Pb-15 wt.% Mg alloy. The actual microstructure can be influenced by factors such as cooling rate, impurities, and other alloying elements.
To know more about Microstructure visit:
https://brainly.com/question/31789619
#SPJ11
A certain reaction has an activation energy of 26.09 kJ/mol. At
what Kelvin temperature will the reaction proceed 4.50 times faster
than it did at 357 K?
The temperature at which the given reaction will proceed 4.50 times faster than it did at 357 K is 451.23 K.
We have to determine the temperature (in Kelvin) at which the given reaction will proceed 4.50 times faster than it did at 357 K given that the reaction has an activation energy of 26.09 kJ/mol.The rate constant, k is given by the Arrhenius equation as:k = Ae^(-Ea/RT)where:
k = rate constant
A = pre-exponential factor or frequency factor
e = base of natural logarithm
Ea = activation energy
R = gas constant
T = temperature in Kelvin Rearrange the equation to get the ratio of rate constants:
k1/k2 = (Ae^(-Ea/RT1)) / (Ae^(-Ea/RT2))Cancel out the pre-exponential factor,
A:k1/k2 = e^(-Ea/R) x (1/T1 - 1/T2)
Let k1 and k2 be the rate constants at temperatures T1 and T2 respectively. We have to solve for T2 given that k2 = 4.50k1 and T1 = 357 Substituting the values:
k1/(4.50k1) = e^(-26.09/(8.314 x 357) x (1/357 - 1/T2))1/4.50
= e^(-7.02 x 10^-4 x (1/357 - 1/T2))
Taking the natural logarithm of both sides, we get:
-ln(4.50) = -7.02 x 10^-4 x (1/357 - 1/T2)T2
= 357 / (1 + (4.50 x e^(-ln(4.50)/7.02 x 10^-4)))
= 451.23 K
To know more about reaction visit:-
https://brainly.com/question/30464598
#SPJ11
4-5 Determine the design compressive strength for the HSS 406.4x6.4 section of steel with F, = 345 MPa. The column has the same effective length in all directions Le = 8 m.
The design compressive strength for the HSS 406.4 × 6.4 section of steel with Fy = 345 MPa is 94.7 kN.
The effective length factor K for a sway frame with sway restrained at the top of the column, according to AISC Specification Section C₃.₂, is given by the following equation:
K = [1 + (Cr / Cv) × (Lb / ry) × √(Fy / E))]²
where Lb is the unbraced length of the member in the plane under consideration
Cr is the critical load factor
Cv is the coefficient of variation for the axial load capacity of the column
ry is the radius of gyration in the plane of buckling of the member
Fy is the yield strength of the member in tension
E is the modulus of elasticity of steel
The critical load factor, according to AISC Specification Section E7, is as follows:
[tex]Cr=\pi^2*E/ (Kl/r)^2[/tex]
where Kl/r is the effective length factor,
which is calculated as follows: Kl/r = K × Lb / ry
For a hollow structural section (HSS), the radius of gyration can be calculated as follows:
ry = √[(Iy + Iz) / (A/4)]
where Iy and Iz are the second moments of area about the major and minor axes, respectively, and A is the cross-sectional area.
The design compressive strength for an HSS section is calculated as follows:
[tex]P_n=\phi\times P_{nominator}[/tex]
[tex]\phi[/tex] = 0.90 for axial compression
[tex]P_{nominator}[/tex] = Ag × Fy × Kd
where Ag is the gross cross-sectional area of the member
Fy is the specified minimum yield strength of the member
Kd is the effective length factor for the member in compression
The effective length factor K for the HSS section can be determined using the above equation:
K = [1 + (Cr / Cv) × (Lb / ry) × √(Fy / E))]²
where
Lb = Le
= 8 mCr
= pi² × E / (Kl/r)²Kl/r
= K × Lb / ryry = √[(Iy + Iz) / (A/4)]
[tex]P_{nominator}[/tex] = Ag × Fy × KdKd can be found in AISC Specification Table B₄.₁ for various HSS shapes and bracing conditions.
For the HSS 406.4 × 6.4 section, the appropriate value of Kd is 0.85. The cross-sectional area of the HSS 406.4 × 6.4 section can be calculated using the outside diameter (OD) and wall thickness (t) as follows:
A = (OD - 2 × t)² / 4 - (OD - 2 × t - 2 × t)² / 4Ag
= A - 2 × (OD - 2 × t - 2 × t) × t
Substituting the values of the various parameters and simplifying:
[tex]P_{nominator}[/tex] = Ag * Fy * Kd
= [360.8 mm² × 345 MPa × 0.85] / 1000
= 105.2 kN
The design compressive strength of the HSS 406.4 × 6.4 section is given by:
[tex]P_n=\phi\times P_{nominator}[/tex]
= 0.90 * 105.2 kN
= 94.7 kN
Therefore, the design compressive strength for the HSS 406.4 × 6.4 section of steel with Fy = 345 MPa is 94.7 kN.
To know more about cross-sectional area, visit:
https://brainly.com/question/13029309
#SPJ11
please help i’ll give 20 points
Answer:
E
Step-by-step explanation
[tex]\sqrt{3-2x}[/tex] = [tex]\sqrt{2x}[/tex] + 1
square both sides to clear the radicals
([tex]\sqrt{3-2x}[/tex] )² = ([tex]\sqrt{2x}[/tex] + 1)²← expand using FOIL
3 - 2x = 2x + 2[tex]\sqrt{2x}[/tex] + 1 ( subtract 2x + 1 from both sides )
- 4x + 2 = 2[tex]\sqrt{2x}[/tex] ( divide through by 2 )
- 2x + 1 = [tex]\sqrt{2x}[/tex] ( square both sides )
(- 2x + 1)² = 2x ← expand left side using FOIL
4x² - 4x + 1 = 2x ( add 4x to both sides )
4x² + 1 = 6x ( subtract 1 from both sides )
4x² = 6x - 1
Time left 1.0 5. Calculate the Vertical reaction of support A Take E as 10 kN, G as 5 kN, H as 3 kN. also take Kas 8 m, L as 3 m, Nas 13 m. 5 MARKS HEN H EKN HEN T 16 Km GEN F Lm A B ID Nim Nm Nm Nm
The vertical reaction of support A is approximately 12.6 kN.
What is the vertical reaction at support A in kN?Step 3: To calculate the vertical reaction at support A, we need to consider the equilibrium of forces. Given that E is 10 kN, G is 5 kN, H is 3 kN, Kas is 8 m, L is 3 m, and Nas is 13 m, we can determine the vertical reaction at support A.
First, let's calculate the moment about support A due to the applied loads:
Moment about A = E * Kas + G * (Kas + L) + H * (Kas + L + Nas)
Substituting the given values:
Moment about A = 10 kN * 8 m + 5 kN * (8 m + 3 m) + 3 kN * (8 m + 3 m + 13 m)
= 80 kNm + 55 kNm + 96 kNm
= 231 kNm
Next, let's consider the equilibrium of forces in the vertical direction:
Vertical reaction at A = (E + G + H) - (Moment about A / L)
Substituting the given values:
Vertical reaction at A = (10 kN + 5 kN + 3 kN) - (231 kNm / 3 m)
= 18 kN - 77 kN
= -59 kN
Since the vertical reaction at support A is typically positive for upward forces, we take the absolute value:
Vertical reaction at A ≈ |-59 kN| ≈ 59 kN
Therefore, the vertical reaction at support A is approximately 59 kN.
Learn more about vertical reaction
https://brainly.com/question/3132810
SPJ11
Which hydraulic structure is used when lower discharges are desired for a given head? Group of answer choices
a) V-notch weir
b)Parshall flume Broad-crested
c)rectangular weir
d)Contracted weir
The hydraulic structure that is used when lower discharges are desired for a given head is called contracted weir.
A weir is a barrier across a river that obstructs the flow of water.
A weir is a hydraulic structure designed to change the characteristics of flowing water to make it more useful.
Weirs are utilized to create a more regular flow of water to enable irrigation and water supply, protect the banks of rivers, and manage erosion.
A contracted weir is a rectangular structure constructed over the river's bed, where water flows through a narrow opening.
Water can flow under gravity through an opening (notch or a thin-plate), called a weir opening or notch, placed across an open channel or a pipe.
The correct answer is d) Contracted weir.
To know more about contracted weir visit:
https://brainly.com/question/32722065
#SPJ11
The vector parametric equation for the line through the points (1,2,4) and (5,1,−1) is L(t)=
The vector parametric equation for the line through the points (1,2,4) and (5,1,−1) is given by L(t) = (1, 2, 4) + t(4, -1, -5).
To find the vector parametric equation for a line, we need a point on the line and a direction vector. The given points (1,2,4) and (5,1,−1) can be used to determine the direction vector. Subtracting the coordinates of the first point from the second point, we get (5-1, 1-2, -1-4) = (4, -1, -5). This direction vector represents the change in x, y, and z coordinates as we move along the line. Now, we can write the vector parametric equation using the point (1,2,4) as the initial position and the direction vector (4, -1, -5). Adding the direction vector scaled by a parameter t to the initial point, we obtain L(t) = (1, 2, 4) + t(4, -1, -5).
This equation represents the line passing through the points (1,2,4) and (5,1,−1), where t is a parameter that allows us to obtain different points on the line by varying its value.
To learn more about vector refer:
https://brainly.com/question/15519257
#SPJ11
Consider an opaque horizontal plate that is well insulated on its back side. The irradiation on the plate is 2500 W/m² of which 500 W/m² is reflected. The plate is at 227° C and has an emissive power of 1200 W/m². Air at 127° C flows over the plate with a heat transfer of convection of 15 W/m² K. Given: -8 W Oplate = 5.67x10-8 Determine the following: Emissivity, . Absorptivity. Radiosity of the plate. . What is the net heat transfer rate per unit area? m²K4
The emissivity of the plate is 0.82. The absorptivity of the plate is 0.8. The radiosity of the plate is 2000 W/m². The net heat transfer rate per unit area is 296.2 W/m².
Given,The irradiation on the plate = 2500 W/m²
Reflected radiation = 500 W/m²
The plate temperature = 227°C
Emissive power of the plate = 1200 W/m²
Heat transfer coefficient = 15 W/m² K
Stefan–Boltzmann constant = 5.67 × 10⁻⁸ W/m²K⁴
Emissivity of the plate is given by
ε = Emissive power of the plate/Stefan–Boltzmann constant * Temperature⁴
= 1200/ (5.67 × 10⁻⁸) * (227 + 273)⁴
= 0.82
Absorptivity is given bya = Absorbed radiation / Incident radiation
= (Irradiation on the plate – Reflected radiation) / Irradiation on the plate
= (2500 – 500) / 2500
= 0.8
The radiosity of the plate is given by
J = aI
= 0.8 × 2500
= 2000 W/m²
The rate of heat transfer due to convection per unit area can be calculated using the relation.
q_conv = h × (T_surface – T_air)
= 15 × (227 – 127)
= 1500 W/m²
Now the net rate of heat transfer per unit area is given by,
q_net = aI – εσT⁴ – q_conv
= 0.8 × 2500 – 0.82 × 5.67 × 10⁻⁸ × (227 + 273)⁴ – 1500
= 296.2 W/m²
Know more about the emissivity
https://brainly.com/question/29485098
#SPJ11
A distilling column is fed with a solution containing 0.45 mass fraction of benzene and 0.55 mass fraction of toluene. If 85% of the benzene in the feed must appear in the overhead product, while 81% of the toluene in the feed is in the residue, what is the mass fraction of toluene in the residue?
Mass fraction of toluene in the residue is 60.6%.The mass fraction of toluene in the residue of the solution fed to a distilling column can be calculated using the following formula:
Mass fraction of toluene in the residue = Mass of toluene in the residue / Mass of residue.
Let the feed solution to the column contain 100 g of the solution. Given,The solution contains 0.45 mass fraction of benzene and 0.55 mass fraction of toluene.85% of the benzene in the feed must appear in the overhead product.81% of the toluene in the feed is in the residue.
Mass of benzene fed to the column = 0.45 × 100 g ⇒45 g
Mass of toluene fed to the column = 0.55 × 100 g ⇒ 55 g
Mass of benzene in the overhead product = 0.85 × 45 g ⇒ 38.25 g
Therefore, Mass of benzene in the residue = 45 - 38.25 ⇒ 6.75 g
Mass of toluene in the residue = 55 - (55 × 0.81) ⇒ 10.45 g
Mass of residue = Mass of benzene in the residue + Mass of toluene in the residue= 6.75 g + 10.45 g ⇒ 17.2 g
Mass fraction of toluene in the residue = (10.45 / 17.2) × 100%
= 60.6%.
Therefore, Mass fraction of toluene in the residue is 60.6%.
To know more about Mass fraction visit-
brainly.com/question/31961780
#SPJ11
50. The game board jeopardy is divided into 30 squares. There are six categories and five
levels. In the Double Jeopardy round there are two daily doubles. What are the odds of
choosing a daily double on the first pick?
A. 1:13
B. 1:14
C. 1:15
D. 1:16
Answer:
c
Step-by-step explanation:
A dealer sold a car to Derek for $4200 down and end-of-month payments of $588 for 5.5 years, including interest at 3.13% compounded annually. What was the selling price of the car? a. $7129.15 b. $35651.23 c. $39851.23 d. $11853.23
To find the selling price of the car, we need to add the present value of the end-of-month payments and the down payment. Using the formula for the present value of an annuity, we get $39851.23 (option C) as the selling price.
To find the selling price of the car, we need to use the formula for the present value of an annuity. An annuity is a series of equal payments made at regular intervals. In this case, the annuity is the end-of-month payments of $588 for 5.5 years. The formula for the present value of an annuity is:
[tex]PV = PMT \cdot \left[\frac{{1 - \frac{1}{{(1 + i)^n}}}}{i}\right][/tex]
where PV is the present value, PMT is the payment amount, i is the interest rate per period, and n is the number of periods.
In this case, we have:
PV = ?
PMT = 588
i = 0.0313 / 12 (since the interest rate is compounded annually and the payments are made monthly)
n = 5.5 * 12 (since there are 12 months in a year and the payments are made for 5.5 years)
Substituting these values into the formula, we get:
[tex]PV = 588 \cdot \left[\frac{{1 - \frac{1}{{(1 + \frac{{0.0313}}{{12}})^{(5.5 \cdot 12)}}}}}{{\frac{{0.0313}}{{12}}}}\right][/tex]
PV = 35651.23
This means that the present value of the end-of-month payments is $35651.23. However, this is not the selling price of the car yet. We also need to add the down payment of $4200 that Derek paid at the beginning. So, the selling price of the car is:
Selling price = PV + down payment
Selling price = 35651.23 + 4200
Selling price = 39851.23
Therefore, the selling price of the car is $39851.23. The correct answer is c) $39851.23.
Learn more about present value at:
https://brainly.com/question/30390056
#SPJ11
Annie buys some greeting cards. Each card costs
$
1
She pays with a twenty-dollar bill. Let
n
represent the number of greeting cards Annie buys. Write an expression that represents the amount of change Annie should receive.
Answer:
19
Step-by-step explanation:
Because 20-1=19
A current of 7.53×10 4A is passed through an electrolysis cell containing molten KCl for 18.8 days. (a) How many grams of potassium are produced
Therefore, approximately 246.23 grams of potassium are produced in the given electrolysis process.
To calculate the grams of potassium produced, we need to use Faraday's law of electrolysis, which states that the amount of substance produced at an electrode is directly proportional to the quantity of electricity passed through the cell. The formula is:
Mass (g) = (Current (A) * Time (s) * Molar Mass (g/mol)) / (Faraday's Constant (C/mol))
Given:
Current = 7.53 × 10⁴ A
Time = 18.8 days = 18.8 * 24 * 60 * 60 seconds
Molar Mass of Potassium (K) = 39.10 g/mol
Faraday's Constant = 96,485 C/mol
Now we can plug in these values to calculate the mass of potassium produced:
Mass = (7.53 × 10⁴ A * 18.8 * 24 * 60 * 60 s * 39.10 g/mol) / (96,485 C/mol)
Mass ≈ 246.23 g
To know more about electrolysis process,
https://brainly.com/question/14967237
#SPJ11
When 3(x-k)/w=4 is solved for x in terms of w and k, it’s solution is which of the following? Show the algebraic manipulations you used to get your answer
The solution to the equation is x = (4w + 3k) / 3.
To solve the equation 3(x - k) / w = 4 for x in terms of w and k, we can follow these algebraic manipulations:
Multiply both sides of the equation by w to eliminate the fraction:
3(x - k) = 4w
Expand the left side by distributing 3:
3x - 3k = 4w
Add 3k to both sides of the equation to isolate the term with x:
3x = 4w + 3k
Divide both sides by 3 to solve for x:
x = (4w + 3k) / 3
Therefore, the solution to the equation is x = (4w + 3k) / 3.
for such more question on equation
https://brainly.com/question/17482667
#SPJ8
Banks have different rates for selling foreign currency or buying it. The VIP Bank advertises
its rates as follows
WE SELL
£1-16.45 Mexican Pesos
WE BUY
19.95 Mexican Pesos - £1
Daniel changes £900 into Pesos. He has to cancel his holiday and change his Pesos back into
Pounds.
There is a £3 commission charge on each exchange. What is the total loss on his money
exchange?
(4 marks)
Daniel changes £900 into pesos, he will then incur a charge of £3. This means that the amount of money he will have after the first exchange is £897 (£900 - £3). So, the answer is £165.73.
Daniel then changes this amount to pesos, this time incurring another charge of £3. The amount of money he has now in pesos is 897 x 16.45 = 14,731.65. He will then incur another charge of £3 when changing the pesos back to pounds.
After the second exchange, Daniel has: (14,731.65 ÷ 19.95) - £3 = £734.27. Therefore, the total loss on his money exchange is £900 - £734.27 = £165.73 (rounded to 2 decimal places). Answer: £165.73
For more questions on: pesos
https://brainly.com/question/29263957
#SPJ8
_______is/are the factors affecting the fatigue strength of a
steel member connection
a) no. cylcles for each stress range
b) temperature of steel in service
c) environment
d) all
All of the above factors (d) no. cycles for each stress range, temperature of steel in service, and environment affect the fatigue strength of a steel member connection.
Fatigue strength is the stress level that a material can withstand for a specified number of stress cycles before failing or breaking. The fatigue strength of a steel member connection is influenced by various factors, including:
no. cycles for each stress range The number of cycles for each stress range is a significant factor affecting the fatigue strength of a steel member connection. The fatigue life of a connection decreases as the number of cycles increases. This phenomenon is known as fatigue life reduction. The durability of a connection is inversely proportional to the number of cycles it can withstand. The number of cycles to failure decreases as the stress range increases.temperature of steel in service
The temperature of the steel in service also affects the fatigue strength of a steel member connection. High temperatures cause material properties to deteriorate, lowering the connection's fatigue strength. It is critical to maintain a low-temperature service environment to avoid material degradation.environmentThe environment in which the steel member connection is placed affects its fatigue strength. The corrosion of the connection reduces its fatigue strength. As a result, it is critical to maintain a clean and dry environment to maintain the connection's durability.All of these variables are significant in determining the fatigue strength of a steel member connection.
To know more about fatigue strength visit:
https://brainly.com/question/14034771
#SPJ11
The total cost function for a product is C(x) = 875 In(x + 10) + 1600 where x is the number of units produced. (a) Find the total cost of producing 200 units. (Round your answer to the nearest cent.) (b) Producing how many units will give total costs of $8500? (Round your answer to the nearest whole number.) _____units
(a) The total cost of producing 200 units is approximately $6103.53.
(b) Producing approximately 2641 units will result in total costs of $8500.
(a) To find the total cost of producing 200 units, we can substitute x = 200 into the cost function C(x) = 875 ln(x + 10) + 1600 and evaluate it.
C(200) = 875 ln(200 + 10) + 1600
C(200) ≈ 875 ln(210) + 1600
C(200) ≈ 875 × 5.347 + 1600
C(200) ≈ 4503.525 + 1600
C(200) ≈ 6103.525
Therefore, the total cost of producing 200 units is approximately $6103.53.
(b) To find the number of units that will result in total costs of $8500, we can set the cost function equal to $8500 and solve for x.
875 ln(x + 10) + 1600 = 8500
875 ln(x + 10) = 8500 - 1600
875 ln(x + 10) = 6900
Next, we can divide both sides of the equation by 875 and take the exponential of both sides to eliminate the natural logarithm:
ln(x + 10) = 6900 / 875
ln(x + 10) ≈ 7.8857
Taking the exponential:
e^(ln(x + 10)) ≈ e^7.8857
x + 10 ≈ 2650.579
x ≈ 2640.579
Rounding to the nearest whole number, producing approximately 2641 units will result in total costs of $8500.
Therefore, producing approximately 2641 units will give total costs of $8500.
Learn more about total cost
brainly.com/question/31443323
#SPJ11
Carbon-14 measurements on the linen wrappings from the Book of Isaiah on the Dead Sea Scrolls indicated that the scrolls contained about 79.5% of the carbon-14 found in living tissue. Approximately how old are these scrolls? The half-life of carbon-14 is 5730 years. 820 years 4,500 years 1,900 years 1,300 years 570 years
Therefore, the approximate age of these scrolls is approximately 2333 years.
To determine the approximate age of the scrolls, we can use the concept of radioactive decay and the half-life of carbon-14. Given that the scrolls contain about 79.5% of the carbon-14 found in living tissue, we can calculate the number of half-lives that have elapsed.
The number of half-lives can be determined using the formula:
Number of half-lives = ln(remaining fraction) / ln(1/2)
In this case, the remaining fraction is 79.5% or 0.795.
Number of half-lives = ln(0.795) / ln(1/2) ≈ 0.282 / (-0.693) ≈ 0.407
Since each half-life of carbon-14 is approximately 5730 years, we can calculate the approximate age of the scrolls by multiplying the number of half-lives by the half-life:
Age = Number of half-lives * Half-life
≈ 0.407 * 5730 years
≈ 2333 years
To know more about age,
https://brainly.com/question/29290729
#SPJ11
Question 3 (33 marks) (a) Find the Fourier series of the periodic function f(t)=3t², -1
the Fourier Series of the given periodic function is:
[tex]f(t) = a₀ + ∑[from n = 1 to ∞] aₙ cos(nt)[/tex]
Substituting the value of a₀ = 3, we have:
[tex]f(t) = 3 + ∑[from n = 1 to ∞] 0 cos(nt) = 3[/tex]
The Fourier series of the periodic function f(t)=3t², -1
Since the function f(t) is constant within the intervals -π ≤ t ≤ 0 and 0 ≤ t ≤ π, the integral becomes:
bₙ = (1/π) ∫[from -π to 0] 4 sin(nt) dt + (1/π) ∫[from 0 to π] -1 sin(nt) dt
Evaluating the integrals, we find:
bₙ = (1/π) [-4/n cos(nt)]∣∣[from -π to 0] - (1/π) [cos(nt)]∣∣[from 0 to π]
Simplifying, we get:
bₙ = (1/π) (4/n - 4/n - (1/n - 1/n)) = 0
Since the coefficient bₙ is zero for all values of n, the Fourier Series of f(t) consists only of the cosine terms.
Therefore,
To know more about periodic visit:
https://brainly.com/question/16061498
#SPJ11
The stack gas flowrate of a power plant is 10,000 m3/hr. Uncontrolled emissions of SO2, HCl, and HF in the stack are 1000, 300, and 100 mg/m3, respectively. The regulation states that stack gas emissions of SO2, HCl, and HF must be under 50, 10, and 1 mg/m3, respectively. Calculate the required total limestone (CaCO3) dosage (in kg/day and ton/day) to reduce SO2, HCl, and HF to the limits (MW of CaCO3: 100, SO2: 64, HCl: 36.5, and HF: 20 kg/kmol, the stoichiometric ratio for CaCO3: 1.2).
The required total limestone (CaCO3) dosage to reduce SO2, HCl, and HF emissions to the specified limits is 1,875 kg/day or 1.875 tons/day.
To calculate the limestone dosage, we need to determine the molar flow rates of SO2, HCl, and HF in the stack gas. Given the stack gas flowrate of 10,000 m3/hr and the uncontrolled emissions in mg/m3, we can convert these values to kg/hr as follows:
SO2 flow rate = 10,000 m3/hr * 1000 mg/m3 * 1 g/1000 mg * 1 kg/1000 g = 10 kg/hr
HCl flow rate = 10,000 m3/hr * 300 mg/m3 * 1 g/1000 mg * 1 kg/1000 g = 3 kg/hr
HF flow rate = 10,000 m3/hr * 100 mg/m3 * 1 g/1000 mg * 1 kg/1000 g = 1 kg/hr
Next, we calculate the moles of each pollutant using their molecular weights:
Moles of SO2 = 10 kg/hr / 64 kg/kmol = 0.15625 kmol/hr
Moles of HCl = 3 kg/hr / 36.5 kg/kmol = 0.08219 kmol/hr
Moles of HF = 1 kg/hr / 20 kg/kmol = 0.05 kmol/hr
The stoichiometric ratio for CaCO3 is 1.2, which means 1.2 moles of CaCO3 react with 1 mole of each pollutant. Therefore, the total moles of CaCO3 required can be calculated as follows:
Total moles of CaCO3 = 1.2 * (moles of SO2 + moles of HCl + moles of HF)
= 1.2 * (0.15625 + 0.08219 + 0.05) kmol/hr
= 0.375 kmol/hr
Finally, we convert the moles of CaCO3 to kg/day and tons/day:
Total CaCO3 dosage = 0.375 kmol/hr * 100 kg/kmol * 24 hr/day = 900 kg/day
Total CaCO3 dosage in tons/day = 900 kg/day / 1000 kg/ton = 0.9 tons/day
Therefore, the required total limestone (CaCO3) dosage to reduce SO2, HCl, and HF emissions to the specified limits is 1,875 kg/day or 1.875 tons/day.
In this calculation, we determined the limestone dosage required to reduce the emissions of SO2, HCl, and HF in a power plant stack gas to meet regulatory limits. The first step was to convert the uncontrolled emissions from mg/m3 to kg/hr based on the stack gas flowrate.
Then, we calculated the moles of each pollutant using their molecular weights. Considering the stoichiometric ratio between CaCO3 and each pollutant, we determined the total moles of CaCO3 required. Finally, we converted the moles of CaCO3 to kg/day and tons/day to obtain the limestone dosage.
This calculation ensures compliance with the specified emission limits and helps mitigate the environmental impact of the power plant.
Learn more about emissions
brainly.com/question/33156294
#SPJ11
Apply the eigenvalue method to find the general solution of the given system then find the particular solution corresponding to the initial conditions (if the solution is complex, then write real and complex parts). x₁ = 9x₁ + 5x2, x₂ = -6x₁ - 2x₂; x₁ (0)1, x₂ (0) = 0
The eigenvalue method involves finding eigenvalues and eigenvectors of a matrix, using them to construct the general solution, and then obtaining the particular solution by applying initial conditions.
To apply the eigenvalue method, we start by writing the given system of equations in matrix form:
X' = AX,
where X = [x₁, x₂]ᵀ is the column vector of the variables, X' represents the derivative with respect to time, and A is the coefficient matrix:
A = [9 5]
[-6 -2]
Next, we find the eigenvalues and eigenvectors of matrix A. The eigenvalues (λ) satisfy the equation |A - λI| = 0, where I is the identity matrix. Solving this equation, we get:
|9 - λ 5|
|-6 -2 - λ| = 0
Expanding the determinant and solving, we find two eigenvalues:
λ₁ = -1, λ₂ = 10.
To find the eigenvectors corresponding to each eigenvalue, we substitute them back into the equation (A - λI)v = 0, where v is the eigenvector. Solving these equations, we obtain two linearly independent eigenvectors:
v₁ = [1, -2]ᵀ, v₂ = [1, 3]ᵀ.
The general solution of the system is then given by:
X = c₁e^(λ₁t)v₁ + c₂e^(λ₂t)v₂,
where c₁ and c₂ are constants. Substituting the values of the eigenvalues and eigenvectors, we have:
X = c₁e^(-t)[1, -2]ᵀ + c₂e^(10t)[1, 3]ᵀ.
To find the particular solution corresponding to the initial conditions x₁(0) = 1 and x₂(0) = 0, we substitute these values into the general solution and solve for the constants:
[1, 0]ᵀ = c₁[1, -2]ᵀ + c₂[1, 3]ᵀ.
Solving this system of equations, we find c₁ = -1/3 and c₂ = 4/3.
Therefore, the particular solution corresponding to the initial conditions is:
X = -1/3e^(-t)[1, -2]ᵀ + 4/3e^(10t)[1, 3]ᵀ.
Note: The solution is real and does not have complex parts.
To learn more about "matrix" refer here:
https://brainly.com/question/27929071
#SPJ11
With related symmetry operations, show that the point group for cis- and transisomer of 1,2 -difluoroethylene are different.
The point group for the cis- and trans-isomers of 1,2-difluoroethylene are different. This can be demonstrated by examining the symmetry operations present in each isomer and comparing them.
The symmetry operations will determine the point group, which describes the overall symmetry of a molecule.
Symmetry operations are transformations that preserve the overall shape and symmetry of a molecule. These operations include rotation, reflection, inversion, and identity.
By applying these symmetry operations to the molecule, we can determine its point group.
For the cis-isomer of 1,2-difluoroethylene, the molecule has a plane of symmetry perpendicular to the carbon-carbon double bond. This means that if the molecule is divided into two halves along this plane, each half is a mirror image of the other.
Additionally, there is a C2 axis of rotation passing through the carbon-carbon double bond, which results in a 180° rotation that leaves the molecule unchanged. These symmetry operations indicate that the cis-isomer belongs to the point group C2v.
In contrast, the trans-isomer of 1,2-difluoroethylene does not possess a plane of symmetry perpendicular to the carbon-carbon double bond. The molecule lacks any mirror planes or axes of rotation that leave it unchanged. Instead, it possesses a C2 axis of rotation that passes through the carbon-carbon double bond, resulting in a 180° rotation that leaves the molecule unchanged.
Therefore, the trans-isomer belongs to the point group C2h.
By comparing the symmetry operations present in the cis- and trans-isomers of 1,2-difluoroethylene, we can conclude that their point groups are different.
The cis-isomer belongs to the point group C2v, while the trans-isomer belongs to the point group C2h. This difference in symmetry operations accounts for the distinct overall symmetries of these two isomers.
Learn more about isomers from the given link:
https://brainly.com/question/32508297
#SPJ11