Answer:
Ammeter
Explanation:
Instrument for measuring either direct or alternating electric current, in amperes. Ammeters vary in their operating principles and accuracies
Answer:
ammeter is used to measure electric current.
A 10 hp, 60 Hz, 2 pole, 440 volt (line-to-line), three-phase induction motor operates at 3240 rpm at the full load power output of 10 hp. (a) What is the mechanical synchronous speed in rad/sec and in rpm
Answer:
i. 3600 rpm ii. 377 rad/s
Explanation:
(a) What is the mechanical synchronous speed in rad/sec and in rpm
i. The mechanical synchronous speed in rpm
The mechanical synchronous speed in rpm, N = 120f/P where f = frequency = 60 Hz and P = number of poles = 2
So, N = 120f/P = 120 × 60 Hz/2 = 60 × 60 = 3600 rpm
ii. The mechanical synchronous speed in rad/s
We now convert N to rad/s by multiplying by 2π/60
So, the mechanical synchronous speed in rad/s , N' = 3600 rpm × 2π/60 = 60 × 2π = 120π rad/s = 377 rad/s
Student A says that wires on a screw-type terminal connection should be installed as shown in Figure A - 5 . Student 8 says that wire nut connections are a type of soldere connection. Which of the following statements is correct?
Answer:
Student A
Explanation:
There is no reason to solder a wire nut connection because the nut already makes a mechanical connection.
Three district robots are being used today
) Assuming different AM regulations; the receiver is using mixer with subtracting format. The frequency selectivity ratio is approximately 10 and the AM range is from 750 kHz to 2600 kHz. The intermediate frequeney is most nearly:
Answer:
[tex]F=710KHZ[/tex]
Explanation:
From the question we are told that:
Frequency selectivity ratio [tex]R=10[/tex]
AM range 750 kHz to 2600 kHz
Therefore Bandwidth is
[tex]B=2100-680[/tex]
[tex]B=1420KHZ[/tex]
Generally the equation for The intermediate frequency is mathematically given by
Intermediate frequency=\frac{Bandwidth}{2}
[tex]F=\frac{B}{2}[/tex]
[tex]F=\frac{1420}{2}[/tex]
[tex]F=710KHZ[/tex]
Compare and contrast the three USDA quality grades available to consumers and describe how the grades affect labeling.
Answer:
USDA has developed strict measures of quality for products such as grains, rice, corn, and beans. Quality grading is based on the standards developed for each product. Quality grades provide a common language among buyers and sellers, which in turn assures consistent quality for consumers.
Explanation:
in this image if the ground were removed from the neutral wire what would the voltage to ground be?
Answer:
240
Explanation:
Oleg is using a multimeter to test the circuit branch you just installed. After turning off the current to the circuit at the service panel , hell first attach one pole to the ______________ at the end of the run? A) WHITE WIRE B) BOX C) BLACK WIRES) GROUND WIRE
Answer:
Option D, Ground Wire
Explanation:
Oleg is a mustimeter or multi tester or a basic voltage tester which is used to test the ground. The main purpose of the tester is to ensure that the outlet is connected to the ground of the circuit, thereby ensuring its proper functioning.
Hence, option D is correct
A two-position mode controller is used to control the water level in a tank by opening or closing a valve which in the open position allows water at the rate of 0.4 m3 / s to enter the tank. The tank has a cross-sectional area of 12 m2 and water leaves it at the constant rate of 0.2 m3 / s. The valve opens when the water level reaches 4.0 m and closes at 4.4 m. What will be the times taken for (a) the valve opening to closing, (b) the valve closing to opening
Answer:
The right solution is:
(a) 24 sec
(b) 24 sec
Explanation:
The given values are:
Water inlet's flow rate,
= 0.4 m³/s
Water outlet's flow rate,
= 0.2 m³/s
(a)
The volume of water filled will be:
= [tex]Area(height)[/tex]
= [tex]12(4.4-4)[/tex]
= [tex]12\times 0.4[/tex]
= [tex]4.8 \ m^3[/tex]
Opening to closing time taken will be:
= [tex]\frac{4.8}{0.2}[/tex]
= [tex]24 \ sec[/tex]
(b)
Inlet's flow rate,
= 0
Outlet's flow rate will be:
= 0.2 m³/s
Closing to opening time taken will be:
= [tex]\frac{4.8}{0.2}[/tex]
= [tex]24 \ sec[/tex]
a. The time taken for the valve opening to closing is 24 seconds.
b. The time taken for the valve closing to opening is 24 seconds.
Calculation of the time taken:a.
First we need to determine the volume of the water
= Area * height
= 12*(4.4-4)
= 12*0.4
= 4.8
Now the time taken should be
= 4.8/0.2
= 24 seconds.
b. The time taken should be
= 4.8/0.2
= 2.4 seconds
Learn more about time here: https://brainly.com/question/24331923
Polarization: Unpolarized light passes through three ideal polarizing filters. The first filter is oriented with a horizontal transmission axis, the second one has its transmission axis at 30° from the horizontal, and the third filter has a vertical transmission axis. What percent of the light gets through this combination?
Answer:
the percentage of light that gets through this combination is 9.38
Explanation:
Given the data in the question;
Let us represent the incident unpolarized light with [tex]I_0[/tex].
So, the amount of light intensity passing through the first polarizer will be;
[tex]I_1[/tex] = [tex]I_0[/tex] / 2 ------ let this be equation 1
An the amount of light intensity passing through the second polarizer will be;
[tex]I_2[/tex] = [tex]I_1[/tex]cos²θ
given that; the second one has its transmission axis at 30°
so, we substitute;
[tex]I_2[/tex] = [tex]I_1[/tex] × cos²( 30° )
[tex]I_2[/tex] = [tex]I_1[/tex] × 0.75
[tex]I_2[/tex] = 0.75[tex]I_1[/tex]
from equation; [tex]I_1[/tex] = [tex]I_0[/tex] / 2
[tex]I_2[/tex] = 0.75( [tex]I_0[/tex] / 2 )
[tex]I_2[/tex] = 0.375[tex]I_0[/tex] .
Now, the amount of light intensity passing through the third polarizer will be;
[tex]I_3[/tex] = [tex]I_2[/tex]cos² ( 90° - 30° )
[tex]I_3[/tex] = [tex]I_2[/tex] × cos²( 60° )
[tex]I_3[/tex] = [tex]I_2[/tex] × 0.25
we substitute
[tex]I_3[/tex] = 0.375[tex]I_0[/tex] × 0.25
[tex]I_3[/tex] = 0.09375[tex]I_0[/tex]
∴ [tex]I_3[/tex]/[tex]I_0[/tex] × 100 = 0.09375 × 100
⇒ 9.38%
Therefore, the percentage of light that gets through this combination is 9.38
The company PureNSafe is designing a portable, solar-powered disinfection system for Army use only. The system is simply an inlet pipe, a pump, a mixing chamber and an outlet pipe. The water is continuously pumped into the chamber where it is irradiated with UV light before it exits through the the appropriate tube into a collection vessel. The disinfection rate constant rate of disinfection with UV light is 7.80 s.1 and the amount of bacteria has to be reduced by 99.9%. be reduced by 99.9%. Since the Army requires an object that can be carried in a backpack, it requires that the chamber of the apparatus must not hold a capacity greater than 2 L. How much water will the system be able to produce during 10 hours of sunshine?
Solution :
The treatment system will operate as the well mixed chamber.
Disinfection rate constant for the UV light, k is 7.80 /s. Number of bacteria in water need to be reduced by 99.9%
Percent reduction of bacteria should be [tex]$(1-10^{0.99}) \times 100 =89.7\%$[/tex]
Volume of the unit chamber is fixed at 2L
Assume the inlet concentration, [tex]$C_0$[/tex] as 1000
The outlet concentration of bacteria, C should be [tex]$1000-\left(1000 \times \frac{89.7}{100}\right)$[/tex]
= 103
The well mixed chamber will then follow a completely mixed flow reactor model.
Compute the time required :
[tex]$t=\frac{1}{k}\left(\frac{C_0}{C}-1\right)$[/tex]
[tex]$t=\frac{1}{7.8}\left(\frac{1000}{103}-1\right)$[/tex]
= 1.115 s
Flow through the system is [tex]$\frac{2 \ L}{1.115 \ s}$[/tex] = 1.79 L/s
The amount of water treated during the 10 hours of sunlight is 1.79 x 10 x 60 x 60 = 64440 L
The website of a bank that an organization does business with has been reported as untrusted by the organization's web browser. Its security analyst has been assigned to investigate. The analyst discovers the bank recently merged with another local Bank in Combined Names. Additionally, the user's bookmark automatically redirects to the website of the newly-named bank. Which of the following is the most likely cause of this issue?
a) The company's web browser is not up to date
b) The website certificate still has the old bank’s name
c) The website was created to recently to be trusted
d) the website certificate has expired
Answer:
B. The website's certificate still has the old bank's name
Explanation:
MRK ME BRAINLIEST PLZZZZZZZ
Consider a homogeneous, bare, spherical, source-free, critical, uranium-fueled reactor operating at a power Po. Explain how and why the power increases, decreases, or remains unchanged as a result of each of the separate changes to the reactor.
a. The reactor is deformed into the shape of a football (ellipsoid).
b. A person stands next to the core.
c. The temperature of the core is raised.
d. A neutron source is brought close to the core.
e. An energetic electron beam impacts the core.
f. The reactor is run at high power for a long time.
g. The core is launched into outer space.
h. A sheet of cadmium is wrapped around the core.
i. The enrichment of the fuel is increased.
Answer:
a) unchanged
b) unchanged
c) Increase
d) Increase
e) unchanged
f ) Increase
g) unchanged
h) decrease
i) unchanged
Explanation:
Determine how and why the power increases, decreases, or remains unchanged
a) The reactor been deformed will not cause an increase in power i.e. power remains unchanged and this is because power change/generated does not depend on dimension
b) No change will happen to the power ( Unchanged )
c) When the temperature of the core is raised the power increases and this is because of the increase in bombarding of particles causing an increase in charge particle
d) When a neutron source is brought close to the core the power will increase and this is because the presence of more neutron in the core results to an increase in energy released ( more power will be generated )
e) An energetic electron beam impacting the core will not cause an increase in power ( reason been that it is lighter than neutron ) power unchanged
f ) When the reactor is run at a high power there would be an increase in power generated
g) When the core is launched into outer space the power generated remains unchanged
h) when a sheet of Cadmium is wrapped around the core the power generated will be decreased ( reason : Cadmium can absorb neutrons thereby reducing reaction)
i) Increase in the enrichment of the fuel will not cause an increase in the power generated but it will sustain the reaction ( unchanged power )
Argue why electrode therapy is NOT the most effective treatment for brain disorders, and recommend an alternative treatment.
Answer:
Due to risk of damaging of brain.
Explanation:
The electrode therapy is not the most effective treatment for brain disorders because there are various other treatments which can treat the brain disorder without causing damage to the brain. electrode therapy greatly damaged the brain instead of treatment of brain disorder. Medication is the best way to treat brain disorder so that's why electrode therapy is not considered as the most effective treatment for brain disorders, and the doctors recommend an alternative treatment.
List three types of concurrent engineering in manufacturing.
Give three examples of concurrent engineering in manufacturing industries.
Answer:
A famous example of concurrent engineering is the development of the Boeing 777 commercial aircraft. The aircraft was designed and built by geographically distributed companies that worked entirely on a common product database of C A TIA without building physical mock-ups but with digital product definitions.
a poorly tighten terminal is often the cause of a/an ? a) open circuit b) circuit breaker interrupt c)short circuit d) ground fault
Answer: b) circuit breaker interrupt
Explanation:
Wires connect to outlets through terminals and these terminals need to be tight to ensure that electricity flows with the minimum amount of resistance.
If the terminal is poorly tightened, what happens is that resistance will build up as the appliance is being used and this resistance will make the terminal hotter.
The heat will continue to rise until the circuit breaker trips to interrupt the circuit and protect the appliance.
Techm digital definition comprises of
Answer:
Below is the response to the given question:
Explanation:
The relevant services supplied through TechMahindra Digital Services Provider are among the different options given in n inquiry. This is a digital company that has offered its customers an end-to-end solution that digitalizes all the requirements for client operations. It offers digital solutions, services cloud-based, digital marketing strategies, and then all client needs.
You are designing the access control policies for a Web-based retail store. Customers access the store via the Web, browse product information, input their address and payment information, and purchase products. Suppliers can add new products, update product information, and receive orders.The store owner sets the retail prices, makes tailored offers to customers based on their purchasing profiles, and provides marketing services. You have to deal with three actors: StoreAdministrator, Supplier, and Customer. Design an access control policy for all three actors. Customers can be created via the Web, whereas Suppliers are created by the StoreAdministrator.
Answer:
Object-Oriented Software Engineering Using UML, Patterns, and Java, 3e, shows readers how to use both the principles of software engineering and the practices of various object-oriented tools, processes, and products.
5. According to the FMCSRs, you are qualified to operate a CMV if you:
A. are at least 15-years old.
B. have passed an IQ test.
C. have only one current CDL.
D. are currently disqualified from operating a motor vehicle.
Answer:
currently states that a person is qualified to drive a commercial motor vehicle if he/she “can read and speak the English language sufficiently to converse with the general public, to understand highway traffic signs and signals
So I think B
Which of the following can effect LRO?
Answer:
The lunar radiation environment, allowing scientists to determine potential impacts to astronauts and other life. It also will test models on the effects of radiation and measure radiation absorption by a type of plastic that is like human tissue. The results could aid in the development of protective technologies to help keep future lunar crew members safe. CRaTER was built and developed by Boston University and the Massachusetts Institute of Technology in Boston.
Leticia radio is getting interference whenever she uses it in her dining room. What's the most likely reason/s.
Answer: D. There is a dimmer switch
Explanation:
Dimmer switches have been known to cause radio interference especially the solid state ones. To counter this, dimmer switches usually come with a component to suppress radio interference, this doesn't work for all dimmers and the cheaper dimmers are usually more prone to this problem.
If Leticia's dining room makes use of a dimmer switch, it is the most probable reason for radio interference.
please solve part two
Answer:
Wat part 2
Explanation:
Engineers study the properties of fluids, including viscosity and compressibility, to test the efficiency of systems under given conditions. True or False?
Answer:
True.
Explanation:
The compressibility of a fluid can be defined as a measure of the change in volume (density) with respect to the amount of pressure applied to the fluid. Thus, as the pressure of a compressible fluid increases, both its viscosity and density increases.
Some examples of compressible fluids are vapors, gases, air etc.
Additionally, the compressibility of fluids plays a significant role in the field of science such as in aerodynamics, fluid mechanics, thermodynamics etc.
Viscosity can be defined as a quantity expressing the magnitude of internal friction that restricts the ease of flow between parallel layers at some distance apart having unit speed relative to each other.
These properties of fluids, including viscosity and compressibility are usually being studied by engineers such as civil engineers, in order to test the efficiency of systems under given conditions.
Answer:
true
Explanation:
edge
On a TXV system, the temperature sensing bulb is located at the
A condenser outlet
B evaporator outlet
C condenser inlet
D evaporator inlet
Answer:
Explanation:
B evaporator outlet: on the suction line between the evaporator and the compressor
Need help hurry 20 Briefly describe an idea for a new product, while thinking mainly about its cost analysis. Depict what kinds of direct and indirect costs will be involved in its creation.
Answer: Contaminants can cause tremendous harm to a population; not only humans but entire local animal species can be devastated by poisonous drinking water. Crops and livestock can also be affected. Citizens can make prudent choices regarding natural resources and energy use. Scientists can research and create products that can reduce or eliminate unnecessary waste and pollution.
Explanation:
A process fluid having a specific heat of 3500 J/kg-K and flowing at 2 kg/s is to be cooled from 80 C to 50 C with chilled water, which is supplied at a temperature of 15 C and a flow rate of 2.5 kg/s. Assuming an overall heat transfer coefficient of 2000 W/m2-K, calculate the required heat transfer areas for the following exchanger configurations: (a) parallel flow (15 pts), and (b) counterflow (15 pts).
Answer:
to claim your answer $2 Approach www.gotit-pro.com
Explanation:
A cell has an interesed resistance of 0.02 and an e.m.f mind of 2.0 V
Calculate its terminal p.d if it delivers 5A
Answer:
Answer:
(a) The terminal voltage of the cell is 1.9 V.
(b) The terminal voltage of the cell is 1.0 V.
Explanation:
If wrong sorry but if right please give brainliest
A flow of 2.6 MGD leaves a primary clarifier with a BOD of 131 mg/L. Determine the aeration period (hydraulic detention time) of an activated sludge tank that has a BOD loading of 35 lbsper 1000 ft3per day. Determine the sludge age of the facility given the following data: VSS concentration is 2100 mg/L, and the mass rate of wasted sludge is equal to 44 percent of the BOD loading.
Answer:
8.5 days
Explanation:
Given data :
Flow ( Q ) = 2.6 MGD = 11819.834 m^3/day
BOD = 131 mg/L
BOD loading rate = 35 Ibs/1000 ft^3 per day = 0.5606 kg/m^3/day
Calculate the sludge age of the facility
Given the BOD applied to the aeration tank = 11819.834 m^3/day * 131mg/l
= 1548.398 kg/day
first calculate the volume of the aeration tank
V = BOD applied / BOD loading rate
V = 1548.398 / 0.5606 = 2762.03 m^3
Hydraulic Detention time = V / Q
= 2762.03 / 11819.834 = 0.2336 day = 5.6 hour
next : determine the mass rate of the waste
= 44% * 0.5606 kg/m^3/day
= 0.2466 kg/m^2/day
finally determine the sludge age
= V * Xt / ∅w * R
= ( 2762.03 m^3 * 2100 * 10^-3 ) / ( 0.2466 * 2762.03 kg/day )
= 8.5 days
what does kichfoff's currebt law
Answer:
Kirchhoff's current law (1st Law) states that the current flowing into a node (or a junction) must be equal to the current flowing out of it
Explanation:
Air entrainment is used in concrete to: __________.
1. Strengthen the concrete
2. Increase the resistance of the concrete to freeze thaw damage
3. Create a better surface appearance
4. Make the concrete easier to handle during placement
5. Help evaporate excess water from the curing concrete
The answer is number 2) Increase the resistance of the concrete to freeze-thaw damage.
Air entrainment is used in concrete to Increase the resistance of the concrete to freeze thaw damage.
What is air entrainment?Microscopic air bubbles embedded in the concrete's surface reduce internal pressure by creating little spaces for water to expand into during freeze-thaw cycles.
Without these pockets, water has nowhere to escape, which causes concrete to crack and/or scale, severely reducing the lifespan of a structure. An air entraining additive, or AEA, is used to add air to the concrete mix.
To fit the requirements of the task at hand, a mix's air content can be changed. When pouring concrete in locations that experience freeze-thaw conditions, using air-entrained concrete is advantageous.
Therefore, Air entrainment is used in concrete to Increase the resistance of the concrete to freeze thaw damage.
To learn more about entrainment, refer to the link:
https://brainly.com/question/15180040
#SPJ2
ogla has mistakenly created a connection between the black and white wire. What has she created? A) open circuit B) SHORT CIRCUIT C) GROUND CIRCUIT D) AC
Answer:
B) SHORT CIRCUIT
Explanation: