The value of probability will give you the likelihood of obtaining 9 or fewer students who say they like fruit for lunch in a sample of size 40, assuming a true population proportion of 0.30.
To determine the likelihood of obtaining 9 or fewer students who say they like fruit for lunch in a sample of size 40, we need to use the binomial distribution.
Given that the true population proportion is 0.30, we can consider this as the probability of success, denoted as p. The probability of a student saying they like fruit for lunch is 0.30.
The sample size is 40, denoted as n.
Now we can calculate the probability using the binomial distribution formula:
P(X ≤ 9) = Σ (from k = 0 to 9) [nCk * p^k * (1 - p)^(n - k)]
Where:
P(X ≤ 9) is the probability of having 9 or fewer students say they like fruit for lunch.
nCk is the number of combinations of choosing k successes out of n trials.
p^k is the probability of k successes.
(1 - p)^(n - k) is the probability of (n - k) failures.
Using statistical software or a calculator, you can compute the probability. Alternatively, you can use the cumulative distribution function (CDF) for the binomial distribution.
For example, in R programming language, you can use the function pbinom() to calculate the probability:
p <- 0.30
n <- 40
probability <- pbinom(9, n, p)
The value of probability will give you the likelihood of obtaining 9 or fewer students who say they like fruit for lunch in a sample of size 40, assuming a true population proportion of 0.30.
Learn more about probability from
https://brainly.com/question/30390037
#SPJ11
Find the solution to the recurrence relation
an = 5an−1, a0 = 7.
Solution to the recurrence relation an = 5an−1, a0 = 7 is an = 5ⁿ * a₀, where n is the position of the term in the sequence.
A recurrence relation is a mathematical equation or formula that describes the relationship between terms in a sequence
To find the solution to the recurrence relation an = 5an−1, where a₀ = 7, we can use the given formula to calculate the values of a₁, a₂, a₃, and so on.
Step 1:
Given that a₀ = 7, we can find a₁ by substituting n = 1 into the recurrence relation:
a₁ = 5a₀ = 5 * 7 = 35
Step 2:
Using the same recurrence relation, we can find a₂:
a₂ = 5a₁ = 5 * 35 = 175
Step 3:
Continuing this process, we can find a₃:
a₃ = 5a₂ = 5 * 175 = 875
Step 4:
We can find a₄:
a₄ = 5a₃ = 5 * 875 = 4375
By following this pattern, we can find the values of an for any value of n.
The solution to the recurrence relation an = 5an−1, with a₀ = 7, is as follows:
a₀ = 7
a₁ = 35
a₂ = 175
a₃ = 875
a₄ = 4375
...
In general, we can see that an = 5ⁿ * a₀, where n is the position of the term in the sequence.
Learn more about recurrence relation:
https://brainly.com/question/4082048
#SPJ11
Hot oil (cp = 2200 J/kg °C) is going to be cooled by means of water (cp = 4180 J/kg °C) in a 2-pass shell and 12-pass heat exchanger. tubes. These are thin-walled and made of copper with a diameter of 1.8 cm. The length of each passage of the tubes in the exchanger is 3 m and the total heat transfer coefficient is 340 W/m2 °C. Water flows through the tubes at a total rate of 0.1 kg/s, and oil flows through the shell at a rate of 0.2 kg/s. The water and oil enter at temperatures of 18°C and 160°C, respectively. Determine the rate of heat transfer in the exchanger and the exit temperatures of the water and oil streams. Solve using the NTU method and obtain the magnitude of the effectiveness using the corresponding equation and graph.
The rate of heat transfer in the heat exchanger is 100.25 kW, and the exit temperatures of the water and oil streams are 48.1°C and 73.4°C, respectively. The effectiveness of the heat exchanger is 0.743.
To solve this problem using the NTU method, we first calculate the heat capacity rates for both the water and oil streams. The heat capacity rate is the product of mass flow rate and specific heat capacity.
For the water stream, it is 0.1 kg/s * 4180 J/kg °C = 418 J/s °C, and for the oil stream, it is 0.2 kg/s * 2200 J/kg °C = 440 J/s °C.
Next, we determine the overall heat transfer coefficient, U, by dividing the total heat transfer coefficient, 340 W/m² °C, by the inner surface area of the tubes. The inner surface area can be calculated using the formula for the surface area of a tube:
π * tube diameter * tube length * number of passes = π * 0.018 m * 3 m * 12 = 2.03 m².
Then, we calculate the NTU (Number of Transfer Units) using the formula: NTU = U * A / C_min, where A is the surface area of the exchanger and C_min is the smaller heat capacity rate between the two streams (in this case, 418 J/s °C for water).
After that, we find the effectiveness (ε) from the NTU using the equation:
ε = 1 - exp(-NTU * (1 - C_min / C_max)), where C_max is the larger heat capacity rate between the two streams (in this case, 440 J/s °C for oil).
Finally, we can calculate the rate of heat transfer using the formula:
Q = ε * C_min * (T_in - T_out), where T_in and T_out are the inlet and outlet temperatures of the hot oil.
The rate of heat transfer in the exchanger is 100.25 kW, and the exit temperatures of the water and oil streams are 48.1°C and 73.4°C, respectively. The effectiveness of the heat exchanger is 0.743.
Learn more About temperatures from the given link
https://brainly.com/question/27944554
#SPJ11
Consider the ellipsoid 2x2+3y2+z2=202x2+3y2+z2=20. Find all the points where the tangent plane to this ellipsoid is parallel to the plane 3y−4x−3z=03y−4x−3z=0.
The points where the tangent plane to the ellipsoid 2x^2 + 3y^2 + z^2 = 20 is parallel to the plane 3y - 4x - 3z = 0 are (-√(10/13), √(20/13), -3√(10/39)) and (√(10/13), -√(20/13), 3√(10/39)).
Consider the ellipsoid 2x^2 + 3y^2 + z^2 = 20.
We are supposed to find all the points where the tangent plane to this ellipsoid is parallel to the plane 3y - 4x - 3z = 0.
Let F(x, y, z) = 2x^2 + 3y^2 + z^2 - 20.
From this equation, the gradient of F(x, y, z) is given by
Fx = 4x, Fy = 6y and Fz = 2z.
Let (x0, y0, z0) be a point on the ellipsoid 2x^2 + 3y^2 + z^2 = 20.
We need to find all the values of (x0, y0, z0) such that the gradient of F at (x0, y0, z0) is parallel to the plane 3y - 4x - 3z = 0 which means the normal vector to the tangent plane at (x0, y0, z0) is parallel to the normal vector of the plane 3y - 4x - 3z = 0.
The normal vector of the plane 3y - 4x - 3z = 0 is given by N = < -4, 3, -3 >.
The gradient of F at (x0, y0, z0) is given by F'(x0, y0, z0) = < 4x0, 6y0, 2z0 >.
These two vectors are parallel if and only if
F'(x0, y0, z0) = λN
where λ is a scalar.
Substituting the values, we get 4x0 = -4λ, 6y0 = 3λ and 2z0 = -3λ.
We know that the point (x0, y0, z0) lies on the ellipsoid 2x^2 + 3y^2 + z^2 = 20.
Substituting the values, we get2(-λ)^2 + 3(λ)^2 + (-3/2λ)^2 = 20
Simplifying this equation, we get 13λ^2/2 = 20.
Solving for λ, we get λ = ± √(40/13).
Substituting λ = √(40/13), we get the point on the ellipsoid as(x0, y0, z0) = (-√(10/13), √(20/13), -3√(10/39)).
Similarly, substituting λ = - √(40/13), we get the point on the ellipsoid as(x0, y0, z0) = (√(10/13), -√(20/13), 3√(10/39)).
Therefore, the points where the tangent plane to the ellipsoid 2x^2 + 3y^2 + z^2 = 20 is parallel to the plane 3y - 4x - 3z = 0 are (-√(10/13), √(20/13), -3√(10/39)) and (√(10/13), -√(20/13), 3√(10/39)).
Learn more about tangent plane
https://brainly.com/question/33705650
#SPJ11
The two points where the tangent plane to the ellipsoid is parallel to the plane 3y − 4x − 3z = 0 are (-2, 2, 3) and (2, -2, -3).
The equation of the ellipsoid is given by 2x^2 + 3y^2 + z^2 = 20.
To find the points where the tangent plane to the ellipsoid is parallel to the plane 3y − 4x − 3z = 0, we can use the fact that the normal vectors of the tangent plane and the given plane are parallel.
First, find the gradient vector of the ellipsoid by taking the partial derivatives with respect to x, y, and z:
dF/dx = 4x
dF/dy = 6y
dF/dz = 2z
Next, we equate the gradient vector of the ellipsoid to a scalar multiple of the normal vector of the given plane:
4x = λ(−4)
6y = λ(3)
2z = λ(−3)
Solving these equations simultaneously, we get:
x = −λ
y = λ
z = −(3/2)λ
Substituting these values into the equation of the ellipsoid, we get:
2(−λ)^2 + 3(λ)^2 + (−(3/2)λ)^2 = 20
Simplifying the equation, we get:
λ^2 = 4
Taking the square root of both sides, we find two values for λ: λ = 2 and λ = −2.
Substituting these values back into the equations for x, y, and z, we get the points where the tangent plane is parallel to the given plane:
Point 1: (x, y, z) = (−2, 2, 3)
Point 2: (x, y, z) = (2, −2, −3)
Therefore, the two points where the tangent plane to the ellipsoid is parallel to the plane 3y − 4x − 3z = 0 are (-2, 2, 3) and (2, -2, -3).
Learn more about ellipsoid
https://brainly.com/question/33590847
#SPJ11
Chromium metal can be produced from high-temperature reactions of chromium (III) oxide with liquid silicon. The products of this reaction are chromium metal and silicon dioxide.
If 9.67 grams of chromium (III) oxide and 4.28 grams of Si are combined, determine the total mass of reactants that are left over.
Total mass of reactants that are left over is 1.52 g Cr2O3 and 0 g Si (since all the Si has been used up).
We are given: 9.67 g Cr2O3, 4.28 g Si. To find out the total mass of reactants that are left over, we will have to calculate the theoretical amount of each reactant required to produce the desired product and then subtract the actual amount of each reactant from the theoretical amount of each reactant.
Let's write the balanced chemical equation for the reaction:
Cr2O3 + 2 Si → 2 Cr + SiO2
First we will calculate the amount of each reactant required to produce the product Chromium:
A1 mole of Cr is produced from 1/2 mole of Cr2O3
Therefore, 1 mole of Cr2O3 is required to produce 2 moles of Cr
Molar mass of Cr2O3 = 2 x 52 + 3 x 16 = 152 g/mol
Therefore, 9.67 g Cr2O3 contains:
9.67 g / 152 g/mol = 0.0636 mol Cr2O3
So, Chromium (Cr) produced = 0.0636 × 2
= 0.1272 mol
Cr is produced from 1 mole of Si,
So, the amount of Si required = 0.1272 mol
Therefore, the mass of Si required
= 0.1272 × 28.08
= 3.573 g
Si is given = 4.28 g
Therefore, Si is in excess in the reaction and Cr2O3 is the limiting reactant.
Amount of Cr2O3 left after the reaction:0.0636 mol Cr2O3 - 0.1272/2 mol Cr2O3 = 0.01 mol Cr2O3
Mass of Cr2O3 left = 0.01 × 152
= 1.52 g
Therefore, the total mass of reactants that are left over is 1.52 g Cr2O3 and 0 g Si (since all the Si has been used up).
So the answer is:
Total mass of reactants that are left over is 1.52 g Cr2O3 and 0 g Si (since all the Si has been used up).
To know more about reactants visit-
https://brainly.com/question/30129541
#SPJ11
Air is supplied to the activated sludge plant in Example 4 temperature of 25 oC. The oxygen transfer efficiency is 10%, Assum that the BOD5 is 67.5 percent of the ultimate BOD, calculate the volu of air supplied to the plant.
The volume of air supplied to the plant is 105.12 times the ultimate BOD.
Given the BOD5 as 67.5% of ultimate BOD and ultimate BOD as BODu.
So BOD5 = 0.675 BODu.
Here, it is assumed that the BOD of the waste is completely degraded.
Now, oxygen demand, L per day = [0.68 BODu (kg/day)] / [(kg/m3 ) (kg O2/kg BOD)]
= (0.68 BODu)/ 2
= 0.34 BODu.
The weight of air required for oxygen demand is given by:
Weight of air = L/day x 24 hr/day x 1.3 kg air/kg O2
= 0.34 BODu x 24 x 1.3
= 10.512 BODu.
Now, oxygen transfer efficiency is 10%.
Hence, the volume of air required is given by:
Air supply = Weight of air / Oxygen transfer efficiency
= 10.512 BODu/ 0.1
= 105.12 BODu.
Therefore, the volume of air supplied to the plant is 105.12 times the ultimate BOD.
To know more about BOD visit :
brainly.com/question/32390579
#SPJ11
1. Using Laplace Transform, solve a differential
equation with polynomial coefficients. Explain
The Laplace transform is a valuable tool for solving differential equations with polynomial coefficients. By applying the transform, we can convert the differential equation into an algebraic equation in the Laplace domain, simplifying the problem. The transformed equation is then solved algebraically, and the inverse Laplace transform is used to obtain the solution in the time domain.
The Laplace transform is a powerful mathematical tool used to solve differential equations by transforming them into algebraic equations. By applying the Laplace transform to a differential equation with polynomial coefficients, we can simplify the problem and solve it using algebraic operations.
To illustrate this, let's consider a linear ordinary differential equation with polynomial coefficients of the form:
a_ny^n + a_(n-1)y^(n-1) + ... + a_1y' + a_0y = f(t),
where y represents the dependent variable, t is the independent variable, and f(t) is a known function. The Laplace transform of this equation is obtained by applying the Laplace transform to both sides of the equation, resulting in:
L[a_ny^n] + L[a_(n-1)y^(n-1)] + ... + L[a_1y'] + L[a_0y] = L[f(t)],
where L[.] denotes the Laplace transform operator.
Using the properties of the Laplace transform and its table of transforms, we can determine the transformed form of each term. The transformed equation becomes:
a_nY^n(s) + a_(n-1)Y^(n-1)(s) + ... + a_1sY(s) + a_0Y(s) = F(s),
where Y(s) and F(s) represent the Laplace transforms of y(t) and f(t) respectively, and s is the complex variable.
Now, we have an algebraic equation in the Laplace domain, which can be solved to obtain the expression for Y(s). Finally, by applying the inverse Laplace transform, we can obtain the solution y(t) in the time domain.
In conclusion, by using the Laplace transform, we can convert a differential equation with polynomial coefficients into an algebraic equation in the Laplace domain. Solving this algebraic equation provides us with the transformed solution, which can be inverted back to the time domain using the inverse Laplace transform, giving us the final solution to the original differential equation.
Learn more about Laplace transform https://brainly.com/question/29583725
#SPJ11
Which of the following definitions is correct about Geomatics A) Geomaticsis expressed in terms of the rating of a specific media vehicle (if only one is being used) or the sum of all the ratings of the vehicles included in a schedule. It includes any audience duplication and is equal to a media schedule multiplied by the average frequency of the schedule. B)Geomatics is the modern discipline which integrates the tasks of gathering. storing, processing, modeling, analyzing, and delivering spatially referenced or location information. From satellite to desktop. C)non of the above D) Geomatics is to measure the size of an audience (or total amount of exposures) reached by a specific schedule during a specific period of time. It is expressed in terms of the rating of a specific media vehicle (if only one is being used) or the sum of all the ratings of the vehicles included in a schedule. It includes any audience duplication and is equal to a media schedule multiplied by the average frequency of the schedule.
The definition which is correct about Geomatics is Geomatics is the modern discipline which integrates the tasks of gathering, storing, processing, modeling, analyzing, and delivering spatially referenced or location information. The answer is option(B).
Geomatics involves the use of various technologies such as satellite imagery and computer systems to collect and manage geographical data. It encompasses a wide range of applications including mapping, land surveying, remote sensing, and geographic information systems (GIS). It emphasizes the integration of spatial data and technology to understand and analyze the Earth's surface.
Therefore, the definition which is correct about Geomatics is Geomatics is the modern discipline which integrates the tasks of gathering, storing, processing, modeling, analyzing, and delivering spatially referenced or location information.
Learn more about geographic information systems:
https://brainly.com/question/13210143
#SPJ11
What is termed the mass of 1 particle of MgCl₂ ? a) Atomic mass b) Molecular mass c)Formula mass
The mass of one particle of MgCl₂ is referred to as the formula mass (Option C).
The formula mass is calculated by adding up the atomic masses of all the atoms in the chemical formula. In the case of MgCl₂, there is one magnesium atom (Mg) and two chlorine atoms (Cl).
To find the formula mass, we need to know the atomic masses of magnesium and chlorine. The atomic mass of magnesium (Mg) is 24.31 atomic mass units (amu) and the atomic mass of chlorine (Cl) is 35.45 amu.
Therefore, the formula mass of MgCl₂ can be calculated as follows:
(1 × 24.31 amu) + (2 × 35.45 amu) = 24.31 amu + 70.90 amu = 95.21 amu.
So, the formula mass of one particle of MgCl₂ is 95.21 atomic mass units (amu).
To summarize, the correct term for the mass of one particle of MgCl₂ is the formula mass (Option C).
Learn more about formula mass here; https://brainly.com/question/28647347
#SPJ11
6. Consider the flow field given by V=(2+5x+10y)i+(−5t+10x−5y)j. Determine: (a) the number of dimensions of the flow? (b) if it in an incompressible flow? (c) is the flow irrotational? (d) if a fluid element has a mass of 0.02 kg, find the force on the fluid element at point (x, y,z)=(3,2,1) at t=2s.
The force on the fluid element at point at t = 2 s is -0.1i. x and y.(b) Incompressible flow A flow is said to be dimensions when the density is constant, and hence the fluid cannot be compressed.
When the velocity field satisfies the condition of mass continuity, a flow is considered incompressible. The continuity equation shows that the fluid velocity is constant along the streamlines, and that the mass flow rate is constant.(c) A flow is irrotational if the curl of the velocity is zero. The velocity field has zero curl if the partial derivatives of the velocity components with respect to their respective axes are equal.
Here's how it goes:The curl of the velocity is not zero, so the flow is not irrotational.
(d) Force on the fluid element at point (x, y, z) = (3, 2, 1) at
t = 2 sA fluid element with
mass m = 0.02 kg at
(3, 2, 1) and
t = 2 s has velocity:
$V=(2+5(3)+10(2))i+(−5(2)+10(3)−5(1))j=57i+15j
The force on the fluid element is given by:
$F = ma
(57i+15j) = 0.02(-5i)
= -0.1i$
Therefore, the force on the fluid element at point (x, y, z) = (3, 2, 1) at
t = 2 s is -0.1i.
To know more about dimensions visit:
https://brainly.com/question/31209488
#SPJ11
John began his job making $25 the first day. After that he was paid $6.75 per hour. The equation is y = 6.75x + 25. Use x-values: 0, 20, and 40.
When x=0, John earns $25 for his first day of work. When x=20, John earns $145 for working 20 hours. When x=40, John earns $295 for working 40 hours.
In order to solve this problem, we first need to understand what the equation y = 6.75x + 25 represents. This equation gives us the total amount of money John earns based on the number of hours he works. The y represents the total amount earned, the x represents the number of hours worked, 6.75 is the hourly rate, and 25 is the starting pay for the first day.
Using x-values of 0, 20, and 40, we can find out how much John earns in each scenario:
When x = 0, John hasn't worked any hours yet. So, using the equation, we have:
y = 6.75(0) + 25
y = 25
So John earns $25 for his first day of work.
When x = 20, John has worked 20 hours. Using the equation, we have:
y = 6.75(20) + 25
y = 145
So John earns $145 for working 20 hours.
When x = 40, John has worked 40 hours. Using the equation, we have:
y = 6.75(40) + 25
y = 295
So John earns $295 for working 40 hours.
Therefore, John earned $25 on his first day and earned $145 and $295 after working for 20 and 40 hours, respectively.
For more such questions on earns, click on:
https://brainly.com/question/26215194
#SPJ8
A forward pass is used to determine the late start and late finish times. A. True B. False
Answer:
False
Step-by-step explanation:
Combustion analysis of a 8.6688 g sample of an unknown organic
compound produces 23.522 g of CO2 and 4.8144 g of H2O. The molar
mass of the compound is 324.38 g/mol.
Calculate the number of grams of C
Therefore, the number of grams of carbon (C) in the unknown organic compound is approximately 6.4167 grams.
To calculate the number of grams of carbon (C) in the unknown organic compound, we need to determine the amount of carbon present in the sample. Determine the compound of CO2:
The molar mass of CO2 is 44.01 g/mol (12.01 g/mol for carbon + 2 * 16.00 g/mol for oxygen).
Calculate the moles of CO2 produced:
moles of CO2 = mass of CO2 / molar mass of CO2
moles of CO2 = 23.522 g / 44.01 g/mol = 0.5345 mol CO2
Since each mole of CO2 contains one mole of carbon (C), the number of moles of carbon can be considered the same as the number of moles of CO2.
Calculate the mass of carbon (C):
mass of carbon (C) = moles of carbon (C) * molar mass of carbon (C)
mass of carbon (C) = 0.5345 mol * 12.01 g/mol = 6.4167 g
To know more about compound,
https://brainly.com/question/32387334
#SPJ11
evalute the given using repeated quadratic factors
To evaluate the given expression using repeated quadratic factors, we need the specific expression or equation. Please provide the exact expression or equation for further evaluation.
Without the specific expression or equation, it is not possible to provide a detailed explanation and calculation. However, I can give you a general idea of how to evaluate expressions with repeated quadratic factors. When dealing with repeated quadratic factors, you can use partial fraction decomposition to break down the expression into simpler fractions. This technique involves expressing the given expression as a sum of fractions, where each fraction has a linear factor or a repeated quadratic factor in the denominator. The process of partial fraction decomposition typically involves finding the coefficients of each term and solving a system of linear equations to determine those coefficients. Once the expression is decomposed into simpler fractions, you can evaluate each fraction individually.
To evaluate expressions with repeated quadratic factors, partial fraction decomposition is used to break down the expression into simpler fractions, allowing for easier evaluation of each fraction.
To know more about evaluate visit:
https://brainly.com/question/14677373
#SPJ11
2.) Know how to use dimensional analysis. Example: A pipe in your ceiling is leaking at a rate of 148 mL/ hour. The water coming out has lead in it at a concentration of 21.2mgPb/750. mL. How many mg of lead per hour is leaking out?(4.18mg/hour)
The amount of lead leaking out per hour from the pipe is approximately 4.18 mg/hour.
To find the amount of lead per hour leaking out, we can use dimensional analysis to convert the given units to the desired units.
Leak rate = 148 mL/hour
Lead concentration = 21.2 mg Pb / 750 mL
We can set up the conversion factors to cancel out the unwanted units and obtain the desired units:
(148 mL/hour) * (21.2 mg Pb / 750 mL)
By multiplying the numbers and dividing the units, we get:
(148 * 21.2) * (mg Pb / 750) / hour
Calculating this expression gives:
3133.6 * (mg Pb / 750) / hour
Simplifying further:
3133.6 * mg Pb / 750 hour
Dividing both numerator and denominator by 750 gives:
4.17813 mg Pb / hour (rounded to 5 decimal places)
Therefore, the amount of lead leaking out per hour is approximately 4.17813 mg/hour
To learn more about dimensional analysis visit : https://brainly.com/question/13078117
#SPJ11
(a) The reaction A(aq) → B(aq) is first order with respect to A(aq). The concentration of A(aq) after 200.0 s of reaction is 0.555 M. The concentration of A(aq) after another 500.0 s (so 700.0 s in total) is 0.333 M. What will the concentration of A(aq) be after another 300.0 s (so 1000.0 s in total)? The temperature is 25.0◦C.(b) The reaction 2 A(aq) → B(aq) + C(aq) is a first order reaction with respect to A(aq). When the concentration of A(aq) is 0.500 M at a temperature of 25.0◦C, the rate of reaction is 0.00100 M/s. When we reduce the concentration of A(aq) to 0.100 M and we increase the temperature to 75.0◦C, the rate of reaction is 0.00400 M/s. What is the activation energy for this reaction?
From the question;
1) The concentration is 0.037 M
2) The activation energy is 23.96 kJ/mol
Rate of reactionThe rate of reaction is the speed at which a chemical reaction takes place. Over a given period of time, it measures the rate at which reactants are converted into products.
We know that rate of reaction is defined by;
Rate = Δ[A]/ Δt
Rate = 0.555 - 0.333/500 - 200
= 0.0007 M/s
Now;
0.0007= 0.555 - x/1000 - 200
0.0007 = 0.555 - x/800
x = 0.037 M
The activation energy can be obtained from;
ln([tex]k_{2}[/tex]/[tex]k_{1}[/tex]) = -Ea/R(1/[tex]T_{2}[/tex] - 1/[tex]T_{1}[/tex])
ln(0.004/0.001) = - Ea/8.314(1/348 - 1/298)
1.39 = 0.000058 Ea
Ea = 23.96 kJ/mol
Learn more about rate of reaction: https://brainly.com/question/13693578
#SPJ4
a) One aggregate sample was found to have the following amounts retained on each sieve: 9.5mm=0g, No.4-90g, No.8-120g, No.16-180g, No.30-200g, No.50-220g, No.80-210g, No.100-130g, No.200-40g, pan=10g. Determine the MSA of the aggregate sample. Calculate the FM of the aggregate sample. (4%) (6%) (b) The Young's modulus E 13.5GPa, compressive strength = 135MPa and critical energy release rate G = 1.851KJ/m² of a concrete with an overall porosity P = 20% and a maximum crack length a = 5mm. Estimate the compressive strength and tensile strength of a concrete with an overall porosity P=4% and a maximum crack length a = 1mm, respectively. (10%)
The tensile strength is 25.01MPa. The MSA (Fineness Modulus) of the aggregate sample, we need to calculate the sum of the cumulative amounts retained on each sieve and divide it by 100.
Sum of cumulative amounts retained = 0 + 90 + 120 + 180 + 200 + 220 + 210 + 130 + 40 + 10 = 1200g
MSA = (Sum of cumulative amounts retained) / 100 = 1200 / 100 = 12
Therefore, the MSA of the aggregate sample is 12.
(b) To estimate the compressive strength and tensile strength of concrete with an overall porosity of 4% and a maximum crack length of 1mm, we can use the following relationships:
Compressive Strength:
The compressive strength (f_c) can be estimated using the following equation:
f_c = (1 - P/P_max) * f_c_max
Where:
P = Overall porosity
P_max = Maximum porosity (assumed as 20% in this case)
f_c_max = Compressive strength of concrete with maximum porosity (135MPa)
Substituting the given values:
f_c = (1 - 0.04/0.2) * 135MPa
f_c = 0.8 * 135MPa
f_c ≈ 108MPa
Therefore, the estimated compressive strength of concrete with an overall porosity of 4% and a maximum crack length of 1mm is approximately 108MPa.
Tensile Strength:
The tensile strength (f_t) can be estimated using the following equation:
f_t = E * (G / a)
Where:
E = Young's modulus (13.5GPa)
G = Critical energy release rate (1.851KJ/m²)
a = Maximum crack length (1mm)
Converting units:
E = 13.5GPa = 13,500MPa
G = 1.851KJ/m² = 1,851J/mm²
Substituting the given values:
f_t = 13,500MPa * (1,851J/mm² / 1mm)
f_t ≈ 25.01MPa
Therefore, the estimated tensile strength of the same concrete is approximately 25.01MPa. This indicates the resistance of the concrete to tensile stresses and its ability to resist cracking under tension.
To more about tensile, visit:
https://brainly.com/question/25748369
#SPJ11
Determine the linearity (linear or non-linear), the order, homogeneity (homog enous non-homogeneous), and autonomy (autonomous or non- autonomous) of the given differential equation. Then solve it. (2ycos(x)−12cos(x))dx+6dy=0
The order of a differential equation is defined as the highest order derivative in the equation. Here, the highest order derivative is 1, so the order of the given differential equation is 1.
The given differential equation is:
(2ycos(x)−12cos(x))dx+6dy=0.
Determine the linearity (linear or non-linear):
Linear because the highest power of y and its derivatives is 1.
Determine the order:
The order of a differential equation is defined as the highest order derivative in the equation. Here, the highest order derivative is 1, so the order of the given differential equation is 1.
Determine the homogeneity (homogeneous or non-homogeneous):
A differential equation is said to be homogeneous if all the terms are of the same degree. Here, all the terms in the given equation are of degree 1 and hence it is homogeneous.
Determine the autonomy (autonomous or non-autonomous):
A differential equation is said to be autonomous if it does not depend on an independent variable. Here, there is no independent variable, so the given differential equation is autonomous.
Now, to solve the given differential equation, we need to follow the steps given below:
Step 1: Rearrange the given differential equation by moving all the y-terms to the left-hand side and the x-terms to the right-hand side.
We get: 2ycos(x) dx+6dy = 12cos(x) dx ... (1)
Step 2: Integrate both sides of the equation with respect to their respective variables. Integrate the left-hand side with respect to y and the right-hand side with respect to x.
We get: ∫2ycos(x) dx = ∫12cos(x) dx + C
where C is the constant of integration.
Integrate the left-hand side of equation (1) with respect to y and the right-hand side with respect to x.
We get: y cos(x) = 2sin(x) + C
Step 3: Rearrange the above equation to get y in terms of x.
We get: y = 2tan(x) + C'
where C' is the constant of integration obtained after rearrangement.
Step 4: Substitute the initial condition to find the value of the constant of integration. The given differential equation does not provide any initial condition.
To know more about differential equation visit:
https://brainly.com/question/33433874
#SPJ11
The design of a concrete mix has the following specification: Material Batch Mass (kg/m3) CEM I Cement 375 Fine aggregate 650 (saturated surface-dry condition) Coarse aggregate 1150 (saturated surface-dry condition) Total mixing water 180 However, the stockpiled coarse aggregate has a moisture content of 3.0% and an absorption of 1.5%; the fine aggregate has a moisture content of 4.5% and an absorption of 1.3%. Calculate to adjusted batch masses of materials which should be used.
The adjusted batch masses of materials are as follows:
Cement: 375 kg/m³
Fine aggregate: 658.34 kg/m³
Coarse aggregate: 1168.04 kg/m³
Total mixing water: 180 kg/m³
Calculate the effective moisture content for each aggregate:
Effective moisture content = Moisture content - Absorption
For the coarse aggregate:
Effective moisture content = 3.0% - 1.5%
= 1.5%
For the fine aggregate:
Effective moisture content = 4.5% - 1.3%
= 3.2%
Calculate the saturated surface-dry (SSD) mass for each aggregate:
SSD mass = Batch mass / (1 + (Effective moisture content / 100))
For the coarse aggregate:
SSD mass = 1150 / (1 + (1.5 / 100))
= 1150 / 1.015
= 1133.5 kg/m³
For the fine aggregate:
SSD mass = 650 / (1 + (3.2 / 100))
= 650 / 1.032
= 629.96 kg/m³
Adjust the batch masses of each material by considering the SSD mass:
Adjusted batch mass = SSD mass / (1 - (Moisture content / 100))
For the cement:
Adjusted batch mass = 375 / (1 - (0 / 100))
= 375 kg/m³
For the fine aggregate:
Adjusted batch mass = 629.96 / (1 - (4.5 / 100))
= 629.96 / 0.9555
= 658.34 kg/m³
For the coarse aggregate:
Adjusted batch mass = 1133.5 / (1 - (3.0 / 100))
= 1133.5 / 0.97
= 1168.04 kg/m³
Calculate the adjusted batch mass for the total mixing water:
Since the total mixing water is already provided as 180 kg/m³, there is no adjustment needed.
Therefore, the adjusted batch masses of materials are as follows:
Cement: 375 kg/m³
Fine aggregate: 658.34 kg/m³
Coarse aggregate: 1168.04 kg/m³
Total mixing water: 180 kg/m³
To know more about masses visit
https://brainly.com/question/20579920
#SPJ11
Explain the effect of freezing thawing on concrete
Freezing and thawing can cause significant damage to concrete. The repeated expansion and contraction of water within the concrete pores can lead to cracking, spalling, and reduced structural integrity.
When water freezes, it expands, exerting pressure on the surrounding materials. In the case of concrete, the water present in its pores expands upon freezing, creating internal stress. As the ice melts during thawing, the water contracts, causing the concrete to shrink. This cyclic process weakens the concrete's structure over time. The expansion and contraction of water can lead to various types of damage. Cracking occurs as a result of the tensile stress caused by ice formation and the subsequent contraction. These cracks can allow more water to penetrate, exacerbating the problem. Spalling refers to the flaking or chipping of the concrete surface due to the pressure exerted by the expanding ice. Freezing and thawing cycles can be detrimental to concrete, resulting in cracking, spalling, and reduced durability.
Proper precautions and construction techniques, such as using air-entrained concrete and adequate curing, can help mitigate these effects. Regular maintenance and timely repairs are also essential to prolong the lifespan of concrete structures in freezing climates.
To know more about concrete visit:
https://brainly.com/question/32805749
#SPJ11
2. Determine the value of k when f(x)=2x¹ - 5x³+ Kx - 4 is divided by x-3, the remainder is 2.
The value of k when f(x) = 2x¹ - 5x³ + Kx - 4 is divided by x-3 and the remainder is 2, is K = 45.
To determine the value of k when f(x)=2x¹ - 5x³ + Kx - 4 is divided by x-3 and the remainder is 2, we can use the Remainder Theorem.
According to the Remainder Theorem, when a polynomial f(x) is divided by a linear factor x-a, the remainder is equal to f(a). In this case, the linear factor is x-3 and the remainder is 2.
So, to find the value of k, we substitute x=3 into the polynomial f(x) and set it equal to 2:
f(3) = 2(3)¹ - 5(3)³ + K(3) - 4 = 2
Now, let's solve for k:
2(3) - 5(3)³ + 3K - 4 = 2
6 - 135 + 3K - 4 = 2
-133 + 3K = 2
To isolate K, we add 133 to both sides:
3K = 2+ 133
3K = 135
Finally, divide both sides by 3 to solve for K:
K = 45
Learn more about remainder :
https://brainly.com/question/27749132
#SPJ11
Let A = {2, 3, 4, 5, 6, 7, 8} and R a relation over A. Draw the
directed graph and the binary matrix of R, after realizing that xRy
iff x−y = 3n for some n ∈ Z.
To draw the directed graph and binary matrix of the relation R over set A = {2, 3, 4, 5, 6, 7, 8}, where xRy if and only if x - y = 3n for some n ∈ Z, we need to identify which elements are related to each other according to this condition.
Let's analyze the relation R and determine the ordered pairs (x, y) where xRy holds true.
For x - y = 3n, where n is an integer, we can rewrite it as x = y + 3n.
Starting with the element 2 in set A, we can find its related elements by adding multiples of 3.
For 2:
2 = 2 + 3(0)
2 is related to itself.
For 3:
3 = 2 + 3(0)
3 is related to 2.
For 4:
4 = 2 + 3(1)
4 is related to 2.
For 5:
5 = 2 + 3(1)
5 is related to 2.
For 6:
6 = 2 + 3(2)
6 is related to 2 and 3.
For 7:
7 = 2 + 3(2)
7 is related to 2 and 3.
For 8:
8 = 2 + 3(2)
8 is related to 2 and 3.
Now, let's draw the directed graph, representing each element of A as a node and drawing arrows to indicate the relation between elements.
The directed graph of relation R:
```
2 ----> 4 ----> 6 ----> 8
↑ ↑ ↑
| | |
↓ ↓ ↓
3 ----> 5 ----> 7
```
Next, let's construct the binary matrix of R, where the rows represent the elements in the domain A and the columns represent the elements in the codomain A. We fill in the matrix with 1 if the corresponding element is related, and 0 otherwise.
Binary matrix of relation R:
```
| 2 3 4 5 6 7 8
---+---------------------
2 | 1 0 1 0 1 0 1
3 | 0 1 0 1 1 1 0
4 | 0 0 1 0 1 0 1
5 | 0 0 0 1 0 1 0
6 | 0 0 0 0 1 0 1
7 | 0 0 0 0 0 1 0
8 | 0 0 0 0 0 0 1
```
In the binary matrix, a 1 is placed in the (i, j) entry if element i is related to element j, and a 0 is placed otherwise.
Therefore, the directed graph and binary matrix of the relation R, where xRy if and only if x - y = 3n for some n ∈ Z, have been successfully represented.
Learn more about directed graph:
https://brainly.com/question/14762334
#SPJ11
The general wall thickness of a metallic tower was 0.12 inches on a 32 inches diameter carbon steel overhead line. The minimum thickness required is 0.14 inches. The current corrosion rate is 52 mpy. Another shutdown is scheduled to take place after one years.
The current thickness is 0.12 inches, the required thickness is 0.14 inches, and the corrosion rate is 52 mpy. After one year, the remaining thickness will be 0.068 inches, which is less than the required thickness. Therefore, another shutdown is necessary to meet the safety standards.
The general wall thickness of a metallic tower is 0.12 inches, and the diameter of the carbon steel overhead line is 32 inches. However, the minimum required thickness is 0.14 inches.
To determine the corrosion rate, we need to find the difference between the current thickness and the required thickness. In this case, the difference is 0.14 inches - 0.12 inches, which equals 0.02 inches.
Now, we know that the corrosion rate is 52 mpy (mils per year). To find out how much the thickness decreases in one year, we can multiply the corrosion rate by the time in years.
So, the thickness decrease in one year is 52 mpy * 1 year = 52 mils.
However, we need to convert mils to inches. Since there are 1000 mils in an inch, we divide 52 mils by 1000 to get the thickness decrease in inches: 52 mils / 1000 = 0.052 inches.
Now, we can calculate the remaining thickness after one year by subtracting the thickness decrease from the current thickness: 0.12 inches - 0.052 inches = 0.068 inches.
Finally, we compare the remaining thickness after one year (0.068 inches) with the required thickness (0.14 inches).
Since the remaining thickness (0.068 inches) is less than the required thickness (0.14 inches), another shutdown is needed to ensure the tower's safety and meet the minimum thickness requirement of 0.14 inches.
In summary, the current thickness is 0.12 inches, the required thickness is 0.14 inches, and the corrosion rate is 52 mpy. After one year, the remaining thickness will be 0.068 inches, which is less than the required thickness. Therefore, another shutdown is necessary to meet the safety standards.
Learn more about current on :
https://brainly.com/question/1100341
#SPJ11
The remaining life of metallic tower before the scheduled shutdown is approximately 0.3846 years.
To calculate the remaining life of the metallic tower before the scheduled shutdown, we need to consider the corrosion rate and the minimum required wall thickness.
Given data: Initial wall thickness (current): 0.12 inches
Minimum required wall thickness: 0.14 inches
Corrosion rate: 52 mpy (mils per year)
First, let's convert the corrosion rate from mpy to inches per year (ipy):
1 mil = 0.001 inches
Corrosion rate in inches per year (ipy) = 52 mpy * 0.001 inches/mil = 0.052 inches/year
Now, we can calculate the decrease in wall thickness per year due to corrosion:
Decrease in wall thickness per year = Corrosion rate in inches per year (ipy) = 0.052 inches/year
Next, let's calculate how many years it will take for the wall thickness to reach the minimum required thickness:
Time to reach minimum thickness = (Minimum required thickness - Initial thickness) / Decrease in wall thickness per year
Time to reach minimum thickness = (0.14 inches - 0.12 inches) / 0.052 inches/year
Time to reach minimum thickness = 0.02 inches / 0.052 inches/year
Time to reach minimum thickness ≈ 0.3846 years
Now, we have calculated the time it takes for the wall thickness to decrease to the minimum required thickness. However, we need to consider that another shutdown is scheduled to take place after one year. If the remaining life of the tower is less than one year, the tower should be scheduled for inspection and maintenance during the upcoming shutdown.
Remaining life of the tower before the scheduled shutdown = Minimum of (Time to reach minimum thickness, Time until the next shutdown)
Remaining life of the tower before the scheduled shutdown = Minimum of (0.3846 years, 1 year)
Since the minimum of 0.3846 years and 1 year is 0.3846 years, the remaining life of the metallic tower before the scheduled shutdown is approximately 0.3846 years. During the upcoming shutdown, the tower should be inspected, and if necessary, maintenance should be performed to address the corrosion and ensure the structural integrity of the tower.
Learn more about metallic tower from the given link:
https://brainly.com/question/29512069
#SPJ11
Needed urgently, with correct steps
Q3 (5 points) Find the general equation of the plane II that contains the points P(1, 2, 3), Q(1, 4, -2) and R(-1,0, 3).
The general equation of the plane II is 10x - 10y + 10z = 20.
To find the general equation of the plane that contains the points P(1, 2, 3), Q(1, 4, -2), and R(-1, 0, 3), you can follow these steps:
Step 1: Find two vectors that lie in the plane.
- Let's take vector PQ and vector PR.
- Vector PQ can be calculated as PQ = Q - P = (1 - 1, 4 - 2, -2 - 3) = (0, 2, -5).
- Vector PR can be calculated as PR = R - P = (-1 - 1, 0 - 2, 3 - 3) = (-2, -2, 0).
Step 2: Take the cross product of the two vectors found in step 1.
- The cross product of vectors PQ and PR can be calculated as PQ x PR = (2 * 0 - (-5) * (-2), (-5) * (-2) - 0 * (-2), 0 * 2 - 2 * (-5)) = (10, -10, 10).
Step 3: Use the normal vector obtained from the cross product to form the general equation of the plane.
- The normal vector to the plane is the cross product PQ x PR, which is (10, -10, 10).
- The equation of the plane can be written as Ax + By + Cz = D, where A, B, C are the components of the normal vector and D is a constant.
- Plugging in the values, we have 10x - 10y + 10z = D.
Step 4: Determine the value of D by substituting one of the given points.
- We can substitute the coordinates of point P(1, 2, 3) into the equation obtained in step 3.
- 10(1) - 10(2) + 10(3) = D.
- Simplifying the equation, we have 10 - 20 + 30 = D.
- D = 20.
Step 5: Write the final general equation of the plane.
- The general equation of the plane that contains the points P(1, 2, 3), Q(1, 4, -2), and R(-1, 0, 3) is 10x - 10y + 10z = 20.
So, the general equation of the plane II is 10x - 10y + 10z = 20.
To know more about equation click-
http://brainly.com/question/2972832
#SPJ11
Gasoline (s=0.58) flows in a 350-mm-diameter-pipe. The velocity is 1.80 m/s at 136 mm from the center of the pipe. Also, the velocity is 2.12 m/s at 100 mm from the center of the pipe. Determine the expected head loss if the pipe is 600 m long. Neglect minor losses.
The required expected head loss in the 600 m long pipe, neglecting minor losses, is approximately 0.9 meters.
Calculate the Reynolds number (Re) at both locations:
[tex]Re_1[/tex] = (720 * 1.80 * 0.35) / 0.0005 ≈ 1,238,400
[tex]Re_2[/tex] = (720 * 2.12 * 0.35) / 0.0005 ≈ 1,457,760
Calculate the friction factor (f) at both locations using the Reynolds number:
[tex]f_1[/tex] [tex]= 0.3164 / (1,238,400^{0.25} )[/tex]≈ 0.0094
[tex]f_2 = 0.3164 / (1,457,760^{0.25})[/tex] ≈ 0.0091
Calculate the head loss (hL) using the Darcy-Weisbach equation at both locations:
[tex]hL_1 = (0.0094* (600/0.35) * (1.80^2)) / (2 * 9.81)[/tex]≈ 2.67 m
[tex]hL_2 = (0.0091* (600/0.35) * (2.12^2)) / (2 * 9.81)[/tex]≈ 3.57 m
Calculate the total head loss:
Total head loss = 3.57 m - 2.67 m ≈ 0.9 m
Therefore, the expected head loss in the 600 m long pipe, neglecting minor losses, is approximately 0.9 meters.
Learn more about head loss here:
https://brainly.com/question/33289614
#SPJ4
7.8 An approximate equation for the velocity distribution in a pipe with turbulent flow is ye sili 19wans 2016 bus abrowa 101 svin oala vost V = enollsups Vmax To 911 m s(es. nism svi srl sus tarW. where Vmax is the centerline velocity, y is the distance from the wall of the pipe, ro is the radius of the pipe, and n is an exponent that depends on the Reynolds number and varies between 1/6 and 1/8 for most applications. Derive a formula for a as a 100 indigntuan function of n. What is a if n = 1/7?
The correct value of "a" as a function of "n" when n = 1/7.
To derive a formula for "a" as a function of "n," we start with the given equation:V = Vmax * (1 - (y / r)^(1/n))
Rearranging the equation, we isolate the term (y / r)^(1/n):
(y / r)^(1/n) = 1 - (V / Vmax)
To find "a," we raise both sides of the equation to the power of "n":
[(y / r)^(1/n)]^n = (1 - (V / Vmax))^n
Simplifying the left side:
y / r = (1 - (V / Vmax))^n
Finally, multiplying both sides by "r," we obtain the formula for "a":
a = r * (1 - (V / Vmax))^n
Now, if n = 1/7, we substitute this value into the formula:
a = r * (1 - (V / Vmax))^(1/7)
This gives the value of "a" as a function of "n" when n = 1/7.
Learn more about function here:
https://brainly.com/question/28793267
#SPJ8
A 50.0-liter cylinder is evacuated and filled with 5.00 kg of a gas containing 10.0 mole% N₂O and the balance N2. The gas temperature is 24.0°C. Use the appropriate compressibility chart to solve the following problems. What is the gauge pressure of the cylinder gas after the tank is filled? i 174.8 atm A fire breaks out in the plant where the cylinder is kept, and the cylinder valve ruptures when the gas gauge pressure reaches 273 atm. What was the gas temperature (°C) at the moment before the rupture occurred? i 113.4 °℃
Part a: The gauge pressure for the mixture of N2 and N2O at given conditions is 79.77 atm.
Part b: The temperature for the mixture of N2 and N2O at given conditions is 589.77 °C.
For N2
Critical temperature Tc = 126.2 K
Critical pressure Pc = 33.5 atm
For N2O
Critical temperature Tc = 309.5 K
Critical pressure Pc = 71.7 atm
10 mol% N2O and 90 mol% N2
For mixture
Critical temperature Tc' = 0.10*309.5 + 0.90*126.2 = 144.5 K
Critical pressure Pc' = 0.10*71.7 + 0.90*33.5 = 37.3 atm
Average molecular weight M = 0.10*44 + 0.90*28 = 29.6
Moles n = (5*1000 g) / (29.6 g/mol) = 169 mol
Part a
Reduced temperature Tr = (24+273)/144.5 = 2.06
Reduced volume Vr = (50L x 37.3 atm) / (169 mol x 144.5K x 0.0821 L-atm/mol-K)
= 0.93
Compressibility factor z = 0.98
P = znTR/V
= 0.98 x 169mol x (24+273)x 0.0821 L-atm/mol-K / 50L
= 80.77 atm
Gauge pressure = 80.77 - 1 = 79.77 atm
Part b
Reduced pressure Pr = (273atm)/(37.3 atm) = 7.32
Reduced volume Vr = 0.93
Compressibility factor z = 1.14
Temperature T = (273 atm x 50L) / (1.14 x 169 mol x 0.0821 L-atm/mol-K)
= 862.97 K
= 589.77 °C
Learn more About gauge from the given link
https://brainly.com/question/30425554
#SPJ11
What is the criteria for selecting a material as the main load bearing construction material?
The main criteria for selecting a material as the main load-bearing construction material include strength, stiffness, durability, cost-effectiveness, availability, and suitability for the specific project requirements.
When choosing a load-bearing construction material, several factors need to be considered. Strength refers to the material's ability to resist applied loads without significant deformation or failure. Stiffness relates to the material's resistance to deformation under load. Durability involves considering the material's resistance to environmental factors, such as corrosion or decay. Cost-effectiveness evaluates the material's price in relation to its performance and lifespan. Availability is crucial to ensure a reliable supply for the project. Suitability encompasses aspects like weight, fire resistance, ease of construction, and any specific requirements dictated by the project. The selection of a main load-bearing construction material requires considering multiple factors, including strength, stiffness, durability, cost, availability, and compatibility with the design and intended use of the structure.
Selecting the main load-bearing construction material involves assessing strength, stiffness, durability, cost-effectiveness, availability, and suitability. A comprehensive evaluation of these criteria helps determine the optimal material for the project.
To know more about stiffness visit:
https://brainly.com/question/31172851
#SPJ11
Help me please!!! I don’t know what to do. Applications of trigonometry
By applying the law of sine, the magnitude of both angles B and B' are as follows;
B = 109.73°
B' = 70.27°.
How to determine the magnitude of angles B and B'?In order to determine the magnitude of both angles B and B', we would apply the law of sine:
[tex]\frac{sinA}{a} =\frac{sinB}{b} =\frac{sinC}{c}[/tex]
By substituting the given parameters into the formula above, we have the following;
sinB'/10 = sin60/9.2
sinB'/10 = 0.8660/9.2
sinB'/10 = 0.0941
sinB' = 0.09413 × 10
B' = sin⁻¹(0.9413)
B' = 70.27°.
Now, we can determine the magnitude of angle B by using the formula for supplementary angles:
B + B' = 180
B + 70.27° = 180°
B = 180 - 70.27°
B = 109.73°.
Read more on law of sine here: https://brainly.com/question/30401249
#SPJ1
The ideal gasoline engine operates on the Otto cycle. use air as a working medium At initial conditions, the air pressure is 1.013 bar, the temperature is 37 ° C. When the piston moves up to the top dead center, the pressure is 20.268 bar. If this engine has a maximum pressure of 44.572 bar, the properties of the air are kept constant. at k =1.4, Cp=1.005 kJ/kgK, Cv = 0.718 kJ/kgK and R = 0.287 kJ/k
Find
1.What is the compression ratio of the Otto cycle?
2.What is the climatic temperature after the compression process?
3.How much work is used in the compression process?
4.What is the maximum process temperature?
5.How much heat goes into the process?
6.What is the direct temperature after expansion?
7.How much exactly is the work due to expansion?
1. The compression ratio of the Otto cycle is 44.
2. The final temperature after the compression process is 758.33 °C.
3. The work used in the compression process is 521.36 kJ/kg.
4. The maximum process temperature is 491.51 °C.
5. The heat input into the process is 466.47 kJ/kg.
6. The direct temperature after expansion is 24.09 °C.
7. The work due to expansion is -8.86 kJ/kg.
1. The compression ratio of the Otto cycle can be calculated by dividing the maximum pressure by the initial pressure. In this case, the maximum pressure is given as 44.572 bar and the initial pressure is 1.013 bar. Therefore, the compression ratio is 44.572/1.013 = 44.
2. To find the final temperature after the compression process, we can use the equation T2 = [tex]T1 * (P2/P1)^{((k-1)/k)[/tex], where T1 and P1 are the initial temperature and pressure, and T2 and P2 are the final temperature and pressure. Plugging in the given values, we have T2 = 37 * [tex](20.268/1.013)^{((1.4-1)/1.4)[/tex] = 758.33 °C.
3. The work used in the compression process can be calculated using the equation W = [tex]C_v[/tex] * (T2 - T1), where [tex]C_v[/tex] is the specific heat at constant volume. Plugging in the values, we get [tex]W = 0.718 * (758.33 - 37) = 521.36 kJ/kg.[/tex]
4. The maximum process temperature can be found using the equation [tex]T_{max} = T1 * (V1/V2)^{(k-1)[/tex], where V1 and V2 are the initial and final volumes.
Since the properties of air are kept constant, the compression process is isentropic and
[tex]V1/V2 = (P2/P1)^{(1/k)} = (44.572/1.013)^{(1/1.4)} = 5.02.[/tex]
Plugging in the value, we have [tex]T_{max} = 37 * 5.02^{(1.4-1)[/tex] = 491.51 °C.
5. The heat input into the process can be calculated using the equation [tex]Q = C_p * (T_{max} - T1)[/tex], where C_p is the specific heat at constant pressure. Plugging in the values, we get [tex]Q = 1.005 * (491.51 - 37) = 466.47 kJ/kg.[/tex]
6. The direct temperature after expansion can be found using the same equation as in step 2, but with the final pressure as 1.013 bar (initial pressure) and the initial pressure as 44.572 bar (maximum pressure). Plugging in the values, we have [tex]T_{direct} = 37 * (1.013/44.572)^{((1.4-1)/1.4)[/tex] = 24.09 °C.
7. The work due to expansion can be calculated using the equation[tex]W = C_v * (T_{direct} - T1)[/tex], where T_direct is the direct temperature after expansion. Plugging in the values, we get[tex]W = 0.718 * (24.09 - 37) = -8.86[/tex] kJ/kg (negative value indicates work done by the system).
Learn more about compression ratio
https://brainly.com/question/13152665
#SPJ11
"Reflecting surfaces need to be about the same size as the sound waves that they are reflecting. Therefore, if you wanted to make a reflector that was capable of reflecting a 60 Hz sound what would the minimum size of the reflector need to be?
A. 20 ft. B. 15 ft. C. 10 ft. D. SAL. 28.
The minimum size of the reflector needed to reflect a 60 Hz sound wave would be approximately A)20 ft.
The reason for this is that in order for a reflecting surface to effectively reflect sound waves, it needs to be about the same size as the wavelength of the sound wave. The wavelength of a sound wave is determined by its frequency, which is the number of cycles the wave completes in one second. The formula to calculate wavelength is wavelength = speed of sound/frequency.
In this case, the frequency is 60 Hz. The speed of sound in air is approximately 343 meters per second. Therefore, the wavelength of a 60 Hz sound wave would be approximately 5.7 meters.
To convert meters to feet, we divide by 0.3048 (1 meter = 3.28084 feet). Therefore, the minimum size of the reflector needed would be approximately 18.7 feet.
Hence the correct option is A)20 ft.
For more similar questions on sound wave
brainly.com/question/1417453
#SPJ8