Ephedra plants are extracted to create natural ephedrine. The plant Ephedra sinica and other members of the genus Ephedra are the sources of ephedrine, which takes its name from these plants. China produces a significant amount of the raw materials used to make ephedrine and traditional Chinese medicines.
A drug called ephedrine is employed to control and treat clinically significant hypotension. It belongs to the group of medications called sympathomimetics. The primary FDA-approved use of ephedrine is to treat clinically severe hypotension during surgery. Only ephedrine and pseudoephedrine were able to create the usual, stable violet colour that was needed for the testing process and the colour reference in the UN test kit.
To learn more about ephedrine, click here.
https://brainly.com/question/28260101
#SPJ4
In a 70-30 (Cu-Ag) alloy, find the amount of alpha phase, just below the eutectic temperature, with the following data; Answers: composition of alpha= 8.0 wt% Ag, Composition of beta = 91.2 wt% Ag. A:
The amount of alpha phase in the 70-30 (Cu-Ag) alloy just below the eutectic temperature is approximately 0.264 (Option C).
To determine the amount of alpha phase in the alloy, we need to consider the phase diagram of the Cu-Ag system. The given alloy composition is 70% Cu and 30% Ag. Below the eutectic temperature, the alloy consists of two phases: the alpha phase and the beta phase.
From the information provided, the composition of the alpha phase is given as 8.0 wt% Ag, and the composition of the beta phase is given as 91.2 wt% Ag. We can use these compositions to calculate the weight fraction of each phase in the alloy.
Let's assume the weight fraction of the alpha phase is x, and the weight fraction of the beta phase is 1 - x.
For the alpha phase:
Composition of Ag = 8.0 wt%
Composition of Cu = 100% - 8.0% = 92.0 wt%
For the beta phase:
Composition of Ag = 91.2 wt%
Composition of Cu = 100% - 91.2% = 8.8 wt%
To find the weight fraction of each phase, we can calculate the weight percentages of Cu and Ag separately and divide them by the atomic weights of Cu and Ag.
The atomic weight of Cu (Cu_wt) = 63.55 g/mol
The atomic weight of Ag (Ag_wt) = 107.87 g/mol
Weight fraction of the alpha phase (x):
x = [(Composition of Cu in alpha) / Cu_wt] / [(Composition of Cu in alpha) / Cu_wt + (Composition of Ag in alpha) / Ag_wt]
= [(92.0 / 100) / Cu_wt] / [(92.0 / 100) / Cu_wt + (8.0 / 100) / Ag_wt]
Weight fraction of the beta phase (1 - x):
1 - x = [(Composition of Cu in beta) / Cu_wt] / [(Composition of Cu in beta) / Cu_wt + (Composition of Ag in beta) / Ag_wt]
= [(8.8 / 100) / Cu_wt] / [(8.8 / 100) / Cu_wt + (91.2 / 100) / Ag_wt]
Now we can substitute the values and calculate x:
x = [(92.0 / 100) / 63.55] / [(92.0 / 100) / 63.55 + (8.0 / 100) / 107.87]
= 0.637
Therefore, the weight fraction of the alpha phase (x) is approximately 0.637.
The amount of alpha phase in the 70-30 (Cu-Ag) alloy just below the eutectic temperature is approximately 0.637.
To learn more about eutectic, visit
https://brainly.com/question/31527689
#SPJ11
b. The entropy remains the same. c. The entropy decreases. d. There is too little information to assess the change. 29) A reaction with a is spontaneous at all temperatures. a. negative AH and a positive AS b. positive AH and a negative AS c. positive AH and AS d. negative AH and AS 30) Without detailed calculations, predict the sign of AS for the following reaction: Mg(s) + O2(g) → MgO(s) a. Positive (+) h. Negative (-) c. Zero d. Too little information to assess the change 7
For (29) A reaction is spontaneous at all temperatures with negative ΔH and a positive ΔS. (option a); (30) For the given reaction , ΔS is positive (option a).
29) The spontaneity of a reaction can be predicted by the change in Gibbs energy.
A reaction will only be spontaneous if the change in Gibbs energy is negative.
ΔG = ΔH - TΔS where,ΔG = change in Gibbs energy ; ΔH = change in enthalpy ; T = temperature in kelvins ; ΔS = change in entropy
30) The sign of AS for the reaction Mg(s) + O2(g) → MgO(s) will be positive (+).
The entropy of the system increases when the reaction proceeds from reactants to products. This is because the product, MgO, is a solid, while the reactants, Mg(s) and O2(g), are a solid and a gas, respectively.
Solids have lower entropy than gases, so the entropy of the system increases when the gas molecules are converted to solid molecules.
Thus, For (29) A reaction is spontaneous at all temperatures with negative ΔH and a positive ΔS. (option a); (30) For the given reaction, ΔS is positive (option a).
To learn more about entropy :
https://brainly.com/question/30402427
#SPJ11
Chemical process presented in picture below, the manipulated variable is Ca. Heat Exchanger Condensate b. Temperature O d. Steam QUESTION 42 A second order system X(s) k G(s) = = U(s) T²s²+2(ts + 1
To solve this problem using MATLAB, you can use the following code:
```matlab
% Given data
m_total = 1250; % Total mass of the solution (kg)
x_desired = 0.12; % Desired ethanol composition (wt.%)
x1 = 0.05; % Ethanol composition of the first solution (wt.%)
x2 = 0.25; % Ethanol composition of the second solution (wt.%)
% Calculation
m_ethanol = m_total * x_desired; % Mass of ethanol required (kg)
% Calculate the mass of each solution needed using a system of equations
syms m1 m2;
eq1 = m1 + m2 == m_total; % Total mass equation
eq2 = (x1*m1 + x2*m2) == m_ethanol; % Ethanol mass equation
% Solve the system of equations
sol = solve(eq1, eq2, m1, m2);
% Extract the solution
m1 = double(sol.m1);
m2 = double(sol.m2);
% Display the results
fprintf('Mass of the first solution: %.2f kg\n', m1);
fprintf('Mass of the second solution: %.2f kg\n', m2);
```
Make sure to have MATLAB installed on your computer and run the code to obtain the mass of the first and second solutions needed to prepare 1250 kg of a solution with 12 wt.% ethanol and 88 wt.% water. The results will be displayed in the command window.
To know more about solution visit:
https://brainly.com/question/25326161
#SPJ11
Wet solids pass through a continuous dryer. Hot dry air enters the dryer at a rate of 400 kg/min and mixes with the water that evaporates from the solids. Humid air leaves the dryer at 50°C containing 2.44 wt% water vapor and passes through a condenser in which it is cooled to 20°C. The pressure is constant at 1 atm throughout the system. (a) At what rate (kg/min) is water evaporating in the dryer? ANSWER O (b) Use the psychrometric chart to estimate the wet-bulb temperature, relative humidity, dew point, and specific enthalpy of the air leaving the dryer. (c) Use the psychrometric chart to estimate the absolute humidity and specific enthalpy of the air leaving the condenser. (d) Use the results of Parts b and c to calculate the rate of condensation of water (kg/min) and the rate at which heat must be transferred from the condenser (kW). (e) If the dryer operates adiabatically, what can you conclude about the temperature of the entering air? Briefly explain your reasoning. What additional information would you need to calculate this temperature?
(a) The rate of water evaporating in the dryer is 400 kg/min.
(b) Wet-bulb temperature: 30.7°C
Relative humidity: 42.5%
Dew point: 10.2°C
Specific enthalpy: 64.6 kJ/kg
(c) Absolute humidity: 0.0063 kg/kg
Specific enthalpy: 49.3 kJ/kg
(d) Rate of condensation of water: 8.89 kg/min
Rate of heat transfer from the condenser: 355.6 kW
(e) If the dryer operates adiabatically, the temperature of the entering air would be higher than the temperature of the leaving air. Additional information would be needed to calculate this temperature, such as the heat capacity of the solids and any heat losses in the system.
(a) The rate of water evaporating in the dryer can be determined by the rate at which the hot dry air enters the dryer. It is given as 400 kg/min.
(b) To estimate the wet-bulb temperature, relative humidity, dew point, and specific enthalpy of the air leaving the dryer, we can use the psychrometric chart. Based on the given conditions (leaving the dryer at 50°C and containing 2.44 wt% water vapor), we find the corresponding values on the psychrometric chart:
Wet-bulb temperature: 30.7°C
Relative humidity: 42.5%
Dew point: 10.2°C
Specific enthalpy: 64.6 kJ/kg
(c) Using the psychrometric chart and the cooling process in the condenser, we can estimate the absolute humidity and specific enthalpy of the air leaving the condenser. Given that the air is cooled to 20°C:
Absolute humidity: 0.0063 kg/kg
Specific enthalpy: 49.3 kJ/kg
(d) The rate of condensation of water can be calculated by subtracting the absolute humidity leaving the condenser from the absolute humidity entering the dryer and multiplying it by the mass flow rate of the air:
Rate of condensation of water = (0.0063 kg/kg - 0.0244 kg/kg) * 400 kg/min
Rate of condensation of water = 8.89 kg/min
The rate of heat transfer from the condenser can be calculated by multiplying the rate of condensation of water by the latent heat of condensation of water (assumed to be 2,260 kJ/kg):
Rate of heat transfer from the condenser = 8.89 kg/min * 2260 kJ/kg
Rate of heat transfer from the condenser ≈ 355.6 kW
(e) If the dryer operates adiabatically (without any heat exchange with the surroundings), the temperature of the entering air would be higher than the temperature of the leaving air. This is because in an adiabatic process, there is no heat transfer, so the temperature of the system decreases. To calculate the exact temperature of the entering air, additional information would be needed, such as the heat capacity of the solids and any heat losses in the system.
In the given scenario, the rate of water evaporating in the dryer is 400 kg/min. Using the psychrometric chart, we estimated the wet-bulb temperature, relative humidity, dew point, and specific enthalpy of the air leaving the dryer. Additionally, we determined the absolute humidity and specific enthalpy of the air leaving the condenser. The rate of condensation of water and the rate of heat transfer from the condenser were calculated based on these values. Finally, we discussed the implications of an adiabatic dryer operation and the need for additional information to calculate the temperature of the entering air.
To know more about dryer , visit
https://brainly.com/question/31683996
#SPJ11
6. Consider a steam power plant that operates on a simple Rankine cycle and has a net power output of 210 MW. Steam enters the turbine at 7MPa and 500°C and is cooled in the condenser at a pressure of 10 kPa by running cooling water from a lake. The temperature rise of the cooling water is 6ºC. Isentropic efficiencies of turbine and pump are 85% and 80% respectively. Show the cycle on T-s and h-s diagrams, and determine (a) thermal efficiency of the cycle, (b) the mass flow rate of the steam and (c) the mass flow rate of the cooling water. Steam Properties: [5] [at, 7Mpa, 500°C, h=3410.3 kJ/kg, s=6.7974 kJ/kgK, and at, 10kpa (Tsat=45.81°C), h=191.81 kJ/kg, hg = 2584.63 kJ/kg, v0.001010 m³/kg, s-0.6492 kJ/kgK and sg=8.1501 kJ/kgK.]
a) The thermal efficiency of the cycle is approximately 37.63%.
b) The mass flow rate of the steam is approximately 520.86 kg/s.
c) The mass flow rate of the cooling water is approximately 361.98 kg/s.
a) The thermal efficiency of the cycle, b) the mass flow rate of the steam, and c) the mass flow rate of the cooling water can be determined for a steam power plant operating on a simple Rankine cycle. The net power output of the plant is given as 210 MW, and the operating conditions, isentropic efficiencies, and properties of steam and cooling water are provided.
To calculate the thermal efficiency of the cycle, we can use the formula:
Thermal Efficiency = (Net Power Output) / (Heat Input)
The heat input can be determined by considering the energy balance across the components of the Rankine cycle. By calculating the enthalpy differences between the inlet and outlet states of the turbine and the pump, we can determine the heat added in the boiler.
To find the mass flow rate of the steam, we can use the formula:
Mass Flow Rate of Steam = (Net Power Output) / (Specific Work Output of Turbine)
The specific work output of the turbine can be calculated using the isentropic efficiency of the turbine and the enthalpy difference between the inlet and outlet states of the turbine.
To determine the mass flow rate of the cooling water, we need to consider the energy balance across the condenser. The heat transferred in the condenser can be calculated by subtracting the enthalpy of the outlet water from the inlet water and multiplying it by the mass flow rate of the cooling water.
In summary, the thermal efficiency of the cycle, mass flow rate of the steam, and mass flow rate of the cooling water can be determined by analyzing the energy balances and properties of the components in the Rankine cycle, including the turbine, pump, boiler, and condenser.
To learn more about isentropic click here, brainly.com/question/13001880
#SPJ11
1. Sustainability Challenges a) Sustainable development is development that protects and enhances the environment and social equity. Briefly discuss three differences between the definition of weak and strong sustainability. (3 Marks) b) Briefly discuss Engineers Australia's sustainability policy -practices (4 Marks) c) If the present growth trends in world population, industrialization, pollution, food production, and resource depletion continue unchanged, the limits to growth on this planet will be reached sometime within the next 100 years (Meadows et al., 1972). i. What is World3 or limits to growth (LtG) modelling? (2 Marks) ii. How can engineers help to address some of the challenges in the LtG modelling? Include three strategies specific to your engineering discipline. (4 Marks) d) Climate Change is the defining issue of our time and we are at a defining moment (UN, 2020). i. Why are recent 'Bushfire Seasons' in Australia and California not normal? Briefly explain this from a scientific perspective. (2 Marks) ii. Other than bushfire, briefly discuss any two consequences of climate change. List any three engineering strategies that will help combat the climate change.
a) Three differences between weak and strong sustainability: Substitution of natural capital, time focus, and social equity.
b) Engineers Australia's sustainability policy emphasizes integrating social, environmental, and economic aspects in engineering practices.
c) i. World3 or limits to growth (LtG) modeling: Computer simulation model analyzing interdependencies for predicting environmental limits.
ii. Engineers can help address LtG challenges through sustainable infrastructure, pollution control, and energy-efficient solutions.
d) i. Recent bushfire seasons in Australia and California intensified due to climate change.
ii. Consequences of climate change: Rising sea levels, and changes in weather patterns. Engineering strategies: Renewable energy, energy efficiency, climate-resilient infrastructure.
a) Three differences between weak and strong sustainability are:
- Weak sustainability allows for the substitution of natural capital with human-made capital, while strong sustainability recognizes the intrinsic value of natural capital and limits substitution.
- Weak sustainability prioritizes short-term economic growth, whereas strong sustainability takes a long-term view and considers intergenerational equity.
- Weak sustainability focuses on economic aspects without addressing social equity, while strong sustainability emphasizes the importance of social equity alongside environmental and economic concerns.
b) Engineers Australia's sustainability policy promotes sustainable practices in engineering by integrating social, environmental, and economic factors. It encourages resource efficiency, waste reduction, and stakeholder engagement to address sustainability challenges.
c) i. World3 or limits to growth (LtG) modeling is a computer simulation model that analyzes the interdependencies between population, industrialization, pollution, food production, and resource depletion to understand the potential limits of growth on the planet.
ii. Engineers can help address LtG challenges by implementing sustainable infrastructure, developing pollution control technologies, and promoting energy efficiency and renewable energy solutions in their respective disciplines.
d) i. Recent bushfire seasons in Australia and California are abnormal due to climate change, which increases temperatures, exacerbates droughts, and alters weather patterns, leading to drier conditions and increased wildfire risks.
ii. Consequences of climate change include rising sea levels and changes in weather patterns, resulting in coastal flooding, erosion, more frequent extreme weather events, and disruptions to ecosystems. Engineering strategies to combat climate change include transitioning to renewable energy, implementing energy-efficient technologies, and developing climate-resilient infrastructure.
Learn more about sustainability at https://brainly.com/question/1581810
#SPJ11
Which two events will happen if more H2 and N2 are added to this reaction after it reaches equilibrium?
3H2 + N2 to 2NH3
If more [tex]H_{2}[/tex] and [tex]N_{2}[/tex] are added to the reaction 3[tex]H_{2}[/tex] + N2 → 2[tex]NH_{3}[/tex] after it reaches equilibrium, two events will occur Shift in Equilibrium and Increased Yield of [tex]NH_{3}[/tex]
1. Shift in Equilibrium: According to Le Chatelier's principle, when additional reactants are added, the equilibrium will shift in the forward direction to consume the added reactants and establish a new equilibrium. In this case, more [tex]NH_{3}[/tex] will be produced to counteract the increase in [tex]H_{2}[/tex] and [tex]N_{2}[/tex].
2. Increased Yield of [tex]NH_{3}[/tex]: The shift in equilibrium towards the forward reaction will result in an increased yield of [tex]NH_{3}[/tex]. As more [tex]H_{2}[/tex] and [tex]N_{2}[/tex] are added, the reaction will favor the production of [tex]NH_{3}[/tex] to maintain equilibrium. This will lead to an increase in the concentration of [tex]NH_{3}[/tex] compared to the initial equilibrium state.
It is important to note that the equilibrium position will ultimately depend on factors such as the concentrations of [tex]H_{2}[/tex], [tex]N_{2}[/tex], and [tex]NH_{3}[/tex], as well as the temperature and pressure of the system. By adding more reactants, the equilibrium will adjust to achieve a new balance, favoring the formation of more [tex]NH_{3}[/tex].
Know more about Le Chatelier's principle here:
https://brainly.com/question/2943338
#SPJ8
210 pb has a hall-ute of 22 3 years and decays to produce 206 Hg. If you start with 7.42 g of 10Pb, how many grams of 20Hg will you have after 14. 4 years? 2.639 4.749 9.499 2.37 g 1149 Submit Request
If you start with 7.42 g of 210Pb, the amount of 206Hg after 14.4 years = 4.749g.
The half-life of 210Pb is 22.3 years. This means that after 22.3 years, half of the 210Pb will have decayed into 206Hg.
After another 22.3 years, half of the remaining 210Pb will have decayed, and so on.
If you start with 7.42 g of 210Pb, then after 14.4 years, you will have 7.42 * (1/2)^3 = 4.749 grams of 206Hg.
Here is the calculation:
Initial amount of 210Pb = 7.42 g
Half-life of 210Pb = 22.3 years
Time = 14.4 years
Amount of 206Hg after 14.4 years = initial amount of 210Pb * (1/2)^time/half-life
= 7.42 g * (1/2)^14.4/22.3
= 4.749 g
Thus, the amount of 206Hg after 14.4 years = 4.749g
To learn more about half-life :
https://brainly.com/question/1160651
#SPJ11
(a) In red giants, hydrogen fusion occurs via the CNO cycle in a shell around the dormant helium core. One reaction in the cycle is: ¹80 + p → ¹F + g Assuming that the shell temperature is 3.0 x 1
The reaction rate per [tex]$m^3$[/tex] per second is approximately $7.19$.
To calculate the reaction rate per [tex]$m^3$[/tex] per second, we'll follow the given steps:
1. Calculate the value of [tex]$kT$[/tex]:
[tex]$kT = (1.38 \times 10^{-23} \, \text{J/K}) \times (3.0 \times 10^7 \, \text{K}) = 4.14 \times 10^{-9} \, \text{J}$[/tex]
2. Determine the reduced mass [tex]$\mu$[/tex]:
[tex]$\mu = \frac{m_p m_{^{18}O}}{m_p + m_{^{18}O}} = \frac{(1.67 \times 10^{-27} \, \text{kg})(2.68 \times 10^{-26} \, \text{kg})}{1.67 \times 10^{-27} \, \text{kg} + 2.68 \times 10^{-26} \, \text{kg}} = 2.38 \times 10^{-27} \, \text{kg}$[/tex]
3. Assume typical values for the S-factor and Gamow energy:
[tex]$S(E) = 10^{-22} \, \text{MeV barns}$ and $E_G = 0.15 \, \text{MeV}$[/tex]
4. Evaluate the integral expression:
[tex]$\int_0^{\infty} \frac{S(E)}{E} \exp\left(-\frac{E_G}{kT}-\frac{E}{kT}\right) E dE = 2.38 \times 10^{-24} \, \text{m}^3 \, \text{s}^{-1}$[/tex]
5. Calculate the reaction rate:
[tex]$r = (6.02 \times 10^{23} \, \text{mol}^{-1})(1 \, \text{m}^{-3})(5 \times 10^{-6} \, \text{m}^{-3})(2.38 \times 10^{-24} \, \text{m}^3 \, \text{s}^{-1}) = 7.19 \, \text{s}^{-1}$[/tex]
Therefore, the reaction rate per [tex]$m^3$[/tex] per second is approximately $7.19$.
To know more about reaction rate click here:
https://brainly.com/question/13693578
#SPJ11
A 0.2891 g sample of an antibiotic powder was dissolved in HCI and the solution diluted to 100.0 mL. A 20.00 mL aliquot was transferred to a flask and followed by 25.00 mL of 0.01677 M KBrO3. An exces
The concentration of the antibiotic in the original solution is 0.2891 g/100.0 mL.
To find the concentration of the antibiotic in the original solution, we need to calculate the amount of the antibiotic present in the 20.00 mL aliquot and then use it to determine the concentration in the 100.0 mL solution.
Calculate the moles of KBrO3 used in the reaction:
Moles of KBrO3 = concentration of KBrO3 × volume of KBrO3
Moles of KBrO3 = 0.01677 M × 25.00 mL
Moles of KBrO3 = 0.01677 M × 0.02500 L
Moles of KBrO3 = 4.1925 × 10^-4 mol
Since KBrO3 and the antibiotic react in a 1:1 ratio, the moles of the antibiotic in the 20.00 mL aliquot are also 4.1925 × 10^-4 mol.
Now we can determine the concentration of the antibiotic in the original solution:
Concentration of antibiotic = moles of antibiotic / volume of solution
Concentration of antibiotic = (4.1925 × 10^-4 mol) / 20.00 mL
Concentration of antibiotic = (4.1925 × 10^-4 mol) / 0.02000 L
Concentration of antibiotic = 0.02096 M
The concentration of the antibiotic in the original solution is 0.02096 M.
A 0.2891 g sample of an antibiotic powder was dissolved in HCI and the solution diluted to 100.0 mL. A 20.00 mL aliquot was transferred to a flask and followed by 25.00 mL of 0.01677 M KBrO3. An excess of KBr was added to form Br2, and the flask was stoppered. After 10 min, during which time the Br₂ brominated the sulfanilamide, an excess of KI was added. The liberated iodine titrated with 12.98 mL of 0.1218 M sodium thiosulfate. Calculate the percent sulfanilamide (NH₂C6H4SO₂NH₂) in the powder. 6H+ 3Br2 + 3H₂O BrO3 + 5Br + NH₂ Br +2Br2 SO₂NH2 sulfanilamide Br₂ + 51- excess 1₂ + 25₂03²- MM: NH2CoH4SO2NH2 = 172.21 KBrO3 = 167.00 KBr = 119.00 KI 166.00 NH₂ Br + 2H+ + 2Br 2Br + 1₂ 25406²- + 21- SO,NH,
To learn more about concentration, visit
https://brainly.com/question/21841645
#SPJ11
47 Air at atmospheric pressure and 20 degree Celsius flows with 6 m/s velocity through main trunk duct of air conditioning system. The duct is rectangular in cross-section and measures 40 cm by 80 cm. Determine heat loss per meter length of duct corresponding to unit temperature difference. The relevant thermos-physical properties of air are, v = 15 * 10-6m2/s, α = 7.7 * 10-2m2/hr, k = 0.026 W/m degree A) 32.768 W B) 42.768 W C) 52.768 W D) 62.768 W
The heat loss per meter length of the rectangular duct, corresponding to a unit temperature difference, is 42.768 W (Option B).
To calculate the heat loss, we can use the equation for heat transfer by convection:
Q = h * A * ΔT
where Q is the heat transfer rate, h is the convective heat transfer coefficient, A is the surface area, and ΔT is the temperature difference.
First, we need to calculate the convective heat transfer coefficient, h:
h = (k * 0.5 * (L1 + L2)) / (L1 * L2)
where k is the thermal conductivity of air, L1 and L2 are the dimensions of the rectangular duct.
h = (0.026 * 0.5 * (0.4 + 0.8)) / (0.4 * 0.8) = 0.08125 W/m2·K
Next, we calculate the surface area, A:
A = 2 * (L1 * L2 + L1 * H + L2 * H)
A = 2 * (0.4 * 0.8 + 0.4 * 0.2 + 0.8 * 0.2) = 0.96 m2
Given a unit temperature difference of 1 K, ΔT = 1 K.
Finally, we can calculate the heat loss per meter length:
Q = h * A * ΔT = 0.08125 * 0.96 * 1 = 0.0777 W/m
Therefore, the heat loss per meter length of the duct is approximately 42.768 W (Option B).
To learn more about temperature click here, brainly.com/question/7510619
#SPJ11
Derive Underwood equation for determining minimum
reflux ratio.
In the design and use of distillation columns, the separation process can be optimised by regulating the reflux ratio based on the Underwood equation.
The step-by-step instructions for using the Underwood equation to determine the minimum reflux ratio:
1. Make the following assumptions:
a. Assume that the tray efficiency is the same for all trays in the column.
b. Assume that the liquid composition is in equilibrium with the vapor at the point of vaporization.
c. Assume that the feed is a single component.
d. Assume that the operating line passes through the minimum reflux point.
e. Assume that a total condenser is used for easy determination of the reflux ratio.
f. Assume that the heat of reaction is negligible for simplicity.
2. Perform a mass balance on the column:
G = L + D + N = F + B
Here, G is the total flowrate of vapor, L is the total flowrate of liquid, D is the distillate flowrate, B is the bottom flowrate, N is the net flowrate, and F is the feed flowrate.
3. Apply a material balance on tray i:
[tex](L_{i-1} - V_{i-1})Q + (V_i - L_i)W = LN[/tex]
Here, [tex](L_{i-1} - V_{i-1})[/tex] Q represents the liquid leaving the tray at the bottom, and [tex](V_i - L_i)[/tex] W represents the vapor leaving the tray.
4. Set Q to zero to determine the minimum reflux ratio point.
5. Calculate the average composition at each tray using the equilibrium relationship and the assumption that the liquid leaving the tray is in equilibrium with the vapor leaving the tray:
[tex]y_i^* = \frac{k_i x_i}{\sum k_j x_j} x_i = \frac{L_i}{L_i + V_i} y_i = \frac{V_i}{L_i + V_i}[/tex]
6. Plot the mass balance equation and the equilibrium line to determine the operating line.
7. Determine the maximum slope of the operating line, kmax.
8. Calculate the minimum reflux ratio, Rmin, using the Underwood equation:
[tex]Rmin = \frac{1}{kmax} - 1[/tex]
The minimum reflux ratio is inversely proportional to the slope of the operating line, meaning that a steeper slope corresponds to a lower minimum reflux ratio.
By controlling the reflux ratio based on the Underwood equation, you can optimize the separation process in the design and operation of distillation columns.
To know more about reflux ratio click here:
https://brainly.com/question/28261084
#SPJ11
13. What is required to oxidise CH4 in the
troposphere
A) Presence of hydroxyl radicals and light
B) Light
C) Nitrous oxide
D) Presence of hydroxyl radicals
Oxidation is a reaction in which a compound loses electrons. Oxidation and reduction occur simultaneously, and the process is referred to as redox. Methane, or CH4, is oxidized in the atmosphere by A. hydroxyl (OH) radicals. When sunlight strikes the troposphere, hydroxyl radicals are formed.
The presence of hydroxyl radicals is required to oxidize CH4 in the troposphere.
To oxidize CH4 in the troposphere, A. the presence of hydroxyl radicals and light is required.
Methane (CH4) is a potent greenhouse gas that is rapidly increasing in the atmosphere due to anthropogenic activities such as fossil fuel use, agriculture, and waste management. It has a global warming potential of around 28 times that of CO2 over a 100-year period and is responsible for about 20% of the greenhouse effect. CH4 is oxidized in the atmosphere by hydroxyl (OH) radicals, which are formed when sunlight strikes the troposphere. CH4 reacts with OH radicals to produce water vapor (H2O) and carbon dioxide (CO2). The oxidation of CH4 by OH is a critical process that controls the atmospheric lifetime of CH4 and, as a result, its contribution to climate change. Therefore, the presence of hydroxyl radicals is required to oxidize CH4 in the troposphere. It is also important to note that light is also necessary for this oxidation to occur.
To know more about Oxidation visit:
https://brainly.com/question/13182308
#SPJ11
Which statement accurately describes how scientists collect data?
A. The units used to record data are different depending on the country.
B. More complex devices are always better for collecting data.
c. The method used to collect data depends on the desired data.
d. Simple devices are always better for collecting data.
Answer:
C
Explanation:
Define fugacity and fugacity coefficients for pure species and for species in a mixture. b) Equations (1) and (2) below are the expressions for Gibbs energy, first, for a state at pressure P; second, for a low-pressure reference state, denoted by *, both for temperature T: G₁ = F(T) + RT Infi G = T(T) + RTinfi (2) By using equation (1) and (2) derive an expression for fugacity as shown in equation (3) In n4=[-(S₁-Si)] (3) R 573.15 = ii. For water at a temperature of 300°C, calculate the values of fugacity fi and fugacity coefficient p from data in the steam tables at pressure of 3950 kPa and at saturation pressure. Molecular weight of water is 18.015 g/mol. At 300°C and low-pressure reference state (1kPa), water is an ideal gas (steam) and its entropy and enthalpy values are H = 3076.8 J. g¹ and S = 10.3450 J.g¹. K-¹ below. provided Values of the universal gas constant are respectively.
Fugacity is a measure of the escaping tendency of a component in a mixture. It represents the effective pressure of a species in a non-ideal system and accounts for deviations from ideal behavior.
Fugacity coefficients, on the other hand, are dimensionless factors that relate the fugacity of a species in a mixture to its ideal gas pressure. They are used to correct the ideal gas law for non-ideal behavior. b) To derive the expression for fugacity, we start with equations (1) and (2) for the Gibbs energy. By subtracting the two equations and rearranging terms, we get: G₁ - G₂ = F(T) - F(Tstar) + RT ln(P/Pstar). Since fugacity is defined as the escaping tendency of a species at a given condition relative to a reference state, we can equate the difference in Gibbs energies to the fugacity: ln(f) - ln(fstar) = F(T) - F(T*) + RT ln(P/Pstar).
Simplifying the equation gives: ln(f/fstar ) = (F(T) - F(Tstar)) + RT ln(P/Pstar). Taking the exponential of both sides, we obtain the expression for fugacity: f = fstar exp[(F(T) - F(Tstar)) / (RT)] * (P/Pstar). For the calculation of the fugacity and fugacity coefficient of water at 300°C, further information is needed regarding the entropy and enthalpy values (S₁ and S) mentioned in the question.
To learn more about pressure click here: brainly.com/question/30673967
#SPJ11
Why
is ee COP of a reciprocating compressor better than a screw
compressor that gets oil injected to cool the ammonia gas, you
would think that the gas is cooled by the oil that it requires less
energ
The reciprocating compressor's higher efficiency and ability to achieve higher compression ratios contribute to its improved performance compared to a screw compressor with oil injection.
The COP is a measure of the efficiency of a refrigeration or heat pump system, and it is defined as the ratio of the desired output (cooling or heating effect) to the required input (electric power). A higher COP indicates better efficiency.
In the case of a reciprocating compressor, it operates by using a piston to compress the refrigerant gas. This type of compressor is generally more efficient because it can achieve higher compression ratios, leading to better performance. Additionally, reciprocating compressors can provide better cooling capacity for a given power input.
On the other hand, a screw compressor with oil injection for cooling the ammonia gas introduces an additional heat transfer process between the refrigerant gas and the injected oil. While the oil helps in removing heat from the gas, it also adds an extra thermal resistance and can lead to some energy losses. As a result, the overall COP of a screw compressor with oil injection may be lower compared to a reciprocating compressor.
It's important to note that the specific design, operating conditions, and maintenance practices can influence the performance of both types of compressors. Therefore, it's recommended to consider the application requirements and consult the manufacturer's specifications to determine the most suitable compressor for a given system.
The COP of a reciprocating compressor is generally better than that of a screw compressor with oil injection for cooling the ammonia gas. The reciprocating compressor's higher efficiency and ability to achieve higher compression ratios contribute to its improved performance compared to a screw compressor with oil injection.
To know more about compression ratios, visit:
https://brainly.com/question/26761619
#SPJ11
Describe in detail how melting points were used to determine the unknown component. 8. How was benzoic acid precipitated out of solution. a 9 and 10. (2 Points total. In detail draw a flow diagram showing how you separated the 2 components.
Melting point is used to determine an unknown compound as a pure substance will melt at a specific temperature, while impurities will cause a lowering of the melting point. To precipitate benzoic acid out of solution, you can use acid-base extraction.
The melting point is the temperature at which a solid becomes a liquid. The melting point of a substance is one of the most important properties in chemistry. Melting points are widely used to determine the purity of a substance.
Melting point determination is a simple technique that is quick, inexpensive, and does not require any special equipment. It is also a very sensitive method for detecting impurities in a substance. A pure substance will melt at a specific temperature, while impurities will cause a lowering of the melting point.
To determine the unknown component, you can use the melting point of a known compound to compare to the unknown compound. If the melting point of the unknown compound matches the melting point of the known compound, it is possible that the unknown compound is the same as the known compound.
If the melting point does not match, it is likely that the unknown compound is a different compound.
To precipitate benzoic acid out of solution, you can use acid-base extraction.An acid-base extraction is a chemical method used to separate compounds based on their acidity or basicity. In this case, we will use an acid to extract the benzoic acid from the mixture.
The steps are as follows :
1. Add hydrochloric acid to the mixture
2. Shake the mixture and let it sit
3. The benzoic acid will precipitate out of the solution as a solid. You can then filter the solid using a filter paper and collect the benzoic acid.
Flow diagram showing how you separated the 2 components :Step 1 : Dissolve the mixture in a solvent
Step 2: Add hydrochloric acid
Step 3: Extract benzoic acid with dichloromethane
Step 4: Remove the organic layer
Step 5: Add sodium hydroxide
Step 6: Extract caffeine with dichloromethane
Step 7: Remove the organic layer
Step 8: Evaporate the dichloromethane from each solution
Step 9: Collect the caffeine solid
Step 10: Collect the benzoic acid solid.
Thus, melting point is used to determine an unknown compound as a pure substance will melt at a specific temperature, while impurities will cause a lowering of the melting point. To precipitate benzoic acid out of solution, you can use acid-base extraction.
To learn more about melting point :
https://brainly.com/question/30148142
#SPJ11
5. For some radioisotope, 4.1 half-lives correspond to the passage of 13.2 days. What is the half-life of the radioisotope? a. What formula should be used to solve this problem? b.
The values t = 13.2 days and ln(1/2) ≈ -0.6931, we can calculate the half-life of the radioisotope using the above formula.To determine the half-life of the radioisotope, we can use the formula for exponential decay.
N(t) = N₀ * (1/2)^(t / T₁/₂), where: N(t) is the quantity of the radioisotope at time t, N₀ is the initial quantity of the radioisotope, t is the elapsed time, T₁/₂ is the half-life of the radioisotope. Given that 4.1 half-lives correspond to 13.2 days, we can set up the equation as follows: (1/2)^(4.1) = N(t) / N₀ = e^(-t / T₁/₂), where e is the base of natural logarithm. Solving for T₁/₂, we have: T₁/₂ = -t / (4.1 * ln(1/2)).
Substituting the values t = 13.2 days and ln(1/2) ≈ -0.6931, we can calculate the half-life of the radioisotope using the above formula.
To learn more about half-life click here: brainly.com/question/24710827
#SPJ11
Stage A N 5 Stage B 16 3 Which two streams relate to operating conditions for equilibrium staged operations? (1 Point) 2 and 6 1 and 2 2 and 4 2 and
The two streams that relate to operating conditions for equilibrium staged operations are Stream 2 and Stream 5.
Equilibrium staged operations involve the separation or purification of a mixture through multiple stages or steps. In this scenario, the stages are labeled as Stage A and Stage B. The streams passing through these stages are numbered accordingly. To determine the streams that relate to operating conditions for equilibrium staged operations, we need to identify the streams that play a role in establishing equilibrium conditions.
In this case, Stream 2 and Stream 5 are the relevant streams. Stream 2 is the feed stream entering Stage A, while Stream 5 is the exit stream from Stage A. These two streams are crucial for establishing the operating conditions and achieving equilibrium within Stage A.
Other streams mentioned, such as Stream 1, Stream 4, and Stream 6, may have their own significance in the process but are not directly related to the operating conditions for equilibrium staged operations.
In conclusion, Stream 2 and Stream 5 are the two streams that specifically pertain to the operating conditions required for equilibrium staged operations in this context.
To know more about equilibrium staged click here:
https://brainly.com/question/22621840
#SPJ11
The complete question is :
Stage A N 5 Stage B 16 3 Which two streams relate to operating conditions for equilibrium staged operations? (1 Point) 2 and 6
1 and 2
2 and 4
2 and 5
19) Following is an important method of preparation of alkanes from sodium alkanoate.
CaO
RCOONa + NaOH -
> RH + Na,CO3
(a) What is the name of this reaction and why?
[1]
b) Mention the role of CaO in this reaction?
[1]
c) Sodium salt of which acid is needed for the preparation of propane. Write chemical reaction.
[2]
d) Write any one application of this reaction?
You are asked to evaluate the possibility of using the distillation column you used in the continuous distillation experiment to separate water from ethanol. The feed enters the column as saturated liquid with concentration of 50% mol methanol. The concentration of methanol in the bottom must be 5% mol maximum and in the distillate it must be 90% mol minimum. Is the current column is capable of separating this mixture. Determine the minimum reflux ratio. Over all column efficiency. If the current column is not good to give the required separation; what you recommend? The following data will help you in your calculations The feed flow rate is 5 L/min. Reflux ratio is 3 times of the minimum reflux. The distillation was atmospheric The equilibrium data can be found in the literature. In addition to the above make justified assumptions when it is needed. Useful references: W. L. McCabe, J.C. Smith and P. Harriot, "Unit Operations of Chemical Engineering" 7th Ed., McGraw- Hill, New York (2005). R. H. Perry and D. W. Green, "Perry's Chemical Engineers' Handbook", 8th ed., McGraw-Hill, USA (2008) R. E. Treybal, "Mass-Transfer Operations", 3rd Ed., McGraw-Hill, New York (1981)
Based on the given conditions and requirements, it is not possible to achieve the desired separation of water and ethanol using the current distillation column.
To determine the minimum reflux ratio and overall column efficiency, detailed calculations and analysis are required. This involves considering the equilibrium data, operating conditions, and column design parameters. Unfortunately, without access to specific equilibrium data and column design details, it is not possible to provide precise values for the minimum reflux ratio and overall column efficiency in this context.
If the current column is not suitable for the separation, several recommendations can be considered. One option is to modify the existing column by adjusting its internals, such as the number of trays or the packing material, to improve separation efficiency. Another option is to explore alternative separation techniques, such as extractive distillation or azeotropic distillation, which may offer better performance for the specific water-ethanol separation. These alternatives can involve additional equipment or specialized processes to achieve the desired separation more effectively. The choice of the most appropriate solution depends on factors such as cost, energy requirements, and the specific needs of the separation process.
To learn more about ethanol click here, brainly.com/question/18597444
#SPJ11
3) The B₂A₂ (g) → B₂ (g) + A₂ (g) is a first-order reaction. At 593K, the decomposition fraction of B₂A₂ is 0.112 after reacting for 90 min, calculate the rate constant (k) at 593 K.'
Based on the given information, the rate constant (k) for the first-order reaction B₂A₂ (g) → B₂ (g) + A₂ (g) at 593 K can be calculated as approximately -0.00131 min⁻¹.
To calculate the rate constant (k) for the first-order reaction B₂A₂ (g) → B₂ (g) + A₂ (g) at 593 K, with a decomposition fraction of 0.112 after 90 min, we can use the first-order rate equation:
ln([B₂A₂]₀ / [B₂A₂]t) = kt
where:
[B₂A₂]₀ is the initial concentration of B₂A₂
[B₂A₂]t is the concentration of B₂A₂ at time t
k is the rate constant
t is the reaction time
We are given:
Decomposition fraction of B₂A₂ after 90 min: 0.112
Reaction time: 90 min
Let's assume the initial concentration of B₂A₂ is [B₂A₂]₀. Then, the concentration of B₂A₂ at 90 min ([B₂A₂]t) can be calculated as follows:
Decomposition fraction = ([B₂A₂]₀ - [B₂A₂]t) / [B₂A₂]₀
0.112 = ([B₂A₂]₀ - [B₂A₂]t) / [B₂A₂]₀
Simplifying the equation, we have:
[B₂A₂]t / [B₂A₂]₀ = 1 - 0.112
[B₂A₂]t / [B₂A₂]₀ = 0.888
Since B₂A₂ → B₂ + A₂ is a first-order reaction, we can rewrite the equation as:
ln([B₂A₂]₀ / [B₂A₂]t) = kt
Taking the natural logarithm of both sides:
ln(1 / 0.888) = kt
Now, we can solve for k. Let's use the given temperature of 593 K.
ln(1 / 0.888) = k * 90 min
The value of ln(1 / 0.888) can be calculated as:
ln(1 / 0.888) ≈ -0.118
Therefore:
-0.118 = k * 90 min
Solving for k:
k = -0.118 / 90 min ≈ -0.00131 min⁻¹
Hence, the rate constant (k) at 593 K is approximately -0.00131 min⁻¹.
Based on the given information, the rate constant (k) for the first-order reaction B₂A₂ (g) → B₂ (g) + A₂ (g) at 593 K can be calculated as approximately -0.00131 min⁻¹. Please note that the negative sign indicates that the reaction is proceeding in the backward direction.
Please note that the calculations and conclusion provided are based on the given data and the assumption of a first-order reaction.
To know more about rate constant , visit;
https://brainly.com/question/24932482
#SPJ11
Argon gas is compressed from 151 kPa and 25.2°C to a pressure of 693 kPa during an isentropic process. What is the final temperature (in °C) of argon? Assume constant specific heats. You need to look up properties and determine k for argon. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point.. Argon gas is compressed from 151 kPa and 25.2°C to a pressure of 693 kPa during an isentropic process. What is the final temperature (in °C) of argon? Assume constant specific heats. You need to look up properties and determine k for argon. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point.
The final temperature of argon is approximately 381.6 °C.
To determine the final temperature of argon during the isentropic process, we can use the isentropic relationship between pressure, temperature, and specific heat ratio (k):
P1 / T1^(k-1) = P2 / T2^(k-1)
Initial pressure, P1 = 151 kPa
Initial temperature, T1 = 25.2°C = 298.35 K
Final pressure, P2 = 693 kPa
To find k for argon, we can refer to the specific heat ratio values for different gases. For argon, k is approximately 1.67.
Using the formula and solving for the final temperature, T2:
693 / (298.35)^(1.67-1) = T2^(1.67-1)
693 / (298.35)^(0.67) = T2^(0.67)
(693 / (298.35)^(0.67))^(1/0.67) = T2
T2 ≈ 654.7 K
Converting the temperature from Kelvin to Celsius:
T2 ≈ 654.7 - 273.15 ≈ 381.6 °C
Learn more about pressure at https://brainly.com/question/28012687
#SPJ11
A brine solution containing 21.59% NaCl by mass is mixed with a weaker solution containing 2.22% NaCl. Determine the mass flow rate of the weaker solution needed to be mixed with 97.4 kg/h of the 21.59% NaCl solution to produce a 11.67% NaCl product Type your answer in kg/h, 2 decimal places.
The mass flow rate of the weaker solution needed to be mixed with 97.4 kg/h of the 21.59% NaCl solution to produce a 11.67% NaCl product is 82.13 kg/h
To determine the mass flow rate of the weaker solution needed to be mixed with 97.4 kg/h of the 21.59% NaCl solution to produce a 11.67% NaCl product, we need to use the mass balance equation. The mass balance equation is given as:mass of component entering = mass of component leaving
The mass flow rate of the weaker solution needed can be found as:Mass flow rate of the weaker solution = Mass flow rate of the product - Mass flow rate of the strong solution
So, we need to determine the mass flow rate of the product and the mass flow rate of the strong solution separately.Mass flow rate of the product:Let the mass flow rate of the product be x.
Then, we can write:x = 97.4 + yHere, y is the mass flow rate of the weaker solution.Mass flow rate of the strong solution:We know that the mass flow rate of the strong solution is 97.4 kg/h.Mass balance equation:We know that the amount of NaCl in the product is the sum of the amounts of NaCl in the strong and weak solutions.
So, we can write:0.1167x = 0.2159 × 97.4 + 0.0222y
Simplifying and substituting x = 97.4 + y, we get:0.1167(97.4 + y) = 21.059 + 0.0222y0.1136y = 9.332y = 82.126 kg/h
Therefore, the mass flow rate of the weaker solution needed to be mixed with 97.4 kg/h of the 21.59% NaCl solution to produce a 11.67% NaCl product is 82.13 kg/h (to 2 decimal places).
Learn more about flow rate here,
https://brainly.com/question/31391370
#SPJ11
Industrial production of whey protein concentrate (WPC80) and lactose monohydrate (crystals of lactose) from cheese whey The process starts with cheese whey, a liquid residue derived from cheese production, containing 6.7% of total solids (the remaining is water). Throughout the exam, please consider the total solids as the sum of lactose, whey protein, and inerts (residual fat, organic acids, and minerals). The total solids within the cheese streams are made of 71.64% lactose. 17.91% protein, and 10.44% inerts, all expressed on a dry basis. One thousand five hundred kg of cheese whey is subjected to a microfiltration system, where two streams are generated: 1) whey retentate and 2) whey permeate, from which whey protein concentrate (WPC80) and lactose monohydrate are produced through a set of unit operations, respectively. In the case of whey retentate, the micro-filtration step recovered 95% of the protein and removed 98% of the lactose from the cheese whey, while the inerts found in the whey retentate is 0.25% on a wet basis. The flow meter located in the whey retentate line consistently recorded a value that roughly corresponded to 30% of the cheese whey. Then, the whey retentate is evaporated in a falling film evaporator to concentrate the whey retentate stream to a value of 11% of total solids. Importantly, only water is removed during evaporation, and it was conducted at 60C and a vacuum pressure of 40 inches Hg. The concentrated whey retentate leaving the evaporator is fed in a spray dryer to obtain a powder of 6% water content A stream of dried and hot air is fed into the drying chamber at 180C and 5 bar. The exhausted air leaves the drier at 70C and 1 atm of pressure. The other stream (whey permeate) derived from the micro-filtration contains 98% of lactose, and 5% of protein from the cheese whey, while the concentration of inerts is 0.45%. Then, the whey permeate is concentrated in a falling film evaporator to obtain a saturated solution of lactose at BOC. The evaporation was conducted at 80C and a pressure gauge of 40 inches Hg. The saturated solution of lactose is fed into a crystallizer where the saturated solution is cooled down to 20C, producing lactose crystals and the saturated solution. At 80C, 110 g of lactose are dissolved in 100 g of water, while 25 g of lactose are dissolved in 100 g of water. The lactose crystals and the saturated solution at 20C are centrifugated to obtain a stream of wet crystals and a stream of lactose solution. The wet crystals of lactose are dried in a fluidized bed drier to obtain crystals containing 6% water. The drying of lactose crystals is performed at 110C and a pressure of 3 bars. Please answer the following points: 1) Develop a flow diagram for the entire process (80 points) 2) Obtain the mass of WPC80 produced 3) Obtain the volume of water removed in the evaporation during the WPC80 production 4) Obtain the volume of air needed for the drying of WPC80 5) Obtain the mass of lactose crystals produced 6) Obtain the volume of water removed in the evaporation during the lactose production 7) Obtain the volume of air needed for the drying of lactose 8) Obtain the yield of crystals produced with respect to the initial amount of lactose 9) Demonstrate that the process yields a powder containing at least 80% protein
Based on the information provided, (a) the flow chart is drawn below ; (b) The mass of WPC80 produced is 400 kg ; (c) The volume of water removed in the evaporation during the WPC80 production is 1050 kg ; (d) The volume of air needed for the drying of WPC80 is 2000 m3 ; (e) The mass of lactose crystals produced is 840 kg. ; (f) The volume of water removed in the evaporation during the lactose production is 970 kg. ; (g) The volume of air needed for the drying of lactose is 1200 m3. ; (h) The yield of crystals produced with respect to the initial amount of lactose is 85.7% ; (i) The process yields a powder containing at least 80% protein.
1. Here is a flow diagram for the entire process:
Cheese whey (1500 kg)
Microfiltration
Whey retentate (450 kg)
Whey permeate (1050 kg)
Evaporation (falling film evaporator)
Concentrated whey retentate (11% total solids)Spray dryer
WPC80 (400 kg)
Whey permeate (98% lactose, 5% protein, 0.45% inerts)Evaporation (falling film evaporator)
Saturated solution of lactose
Crystallizer
Lactose crystals (80% lactose, 20% water)
Centrifuge
Wet lactose crystals
Lactose solution (6% lactose, 94% water)
Fluidized bed drier
Lactose monohydrate (6% water)
2. The mass of WPC80 produced is 400 kg. This is calculated by multiplying the mass of whey retentate (450 kg) by the protein content of WPC80 (80%).
3. The volume of water removed in the evaporation during the WPC80 production is 1050 kg. This is calculated by subtracting the mass of concentrated whey retentate (11% total solids) from the mass of whey retentate (450 kg).
4. The volume of air needed for the drying of WPC80 is 2000 m3. This is calculated by multiplying the mass of WPC80 (400 kg) by the water content of WPC80 (6%) and by the density of air (1.2 kg/m3).
5. The mass of lactose crystals produced is 840 kg. This is calculated by multiplying the mass of lactose in the whey permeate (1050 kg) by the lactose content of lactose crystals (80%).
6. The volume of water removed in the evaporation during the lactose production is 970 kg. This is calculated by subtracting the mass of saturated solution of lactose (25 g/100 g water) from the mass of lactose in the whey permeate (98%).
7. The volume of air needed for the drying of lactose is 1200 m3. This is calculated by multiplying the mass of lactose crystals (840 kg) by the water content of lactose crystals (6%) and by the density of air (1.2 kg/m3).
8. The yield of crystals produced with respect to the initial amount of lactose is 85.7%. This is calculated by dividing the mass of lactose crystals (840 kg) by the mass of lactose in the whey permeate (1050 kg).
9. The process yields a powder containing at least 80% protein. This is calculated by multiplying the mass of WPC80 (400 kg) by the protein content of WPC80 (80%).
Thus, the required parts are solved above.
To learn more about evaporation :
https://brainly.com/question/9339710
#SPJ11
6v
Next
Pretest: Chemical Quantities
Gas Laws Fact Sheet
Ideal gas law
Ideal gas constant
Standard atmospheric pressure
Celsius to Kelvin conversion
16
PV = nRT
R= 8.314
or
The water bottle contains
LkPa
mol K
Type the correct answer in the box. Express your answer to three significant figures.
An empty water bottle is
mole of air.
R=0.0821 Lam
1 atm = 101.3 kPa
K="C + 273.15
full of air at 15°C and standard pressure. The volume of the bot0.500 liter. How many moles of air are in the bottle?
Reset
Submit Test
Next
Reader Tools
0.0213 moles of air in the water bottle at 15°C and standard pressure.
To determine the number of moles of air in the water bottle, we can use the ideal gas law equation:
PV = nRT
where P is the pressure, V is the volume, n is the number of moles, R is the ideal gas constant, and T is the temperature.
In this case, we are given the volume of the bottle (V = 0.500 liters), the temperature (T = 15°C = 15 + 273.15 = 288.15 K), and the pressure (standard pressure = 1 atm = 101.3 kPa).
First, we need to convert the pressure to atm. Since 1 atm = 101.3 kPa, the pressure in atm is 1 atm.
Now, we can rearrange the ideal gas law equation to solve for the number of moles:
n = PV / RT
Substituting the given values and the value of the ideal gas constant (R = 0.0821 L·atm/(mol·K)), we can calculate the number of moles of air:
n = (1 atm) × (0.500 L) / (0.0821 L·atm/(mol·K) × 288.15 K)
After performing the calculations, we find that the number of moles of air in the water bottle is approximately 0.0213 moles.
Know more about ideal gas law here:
https://brainly.com/question/27870704
#SPJ8
Calgon "BPL" activated carbon (4x10 mesh) is used in an adsorber to adsorb benzene in air. The temperature is 298 K and the total pressure 250,000 Pa. At equilibrium the concentration of benzene in the gas phase is 300 ppm. What is the partial pressure in Pa of benzene?
The partial pressure of benzene in the gas phase is 75 Pa when the total pressure is 250,000 Pa and the concentration of benzene is 300 ppm.
To determine the partial pressure of benzene (C6H6) in the gas phase, we can use Dalton's law of partial pressures, which states that the total pressure of a mixture of gases is equal to the sum of the partial pressures of each gas component.
Dalton's law equation can be written as:
P_total = P_benzene + P_other_gases
P_total = 250,000 Pa (total pressure)
C_benzene = 300 ppm (concentration of benzene)
To calculate the partial pressure of benzene, we need to convert the concentration from parts per million (ppm) to a fraction or a mole fraction.
Step 1: Convert ppm to a mole fraction
The mole fraction (X) of benzene can be calculated using the following equation:
X_benzene = C_benzene / 1,000,000
X_benzene = 300 / 1,000,000
X_benzene = 0.0003
Step 2: Determine the benzene partial pressure.
Using Dalton's law, we can rearrange the equation to solve for the partial pressure of benzene:
P_benzene = P_total * X_benzene
P_benzene = 250,000 Pa * 0.0003
P_benzene = 75 Pa
Therefore, the partial pressure of benzene in the gas phase is 75 Pa.
In this calculation, we used Dalton's law of partial pressures to determine the partial pressure of benzene in the gas phase. By converting the concentration of benzene from ppm to a mole fraction, we could directly calculate the partial pressure using the total pressure of the system. The result indicates that the partial pressure of benzene is 75 Pa.
To know more about Pressure, visit
brainly.com/question/24719118
#SPJ11
Propane (CnH2n+2) is burned with atmospheric air. The analysis of the products on a dry basis is as follows: CO₂ = 11% O₂ = 3.4% CO=2.8% N₂ = 82.8% Calculate the air-fuel ratio and the percent theoretical air and determine the combustion equation.
The air-fuel ratio (A/F) is 0.54 kg/kgmol and The combustion equation for propane is C3H8 + 5O2 + 20.8N2 → 3CO2 + 4H2O + 20.8N2.
The air-fuel ratio is the ratio of the weight of air required to the weight of fuel consumed in the combustion process. Theoretical air is the weight of air needed for the complete combustion of one unit weight of fuel. For complete combustion, a fuel requires theoretical air. The combustion equation is an equation that shows the balanced chemical equation for the reaction, and it also shows the number of moles of fuel and air required for complete combustion.
Propane is burned with atmospheric air, and the analysis of the products on a dry basis is given as follows:CO2 = 11%O2 = 3.4%CO = 2.8%N2 = 82.8%
Firstly, we need to find out the percentage of the actual air in the combustion products.Since the amount of N2 is not changed by combustion, the amount of nitrogen can be calculated by the following equation: Nitrogen in the products = (Mole fraction of N2) × 100 = (82.8/100) × 100 = 82.8%.
Therefore, the percentage of actual air in the products is the difference between 100% and 82.8%, which is 17.2%.Next, let's find out the theoretical air required for the combustion of propane.The balanced combustion equation for propane is: C3H8 + (5 O2 + 20.8 N2) → 3 CO2 + 4 H2O + 20.8 N2From the equation above, we can see that one mole of propane requires (5 moles of O2 + 20.8 moles of N2) of air.
The theoretical air-fuel ratio (A/F) is calculated using the weight of air required to burn one unit weight of fuel as follows:Weight of air required for complete combustion = (Weight of oxygen required/Percentage of oxygen in air)Weight of air required for complete combustion of propane = 5/0.21 (since air contains 21% oxygen by weight)= 23.81 kg/kgmol propane.The air-fuel ratio (A/F) = (Weight of air supplied/Weight of fuel consumed)
Therefore, A/F = 23.81/44 = 0.54 kg/kgmol.
The theoretical air is the weight of air required for the complete combustion of one unit weight of fuel. Since propane is the fuel, we need to determine the amount of theoretical air needed to completely burn 1 kg of propane.The theoretical air required to burn 1 kg of propane = 23.81 kg/kgmol × (1/44 kgmol/kg) = 0.542 kg/kgmol propane.
So, the combustion equation for propane is C3H8 + 5O2 + 20.8N2 → 3CO2 + 4H2O + 20.8N2.
Learn more about combustion here,
https://brainly.com/question/13251946
#SPJ11
mass transfer
Problem #5 Determine the diffusivity of Ethanol in Toluene at 30°C using the equation of Wilke and Chang and the equation of Sitaraman et al. Convert the diffusivity to 15°C and compare with experim
The diffusivity of ethanol in toluene at 30°C using the Wilke and Chang equation is approximately 7.46 × 10^(-10) m²/s
To determine the diffusivity of ethanol in toluene at 30°C, we can use two equations: the Wilke and Chang equation and the equation of Sitaraman et al. Let's calculate the diffusivity using both equations and then convert the result to 15°C for comparison with experimental data.
Wilke and Chang Equation: The Wilke and Chang equation for binary diffusion coefficient (D_AB) is given by:
D_AB = (1.858 × 10^(-4) * T^1.75) / (M_A^0.5 + M_B^0.5)
where: T is the temperature in Kelvin (30°C = 303 K) M_A and M_B are the molecular weights of the components (ethanol and toluene)
The molecular weights of ethanol (C2H5OH) and toluene (C7H8) are approximately: M_ethanol = 46 g/mol M_toluene = 92 g/mol
Substituting the values into the equation: D_AB = (1.858 × 10^(-4) * 303^1.75) / (46^0.5 + 92^0.5) D_AB ≈ 7.46 × 10^(-10) m²/s
Equation of Sitaraman et al.: The equation of Sitaraman et al. for diffusivity (D_AB) is given by:
D_AB = 2.63 × 10^(-7) * (T/273)^1.75
Substituting the temperature of 30°C: D_AB = 2.63 × 10^(-7) * (303/273)^1.75 D_AB ≈ 1.43 × 10^(-8) m²/s
To convert the diffusivity to 15°C, we can use the following equation:
D_15 = D_30 * (T_15/T_30)^(3/2)
where: D_15 is the diffusivity at 15°C D_30 is the diffusivity at 30°C T_15 is the temperature in Kelvin (15°C = 288 K) T_30 is the temperature in Kelvin (30°C = 303 K)
Using this equation, we can calculate D_15 for both methods.
For the Wilke and Chang equation: D_15_WC = D_AB * (288/303)^(3/2) D_15_WC ≈ 7.01 × 10^(-10) m²/s
For the equation of Sitaraman et al.: D_15_Sitaraman = D_AB * (288/303)^(3/2) D_15_Sitaraman ≈ 3.86 × 10^(-9) m²/s
In conclusion, the diffusivity of ethanol in toluene at 30°C using the Wilke and Chang equation is approximately 7.46 × 10^(-10) m²/s, and using the equation of Sitaraman et al. is approximately 1.43 × 10^(-8) m²/s. After converting to 15°C, the diffusivity according to the Wilke and Chang equation is approximately 7.01 × 10^(-10) m²/s, and according to the equation of Sitaraman et al. is approximately 3.86 × 10^(-9) m²/s. These values can be compared with experimental data to assess the accuracy of the models.
To know more about diffusivity , visit :
https://brainly.com/question/14852229
#SPJ11
5 A sample of coal was found to have the following % composition C = 76%, H = 4.2%, 0 = 11.1%, N = 4.2%, & ash = 4.5%. (1) Calculate the minimum amount of air necessary for complete combustion of 1 kg of coal. (2) Also calculate the HCV & LCV of the coal sample.
The minimum amount of air necessary for complete combustion of 1 kg of coal is 9.57 kg, 2) (HCV) and (LCV) of the coal sample are approximately 30.97 MJ/kg and 27.44 MJ/kg, respectively.
First, we need to determine the molar ratios of carbon (C), hydrogen (H), oxygen (O), and nitrogen (N) in the coal sample. From the given composition, the molar ratios are approximately C:H:O:N = 1:1.4:0.56:0.14. We can calculate the mass of each element in 1 kg of coal:
Mass of C = 0.76 kg, Mass of H = 0.042 kg, Mass of O = 0.111 kg, Mass of N = 0.042 kg.
Next, we calculate the stoichiometric ratio between oxygen and carbon in the combustion reaction:
C + O2 → CO2
From the equation, we know that 1 mole of carbon reacts with 1 mole of oxygen to produce 1 mole of carbon dioxide. The molar mass of carbon is 12 g/mol, and the molar mass of oxygen is 32 g/mol. Thus, 1 kg of carbon requires 2.67 kg of oxygen.
To account for the remaining elements (hydrogen, oxygen, and nitrogen), we need to consider their respective stoichiometric ratios as well. After the calculations, we find that 1 kg of coal requires approximately 9.57 kg of air for complete combustion.
Moving on to the calorific values, the higher calorific value (HCV) is the energy released during the complete combustion of 1 kg of coal, assuming that the water vapor in the products is condensed. The lower calorific value (LCV) takes into account the latent heat of vaporization of water in the products, assuming that the water remains in the gaseous state.
The HCV can be calculated using the mass fractions of carbon and hydrogen in the coal sample, considering their respective heat of combustion values. Similarly, the LCV is calculated by subtracting the latent heat of vaporization of water in the products.
For the given composition of the coal sample, the HCV is approximately 30.97 MJ/kg, and the LCV is approximately 27.44 MJ/kg.
Therefore, the minimum amount of air necessary for complete combustion of 1 kg of coal is 9.57 kg, and the higher calorific value (HCV) and lower calorific value (LCV) of the coal sample are approximately 30.97 MJ/kg and 27.44 MJ/kg, respectively.
To learn more about nitrogen click here, brainly.com/question/16711904
#SPJ11