Dilute countercurrent immiscible extraction
A feed of 100.0 kg/min of a 1.2 wt % mixture of acetic acid in water is to be extracted with 1-butanol at 1 atm pressure and 26.7°C, we desire an outlet concentration of 0.1 wt % acetic acid in the exiting water. We have available solvent stream 1 that is 44.0 kg/min of pure 1-butanol and solvent stream 2 that is 30.0 kg/min of 1-butanol that contains 0.4 wt % acetic acid. Devise a scheme to do this separation, find the outlet flow rate and concentration of the exiting 1-butanol phase, and find the number of equilibrium contacts needed.
In Example we assumed that we were going to use all of the solvent available. There are other alternatives. Determine if the following alternatives are capable of producing outlet water of the desired acetic acid concentration.
a. Use only the pure solvent at the bottom of the extractor.
b. Mix all of the pure and all of the impure solvent together and use them at the bottom of the column.
c. Mix all of the pure and part of the impure solvent together and use them at the bottom of the column.

Answer:

yes i do.

Explanation:

it's pretty easy in my opinion but i dont know about you why do you ask?

Answer:

Presents the relevant parameters to be kept in mind when using the following types of motors: 1. AC induction motor 2. BLDC motor 3. Synchronous motorn

Explanation:

sorry

Answer: Hepatitis A

Explanation:

nagdudulot ng pamamaga ng atay

Answer:

Objects that float on water have densities less than the density of water; those that do not float on water have densisties greater than the density of water:

Float on water:  d < 0.0361 lb/in³ (where d denotes denisity)

Do not float on water:  d > 0.0361 lb/in³

Explanation:

I don't know if this works for it or not?

Answer: 8.33333333 or 6.1989778

Explanation:

Answer:true

Explanation:

It is true that around 50 percent of all sales of farm commodities are from dairy products.

Dairy products or milk products, also known as lacticinia, are milk-based foods.

Cows, water buffalo, nanny goats, and ewes are the most common dairy animals. Dairy products include common grocery store foods such as yogurt, cheese, and butter in the Western world.

Milk, yogurt, cheese, lactose-free milk, and fortified soy milk and yogurt are all part of the Dairy Group. The Dairy Group excludes milk-based foods with low calcium and a high fat content. Cream cheese, sour cream, cream, and butter are all examples of this.

Dairy products account for roughly half of all farm commodity sales.

Thus, the given statement is true.

For more details regarding dairy products, visit:

https://brainly.com/question/1431669

#SPJ2

Answer:

not sure

Explanation:

not sure

The reason for low power factor in no load test in induction motor is high rotor reactance at lower loading since the rotor reactance value gets decreased with increased loading on induction motor

Usually at no load, the Cosine of the phase angle between the stator current(I1) and the stator applied voltage(V1) is the power factor of an induction motor.

In conclusion, the reason for low power factor in no load test in induction motor is high rotor reactance at lower loading since the rotor reactance value gets decreased with increased loading on induction motor

Read more about induction motor

brainly.com/question/1049516

Answer:

affects the flow of electricity

Explanation:

A loose battery terminal affects the flow of electricity. There is less power going to the electrical systems and the vehicle will not start or start sluggishly. Also, a loose battery terminal causes the car's electrical components like navigation, car lights, and audio among others to dim or fail completely.

The water surface elevation must be 110.2631 meters for a flow of 0.03m³ to occur in the cast pipe

For cast iron the chart has 0.0012  from Moody's chart

0.016 for cast iron

[tex]hf = \frac{flQ^{2}}{12.1d5}[/tex]

[tex]h1 = h2+\frac{Q^{2} }{12.1} [\frac{0.0012*100}{(12/1000)^5} +\frac{0.0016*150}{(15/100)^5} ][/tex]

[tex]h1 = 110m+\frac{0.03^2}{12.1} [\f\frac{0.12}{0.00032} +\frac{0.24}{0.000759} ]\\\\h1 = 110+0.0000744[375+3162.06]\\\\= 110 + 0.2631m\\\\= 110.2631m[/tex]

Therefore the water surface elevation must be 110.2631 meters for a flow of 0.03m³ to occur in the cast pipe

Read more on https://brainly.com/question/14081661?referrer=searchResults

Answer:

Four types of gas turbine engines are used to propel and power aircraft. They are the turbojet, turbofan, turboprop, and turboshaft.

Answer:

A gas turbine, also called a combustion turbine, is a type of continuous and internal combustion engine. The main elements common to all gas turbine engines are: ... Gas turbines are used to

Explanation:

Answer:

i dob't know

Explanation:

Answer:

Explanation:

Work, U, is equal to the force times the distance:

U = F · r

Force needed to lift the weight, is equal to the weight: F = W = m · g

so:

U = m · g · r

   = 20.4kg · 9.81 [tex]\frac{N}{kg}[/tex] · 1.50m

   = 35.316 [tex]\frac{N}{m}[/tex]

   = 35.316 W

Answer:

Use this PDF file it should help you calculate total photon flux incident on the photodiode.

Explanation:

It's a file on lecture notes that help people learn about engineering and maybe in the lecture notes it might have information about how to calculate total photon flux incident on the photodiode