Current I flows along the positive z-direction in the inner conductor of a long coaxial cable and returns through the outer conductor. The inner conductor has radius a, and the inner and outer radii of the outer conductor are b and c, respectively. (a) Determine the magnetic field in each of the following regions: 0 ≤ r ≤ a, a ≤ r ≤ b, b ≤ r ≤ c, and r ≥ c. (b) Plot the magnitude of H as a function of r over the range from r = 0 to r = 10 cm, given that I = 10 A, a = 2 cm, b = 4 cm, and c = 5 c
Answers
Answer:
A) determine magnetic fields
For 0 ≤ r ≤ a
Magnetic field = ∅ [tex]\frac{rI}{2\pi a^2}[/tex]
For a ≤ r ≤ b
Magnetic field = ∅ [tex]\frac{I}{2\pi r}[/tex]
For b ≤ r ≤ c
Magnetic field in the region = ∅ [tex]\frac{I}{2\pi r} [ c^2 - r^2 / c^2-b^2 ][/tex]
For r ≥ c
magnetic filed in the region = 0
B ) attached below
Explanation:
A) Determine the magnetic field in the following regions
i) For 0 ≤ r ≤ a
Magnetic field = ∅ [tex]\frac{rI}{2\pi a^2}[/tex]
attached below is the detailed solution
ii) For a ≤ r ≤ b
Magnetic field = ∅ [tex]\frac{I}{2\pi r}[/tex]
attached below is the detailed solution
iii) For b ≤ r ≤ c
Magnetic field in the region = ∅ [tex]\frac{I}{2\pi r} [ c^2 - r^2 / c^2-b^2 ][/tex]
attached below is the detailed solution
iv) For r ≥ c
magnetic filed in the region = 0 and this is because the net current enclosed in the region = 0
Related Questions
When the electrons reach the collector, they flow towards the positivly charged grid. The resulting current is measured. Note that as the electrons accelerate from the cathode toward the grid, they collide with the mercury atoms. Assume that these collisions are completely elastic. How does the collected current vary if the ΔVgrid is slowly increased? View Available Hint(s) When the electrons reach the collector, they flow towards the positivly charged grid. The resulting current is measured. Note that as the electrons accelerate from the cathode toward the grid, they collide with the mercury atoms. Assume that these collisions are completely elastic. How does the collected current vary if the is slowly increased? The current increases. The current remains constant. The current decreases.
Answers
Answer:
the current INCREASES.
Explanation:
In this experiment, the electrons are generated by a filament with very low speed, when they are subjected to a difference and potential ΔV they acquire the necessary speed to reach the regulation and the current can be measured.
Some electrons collide elastically with the atoms of the mercury gas that is much heavier and are scattered in any direction, so they do not reach the grid, by increasing the voltage this scattered electrons can acquire the necessary speed in the direction of grid to reach it and therefore are also measured, increasing the current.
Therefore, as the power difference increases, the current INCREASES.
A power plant burns coal to generate electricity. Suppose that 1000 J of heat (Q) from the coal fire enters a boiler, which is kept at a constant temperature of 900 C. That 1000 J is used to boil water in a boiler. The steam from the boiler is used to drive a turbine that creates electricity (work). The excess heat is put into a cooling tower at 5 C.
Carnot efficiency If everything is perfectly efficient,
• What is the maximum efficiency that the plant could operate at?
• How much work could be done starting from that 1000 J?
Answers
Answer:
The work done will be "763 J". A further explanation is given below.
Explanation:
The given values are:
[tex]Q_1=1000 \ J[/tex]
Temperature,
[tex]T_1=900^{\circ} C[/tex]
i.e,
[tex]=1173[/tex]
[tex]T_2=5^{\circ}C[/tex]
i.e.,
[tex]=278[/tex]
As we know,
⇒ [tex]\eta =1-\frac{T_2}{T_1}[/tex]
On substituting the values, we get
⇒ [tex]=1-\frac{278}{1173}[/tex]
⇒ [tex]=\frac{1173-278}{1173}[/tex]
⇒ [tex]=\frac{895}{1173}[/tex]
⇒ [tex]=0.763[/tex]
then,
⇒ [tex]W=\eta Q_1[/tex]
⇒ [tex]=0.763\times 1000[/tex]
⇒ [tex]=763 \ J[/tex]
what is the wavelength of a wave with the frequency of 330 Hz and a speed of 343 m/s
Answers
Answer:
The wavelength of a wave with the frequency of 330hz and a speed of 343m/s would be 1.04m
Explanation:
You can get the wavelength of a wave by dividing the speed of the wave by its frequency, which in this case would be:
343/300, which as a decimal number, it'd be 1.04.
I hope I helped you, and a "Brainliest" is always appreciated! ☺
3. Two spherical objects have masses of 4.7 x 105 kg and 7.9 x 103 kg. The
gravitational attraction between them is 68 N. How far apart are their
centers?
Answers
Answer:
0.06
Explanation:
Working on the problem at hand i calculated and got my answer to around simplified at 0.06
What is the wavelength associated with an electron with a velocity of 4.8x10*5 m/s?
(mass of the electron is 9.1 X 10-*31kg)
Answers
Answer:
Explanation:
Given the following data;
Mass = 9.1 X 10^{-31} kg
Velocity = 4.8x10⁵ m/s
Planck’s constant ( h ) = 6.6262 * 10^{-34}
To find the wavelength;
Applying de broglie's equation;
Wavelength = h/mv
Wavelength = ) = 6.6262 * 10^{-34}/(9.1 X 10^{-31} * 4.8x10⁵)
Wavelength = 1.52 * 10^{-71} meters
System A consists of a mass m attached to a spring with a force constant k; system B has a mass 2m attached to a spring with a force constant k; system C has a mass 3m attached to a spring with a force constant 6k; and system D has a mass m attached to a spring with a force constant 4k.
Rank these systems in order of increasing period of oscillation. (Use only the symbols < and =, for example A < B = C.)
Answers
Solution :
We know that the time period of oscillation of a spring mass system is given by :
[tex]$T = 2 \pi \sqrt{\frac{m}{k}}$[/tex] , where m is mass and k is the spring constant
∴ [tex]$T_A = 2 \pi \sqrt{\frac{m}{k}}$[/tex] .........(i)
[tex]$T_B = 2 \pi \sqrt{\frac{2m}{k}}$[/tex] ..........(ii)
[tex]$T_C = 2 \pi \sqrt{\frac{3m}{6k}} = 2 \pi \sqrt{\frac{m}{2k}}$[/tex] ..........(iii)
[tex]$T_D = 2 \pi \sqrt{\frac{m}{4k}}$[/tex] ...............(iv)
Comparing the equations (i), (ii), (iii) and (iv)
We get
[tex]$T_B > T_A > T_C > T_D$[/tex]
So in increasing order of time period, we get
[tex]$T_D < T_C < T_A < T_B$[/tex]
Number 29 plz help physics
Answers
Answer:
a. E = 900000 J = 900 KJ
b. ΔT = 8.18 °C
c. Cost = $ 7.2
Explanation:
a.
The energy can be given by:
[tex]E = Pt[/tex]
where,
E = Energy = ?
P = Power = 500 W
t = time = (0.5 h)(3600 s/1 h) = 1800 s
Therefore,
[tex]E = (500\ W)(1800\ s)[/tex]
E = 900000 J = 900 KJ
b.
The change in temperature of room air is given by the following formula:
[tex]0.5E = mC\Delta T\\[/tex] (since 50% of energy is used to heat air)
where,
m = mass of air = 50 kg
C = specific heat of air = 1.1 KJ/kg.°C
ΔT = Change in temperature of air = ?
Therefore,
[tex](0.5)(900\ KJ) = (50\ kg)(1.1\ KJ/Kg.^oC)\Delta T[/tex]
ΔT = 8.18 °C
c.
First, we will calculate the total energy consumed:
[tex]E = (0.5\ KW)(6\ h/d)(30\ d)\\E = 90\ KWh[/tex]
Now, for the cost:
[tex]Cost = (Unit\ Cost)(Energy)\\Cost = (\$ 0.08\KWh)(90\ KWh)[/tex]
Cost = $ 7.2
un cubo de aluminio tiene un volumen de 45cm3 cuál es su masa en gramos
Answers
The energy of motion is called...?
Answers
Which of the following is an example of a healthy behavior?
OA
Binge drinking of alcohol
OB.
Smoking cigarettes
OC.
Driving a car recklessly
OD.
None of the above
PE Not Physics
Answers
Answer moderate alcohol can be good for you health
Explanation: but I wouldn't do none of those things to be honest
SMARTEST
Answer:
none of the above
Explanation:
its an easy question haha
A ball with a mass of 0.585 kg is initially at rest. It is struck by a second ball having a mass of 0.420 kg , initially moving with a velocity of 0.270 m/s toward the right along the x axis. After the collision, the 0.420 kg ball has a velocity of 0.220 m/s at an angle of 36.9 ∘ above the x axis in the first quadrant. Both balls move on a frictionless, horizontal surface.
Required:
a. What is the magnitude of the velocity of the 0.605kg ball after the collision?
b. What is the direction of the velocity of the 0.605kg ball after the collision?
c. What is the change in the total kinetic energy of the two balls as a result of the collision?
Answers
Answer:
a) [tex](v_1)=0.3989m/s[/tex]
b) [tex]\theta_1=80.5 \textdegree[/tex]
c) [tex]K.E=0.036J[/tex]
Explanation:
From the question we are told that:
Initial speed of 1st ball [tex]u_{1}=0 m/s[/tex]
Mass of 1st ball [tex]m_1=0.585kg[/tex]
Mass of 2nd ball [tex]m_2=0.420kg[/tex]
Initial speed of 2nd ball [tex]u_{2}=0.270 m/s[/tex]
Final speed of 2nd ball [tex]v_{2}=0.220 m/s[/tex]
Angle of collision [tex]\angle=36.9 \textdegree[/tex]
a)
Generally the equation for law of conservation is mathematically given by
[tex]m_1u_1+m_2u_2=m_1v_1^2+m_2v_2^2[/tex]
The final velocity [tex]v_1[/tex] is given as
[tex]0+(0.420)(0.270)=(0.585)(v_1)^2+(0.420)(0.220)^2[/tex]
[tex](v_1)^2=\frac{(0.420)(0.270)-(0.420)(0.220)^2}{0.585}[/tex]
[tex](v_1)^2=0.1591[/tex]
[tex](v_1)=0.3989m/s[/tex]
b)
Generally the equation for law of conservation is mathematically given by
[tex]m_1u_1+m_2u_2=m_1v_1cos\theta_1+m_2\theta_2[/tex]
[tex]0+(0.420)(0.270)=(0.585)(1.511)cos\theta_1+(0.420)(0.220)cos36 \textdegree[/tex]
[tex]cos\theta_1= \frac{(0.420)(0.270)-(0.420)(0.220)cos36 \textdegree}{(0.585)(0.3989)}[/tex]
[tex]cos\theta_1=0.1656[/tex]
[tex]\theta_1=80.5 \textdegree[/tex]
c)
Generally the equation for kinetic energy is mathematically given by
[tex]K.E=\frac{1}{2} mv^2[/tex]
1st Ball
[tex]K.E=\frac{1}{2} (0.585)(0.3989)^2[/tex]
[tex]K.E=0.0465J[/tex]
2nd ball
[tex]K.E=\frac{1}{2} (0.420)(0.220)^2[/tex]
[tex]K.E=0.101J[/tex]
Therefore the change in the total kinetic energy of the two balls as a result of the collision is
[tex]0.101-0.0465[/tex]
[tex]K.E=0.036J[/tex]
On the Moon’s surface, lunar astronauts placed a corner reflector, off which a laser beam is periodically reflected. The distance to the Moon is calculated from the round-trip time. What percent correction is needed to account for the delay in time due to the slowing of light in Earth’s atmosphere? Assume the distance to the Moon is precisely 3.84×108 m , and Earth’s atmosphere (which varies in density with altitude) is equivalent to a layer 30.0 km thick with a constant index of refraction n = 1.000293.
Answers
Answer:
[tex]T_d=2.8*10^-^6\%[/tex]
Explanation:
From the question we are told that
Distance b/w Earth and the moon [tex]d_e=3.84×10^8 m[/tex]
Thickness of Earth's atmosphere[tex]d_t=30km[/tex]
Constant index of refraction [tex]n = 1.000293.[/tex]
Generally the equation for percentage of time delay [tex]T_d[/tex] is mathematically given as
[tex]T_d=\frac{d(n-1)}{rm}*100\%[/tex]
[tex]T_d=\frac{(35*10^3)(1.000293-1)()100)}{3.674*10^8} *\%[/tex]
[tex]T_d=2.8*10^-^6 \%[/tex]
Therefore the general percentage correction needed because of tym deley is given as
[tex]T_d=2.8*10^-^6\%[/tex]
An object moves in a circle with a period of 0.025 hours. What is its frequency in Hz?
Answers
Frequency, is defined as the rate of rotation, or the number of rotations in some unit of time. Angular frequency, , is the rotation rate measured in radians. These three quantities are related by f = 1 T = ω 2 π .
what is frequency ?The frequency is the number of oscillation per unit time and it is used for defining the cyclic process like rotation, oscillation, wave etc.
The SI unit of the frequency is denoted as Hertz and the symbol λ represents it where one hertz means the wave completed one cycle in one second.
The frequency which explains the phenomenon of oscillatory and vibration like the mechanical vibration, sound signals, light, frequency waves etc. The “period” represented as the time required by the wave for one oscillation, i.e., it is inversely proportional to the frequency.
If the flashes, then the period is the time between the two flashes. And the frequency is the total number of flashes per second.
For more details regarding frequency, visit
brainly.com/question/14400059
#SPJ2
What are three hazardous chemicals found in cigarette smoke?
Answers
Answer: I believe hydrogen cyanide, carbon monoxide, and ammonia are the three chemicals involved, but im not sure
What voltage indicates the voltmeter connected to the ends of a conductor, if the ammeter connected in series with this conductor indicates a current of 400 mA. The resistance of the conductor is equal to 5kΩ.
Answers
Explanation:
V= Current × Resistance
V= 400mA × 5kohms
V= 2000V
What is the difference between 1 celcius and 1 kelvin
Answers
Answer:
One degree unit on the Celcius scale is equivalent to one degree unit on the kelvin scale. The only difference between these two scales is the zero point. The zero point on the Celcius scale was defined as the freezing point of water, which means that there are higher and lower temperatures around it.
Carla has a stick of butter. What can Carla do to the butter to show a chemical change?
Answers
Answer:
melting butter in a saucepan, as the butter cools it turns brown
Explanation:
although melting the butter is a physical change, but the butter being cooked and turning brown Is a chemical change, because due to the heat, its particles are being broken down, which is irreversible, and shows a chemical change.
The gravitational force between two objects is proportional to the square of the distance between the two objects.
a. True
b. False
Answers
Answer: True!
Explanation: The force is proportional to the square of the distance between 2 point masses
Which theory states that the principle cause of forgetting is passage of time? A. motivated forgetting B. retrieval failure C. decay theory D. ineffective encoding
Answers
As time passes the information is less available for later retrieval, so that the information won’t be lost over time it is necessary to rehearse it.
how to makee them love you I AM JK U ARE BEAUTIFUL U DONT NEED A MAN GIRL GO STUDY INSTEAD OF CHECKING UR PHONE 100 TIMES A DAY. ILYYY DONT FORGET THAT
Answers
Explanation:
lol ....you are right.......
Question 7 of 10
Which of these is a product of beta decay?
O A. An alpha particle
OB. A helium nucleus
C. An electron or a positron
O D. A beam of electromagnetic radiation
Answers
Answer:
c.an electron or positron
Answer:
your answer would be c
Explanation:
What is the speed of an object moving around a 0.75 m radius circle that completes a revolution in 0.50 seconds?
Answers
Answer:
the speed of an object is 9.42 m/s
Explanation:
The computation of the speed of an object is given below:
v = 2πr ÷ t
where
v denotes the speed
r denotes the radius
r denotes the time
So,
= 2 × 3.14 × 0.75 ÷ 0.50
= 9.42 m/s
Hence, the speed of an object is 9.42 m/s
the same would be considered and relevant too
During the course of a demonstration the professor is called away. When he returns he finds a beaker of water that was at room temperature is now at a slightly higher temperature. There is a stirring rod on the desk and a cigarette lighter. The professor can assume that the temperature increase is due to either heat added or mechanical work done. mechanical work done on the system. heat added to the system.
Answers
Answer:
Either heat added or mechanical work done.
Explanation:
Since he found stirring rod on the desk and a cigarette lighter. This means that the beaker was probably either heated with the aid of fire from the lighter.
Also, the stirring rod could have been used to stir the water which will increase the kinetic energy which also means an increase in temperature.
Thus, it's either heat was added or mechanical work was done as a result of stirring.
Type the correct answer in each box. Round your answers to the nearest hundredth.
A ball with a mass of 1.5 kilograms is tied to the end of a rope. The ball is pulled to a height of 0.5 meters above the ground and released.
The ball has
joules of potential energy at position B. At position A, all of the energy changes to kinetic energy. The velocity of the ball at position A is
meters/second. Assume there’s no air resistance. Use g = 9.8 m/s2 , PE = m × g × h, and .
Answers
Hi there!
[tex]\large\boxed{PE = 7.35 J, \text{ }v \approx 3.13 m/s}[/tex]
To find the potential energy of the ball at B, we can use the equation:
PE = mgh
Plug the given gravity, mass, and height:
PE = (1.5)(0.5)(9.8) = 7.35 J
At A, all of this potential energy is changed to kinetic energy, so we can use the following equation:
v = √2KE/m
Plug in the solved for energy and mass:
v = √2(7.35)/1.5
Solve:
v ≈ 3.13 m/s
Q1. Helmut rides 5km in 2h on his bike. His speed was *
a) 10km/h
b) 2.5km/h
c) 0.4km/h
d) 2.5km
Q2. A plane is travelling at 250km/h and must reach a target that is 3h 58min away. The distance to the target is. *
a) 1000km
b) 89500km
c) 62.5km
d) not enough information
Answers
Answer:
Speed of bike = 2.5 km/h
Distance travel = 1,000 km (Approx.)
Explanation:
Given:
Distance cover by Helmut = 5 km
Time taken = 2 hour
Find:
Speed of bike
Computation:
Speed = Distance / Time
Speed of bike = 5 / 2
Speed of bike = 2.5 km/h
Given:
Speed of plane = 250 km/h
time taken = 3 hr 58 min = 3.967 hr
Find:
Distance travel
Computation:
Distance = Speed x time
Distance travel = 250 x 3.967
Distance travel = 991.669
Distance travel = 1,000 km (Approx.)
51.Shoveling snow can be extremely taxing because the arms have such a low efficiency in this activity. Suppose a person shoveling a footpath metabolizes food at the rate of 800 W. (a) What is her useful power output? (b) How long will it take her to lift 3000 kg of snow 1.20 m? (This could be the amount of heavy snow on 20 m of footpath.) (c) How much waste heat transfer in kilojoules will she generate in the process?
Answers
Complete question is;
Shoveling snow can be extremely taxing since the arms have such a low efficiency in this activity. Suppose a person shoveling a sidewalk metabolizes food at the rate of 800 W. (The efficiency of a person shoveling is 3%.)
(a) What is her useful power output? (b) How long will it take her to lift 3000 kg of snow 1.20 m? (This could be the amount of heavy snow on 20 m of footpath.) (c) How much waste heat transfer in kilojoules will she generate in the process?
Answer:
A) P_out = 24 W
B) t = 1470 s
C) Q = 1140.72 KJ
Explanation:
We are given;
Input Power; P_in = 800 W
Efficiency; η = 3% = 0.03
A) Formula for efficiency is;
η = P_out/P_in
Making P_out the subject, we have;
P_out = η•P_in
P_out = 0.03 × 800
P_out = 24 W
B) We know that;
Power = work done/time taken
Thus;
P_out = mgh/t
We are given;
m = 3000 kg
h = 1.20 m
Thus, time is;
t = (3000 × 9.8 × 1.2)/24
t = 1470 s
C) amount of heat wasted is calculated from;
Q = (P_in - P_out)t
Q = (800 - 24) × 1470
Q = 1,140,720 J
Q = 1140.72 KJ
If the motion of B is uniformly accelerated, at what time will both graphs have
exactly the same slope? Explain.
Answers
Answer:
Im just here for the points man sorry
Explanation:
Compare and contrast the strength of the forces between two objects with a mass of 1 kg each, a charge of 10
and at a distance of 1 m from each other.
Answers
Answer:
Let's see the similarities between the two forces
* are proportional to the product of a magnitude, mass or charge
* They are inversely proportional to the square of the distance
* They are long-range forces since zero is not made up to an infinite distance. The gravitational force is always attractive, the electrical force can be attractive or repulsive.
The differences in them
* The electric force in much greater than the gravitational force
* The gravitational force is always attractive, the electrical force can be attractive or repulsive.
Explanation:
Let's start by calculating each force.
Gravitational force
F =[tex]G \frac{m_1m_2}{r^2}[/tex]
let's calculate
F = 6.67 10⁻¹¹ 1 1 / 1²
F = 6.67 10⁻¹¹ N
Electric force
F = [tex]k \frac{q_1q_2}{r^2}[/tex]
indicates that the charge is q = 10 C
F = 9 10⁹ 10 10 / 1²
F = 9 10¹¹ N
Let's see the similarities between the two forces
* are proportional to the product of a magnitude, mass or charge
* They are inversely proportional to the square of the distance
* They are long-range forces since zero is not made up to an infinite distance. The gravitational force is always attractive, the electrical force can be attractive or repulsive.
The differences in them
* The electric force in much greater than the gravitational force
* The gravitational force is always attractive, the electrical force can be attractive or repulsive.
a ball rolls horizontally of the edge of the cliff at 4 m/s, if the ball lands at a distance of 30 m from the base of the vertical cliff, what is the the hight of the cliff
Answers
Answer:
Approximately [tex]281.25\; \rm m[/tex]. (Assuming that the drag on this ball is negligible, and that [tex]g = 10\; \rm m \cdot s^{-2}[/tex].)
Explanation:
Assume that the drag (air friction) on this ball is negligible. Motion of this ball during the descent:
Horizontal: no acceleration, velocity is constant (at [tex]v(\text{horizontal})[/tex] is constant throughout the descent.)Vertical: constant downward acceleration at [tex]g = 10\; \rm m \cdot s^{-2}[/tex], starting at [tex]0\; \rm m \cdot s^{-1}[/tex].The horizontal velocity of this ball is constant during the descent. The horizontal distance that the ball has travelled during the descent is also given: [tex]x(\text{horizontal}) = 30\; \rm m[/tex]. Combine these two quantities to find the duration of this descent:
[tex]\begin{aligned}t &= \frac{x(\text{horizontal})}{v(\text{horizontal})} \\ &= \frac{30\; \rm m}{4\; \rm m \cdot s^{-1}} = 7.5\; \rm s\end{aligned}[/tex].
In other words, the ball in this question start at a vertical velocity of [tex]u = 0\; \rm m \cdot s^{-1}[/tex], accelerated downwards at [tex]g = 10\; \rm m \cdot s^{-2}[/tex], and reached the ground after [tex]t = 7.5\; \rm s[/tex].
Apply the SUVAT equation [tex]\displaystyle x(\text{vertical}) = -\frac{1}{2}\, g \cdot t^{2} + v_0\cdot t[/tex] to find the vertical displacement of this ball.
[tex]\begin{aligned}& x(\text{vertical}) \\[0.5em] &= -\frac{1}{2}\, g \cdot t^{2} + v_0\cdot t\\[0.5em] &= - \frac{1}{2} \times 10\; \rm m \cdot s^{-2} \times (7.5\; \rm s)^{2} \\ & \quad \quad + 0\; \rm m \cdot s^{-1} \times 7.5\; s \\[0.5em] &= -281.25\; \rm m\end{aligned}[/tex].
In other words, the ball is [tex]281.25\; \rm m[/tex] below where it was before the descent (hence the negative sign in front of the number.) The height of this cliff would be [tex]281.25\; \rm m\![/tex].
Which of the following phenomena best demonstrates that light possesses wave characteristics?
A.The different colors of visible light
B.The transfer of electrons
C.The release of infrared light form radioactive materials
D.It shines and takes up space
Answers
The release of infrared light from radioactive materials is what demonstrates light possessing wave characteristics.
What is a Wave?This is defined as the propagation of disturbances from one place to another in an organized way.
The release of waves in a diffraction pattern is why option C was chosen as the most appropriate choice.
Read more about Wave here https://brainly.com/question/15663649