The ratio of heat flow between a house with brick walls and a house with wood walls, given that the brick walls are twice as thick as the wood walls. the wood house will be relatively cooler in the summer due to its lower thermal conductivity and reduced heat transfer.
According to Fourier's law of heat conduction, the heat flow through a material is proportional to its thermal conductivity and inversely proportional to its thickness. In this case, since the brick walls are twice as thick as the wood walls, the ratio of heat flow can be determined using the ratio of thermal conductivities.
The ratio of heat flow from the brick house to the wood house can be calculated by dividing the product of the thermal conductivity of brick (K brick) and the inverse of the thickness of the brick walls by the product of the thermal conductivity of wood (K wood) and the inverse of the thickness of the wood walls.
In terms of which house gets warmer in the winter and colder in the summer, the answer depends on the relative thermal conductivities of brick and wood. Since brick has a higher thermal conductivity (K brick = 0.72 W/m°C) compared to wood (K wood = 0.17 W/m°C), the brick house will have a higher heat flow and thus be warmer in the winter. Conversely, in the summer, the brick house will also be hotter due to its higher thermal conductivity, resulting in increased heat transfer from the outside to the inside. Therefore, the wood house will be relatively cooler in the summer due to its lower thermal conductivity and reduced heat transfer.
Learn more about thermal conductivity:
https://brainly.com/question/14553214
#SPJ11
The ratio of brick house heat flow to wood house heat flow is greater than 1. The brick house will have a higher heat flow( More Thermal Conductivity) compared to the wood house. In the winter.
According to Fourier's law of heat conduction, the heat flow through a material is proportional to its thermal conductivity and inversely proportional to its thickness. In this case, since the brick walls are twice as thick as the wood walls, the ratio of heat flow can be determined using the ratio of thermal conductivities.
The ratio of heat flow from the brick house to the wood house can be calculated by dividing the product of the thermal conductivity of brick (K brick) and the inverse of the thickness of the brick walls by the product of the thermal conductivity of wood (K wood) and the inverse of the thickness of the wood walls.
In terms of which house gets warmer in the winter and colder in the summer, the answer depends on the relative thermal conductivities of brick and wood. Since brick has a higher thermal conductivity (K brick = 0.72 W/m°C) compared to wood (K wood = 0.17 W/m°C), the brick house will have a higher heat flow and thus be warmer in the winter. Conversely, in the summer, the brick house will also be hotter due to its higher thermal conductivity, resulting in increased heat transfer from the outside to the inside. Therefore, the wood house will be relatively cooler in the summer due to its lower thermal conductivity and reduced heat transfer.
Learn more about thermal conductivity:
brainly.com/question/14553214
#SPJ11
Solve the following initial value problem.
y'' + 9y = 4x; y(0) = 1, y'(0)=3
The specific solution to the initial value problem is:
y(x) = cos(3x) + (23/27)sin(3x) + (4/9)x
To solve the given initial value problem, y'' + 9y = 4x, with initial conditions y(0) = 1 and y'(0) = 3, we can use the method of undetermined coefficients.
1. First, we need to find the complementary solution to the homogeneous equation y'' + 9y = 0. The characteristic equation is r^2 + 9 = 0, which has complex roots: r = ±3i. Therefore, the complementary solution is y_c(x) = c1cos(3x) + c2sin(3x), where c1 and c2 are arbitrary constants.
2. Next, we need to find the particular solution to the non-homogeneous equation y'' + 9y = 4x. Since the right-hand side is a linear function of x, we assume a particular solution of the form y_p(x) = ax + b. Substituting this into the equation, we get:
y'' + 9y = 4x
(0) + 9(ax + b) = 4x
9ax + 9b = 4x
To satisfy this equation, we equate the coefficients of like terms:
9a = 4 (coefficient of x)
9b = 0 (constant term)
Solving these equations, we find a = 4/9 and b = 0. Therefore, the particular solution is y_p(x) = (4/9)x.
3. Finally, we combine the complementary and particular solutions to get the general solution: y(x) = y_c(x) + y_p(x).
y(x) = c1cos(3x) + c2sin(3x) + (4/9)x
4. To find the specific values of c1 and c2, we use the initial conditions y(0) = 1 and y'(0) = 3.
Substituting x = 0 into the general solution:
y(0) = c1cos(0) + c2sin(0) + (4/9)(0)
1 = c1
Differentiating the general solution with respect to x and then substituting x = 0:
y'(x) = -3c1sin(3x) + 3c2cos(3x) + 4/9
y'(0) = -3c1sin(0) + 3c2cos(0) + 4/9
3 = 3c2 + 4/9
27/9 - 4/9 = 3c2
23/9 = 3c2
c2 = 23/27
5. Therefore, the specific solution to the initial value problem is:
y(x) = cos(3x) + (23/27)sin(3x) + (4/9)x
To learn more about general solution
https://brainly.com/question/30285644
#SPJ11
13- w(x) = 24√x 24√x N/m A 370 Draw free body diagram. OA=1m |OB|=12 m |OC| = 16 m nota: takes the rasotion force at A, ac perpendicular to the inclined curtoe. N F MA.. 53⁰ C A O A 9,6 m- 370 9
The free body diagram for point A is as follows:
```
O
|
A
```
In the free body diagram, we represent the point A as a dot and show the forces acting on it. Here is the breakdown of the forces:
1. Weight (W): The weight acts vertically downward and can be calculated using the formula W = mg, where m is the mass and g is the acceleration due to gravity. Since the mass is not given, we cannot determine the exact value of the weight. However, we can represent it as a vertical force acting downward from point A.
2. Normal force (N): The normal force acts perpendicular to the surface of contact. In this case, since point A is not in contact with any surface, there is no normal force acting on it.
3. Force at A: There is a force acting at point A, which is directed along the inclined curve. We can represent this force as a vector pointing from O to A.
4. Moment (MA): The moment at point A is not specified in the question. Hence, we cannot determine its value or direction without further information.
Note: The given lengths OA, OB, and OC are not directly relevant to the free body diagram. They represent the distances between different points in the system, but they do not affect the forces acting on point A.
Therefore, the free body diagram for point A includes the weight (directed downward) and the force at A (directed along the inclined curve). The normal force is not present since there is no surface in contact with point A. The moment (MA) is not specified.
Learn more about gravity:
https://brainly.com/question/940770
#SPJ11
Compute the maximum bending at 40′ away from the left support of 120′ simply supported beam subjected to the following wheel loads shown in Fig. Q. 2(b).
The maximum bending moment at 40 ft away from the left support is 135600 in-lb or 11300 ft-lb.
Given that, Length of the beam, L = 120 ft Distance of the point of interest from the left end of the beam, x = 40 ft Wheel loads, P1 = 15 kips, P2 = 10 kips, and P3 = 20 kips Wheel loads' distances from the left end of the beam, a1 = 30 ft, a2 = 50 ft, and a3 = 80 ft.
The bending moment at the point of interest can be calculated using the equation for bending moment at a point in a simply supported beam, M = (Pb - Wx) × (L - x)
Pb = Pa = (P1 + P2 + P3)/2W is the total load on the beam, which can be calculated as W[tex]= P1 + P2 + P3= 15 + 10 + 20 = 45[/tex]kips For x = 40 ft, we have,
[tex]Pb = (P1 + P2 + P3)/2= (15 + 10 + 20)/2= 22.5 kip[/tex]s
W = 45 kips
M = (Pb - Wx) × (L - x)
= [tex](22.5 - 45 × 40) × (120 - 40)[/tex]
= (-[tex]1695) ×[/tex] 80
= [tex]-135600 in-lb or -11300 ft-l[/tex]b.
Therefore,
To know more about distances visit:
https://brainly.com/question/33573730
#SPJ11
A groundwater source is contaminated by Chemical X at a concentration of 38 µg/L. You are hired as an environmental engineer to decrease that concentration to 9 µg/L by adding activated carbon. According to the literature, the Freundlich isotherm coefficients for activated carbon are K₂ -0.04 and n = 2.1 for concentrations in mg/L. Calculate the mass of activated carbon (in mg) needed for 2 L of water. Enter your final answer with 2 decimal places. 0.183
The mass of activated carbon (in mg) needed for 2 L of water is 183 mg. Given, The initial concentration of Chemical X = 38 µg/L,Therefore, the mass of activated carbon (in mg) needed for 2 L of water is 183 mg.
The required concentration of Chemical X after treatment = 9 µg/L
The volume of water to be treated = 2L
The Freundlich isotherm coefficients for activated carbon are K₂ = 0.04 and
n = 2.1 for concentrations in mg/L.
We have to calculate the mass of activated carbon (in mg) needed for 2 L of water. Activated carbon is commonly used in water filtration processes, owing to its high surface area and capacity to adsorb a variety of organic and inorganic compounds.
Freundlich adsorption isotherm, a relationship that relates the amount of solute adsorbed to its equilibrium concentration in the solution, is frequently used to describe activated carbon adsorption.The Freundlich isotherm formula is: Q = Kf * C^(1/n Where Q = Mass of adsorbate adsorbed per unit weight of the adsorbent Kf and n are Freundlich constants = Concentration of adsorbate in solution first, we need to convert the initial and required concentration of Chemical X from µg/L to mg/L.
To know more about initial visit:
https://brainly.com/question/29046615
#SPJ11
The mass of activated carbon needed for 2 L of water is approximately 0.183 mg.
To calculate the mass of activated carbon needed to decrease the concentration of Chemical X in the groundwater source, we can use the Freundlich isotherm equation.
First, convert the concentrations to mg/L. 38 µg/L is equal to 0.038 mg/L, and 9 µg/L is equal to 0.009 mg/L.
The Freundlich isotherm equation is expressed as follows:
C = K * (1/m) * (X^(1/n))
Where C is the concentration of Chemical X in mg/L, K is the Freundlich isotherm coefficient, X is the mass of activated carbon in mg, m is the mass of water in L, and n is another coefficient.
In this case, we know that C₁ = 0.038 mg/L, C₂ = 0.009 mg/L, and m = 2 L. We are trying to find X.
To solve for X, we can rearrange the equation:
X = (C₂ / C₁)^(1/n) * K * m
Plugging in the values, we get:
X = (0.009 / 0.038)^(1/2.1) * -0.04 * 2
Calculating this, we find that the mass of activated carbon needed for 2 L of water is approximately 0.183 mg.
Learn more about mass
https://brainly.com/question/11954533
#SPJ11
QUESTION 2 (10/100) Calculate density of 10 API Gravity oil in the unit of kg QUESTION 3 (20/100) If the flow rate of oil is 1 million bbl per day in 48 inch diameter pipeline, calculate the flow velocity in the unit of m³/s (Reminder: 1 barrel = 150000 cm³
The flow velocity in the 48-inch diameter pipeline is approximately 0.1283 m³/s.
To calculate the density of 10 API Gravity oil in the unit of kg, we can use the following formula:
density (kg/m³) = 141.5 / (API Gravity + 131.5)
For 10 API Gravity oil, let's substitute the value into the formula:
density = 141.5 / (10 + 131.5) = 0.984 kg/m³
Therefore, the density of 10 API Gravity oil is approximately 0.984 kg/m³.
Moving on to the second question, to calculate the flow velocity in m³/s for a flow rate of 1 million bbl per day in a 48-inch diameter pipeline, we need to convert the flow rate from barrels to cubic meters and divide it by the cross-sectional area of the pipeline.
First, let's convert 1 million barrels per day to cubic meters per second. Given that 1 barrel is equal to 150000 cm³, we can convert it to cubic meters using the following conversion factor:
1 barrel = 150000 cm³ = 0.15 m³
Next, we need to calculate the cross-sectional area of the pipeline using its diameter. The formula for the cross-sectional area of a circle is:
A = π * r²
Since the diameter is given as 48 inches, we need to convert it to meters:
48 inches = 48 * 0.0254 = 1.2192 meters
Now we can calculate the radius:
r = diameter / 2 = 1.2192 / 2 = 0.6096 meters
Using the radius, we can calculate the cross-sectional area:
A = π * (0.6096)² ≈ 1.1664 m²
Finally, we can calculate the flow velocity:
velocity = flow rate / cross-sectional area
= 1 million bbl/day * 0.15 m³/bbl / 1 day / 1.1664 m²
≈ 0.1283 m³/s
Therefore, the flow velocity in the 48-inch diameter pipeline is approximately 0.1283 m³/s.
Learn more about velocity on
https://brainly.com/question/80295
#SPJ11
help me pleaseee!!!!!
Answer: 37.5%
Step-by-step explanation:
There are 8 separate area
and among them are 3 Cs.
Thus the probability is
⅜ times 100 = 37.5 (%)
What is the equilibrium constant of the following reaction at 25˚C?AlBr₃(aq) + Rb₃PO₄(aq) ⇄ 3RbBr(aq) + AlPO₄(s):1)1.02 × 10²⁰ 2)1.0 × 10⁻⁷ 3)9.80 × 10⁻²¹ 4)1.02 × 10³⁴ 5)9.80 × 10⁻³⁵
The answer to the question is that we cannot determine the equilibrium constant of the reaction at 25˚C based on the given information.
The equilibrium constant, K, is a measure of the ratio of products to reactants at equilibrium for a given reaction. It is calculated using the concentrations of the species involved in the reaction.
To calculate the equilibrium constant for the reaction AlBr₃(aq) + Rb₃PO₄(aq) ⇄ 3RbBr(aq) + AlPO₄(s), we need to use the concentrations of the species involved. Unfortunately, we don't have that information provided in the question.
The equilibrium constant, K, is calculated by taking the product of the concentrations of the products, raised to the power of their coefficients, divided by the product of the concentrations of the reactants, raised to the power of their coefficients.
Since we don't have the concentrations of the species, we cannot calculate the equilibrium constant for this reaction.
Therefore, the answer to the question is that we cannot determine the equilibrium constant of the reaction at 25˚C based on the given information.
Learn more about equilibrium constant:
brainly.com/question/27549059
#SPJ11
Question 4 Describe the production process of methanol as a petrochemical feedstock. (20 marks)
Methanol is produced by converting natural gas or coal into syngas, followed by catalytic conversion to methanol, purification to remove impurities, and finally, storage and distribution for utilization as a petrochemical feedstock.
Methanol, an essential petrochemical feedstock, is produced through the following steps:
1. Feedstock Preparation: Natural gas or coal is commonly used as the primary feedstock. Natural gas is first converted into synthesis gas (syngas) through steam reforming or partial oxidation. Coal, on the other hand, is gasified to produce syngas.
2. Syngas Production: Syngas is a mixture of hydrogen (H₂) and carbon monoxide (CO). It is obtained by reacting the feedstock with steam or oxygen in a reformer or gasifier. The choice of technology depends on the feedstock used.
3. Catalytic Conversion: The syngas is then passed over a catalyst (usually copper or zinc oxide) in a reactor, where it undergoes the catalytic conversion known as the methanol synthesis reaction. This reaction involves the combination of CO and H₂ to form methanol (CH₃OH).
4. Purification: The produced methanol is typically impure and contains water, trace impurities, and unreacted gases. To purify it, processes such as distillation, pressure swing adsorption, and molecular sieves are employed to remove impurities and increase the methanol concentration.
5. Storage and Distribution: The purified methanol is stored in tanks or transported via pipelines, tankers, or railcars to end-users, where it serves as a feedstock for various chemical processes, such as the production of formaldehyde, acetic acid, and other derivatives.
Learn more About Methanol from the given link
https://brainly.com/question/14889608
#SPJ11
A steady, incompressible, two-dimensional velocity field is given by V = (u, v) = (0.5 +0.8x) 7+ (1.5-0.8y)] Calculate the material acceleration at the point (X-3 cm, y=5 cm). Just provide final answers. (1)
The material acceleration at the point (x = 3 cm,
y = 5 cm) is (2.88, 4.16) cm/s².
Given the velocity field: V = (u, v)
= [(0.5 + 0.8x) 7 + (1.5 - 0.8y)]
To calculate the material acceleration at the point (x = 3 cm,
y = 5 cm) the expression for acceleration is given as:
a = ∂v/∂t + V . ∇V
The equation represents the sum of the acceleration due to change of velocity with time and acceleration due to change in direction of flow. Let's begin with calculating the material acceleration by using the given information.
So, we have:
V = (u, v)
= [(0.5 + 0.8x) 7 + (1.5 - 0.8y)]
On substituting the values of x and y in V, we get
V = (u, v)
= [(0.5 + 0.8 × 3) 7 + (1.5 - 0.8 × 5)]
= (6.1, -2.7)
The time derivative of the velocity field is:
∂v/∂t = (∂u/∂t, ∂v/∂t)
= 0 (since it is given steady)
Now, we calculate the gradient of the velocity field as:
∇V = [(∂u/∂x), (∂v/∂y)]
= [0.8, -0.8]
Therefore, the material acceleration is calculated using the equation:
a = ∂v/∂t + V . ∇V
a = 0 + (6.1, -2.7) . [0.8, -0.8]
= (2.88, 4.16) cm/s²
The material acceleration at the point (x = 3 cm,
y = 5 cm) is (2.88, 4.16) cm/s².
To know more about acceleration visit
https://brainly.com/question/16710160
#SPJ11
Consider the differential equation: y ′′ + y = sin x . (a) Undetermined Coefficient (b) Variation of parameter (c) Reduction of order You should not use any formula for variation of parameter and reduction of order. For any difficult integration, feel free to use "Wolfram Alpha", "Symbolab" or any other computing technology.
The solution to the given differential equation is y = c1cos(x) + c2sin(x) - x/2*cos(x).
To solve the given differential equation y'' + y = sin(x), we will use the method of Undetermined Coefficients. This method involves assuming a particular solution for the nonhomogeneous equation and determining the coefficients based on the form of the forcing function.
Step 1: Find the complementary function (CF):
The complementary function solves the associated homogeneous equation y'' + y = 0. This can be solved by assuming y = e^(mx), where m is a constant. Substituting this into the equation, we get the characteristic equation m^2 + 1 = 0, which gives us the solutions m = ±i. Therefore, the CF is yCF = c1cos(x) + c2sin(x), where c1 and c2 are arbitrary constants.
Step 2: Assume the particular solution (PS):
For the nonhomogeneous part, sin(x), we assume a particular solution of the form yPS = Asin(x) + Bcos(x), where A and B are undetermined coefficients.
Step 3: Find the derivatives of the assumed PS:
yPS' = Acos(x) - Bsin(x)
yPS'' = -Asin(x) - Bcos(x)
Step 4: Substitute the assumed PS and its derivatives into the original equation:
(-Asin(x) - Bcos(x)) + (Asin(x) + Bcos(x)) = sin(x)
Step 5: Equate the coefficients of sin(x) on both sides:
-Asin(x) + Asin(x) = sin(x)
This gives us 0 = sin(x), which is not possible. Thus, the assumed PS does not satisfy the equation.
To resolve this, we introduce an additional factor of x in the assumed PS:
yPS = x(Asin(x) + Bcos(x))
Repeating steps 3 and 4 with the modified PS gives us:
yPS' = x(Acos(x) - Bsin(x)) + Asin(x) + Bcos(x)
yPS'' = -x(Asin(x) + Bcos(x)) + 2Acos(x) - 2Bsin(x)
Substituting these derivatives into the original equation:
(-x(Asin(x) + Bcos(x)) + 2Acos(x) - 2Bsin(x)) + x(Asin(x) + Bcos(x)) = sin(x)
Simplifying the equation:
(-x(Asin(x) + Bcos(x)) + x(Asin(x) + Bcos(x))) + (2Acos(x) - 2Bsin(x)) = sin(x)
2Acos(x) - 2Bsin(x) = sin(x)
Equate the coefficients of cos(x) and sin(x) on both sides:
2A = 0, -2B = 1
A = 0, B = -1/2
Hence, the particular solution is yPS = -x/2*cos(x).
Step 6: Find the general solution:
The general solution is the sum of the CF and the PS:
y = yCF + yPS
= c1cos(x) + c2sin(x) - x/2*cos(x)
Learn more about differential equation
https://brainly.com/question/1164377
#SPJ11
For the matrix A below, find a nonzero vector in Nul A and a nonzero vector in Col A A = 125 013-7 0 A nonzero vector in Nul A is (Type an integer or decimal for each matrix element) A nonzero vector in Col A is (Type an integer or decimal for each matrix element)
A nonzero vector in Col A is: b(x₁, x₂, x₃) = (0, 1, 0) So, a nonzero vector in Null A is (13/7, -3, 1), and a nonzero vector in Col A is (0, 1, 0).
To find a nonzero vector in the nullspace (Nul A) and a nonzero vector in the column space (Col A) of matrix A, we first need to understand the properties of the given matrix.
The matrix A is:
[tex]A=\left[\begin{array}{ccc}1&2&5\\0&1&3\\-7&0&13\end{array}\right][/tex]
To find a nonzero vector in the nullspace (Nul A), we need to find a vector x such that Ax = 0, where 0 is the zero vector.
Setting up the equation Ax = 0, we have:
[tex]A\times x=\left[\begin{array}{ccc}1&2&5\\0&1&3\\-7&0&13\end{array}\right]*\ \begin{bmatrix}x_1 \\x_2 \\x_3\end{bmatrix}[/tex]
Expanding the matrix multiplication, we get:
x₁ + 2x₂ + 5x₃ = 0 --------- (1)
x₂ + 3x₃ = 0 --------- (2)
-7x₁ + 13x₃ = 0 --------- (3)
To find a nonzero solution for x, we can set x₃ = 1 and solve the system of equations.
Let's set x₃ = 1 and solve for x₁ and x₂.
Using Equation 2:
x₂ + 3(1) = 0
x₂ + 3 = 0
x₂ = -3
Using Equation 3:
-7x₁ + 13(1) = 0
-7x₁ + 13 = 0
-7x₁ = -13
x₁ = 13/7
Therefore, a nonzero vector in Nul A is:
(x₁, x₂, x₃) = (13/7, -3, 1)
To find a nonzero vector in the column space (Col A), we need to find a vector b such that there exists a vector x satisfying Ax = b.
We can choose a vector b that is in the column space of A. For example, let's choose b as the second column of A:
[tex]b=\begin{bmatrix}2 \\1 \\0\end{bmatrix}[/tex]
Now, we need to find a vector x such that Ax = b.
Setting up the equation Ax = b, we have:
[tex]A\times x=\left[\begin{array}{ccc}1&2&5\\0&1&3\\-7&0&13\end{array}\right]*\ \begin{bmatrix}x_1 \\x_2 \\x_3\end{bmatrix}\ =\begin{bmatrix}2 \\1\\0\end{bmatrix}[/tex]
Expanding the matrix multiplication, we get:
x₁ + 2x₂ + 5x₃ = 2 ----------- (4)
x₂ + 3x₃ = 1 ----------- (5)
-7x₁ + 13x₃ = 0 ----------- (6)
We can solve this system of equations to find the values of x₁, x₂, and x₃. However, we can observe that Equation 6 already implies that x₁ = 0, since -7x₁ + 13x₃ = 0.
Using Equation 4:
0 + 2x₂ + 5x₃ = 2
2x₂ + 5x₃ = 2
Using Equation 5:
x₂ + 3x₃ = 1
We can solve these two equations to find the values of x₂ and x₃.
From Equation 5, we can rewrite it as:
x₂ = 1 - 3x₃
Substituting this value of x₂ in
Equation 4, we get:
2(1 - 3x₃) + 5x₃ = 2
2 - 6x₃ + 5x₃ = 2
-x₃ = 0
x₃ = 0
Substituting the value of x₃ = 0 in x₂ = 1 - 3x₃, we get:
x₂ = 1 - 3(0)
x₂ = 1
Therefore, a nonzero vector in Col A is:
(x₁, x₂, x₃) = (0, 1, 0)
So, a nonzero vector in Nul A is (13/7, -3, 1), and a nonzero vector in Col A is (0, 1, 0).
To know more about matrix visit:
https://brainly.com/question/33840317
#SPJ11
answer from the picture
Answer:4
Step-by-step explanation:
no
Q6. The BOD5 test was run on a domestic wastewater sample at 30∘C. The ratio between wastewater and distilled water in the BOD bottle was 1:10. Given the concentrations of initial and final dissolved oxygen as 8.5 and 2.3mg/L, and BOD rate constant at 20∘C equals 0.22 day −1, the value of BOD5 at 30∘C equals: A. 62mg/L B. 0.62mg/L C. 35mg/L D. 45mg/L Q7. A suspended solid test was conducted on a raw sewage sample. A volume of 150 mL of the sewage was filtered. The weight of the filter paper before the test was 0.1285 g. After filtration and drying the paper at 103∘C, the paper weighed 0.1465 g. The total suspended solids concentration is: A. 12mg/L B. 120mg/L C. 360mg/L D. 36mg/L Q8. What is the purpose of preliminary treatment? A. Oil and grease removal B. Plastic removal C. Rags removal D. All of the above Q9. The minimum hydraulic retention time for clarifier is: A. 0.5 hour B. 1 hour C. 2 hours D. 3 hours Q10. Trickling filter is a: A. Completely mixed reactor B. Plug flow reactor C. Bottom up reactor D. Batch reactor
The BOD5 test was performed on a sample of domestic wastewater at a temperature of 30∘C. The ratio of wastewater to distilled water in the BOD bottle was 1:10. Given the initial and final concentrations of dissolved oxygen as 8.5 and 2.3mg/L, and a BOD rate constant of 0.22 day−1 at 20∘C, the value of BOD5 at 30∘C can be calculated as follows:
The BOD rate constant at 30°C would be approximately 2.5 times greater than at 20°C, according to the relationship between BOD rate constant and temperature. Thus, the BOD rate constant at 30°C will be:
0.22 x ([tex]1.047^{10-1[/tex]) = 0.48 day-1
Assuming that the BOD of the sample is x, the oxygen consumed by the seed and dilution water needs to be calculated first.
Oxygen consumed by the seed and dilution water = 8.5 − 2.3 = 6.2mg/L.
BOD5 = [oxygen consumed by x (initial DO - final DO) – oxygen consumed by seed and dilution water] / (seed volume) = (6.2x) / 0.1 = 62 mg/L
A suspended solid test was conducted on a raw sewage sample. A volume of 150 mL of the sewage was filtered. The weight of the filter paper before the test was 0.1285 g. After filtration and drying the paper at 103∘C, the paper weighed 0.1465 g. The total suspended solids concentration can be calculated as follows:
Total suspended solids = (final weight of filter paper – initial weight of filter paper) / (volume of sample filtered)
Total suspended solids = (0.1465 – 0.1285) / 0.150
Total suspended solids = 0.12 g/L
Total suspended solids = 120 mg/L
Preliminary treatment is essential for removing large materials like plastics, rags, and grit that may obstruct the operation and maintenance of the wastewater treatment plant. Therefore, the correct answer is (D) All of the above.
The minimum hydraulic retention time for the clarifier is 2 hours, which is required to allow solids to settle. Therefore, the correct answer is (C) 2 hours.
The trickling filter is a type of attached growth biological reactor, specifically an example of a plug-flow reactor. Therefore, the correct answer is (B) Plug flow reactor.
To know more about temperature visit :
https://brainly.com/question/14532989
#SPJ11
(Trig) Find the missing sides or angles from the right triangles
The measure of the missing side length of the right triangle is approximately 32.1.
What is the measure of the missing side length?The figure in the image is a right triangle.
From the image:
Angle θ = 0.646 rad
Opposite to angle θ = 19.3
Hypotenuse =?
To solve for the missing side length, we use the trigonometric ratio.
Note that: sine = opposite / hypotensue
Plug the given values into the above formula and solve for the hypotenuse.
sin( θ ) = opposite / hypotenuse
sin( 0.646 rad ) = 19.3 / hypotenuse
Hypotenuse = 19.3 / sin( 0.646 rad )
Hypotenuse = 32.1
Therefore, the hypotenuse measures 32.1 units.
Learn more about trigonometric ratio here: brainly.com/question/28016662
#SPJ1
The quadratic equation x^2−2x+1=0 has discriminant and solutions as follows: Δ=0 and x=−1 Δ=0 and x=1 Δ=0 and x=±1 Δ=4 and x=±1
The solutions to the quadratic equation x^2 - 2x + 1 = 0 are x = -1 and x = 1.
The discriminant (Δ) of a quadratic equation is a value that can be calculated using the formula Δ = b^2 - 4ac, where a, b, and c are the coefficients of the quadratic equation ax^2 + bx + c = 0.
In the given quadratic equation x^2 - 2x + 1 = 0, we can compare it to the general form ax^2 + bx + c = 0 and identify that a = 1, b = -2, and c = 1.
Now, let's calculate the discriminant:
Δ = (-2)^2 - 4(1)(1) = 4 - 4 = 0
The discriminant is zero (Δ = 0).
When the discriminant is zero, it indicates that the quadratic equation has only one real solution. In this case, since Δ = 0, the equation x^2 - 2x + 1 = 0 has two equal solutions.
We can find the solutions by applying the quadratic formula:
x = (-b ± √Δ) / (2a)
Plugging in the values, we have:
x = (-(-2) ± √0) / (2(1)) = (2 ± 0) / 2 = 2 / 2 = 1
So, the solutions to the equation x^2 - 2x + 1 = 0 are x = -1 and x = 1.
Hence, the correct statement is: Δ = 0 and x = ±1.
Learn more about quadratic equation from the given link
https://brainly.com/question/1214333
#SPJ11
Suppose you have a 205 mL sample of carbon dioxide gas that was subjected to a temperature change from 22°C to −30° C as well as a change in pressure from 1.00 atm to 0.474 atm. What is the final volume of the gas after these changes occur?
[tex]V₂ = (1.00 atm * 205 mL * 243.15 K) / (0.474 atm * 295.15 K)[/tex]
Calculating this expression will give us the final volume of the gas after the changes occur.
The final volume of a 205 mL sample of carbon dioxide gas is determined after subjecting it to a temperature change from 22°C to -30°C and a change in pressure from 1.00 atm to 0.474 atm.
To calculate the final volume, we can use the combined gas law, which states that the ratio of initial pressure multiplied by the initial volume divided by the initial temperature is equal to the ratio of final pressure multiplied by the final volume divided by the final temperature. Mathematically, it can be represented as follows:
[tex](P₁ * V₁) / T₁ = (P₂ * V₂) / T₂[/tex]
Given:
Initial volume (V₁) = 205 mL
Initial temperature (T₁) = 22°C + 273.15 = 295.15 K
Initial pressure (P₁) = 1.00 atm
Final temperature (T₂) = -30°C + 273.15 = 243.15 K
Final pressure (P₂) = 0.474 atm
Using the combined gas law equation, we can rearrange it to solve for the final volume (V₂):
V₂ = (P₁ * V₁ * T₂) / (P₂ * T₁)
Substituting the given values into the equation, we get:
V₂ = (1.00 atm * 205 mL * 243.15 K) / (0.474 atm * 295.15 K)
Calculating this expression will give us the final volume of the gas after the changes occur.
Learn more about final volume from the given link:
https://brainly.com/question/22012954
#SPJ11
In a bakery, water is forced through pipe A at 150 liters per second on (sg = 0.8) is forced through pipe B at 30 liters per second Assume ideal mixing of incompressible fluids and the mixture of oil and water form globules and exits through pipe C. Evaluate the specific gravity of the mixture exiting through the pipe C A) 0.385 B)0.976 C) 0.257 D) 0.865
Specific gravity cannot be determined without the specific gravity of the oil.
To determine the specific gravity of the mixture exiting through pipe C, we need to consider the flow rates and specific gravities of the fluids flowing through pipes A and B.
Given that water is flowing through pipe A at 150 liters per second and its specific gravity is 0.8, we can calculate the volumetric flow rate of water as 150 liters per second.
Similarly, for pipe B, oil is flowing at a rate of 30 liters per second. However, we do not have the specific gravity of the oil mentioned in the question, which is necessary to calculate the mixture's specific gravity.
Without knowing the specific gravity of the oil, it is not possible to determine the specific gravity of the mixture exiting through pipe C. Therefore, none of the options A, B, C, or D can be confirmed as the correct answer.
To learn more about “gravity” refer to the https://brainly.com/question/940770
#SPJ11
I NEED HELP ON THIS ASAP!!
The best measure of center is the mean
The are 20 students represented by the whisker
The percentage of classrooms with 23 or more is 25%
The percentage of classrooms with 17 to 23 is 50%
The best measure of centerFrom the question, we have the following parameters that can be used in our computation:
The box plot
There are no outlier on the boxplot
This means that the best measure of center is mean
The students in the whiskerHere, we calculate the range
So, we have
Range = 30 - 10
Evaluate
Range = 20
The percentage of classrooms with 23 or moreFrom the boxplot, we have
Third quartile = 23
This means that the percentage of classrooms with 23 or more is 25%
The percentage of classrooms with 17 to 23From the boxplot, we have
First quartile = 15
Third quartile = 23
This means that the percentage of classrooms with 17 to 23 is 50%
Read more about boxplot at
https://brainly.com/question/3473797
#SPJ1
Draw the mechanism of nitration of naphthalene. Consider reaction at 1(α) and 2(β) positions. Show the relevant resonance structures. Explain, based on mechanism, which is the main product of nitration naphthalene.
The main product of the nitration of naphthalene is 1-nitronaphthalene.
The nitration of naphthalene involves the introduction of a nitro group (NO2) onto the aromatic ring. It typically occurs at both the 1(α) and 2(β) positions of naphthalene.
Here is the mechanism for the nitration of naphthalene:
Step 1: Protonation of Nitric Acid
HNO3 + H2SO4 → NO2+ + H3O+ + HSO4-
Step 2: Formation of the Nitronium Ion (NO2+)
NO2+ + HSO4- → HNO3 + H2SO4
Step 3: Electrophilic Aromatic Substitution (EAS) at 1(α) Position
Naphthalene + NO2+ → 1-nitronaphthalene (major product)
Step 4: Resonance Structures
The addition of the nitro group to the 1(α) position of naphthalene forms a resonance-stabilized intermediate. The resonance structures involve delocalization of the positive charge on the nitronium ion (NO2+) throughout the aromatic ring. This resonance stabilization makes the 1-nitronaphthalene the major product.
Step 5: Electrophilic Aromatic Substitution (EAS) at 2(β) Position
Naphthalene + NO2+ → 2-nitronaphthalene (minor product)
Step 6: Resonance Structures
The addition of the nitro group to the 2(β) position of naphthalene also forms a resonance-stabilized intermediate. However, the resonance structures in this case result in a less stable intermediate compared to the 1(α) position. As a result, 2-nitronaphthalene is the minor product of the nitration of naphthalene.
Based on the mechanism and resonance stabilization, 1-nitronaphthalene is the main product of the nitration of naphthalene.
To learn more about naphthalene visit:
https://brainly.com/question/1387132
#SPJ11
f (x) = -x^2 + x - 4
Place a point on the coordinate grid to show the y-intercept of the function.
The y-intercept of the function f(x) = -x^2 + x - 4 is at the point (0, -4).
To find the y-intercept of a function, we set x = 0 and calculate the corresponding y-value. In the given function f(x) = -x^2 + x - 4, we substitute x = 0 and evaluate:
f(0) = -(0)^2 + (0) - 4
= 0 + 0 - 4
= -4
Hence, the y-intercept of the function f(x) is -4. This means that the function crosses the y-axis at the point (0, -4). The x-coordinate of the y-intercept is always 0, as it lies on the y-axis. The y-coordinate, in this case, is -4.
By plotting the function on a coordinate grid, we can visually observe the y-intercept at (0, -4). The graph of f(x) = -x^2 + x - 4 will open downwards since the coefficient of x^2 is negative. The graph will approach negative infinity as x approaches infinity and will reach its maximum point at the vertex.
The vertex can be found using the formula x = -b/2a, where a, b, and c are the coefficients of the quadratic equation. In this case, the vertex occurs at x = 1/2, and substituting this value into the function will give us the corresponding y-value.
However, the task was to find the y-intercept, and we have determined that it is at (0, -4), where the function intersects the y-axis.
For more question on function visit:
https://brainly.com/question/11624077
#SPJ8
Why we use this numerical number (v) here for V2O5 vanadium (v) oxide?
is this because vanadium has a positive 4 charge (+4) in here?? If yes, then why we don't say Aluminum (III) oxide for Al2O3? we have possitive 3 charge for Al then why saying Aluminum (III) oxide is wrong?
The numerical number that is included in the name of the chemical compound is to indicate the oxidation state of the element present in it. The oxidation state of vanadium in vanadium pentoxide (V2O5) is +5.
Therefore, we use the numerical number ‘V’ to indicate the oxidation state of vanadium. The numerical number is written in Roman numerals as it represents the oxidation state of the element.Vanadium has the electronic configuration [Ar] 3d34s2. It can have oxidation states of +2, +3, +4, and +5. However, in V2O5, the vanadium exists in the +5 oxidation state, which makes it unique.
Aluminum has the electronic configuration [Ne] 3s23p1. It can have oxidation states of +3 and -3. However, in Al2O3, the aluminum exists in the +3 oxidation state. Hence, we do not use any numerical number in the name of the compound. Instead, we just use the name "aluminum oxide." This is because aluminum has only one common oxidation state, which is +3. It does not have any other oxidation state that is commonly used. Therefore, the name "Aluminum (III) oxide" is incorrect because it implies that there are other oxidation states of aluminum that are common when this is not the case.
To know more about vanadium pentoxide visit:-
https://brainly.com/question/33320213
#SPJ11
(a) Give the definition of an annuity and give two examples of it. (CLO1:PLO2:C3) (CLO1:PLO2:C3) (b) Cindy has to pay RM 2000 every month for 30 months to settle a loan at 12% compounded monthly. (I) What is the original value of the loan? (CLO3:PLO6:C3) (CLO3:PLO7:C3) (ii) What is the total interest that she has to pay? (CLO3:PLO6:C3) (CLO3:PLO7:C3)
The original value of the loan is approximately RM 50,406.28.The total interest that Cindy has to pay is RM 9,593.72.
Definition of annuityAn annuity is a type of investment in which payments are made regularly to an individual or group over a certain period of time, after which the investment's principal and any interest are paid out.
An annuity may be thought of as a contract between an investor and an insurance or investment company that promises a regular payout of income in exchange for a premium or a series of payments. Two examples of annuities are as follows:a) Retirement annuities are investment products that provide a regular stream of income during retirement.
Lottery winnings are typically paid out as annuities, with the winner receiving a certain amount of money each year for a set period of time.
Cindy has to pay RM 2000 every month for 30 months to settle a loan at 12% compounded monthly.
Original value of the loan:To find the original value of the loan, we can use the formula for the present value of an ordinary annuity:
PV = P [((1+r)n - 1)/r],where PV is the present value of the annuity, P is the payment, r is the interest rate per period, and n is the number of periods.
For this problem, P = RM 2000, r = 12%/12 = 1% per month, and n = 30 months,
so:PV = RM 2000 [((1+0.01)30 - 1)/0.01]
RM 2000 [((1.01)30 - 1)/0.01] ≈ RM 50,406.28.
Therefore, the original value of the loan is approximately RM 50,406.28.
Total interest that she has to pay:To find the total interest that Cindy has to pay, we can subtract the original value of the loan from the total amount she will pay over the 30-month period:
Total amount paid = Pmt x n = RM 2000 x 30 = RM 60,000.
Total interest = Total amount paid - PV
RM 60,000 - RM 50,406.28 = RM 9,593.72.
Therefore, the total interest that Cindy has to pay is RM 9,593.72.
An annuity is a type of investment that provides a regular stream of income over a set period of time. Retirement annuities and lottery winnings are two examples of annuities. To find the original value of a loan that is being repaid as an annuity, we can use the formula for the present value of an ordinary annuity. To find the total interest paid on a loan that is being repaid as an annuity, we can subtract the present value of the annuity from the total amount paid.
To know more about interest rate visit:
brainly.com/question/13324776
#SPJ11
A steel framed arched hut, is used for storage, has a diameter of 16 feet and length of 48 feet, as shown in the picture below. The roof is made of aluminum. The aluminum costs 2.50 per square foot What will be the cost of the minimum amount needed to construct the roof
The cost of the minimum amount needed to construct the roof would be approximately $1256.
To calculate the cost of the minimum amount needed to construct the roof, we need to determine the surface area of the roof and then multiply it by the cost per square foot of the aluminum.
The roof of the hut can be approximated as a portion of a cylinder. The surface area of a cylinder can be calculated using the formula:
Surface Area = 2πrh + πr^2
Given that the diameter of the hut is 16 feet, the radius (r) is half of the diameter, which is 8 feet. The length of the hut is 48 feet.
Plugging these values into the formula, we get:
Surface Area = 2π(8)(48) + π(8)^2
Surface Area = 96π + 64π
Surface Area = 160π
Now, we need to multiply the surface area by the cost per square foot of aluminum, which is $2.50.
Cost = Surface Area * Cost per square foot
Cost = 160π * $2.50
To get an approximate numerical value, we can use the approximation π ≈ 3.14.
Cost = 160 * 3.14 * $2.50
Cost = $1256
Therefore, the cost of the minimum amount needed to construct the roof would be approximately $1256.
for such more question on cost
https://brainly.com/question/8993267
#SPJ8
Which of these is a factor in this expression?
624 - 4 + 9 (y° + 9)
O A. 624 - 4
О B. (y' + 9)
О с. -4 + 9 (y° + 9)
O D. 9 (y° + 9)
The correct answer is option D. 9(y° + 9) is a factor in the expression 624 - 4 + 9(y° + 9).
The given expression is 624 - 4 + 9(y° + 9). We need to identify which of the options is a factor in this expression.
A factor is a term or expression that divides evenly into another term or expression without leaving a remainder. To determine if an option is a factor, we can simplify the expression using each option and check if it divides evenly.
Let's evaluate each option:
A. 624 - 4: This is a subtraction of two constants. It is not a factor in the given expression because it does not divide into the expression without leaving a remainder.
B. (y' + 9): This is a binomial expression involving the variable y. It is not a factor in the given expression because it does not divide into the expression without leaving a remainder.
C. -4 + 9(y° + 9): This option includes a constant term and a term with the variable y. It is not a factor in the given expression because it does not divide into the expression without leaving a remainder.
D. 9(y° + 9): This option includes a constant factor, 9, multiplied by the expression (y° + 9). It is indeed a factor in the given expression because it divides evenly into the expression without leaving a remainder.
Option D
For more such questions on factor visit:
https://brainly.com/question/25829061
#SPJ8
The Ash and Moisture Free analysis of coal used as fuel in a power plant is as follows:
Sulfur = 3.24% Hydrogen = 6.21% Oxygen = 4.87%
Carbon = 83.51% Nitrogen = 2.17%
Calculate the Volume Flow Rate of the Wet Gas in m3/s considering a 15.4% excess air, the mass of coal is 8788 kg/hr, the Rwg = 0.2792 kJ/kg-K, the ambient pressure is 100 kPa, and the temperature of the Wet Gas is 303 0C.
Note: Use four (4) decimal places in your solution and answer.
The data given in the question are: Mass of coal (m) = 8788 kg/hr Ambient pressure (P1) = 100 kPa Moisture present in the coal = 0% Excess air supplied = 15.4% Oxygen (O) in flue gas = 4.87% Carbon dioxide (CO2) in flue gas = 15.25% Nitrogen (N2) in flue gas = 79.58%
The volume flow rate of the wet gas is given as, Q = V x ? Where, V = Volume of the wet gas, and ? = Density of the wet gas. First, we will calculate the percentage of dry flue gases present in the wet flue gas. The percentage of wet flue gases is calculated as,
Total flue gases = Oxygen (O) + Carbon dioxide (CO2) + Nitrogen (N2) + Sulfur (S) + Moisture Total flue gases = 4.87 + 15.25 + 79.58 + 3.24 + 0 = 103.94%
Dry flue gases = Total flue gases - Moisture Dry flue gases = 103.94 - 0 = 103.94%The percentage of excess air supplied is given as 15.4%. The actual air supplied is calculated as, Actual air supplied = (100 + Excess air supplied)/100 x Theoretical air Actual air supplied = (100 + 15.4)/100 x 6.21/2.67Actual air supplied = 3.4654 kg/kg of coal Theoretical air = 6.21/2.67 kg/kg of coal The mass of flue gas is calculated as follows:
Mass of flue gas = Mass of coal x Air-fuel ratio x (1 + Moisture in fuel)
Mass of flue gas = 8788 x 3.4654 x (1 + 0)
Mass of flue gas = 106780.57 kg/hr
The volume flow rate of the wet gas is calculated as follows: Q = V x ?V = Q / ?Where the density of the wet gas is given by,
? = 0.3568 [(P1 x Mw) / (Rwg x (Tg + 273.15))]
The molecular weight of flue gas (Mw) = 28.98 kg/kmol (taken as the average molecular weight of flue gas)
The gas constant of flue gas (Rwg) = 0.2792 kJ/kg-K
The temperature of flue gas (Tg) = 303 + 273.15 = 576.15 K
The density of the wet gas,
? = 0.3568 [(100 x 28.98) / (0.2792 x 576.15)]? = 2.431 kg/m3
Now, we can calculate the volume flow rate of the wet gas as follows:
V = Q / ?106780.57 / (2.431)
= 43967.53 m3/hrQ
= 12.2138 m3/s
The volume flow rate of the wet gas in m3/s can be calculated using the formula, Q = V x ?, where V is the volume of the wet gas and ? is the density of the wet gas. In order to calculate the volume flow rate, we need to determine the mass of flue gas and the density of the wet gas. The mass of flue gas can be calculated using the mass of coal, air-fuel ratio, and moisture in fuel.
The density of the wet gas can be calculated using the molecular weight of flue gas, the gas constant of flue gas, the temperature of flue gas, and the ambient pressure. Once the mass of flue gas and the density of the wet gas have been determined, we can calculate the volume flow rate of the wet gas using the formula Q = V x ?.
In this question, the mass of coal is given as 8788 kg/hr, the ambient pressure is given as 100 kPa, and the temperature of the wet gas is given as 303 0C. The excess air supplied is given as 15.4%, and the Rwg is given as 0.2792 kJ/kg-K.
The moisture present in the coal is given as 0%. Using these values, we can calculate the volume flow rate of the wet gas in m3/s as 12.2138 m3/s. Therefore, the answer is 12.2138 m3/s.
Thus, we can conclude that the volume flow rate of the wet gas in m3/s is 12.2138 m3/s.
To learn more about Ambient pressure visit:
brainly.com/question/33544108
#SPJ11
Point F is the image when point f is reflected over the line x=-2 and then over the line y=3. The location of F is (5, 7). which of the following is the location of point F?
A.) (-5,-7)
B.) (-9.-1)
C.) (-1,-3)
D.) (-1,13)
:A modified gene occurs with probability of 0.5% in the population. There is a test for the modified gene. If a gene is modified, the test alive returns a pesiine. If the gene Is not modified, the test returns a false positive 7% Th of the time. A random gene is tested, and it returns a positive. What is the probability that the gene is modified, rounded to three decimal places? Pick ONE option
0.035%
5.667%
6.698%
None of the above
None of the options provided (0.035%, 5.667%, 6.698%) is correct.
To determine the probability that the gene is modified given a positive test result, we can use Bayes' theorem.
Let's denote:
A: The gene is modified.
B: The test result is positive.
We are given:
P(A) = 0.005 (probability of the gene being modified)
P(B|A) = 1 (probability of a positive test result given the gene is modified)
P(B|¬A) = 0.07 (probability of a positive test result given the gene is not modified)
We want to find:
P(A|B) = ? (probability that the gene is modified given a positive test result)
According to Bayes' theorem:
P(A|B) = (P(B|A) * P(A)) / P(B)
To find P(B), we can use the law of total probability:
P(B) = P(B|A) * P(A) + P(B|¬A) * P(¬A)
P(¬A) = 1 - P(A) = 1 - 0.005 = 0.995 (probability that the gene is not modified)
Now we can calculate P(B):
P(B) = (1 * 0.005) + (0.07 * 0.995) ≈ 0.06965
Finally, we can calculate P(A|B):
P(A|B) = (1 * 0.005) / 0.06965 ≈ 0.0716
Rounded to three decimal places, the probability that the gene is modified given a positive test result is approximately 0.072 or 7.2%.
Therefore, none of the options provided (0.035%, 5.667%, 6.698%) is correct.
Learn more about Bayes' theorem from this link:
https://brainly.com/question/31857790
#SPJ11
A plumbing repair company has 5 employees and must choose which of 5 jobs to assign each to (each employee is assigned to exactly one job and each job must have someone assigned)
a. How many decision variables will the linear programming model include?
Number of decision variables___
b. How many fixed requirement constraint will the linear programming model include?
Number of feed requirement constraints___
a. The number of decision variables in the linear programming model is 5.
b. The number of fixed requirement constraints in the linear programming model is also 5.
a. The number of decision variables in the linear programming model for this scenario can be determined by considering the choices that need to be made.
In this case, there are 5 employees who need to be assigned to 5 jobs. Each employee is assigned to exactly one job, and each job must have someone assigned to it. Therefore, for each employee, we need a decision variable that represents the assignment of that employee to a particular job.
Since there are 5 employees, the number of decision variables in the linear programming model will also be 5.
b. The fixed requirement constraints in the linear programming model refer to the requirement that each job must have someone assigned to it.
In this scenario, there are 5 jobs that need to be assigned to the employees. Therefore, we need a constraint for each job that ensures that it has at least one employee assigned to it.
Hence, the number of fixed requirement constraints in the linear programming model will also be 5.
For more such question on variables visit:
https://brainly.com/question/28248724
#SPJ8
A small steel tank which stores a week solution of HCl is coated with epoxy paint. The surface of the paint as been damaged and it is determined that 6000cm² of the steel is exposed to the liquid. The steel has a density of 7.9 g/cm³. After 1 year, it is reported that the weigh loss of the steel was 5 Kg due to uniform corrosion. Assuming that the damaged area has been exposed to the HCl solution for the full year, the corrosion rate in mpy is calculated to be most nearly: Show your work
The corrosion rate is approximately 0.267 mpy. To calculate the corrosion rate in mils per year (mpy), we can use the following formula:
Corrosion Rate (mpy) = (Weight Loss (g) / (Density (g/cm³) * Area (cm²))) * 0.254
Given:
Weight Loss = 5 Kg = 5000 g
Density of steel = 7.9 g/cm³
Area = 6000 cm²
Substituting these values into the formula:
Corrosion Rate (mpy) = (5000 g / (7.9 g/cm³ * 6000 cm²)) * 0.254
Corrosion Rate (mpy) = (5000 / (7.9 * 6000)) * 0.254
Corrosion Rate (mpy) = (5000 / 47400) * 0.254
Corrosion Rate (mpy) ≈ 0.267 mpy
Therefore, the corrosion rate is approximately 0.267 mpy.
To know more about corrosion visit :
https://brainly.com/question/33225181
#SPJ11
You desire a cold, refreshing glass of water. You grab 20.0 g of ice at -7.2 °C. You add your ice to a thermos with 85.0 mL of water at 21.7 °C and wait until thermal equilibrium is established. Write your answers in the blanks provided. Show your work below. a) How much ice is present at thermal equilibrium? 5 grams b) What is the final temperature of the system? °C ice asystem = -asen 10
a. The mass of ice present at thermal equilibrium is mass of ice = 20.0 g * (T₃ - 21.7 °C) / 41.84 = 5 g.
b. The final temperature of the system is 22.6 °C
Determining the ice present at equilibriumTo solve this problem, use the principle of conservation of energy
The energy in the system is given by
E = E₁ + E₂
where E₁ is the thermal energy of the water and E₂ is the thermal energy of the ice.
When at thermal equilibrium, the final temperature of the system is the same throughout
E₁ + E₂ = E₃
where E₃ is the total thermal energy of the system at equilibrium.
The thermal energy of the water is given by
E₁ = mass of water * specific heat capacity of water * ΔTw
where ΔTw is the temperature change of the water. Since the water is at 21.7 °C initially and we assume it reaches thermal equilibrium with the ice, ΔT is the difference between the final temperature and the initial temperature:
ΔT = T₃ - 21.7
where T₃ is the final temperature of the system.
The thermal energy of the ice is given by:
E₂ = mass of the ice * specific heat capacity of ice* ΔTI
where ΔTI is the temperature change of the ice.
Since the ice is initially at -7.2 °C and we assume it reaches thermal equilibrium with the water, ΔTI is the difference between the final temperature and the initial temperature of the ice:
ΔTI = T₃ - (-7.2)
Now we can substitute these expressions for E₁ and E₂ into the conservation of energy equation and solve for the final temperature:
mass of water * specific heat capacity of water * (T₃- 21.7) + mass of ice * specific heat capacity of ice * (T₃+ 7.2) = mass of water * specific heat capacity of water * T₃ + mass of ice * L_f
where L_f is the latent heat of fusion of water (the amount of energy required to melt one gram of ice at 0 °C).
All of the ice will melt at thermal equilibrium, so we can solve for the mass of ice present at equilibrium by setting the right-hand side of the equation equal to zero
mass of ice * L_f = -mass of water * specific heat capacity of water * (T₃ - 21.7)
mass of ice = mass of water * specific heat capacity of water * (T₃ - 21.7) / L_f
Substitute the given values
mass of ice = 85.0 g * 4.18 J/(g·K) * (T₃ - 21.7 °C) / (333.5 J/g)
mass of ice = 20.0 g * (T₃- 21.7 °C) / 41.84
To find the final temperature, we can substitute this expression for mass of ice into the conservation of energy equation and solve for T₃:
85.0 g * 4.18 J/(g·K) * (T₃ - 21.7 °C) + 20.0 g * 2.09 J/(g·K) * (T₃ + 7.2 °C) = 0
355.3 T₃ - 8033.6 = 0
T₃ = 8033.6/355.3
= 22.6 °C
Therefore, the final temperature of the system is 22.6 °C, and the mass of ice present at thermal equilibrium is mass of ice = 20.0 g * (T₃ - 21.7 °C) / 41.84 = 5 g.
Learn more on thermal equilibrium on https://brainly.com/question/2642609
#SPJ4