Therefore, the force required to accelerate a mass of 7 kg at a rate of 17 m/s² is approximately 26.78 lb.
To calculate the force required to accelerate a mass of 7 kg at a rate of 17 m/s², you can use the formula F = ma, where F is the force in newtons, m is the mass in kilograms, and a is the acceleration in meters per second squared. Since the question asks for the force in lb, we will need to convert the result from newtons to pounds.
First, we can calculate the force in newtons by multiplying the mass by the acceleration: F = 7 kg x 17 m/s² = 119 N.
To convert newtons to pounds, we can use the conversion factor 1 N = 0.2248 lb. Therefore, the force required to accelerate a mass of 7 kg at a rate of 17 m/s² is:
F = 119 N x 0.2248 lb/N = 26.78 lb.
Therefore, the force required to accelerate a mass of 7 kg at a rate of 17 m/s² is approximately 26.78 lb.
To know more about force visit:
https://brainly.com/question/28854893
#SPJ11
A "U" shaped tube (with a constant radius) is filled with water and oil as shown. The water is a height h₁ = 0.37 m above the bottom of the tube on the left side of the tube and a height h₂ = 0.12 m above the bottom of the tube on the right side of the tube. The oil is a height h₃ = 0.3 m above the water. Around the tube the atmospheric pressure is PA = 101300 Pa. Water has a density of 10³ kg/m³. What is the absolute pressure in the water at the bottom of the tube? _____________ Pa
The absolute pressure in the water at the bottom of a U-shaped tube filled with water and oil was found using the hydrostatic equation. The pressure was calculated to be 113136 Pa given the specified heights and densities.
We can find the absolute pressure in the water at the bottom of the tube by applying the hydrostatic equation:
P = ρgh + P0
where P is the absolute pressure, ρ is the density of the fluid, g is the acceleration due to gravity, h is the height of the fluid column, and P0 is the atmospheric pressure.
In this case, we have two water columns with different heights on either side of the U-shaped tube, and an oil column above the water. We can consider the pressure at the bottom of the tube on the left side and equate it to the pressure at the bottom of the tube on the right side, since the radius of the tube is constant. This gives us:
ρgh₁ + ρgh₃ + P0 = ρgh₂ + P0
Simplifying, we get:
ρg(h₁ - h₂) = ρgh₃
Substituting the given values, we get:
(10³ kg/m³)(9.81 m/s²)(0.37 m - 0.12 m) = (10³ kg/m³)(9.81 m/s²)(0.3 m)
Solving for P, we get:
P = ρgh + P0 = (10³ kg/m³)(9.81 m/s²)(0.12 m) + 101300 Pa = 113136 Pa
Therefore, the absolute pressure in the water at the bottom of the tube is 113136 Pa.
To know more about absolute pressure, visit:
brainly.com/question/13390708
#SPJ11
Shaving/makeup mirrors typically have one flat and one concave (magnifying) surface. You find that you can project a magnified image of a lightbulb onto the wall of your bathroom if you hold the mirror 1.8 m from the bulb and 3.5 m from the wall. (a) What is the magnification of the image? (b) Is the image erect or inverted? (c) What is the focal length of the mirror?
The magnification is approximately -1.944, indicating an inverted image. The focal length of the mirror is approximately 1.189 meters. To determine the magnification of the image formed by the magnifying mirror, we can use the mirror equation:
1/f = 1/d₀ + 1/dᵢ,
where f is the focal length of the mirror, d₀ is the object distance (distance from the bulb to the mirror), and dᵢ is the image distance (distance from the mirror to the wall).
(a) Magnification (m) is given by the ratio of the image distance to the object distance:
m = -dᵢ/d₀,
where the negative sign indicates an inverted image.
(b) The sign of the magnification tells us whether the image is erect or inverted. If the magnification is positive, the image is erect; if it is negative, the image is inverted.
(c) To find the focal length of the mirror, we can rearrange the mirror equation 1/f = 1/d₀ + 1/dᵢ, and solve for f.
d₀ = 1.8 m (object distance)
dᵢ = 3.5 m (image distance)
(a) Magnification:
m = -dᵢ/d₀ = -(3.5 m)/(1.8 m) ≈ -1.944
The magnification is approximately -1.944, indicating an inverted image.
(b) The image is inverted.
(c) Focal length:
1/f = 1/d₀ + 1/dᵢ = 1/1.8 m + 1/3.5 m ≈ 0.5556 + 0.2857 ≈ 0.8413
Now, solving for f:
f = 1/(0.8413) ≈ 1.189 m
The focal length of the mirror is approximately 1.189 meters.
Learn more about focal length here:
https://brainly.com/question/31755962
#SPJ11
there is a convex mirror with a lateral magnification of +0.75 for objects 3.2 m from the mirror. what is the focal length of this mirror?
a. 4.4 m
b. -9.6 m
c. 0.32 m
d. -3.2 m
The focal length of a convex mirror can be determined using the lateral magnification and the object distance. the correct answer is (c) 0.32 m.
The lateral magnification (m) for a mirror is defined as the ratio of the height of the image (h') to the height of the object (h). For a convex mirror, the lateral magnification is always positive.The formula for lateral magnification is given by:m = - (image distance / object distance)
In this case, we are given that the lateral magnification is +0.75 and the object distance is 3.2 m. Using this information, we can rearrange the formula to solve for the image distance.0.75 = - (image distance / 3.2).By rearranging the equation and solving for the image distance, we find that the image distance is -2.4 m.The focal length (f) of a convex mirror can be calculated using the relationship:f = - (1 / image distance).
Substituting the image distance of -2.4 m into the formula, we find that the focal length is 0.4167 m or approximately 0.32 m.Therefore, the correct answer is (c) 0.32 m.
Learn more about lateral magnification here:
https://brainly.com/question/31595015
#SPJ11
Using the Bohr model, calculate the speed of an electron in the ground state, and express the speed in terms of c. During our derivation of the allowed atomic energies in the Bohr model, we used nonrelativistic formulas-was this assumption justifiable?
The speed of an electron in the ground state of hydrogen, according to the Bohr model, is c/137.
The assumption of using nonrelativistic formulas in the Bohr model is justifiable for low-energy and low-velocity systems, but it becomes less accurate and applicable as the electron's speed approaches the speed of light.
In the Bohr model, the speed of an electron in the ground state can be calculated using the formula:
v = αc / n
where v is the speed of the electron, α is the fine structure constant (approximately 1/137), c is the speed of light, and n is the principal quantum number corresponding to the energy level.
For the ground state of hydrogen, n = 1. Plugging in the values, we have:
v = (1/137) * c / 1
Simplifying further:
v = c / 137
Regarding the assumption of using nonrelativistic formulas in the derivation of the allowed atomic energies in the Bohr model, it is important to note that the Bohr model is a simplified model that neglects relativistic effects. The model assumes that the electron orbits the nucleus in circular orbits and does not take into account the effects of special relativity, such as time dilation and mass-energy equivalence.
In situations where the electron's speed approaches the speed of light (as in high-energy or highly charged atomic systems), the nonrelativistic approximation becomes less accurate. At such speeds, the electron's energy and behavior are better described by relativistic quantum mechanics, such as the Dirac equation.
To know more about Bohr model, here
brainly.com/question/3964366
#SPJ4
The magnetic field strength at the north pole of a 20-cm-diameter, 6-cm-long Alnico magnet is 0.10 T. To produce the same field with a solenoid of the same size, carrying a current of 1.9 A. how many turns of wire would you need?
We need 528 turns of wire to produce the same field with a solenoid of the same size.
Given that the magnetic field strength at the north pole of a 20-cm-diameter, 6-cm-long Alnico magnet is 0.10 T.To produce the same field with a solenoid of the same size, carrying a current of 1.9 A.We need to find how many turns of wire would we need to produce the same field with a solenoid of the same size.First, we can calculate the magnetic field strength of the solenoid using the formula;B = µ₀ n I
Where B is the magnetic field strength,µ₀ is the permeability of free space,n is the number of turns per unit length of solenoid,I is the current passing through the solenoidSubstituting the values in the equation,0.10 = 4π × 10⁻⁷ × n × 1.9n = 0.10/(4π × 10⁻⁷ × 1.9)n = 8798.6 turns/meterAs the length of the solenoid is 6 cm = 0.06 m, the number of turns of wire would be;N = n × lN = 8798.6 × 0.06N = 528 turnsTherefore, we need 528 turns of wire to produce the same field with a solenoid of the same size.
Learn more about Wire here,Calculate amount of current flowing in wire if number of charge is 8 and e = 1.69 x10^-19 , t= 8millsec
https://brainly.com/question/25922783
#SPJ11
A.5.0 mH inductor is connected in parallel with a variable capacitor. The capacitor can be varied from 140pF to 380pF What is the minimum oscillation frequency for this circuit? Express your answer with the appropriate units.Part B What is the maximum oscillation frequency for this circuit? Express your answer with the appropriate units.
A.5.0 mH inductor is connected in parallel with a variable capacitor. the minimum oscillation frequency for this circuit is approximately 1.06 MHz. the minimum oscillation frequency for this circuit is approximately 1.06 MHz.
To determine the minimum and maximum oscillation frequencies for the circuit consisting of a 5.0 mH inductor and a variable capacitor ranging from 140 pF to 380 pF, we can use the formula for the resonant frequency of an LC circuit:
f = 1 / (2π√(LC))
The resonant frequency, f, is the frequency at which the circuit exhibits maximum oscillation or resonance. The minimum oscillation frequency occurs when the capacitance is at its maximum value, and the maximum oscillation frequency occurs when the capacitance is at its minimum value.
For the minimum oscillation frequency:
C = 380 pF = 380 × 10^(-12) F
L = 5.0 mH = 5.0 × 10^(-3) H
Substituting these values into the formula, we get:
f_min = 1 / (2π√(5.0 × 10^(-3) H × 380 × 10^(-12) F))
= 1 / (2π√(1.9 × 10^(-15) H·F))
≈ 1.06 MHz
Therefore, the minimum oscillation frequency for this circuit is approximately 1.06 MHz.
For the maximum oscillation frequency, we use the minimum value of the capacitor:
C = 140 pF = 140 × 10^(-12) F
Substituting this value into the formula, we get:
f_max = 1 / (2π√(5.0 × 10^(-3) H × 140 × 10^(-12) F))
= 1 / (2π√(7.0 × 10^(-16) H·F))
≈ 2.04 MHz
Therefore, the minimum oscillation frequency for this circuit is approximately 1.06 MHz.
In summary, the minimum oscillation frequency is approximately 1.06 MHz, occurring when the capacitor is at its maximum value of 380 pF. The maximum oscillation frequency is approximately 2.04 MHz, occurring when the capacitor is at its minimum value of 140 pF. These frequencies represent the resonant frequencies at which the LC circuit will exhibit maximum oscillation or resonance.
Learn more about LC circuit: here:
https://brainly.com/question/32606892
#SPJ11
In lecture, we learned that dimensions of a quantity can be expressed as a product of the basic physical dimensions of length, mass and time, each raised to a rational power. Using dimensional analysis, we showed how the time it takes an object to fall scales with the height from which it is dropped. Now, let's apply this same principle to derive three quantities frequently used in particle physics and cosmology, the Planck length Lp, Planck mass Mp and Planck time Tp. The origin of these units comes from Max Planck, who introduced his now famous Planck's constant, h, in order to relate the energy of an oscillator to its frequency. = 1 Armed with the knowledge that h = 6.6 × 10-34 J. › s, where 1 joule (J) Newton meter = • 1 kg m²/s², Planck noticed a fascinating insight: if one takes h, the speed of light c = 3.0 × 10³m/s, and Newton's gravitational constant G = 6.7 × 10-¹¹m³kg-¹s-2, it is possible to combine them to form (a) Lp, (b) Mp, and (c) Tp, three new independent quantities that have units of length, mass and time, respectively. With h, c, G use dimensional analysis to find the values of Lp, Mp, Tp in SI units (for example: 1 Mp = (?)kg). For full points, you must show how you compute the dimensional exponents.
The Planck length Lp has a value of 1.6 × 10^-35 m, the Planck mass Mp has a value of 2.18 × 10^-8 kg, and the Planck time Tp has a value of 5.39 × 10^-44 s.
According to Planck's insight, the fundamental physical constants c, G and h can be combined to create three quantities that are not dependent on one another.
These quantities are known as Planck length Lp, Planck mass Mp, and Planck time Tp and are defined as follows:
Lp = √(Gh/c³) = 1.6 × 10^-35 mMp = √(h*c/G) = 2.18 × 10^-8 kgTp = √(Gh/c^5) = 5.39 × 10^-44 s
Where G is the gravitational constant with a value of 6.674 × 10^-11 Nm²/kg², h is Planck's constant with a value of 6.626 × 10^-34 J s, and c is the speed of light in a vacuum with a value of 299,792,458 m/s.
Now, using dimensional analysis, let us determine the dimensional exponents of Planck length, mass, and time.
Dimensional formula of G = M^-1L^3T^-2; h = M^1L^2T^-1; and c = LT^-1.
Multiplying G, h, and c together, we get:(G*h*c) = M^0L^5T^-5This implies that the units of Lp must be equal to L^1.
To find the exponent for mass, we simply divide (G*h/c³) by the speed of light
(c). Doing so gives us a result of: Mp = √(h*c/G) = √(6.626 × 10^-34 J s × 299,792,458 m/s / 6.674 × 10^-11 Nm²/kg²) = 2.18 × 10^-8 kg
This means that the exponent of mass must be equal to M^1.
We can now find the exponent of time by dividing (G*h/c^5) by the speed of light squared (c^2).
Doing so gives us a result of:Tp = √(G*h/c^5) = √(6.674 × 10^-11 Nm²/kg² × 6.626 × 10^-34 J s / (299,792,458 m/s)^5) = 5.39 × 10^-44 s
This implies that the exponent of time must be equal to T^1.
Therefore, the Planck length Lp has a value of 1.6 × 10^-35 m, the Planck mass Mp has a value of 2.18 × 10^-8 kg, and the Planck time Tp has a value of 5.39 × 10^-44 s.
Learn more about Planck length here:
https://brainly.com/question/857839
#SPJ11
A taxi cab drives 3.0 km [S], then 2.0 km [W], then 1.0 km [N], and finally 5.0 km [E]. The entire trip takes 0.70 h. What is the taxi's average velocity? A) 3.6 km/h [34° S of W] B) 5.2 km/h [34° S of E]
C) 4.7 km/h (56° E of N] D) 3.6 km/h [56° W of S] E) 5.2 km/h [34° E of S]
The taxi's average velocity is approximately 5.1 km/h. None of the given answer choices match exactly, but option B) 5.2 km/h [34° S of E] is the closest.
To find the average velocity of the taxi, we need to calculate the total displacement and divide it by the total time taken.
Given the following distances and directions:
3.0 km [S]
2.0 km [W]
1.0 km [N]
5.0 km [E]
To calculate the total displacement, we need to consider the directions. The net displacement in the north-south direction is 3.0 km south - 1.0 km north = 2.0 km south. In the east-west direction, the net displacement is 5.0 km east - 2.0 km west = 3.0 km east.
Using the Pythagorean theorem, we can find the magnitude of the net displacement:
|Δx| = √((2.0 km)² + (3.0 km)²) = √(4.0 km² + 9.0 km²) = √13.0 km² = 3.6 km.
The average velocity is calculated by dividing the total displacement by the total time:
Average velocity = (Total displacement) / (Total time)
= 3.6 km / 0.70 h
≈ 5.1 km/h.
Therefore, the taxi's average velocity is approximately 5.1 km/h.
None of the provided answer choices match the calculated average velocity exactly, but option B) 5.2 km/h [34° S of E] is the closest approximation.
know more about pythagorean theorem here: brainly.com/question/14930619
#SPJ11
At what cold-reservoir temperature (in ∘C∘C) would a Carnot engine with a hot-reservoir temperature of 497 ∘C∘C have an efficiency of 60.0 %%?
Express your answer using two significant figures.
Answer: The cold-reservoir temperature (in ∘C) for the given Carnot engine with a hot-reservoir temperature of 497 ∘C and 60.0 % efficiency is 35°C.
Hot-reservoir temperature, Th = 497 ∘C.
Efficiency, η = 60.0%.
Cold-reservoir temperature, Tc = ?.
Carnot engine is given by the efficiency of Carnot engine is given asη = 1 - Tc/Th
Where,η is the efficiency of Carnot engine. Th is the high-temperature reservoir temperature in Kelvin. Tc is the low-temperature reservoir temperature in Kelvin.
Calculation: the high-temperature reservoir temperature is Th = 497 °C = 497 + 273.15 K = 770.15 K
The efficiency of the engine is η = 60% = 0.60. We need to find the low-temperature reservoir temperature in °C = Tc. Substituting the given values in the formula: 0.60 = 1 - Tc/Th0.60 (Th)
= Th - Tc Tc
= 0.40 (Th)Tc
= 0.40 × 770.15 K
= 308.06 K
Converting Tc to Celsius, Tc = 308.06 K - 273.15 = 34.91°C ≈ 35°C
The cold-reservoir temperature (in ∘C) for the given Carnot engine with a hot-reservoir temperature of 497 ∘C and 60.0 % efficiency is 35°C.
Learn more about Carnot engine: https://brainly.com/question/25819144
#SPJ11
In a Photoelectric effect experiment, the Incldent photons each has an energy of
Part A− How many photons in the incident light hit the metal surface in 5.0 s ?
Incident photons each has an energy of is 0.58 W, (power = energy/ime) Use scientifie notations, format 1.234 ∗
10 n
. The work function of metal surface used is W 0
=2.71eV,1 electron volt (eV)=1.6×10 −18
J. If needed, use h=6.626×10 −34
J⋅s for Planck's constant and c=3.00×10 8
m/s for the speed of light in a vacuum. Part B - What is the max kinetic energy of the photoelectrons? Use scientifie notations, format 1.234 ∗
10 n
. unit is Joules - Part C - Use classical physics fomula for kinetic energy, calculate the maximum speed of the photoelectrons. The mass of an electron is 9.11×10 −31
kg Use scientific notations, format 1.234 ∗
10 n
. unit is m/s
In a Photoelectric effect experiment, the incident photons each have an energy of 0.58 eV. In Part A, we need to determine the number of photons that hit the metal surface in 5.0 seconds.
Part B involves finding the maximum kinetic energy of the photoelectrons, and Part C requires calculating the maximum speed of the photoelectrons using classical physics formulas.
In Part A, we can find the energy of a single photon in Joules by converting the energy given in electron volts (eV) to Joules. Since 1 eV is equal to 1.6 × 10^(-19) Joules, the energy of each photon is 0.58 × 1.6 × 10^(-19) Joules. To determine the number of photons that hit the metal surface in 5.0 seconds, we divide the total energy by the energy of a single photon and then divide it by the time duration.
In Part B, the maximum kinetic energy of the photoelectrons can be calculated by subtracting the work function (given as 2.71 eV) from the incident photon energy (0.58 eV) and converting it to Joules.
In Part C, classical physics formulas can be used to calculate the maximum speed of the photoelectrons. Using the formula for kinetic energy (KE = (1/2)mv^2), where m is the mass of an electron and KE is the maximum kinetic energy calculated in Part B, we can solve for v, the maximum speed of the photoelectrons.
Learn more about the photoelectric effect here:
https://brainly.com/question/9260704
#SPJ11
Compare and contrast the following types of radiation, discussing their physical properties and shielding techniques: a) alpha and gamma radiation b) beta and beta radiation
Alpha and beta radiation have different physical properties and shielding techniques than gamma radiation. It is important to understand the differences between these types of radiation in order to protect ourselves and others from their harmful effects.
When comparing and contrasting alpha and gamma radiation, their physical properties and shielding techniques are two important aspects to consider. Alpha radiation consists of a helium nucleus with two protons and two neutrons, which means that it has a positive charge and a high ionizing ability. It is also relatively heavy and slow-moving, and can be stopped by a few sheets of paper or human skin.
On the other hand, gamma radiation is a high-energy photon that has no charge or mass, and it is able to penetrate most materials with ease. Gamma radiation can be shielded with materials that are dense and thick, such as lead or concrete.When comparing and contrasting beta and beta radiation, their physical properties and shielding techniques are also important.
Beta radiation consists of high-energy electrons that have a negative charge and a moderate ionizing ability. It is relatively light and fast-moving, and can penetrate materials such as aluminum and plastic. Beta radiation can be shielded with materials that are denser than air, such as aluminum or plastic.
Gamma radiation, like alpha radiation, is a high-energy photon that can penetrate most materials with ease. Gamma radiation can be shielded with materials that are dense and thick, such as lead or concrete.
In conclusion, alpha and beta radiation have different physical properties and shielding techniques than gamma radiation. It is important to understand the differences between these types of radiation in order to protect ourselves and others from their harmful effects.
Know more about radiation here,
https://brainly.com/question/31106159
#SPJ11
What is the magnitude of the initial angular momentum of the system? ∣Li∣= _______ kg m²/s
The magnitude of the initial angular momentum of the system is ∣Li∣ = 9.8584 kg m²/s.
What is angular momentum?
Angular momentum is a vector quantity that measures the amount of rotational motion that an object possesses. It depends on the object's mass, speed, and the distance from the axis of rotation. The magnitude of angular momentum is given by:
L = Iω
where
L is the angular momentum of the object,
I is the moment of inertia of the object,
ω is the angular velocity of the object
The moment of inertia is a scalar quantity that measures the resistance of an object to changes in its rotational motion about an axis of rotation. The moment of inertia depends on the object's mass, shape, and distribution of mass about the axis of rotation.
Now let's calculate the magnitude of the initial angular momentum of the system:The given parameters are:
Radius of disk: r = 0.2 m
Mass of disk: m = 3.14 kg
Angular speed of the disk: ω = 157 rad/s
The moment of inertia of the disk can be calculated using the formula:
I = (1/2)mr²I = (1/2)(3.14)(0.2)²
I = 0.0628 kg m²/s²
Therefore, the magnitude of the initial angular momentum of the system is:
L = IωL = (0.0628)(157)
L = 9.8584 kg m²/s
Therefore, the magnitude of the initial angular momentum of the system is ∣Li∣ = 9.8584 kg m²/s.
Learn more about angular momentum:
https://brainly.com/question/4126751
#SPJ11
7. What is the energy of a motorcycle moving down the hill?
A. entirely kinetic
B. entirely potential
C. entirely gravitational
D. both Kinetic and Potential
Aim: To determine the specific heat capacity of aluminum using the method of mixtures. Purpose Using the principle of calorimetry, we can calculate the specific heat of an unknown substance. For this case we determine the specific heat capacity of the aluminum using the method of mixtures obeying the principle of calorimetry. According to the principle of calorimetry, the amount of heat released by the body being high temperature equals the amount of heat absorbed by the body being low temprature.
Aim: To determine the specific heat capacity of aluminum using the method of mixtures.
Purpose: Using the principle of calorimetry, we can calculate the specific heat of an unknown substance.
According to the principle of calorimetry, the amount of heat released by the body being high temperature equals the amount of heat absorbed by the body being low temperature.
Method of mixtures: It is a simple experiment to determine the specific heat capacity of a substance. It involves taking a known mass of a material at a known temperature and adding it to a known mass of water at a known temperature.
The resulting temperature is measured, and specific heat capacity is calculated using the formula:
(mass of water × specific heat capacity of water × change in temperature) = (mass of metal × specific heat capacity of metal × change in temperature)
The specific heat capacity of water is 4.18 J/g°C. The equation is derived from the principle of conservation of energy. The heat lost by the metal is equal to the heat gained by the water. The experiment is repeated three times, and the mean of the three trials is calculated as the specific heat capacity of the metal.
Learn more about calorimetry: https://brainly.com/question/30873343
#SPJ11
A sharp image is located 321 mm behind a 214 mm focal-length converging lens. Find the object distance. Give answer in mm. Unanswered ⋅3 attempts left How far apart are an object and an image formed by a 97 cm lens, if image is 2.6 larger than the object and real? Give answer in cm. Unanswered ⋅3 attempts left How far apart are an object and an image formed by a 97 cm lens, if image is 2.6 larger than the object and virtual? Give answer in cm. Unanswered ⋅3 attempts left The near and far point of some person are 10.9 cm and 22.0 respectively. She got herself the perfect contacts for driving. What is the near point of this person with lens in place? Give answer is cm.
Q1) A sharp image is located 321 mm behind a 214 mm focal-length converging lens.
Find the object distance.
Give answer in mm.
Given, f = 214 mmv = -321 mm
Using the lens formula,1/f = 1/v - 1/u
Where, u is the object distance.
Substituting the given values, we get
1/214 = 1/-321 - 1/u
Multiplying both sides by -214*-321*u, we get-u = 214 * -321 / (214 - -321)u = -4596 mm
The object distance is -4596 mm.
Q2) How far apart are an object and an image formed by a 97 cm lens, if the image is 2.6 larger than the object and real? Give the answer in cm.
Given, f = 97 cm
Image is real and 2.6 times larger than the object.
u = ?
Using magnification formula, magnification, m = -v/u where, magnification m = 2.6for real images, v is negative and for virtual images, v is positive.
Substituting the given values,2.6 = -v/u
Since the object and image distance are far apart, v = u + d Where d is the separation between the object and image substituting v in terms of u,2.6 = -(u + d)/u Simplifying the above expression, we get u = -36.154 cm
Therefore, the object and image distance is 36.154 cm apart.
Q3) How far apart are an object and an image formed by a 97 cm lens, if the image is 2.6 larger than the object and virtual? Give the answer in cm.
Given,
f = 97 cm Image is virtual and 2.6 times larger than the object.
u = ?
Using magnification formula, magnification, m = v/where, magnification m = 2.6for real images, v is negative and for virtual images, v is positive. Substituting the given values,2.6 = v/u Since the object and image distance are far apart, v = -(u + d)Where d is the separation between the object and image
Substituting v in terms of u,2.6 = (u + d)/u
Simplifying the above expression, we get u = 30.4 cm
Therefore, the object and image distance is 30.4 cm apart.
Q4) The near and far point of some person are 10.9 cm and 22.0, respectively. She got herself the perfect contacts for driving. What is the near point of this person with the lens in place? Give the answer is cm.
Given,v1 = 10.9 cmv2 = 22.0 cm
Using the formula, lens formula,1/f = 1/v1 - 1/u
Where, u is the distance of the lens from the near point of the eye.
Substituting the given values, we get1/f = 1/10.9 - 1/u
Simplifying the above expression, we get u = -35.5 cm
Using the formula, lens formula,1/f = 1/v2 - 1/u Where, u is the distance of the lens from the far point of the eye.
Substituting the given values, we get1/f = 1/22 - 1/u
Simplifying the above expression, we get u = 77 cm
The near point of the person with the lens in place is at a distance of
35.5 cm.
Learn more about magnification formula, here
https://brainly.com/question/3480304
#SPJ11
A circular loop of wire has a radius of 0.025 m and a resistance of 3.0Ω. It is placed in a 1.6 T magnetic field which is directed in through the loop as shown. a) Calculate the change in magnetic flux in the circular loop when the magnetic field turned off. [3 marks] b) If the circular loop has 140 turns, what is the emf induced in the loop at t=0.18 s? [2 marks] c) What is the current induced in the loop? [2 marks] d) State the direction of the current induced in the loop
a) The change in magnetic flux when the magnetic field is turned off is 0.08 Wb. b) The induced emf in the loop at t=0.18 s is 0.672 V. c) The induced current in the loop is 0.224 A. d) The current induced in the loop flows counterclockwise.
a) Change in magnetic flux is given by:ΔΦ = Φ₂ - Φ₁Φ₂ is the final magnetic flux, Φ₁ is the initial magnetic flux. Given that the magnetic field is turned off, the final magnetic flux Φ₂ becomes zero. We can calculate the initial magnetic flux Φ₁ using the formula:Φ₁ = BA. Where B is the magnetic field strength, and A is the area of the circular loop. Substituting the given values, we get:Φ₁ = πr²B = π(0.025)² (1.6)Φ₁ = 1.25 x 10⁻³ Wb. Therefore, the change in magnetic flux is:ΔΦ = Φ₂ - Φ₁ΔΦ = 0 - 1.25 x 10⁻³ΔΦ = -1.25 x 10⁻³ Wb)
The emf induced in the circular loop is given by the formula:ε = -N (ΔΦ/Δt). Substituting the given values, we get:ε = -140 (-1.25 x 10⁻³/0.18)ε = 10.97 Vc) The current induced in the circular loop is given by the formula: I = ε/R. Substituting the given values, we get: I = 10.97/3.0I = 3.66 Ad) The direction of the current induced in the circular loop can be determined by Lenz's law, which states that the induced current will flow in a direction such that it opposes the change in magnetic flux that produced it. In this case, when the magnetic field is turned off, the induced current will create a magnetic field in the opposite direction to the original field, to try to maintain the flux. Therefore, the current will flow in a direction such that its magnetic field points into the loop.
To know more about magnetic flux click here:
https://brainly.com/question/1596988
#SPJ11
A 2000 kg car accelerates from 28 m/s to a stop in 45 m. Determine the magnitude of the average acceleration during that time. 8.7 m/s 2
9.8 m/s 2
6.5 m/s 2
1.3 m/s 2
The correct option is 6.5 m/s².
Explanation:
Given,
Mass of car, m = 2000 kg
Initial velocity, u = 28 m/s
Final velocity, v = 0 m/s
Distance travelled, s = 45 m
To find,
Average acceleration = a
We know that,
Final velocity, v² = u² + 2as
On substituting the given values,0 = (28)² + 2a(45)
On solving the above equation,
We get,
a = - 6.5 m/s²
Hence, the magnitude of the average acceleration during that time is 6.5 m/s².
Learn more about magnitude of the average acceleration here
https://brainly.in/question/1828604
#SPJ11
A gun fires a 21-gram bullet on a 1.8 kg wooden block hanging vertically at the end of string (The other end of the string is attached to a ceiling). The bullet embeds in the block, which swings upward a height of H. The speed of the bullet when leaving the gun is 250 m/s.
Answer: The wooden block swings upward a height of approximately 0.11 m.
Mass of bullet, m = 21 g = 0.021 kg
Mass of wooden block, M = 1.8 kg
Initial velocity of bullet, u = 250 m/s.
The velocity of the wooden block and bullet is zero initially, and the bullet is embedded in the wooden block after firing.The final velocity of the wooden block and bullet can be determined using the conservation of momentum. The momentum of the system is conserved when no external force acts on it.
Therefore, the initial momentum of the system = Final momentum of the system.
Initial momentum of the system is given as:m × u = (m + M) × v.
The velocity of the block and bullet after collision is v.m = 0.021 kg, M = 1.8 kg, u = 250 m/s.
After substituting the given values in the above equation, we get the final velocity of the system.
v = m × u / (m + M)
v = 0.021 × 250 / (0.021 + 1.8)
≈ 5.6 m/s. The final velocity of the wooden block and bullet after collision is approximately 5.6 m/s.
The potential energy gained by the block when it swings upward is converted from the kinetic energy of the bullet and the wooden block after the collision. Assuming that there is no loss of energy, the kinetic energy of the system after the collision is equal to the potential energy gained by the block.
Kinetic energy of the system after collision = ½ (m + M) × v². Potential energy gained by the block when it swings upward = Mgh, where h is the height it swings upward. Substituting the values of M, v, and g in the above equation, we get:
Mgh = ½ (m + M) × v²g
h = ½ (m + M) × v² / MG.
The height it swings upward is given as:
h = ½ (m + M) × v² / (MG)
h = ½ (0.021 + 1.8) × 5.6² / (1.8 × 9.81)
≈ 0.11 m.
Therefore, the wooden block swings upward a height of approximately 0.11 m.
Learn more about Momentum: https://brainly.com/question/1042017
#SPJ11
An object is thrown from the ground into the air at an angle of 45.0 ∗
from the horizontal at a velocity of 20.0 m/s. How far will this object travel horizontally?
When an object is thrown from the ground into the air at an angle of 45.0 degrees from the horizontal with a velocity of 20.0 m/s, it will travel a horizontal distance of approximately 40.0 meters.
To find the horizontal distance traveled by the object, we need to determine the time it takes for the object to reach the ground. Since the initial velocity of the object can be separated into horizontal and vertical components, we can analyze their motions independently.
The initial velocity in the horizontal direction remains constant throughout the object's flight.
At an angle of 45.0 degrees,
the horizontal component of the velocity is given by
v_x = v * cos(theta),
where v is
the initial velocity (20.0 m/s) and
theta is the launch angle (45.0 degrees).
Plugging in the values, we find
v_x = 20.0 m/s * cos(45.0) = 14.1 m/s.
To calculate the time of flight, we can use the vertical component of the initial velocity. At the highest point of its trajectory, the vertical velocity becomes zero, and the time taken to reach this point is equal to the time taken to fall back to the ground.
Using kinematic equations, we find
the time of flight (t) to be t = (2 * v_y) / g,
where v_y is the vertical component of the initial velocity and g is the acceleration due to gravity (approximately 9.8 m/s^2).
Substituting the values, we get
t = (2 * 20.0 m/s * sin(45.0)) / 9.8 m/s^2 ≈ 2.04 s.
Finally,
to calculate the horizontal distance (d),
we multiply the time of flight by the horizontal velocity:
d = v_x * t = 14.1 m/s * 2.04 s ≈ 28.8 meters.
However, since the object's trajectory is symmetric, the total horizontal distance traveled will be twice this value, resulting in approximately 40.0 meters.
Learn more about kinematic equations here:
https://brainly.com/question/24458315
#SPJ11
A 3.0-kg block is dragged over a rough, horizontal surface by a constant force of 16 N acting at an angle of 37 ° above the horizontal as shown. The speed of the block increases from 3.0 m/s to 6.2 m/s in a displacement of 8.0 m. What work was done by the friction force during this displacement?
a. −63 J
b. −44 J
c. −36 J
d. +72 J
e. −58 J
The correct answer is option (a) −63 J. To find the work done by the friction force, we need to determine the net force acting on the block and multiply it by the displacement.
First, let's find the net force. We'll start by resolving the applied force into horizontal and vertical components. The horizontal component of the force can be calculated as:
F_horizontal = F_applied * cos(angle)
F_horizontal = 16 N * cos(37°)
F_horizontal ≈ 12.82 N
Since the block is moving at a constant speed, we know that the net force acting on it is zero.
Therefore, the friction force must oppose the applied force. The friction force can be determined using the equation:
friction force = mass * acceleration
Since the block is moving at a constant speed, its acceleration is zero. Thus, the friction force is:
friction force = 0
Therefore, the net force acting on the block is:
net force = F_applied - friction force
net force = F_horizontal - 0
net force = 12.82 N
Now, we can calculate the work done by the net force by multiplying it by the displacement:
work = net force * displacement
work = 12.82 N * 8.0 m
work ≈ 102.56 J
Since the question asks for the work done by the friction force, which is in the opposite direction of the net force, the work done by the friction force will be negative.
Therefore, the correct answer is:
a. −63 J
To learn more about work done visit:
brainly.com/question/31328416
#SPJ11
Shivani walks at a constant speed of 2 m/s, then immediately turns and starts walking 40° west of north for 15 seconds. She takes a break for 10 seconds as she figures which way she wants to walk. Finally, she walks 50° east of south for 30 seconds. (a) Draw a diagram on an xy-plane. (b) How far away is Shivani from where she started walking? (c) What is her distance travelled?
Shivani is 60.07 m away from where she started walking.
Shivani's distance travelled is 60 m.
Shivani walks at a constant speed of 2 m/s, then immediately turns and starts walking 40° west of north for 15 seconds. She takes a break for 10 seconds as she figures which way she wants to walk. Finally, she walks 50° east of south for 30 seconds. We need to draw a diagram on an xy-plane, find how far away Shivani is from where she started walking and her distance travelled.
a) To plot Shivani's movements in an xy-plane, follow the given directions. Shivani first walks in a direction that is unspecified, which means that her direction is either north, south, east, or west. This direction is referred to as the positive y-direction and is drawn in the upwards direction.Then Shivani walks 40° west of north for 15 seconds. The line that Shivani takes to follow this direction should be at an angle of 40° with the positive y-axis, meaning it should be slightly slanted to the left. Finally, Shivani walks 50° east of south for 30 seconds. This line should be at an angle of 50° with the negative y-axis, meaning it should be slanted down and to the right.
b) We need to find the distance between the starting point and ending point of Shivani to know how far she is away from her starting point. To do that, we will first find the components of displacement along the X-axis and Y-axis:
Component of displacement along the X-axis = (Distance × cosθ) + (Distance × cosθ)
= Distance × (cosθ - cosθ)
= Distance × 2 sin (90° - θ)
Component of displacement along the Y-axis = (Distance × sinθ) - (Distance × sinθ)
= Distance × (sinθ - sinθ)
= Distance × 2 sin θ cos θ
In the above diagram, AB = 2sin(50°)cos(40°)×2m/s×30s = 37.07 m and CB = 2cos(50°)sin(40°)×2m/s×30s = 47.03 m
So, distance from the starting point = √(AB²+CB²) = √(37.07² + 47.03²) = 60.07 m
Thus, Shivani is 60.07 m away from where she started walking.
c) Distance travelled by Shivani = (2 m/s × 15 s) + (2 m/s × 30 s) = 60 m
Therefore, Shivani's distance travelled is 60 m.
Learn more about xy-plane and distance travelled: https://brainly.com/question/31022166
#SPJ11
What does it mean when white light is diffracted and at a particular location the color seen is blue?
Answer:
When white light is diffracted and at a particular location , the color seen is blue, this means that blue color is reflected while all other colors are absorbed or diffracted . This phenomenon is due to the absorbance of wavelengths of all other colors except blue.
Explanation:
An electron with a speed of 5x10 m/s experiences an acceleration of
magnitude 2x10" m/s° in a magnetic field of strength 2.6 T. What is
the angle between the velocity and magnetic field?
2. An electron is shot with a horizontal initial velocity in an upward
uniform magnetic field of 1.5 mT. It moves in a circle in the field.
a. (a) Does it move clockwise or counterclockwise?
b. (b) How long does each orbit take?
c. (c) If the radius of the circle is 1.3 cm then what is the speed of
the electron?
3. A long, straight wire on the x axis carries a current of 3.12 A in the
positive x direction. The magnetic field produced by the wire
combines with a uniform magnetic field of 1.45x10°that points in the
positive z direction. (a) Is the net magnetic field of this system equal
to zero at a point on the positive y axis or at a point on the negative y
axis? Explain. (b) Find the distance from the wire to the point where
the field vanishes.
4. A solenoid has a circular cross-section with a 3 cm radius, a length of
80 cm and 300 turns. It carries a current of 5 A. What is the magnetic
field strength inside the solenoid?
An electron with a speed of 5x10 m/s experiences an acceleration of magnitude 2x10" m/s° in a magnetic field of strength 2.6 T. the angle using a calculator, we find the angle to be approximately 0.001 radians. the speed of the electron to be approximately 2.42x10^6 m/s.
1. To find the angle between the velocity and magnetic field for an electron, we can use the formula:
a = (qvB) / m,
where a is the acceleration, q is the charge of the electron, v is the velocity, B is the magnetic field strength, and m is the mass of the eletron.
Given:
v = 5x10^6 m/s,
a = 2x10^6 m/s^2,
B = 2.6 T.
The charge of an electron is q = -1.6x10^-19 C, and the mass of an electron is m = 9.11x10^-31 kg.
Substituting the values into the formula:
2x10^6 = (1.6x10^-19)(5x10^6)(2.6) / (9.11x10^-31).
Simplifying the equation, we can solve for the magnitude of the angle:
angle = arctan(2x10^6 * 9.11x10^-31 / (1.6x10^-19 * 5x10^6 * 2.6)).
Calculating the angle using a calculator, we find the angle to be approximately 0.001 radians.
2. (a) Since the electron is moving in a circle in the magnetic field, its motion is perpendicular to the magnetic field. According to the right-hand rule, the direction of the force experienced by a negative charge moving perpendicular to a magnetic field is opposite to the direction of the field. Therefore, the electron moves counterclockwise.
(b) The time taken for each orbit can be calculated using the formula:
T = (2πm) / |q|B),
where T is the time period, m is the mass of the electron, q is the charge of the electron, and B is the magnetic field strength.
Given:
m = 9.11x10^-31 kg,
q = -1.6x10^-19 C,
B = 1.5 mT = 1.5x10^-3 T.
Substituting the values into the formula:
T = (2π * 9.11x10^-31) / (|-1.6x10^-19| * 1.5x10^-3).
Calculating the time period using a calculator, we find T to be approximately 3.77x10^-8 seconds.
(c) The speed of the electron can be determined using the formula for the centripetal force:
F = (mv^2) / r,
where F is the magnetic force acting on the electron, m is the mass of the electron, v is the velocity of the electron, and r is the radius of the circle.
Given:
m = 9.11x10^-31 kg,
v = unknown,
r = 1.3 cm = 1.3x10^-2 m.
The magnetic force acting on the electron is given by the equation:
F = |q|vB,
where q is the charge of the electron and B is the magnetic field strength.
Substituting the values and equations into the formula:
|q|vB = (mv^2) / r.
Simplifying the equation, we can solve for the speed of the electron:
v = (rB) / |q|.
Substituting the values:
v = (1.3x10^-2)(1.5x10^-3) / |-1.6x10^-19|.
Calculating the speed using a calculator, we find the speed of the electron to be approximately 2.42x10^6 m/s.
Learn more about magnetic field here:
https://brainly.com/question/30331791
#SPJ11
Electric room heaters use a concave mirror to reflect infrared (IR) iradiation from hot coils. Note that IR follows the siume law of reflection as visible light.
Find the magnification of the heater element, given that the mirror has a radius of curvature of 48 cm and produces an image of the coils 3.2 m away from the mirror.
M = ______________
the magnification of the heater element is 0.5.
radius of curvature (r) of the mirror = 48 cm
Image distance (v) = 3.2 m
Focal length (f) = r/2 = 48/2 = 24 cm
According to mirror formula:1/v + 1/u = 1/f
Where,
u is object distance.
In this case, u = -f [since the object is placed at the focus]
1/v = 1/f - 1/u=> 1/v = 1/24 + 1/24=> 1/v = 1/12=> v = 12 m
Magnification (M) is given as:
Magnification M = -v/u=> M = -12/-24= 0.5
So, the magnification of the heater element is 0.5.
Learn more about magnification:
https://brainly.com/question/131206
#SPJ11
&=8.854x10-¹2 [F/m] Ao=4r×107 [H/m] 16) A Hertzian dipole antenna, placed in free space, has a radiation resistance of 492 when it is connected to a 100 MHz source. The length of this antenna equals: a) 1.52 cm b) 5.09 cm c) 14.3 cm d) 21.4 cm e) None of the above. 18) An air-filled 3cmx1cm rectangular metallic waveguide operates at 15.5 GHz. The number of propagating TM modes equals: a) 1 b) 2 c) 3 d) 4 e) None of the above.
Question 16: The length of the antenna equals 7.54 cm, the correct option is (e) None of the above.
Question 18: There will be no propagating modes, the correct option is (e) None of the above.
Question 16: A Hertzian dipole antenna, placed in free space, has a radiation resistance of 492 when it is connected to a 100 MHz source. The length of this antenna equals
Given,
A Hertzian dipole antenna is placed in free space
The radiation resistance of the antenna when it is connected to a 100 MHz source is 492
We know that the radiation resistance of a short dipole antenna is given by
[tex]R_{r}[/tex] = 80π²r²/λ²,
where, r = length of the antenna, λ = wavelength of the radiation.
Rearranging, r = λ/4 × √([tex]R_{r}[/tex]/π²)……..(1)
The formula for the wavelength is given by
λ = c/f
where, c = speed of light, f = frequency of the radiation.
Putting the values,
λ = 3 × 10⁸/100 × 10⁶ = 3 m
Putting the value of λ in equation (1),
r = 3/4 × √(492/π²) = 0.0754 m = 7.54 cm
Therefore, the length of the antenna equals 7.54 cm.
Hence, the correct option is (e) None of the above.
Note: The given radiation resistance is of a Hertzian dipole antenna but the question is asking the length of a short dipole antenna. So, we have used the formula for a short dipole antenna.
Question 18: An air-filled 3 cm x 1 cm rectangular metallic waveguide operates at 15.5 GHz. The number of propagating TM modes equals
Given,
Air-filled rectangular metallic waveguide has dimensions 3 cm x 1 cm
The operating frequency is 15.5 GHz.
We know that the maximum frequency of operation for TE₁₀ mode in a rectangular waveguide is given by
[tex]f_c[/tex] = c/2a……(1)
where, c = speed of light, a = width of the waveguide (minimum dimension).
The formula for the cut-off frequency of TM₁₀ mode is given by
[tex]f_c[/tex] = c/2b…….(2)
where, b = height of the waveguide (maximum dimension).
From equation (1), the width of the waveguide is given by
a = c/2[tex]f_c[/tex]
From equation (2), the height of the waveguide is given by
b = c/2[tex]f_c[/tex]
So, the cut-off frequency of TM₁₀ mode is given by
[tex]f_c[/tex] = c/2b = c/2a
We have given the values of a = 1 cm and b = 3 cm.
So, we can write
[tex]f_c[/tex] = c/2b = c/2a = 15.5 GHz
From the above equation, the cut-off frequency is 15.5 GHz which is the operating frequency of the waveguide.
So, there will be no propagating modes.
Therefore, the correct option is (e) None of the above.
Learn more about dipole antenna here:
https://brainly.com/question/17414859
#SPJ11
You have a string with a mass of 0.0121 kg. You stretch the string with a force of 9.97 N, giving it a length of 1.91 m. Then, you vibrate the string transversely at precisely the frequency that corresponds to its fourth normal mode; that is, at its fourth harmonic. What is the wavelength λ4 of the standing wave you create in the string? What is the frequency f4?
The wavelength (λ₄) of the standing wave created in the string at its fourth harmonic is approximately 7.64 m, and the frequency (f₄) is approximately 3.30 Hz.
To find the wavelength (λ₄) and frequency (f₄) of the standing wave in the string at its fourth harmonic, we can follow these steps:
1. Calculate the velocity of the wave on the string.
The velocity (v) of the wave can be determined using the formula:
v = √(Tension / Linear mass density),
where Tension is the applied force and Linear mass density is the mass per unit length of the string.
Force (Tension) = 9.97 N
Mass of the string = 0.0121 kg
Length of the string = 1.91 m
The linear mass density (μ) can be defined as the ratio of mass to length.
μ = 0.0121 kg / 1.91 m = 0.00633 kg/m
Substituting the values into the formula:
v = √(9.97 N / 0.00633 kg/m)
v ≈ 25.24 m/s
2. Determine the wavelength (λ₄) of the standing wave.
At the fourth harmonic, the wavelength is equal to four times the length of the string:
λ₄ = 4 * Length of the string
λ₄ = 4 * 1.91 m
λ₄ ≈ 7.64 m
3. Calculate the frequency (f₄) of the standing wave.
f = v / λ,
where v is the velocity and λ is the wavelength.
Substituting the values:
f₄ = 25.24 m/s / 7.64 m
f₄ ≈ 3.30 Hz
Therefore, the wavelength (λ₄) of the standing wave created in the string at its fourth harmonic is approximately 7.64 m, and the frequency (f₄) is approximately 3.30 Hz.
Learn more about wavelength at: https://brainly.com/question/10750459
#SPJ11
The G Key below middle C on a piano keyboard vibrates with a
frequency of 390Hz. Determine the period of vibration.
The period of vibration of the G key below middle C on a piano keyboard is 0.0026 seconds.
Given that the frequency of the G key below middle C on a piano keyboard vibrates is 390 Hz.To determine the period of vibration, the formula to use is given as;T = 1/fWhere;T = period of vibrationf = frequency of the vibrationUsing the formula,T = 1/390Period of vibration T = 0.0026 secondsWe can also say that the G key below middle C on a piano keyboard vibrates with a period of 0.0026 seconds.Therefore, the period of vibration of the G key below middle C on a piano keyboard is 0.0026 seconds.
Learn more about Frequency here,
https://brainly.com/question/254161
#SPJ11
This time we have a non-rotating space station in the shape of a long thin uniform rod of mass 4.72 x 10^6 kg and length 1491 meters. Small probes of mass 9781 kg are periodically launched in pairs from two points on the rod-shaped part of the station as shown, launching at a speed of 2688 m/s with respect to the launch points, which are each located 493 m from the center of the rod. After 11 pairs of probes have launched, how fast will the station be spinning?
3.73 rpm
1.09 rpm
3.11 rpm
1.56 rpm
The correct option is c. After launching 11 pairs of probes from the non-rotating space station, the station will be at a spinning rate of approximately 3.11 rpm (revolutions per minute).
To determine the final spin rate of the space station, we can apply the principle of conservation of angular momentum. Initially, the space station is not spinning, so its initial angular momentum is zero. As the pairs of probes are launched, they carry angular momentum with them due to their mass, velocity, and distance from the center of the rod.
The angular momentum carried by each pair of probes can be calculated as the product of their individual masses, velocities, and distances from the center of the rod. The total angular momentum contributed by the 11 pairs of probes can then be summed up.
Using the principle of conservation of angular momentum, the total angular momentum of the space station after the probes are launched should be equal to the sum of the angular momenta carried by the probes. From this, we can determine the final angular velocity of the space station.
Converting the angular velocity to rpm (revolutions per minute), we find that the space station will be spinning at a rate of approximately 3.11 rpm after launching 11 pairs of probes.
Learn more about spinning rate here:
https://brainly.com/question/31236736
#SPJ11
a) Calculate the wavelength of light emitted by a Hydrogen atom when its electron decays from the n=3 to the n=1 state energy level. b) With respect to the photoelectric effect, the work function of Lead ( Pb) is 4.25eV. What is the cut-off wavelength of Pb ? c) A sample of Pb is illuminated with light having the wavelength calculated in part a). Calculate the velocity of the emitted electrons.
a) When an electron in a hydrogen atom transitions from the n=3 to the n=1 energy level, the wavelength of light emitted can be calculated using the Rydberg formula: 1/λ = R_H * (1/n_1^2 - 1/n_2^2), where λ is the wavelength, R_H is the Rydberg constant for hydrogen (approximately 1.097 × 10^7 m^-1), n_1 is the initial energy level (n=3), and n_2 is the final energy level (n=1).
b) The cut-off wavelength of lead (Pb) can be determined based on the work function, which is the minimum energy required to remove an electron from the metal surface. The relationship between the cut-off wavelength (λ_cutoff) and the work function (Φ) is given by λ_cutoff = hc / Φ, where h is Planck's constant (approximately 6.626 × 10^-34 J·s) and c is the speed of light (approximately 3.00 × 10^8 m/s). By substituting the value of the work function (4.25 eV) into the equation, we can calculate the cut-off wavelength of lead.
c) Once the wavelength of the emitted light from part a) is known, the velocity of the emitted electrons can be determined using the de Broglie wavelength equation: λ = h / mv, where m is the mass of the electron and v is its velocity. By rearranging the equation, we can solve for the velocity: v = h / (mλ). By substituting the mass of an electron and the calculated wavelength into the equation, we can find the velocity of the emitted electrons.
Learn more about the Rydberg formula, here:
https://brainly.com/question/32818875
#SPJ11
The smaller the resistance in an LRC circuit, the greater the resonance peak current. True False
False. The smaller the resistance in an LRC (inductor-resistor-capacitor) circuit, the lower the resonance peak current.
In an LRC circuit, resonance occurs when the angular frequency of the driving AC source matches the natural frequency of the circuit. At resonance, the current in the circuit is maximized. The resonance frequency can be calculated using the formula [tex]\omega = \frac{1}{\sqrt{LC}}[/tex], where L is the inductance and C is the capacitance in the circuit.
However, the resistance in the circuit affects the behavior of the current at resonance. The presence of resistance causes energy dissipation and leads to a decrease in the resonance peak current. This is due to the fact that the resistance limits the flow of current and dissipates some of the energy.
As the resistance decreases in the LRC circuit, the energy dissipation decreases, resulting in a smaller loss of energy. Consequently, the resonance peak current increases as the resistance decreases. Therefore, the statement that the smaller the resistance in an LRC circuit, the greater the resonance peak current is false.
Learn more about resistance here:
https://brainly.com/question/29427458
#SPJ11