The drag of the disk is 3.38 X 10^4.
What is drag?
Drag is a force that opposes any object's relative motion with respect to a surrounding fluid in fluid dynamics. This might be present between two liquid layers or between a liquid and a solid surface.
The resistance to motion of a body through a fluid, such as water or air, is known as a drag force. The direction of the incoming flow velocity is opposed by a drag force. This is the relative speed of the fluid and the body.
Solution Explained:
Given,
Specific gravity(sg) = 0.87
Diameter = 0.01ft
Density of Oil (P) = [tex]sg_{ph20} = 0.87 X 1.94 = 1.6878 \frac{sl}{ft^3}[/tex]
Since the viscosity is 10000 times that of water, the Reynold number is
[tex]R_{E} = \frac{PvD}{meu} = \frac{1.6878 X 0.01 X 0.01}{0.234} = 7.21 X 10^-4[/tex]
Since RE < 1, the drag coefficient for normal flow is given as:
[tex]CD = \frac{24.4}{R_{E}} = \frac{24.4}{7.21 X 10^-4} = 3.38 X 10^4[/tex]
To learn more about drag, use the link given
https://brainly.com/question/28764812
#SPJ4
when conducting a cylinder leakage test, technician a says the piston must be at the top of the cylinder (tdc) when the test is being performed. technician b says a reading of 0 percent leakage indicates the piston rings are worn or broken. who is correct?
After conducting a cylinder leakage test, Technician A is correct.
What is a cylinder head?
The cylinder head serves as the ceiling of the combustion chamber in an internal combustion engine and is located above the cylinders. They are essential for managing fuel deployment and airflow into and out of the cylinders.
The engine valves are located in the cylinder head. Allowing air into and out of the cylinder is the main purpose of the engine valve. The cylinder head, which houses more moving parts than any other component of the engine, also houses the injectors and valves.
To learn more about a cylinder valve, use the link given
https://brainly.com/question/18204706
#SPJ4
in the pseudo-nmos realization of a 2-input nor gate, the pull-down network is realized using minimum size transistors (2/4). the l/w ratio of the pmos transistor should be:
The I/w ratio is the ratio of the current flowing through a transistor to the width of the transistor's channel.
What should be the ratio?The l/w ratio of the PMOS transistor in a pseudo-NMOS realization of a 2-input NOR gate should be determined by the design requirements of the circuit.
In general, the l/w ratio of a PMOS transistor is determined by the desired current-carrying capability and the voltage drop across the transistor. For a 2-input NOR gate, the PMOS transistor in the pull-up network should be designed to provide sufficient current to drive the output high, while the PMOS transistors in the input stages should be designed to have a low on-resistance to minimize the voltage drop across them.
The exact l/w ratio will depend on the specific design requirements of the circuit.
To Know More About Transistors, Check Out
https://brainly.com/question/29432407
#SPJ1
joe is an exceptional systems engineer who hopes to work at the techtonic group. he is handicapped and uses a wheelchair. techtonic does not have wheelchair ramps and some doorways are not wide enough for a wheelchair. the hr department should
The HR department should install wheelchair ramps and widen the doorways as they don't want to loose an exceptional systems engineer who hopes to work at the techtonic group.
What is a wheelchair ramps?
A wheelchair ramp is an inclined plane that can be installed in addition to or instead of stairs. Ramps make it easier for wheelchair users, as well as people pushing strollers, carts, or other wheeled objects, to enter a building.
The Americans with Disabilities Act requires wheelchair ramps (or other ways for wheelchair users to access a building, such as a wheelchair lift) in new construction for public accommodations in the United States.
A wheelchair ramp can be fixed, semi-fixed, or portable. Permanent ramps are intended to be bolted or otherwise attached to the ground. Semi-permanent ramps are commonly used in the short term and rest on top of the ground or concrete pad.
To know more about wheelchair ramps, visit: https://brainly.com/question/17395685
#SPJ4
A horizontal load P = 62 kN is applied at A of the assembly as shown. Determine (a) the internal force in bar BD, (b) the reaction at the pinned support C.
Internal force is 75 kN and reaction is 82.9 kN, according to the question.
What in science is a force?The word "force" has a specific meaning in science. At this level, calling a force a pushing or a pull is entirely appropriate. A power is not something an object "has in it" or that it "contains." One thing experiences a force from another. There are both living things and non-living objects in the concept of a force.
Who made the force?Issac Newton's third laws of motion, which are outlined in his Principia Mathematica, are frequently used to illustrate the concept of force (1687).
To know more about force visit:
https://brainly.com/question/13191643
#SPJ1
110-v rms, 60-hz source is applied to a load impedance z. the apparent power entering the load is 120 va at a power factor of 0.607 lagging. note: this is a multi-part question. once an answer is submitted, you will be unable to return to this part. calculate the complex power. the complex power is j va.
The term "complex power" refers to the mathematical representation of electrical power. It has both real and fictitious parts, just like a complex number.
The active power is represented by the real part, while the reactive power is represented by the imaginary part. The letter S is frequently used to represent it.
What does complex power entail?The complex conjugate of the rms current phasor and the rms voltage phasor make up the complex power (in VA). As a complex quantity, its real and imaginary parts are real power P and reactive power Q, respectively.
Since the magnitude of the complex power is the apparent power, we could write it as:
S=S∠θ v−θ i
However, mathrm pf = cos(theta_v-theta_i) pf = cos(v i)
v i = cos 1 pf = 45 In this case, the value of the ta_v-theta_i v i is positive due to the exercise's knowledge that current lags voltage. The value of the complex power is:
Boxed mathbf S=120, angle 45, circle mathrm VA S=120, 45, VA
a) "mathbf S=120 angle 45 circle" "mathrm VA S=120 45"
To learn more about complex power here:
https://brainly.com/question/2355649
#SPJ1
Complete Question = A 110-V rms, 60-Hz source is applied to a load impedance Z. The apparent power entering the load is 120 VA at a power factor of 0.707 lagging. (a) Calculate the complex power. (b) Find the rms current supplied to the load. (c) Determine Z. (d) Assuming that Z = R + jωL, find the values of R and L.
A coal barge is 1000-ft-long, 100-ft-wide, and is submerged in 12 feet of 60°F water. If it is being towed at 12 mph, estimate the friction drag.
friction drag = 54546 lbf
A coal barge is 1000-ft-long, 100-ft-wide, and is submerged in 12 feet of 60°F water. If it is being towed at 12 mph, the friction drag would be 54546 lbf.
What is a Friction drag?
Friction is the resistance that occurs when two objects rub together, such as air against an airplane. Friction contributes to drag.
Because the barge is rectangular, the flow over the submerged sides and bottom is assumed to behave like B.L. over a flat plate.
Effects at the corners and leading/trailing edges are not taken into account, which could lead to deviations from the analysis. Given the size of the barge, we expect these effects to be minor.
To know more about friction, visit: https://brainly.com/question/29355763
#SPJ4
You need to replace a fiber optic cable that is connecting two switches together. You inspect the existing fiber cable and determine that it uses LC connectors. You also notice the cable's ferrule has a slight slant to it. Which polish grade should you use to replace the existing cable?
Angled Physical Contact polish
So, To replace the fiber optic cable that connects two switches. If it is found that the existing fiber cable to ensure it has LC connectors and also if the cable's ferrule has a slight slant to it.
Angled Physical Contact polish should be used to replace the existing cable.
What is Angled Physical Contact polish?
APC Connector is a type of fiber connector that reduces back-reflection by applying a 5° to 15° angle-polish to the end faces.
Because of the angle, the reflected light escapes into the cladding rather than remaining in the fiber core.
Angled connectors should only be mated with other angled connectors. When mated to a non-angle polished connector, insertion loss is extremely high. Angle-polished connectors typically have a higher insertion loss than good quality straight physical contact connectors.
When connected, "Ultra" quality connectors may achieve back reflection comparable to an angled connector, but an angled connection maintains low back-reflection even when the output end of the fiber is disconnected.
To know more about fiber Optics, visit: https://brainly.com/question/15741826
#SPJ4
an amount p is deposited now so that an equal annual amount of a1=2000 per year for the first five years,starting one year after the deposit. and a different annual withdrawal of a2=3000 per year for the following three years ,draw the cash flow diagram if i=8.5% per year
The cash flow diagram is shown below:
Year Deposit Withdrawal Balance
0 P - P
1 - - P
2 - 2,000 P + 1,708.50
3 - 2,000 P + 3,571.51
4 - 2,000 P + 5,539.52
5 - 2,000 P + 7,614.45
6 - 3,000 P + 5,978.7
7 - 3,000 P + 4,037.48
8 - 3,000 P + 2,068.83
What is deposit ?
Placing cash with an organization, most frequently a financial institution like a bank, is known as making a deposit. The deposit is a credit again for person that made it, and it may be withdrawn in line with the terms agreed upon at the time of deposit, passed to some other party, or applied to a purchase at a later time.
To know more about deposit
https://brainly.com/question/2507231
#SPJ1
How can I create this code this in Python?
Use the random module to generate a random number, prompt the user for a guess at the number until the user guesses the number. When the guess is too high, let the user know, when too low let them know, and when they guess it let them know it was correct and in how many guesses.
The program in Phyton that meets the above requirements is:
# import the random module
import random
# generate a random number between 1 and 10
number = random.randint(1, 10)
# initialize the number of guesses to 0
guesses = 0
# prompt the user for a guess and keep track of the number of guesses
while True:
guess = int(input('Guess a number between 1 and 10: '))
guesses += 1
# if the guess is too low, let the user know
if guess < number:
print('Your guess is too low.')
# if the guess is too high, let the user know
elif guess > number:
print('Your guess is too high.')
# if the guess is correct, let the user know and exit the loop
else:
print('You guessed the number in', guesses, 'guesses!')
break
What is the explanation?This software creates a random number between 1 and 10, prompts the user for a guess, and keeps track of how many guesses are made. If the user's guess is too low, it produces an error message. If the user's guess is too high, it produces an error notice.
If the user successfully guesses the number, it publishes a message informing them of their success and the number of guesses required and then exits the loop.
Learn more about the program:
https://brainly.com/question/11023419
#SPJ1
Minitab: Suppose you own two pottery stores in your city. You want to find the number of two particular vase colors (color) sold in both stores (location) each week (for each week). You are not interested in the sum total. Which bar graph should you select to compare the data between both stores?
Select an answer:
Stacked Bar Chart
Cluster Bar Chart
Simple Bar Chart
Boxplot Chart
Where you own two pottery stores in your city and you want to find the number of two particular vase colors (color) sold in both stores (location) each week (for each week). If are not interested in the sum total, note that the bar graph you should select to compare the data between both stores is: the "Stacked Bar Chart" (Option A)
What is the advantage of the Stacked Bar Chart?When comparing data points, a stacked bar chart is generally simpler to notice the comparison than a combined chart.
When data points are stacked on top of each other, it is easier to discern the percentage of each data point relative to the total value.
Learn more about Stacked Bar Chart:
https://brainly.com/question/28903290
#SPJ1
I have
V(tension) =12W
Vr2=7,2W
Vr1=4,8W
R(resitance)2=1800 ohm
How much is
I1 and R2
The current and the resistance are obtained according to Ohm's First Law, which states that the voltage is obtained by the multiplication of the resistance and of the current, as follows:
V = R x I.
The variables are:
V is the voltage.R is the resistance.I is the current.At resistor R2, we have that:
The current is I1, as it is the same for the entire loop.The resistance is of 1800 ohms.The voltage is of 7.2 volts.Hence the current I1 is obtained as follows:
1800 x I1 = 7.2
I1 = 7.2/1800
I1 = 0.004A = 4mA.
Then for resistor R1, we have that:
The voltage is of 12 - 7.2 = 4.8 V, as the voltage for the entire loop is of zero.The current is of 0.004A.Hence the resistance R1 is obtained as follows:
0.004R1 = 4.8
R1 = 4.8/0.004
R1 = 1200 ohms.
More can be learned about Ohm's First Law at https://brainly.com/question/231741
#SPJ1
A torage tank for concentrated nitric acid will be contructed from aluminum to reit corroion. The tank i to have an inide diameter of 6 m and a height of 17 m. The maximum liquid level in the tank will be 16 m. Etimate the plate thickne required at the bae of the tank. Take the allowable deign tre for aluminum a 90 N/mm2
Taking the allowable design stress for aluminium as 90 N/mm². The estimated plate thickness required at base of tank is 0.1612m.
What is stress?Stress is a force per unit area that occurs in materials as a result of external forces, uneven heating, or permanent deformation. It is used in physical sciences and engineering to accurately describe and predict the behavior of elastic, plastic, and fluid materials. A stress is defined as the product of a force divided by an area.
There are numerous types of stress. Shear stress is caused by forces that are parallel to and lie in the plane of a cross-sectional area of the material, as opposed to normal stress, which is caused by forces that are perpendicular to the area.
Learn more about stress
https://brainly.com/question/26108464
#SPJ1
Write an Assembly language program that queries an integer (1 s k s 365) from the keyboard in a loop. Then calculates and displays information about what will be the next day of the year: Saturday, Sunday or working day, if January 1: 1) Monday; 2) b) the d-th day of the week (if January 1 is Monday, then d = 1 if Tuesday = 2,..., if Sunday -d = 7). The input ends when you press the EЅС key.
Answer:
This program uses the int 16h interrupt to query an integer from the keyboard and store it in the al register. The program then enters a loop, in which it calculates the next day of the week using the add, mov, div, and cmp instructions, and displays the appropriate message using the int 21h interrupt. The program exits the loop and ends when the user presses the ESC key (ASCII code 27).
Oil companies benefit from capturing ____ ____ and then injecting it back into aquifers because the increased pressure enhances oil recovery. they also save money from less taxes on emissions
Capturing carbon dioxide is advantageous for oil corporations.
What part does the oil industry play in global warming?When fossil fuels are burned, a greenhouse gas called carbon dioxide is massively released into the atmosphere. Greenhouse gases, which trap heat in our atmosphere, are to blame for global warming.
How is the environment benefited by carbon capture and storage?Before carbon dioxide (CO2) is released into the atmosphere, it is captured and stored through the process of carbon capture and storage (CCS). The technique can absorb up to 90% of the CO2 produced while burning fossil fuels to produce power and for industrial purposes like making cement.
To know more about oil visit:-
https://brainly.com/question/29530758
#SPJ4
Two doubles are read as the power and the distance of a SoundWave object. Declare and assign pointer mySoundWave with a new SoundWave object using the power and the distance as arguments in that order. Ex: If the input is 2.5 1.5, then the output is:SoundWave's power: 2.5SoundWave's distance: 1.5Code:#include #include using namespace std;class SoundWave {public:SoundWave(double powerValue, double distanceValue);void Print();private:double power;double distance;};SoundWave::SoundWave(double powerValue, double distanceValue) {power = powerValue;distance = distanceValue;}void SoundWave::Print() {cout << "SoundWave's power: " << fixed << setprecision(1) << power << endl;cout << "SoundWave's distance: " << fixed << setprecision(1) << distance << endl;}int main() {SoundWave* mySoundWave = nullptr;double powerValue;double distanceValue;cin >> powerValue;cin >> distanceValue;/* Your code goes here */mySoundWave->Print();return 0;}
The power and the distance of a SoundWave object is
SoundWave* mySoundWave = new SoundWave(powerValue, distanceValue);
What is power?
Power is the ability to exercise control or influence over something or someone. It is the capacity to make decisions, take action, and shape events. Power is derived from a position or authority within an organization, while informal power is derived from personal characteristics such as charisma, intelligence, and experience. Power can be used for good or ill, depending on the person wielding it and the situation. The use of power should always be guided by ethics and responsibility, and those in positions of power should strive to build trust and credibility.
To learn more about power
https://brainly.com/question/25864308
#SPJ4
Multiple Choice question. Selected the correct answer.
10. Which of the following is NOT a metal used for producing exhaust manifolds?
A. Cast iron.
B. Aluminium.
C. Heavy-gauge sheet metal.
D. Stainless steel.
Answer:
C. Heavy-gauge sheet metal.
Explanation:
Exhaust manifolds are typically made from cast iron, aluminum, or stainless steel, which are strong and durable materials that can withstand the high temperatures and pressures found in vehicle exhaust systems.
Heavy-gauge sheet metal is a type of metal, but it is not typically used for this application because it may not have the necessary strength and durability.
data mining uses the following techniques (select all that applies) group of answer choices hypothesis testing statistical modeling search algorithms machine learning etl technology
knowledge extraction from data It is one of the processes in the procedure for discovering new knowledge. It is a computational process that combines techniques from machine learning, statistics, and database architecture to find patterns in massive data sets.
What four tasks does data mining perform?Data mining mostly serves the following four purposes: prediction capability. the method of extracting patterns from data utilizing a number of variables to forecast other variables with unknown types or values. The process of searching a database for a crucial feature of data.
What methods of data mining are there?Some data mining techniques include classification, clustering, association, data cleaning, and data visualization.
To know more about data mining visit :-
https://brainly.com/question/28561952
#SPJ4
Create a class called Car that includes three instance variables—a model (type
String), a year (type String), and a price (double). Provide a constructor that initializes the three
instance variables. Provide a set and a get method for each instance variable. If the price is not positive,
do not set its value. Write a test application named CarApplication that demonstrates class Car’s capabilities. Create two Car objects and display each object’s price. Then apply a 5% discount on the
price of the first car and a 7% discount on the price of the second. Display each Car’s price again.
Answer:
Here is the implementation of the Car class:class Car {
private String model;
private String year;
private double price;
public Car(String model, String year, double price) {
this.model = model;
this.year = year;
if (price > 0) {
this.price = price;
}
}
public String getModel() {
return model;
}
public void setModel(String model) {
this.model = model;
}
public String getYear() {
return year;
}
public void setYear(String year) {
this.year = year;
}
public double getPrice() {
return price;
}
public void setPrice(double price) {
if (price > 0) {
this.price = price;
}
}
}
Here is the test application that demonstrates the capabilities of the Car class:class CarApplication {
public static void main(String[] args) {
Car car1 = new Car("Toyota", "2020", 20000);
Car car2 = new Car("Honda", "2019", 25000);
System.out.println("Original price of car1: $" + car1.getPrice());
System.out.println("Original price of car2: $" + car2.getPrice());
car1.setPrice(car1.getPrice() * 0.95);
car2.setPrice(car2.getPrice() * 0.93);
System.out.println("Discounted price of car1: $" + car1.getPrice());
System.out.println("Discounted price of car2: $" + car2.getPrice());
}
}
Let’s say you are setting up your ANOVA one-way analysis of variance graph. How many residual plots can you view at one time?
Select an answer:
two plots
one plot
five plots
three plots
The number of residual plots that you can view at one time is A. two plots.
What is analysis of variance?Analysis of variance is a collection of statistical models and the estimation procedures that go with them that are used to analyze the differences between means. Ronald Fisher, a statistician, invented ANOVA.
ANOVA, which stands for Analysis of Variance, is a statistical test used to compare the means of multiple groups. ANOVA ("analysis of variance") compares the means of two or more independent groups to see if there is statistical evidence that the associated population means differ significantly.
In conclusion, the correct option is A.
Learn more about ANOVA on:
https://brainly.com/question/25800044
#SPJ1
given the instruction set for marie: write the assembly language equivalent for the machine instruction: 1000 100000000000 (8800).
The appropriate machine instruction in assembly language for the Skipcond 800 given the following instruction set.
Is machine code the same as assembly?The primary distinction between assembly language and machine code is that the latter is a low-level programming language that needs an assembler to translate it into machine code. Machine code, on the other hand, is a language made up of binaries that can be run by computers directly.
Does binary correspond to machine language?The most basic form of information stored in a computer system is binary information, which is also frequently referred to as machine language. Physically speaking, a computer system's central processing unit stores the 0s and 1s utilizing.
To know more about assembly language visit :-
https://brainly.com/question/14728681
#SPJ4
figure below shows a rudder mechanism used to steer ships. at the instant shown, the actuator is being extended at a constant rate of 0.1 m/s. determine the rotational velocity and acceleration of the rudder assembly.
The rotational velocity of the rudder mechanism to steer the ship is .1247 rad/sec.
What does rotational motion?Translational motion is when an object moves in a straight line, whereas rotational motion occurs when the same object moves in a circular route along an axis.
Briefing:1)here rotational velocity and acceleration of the rudder can be found by relative velocity and acceleration method with Coriolis component of acceleration
2)here let's draw a velocity diagram as follow with the scale of
2 cm=.1 m/s
velocity triangle is given by AB'B, where AB' shows slider velocity along horizontal, AB along the tangent to link 2 or guide, and velocity of pin BB' inside the guide along the length of the guide, here we know the velocity of AB' but don't know velocity AB and BB' hence draw them along given direction point of intersection is B point, so from the diagram, I get that
Vab'=2 cm=.1 m.s
Vbb'=.9 cm=.045 m/s
Vab=1.9 cm=.095 m/s
where rotational velocity is given by
Vab=Rab*wab
Rab=(.362+.7^2)^.5=.7615 m
wab=0.095/.7615=.1247 rad/s
To know more about rotational motion visit:
https://brainly.com/question/12995374
#SPJ4
say there is a b -tree primary index on a relation r. since an insert or a delete into r changes the index as well, we must take locks on the index during updates. briefly explain what kind of locks you would take on the index pages when doing an insert or a delete into the relation. remember a page split or merge may involve the ancestors and the siblings of a node.
Any subnode of a given node is called a child node, and the given node, in turn, is the child's parent.
What is ancestor node?Beginning with the parent node and continuing through to the root node, the ancestor axis displays all of the context node's ancestors. Exactly like Following-Siblings, this idea is a notion. Functionality-wise, the only change is what came before. In this case, as opposed to Following-Sibling, you receive information on all the nodes that are siblings or on the same level as your present node but are located earlier in the tree. We must use xpath's following-sibling idea in order to navigate to the subsequent sibling. Through the current sibling of the same parent, we can then move on to the following sibling.To learn more about ancestor node refer to:
https://brainly.com/question/29749643
#SPJ4
Matrix Keypad Scan (5 points). Explain why we have to use external pull-up on the column pins in the keypad lab, instead of internal pull-up provided by each GPIO pin. 3.3V +3.3V +3.3v R2 Output Port (Output from rocsso R3 R4 C1 C2 C3 Input Port (Input to the processor)
The Raspberry Pi may interact with electronic circuits via the GPIO pins to monitor and control the environment
What are the uses of GPIO pins?The Raspberry Pi may interact with electronic circuits via the GPIO pins to monitor and control the environment. The Pi can operate motors, drive LEDs to turn on or off, and communicate with a variety of other devices.An uncommitted digital signal pin on an electronic circuit (such as an MCU or MPU board) that can be used as an input, output, or both is known as a general-purpose input/output (GPIO). GPIOs are by default unused and serve no known use.A GPIO (general purpose input/output) pin enables you to either deliver output to the user or receive input for your programme from sources other than the CPU.To learn more about GPIO refer,
https://brainly.com/question/29240962
#SPJ4
Before Segway manufactured its two-wheeled people movers, it built a prototype and had staff engineers test it for performance and stability. At this stage, Segway was involved inalpha testing.product launch.test marketing.beta testing.concept testing.alpha testing
At this stage, Segway was involved in "alpha testing", when Segway manufactured its two-wheeled people movers, it built a prototype and had staff engineers test it for performance and stability.
What exactly is a Protoype?
Prototyping is an important step in the creation of any product, digital or physical. The process transforms the concept into a physical structure. This concept can be presented to stakeholders or an audience to validate assumptions and test its viability.
In simple terms, a prototype is not just a component of product design; it is one of the most important components of -
Determine whether the proposed product is viable for mass production.Before the actual product is developed, provide stakeholders and investors with an overview of the product.Prototyping is an essential step in the startup process without which all subsequent steps are pointless.
To know more about Protoype, visit: https://brainly.com/question/17205672
#SPJ4
two technicians are discussing clogged egr passages. technician a says that clogged egr passages can cause excessive nox exhaust emission. technician b says that clogged egr passages can cause the engine to ping (spark knock or detonation). which technician is correct?
Where two technicians are discussing clogged EGR passages and Technician A says clogged EGR passages can cause excessive NOx exhaust emission and Technician B says that clogged EGR passages can cause the engine to ping (spark knock or detonation), note that BOTH technicians are correct. (Option C)
What is a Clogged Exhaust Gas Recirculation (EGR) Passage?These systems' passageways can get blocked, obstructing the flow and resulting in inadequate EGR flow, explosion, and excessive NOx emissions. If the solenoid, circuits, and EGR valve are all functioning properly and the route is clogged, cleaning the passageways with a wire brush will restore normalcy to the system.
When the EGR valve becomes clogged, the engine suffers a considerable loss of power, hauls, or difficulty of cold starts, as well as increased smoke emissions. If the EGR valve remains closed, it will not be able to reduce pollutants.
Learn more about NOx Exhaust Emission:
https://brainly.com/question/27245596
#SPJ1
Full Question;
Two technicians are discussing clogged EGR passages. Technician A says clogged EGR passages can cause excessive NOx exhaust emission. Technician B says that clogged EGR passages can cause the engine to ping (spark knock or detonation). Which technician is correct?
Technician A only
Technician B only
Both Technicians A and B
Neither Technician A nor B
Suppose that your car will not start. To determine whether the battery is faulty, you turn
on the light switch and find that the lights are very dim, indicating a weak battery. You
borrow a friend’s car and a set of jumper cables. However, how do you connect his
car’s battery to yours? What do you want his battery to do?
Note that to connect your car's battery to your friend's car using jumper cables, you should follow these steps:
Allow the two automobiles to be near to each other but not to touch.Check that both automobiles are switched off and that the keys are not in the ignition. Open the hoods of both vehicles.Find the batteries in both vehicles. The positive terminal (generally denoted by a "+") is usually bigger than the negative terminal.Connect the positive terminal of your friend's battery to one end of the red jumper cable. Connect the other end of the red jumper cable to the positive connector of your vehicle's battery.Connect the negative terminal of your friend's battery to one end of the black jumper cable.Attach the other end of the black jumper cable to an unpainted metal surface on your automobile, such as an engine block bolt. This will assist in grounding the circuit and preventing sparks.What are the signs of a faulty battery?If your engine cranks slowly, like it's tougher to start on chilly mornings, start inconsistently, or there's no sound or interior lights when you try to start, consider a failing battery, a loose or corroded connection, or an electrical draw.
To make sure your battery lasts:
Short travels should be avoided. Short automobile journeys restrict your car's battery from fully charging.Keep your battery securely attached.When you exit the car, turn off all lights.Maintain corrosion control.Check your battery frequently.When the engine is turned off, do not utilize electronics.Learn more about Battery:
https://brainly.com/question/23716491
#SPJ1
in a linkage-operated clutch system, technician a says the need for free play adjustment may be due to a worn clutch plate. technician b says the free play should be adjusted at the pedal pushrod which is usually under the dash. who is correct?
Answer: Technician B is correct.
In a linkage-operated clutch system, the free play should be adjusted at the pedal pushrod which is usually under the dash.
Clutch slip will occur if there is insufficient free play (or clearance), as the pressure plate won't be able to fully press against the friction plate. If this problem isn't fixed right away, a burned-out friction plate and potentially a damaged pressure plate will result.
What is Clutch Operated Linkage?
A stiff component of the flywheel and consequently the crankshaft assembly is the clutch unit.
As a result, it experiences vibrations from the engine and transmission as rocking, shaking, and pitching.
On the other hand, the clutch foot-pedal assembly is fastened to the body framework. As a result, the body may experience minor bumps and rebound motions.
To know more about Clutch, visit: https://brainly.com/question/13507668
#SPJ4
just below 723 c, a hypereutectoid plain carbon steel contains 11 wt % eutectoid fe3c. what is its average carbon content in weight percent? (12 points)
The average carbon content in weight percent is 0.090%. To calculate the average of carbon is shown below.
High-carbon steel, of course, has the highest ratio of carbon to iron. It includes of more than 0.60% carbon, thereby changing its physical properties. Also called as carbon tool steel, it has around 0.61% to 1.5% carbon. The carbon percentage refers to a high percentage of carbon gives hardness and strength to the metal. It is primary used to tools like chisels, hammers, dies, punches, broaches, reamers, drills, taps, etc.
To determine the average carbon content in weight percent, the equation will be:
0.11 = ((6.67-x)/(6.67-0.02)). x
0.11 = (6.67 - x )/6.65x
73.15x = 6.67 - x
74.15 x = 6.67
x = 0.090%
Learn more about the average carbon, here https://brainly.com/question/8746255
#SPJ4
please help me
How urban planning can improve public health?
Answer:
search it bro
Explanation:
use it, it will give precise answer
Can you find thevenin equivalent for this example?
With the load impedance open-circuited, the Thevenin voltage is calculated. Find the voltage at the load terminals that is open-circuit.
Explaining Thevenin's TheoremThevenin's Theorem: What is it? According to Thevenin's Theorem, any linear circuit can be made simpler by using a single dc voltage and a series resistance, regardless of how complex it is.
What are Thevenin's theorem's benefits?It makes the less crucial section of the circuit simpler and makes it possible for us to see the output part's operation in real time. It simplifies a complicated circuit by putting one emf source in series with one resistance.
To know more about Thevenin's Theorem visit:
https://brainly.com/question/28007778
#SPJ1