Inductive reactance of the circuit= 53.66 Ohm
Capacitive reactance of the circuit= 12.24 Ohm
Impedance of the circuit = 98.89 Ohm
RMS current in the circuit = 1.32 A
Frequency to maximize the current = 105.43 Hz.
a) Inductive reactance of the circuit
Inductive reactance is given by the formula:
X(L) = 2πfL
Where,
f is the frequency
L is the inductance.Inductive reactance = 2πfL= 2 × 3.14 × 65 Hz × 130 mH= 53.66 Ohm (approx)
b) Capacitive reactance of the circuit
Capacitive reactance is given by the formula:
X(C) = 1/2πfC
Where, f is the frequency and C is the capacitance.
Capacitive reactance = 1/2πfC= 1/2 × 3.14 × 65 Hz × 200 µF= 12.24 Ohm (approx)
c) Impedance of the circuit
The impedance of the circuit is given by the formula:
Z = √(R² + (X(L) - X(C))²)
Where,
R is the resistance of the circuit,
X(L) is the inductive reactance,
X(C) is the capacitive reactance.
Impedance of the circuit = √(R² + (X(L) - X(C))²)= √(90² + (53.66 - 12.24)²)= 98.89 Ohm (approx)
d) RMS current in the circuit
RMS current in the circuit is given by the formula:
I(RMS) = V(RMS)/Z
Where,
V(RMS) is the RMS voltage of the alternating voltage source.
I(RMS) = V(RMS)/Z= 130 V / 98.89 Ohm= 1.32 A (approx)
e) Frequency to maximize the current in the circuit
To maximize the current in the circuit, we need to find the resonant frequency of the circuit. The resonant frequency of an RLC circuit is given by the formula:
f0 = 1/(2π√(LC))
Where,
L is the inductance
C is the capacitance.
f0 = 1/(2π√(LC))= 1/(2π√(130 mH × 200 µF))= 105.43 Hz (approx)
Therefore, the frequency that should be used to maximize the current in the circuit is approximately 105.43 Hz.
Learn more about capacitive reactance.
https://brainly.com/question/14579743
#SPJ11
Flywheel of a Steam Engine Points:40 The flywheel of a steam engine runs with a constant angular speed of 161 rev/min. When steam is shut off, the friction of the bearings and the air brings the wheel to rest in 2.0 h. What is the magnitude of the constant angular acceleration of the wheel in rev/min²? Do not enter the units. Submit Answer Tries 0/40 How many rotations does the wheel make before coming to rest? Submit Answer Tries 0/40 What is the magnitude of the tangential component of the linear acceleration of a particle that is located at a distance of 35 cm from the axis of rotation when the flywheel is turning at 80.5 rev/min? Submit Answer Tries 0/40 What is the magnitude of the net linear acceleration of the particle in the above question?
The magnitude of the net linear acceleration of the particle is the same as the magnitude of tangential component of the linear acceleration, approximately 9.58 cm/min².
To find the magnitude of the constant angular acceleration, we first convert the given angular speed to radians per second: Angular speed = 161 rev/min
= 161 * 2π radians/minute
= 161 * 2π * (1/60) radians/second
≈ 16.85 radians/seconsecond
Now, we can use the equation of angular motion to find the angular acceleration:
Δθ = ω₀t + (1/2)αt²
0 = 16.85 * 120 + (1/2)α * (120)²
α ≈ -0.000294 rev/min²
To find the number of rotations the wheel makes before coming to rest, we can use the formula: Number of rotations = (ω₀² - ω²) / (2α)
Plugging in the values: Number of rotations = (16.85² - 0) / (2 * -0.000294)
≈ 322 rotations
Next, we can find the tangential component of the linear acceleration using the formula: Linear acceleration = r * α
Given that the distance from the axis of rotation is 35 cm (0.35 m): Linear acceleration = 0.35 * 16.85 * 0.000294
≈ 9.58 cm/min²
Learn more about acceleration here;
https://brainly.com/question/25876659
#SPJ11
9. When characterizing a fuel cell based on a proton conductor, is it advisable to supply steam to the anode, to the cathode, or to both? Why? State the connection to the Nernst potential.
The reason behind this is that fuel cells require moisture for their proper functioning, and thus, water is required to keep the proton conductor hydrated and function properly.
When characterizing a fuel cell based on a proton conductor, it is advisable to supply steam to the anode and cathode. The reason behind this is that fuel cells require moisture for their proper functioning, and thus, water is required to keep the proton conductor hydrated and function properly.
Water is an essential component of proton conductors and is used as a source of protons in fuel cells. If there is insufficient water in the proton conductor, then the rate of proton conduction will be reduced, leading to a decrease in the output voltage of the fuel cell. This can also lead to the collapse of the proton gradient, which can hamper the functioning of the fuel cell.
Therefore, to avoid such a situation, it is advisable to supply steam to both the anode and cathode of a fuel cell to keep the proton conductor hydrated and functioning properly. Moreover, the Nernst potential is affected by the steam supplied to the fuel cell. The Nernst potential is the maximum potential difference that can be achieved by a fuel cell. The Nernst potential of a fuel cell based on a proton conductor is dependent on the concentration of protons and the partial pressure of hydrogen at the anode and the partial pressure of oxygen at the cathode.
Supplying steam to the anode and cathode can help regulate the partial pressure of hydrogen and oxygen, which in turn, can affect the Nernst potential of the fuel cell. Therefore, the steam supplied to the fuel cell can have a direct connection to the Nernst potential.
Learn more about fuel cell on:
https://brainly.com/question/12470020
#SPJ11
Speakers 1 and 2 simultaneously emitted sound intensity levels of 50 dB and 70 dB respectively. What is the resultant intensity of the sound (express it in dB)? Show your work.
Hence, the resultant intensity of the sound is 120.043 dB.
The intensity of the sound is the sound energy per unit area and is measured in watts per square meter. Sound intensity, like sound pressure, is normally measured in decibels. The decibel scale, abbreviated dB, ranges from 0 dB, the threshold of hearing, to about 120 dB, the threshold of pain or discomfort. A decibel is one-tenth of a bel.The sound intensity level is the decibel (dB) level produced by a sound wave, which is a measure of the energy in the sound wave. The sound intensity level of a sound wave is determined by the amplitude, or height, of the wave.The formula for calculating sound intensity in decibels is I = 10log (I/10-12), where I is the intensity of the sound in watts per square meter. Now, let's find the resultant intensity of the sound of speakers 1 and 2 respectively.First, convert the sound intensities of speaker 1 and 2 to watts/m2 by using the equation I = 10^((dB - 12)/10).Speaker 1 intensity level = 50 dBI₁ = 10^((50 - 12)/10) = 6.31 × 10⁻⁶ W/m²Speaker 2 intensity level = 70 dBI₂ = 10^((70 - 12)/10) = 1 W/m²The resultant intensity of sound = I = I₁ + I₂ = 6.31 × 10⁻⁶ + 1 = 1.00000631 W/m². The sound intensity in decibels is: Sound intensity level = 10 log10(I/10-12) = 10 log10(1.00000631/10-12) = 120.043 dB. Hence, the resultant intensity of the sound is 120.043 dB.
To know more about resultant sound visit:
https://brainly.com/question/32908687
#SPJ11
A force of 5.3 N acts on a 12 kg body initially at rest. Compute the work done by the force in (a) the first, (b) the second, and (c) the third seconds and (d) the instantaneous power due to the force at the end of the third second. (a) Number ______________ Units ________________
(b) Number ______________ Units ________________
(c) Number ______________ Units ________________
(d) Number ______________ Units ________________
A force of 5.3 N acts on a 12 kg body initially at rest. Compute the work done by the force in (a) the first, (b) the second, and (c) the third seconds and (d) the instantaneous power due to the force at the end of the third second.
A force, F = 5.3 N mass, m = 12 kg Initial Velocity, u = 0
(a) The work done by the force in the first second.
The work done on a body of mass m by a force F, when the body moves a distance s in the direction of the force is given by
W = Fs
When a body is initially at rest, and a force is applied to it for time t, then the distance travelled by the body is given by:
s = (1/2)at² where a is the acceleration produced by the force.
So, the distance travelled by the body in the first second is given by:
s = (1/2)at² = (1/2) * (F/m) * t² = (1/2) * (5.3/12) * 1² = 0.22 m
So, the work done in the first second is given by:
W = Fs = 5.3 × 0.22 = 1.166 J
(b) The work done by the force in the second second.
The body is moving with uniform acceleration. So, the distance travelled by the body in the second second is given by:
s = ut + (1/2)at²where u = 0, and a = F/m.
So, the distance travelled by the body in the first second is given by:
s = ut + (1/2)at² = 0 + (1/2) * (F/m) * t² = (1/2) * (5.3/12) * 2² = 0.88 m
So, the work done in the second second is given by:
W = Fs = 5.3 × 0.88 = 4.664 J
(c) The work done by the force in the third second.
The body is moving with uniform acceleration. So, the distance travelled by the body in the third second is given by:
s = ut + (1/2)at² where u = 0, and a = F/m.
So, the distance travelled by the body in the first second is given by:
s = ut + (1/2)at² = 0 + (1/2) * (F/m) * t² = (1/2) * (5.3/12) * 3² = 1.995 m
So, the work done in the third second is given by:
W = Fs = 5.3 × 1.995 = 10.589 J
(d) The instantaneous power due to the force at the end of the third second.
The instantaneous power due to the force at the end of the third second is given by:
P = Fv where F is the force, and v is the instantaneous velocity of the body after the third second. The body is moving with uniform acceleration. So, the instantaneous velocity of the body after the third second is given by:
v = u + at = 0 + (F/m) * t = (5.3/12) * 3 = 2.2125 m/s
So, the instantaneous power due to the force at the end of the third second is given by:
P = Fv = 5.3 × 2.2125 = 11.754 W
Explore another question on work done: https://brainly.com/question/28356414
#SPJ11
An object is placed 120 mm in front of a converging lens whose focal length is 40 mm. Where is the image located?
The image is located at a distance of 180 mm from the lens.The image is formed on the opposite side of the lens.
The given converging lens is used to find the location of the image of an object placed at a distance of 120 mm in front of the lens. The focal length of the lens is 40 mm. We can calculate the distance of the image from the lens using the lens formula. The formula is given as;1/f = 1/v - 1/u
Here, f is the focal length of the lens, u is the distance of the object from the lens, and v is the distance of the image from the lens. The magnification produced by the lens can be calculated as; M = v/u
The negative sign indicates that the image is formed on the opposite side of the lens.
Using the lens formula, we have;1/f = 1/v - 1/u1/40 = 1/v - 1/1203v - v = 360v = 360/2 = 180 mm
Therefore, the image is located at a distance of 180 mm from the lens.
The image is formed on the opposite side of the lens. The image is real, inverted, and reduced. The magnification produced by the lens is;M = v/u = -180/120 = -1.5. The magnification is negative, which indicates that the image is inverted.
The answer is;Image distance, v = 180 mm.The image is real, inverted, and reduced.
Know more about converging lens here,
https://brainly.com/question/29178301
#SPJ11
A force that varies with time F-13t²-4t+3 acts on a sled of mass 13 kg from t₁ = 1.7 seconds to t₂ -3.7 seconds. If the sled was initially at rest, determine the final velocity of the sled. Record your answer with at least three significant figures.
The final velocity of the sled is approximately -6.58 m/s.
The net force F on the sled of mass m is given by the function F = -13t²-4t+3, and we are to determine its final velocity. We can use the impulse-momentum principle to solve the problem. Since the sled was initially at rest, its initial momentum p1 is zero. The impulse J of the net force F over the time interval [t₁,t₂] is given by the definite integral of F with respect to time over this interval, that is:J = ∫[t₁,t₂] F dt = ∫[1.7,3.7] (-13t²-4t+3) dt = [-13t³/3 - 2t² + 3t]t=1.7t=3.7≈ -85.522 JThe impulse J is equal to the change in momentum p2 - p1 of the sled over this interval. Therefore:p2 - p1 = J, p2 = J + p1 = J = -85.522 kg m/sSince the mass of the sled is m = 13 kg, its final velocity v2 is:v2 = p2/m ≈ -6.58 m/sHence, the final velocity of the sled is approximately -6.58 m/s.
Learn more about Momentum here,hello what is momentum?
https://brainly.com/question/18798405
#SPJ11
2) Does a rocket need the Earth, the launch pad, or the Earth's
atmosphere (or more than one of these) to push against to create
the upward net force on it? If yes to any of these, explain your
answer
"yes." Rockets need to push against the Earth's atmosphere to create an upward net force on it. Furthermore, the rocket requires a launch pad to stay in position while building up pressure.
The earth's atmosphere is necessary for the rocket to push against. The gases that make up the atmosphere exert pressure on everything in it, including rockets. For the rocket to move upwards, it needs to create an upward force that is larger than the force of gravity pulling it downwards. This upward force can be created by burning fuel and expelling the gases through the nozzle at the bottom of the rocket. The expelled gases push against the atmosphere, generating an equal and opposite reaction that pushes the rocket upwards.The launch pad is equally crucial as it provides the rocket with a firm base while it builds up pressure. When the rocket engines are ignited, a large amount of energy is released, resulting in a powerful explosion. The rocket needs to be anchored to the ground to avoid being pushed back or toppled over by the force of the blast. It is why launch pads are specially designed with massive concrete and steel structures that keep the rocket in place until it can lift-off safely.
A rocket requires the Earth's atmosphere and a launch pad to push against to create an upward net force. Without these two, the rocket cannot take off or achieve its desired altitude.
To know more about atmosphere visit:
brainly.com/question/32274037
#SPJ11
Two objects of masses 25 kg and 10 kg are connected to the ends of a rigid rod (of negligible mass) that is 70 cm long and has marks every 10 cm, as shown. Which point represents the center of mass of the sphere-rod combination? 1. F 2. E 3. G 4. J 5. A 6. H 7. D 8. C 9. B
The center of mass of the sphere-rod combination will be at point G,
As per the given conditions in the question. This is because the center of mass is the point where the two masses can be considered as concentrated, and it lies at the midpoint of the rod.Let us calculate the center of mass mathematically:For the sphere of mass 25 kg, the distance of its center from the midpoint of the rod (which is the center of mass of the system) is given by 6 x 10 = 60 cm.
For the sphere of mass 10 kg, the distance of its center from the midpoint of the rod (which is the center of mass of the system) is given by 3 x 10 = 30 cmBy definition, the center of mass is given by the formula:$$\bar{x} = \frac{m_1x_1+m_2x_2}{m_1+m_2}$$.
Where m1 and m2 are the masses of the two objects, and x1 and x2 are their distances from a reference point. In this case, we can take the midpoint of the rod as the reference point.Using the above formula, we get:$$\bar{x} = \frac{(25\ kg)(60\ cm)+(10\ kg)(30\ cm)}{25\ kg+10\ kg}$$$$\bar{x} = \frac{1500\ kg\ cm}{35\ kg}$$$$\bar{x} = 42.86\ cm$$Thus, the center of mass of the system is at a distance of 42.86 cm from the left end of the rod, which is point G. Therefore, the answer is 3. G.
Learn more about mass here,
https://brainly.com/question/86444
#SPJ11
Determine the inductance L of a 0.40-m-long air-filled solenoid 2.6 cm in diameter containing 8300 loops. Express your answer using two significant figures. * Incorrect; Try Again; One attempt remaining A 18 - en-diameter crevlar locp of wee is placed in th 0 53.I magrietc beid When the siane of the locp is perperidiulaf ta the foid ines, what is the magnetec fix through the loop? Express your answer to fwo significant figures and include the appropriate units. Part ⇒ Nor this situation? Express your answer using fwo significant figures. What is the maynic fux trieough the loop at this angle? Express your answer to two tipnificant figures and include the appropriate units.
The inductance of the air-filled solenoid is 0.009 H (henries). The magnetic flux through the loop when it is perpendicular to the magnetic field is 0.28 T (teslas). At an angle, the magnetic flux through the loop will be less than 0.28 T.
The inductance of a solenoid can be calculated using the formula L = (μ₀ * N² * A) / l, where μ₀ is the permeability of free space (4π × 10^-7 T·m/A), N is the number of loops, A is the cross-sectional area of the solenoid, and l is the length of the solenoid. Plugging in the given values, we have L = (4π × 10^-7 T·m/A * 8300² * π * (0.026 m / 2)²) / 0.40 m ≈ 0.009 H.
When the loop is perpendicular to the magnetic field, the magnetic flux through the loop can be calculated using the formula Φ = B * A, where B is the magnetic field strength and A is the area of the loop. Plugging in the given values, we have Φ = 0.53 T * π * (0.026 m / 2)² ≈ 0.28 T.
When the loop is at an angle to the magnetic field, the magnetic flux through the loop will be less than 0.28 T. This is because the component of the magnetic field perpendicular to the loop's surface decreases as the angle increases, resulting in a decrease in the magnetic flux. The exact value of the magnetic flux will depend on the angle between the loop and the magnetic field, but it will always be less than 0.28 T.
Learn more about magnetic field here:
https://brainly.com/question/19542022
#SPJ11
A wave traveling along a string is described by f(x, t) = a sin(abx + qt), + with a = 40 mm , b =0.33 m-%, and q = 10.47 s-1. Part A Calculate the amplitude of the wave. Express your answer with the appropriate units. Calculate the wavelength of the wave. Express your answer with the appropriate units. Calculate the period of the wave. Express your answer with the appropriate units.Calculate the speed of the wave. Express your answer with the appropriate units.Compute the y component of the displacement of the string at x = 0.500 m and t = 1.60 s. Express your answer with the appropriate units.
the amplitude of the wave is 40 mm, the wavelength of the wave is 18.85 m, the period of the wave is 0.601 s, the speed of the wave is 6 m/s, and the y component of the displacement of the string at x = 0.500 m and t = 1.60 s is 33.77 mm.
The given function is: f(x, t) = a sin(abx + qt), + where a = 40 mm, b = 0.33 m-%, and q = 10.47 s-1.
Calculation of the amplitude of the wave: The amplitude of the wave is given by the coefficient of sin.
It is equal to 40 mm. Calculation of the wavelength of the wave:
The formula for the wavelength of the wave is given as:λ = 2π / b = 6π m = 18.85 m.
Calculation of the period of the wave: The formula for the period of the wave is given as: T = 2π / q = 0.601 s.
Calculation of the speed of the wave: The formula for the speed of the wave is given as:v = λf = λ(q/2π) = 6m/s.
Calculation of the y component of the displacement of the string at x = 0.500 m and t = 1.60 s:The given function is: f(x, t) = a sin(abx + qt) = 40 sin[(0.33π)(0.5) + (10.47)(1.6)] = 33.77 mm.
Hence, the amplitude of the wave is 40 mm, the wavelength of the wave is 18.85 m, the period of the wave is 0.601 s, the speed of the wave is 6 m/s, and the y component of the displacement of the string at x = 0.500 m and t = 1.60 s is 33.77 mm.
Learn more about wavelength here:
https://brainly.com/question/31322456
#SPJ11
Find the system output y(t) of a linear and time-invariant system with the input x(t) and the impulse response h(t) as shown in Figure 1. Sketch y(t) with proper labelling. Figure 1 (13 Marks) (b) The message signal m(t)=5cos(2000πt) is used to modulate a carrier signal c(t)=4cos(80000πt) in a conventional amplitude modulation (AM) scheme to produce the AM signal, x AM
(t), in which the amplitude sensitivity factor of the modulator k a
is used. (i) Express the AM signal x AM
(t) and find its modulation index. (ii) Determine the range of k a
for the case of under-modulation. (iii) Is under-modulation or over-modulation required? Why? (iv) Determine the bandwidths of m(t) and x AM
(t), respectively.
(i)The modulation index of the given signal is 5ka/2000. (ii)For under modulation: modulation index ≤ 1/3 . (iv) The bandwidths of m(t) and xAM(t) are 2000 Hz and 1.64 MHz (approx), respectively.
a)System input x(t):y(t)=5∫0tx(τ)h(t-τ)dτ=5∫0t5τe^(-2τ)u(t-τ)dτ=25∫0tτe^(-2τ)u(t-τ)dτ. Use integration by parts to find y(t):(y(t)=25∫0tτe^(-2τ)u(t-τ)dτ=25[-(1/2)τe^(-2τ)u(t-τ)+[(1/2)e^(-2τ)]_0^t-∫0(t) -1/2e^(-2τ)dτ)] =(t/2)e^(-2t)-25[(1/2)e^(-2t)-1/2]+25/2≈(t/2)e^(-2t)+11.25.
b)(i) Expression of AM signal, xAM(t) is:xAM(t)=(4+5ka cos(2000πt))cos(80000πt)Modulation index is given as m=kafm/fcm=5ka/2000.
(ii) For under-modulation: modulation index ≤ 1/3i.e., 5ka/2000 ≤ 1/3ka ≤ 0.04.
(iii) Over-modulation is required. For the full utilization of the channel bandwidth and avoiding the distortion of message signal.
(iv) The bandwidths of m(t) and xAM(t) are given as: Bandwidth of m(t) = fm = 2000 Hz. Bandwidth of xAM(t) = 2(fm + fc) = 2(2000+80000) = 1.64 MHz (approx)Therefore, the bandwidths of m(t) and xAM(t) are 2000 Hz and 1.64 MHz (approx), respectively.
Let's learn more about AM signal:
https://brainly.com/question/30562023
#SPJ11
What Determine The Maximum Theoretical Efficiency Of A Wind Turbine. Briefly Explain The Reason For This Limit And State The Value Of Maximum Efficiency. Describe Onshore And Offshore Wind Farm Technology. Clearly State Advantages And Disadvantages Of Each Technology. Describe - A: Active Pitch-Control B:
What determine the maximum theoretical efficiency of a wind turbine. Briefly explain the reason for this limit and state the value of maximum efficiency.
Describe onshore and offshore Wind farm technology. Clearly state advantages and disadvantages of each technology.
Describe -
A: Active pitch-control
B: Passive stall-control
C: Active stall-control
The maximum theoretical efficiency of a wind turbine is determined by the Betz limit. The limit is 59.3% (i.e. the maximum theoretical efficiency of a wind turbine can only reach 59.3% of the energy that would be extracted if all the air passing through the turbine blades was captured and converted into energy).
The Betz limit is due to the conservation of mass and momentum of the air as it passes through the blades of the turbine. Any excess energy extracted would cause the air to slow down too much and back up, causing turbulence and reducing the effectiveness of the blades. Therefore, to maximize efficiency, turbines are designed to operate as close as possible to the Betz limit. Onshore wind farm technology involves installing turbines on land, often in areas with strong and consistent wind patterns.
Advantages of onshore wind farms include lower installation and maintenance costs, easier access to the grid, and less impact on marine life. Disadvantages include visual and noise pollution, and potential conflict with land use (e.g. agriculture). Offshore wind farm technology involves installing turbines in bodies of water, often further from shore in deeper waters. Advantages of offshore wind farms include stronger and more consistent wind patterns, less visual and noise pollution, and more potential for expansion.
Disadvantages include higher installation and maintenance costs, limited access to the grid, and potential impact on marine life.
A. Active pitch control involves adjusting the angle of the turbine blades to optimize the amount of energy extracted from the wind. This can improve the efficiency of the turbine, especially in variable wind conditions.
B. Passive stall-control involves allowing the blade to stall (i.e. lose lift) at high wind speeds, reducing the amount of energy extracted from the wind to prevent damage to the turbine. This can limit the efficiency of the turbine, especially in low wind conditions.
C. Active stall-control involves adjusting the pitch angle of the blade to stall the blade at high wind speeds, similar to passive stall control, but with more control over the stall point. This can improve the efficiency of the turbine, especially in variable wind conditions.
know more about Active pitch control
https://brainly.com/question/30547641
#SPJ11
according to : y =\lambdaD/d
the approximate width of the central bright fringe
from a single slit diffraction
1. will increase with increasing wave length
2. will increase will increasing slit width
3. both of the above
4. does not depend on wave length or slit width
According to the equation y = λD/d, the approximate width of the central bright fringe from a single slit diffraction will depend on both the wavelength of light used and the width of the slit itself.
Therefore, the correct option is option c. This means that the width of the central bright fringe will increase with increasing wavelength, as well as with increasing slit width.
The equation y = λD/d is used to calculate the position of the nth bright fringe in a single slit diffraction pattern, where y is the distance from the center of the pattern to the fringe, λ is the wavelength of light used, D is the distance between the slit and the screen, and d is the width of the slit.
As per the equation, the width of the central bright fringe (n = 0) is given by the formula y0 = λD/d. Therefore, it can be inferred that the width of the central bright fringe will increase as the wavelength of light used increases, as well as with an increase in the width of the slit.
To know more about slits visit:
https://brainly.com/question/31551061
#SPJ11
An electron has a rest mass m 0
=9.11×10 −31
kg. It moves with a speed v=0.700c. The speed of light in a vacuum c=3.00×10 8
m/s. An electron has a rest mass m 0
=9.11×10 −31
kg. It moves with a speed v=0.700c. The speed of light in a vacuum c=3.00×10 8
m/s. m/s. - Part A - Find its relativistic mass. Use scientific notations, format 1.234 ∗
10 n
. Unit is kg - Part B - What is the total energy E of the electron? Use scientific notations, format 1.234 ∗
10 n
. Unit is Joules. What is the relativistic kinetic energy KE of the electron? Use scientific notations, format 1.234 ∗
10 n
. Unit is Joules.
The relativistic mass of the electron is approximately 1.129 * 10^-30 kg. The total energy E of the electron is about 1.017 * 10^-17 Joules, and its relativistic kinetic energy is approximately 1.717 * 10^-18 Joules.
In Part A, using the formula for relativistic mass m = m0 / sqrt(1 - v^2/c^2), where m0 is the rest mass, v is the velocity, and c is the speed of light, we calculate the relativistic mass of the electron. For Part B, the total energy E is determined by E = mc^2, where m is the relativistic mass and c is the speed of light. The relativistic kinetic energy is calculated as KE = E - m0c^2, where m0 is the rest mass of the electron, and E is the total energy. These calculations demonstrate how an object's mass and energy change at relativistic speeds, according to Einstein's theory of relativity.
Learn more about relativistic mass here:
https://brainly.com/question/32174220
#SPJ11
A virtual image of an object formed by a converging lens is 2.33mm tall and located 7.28cm before the lens. The magnification of the lens is 2.16. Determine the focal length of the lens (in cm).
A virtual image of an object formed by a converging lens is 2.33mm tall and located 7.28cm before the lens. Therefore, the focal length of the converging lens is -8.514 cm.
Given that virtual image of an object formed by a converging lens is 2.33 mm tall and located 7.28 cm before the lens and the magnification of the lens is 2.16.
To determine the focal length of the lens (in cm).Formula used: magnification = -image height/object height magnification = v/u
where, v = distance of image from the lens, u = distance of object from the lens
Using the above formula, we can determine the distance of image from the lens as:u = -v/magnification , v = u x magnificationGiven that,object height, h0 = 0.00233 m
image height, hi = 0.00233 mm x 10^-3 = 2.33 x 10^-6 m , distance of the object from the lens, u = -7.28 cm = -0.0728 m, distance of the image from the lens, v = ?magnification, m = 2.16Putting these values in the formula above: v = u x magnification
v = -0.0728 x 2.16v = -0.156768 m
We know the formula for the focal length is given as:1/f = 1/v - 1/uwhere,f = focal length of the lens
Putting the values in this formula,1/f = 1/-0.156768 - 1/-0.0728Solving for f,f = -0.08514 m = -8.514 cm
Therefore, the focal length of the converging lens is -8.514 cm.
Learn more about focal length here:
https://brainly.com/question/11870211
#SPJ11
A glass bottle with a volume of 100 cm³ full with fluid has a relative density of 1.25. If the total mass is 301.7 g and the mass density of glass bottle is 2450 kg/m³, determine: i. Glass bottle mass ii. Glass bottle volume
The mass of the glass bottle can be determined by subtracting the mass of the fluid from the total mass. The volume of the glass bottle can be calculated using the mass density of the glass bottle.
i. The mass of the glass bottle can be calculated by subtracting the mass of the fluid from the total mass:
Glass bottle mass = Total mass - Fluid mass = 301.7 g - (100 cm³ * 1.25 g/cm³) = 301.7 g - 125 g = 176.7 g.
ii. The volume of the glass bottle can be determined by dividing the mass of the glass bottle by its mass density:
Glass bottle volume = Glass bottle mass / Glass bottle mass density = 176.7 g / (2450 kg/m³ * 1000 g/kg) = 0.072 m³ or 72 cm³.
Learn more about mass here;
https://brainly.com/question/86444
#SPJ11
The temperature is -8 °C, the air pressure is 85 kPa, and the vapour pressure is 0.2 kPa.
Calculate the following please and give answer with numbers
a)dew-point temperature?
b)relative humidity?
c) absolute humidity?
d) mixing ratio?
e)saturation mixing ratio?
f)Use your answers to d) and e) to recalculate the relative humidity.
a) dew-point temperature is -17.4°C.
b) relative humidity is 32.4% .
c) absolute humidity is 0.33 g/m³.
d) mixing ratio is 0.00183.kg/kg.
e) saturation mixing ratio is 0.00217 kg/kg.
f) Using the answers of d) and e), the relative humidity is recalculated as 84.4%.
Explanation:Given data: Temperature, T = -8°CPressure, P = 85kPaVapour pressure, e = 0.2 kPaStep 1: Calculation of the Saturation Pressure (es)We will use the formula: es = 6.11 * 10^(7.5T/ (237.7+T)) es = 6.11 * 10^(7.5(-8)/ (237.7-8)) es = 0.733 kPaStep 2: Calculation of the Relative Humidity(RH)RH = (e/es)*100RH = (0.2/0.733)*100RH = 27.27%Step 3: Calculation of the Dew Point Temperature (Td)We will use the formula: Td = (237.7 * log10((e/6.11))) / (log10(e/6.11)-7.5)) Td = (237.7 * log10((0.2/6.11))) / (log10(0.2/6.11)-7.5)) Td = -17.4°CStep 4: Calculation of the Mixing Ratio (w)We will use the formula: w = 0.622 * (e / (P-e)) w = 0.622 * (0.2 / (85-0.2)) w = 0.00183 kg/kgStep 5: Calculation of the Saturation Mixing Ratio (ws)We will use the formula: ws = 0.622 * (es / (P-es)) ws = 0.622 * (0.733 / (85-0.733)) ws = 0.00217 kg/kgStep 6: Calculation of the Absolute Humidity (A)We will use the formula: A = (w * P) / (0.287 * (T+273.15)) A = (0.00183 * 85) / (0.287 * (-8+273.15)) A = 0.33 g/m³Step 7: Calculation of the new Relative Humidity(RH)RH = (w/ws)*100RH = (0.00183/0.00217)*100RH = 84.4%Therefore, the values of the given parameters are as follows:a) dew-point temperature is -17.4°C.
b) relative humidity is 32.4%.
c) absolute humidity is 0.33 g/m³.
d) mixing ratio is 0.00183.kg/kg.
e) saturation mixing ratio is 0.00217 kg/kg.
f) Using the answers of d) and e), the relative humidity is recalculated as 84.4%.
Learn more about humidity
https://brainly.com/question/20490622
#SPJ11
To calculate the dew-point temperature, use the equation Td = (237.3 * (ln(e / 6.112))) / (17.27 - (ln(e / 6.112))). To calculate relative humidity, use RH = (e / es) * 100%, where es = 6.112 * exp((17.67 * T) / (T + 243.5)). Absolute humidity can be calculated using AH = (e * 1000) / (R * T), and mixing ratio can be calculated with MR = (0.622 * e) / (p - e). Saturation mixing ratio can be determined with MRs = (0.622 * es) / (p - es). To recalculate relative humidity using mixing ratio and saturation mixing ratio, use RH = (MR / MRs) * 100%.
a) To calculate the dew-point temperature, we need to know the air temperature and the vapor pressure. The dew-point temperature is the temperature at which air becomes saturated with water vapor, causing condensation to occur. We can use the equation for dew-point temperature:
Td = (237.3 * (ln(e / 6.112))) / (17.27 - (ln(e / 6.112)))
Using the given vapor pressure of 0.2 kPa, we substitute this value into the equation:
Td = (237.3 * (ln(0.2 / 6.112))) / (17.27 - (ln(0.2 / 6.112)))
Calculating this equation will give us the dew-point temperature.
b) Relative humidity can be calculated using the equation:
RH = (e / es) * 100%
Where e is the vapor pressure and es is the saturation vapor pressure at the given temperature. The saturation vapor pressure can be determined using the equation:
es = 6.112 * exp((17.67 * T) / (T + 243.5))
Where T is the air temperature. Substitute the given values into these equations to calculate the relative humidity.
c) Absolute humidity is the mass of water vapor per unit volume of air. It can be calculated using the equation:
AH = (e * 1000) / (R * T)
Where e is the vapor pressure, R is the specific gas constant for water vapor (461.5 J/(kg·K)), and T is the air temperature. Substitute the given values into this equation to calculate the absolute humidity.
d) Mixing ratio is the mass of water vapor per unit mass of dry air. It can be calculated using the equation:
MR = (0.622 * e) / (p - e)
Where e is the vapor pressure and p is the total air pressure. Substitute the given values into this equation to calculate the mixing ratio.
e) Saturation mixing ratio is the maximum mixing ratio that air can hold at a given temperature. It can be calculated using the equation:
MRs = (0.622 * es) / (p - es)
Where es is the saturation vapor pressure. Substitute the given values into this equation to calculate the saturation mixing ratio.
f) To recalculate the relative humidity using the mixing ratio and saturation mixing ratio, we can use the equation:
RH = (MR / MRs) * 100%
Substitute the calculated values for mixing ratio and saturation mixing ratio into this equation to recalculate the relative humidity.
These calculations will provide the answers you need, ensuring you have a comprehensive understanding of the concepts.
Learn more about dew-point temperature
https://brainly.com/question/33457834
#SPJ11
A toy car that is 0.12 m long is used to model the actions of an actual car that is 6 m long.
A toy car that is 0.12 m long is used to model the actions of an actual car that is 6 m long. So, The acceleration of the actual car is 1515.15 m/s².
The solution to this question can be achieved through the use of the equation: F = ma Where F is force, m is mass, and a is acceleration.
Step 1: Calculating the mass of the toy car using the ratio of lengths m1/m2 = l1/l2, where m1 and m2 are the masses of the toy car and actual car, and l1 and l2 are their respective lengths.
Rearranging, we have:m1 = (l1/l2)m2 = (0.12 m)/(6 m) m2 = 0.02 m2
Step 2: Using the equation, F = ma, we can determine the mass of the toy car: F = ma2 N = (0.02 m2) a a = 2 N / 0.02 m2 = 100 m/s²
Step 3: Using the same force of 5 N, the acceleration of the actual car can be calculated:F = ma5 N = ma m = m2/l2 m = 0.02 m2 / 6 m = 0.0033 kg a = F/m a = 5 N / 0.0033 kg = 1515.15 m/s²
Therefore, the acceleration of the actual car is 1515.15 m/s².
For more questions on acceleration
https://brainly.com/question/460763
#SPJ8
The probable question may be:
A toy car that is 0.12 m long is used to model the actions of an actual car that is 6 m long. The toy car is pushed with a force of 5 N, causing it to accelerate at a rate of 2 m/s². Assuming the same force is applied to the actual car, calculate the acceleration of the actual car.
For the circuit in Figure 1, calculate: a) Pod b) Pie c) %n d) Power dissipated by both output transistors. Marking Scheme: 1. Calculation using correct Formulae 2. Simulation using any available software V₂ 18 V. 100 F 100 R₁ 10022 +Vcc (+40V) G R₂ 100 (2 R₂
The values of a) Pod is 8 W, b) Pie is 2 W, c) %n is 150% and d) Power dissipated by both output transistors is 16 W.
a) Let's first calculate the Pod for the given circuit.
Pod is the power dissipated by one output transistor when the output is at zero or maximum voltage.
For the output at maximum voltage, output resistance R1 is in parallel with R2 and for the output at minimum voltage, output resistance R2 is in parallel with R1.
Pod = (Vcc/2)^2 / (R1 || R2)
Pod = (20)^2 / 50 = 8 W
b) Now let's calculate the value of Pie.
Pie is the power dissipated by one output transistor when the output is at half of maximum voltage.
Pie = (Vcc/4)^2 / (R1 || R2)
Pie = (10)^2 / 50 = 2 W
c) Let's calculate the value of %n.
%n is the efficiency of the amplifier.
It is given by
%n = Pout / Pdc
Where Pout is the output power of the amplifier and Pdc is the power supplied by the DC source to the amplifier.
Using the values of Pod and Pie,
Pout = Pod - Pie = 8 - 2 = 6 W
Pdc = Vcc * Icq
where
Icq is the collector current of the transistor.
Let's calculate the value of Icq.
Icq = Vcc / (R1 + R2)
Using values of Vcc, R1, and R2 in the above formula
Icq = 20 / 100 = 0.2 A
Now, using values of Vcc and Icq in the above formula
Pdc = Vcc * Icq = 20 * 0.2 = 4 W
Thus,%n = 6 / 4 = 1.5 or 150%
d) Now let's calculate the power dissipated by both output transistors.
Power dissipated by both output transistors is equal to 2 * Pod.
Let's calculate the value of power dissipated by both output transistors.
Using the value of Pod,
Power dissipated by both output transistors = 2 * Pod = 2 * 8 = 16 W
Therefore, the values of a) Pod is 8 W, b) Pie is 2 W, c) %n is 150% and d) Power dissipated by both output transistors is 16 W.
Learn more about power :
https://brainly.com/question/11569624
#SPJ11
2.17 Compute and plot the solar irradiance at the top of the earth's atmosphere emitted from temperatures of 5000,5500 , and 6000 K. Compare your results with those presented in Figs. 2.9 and 2.10.
The
solar irradiance
emitted from temperatures of 5000 K, 5500 K, and 6000 K at the top of the earth's atmosphere can be computed using the Stefan-Boltzmann law which states that the total radiant heat energy (J/s) emitted by a surface is proportional to the fourth power of its absolute temperature (K).
Mathematically, the law can be expressed as;E = σT^4where E is the total emitted energy, T is the absolute temperature in Kelvin, and σ is the
Stefan-Boltzmann constant
(5.67 × 10^−8 Wm^−2 K^−4).Thus, at temperatures of 5000 K, 5500 K, and 6000 K, the solar irradiance at the top of the earth's atmosphere can be calculated as follows;E_5000 = σT^4 = 5.67 × 10^−8 × (5000)^4 = 3.89 × 10^7 Wm^−2E_5500 = σT^4 = 5.67 × 10^−8 × (5500)^4 = 5.83 × 10^7 Wm^−2E_6000 = σT^4 = 5.67 × 10^−8 × (6000)^4 = 8.45 × 10^7 Wm^−2To compare the results obtained with those presented in Figures 2.9 and 2.10, the plots of the spectral solar irradiance as a function of wavelength for the three
temperatures
should be generated. The results can be compared based on the
wavelength
ranges and peak irradiance values obtained in the two figures.
Learn more about
solar irradiance
https://brainly.com/question/12974688
#SPJ11
By comparing the computed values with the figures, we can analyze the differences and similarities in the solar irradiance at different temperatures.
To compute the solar irradiance at the top of the Earth's atmosphere emitted from temperatures of 5000, 5500, and 6000 K, we can use the Stefan-Boltzmann law, which states that the power radiated by a black body is proportional to the fourth power of its temperature.
The formula for the power radiated by a black body is given by [tex]\rm \(P = \sigma \cdot A \cdot T^4\)[/tex], where P is the power radiated, [tex]\(\sigma\)[/tex] is the Stefan-Boltzmann constant (approximately [tex]\rm \(5.67 \times 10^{-8} \, \text{W/m}^2\text{K}^4\)), \(A\)[/tex] is the surface area of the black body, and T is the temperature in Kelvin.
To compute the solar irradiance, we need to know the surface area of the Earth. Assuming the Earth to be a perfect sphere, its surface area can be calculated using the formula [tex]\(A = 4\pi R^2\)[/tex], where R is the radius of the Earth.
Substituting the values into the formula, we can calculate the solar irradiance for each temperature:
For [tex]\(5000 \, \text{K}\)[/tex]:
Solar irradiance [tex]\rm \(= \sigma \cdot A \cdot T^4\)[/tex]
Substituting the values, we get:
Solar irradiance [tex]\(= 5.67 \times 10^{-8} \cdot (4\pi R^2) \cdot (5000^4)\)[/tex]
Similarly, we can calculate the solar irradiance for temperatures of [tex]\(5500 \, \text{K}\) and \(6000 \, \text{K}\)[/tex].
To compare the results with Figures 2.9 and 2.10, we need to plot the computed solar irradiance values against the wavelength of the radiation. These figures show the solar irradiance spectrum at the top of the Earth's atmosphere for different wavelengths.
Learn more about solar irradiance
https://brainly.com/question/12974688
#SPJ11
A 4.0-cm tall object is placed 60 cm away from a converging lens of focal length 30 cm. What are the nature and location of the image? The image is real, 2.5 cm tall, and 30 cm from the lens on the same side as the object. virtual, 4.0 cm tall, and 60 cm from the lens on the same side as the object. virtual, 2.5 cm tall, and 30 cm from the lens on the side opposite the object. real, 4.0 cm tall, and 60 cm from the lens on the side opposite the object.
The image formed by a converging lens when a 4.0-cm tall object is placed 60 cm away from it is real, 2.5 cm tall, and located 30 cm from the lens on the same side as the object.
According to the given information, the object is placed 60 cm away from the converging lens, which has a focal length of 30 cm. Since the object is placed beyond the focal point of the lens, a real image is formed on the same side as the object.
Using the lens formula, 1/f = 1/v - 1/u, where f is the focal length, v is the image distance, and u is the object distance, we can calculate the image distance. Plugging in the values, we have 1/30 = 1/v - 1/60. Solving this equation gives us v = 30 cm.The magnification formula, M = -v/u, where M is the magnification, can be used to determine the magnification of the image. Plugging in the values, we have M = -(30/60) = -0.5. This indicates that the image is smaller than the object.
Since the image distance is positive and the magnification is negative, we can conclude that the image is real, 2.5 cm tall (half the height of the object), and located 30 cm from the lens on the same side as the object.
Learn more about converging lens here:
https://brainly.com/question/29178301
#SPJ11
The switch is closed for a long time. It opens at t-0. i) Find i, (0+) and v₂ (0+) [3 pts] X1=0 692 12 V 2H 0.4 F For t > 0, what kind of system response does the series RLC circuit produce for i(t)? (Underdamped, overdamped, critically damped). Also, express the form of the solution. Find di(0*) and dv (0*) dt dt Iz(t) 492 :ve(t)
The current in the series RLC circuit is given by the equation i(t) = X1 * exp(-t/(2RC)) * sin(√(1/(LC) - (1/(2RC))^2)t). The system response is underdamped, indicating oscillatory behavior due to the presence of the sinusoidal term in the equation.
[tex]i(0∗)[/tex] represents the current at time
[tex]�=0+t=0 +[/tex]
(just after the circuit switch is closed).
[tex]��(0∗)��dtdv(0 ∗ )[/tex]
represents the derivative of voltage with respect to time at
[tex]�=0+t=0 + .��(�)=492[/tex]
[tex]Iz(t)=492[/tex] (no units provided) represents a variable or function representing the current source.
[tex]��(�)v e[/tex]
(t) represents the voltage across the capacitor as a function of time.
The current in the series RLC circuit is given by the equation:
[tex]\[i(t) = \frac{X1}{L} \exp\left(-\frac{R}{2L}t\right) \sin\left(\sqrt{\left(\frac{1}{LC}\right) - \left(\frac{R}{2L}\right)^2}t\right)\][/tex]
where \(X1\) is the initial voltage across the capacitor, \(R\) is the resistance, \(L\) is the inductance, \(C\) is the capacitance, and \(t\) is time. The system response of the circuit is underdamped.
The expression describes the behavior of the current over time in the circuit.
We are given the following values:[tex]X1=0.69212 V, R = 2 Ω, L = 0.4 H, C = 1[/tex] F and i(t) is the current. Using KVL,KVL equation around the loop :[tex]`v(t) = L(di(t)/dt) + Ri(t) + (1/C)∫i(t)dt[/tex] `Differentiate both sides with respect to time, [tex]t`(dv(t)/dt) = L(d²i(t)/dt²) + R(di(t)/dt) + i(t)/C`[/tex]. Now, we have to find the value of i(0+) and v2(0+).Given, X1 = 0.69212 V. Also, at t = 0-, switch is closed, hence no current is flowing through the circuit.
Hence, [tex]X1 = v(0-) = v(0+)[/tex] .Now, for the current i(t), let us take the Laplace transform of the above equation,[tex]`(sV(s) - V(0)) = L(s²I(s) - si(0) - i'(0)) + RI(s) + I(s)/(sC)`[/tex] Where, [tex]V(0)[/tex] is the initial voltage across the capacitor. Similarly, let's take the Laplace transform of the current i(t)[tex],`V(s)/s = L(sI(s) - i(0)) + RI(s) + I(s)/sC`[/tex] Solving the above equations, [tex]`I(s) = (V(s) - sL(i(0) + V(0)))/(s²L + R.s + 1/C)`[/tex]Using partial fraction expansion, [tex]I(s) = [((V(s) - sL(i(0) + V(0)))/(sL + R/2 + √((R/2)² - L/C))) - ((V(s) - sL(i(0) + V(0)))/(sL + R/2 - √((R/2)² - L/C)))]/√((R/2)² - L/C)`[/tex]On taking the inverse Laplace transform of the above equation, the expression for[tex]i(t)[/tex]becomes,`i(t) =[tex](X1/L) exp(-(R/2L)t) sin(√((1/LC) - (R/2L)²)t)[/tex]`On analyzing the above equation, we can say that the system response is "underdamped". As the switch is closed for a long time, the initial condition i(0*) can be considered to be zero. [tex]dv(0*)/dt = (Iz - i(0+))/C.[/tex]
Now, `[tex]di(0*)/dt = d/dt [Iz - i(0+)/C]` = - d/dt [i(0+)/C] = 0.[/tex] So, [tex]di(0*)/dt = 0.[/tex] Hence, [tex]i(0*) = i(0+) = 0.[/tex]Thus, the system response of the series RLC circuit is "underdamped". The expression for the current i(t) is `i(t) = [tex](X1/L) exp(-(R/2L)t) sin(√((1/LC) - (R/2L)²)t)`.[/tex]
To know more about RLC circuit click here:
https://brainly.com/question/32069284
#SPJ11
A sample of blood of density 1060 kg/m ∧
3 is flowing at a velocity of 0.2 m/s through a blood vessel of radius r=0.004 m and length L=1 cm. If the flow resistance is R flow =8.1×10 ∧
5 Pa.s/m ∧
3 then the viscosity of this blood would be equal to: 4.07×10 ∧
−3Pa.S 8.14×10 ∧
−3 Pa.s 8.14×10 ∧
−2 Pa.s 4.07×10 ∧
−2 Pa.s Assume the radius of the aorta is 1.1 cm, and the average speed of blood passing * through it is v −
a=0.5 m/s. If a typical capillary has a radius of 4×10 ∧
−6 m, and there are 6×10 ∧
9 capillaries, then calculate the average speed of blood flow in the capillaries. v −c
=1.2×10 ∧
−2 m/s v −
c=3.9×10 ∧
−2 m/s v c
c=8.8×10 ∧
−4 m/s \( v_{\text {_ }} c=6.3 \times 10^{\wedge}-4 \mathrm{~m} / \mathrm{s} \)
According to Poiseuille's law,The flow resistance of a cylindrical pipe is given as,$$R_{\text {flow }}=\frac{8 \eta L}{\pi r^{4}} v$$Where,η is the viscosity of the fluid in Pa.s.L is the length of the pipe in meters.r is the radius of the pipe in meters.v is the velocity of fluid in the pipe in m/s.
Given,The density of the fluid,ρ = 1060 kg/m³Velocity of the fluid, v = 0.2 m/sRadius of the blood vessel, r = 0.004 mLength of the blood vessel, L = 1 cm = 0.01 mFlow resistance, R_flow = 8.1 × 10⁵ Pa.s/m³We need to find the viscosity of the fluid.Using Poiseuille's law, we get$$\eta=\frac{\pi r^{4} R_{\text {flow }}}{8 L v}$$.
Substituting the given values, we get,$$\eta=\frac{\pi (0.004)^{4}(8.1 \times 10^{5})}{8 \times 0.01 \times 0.2}$$$$\implies \eta=8.14 \times 10^{-3} \mathrm{Pa.s}$$Therefore, the viscosity of the blood is 8.14×10⁻³ Pa.s.Given,Radius of aorta, r_a = 1.1 cmVelocity of blood passing through it, v_a = 0.5 m/sRadius of a typical capillary, r_c = 4 × 10⁻⁶ mNumber of capillaries, N = 6 × 10⁹The flow of the blood remains the same through the capillaries.Using the principle of continuity, we have$$A_{a} v_{a}=A_{c} v_{c}$$$$\implies v_{c}=\frac{A_{a} v_{a}}{A_{c}}$$.
The area of aorta is given as, $$A_{a}=\pi r_{a}^{2}$$$$\implies A_{a}=\pi (0.011)^{2}$$The area of a typical capillary is given as, $$A_{c}=\pi r_{c}^{2}$$$$\implies A_{c}=\pi (4 \times 10^{-6})^{2}$$Substituting the given values, we get$$v_{c}=\frac{\pi (0.011)^{2}(0.5)}{\pi (4 \times 10^{-6})^{2}}$$$$\implies v_{c}=6.25 \times 10^{-4} \mathrm{m/s}$$Therefore, the average speed of blood flow in the capillaries is 6.25 × 10⁻⁴ m/s.
Learn more on viscosity here:
brainly.in/question/12690306
#SPJ11
The magnetic field flux through a circular wire is 60 Wb. The radius of the wire is duplicated over the course of 3 s. Determine the voltage that is generated in that interval.
The voltage that is generated in 3 seconds will be N × πr²/2 × (4πRB - 60 / 3) where r → r' and the given magnetic field flux through a circular wire is 60 Wb.
The magnetic field flux through a circular wire is 60 Wb.
Radius of wire is duplicated over the course of 3 seconds.i.e, Radius initially, r = R
New radius, r' = 2R
Time taken, t = 3 s
We have to find out the voltage generated in this interval.Formula to find out the voltage generatedV = N × A × (dΦ / dt)
Where, N is the number of turns A is the area of the loopd Φ is the change in magnetic flux in timet is the time taken by the change in magnetic flux to occuri.e, V = N × A × (dΦ / dt)
We have a circular wire. So, the area of the loop is,A = πr²
When radius changes, i.e, r → r',dA = πr² - πr²/2= πr²/2
So, the voltage generated will be,V = N × A × (dΦ / dt)= N × πr²/2 × [(Φ' - Φ) / t]
Here, initial flux, Φ = 60 Wb
Final flux, Φ' = Φ at t = 3 s = π(2R)²×B = π(4R²)B
Now, the voltage generated will be V = N × πr²/2 × [(Φ' - Φ) / t]= N × πr²/2 × [(π(4R²)B - 60) / 3]= N × πr²/2 × (4πRB - 60 / 3)
Therefore, the voltage that is generated in 3 seconds will be N × πr²/2 × (4πRB - 60 / 3) where r → r' and the given magnetic field flux through a circular wire is 60 Wb.
Know more about voltage here,
https://brainly.com/question/31347497
#SPJ11
An aircraft engine starts from rest; and 6 seconds later, it is rotating with an angular speed of 138 rev/min. If the angular acceleration is constant, how many revolutions does the propeller undergo during this time? Give your answer to 2 decimal places
During this time, the propeller undergoes approximately 6.95 revolutions.
Initial angular velocity, ω1 = 0
Final angular velocity, ω2 = 138 rev/min
Time taken, t = 6 seconds
To find the number of revolutions the propeller undergoes, we need to calculate the angular displacement.
We can use the equation:
θ = ω1*t + (1/2)αt²
Since the initial angular velocity is 0, the equation simplifies to:
θ = (1/2)αt²
We know that the final angular velocity in rev/min can be converted to rad/s by multiplying it by (2π/60), and the final angular velocity in rad/s is given by:
ω2 = 138 rev/min * (2π/60) rad/s = 14.44 rad/s
By substituting the provided data into the equation, we can determine the result:
θ = (1/2)α(6)²
To find α, we can use the equation:
α = (ω2 - ω1) / t
By substituting the provided data into the equation, we can determine the result:
α = (14.44 - 0) / 6 = 2.407 rad/s²
Now we can calculate the angular displacement:
θ = (1/2)(2.407)(6)² = 43.63 radians
To calculate the number of revolutions, we divide the angular displacement by 2π:
n = θ / (2π) = 43.63 / (2π) ≈ 6.95 revolutions
Therefore, during this time, the propeller undergoes approximately 6.95 revolutions.
Learn more about revolutions at: https://brainly.com/question/16533738
#SPJ11
An old fashioned computer monitor accelerates electrons and directs them to the screen in order to create an image.
If the accelerating plates are 0.958 cmcm apart, and have a potential difference of 2.60×104 VV , what is the magnitude of the uniform electric field between them?
The magnitude of the uniform electric field between the accelerating plates is approximately 2.71 × [tex]10^6[/tex] V/m.
The magnitude of the uniform electric field between the accelerating plates can be determined using the formula E = V/d, where E is the electric field, V is the potential difference, and d is the distance between the plates.
In this case, the electric field magnitude is obtained by dividing the potential difference of 2.60×104 V by the plate separation distance of 0.958 cm.
The magnitude of the electric field (E) between the accelerating plates can be found using the formula E = V/d, where V is the potential difference between the plates and d is the distance between the plates.
In this case, the given potential difference is 2.60×104 V and the plate separation distance is 0.958 cm.
However, it is important to note that the distance should be converted to meters to ensure consistency with the SI units used for electric field.
Converting 0.958 cm to meters, we have:
d = 0.958 cm = 0.958 × 10^(-2) m
Now, we can substitute the values into the formula:
E = V/d = (2.60×104 V) / (0.958 × 10^(-2) m)
Simplifying the expression, we divide the numerator by the denominator:
E ≈ 2.71 × [tex]10^6[/tex] V/m
Therefore, the magnitude of the uniform electric field between the accelerating plates is approximately 2.71 × [tex]10^6[/tex] V/m.
Learn more about electric field here:
https://brainly.com/question/30544719
#SPJ11
Instructions: Do the following exercises. Remember to do ALL the steps, write the final result in Scientific Notation, if applicable and round to two decimal places. 1. Determine the minimum force needed to stop a 15.89 kg object that is accelerating at a rate of 2.5 m/s².
2. The third floor of a house is 8.0 m above the street. How much work must be done to raise a 150 kg refrigerator up to that floor? 3. How much work is done to lift a 180.0-kg box a vertical distance of 32.0 m?
The minimum force needed to stop a 15.89 kg object that is accelerating at a rate of 2.5 m/s² is 39.725 N. The work done to raise a 150 kg refrigerator up to the third floor, which is 8.0 m above the street, is 11760 J. The work done to lift a 180.0 kg box a vertical distance of 32.0 m is 565248 J.
The terms "force" and "work" are important concepts in physics. A force is any kind of push or pull that can cause a change in an object's motion. Work is done when an object moves because of a force applied to it. In order to answer the given question, we must first learn the formulas to calculate force and work.
The formula to calculate force is:
F = m × a
The formula to calculate work is:
W = F × d × cosθ
where W is the work done, F is the force applied, d is the distance moved, and θ is the angle between the force and the direction of motion.Now, let's answer each question one by one:
1. Determine the minimum force needed to stop a 15.89 kg object that is accelerating at a rate of 2.5 m/s².
F = m × a
F = 15.89 kg × 2.5 m/s²
F = 39.725 N
The minimum force needed to stop the object is 39.725 N.
2. W = F × d × cosθ
First, let's calculate the force needed to raise the refrigerator.
F = m × g
F = 150 kg × 9.8 m/s²
F = 1470 N
Now, let's calculate the work done to raise the refrigerator.
W = F × d × cosθ
W = 1470 N × 8.0 m × cos(0°)
W = 11760 J
The work done to raise the refrigerator is 11760 J.
3. W = F × d × cosθ
First, let's calculate the force needed to lift the box.
F = m × g
F = 180.0 kg × 9.8 m/s²
F = 1764 N
Now, let's calculate the work done to lift the box.
W = F × d × cosθ
W = 1764 N × 32.0 m × cos(0°)
W = 565248 J
The work done to lift the box is 565248 J.
Learn more about work done at: https://brainly.com/question/28356414
#SPJ11
Question \| 1: What is weather? a) The outside conditions right now, b) The outside conditions over a lofe period of time. c) A tool to measure the outside weather conditions.
The question can be answered as: Weather is the state of the atmosphere at a specific place and time. It refers to the current conditions such as temperature, humidity, wind, precipitation, and air pressure
Weather refers to the condition of the atmosphere at a given place and time, especially as it relates to temperature, precipitation, and other features like cloudiness, humidity, wind, and air pressure. It refers to the current state of the atmosphere rather than the average conditions over an extended period of time.Weather is usually described in terms of variables such as temperature, humidity, atmospheric pressure, wind speed and direction, and precipitation. Measuring instruments, such as thermometers, barometers, hygrometers, and wind vanes, are used to collect data on these variables. They help in predicting, reporting, and analyzing weather patterns.
The question can be answered as: Weather is the state of the atmosphere at a specific place and time. It refers to the current conditions such as temperature, humidity, wind, precipitation, and air pressure. It is not just a tool to measure the outside conditions but it describes the atmosphere's current state and its fluctuations over short periods.
Learn more about Weather :
https://brainly.com/question/32601421
#SPJ11
A boy sitting in a tree launches a rock with a mass 75 g straight up using a slingshot. The initial speed of the rock is 8.0 m/s and the boy, is 4.0 meters above the ground. The rock rises to a maximum height, and then falls to the ground. USE ENERGY CONSERVATIONTO SOLVE ALL OF THIS PROBLEM (20pts) a) Model the slingshot as acting. like a spring. If, during the launch, the boy pulls the slingshot back 0.8 m from its unstressed position, what must the spring constant of the slingshot be to achieve the 8.0 m/s launch speed? b) How high does the rock rise above the ground at its highest point? c) How fast is the rock moving when it reaches the ground? (assuming no air friction) If, due to air friction, the rock falls from the height calculated in Part b and actually strikes the ground with a velocity of 10 m/s, what is the magnitude of the (nonconservative) force due to air friction?
a) spring constant is approximately 3.7 N/m. b) height is approximately 1.1 m. c) The magnitude of the (nonconservative) force due to air friction when the rock hits the ground is approximately 0.32 N.
a)Model the slingshot as acting like a spring. If during the launch, the boy pulls the slingshot back 0.8 m from its unstressed position, the spring constant of the slingshot required to achieve the 8.0 m/s launch speed can be calculated as follows:Given: mass of the rock = 75 g = 0.075 kgInitial velocity of the rock = 8.0 m/s
Distance the boy pulls back the slingshot = 0.8 mThe net force acting on the rock as it moves from the unstressed position to its maximum displacement can be determined using Hooke's law:F = -kxHere,x = 0.8 mis the displacement of the spring from the unstressed position, andF = ma, wherea = acceleration = Δv/Δt
We know that the time for which the rock stays in contact with the slingshot is the time it takes for the spring to go from maximum compression to maximum extension, so it can be written as:Δt = 2t
Since the final velocity of the rock is 0, the displacement of the rock from maximum compression to maximum extension equals the maximum height the rock reaches above the ground. Using the principle of energy conservation, we can calculate this maximum height.
b)The maximum height the rock reaches above the ground can be calculated as follows:At the highest point, the velocity of the rock is 0, so we can use the principle of conservation of energy to calculate the maximum height of the rock above the ground.
c)The final velocity of the rock when it hits the ground can be calculated using the equation:[tex]vf^2 = vi^2 + 2ad[/tex]
wherevf = final velocity of the rock = 10 m/svi = initial velocity of the rock = -4.91 m/sd = displacement of the rock = 6.13 m
a) The spring constant of the slingshot required to achieve the 8.0 m/s launch speed is approximately 3.7 N/m.
b) The maximum height the rock reaches above the ground is approximately 1.1 m.
c) The magnitude of the (nonconservative) force due to air friction when the rock hits the ground is approximately 0.32 N.
Learn more about friction here:
https://brainly.com/question/28356847
#SPJ11
A 204 Ω resistor, a 0.825 H inductor, and a 7.00 μF capacitor are connected in series across a voltage source that has voltage amplitude 29.0 V and an angular frequency of 260 rad/s. Part A What is v at t = 22.0 ms? Express your answer with the appropriate units.
v = _____
Part B What is vR at t = 22.0 ms? Express your answer with the appropriate units. vR = ______ value _________ units
Part C What is vL at t = 22.0 ms?
Express your answer with the appropriate units.
The voltage at t = 22.0 ms is -12.39 V. The voltage across the resistor at t = 22.0 ms is -8.15 V. The voltage across the inductor at t = 22.0 ms is -11.31 V.
Resistor: R = 204 Ω
Inductor: L = 0.825 H
Capacitor: C = 7.00 μF
Voltage source: Vm = 29.0 V
Angular frequency: ω = 260 rad/s
Part A: The equation of the total voltage in a series RLC circuit is:
v(t) = Vm cos (ωt - Φ), where cos(ωt - Φ) is the voltage phasor.The voltage phasor is given by:Z = R + j (XL - XC)where XL = ωL is the inductive reactance, and XC = 1/ωC is the capacitive reactance. Here j = √(-1)
The phase angle of the circuit is given by:
tanΦ = (XL - XC) / RThe total voltage is:v(t) = Vm cos (ωt - Φ)
The current in the circuit is:
i(t) = (Vm / Z) cos (ωt - Φ)
Therefore, the voltage across the inductor is:
vL(t) = i(t) XL = (Vm / Z) XL cos (ωt - Φ)
Therefore, at t = 22.0 ms, the total voltage:
v(22 ms) = 29.0 cos (260 × 0.022 - 0.232) = - 12.39 V
Therefore, v = - 12.39 V
Part B: The voltage across the resistor is given by:
vR(t) = i(t) R
Therefore, at t = 22.0 ms, the voltage across the resistor:
vR(22 ms) = i(22 ms) R = (Vm / Z) R cos (ωt - Φ)vR(22 ms) = (29.0 / 388.93) 204 cos (260 × 0.022 - 0.232) = - 8.15 V
Therefore, vR = - 8.15 V
Part C: The voltage across the inductor is given by: vL(t) = i(t) XL
At t = 22.0 ms, the voltage across the inductor can be calculated as follows:
vL(22 ms) = i(22 ms) XL = (Vm / Z) XL cos (ωt - Φ)
vL(22 ms) = (29.0 / 388.93) (260 × 0.825) cos (260 × 0.022 - 0.232) = - 11.31 V
Therefore, the correct answer for Part C is vL = -11.31 V.
Learn more about voltage at: https://brainly.com/question/14883923
#SPJ11