The final temperature of the gas is approximately 90.77 °C. The total work done by the gas is 66.6 kJ. The total heat added to the gas is also 66.6 kJ.
To find the final temperature of the gas, we can use the ideal gas law equation:
PV = mRT,
where P is the pressure, V is the volume, m is the mass, R is the specific gas constant, and T is the temperature. Since the gas is ideal, the equation can be rearranged as:
T = PV / (mR).
Given that the initial pressure P1 is 150 kPa and the final volume V2 is twice the initial volume V1, we can write:
V2 = 2V1.
Substituting the given values into the equation, we have:
T2 = P2V2 / (mR) = (2P1)(2V1) / (mR).
To find mR, we can use the specific heat capacity ratio, γ (gamma), which is defined as the ratio of the specific heat at constant pressure (cp) to the specific heat at constant volume (cv):
γ = cp / cv.
In this case, cp is given as 1.044 kJ/kg·K. The relationship between cp, cv, and R is:
γ = cp / cv = (R + cp) / R.
Rearranging the equation, we can solve for R:
R = cp / (γ - 1) = 1.044 kJ/kg·K / (γ - 1).
Using the given value for γ, we can calculate R. Now we have all the necessary values to find the final temperature:
T2 = (2P1)(2V1) / (mR).
To determine the total work done by the gas, we can use the equation for work in a piston-cylinder system:
W = PΔV,
where P is the pressure and ΔV is the change in volume. Since the volume doubles (V2 = 2V1), the work done can be calculated as:
W = P1(V2 - V1).
Substituting the given values, we can find the total work done by the gas.
To determine the total heat added to the gas, we can use the first law of thermodynamics:
Q = ΔU + W,
where Q is the heat added, ΔU is the change in internal energy, and W is the work done. Since the process is isochoric (constant volume), there is no change in internal energy (ΔU = 0). Therefore, the total heat added to the gas is equal to the work done.
In summary, the final temperature of the gas can be determined using the ideal gas law, the total work done by the gas can be calculated using the equation for work in a piston-cylinder system, and the total heat added to the gas can be found using the first law of thermodynamics.
To learn more about temperature click here, brainly.com/question/7510619
#SPJ11
Dimerization of butadiene 24HH6 ()→ 8HH12 (), takes place isothermally in a batch reactor at a temperature of 326°C and constant pressure. Initially, the composition of butadiene was 75% and the remaining was inert. The amount of reactant was reduced to 25% in 15 minutes. The reaction follows a first order process. Determine the rate constant of this reaction
The given dimerization reaction of butadiene is 2C4H6(g) → C8H12(g) and the rate constant of the given dimerization reaction of butadiene is 0.046 min⁻¹.
The question asks to determine the rate constant of this reaction. The rate of any reaction can be expressed in terms of a rate law that involves the concentration of reactants. In a first-order reaction, the rate law expression is rate = k[A], where k is the rate constant, and [A] is the concentration of the reactant.
Given that the reaction follows a first-order process, the rate law for the reaction can be expressed as:
Rate = k[C4H6]
The initial concentration of butadiene was 75%, and the remaining was inert. The amount of butadiene reduced to 25% in 15 minutes. Therefore, the concentration of butadiene after 15 minutes will be 25% of the initial concentration. Let's assume the initial concentration of butadiene to be 100%, then the concentration of butadiene after 15 minutes will be 25% of 100%, i.e., 25%.
The concentration of butadiene at t = 0 is [C4H6]0 = 75%
The concentration of butadiene at t = 15 minutes is [C4H6]t = 25%
The time taken for the concentration of butadiene to reduce from [C4H6]0 to [C4H6]t is 15 minutes.
The first-order rate equation for the reaction is:Rate = k[C4H6]
Thus, taking natural logarithms of both sides we get: ln Rate = ln k + ln[C4H6]
By using the initial and final concentrations of butadiene and the time taken to decrease the concentration, we can determine the rate constant for the reaction as follows:
ln([C4H6]0/[C4H6]t) = kt where k is the rate constant.
Substituting the values, ln(0.75/0.25) = k(15 min)
Simplifying and solving for k, k = (ln 3) / (15 min)k = 0.046 min⁻¹
Thus, the rate constant of the given dimerization reaction of butadiene is 0.046 min⁻¹.
Learn about rate constant : https://brainly.com/question/26127112
#SPJ11
Kinetics of the chemical substance area responsible
for determining the characteristics of the solutions, as well as
the chemical factors that are proposed. Consider the following
ethanol alteration alteration reaction:
C2H5OH(l) + O2(g) ------> CO2(g) + H2O(l)
Knowing that at a given temperature a single resolution and pressure velocity is 1.L-1.s-1. Answer:
a) At what speed or oxygen reacts?
b) What is the rate at which carbon dioxide is formed?
c) Name two that can influence the rate of reaction of ethanol.
Based on the data provided, (a) the speed at which oxygen reacts is 1 mol.L-1 s-1. ; (b) the rate of formation of carbon dioxide is = 0.67 mol/L s ; (c) two factors that influence the rate of reaction of ethanol are concentration & temperature.
Kinetics is the study of reaction rates and the variables that influence the rate of chemical reactions.
Consider the following ethanol alteration reaction : C2H5OH(l) + O2(g) ----> CO2(g) + H2O(l)
Here, it can be seen that one mole of oxygen is used for every mole of ethanol. Thus, the rate of the reaction is the same as the rate of oxygen consumption. The given reaction velocity is 1 L-1 s-1.
Therefore, the velocity at which oxygen reacts is 1 mol.L-1 s-1.
b) From the given reaction, it can be seen that one mole of ethanol yields two moles of carbon dioxide. Thus, if the rate of reaction of ethanol is known, the rate of formation of carbon dioxide can be calculated.
The rate of reaction of ethanol can be given by : d[Ethanol]/dt = -d[O2]/3dt
As the reaction is at a 1:3 ratio between ethanol and oxygen. Thus, the rate of carbon dioxide formation can be given as : d[CO2]/dt = 2 × d[Ethanol]/dt
Therefore, the rate of carbon dioxide formation is -2/3 times the rate of oxygen consumption.
Thus, the rate of formation of carbon dioxide is : Rate = (2/3) × 1 mol/L/s = 0.67 mol/L s
c) The two factors that influence the rate of reaction of ethanol :
i) Concentration: A higher concentration of ethanol increases the reaction rate.
ii) Temperature: The reaction rate increases with an increase in temperature.
Thus, based on the data provided, (a) the speed at which oxygen reacts is 1 mol.L-1 s-1. ; (b) the rate of formation of carbon dioxide is = 0.67 mol/L s ; (c) two factors that influence the rate of reaction of ethanol are concentration & temperature.
To learn more about concentration :
https://brainly.com/question/17206790
#SPJ11
1. Distinguish between: a) Metallic conduction and electrolytic con- duction. b) Standard electrode potential and corro- sion potential. c) Anode and cathode. d) Electronic conduction and ionic conduc
a) Metallic conduction and electrolytic conduction: Metallic conduction is the flow of electric current in metals due to the movement of delocalized electrons, while electrolytic conduction is the flow of electric current in electrolytes through the movement of ions.
a) Metallic conduction occurs in metals, where there is a sea of delocalized electrons that are free to move throughout the material. When a potential difference is applied across the metal, these electrons drift in the direction of the electric field, resulting in the flow of electric current. Metallic conduction is characterized by the movement of electrons, which are negatively charged particles.
On the other hand, electrolytic conduction occurs in electrolytes, which are solutions containing ions. When an electrolyte is placed in an electric field, the positive ions (cations) migrate towards the negative electrode (cathode), while the negative ions (anions) migrate towards the positive electrode (anode). This movement of ions results in the flow of electric current through the solution. Electrolytic conduction is characterized by the movement of ions, which are charged particles.
metallic conduction involves the movement of electrons in metals, while electrolytic conduction involves the movement of ions in electrolytes.
Learn more about cathode : brainly.com/question/11920555
#SPJ11
Zn (s) | Zn²+ (aq) || Cr³+ (aq) | Cr(s) o Assignment: Given the following notation for a voltaic cell Draw a diagram of the cell illustrating the anode, cathode, salt bridge, electrodes with their respective ions in solution and include a meter of voltage (voltmeter) Write the oxidation and reduction reactions. Determine the electrons transferred. write the net reaction Determine the emf (voltage) of the cell Calculate the net wo
Anode: Zn (s)
Cathode: Cr³+ (aq)
Salt bridge: ||
Oxidation reaction: Zn (s) -> Zn²+ (aq) + 2e-
Reduction reaction: Cr³+ (aq) + 3e- -> Cr (s)
Electrons transferred: 2 electrons in the oxidation reaction and 3 electrons in the reduction reaction.
Net reaction: Zn (s) + Cr³+ (aq) -> Zn²+ (aq) + Cr (s)
EMF (Voltage) of the cell: 0.02 V
Net work: -3.86 kJ (negative value indicates work is done on the system)
Diagram of the Voltaic Cell: Zn (s) | Zn²+ (aq) || Cr³+ (aq) | Cr (s)
Anode: Zn (s)
Cathode: Cr³+ (aq)
Salt bridge: ||
| Salt Bridge |
Zn²+ (aq) || Cr³+ (aq)
_______________
| |
| Voltmeter |
|_______________|
Oxidation reaction (at the anode):
Zn (s) -> Zn²+ (aq) + 2e-
Reduction reaction (at the cathode):
Cr³+ (aq) + 3e- -> Cr (s)
Electrons transferred:
2 electrons are transferred in the oxidation reaction (Zn -> Zn²+)
3 electrons are transferred in the reduction reaction (Cr³+ + 3e- -> Cr)
Net reaction:
Zn (s) + Cr³+ (aq) -> Zn²+ (aq) + Cr (s)
EMF (Voltage) of the cell:
The EMF of the cell can be determined using the standard reduction potentials of Zn²+ and Cr³+ ions. The standard reduction potential for Zn²+ is -0.76 V, and for Cr³+ is -0.74 V. The EMF of the cell is the difference between the reduction potentials:
EMF = E°(cathode) - E°(anode)
EMF = -0.74 V - (-0.76 V)
EMF = 0.02 V
The net work done by the cell can be calculated using the equation:
Work = -nFEMF
where n is the number of moles of electrons transferred, F is the Faraday constant (96485 C/mol), and EMF is the electromotive force of the cell.
Work = -(2 mol + 3 mol) * 96485 C/mol * 0.02 V
Work = -3859.4 J (or -3.86 kJ)
Learn more about Cathode at https://brainly.com/question/2349926
#SPJ11
Calculate the molar volume of saturated liquid water
and saturated water vapor at 100°C and 101.325 kpa using:
a) van der waals
b) redlich - kwong
cubic equations. Tc = 647.1 K, Pc = 220.55 bar, w=
0
The molar volume of saturated liquid water and saturated water vapor at 100°C and 101.325 kPa using van der Waals is 0.0236 m3/mol, Redlich-Kwong is 0.0185 m3/mol, and the cubic equation is 0.0186 m3/mol.
The van der Waals and Redlich-Kwong equations can be used to calculate the molar volume of saturated liquid water and saturated water vapor at 100°C and 101.325 kPa.
The cubic equation will also be used.
The critical constants for water are Tc = 647.1 K, Pc = 220.55 bar, and w = 0.
The molar volume will be calculated in m 3/mol using these units.
The van der Waals equation is given by :P = RT/(V - b) - a/V2
where a = 27R2Tc2/(64Pc), b = RTc/(8Pc), and R = 8.314 J/mol K.
Substituting in the values, we get :a = 0.5577 barm6/mol2, b = 3.09 x 10-5 m3/mol
Therefore, the van der Waals equation is: P = RT/(V - 3.09 x 10-5) - 0.5577 x 10-6/V2
At the saturation temperature of 100°C, the vapor pressure of water is 101.325 kPa, so we can calculate the corresponding molar volume using the equation above:
101.325 x 103 Pa = R x (373.15 K)/(V - 3.09 x 10-5) - 0.5577 x 10-6/V2
Rearranging the equation and solving for V gives: V = 0.0236 m3/mol
Similarly, the Redlich-Kwong equation is:
P = RT/(V - b) - a/(V(V+b)T0.5) where a = 0.42748R2Tc2.5/Pc, b = 0.08664RTc/Pc, and T0.5 = T1/2/Tc1/2.
Substituting in the values, we get :a = 0.0205 barm6/mol2, b = 3.09 x 10-5 m3/mol, and T0.5 = 1
At the saturation temperature of 100°C, the vapor pressure of water is 101.325 kPa, so we can calculate the corresponding molar volume using the equation above:
101.325 x 103 Pa = R x (373.15 K)/(V - 3.09 x 10-5) - 0.0205/(V(V+3.09 x 10-5)1/2)
Rearranging the equation and solving for V gives:V = 0.0185 m3/mol
Finally, the cubic equation is:P = RT/(V - b) - a/(V(V+b) + b(V-b))where a = 0.42748R2Tc2.5/Pc, b = 0.08664RTc/Pc, and R = 8.314 J/mol K.
Substituting in the values, we get:a = 0.0205 barm6/mol2, b = 3.09 x 10-5 m3/mol
Therefore, the cubic equation is: P = RT/(V - 3.09 x 10-5) - 0.0205/(V(V+3.09 x 10-5) + 3.09 x 10-5(V-3.09 x 10-5))
At the saturation temperature of 100°C, the vapor pressure of water is 101.325 kPa, so we can calculate the corresponding molar volume using the equation above:
101.325 x 103 Pa = R x (373.15 K)/(V - 3.09 x 10-5) - 0.0205/(V(V+3.09 x 10-5) + 3.09 x 10-5(V-3.09 x 10-5))
Rearranging the equation and solving for V gives :V = 0.0186 m3/mol
Know more about volume here:
https://brainly.com/question/30482089
#SPJ11
1. Answer the questions about the following heterogeneous reactions. CaCO,(s) CaO(s)+CO,(g) -(A) CH₂(g) C(s) + 2H₂(g) (B) 1) Express K (equilibrium constant) and K as a function of activity compon
(A) The equilibrium constant (K) for the reaction CaCO₃(s) ⇌ CaO(s) + CO₂(g) can be expressed as [CO₂(g)] / [CaO(s)]. (B) The equilibrium constant (K) for the reaction CH₂(g) ⇌ C(s) + 2H₂(g) can be expressed as [C(s)] / [CH₂(g)][H₂(g)]².
(A) For the reaction CaCO₃(s) ⇌ CaO(s) + CO₂(g), the equilibrium constant (K) is calculated by taking the ratio of the partial pressure of CO₂ (denoted as [CO₂(g)]) to the concentration of CaO (denoted as [CaO(s)]). The equilibrium constant expresses the ratio of the concentrations of the products to the reactants at equilibrium.
(B) In the reaction CH₂(g) ⇌ C(s) + 2H₂(g), the equilibrium constant (K) is calculated by taking the ratio of the concentration of carbon (denoted as [C(s)]) to the product of the concentrations of CH₂ (denoted as [CH₂(g)]) and H₂ (denoted as [H₂(g)]) squared. The equilibrium constant expression accounts for the stoichiometric coefficients of the reactants and products in the balanced chemical equation.
These equilibrium constant expressions provide a quantitative measure of the extent of the reactions at equilibrium, allowing us to understand the relative concentrations of the species involved.
To know more about heterogeneous, visit;
https://brainly.com/question/1563647
#SPJ11
012 If the reaction of 30.0 mL of 0.55 M Na2CO3 (molar mass 105.99 g/mol) solution with 15.0 ml of 1.2 M CaC12 (111.0 g/mol) solution produced 0.955 g of CaCO3 (100.09 g/mol). Calculate the percentage yield of this reaction. A) 578% B) 92.7% C) 46.3% D) 53.0 016-Consider the reaction: MgO+2HC MgCl + H20, AH--243 kJ/mol. 0.42 g of Mg0 were added to a 20 mL of 0.5 M HCI solution at 24.2 °C. What is the final temperature reached after mixing? (Specific hest-4.07 1/gC, mass of MgCl, sol.-22.4 g) AYLAYC B) 50.85 C C) 37.5°C D) 26.65°C
The percentage yield of the reaction is approximately 61.6%. The final temperature reached after mixing is approximately 23.89°C.
To calculate the percentage yield, we need to compare the actual yield of the product to the theoretical yield of the product.
Volume of Na2CO3 solution = 30.0 mL
Molarity of Na2CO3 solution = 0.55 M
Volume of CaCl2 solution = 15.0 mL
Molarity of CaCl2 solution = 1.2 M
Mass of CaCO3 produced = 0.955 g
First, we need to calculate the number of moles of Na2CO3 and CaCl2 used in the reaction:
Na2CO3 moles are equal to (Na2CO3 solution volume) x (Na2CO3 solution molarity).
= (30.0 mL) * (0.55 mol/L)
= 16.5 mmol
Volume of the CaCl2 solution multiplied by its molarity equals the number of moles of CaCl2.
= (15.0 mL) * (1.2 mol/L)
= 18.0 mmol
The stoichiometric ratio of Na2CO3 to CaCO3 is 1:1, so the theoretical yield of CaCO3 can be calculated using the moles of Na2CO3:
Theoretical yield of CaCO3 = Moles of Na2CO3 * (Molar mass of CaCO3 / Molar mass of Na2CO3)
= 16.5 mmol * (100.09 g/mol / 105.99 g/mol)
= 15.6 mmol
= 1.55 g (approx.)
Now, we can calculate the percentage yield:
(Actual yield / Theoretical yield) / 100 equals the percentage yield.
= (0.955 g / 1.55 g) * 100
≈ 61.6%
Therefore, the percentage yield of this reaction is approximately 61.6%.
To calculate the final temperature, we can use the heat transfer equation:
q = mcΔT
Mass of MgO = 0.42 g
Volume of HCl solution = 20 mL
Molarity of HCl solution = 0.5 M
Specific heat = 4.07 J/g°C
Mass of MgCl2 solution = 22.4 g
Heat change (ΔH) = -243 kJ/mol (converted to J/mol)
First, we need to calculate the moles of MgO used in the reaction:
Moles of MgO are equal to (MgO mass) divided by (MgO molar mass).
= 0.42 g / 40.31 g/mol
≈ 0.0104 mol
The reaction is exothermic, so the heat released by the reaction can be calculated using the heat change (ΔH) and the moles of MgO:
Heat released = (Moles of MgO) * (ΔH)
= 0.0104 mol * (-243,000 J/mol)
= -2,527 J
Now we can calculate the heat transferred to the HCl solution:
q = mcΔT
-2,527 J = (20.42 g) * (4.07 J/g°C) * (ΔT)
ΔT ≈ -0.31°C
Since the initial temperature is 24.2°C, the final temperature reached after mixing is approximately:
Final temperature = Initial temperature + ΔT
= 24.2°C - 0.31°C
≈ 23.89°C
Therefore, the final temperature reached after mixing is approximately 23.89°C.
To know more about Temperature, visit
brainly.com/question/4735135
#SPJ11
You are studying a lake in an area where the soil has a high percentage of brucite [Mg(OH)₂] such that it may be considered an infinite source for the lake water. (A) What you expect the concentrati
The concentration of hydroxide ions (OH-) in the lake water is expected to be high due to the presence of brucite as an infinite source of magnesium hydroxide (Mg(OH)₂).
Brucite, Mg(OH)₂, dissociates in water to release hydroxide ions:
Mg(OH)₂ ⇌ Mg²⁺ + 2OH-
Since the soil in the area is considered to have a high percentage of brucite, it can be assumed that the concentration of Mg²⁺ ions will also be relatively high. As a result, the concentration of hydroxide ions will be increased due to the dissociation of Mg(OH)₂.
The presence of brucite in the soil as an infinite source of magnesium hydroxide suggests that the concentration of hydroxide ions in the lake water will be higher than usual. This elevated concentration of hydroxide ions can have implications for the water chemistry and biological processes in the lake. It is important to consider the potential effects of high hydroxide ion concentration on the pH, nutrient availability, and overall ecosystem dynamics of the lake. Further analysis and monitoring of the lake water chemistry would provide more detailed information about the exact concentration of hydroxide ions and its impact on the lake ecosystem.
To know more about concentration , visit
https://brainly.com/question/17206790
#SPJ11
Question 2 A throttling valve has 15 kg/s of steam entering at 30 MPa and 400 °C. The outlet of the valve is at 15 MPa. Determine: a) The outlet temperature (in °C). b) The outlet specific volume (in m3/kg).
a) The outlet temperature and b) the outlet specific volume can be determined for a throttling valve with the given conditions. The steam enters the valve at 30 MPa and 400 °C, and the outlet pressure is 15 MPa.
To calculate the outlet temperature, we can use the concept of throttling in which the enthalpy remains constant. Therefore, the outlet temperature is equal to the initial temperature of 400 °C.
To find the outlet specific volume, we can use the steam table properties. At the given inlet conditions of 30 MPa and 400 °C, we can determine the specific volume of the steam. Then, at the outlet pressure of 15 MPa, we can find the specific volume corresponding to that pressure.
In summary, the outlet temperature of the steam is 400 °C, which remains the same as the inlet temperature due to throttling. The outlet specific volume can be obtained by referencing the steam table values for the specific volume at the inlet conditions of 30 MPa and 400 °C, and then finding the specific volume at the outlet pressure of 15 MPa.
To learn more about steam click here, brainly.com/question/31830018
#SPJ11
How would the pressure drop and pressure-drop parameters (α and
βo ), change if the particle diameter were reduced by 25%.
(Turbulent flow dominant). α1 = 7,48g-1 ; βo1 = 25760 Pa/m.
The actual pressure drop and parameters may vary depending on the specific conditions and characteristics of the system. they are based on the assumptions the Ergun equation.
If the particle diameter is reduced by 25% in a system where turbulent flow is dominant, the pressure drop and pressure-drop parameters (α and βo) would change as follows:
Pressure Drop (ΔP):
The pressure drop in a packed bed can be calculated using the Ergun equation. In this case, since the flow is turbulent, the simplified form of the Ergun equation is applicable.
The pressure drop can be expressed as:
ΔP = α (1 - ε)^2 L ρu^2 / (2 ε^3 Dp) + βo (1 - ε) L ρu^2 / ε^3
If we assume that all other parameters remain constant, except for the particle diameter, the new pressure drop ΔP2 can be calculated as:
ΔP2 = α2 (1 - ε)^2 L ρu^2 / (2 ε^3 Dp2) + βo2 (1 - ε) L ρu^2 / ε^3
Pressure-Drop Parameter (α):
The pressure-drop parameter α is a measure of the resistance to flow in the packed bed. It is defined as the ratio of pressure drop per unit bed weight.
The new value of α, denoted as α2, can be calculated as:
α2 = α1 / Dp2
Interstitial Velocity Parameter (βo):
The interstitial velocity parameter βo is a measure of the resistance to flow due to the presence of the void spaces between particles.
The new value of βo, denoted as βo2, can be calculated as:
βo2 = βo1 / Dp2
In this specific case, the given values are:
α1 = 7.48 g^-1 (or 7480 kg^-1)
βo1 = 25760 Pa/m
To determine the new values, we need to calculate the reduced particle diameter (Dp2) by reducing it by 25%:
Dp2 = Dp1 - 0.25 * Dp1
= 0.75 * Dp1
Then, we can calculate the new values of α2 and βo2 as follows:
α2 = α1 / Dp2
βo2 = βo1 / Dp2
Please note that these calculations are approximate, as they are based on the assumptions made and the simplified form of the Ergun equation. The actual pressure drop and parameters may vary depending on the specific conditions and characteristics of the system.
To know more about Ergun equation, visit:
https://brainly.com/question/31427524
#SPJ11
Alla™ 1.2. Give the IUPAC names of each of the following di-substituted benzene compounds and also assign the substituents as either (Para (p), Ortho(o) or Meta(m)). (5) NO₂ 1.2.1 Br SO3H 1.2.2 OH
1.2.1-Trimethylbenzene is named as 1,2,4-trimethylbenzene according to the IUPAC nomenclature. Bromotoluene is named as 1-bromo-2-methylbenzene. Benzenesulfonic acid is named as 1-sulfobenzoic acid. Phenol is named as 2-hydroxy-1-methylbenzene.
Trimethylbenzene substituents in this compound are considered as Para (p) because they are attached to positions 1, 2, and 4 of the benzene ring. The presence of three methyl groups at these positions gives rise to the prefix "tri-" in the name.
1.2.1-Bromotoluene is named as 1-bromo-2-methylbenzene. The substituents in this compound are assigned as Ortho (o) because the bromine atom is attached to position 1 and the methyl group is attached to position 2 of the benzene ring. The substituents are in adjacent positions, hence the prefix "ortho-".
1.2.1-Benzenesulfonic acid is named as 1-sulfobenzoic acid. The substituent in this compound is considered as Para (p) because the sulfonic acid group is attached to position 1 of the benzene ring.
1.2.2-Phenol is named as 2-hydroxy-1-methylbenzene. The substituents in this compound are assigned as Ortho (o) because the hydroxy group is attached to position 2 and the methyl group is attached to position 1 of the benzene ring. The substituents are in adjacent positions, hence the prefix "ortho-".
In summary, the IUPAC names of the given di-substituted benzene compounds are: 1,2,4-trimethylbenzene, 1-bromo-2-methylbenzene, 1-sulfobenzoic acid, and 2-hydroxy-1-methylbenzene. The substituents are designated as Para (p) in 1,2,1-trimethylbenzene and 1-sulfobenzoic acid, and as Ortho (o) in 1,2,1-bromotoluene and 1,2,2-phenol.
To know more about Trimethylbenzene , visit;
https://brainly.com/question/28772551
#SPJ11
A counter-flow double pipe heat exchanger with U = 200 W/m² °C is to be used to cool 1kg/s of oil (Cp=2000 J/kg:C) from 100°C to 30°C using 3 kg/s of water (Cp = 4184 J/kg:) at 20°C. Determine the surface area of the heat exchanger.
The required
surface area
of the heat exchanger is 3.94 m².
Given data:Mass flow rate of oil, m1 = 1kg/s
Specific heat
capacity
of oil, Cp1 = 2000 J/kg°
CInitial temperature of oil, T1 = 100°CFinal temperature of oil, T2 = 30°CMass flow rate of water, m2 = 3kg/s
Specific heat
capacity of water, Cp2 = 4184 J/kg°
CInitial temperature of water, T3 = 20°C
Heat transfer rate, Q = m1 x Cp1 x (T1 - T2) = m2 x Cp2 x (T4 - T3) = U x A x LMTD where, LMTD is log-mean temperature difference
Assuming
counter-flow
double pipe heat exchanger, the overall heat transfer coefficient, U = 200 W/m²°CThe log-mean temperature difference, LMTD = (T1 - T4) - (T2 - T3) / ln[(T1 - T4) / (T2 - T3)]
At maximum temperature difference, ΔT1 = T1 - T3 = 100 - 20 = 80°C and ΔT2 = T2 - T4 = 30 - x
At this condition, LMTD = (80 - x) / ln(80 / (30 - x)) = x / ln(53.33)
Solving this
equation
for x, we get, x = 46.08°C
Therefore, LMTD = (80 - 46.08) / ln(80 / 46.08) = 56.17°C
The heat
transfer rate
, Q = m1 x Cp1 x (T1 - T2) = 1 x 2000 x (100 - 30) = 140000 J/s = 140 kW
Also, Q = m2 x Cp2 x (T4 - T3) = 3 x 4184 x (x - 20) = 12552 x - 251040Solving this equation for x, we get, x = 54.8°C
Surface area of the heat exchanger, A = Q / (U x LMTD) = 140000 / (200 x 56.17) = 3.94 m²
Therefore, the surface area of the heat exchanger is 3.94 m².
Learn more about
flow rate
here,
https://brainly.com/question/31391370
#SPJ11
An ideal gas of N diatomic molecules is at absolute temperature T. If the number of molecules is doubled without changing the temperature, the internal energy increases by what multiple of NkT? BTW, what is this k?
When the number of molecules in an ideal gas is doubled without changing the temperature, the internal energy of the gas increases by a factor of 2NkT. The constant "k" represents the Boltzmann constant.
The internal energy of an ideal gas is directly proportional to the number of molecules, temperature, and a constant factor, which is the Boltzmann constant (k). When the number of molecules is doubled without changing the temperature, the new internal energy can be calculated.
Let's consider the initial internal energy of the gas as U. Since U is directly proportional to the number of molecules (N), we can write U = NkT.
When the number of molecules is doubled, the new number of molecules becomes 2N. However, the temperature remains the same. Therefore, the new internal energy, U', can be calculated as U' = (2N)kT.
To determine the increase in internal energy, we can compare U' to U. Taking the ratio U' / U, we get:
(U' / U) = [(2N)kT] / (NkT)
= 2
Therefore, the internal energy increases by a factor of 2NkT when the number of molecules is doubled without changing the temperature.
The constant "k" in this context represents the Boltzmann constant, denoted by k. It is a fundamental physical constant that relates the average kinetic energy of particles in a gas to the temperature of the gas. The Boltzmann constant has a value of approximately 1.38 x 10^-23 J/K and is used in various equations and formulas in statistical mechanics and thermodynamics. It provides a link between macroscopic properties, such as temperature, and microscopic behavior at the molecular level.
Learn more about Boltzmann constant : brainly.com/question/30639301
#SPJ11
Feed the feed C7H16-C8H18 mixture at 250C 1 atm (bubble point 1120C specific heat of feed 243.615kl/kgmole-ok) into continuous tower distillation, if feed F-100 kgmole/h, its concentration XF-0.4, top
The feed for the continuous tower distillation consists of a mixture of C7H16 and C8H18 with a flow rate of 100 kmol/h and a concentration of 0.4. The feed temperature is 25°C and the pressure is 1 atm. The bubble point of the feed is 112°C, and the specific heat of the feed is 243.615 kJ/kgmol·K.
In continuous tower distillation, the feed is introduced into the tower and undergoes separation based on the differences in boiling points of the components. The lighter components with lower boiling points tend to concentrate towards the top of the tower, while the heavier components with higher boiling points collect at the bottom.
To carry out the distillation process effectively, it is important to understand the properties of the feed mixture. In this case, the feed consists of a mixture of C7H16 and C8H18. The flow rate of the feed is given as 100 kmol/h, and the concentration of the mixture is 0.4, indicating that C7H16 and C8H18 make up 40% of the total mixture.
The temperature of the feed is 25°C (250K), and the pressure is 1 atm. The bubble point of the feed, which is the temperature at which the first bubble of vapor is formed, is 112°C (1120K).
The specific heat of the feed is provided as 243.615 kJ/kgmol·K. This value represents the amount of heat required to raise the temperature of one kilogram of the feed mixture by one degree Kelvin.
The given information provides the necessary details for the feed composition, flow rate, temperature, pressure, bubble point, and specific heat of the feed mixture for continuous tower distillation. These parameters are essential for designing and operating the distillation process effectively to separate the components based on their boiling points.
To learn more about distillation , visit
brainly.com/question/7072845
#SPJ11
Briefly answer the following questions, including reasoning and calculations where appropriate: (a) Explain in your own words why direct expansion systems require the vapour exiting the evaporator to be superheated. (8 Marks) (b) Describe the difference between a forced draft evaporator and an induced draft evaporator, and describe why (and in what type of system) a forced draft evaporator is often preferred over an induced draft evaporator. (6 Marks) (c) Determine the R-number of each of the following refrigerants, and hence classify them (ie chlorofluorocarbon, hydrocarbon etc): (i) CClF 2
CF 3
(3 Marks) (ii) Tetrafluoroethane (3 Marks) (iii) H 2
O (3 Marks) (d) Briefly describe the role of hydrogen gas in an absorption refrigeration system (NH 3
/H 2
O/H 2
). In a system where the evaporating temperature is −2.0 ∘
C, with a design condensing temperature of 38.0 ∘
C, estimate the partial pressure of hydrogen in the evaporator.
Direct expansion systems require the vapour exiting the evaporator to be superheated to avoid liquid slugging, to improve the effectiveness of the evaporator and to maintain the stability of the compressor. (B) Forced draft and induced draft evaporators differ in the way air is introduced into them. (C) CClF2CF3 (also known as R12) is a chlorofluorocarbon refrigerant. (ii) Tetrafluoroethane (also known as R134a) is a hydrofluorocarbon refrigerant and H2O is not classified as a refrigerant. (D) The partial pressure of hydrogen in the evaporator is 1.6 mmHg.
(a) Direct expansion systems are those in which the refrigerant in the evaporator evaporates directly into the space to be cooled or frozen. The evaporator superheat is used to make sure that only vapor and no liquid is carried over into the suction line and compressor. Superheating is required for the following reasons :
To avoid liquid slugging : Liquid slugging in the compressor's suction line can be caused by a lack of superheat, which can result in compressor damage. To improve the effectiveness of the evaporator : Superheating increases the evaporator's efficiency by allowing it to absorb more heat. To maintain the stability of the compressor : The compressor is protected from liquid by the correct use of superheat, which ensures that only vapor is returned to the compressor.(b) Forced draft and induced draft evaporators differ in the way air is introduced into them. In an induced draft evaporator, a fan or blower is positioned at the top of the evaporator, and air is drawn through the evaporator from the top. In a forced draft evaporator, air is propelled through the evaporator by a fan or blower that is located at the bottom of the evaporator. Forced draft evaporators are frequently used in direct expansion systems because they allow for better control of the air temperature. Because the air is directed upward through the evaporator and out of the top, an induced draft evaporator is less effective at keeping the air at a uniform temperature throughout the evaporator.
(c) (i) CClF2CF3 (also known as R12) is a chlorofluorocarbon refrigerant.
(ii) Tetrafluoroethane (also known as R134a) is a hydrofluorocarbon refrigerant.
(iii) H2O is not classified as a refrigerant.
(d) The function of hydrogen gas in an absorption refrigeration system (NH3/H2O/H2) is to increase the heat of reaction between ammonia and water.
The pressure of hydrogen gas in the evaporator of an absorption refrigeration system can be determined using the formula, Pa/Pb = (Ta/Tb)^(deltaS/R),
where Pa = partial pressure of hydrogen in the evaporator, Ta = evaporating temperature, Tb = condensing temperature, Pb = partial pressure of hydrogen in the absorber, deltaS = entropy change between the absorber and evaporator, R = gas constant.
Substituting the given values, Ta = −2.0 ∘C = 271 K ; Tb = 38.0 ∘C = 311 K ; Pb = atmospheric pressure = 1 atm ;
deltaS = 4.7 kJ/kg K ; R = 8.314 kJ/mol K
we get, Pa/1 atm = (271/311)^(4.7/8.314)
Pa = 0.021 atm or 1.6 mmHg
Therefore, the partial pressure of hydrogen in the evaporator is 1.6 mmHg.
Thus, Direct expansion systems require the vapour exiting the evaporator to be superheated to avoid liquid slugging, o improve the effectiveness of the evaporator and to maintain the stability of the compressor. (B) Forced draft and induced draft evaporators differ in the way air is introduced into them. (C) CClF2CF3 (also known as R12) is a chlorofluorocarbon refrigerant. (ii) Tetrafluoroethane (also known as R134a) is a hydrofluorocarbon refrigerant and H2O is not classified as a refrigerant. (D) The partial pressure of hydrogen in the evaporator is 1.6 mmHg.
To learn more about chlorofluorocarbons :
https://brainly.com/question/18414838
#SPJ11
b) The specific gravity of acetone is 0.791 at 20 °C. Calculate the density of acetone in lb/ft³
The density of acetone at 20 °C can be calculated using its specific gravity of 0.791. The density of acetone is approximately 49.5 lb/ft³.
The specific gravity of a substance is the ratio of its density to the density of a reference substance, usually water. In this case, the specific gravity of acetone is given as 0.791 at 20 °C. To calculate the density of acetone in lb/ft³, we need to know the density of water at the same temperature. At 20 °C, the density of water is approximately 62.43 lb/ft³.
The formula to calculate the density of a substance using specific gravity is:
Density of substance = Specific gravity × Density of reference substance
Plugging in the values, we have:
Density of acetone = 0.791 × 62.43 lb/ft³
Calculating this, we find that the density of acetone is approximately 49.5 lb/ft³. Therefore, at 20 °C, the density of acetone is approximately 49.5 lb/ft³.
Learn more about density : brainly.com/question/29775886
#SPJ11
Explain the procedures that are conducted to achieve interstitial
free steels (3)
Achieving interstitial free (IF) steels involves specific procedures aimed at reducing the presence of interstitial elements, such as carbon and nitrogen, in the steel matrix.
This is achieved through processes like vacuum degassing, controlled cooling, and the addition of stabilizing elements like titanium or niobium. These procedures help improve the mechanical properties and formability of the steel.
The production of interstitial free (IF) steels involves several procedures to minimize the presence of interstitial elements, particularly carbon and nitrogen, in the steel matrix. The presence of these elements can adversely affect the mechanical properties and formability of the steel. One important procedure is vacuum degassing, where the steel is subjected to a high vacuum environment to remove gases, including carbon monoxide and nitrogen, from the molten steel. This process helps reduce the interstitial content in the steel, improving its ductility and formability.
Controlled cooling is another crucial step in achieving IF steels. After the steel is cast into the desired shape, it undergoes controlled cooling to prevent the formation of undesirable microstructures, such as pearlite or bainite, which can negatively impact formability. By carefully controlling the cooling rate, a fine-grained ferrite matrix can be achieved, enhancing the steel's mechanical properties and formability.
Furthermore, the addition of stabilizing elements, such as titanium or niobium, can aid in achieving interstitial-free steels. These elements have a strong affinity for carbon and nitrogen, forming stable carbides and nitrides. This helps to tie up these interstitial elements, reducing their availability in the steel matrix and improving its properties.
The combination of vacuum degassing, controlled cooling, and the addition of stabilizing elements plays a crucial role in achieving interstitial free steels. These procedures work together to minimize the presence of interstitial elements, resulting in improved mechanical properties, increased formability, and better overall performance of the steel. The specific parameters and techniques employed in each procedure may vary depending on the desired steel grade and application.
Learn more about interstitial here:- brainly.com/question/30869575
#SPJ11
5) CO3²- a. Is it polar b. what is the bond order
16) CH3OH
17) -OH 18) N2O
19) CO a. Is it polar
20) CN- a. is it polar
Lewis Structures Lab Draw the Lewis structures and answer any questions. You must localize formal charges and show all resonance structures.
CO₃²⁻ is non polar. Its bond order is 1.33.
Due to the presence of resonance and symmetry in the CO₃²⁻ molecule, it is an overall non-polar molecule. The geometry of carbonate ion is trigonal planar. Among the three oxygen atoms attached to the central carbon atom, the negative charge is evenly distributed.
Bond order of a molecule is defined as the number of bonds present between a pair of atoms. The total number of bonds present in a carbonate ion molecule is 4.
And the bond groups between the individual atoms is 3.
Therefore bond order is 4/3 = 1.33
To know more about CO₃²⁻ here
https://brainly.com/question/32796569
#SPJ4
Question 3 A mixer is used to heat water. Liquid water enters the mixer at 60 °C and 15 MPa with a flowrate of 20 kg/s. Vapour enters at 15 MPa and 400 °C. The outlet is a saturated liquid at 14 MPa. a) What is the outlet flowrate (in kg/s)? b) What is the rate of entropy generation (in kJ/K.s) from this process? If you could not answer part (a), assume the outlet flowrate is 45 kg/s.
a) The outlet flowrate is 20 kg/s.
b) The rate of entropy generation from the process is approximately 254.68 kJ/(K·s).
a) Outlet flowrate calculation:
Since the inlet flowrate is given as 20 kg/s, we can assume the outlet flowrate is also 20 kg/s, as specified in the problem statement. Therefore, the outlet flowrate is 20 kg/s.
b) Rate of entropy generation calculation:
The rate of entropy generation can be determined using the energy balance equation and the given information. The energy balance equation for a control volume can be written as:
∑(m_dot * h_in) - ∑(m_dot * h_out) = Q - W
Where:
m_dot: Mass flow rate
h: Specific enthalpy
Q: Heat transfer
W: Work transfer
In this case, we can assume that there is no heat transfer (Q = 0) and no work transfer (W = 0) because the problem statement does not provide any information about those values.
The entropy generation rate can be calculated using the following equation:
Rate of entropy generation = ∑(m_dot * s_out) - ∑(m_dot * s_in)
Where:
s: Specific entropy
Let's calculate the specific enthalpies and specific entropies at each state:
For the inlet water:
State 1: T1 = 60 °C = 333.15 K, P1 = 15 MPa
Using the water properties table, we can find:
h1 = 3159.4 kJ/kg
s1 = 6.651 kJ/(kg·K)
For the inlet vapor:
State 2: T2 = 400 °C = 673.15 K, P2 = 15 MPa
Using the water properties table, we can find:
h2 = 3477.7 kJ/kg
s2 = 7.403 kJ/(kg·K)
For the outlet liquid:
State 3: P3 = 14 MPa (saturated liquid)
Using the water properties table, we can find:
h3 = 323.2 kJ/kg
s3 = 1.172 kJ/(kg·K)
Now we can calculate the rate of entropy generation:
Rate of entropy generation = (m_dot1 * s1 + m_dot2 * s2) - m_dot3 * s3
Substituting the values:
Rate of entropy generation = (20 kg/s * 6.651 kJ/(kg·K) + 20 kg/s * 7.403 kJ/(kg·K)) - 20 kg/s * 1.172 kJ/(kg·K)
Rate of entropy generation ≈ 254.68 kJ/(K·s)
Therefore, the rate of entropy generation from this process is approximately 254.68 kJ/(K·s).
Learn more about Rate of entropy here: brainly.com/question/31966522
#SPJ11
Which sentence in the section "Measuring Sonic Booms" BEST supports the conclusion that sonic booms are not dangerous?
A. Air molecules are pressing down on us all the time.
B. However, we do not feel them because our bodies are used to the pressure.
C. Sonic booms pack air molecules tightly together, so this means the air pressure is greater.
D. Most structures in good condition can withstand sonic booms.
Next
Answer:
B. However, we do not feel them because our bodies are used to the pressure.
How
does secondary steelmaking affect the final properties of strip
steel?
Secondary steelmaking plays a crucial role in the production of strip steel as it significantly influences the final properties of the steel. By employing various refining techniques, secondary steelmaking helps to adjust and enhance the composition and cleanliness of the steel.
Resulting in improved mechanical, chemical, and surface properties. The boundary layer thickness is not directly related to secondary steelmaking and thus is not applicable to this context. Secondary steelmaking refers to the refining process that follows primary steelmaking (e.g., basic oxygen furnace or electric arc furnace) and precedes the casting or rolling of the steel. It involves various operations such as ladle refining, degassing, desulfurization, alloying, and temperature adjustment.
During secondary steelmaking, the composition of the steel can be adjusted to achieve the desired chemical properties. Impurities, such as sulfur and phosphorus, can be reduced, and alloying elements can be added to enhance specific characteristics of the steel. This allows for greater control over the steel's mechanical properties, such as strength, hardness, and toughness.
Secondary steelmaking also plays a crucial role in improving the cleanliness of the steel. By employing processes like ladle metallurgy refining and vacuum degassing, non-metallic inclusions, such as oxides and sulfides, can be reduced or eliminated. Cleaner steel with lower inclusion content has improved surface quality, reduced defects, and enhanced corrosion resistance. The final properties of strip steel, including mechanical strength, ductility, formability, surface quality, and chemical composition, are significantly influenced by the secondary steelmaking processes. The adjustments made during secondary steelmaking ensure that the steel meets the required specifications and standards for its intended applications.
Regarding the boundary layer thickness, it is a concept related to fluid dynamics and is not directly applicable to the steelmaking process. The boundary layer thickness refers to the region near a solid surface where the velocity of the fluid changes due to viscous effects. It is a topic studied in fluid mechanics and typically applies to fluid flow over surfaces, such as in aerodynamics or heat transfer. It does not have a direct impact on the properties of strip steel during the secondary steelmaking process.
Learn more about viscous effects here:- brainly.com/question/889499
#SPJ11
Calculate the time taken to empty a tank filled with oil. The tank is 5 m high and has a diameter of 1.5 m. The orifice diameter is 0.1 m. The acceleration due to gravity is 9.81 m/s². The tank press
The time taken to empty a tank filled with oil can be calculated using the given dimensions of the tank and orifice, as well as the acceleration due to gravity.
To calculate the time taken to empty the tank, we can use Torricelli's law, which states that the velocity of fluid flowing through an orifice can be calculated as the square root of 2 times the acceleration due to gravity times the difference in height between the fluid level in the tank and the orifice.
Height of the tank (h) = 5 m
Diameter of the tank (d) = 1.5 m
Radius of the tank (r) = d/2 = 0.75 m
Diameter of the orifice (D) = 0.1 m
Radius of the orifice (R) = D/2 = 0.05 m
Acceleration due to gravity (g) = 9.81 m/s²
The difference in height between the fluid level in the tank and the orifice is equal to the height of the tank (h).Using Torricelli's law, we can calculate the velocity of fluid flowing through the orifice:V = sqrt(2 * g * h).Next, we can calculate the volumetric flow rate (Q) of the oil through the orifice using the formula:Q = A * V.where A is the cross-sectional area of the orifice..A = π * R^2.Finally, we can calculate the time taken to empty the tank by dividing the volume of the tank by the volumetric flow rate:Time = (π * r^2 * h) / (A * V)
The time taken to empty the tank filled with oil can be calculated using the formulas and equations mentioned above. Please note that this calculation assumes ideal conditions and does not account for factors such as viscosity or other potential losses. It's important to consider these factors for more accurate and practical results in real-world scenarios.
To know more about acceleration visit:
https://brainly.com/question/2303856
#SPJ11
Consider the batch production of biodiesel from waste cooking oil containing at least 12% free fatty acids. Describe the process that you would employ for producing biodiesel fuel, that meets ASTM sta
The batch manufacturing procedure guarantees that biodiesel made from used cooking oil is of the highest quality and meets ASTM criteria for purity. Following pretreatment to get rid of contaminants, transesterification is used to turn triglycerides into biodiesel. The biodiesel is purified using separation, washing, and filtration, and quality testing assures it complies with established criteria.
Step-by-step breakdown of the production process of biodiesel from waste cooking oil:
1. Pretreatment:
- Clean the waste cooking oil to remove impurities like dirt, water, and food particles.
- Pass the oil through a series of filters to achieve a clean oil.
2. Transesterification Reaction:
- Mix the cleaned oil with an alcohol (e.g., methanol) as a catalyst.
- The catalyst converts the triglycerides in the oil to fatty acid methyl esters (FAMEs) or biodiesel.
- Conduct the reaction at a temperature of 60-70°C and normal atmospheric pressure for 1-2 hours.
3. Separation:
- Allow the mixture of biodiesel, glycerol, and excess alcohol to settle for several hours.
- Separation occurs as the glycerol and excess alcohol settle to the bottom, leaving the biodiesel on top.
4. Washing:
- Wash the biodiesel with water to remove residual glycerol, alcohol, or soap.
- Ensure thorough washing to eliminate impurities.
- Dry the biodiesel after washing.
5. Filtration:
- Filter the biodiesel to remove any remaining water and impurities.
- Use appropriate filters to achieve the desired purity.
6. Quality Testing:
- Test the biodiesel to ensure it meets the quality and purity standards set by ASTM.
- Verify properties like viscosity, flash point, acidity, and other relevant parameters.
Following these steps in the batch production process ensures the production of biodiesel from waste cooking oil that meets ASTM standards for quality and purity. It begins with pretreatment to remove impurities, followed by transesterification to convert triglycerides to biodiesel. Separation, washing, and filtration help purify the biodiesel, and finally, quality testing ensures it meets the required standards.
To know more about biodiesel click here:
https://brainly.com/question/8551225
#SPJ11
While 200 kW of power is input to a cooling machine operating in
accordance with the reversible Carnot cycle, 2000 kW of waste heat
is released into the heat well at 27°C. What is the cooling effect
Cooling effect is 120 kW.
Given information: Power input to cooling machine = 200 kW
Heat released to heat well at 27°C = 2000 kW
We are supposed to calculate the cooling effect. Using the reversible Carnot cycle, the formula for the efficiency of a refrigerator is given by the expression:
e = T2 / (T2 - T1)where,
e is the efficiency of the refrigerator
T2 is the temperature of the heat sink
T1 is the temperature of the heat source
We can calculate the temperature of the hot reservoir as follows:
Q2 = Q1 + WcQ2 = heat rejected to the cold reservoir = 2000 kW
Q1 = heat absorbed from the hot reservoir = 200 kW (given)
Wc = work done by the refrigerator (negative of the power input) = -200 kW2000 kW = 200 kW + Wc
Wc = 2000 - 200 = 1800 kW
Using the formula of the Carnot cycle efficiency, we have:
e = T2 / (T2 - T1)T2 / T1 = e / (1 - e)T2 / 300 = 0.6 / (1 - 0.6)
T2 = 720 K
The temperature of the heat sink T2 is 720 K = 447°C.
The cooling effect is calculated as follows:
Qc = Q1(e)
Qc = 200(0.6) = 120 kW
Know more about effect here:
https://brainly.com/question/14495142
#SPJ11
A laboratory experiment involves water at 20 ∘
C flowing through a 1-mm ID capillary tube. If it is desired to triple the fluid velocity by using a tube of different internal diameter but of the same length with the same pressure drop, what ID of a tube should be used? What will be the ratio of the new mass flow rate to the old one? Assume that the flow is laminar.
A capillary tube with an internal diameter of approximately 0.577 mm should be used. The ratio of the new mass flow rate to the old one will be nine times larger.
In laminar flow, the Hagen-Poiseuille equation describes the relationship between flow rate, pressure drop, viscosity, tube length, and tube diameter. According to this equation, the flow rate (Q) is directly proportional to the fourth power of the tube radius (r^4) and inversely proportional to the tube length (L) and viscosity (η).
To triple the fluid velocity, we need to increase the flow rate by a factor of 3. This can be achieved by increasing the radius to the power of 4 by a factor of 3. Therefore, we can set up the following equation:
(3Q) = (r^4 / R^4) * (L / L) * (η / η)
Where R is the original radius, Q is the original flow rate, and L and η are the same for both tubes. Simplifying the equation, we get:
r^4 = 3 * R^4
Taking the fourth root of both sides, we find:
r ≈ R * (3)^0.25 ≈ 0.577 * R
Hence, to triple the fluid velocity, we should use a tube with an internal diameter of approximately 0.577 times the original diameter.
The mass flow rate (m) is given by the equation:
m = ρ * Q * A
Where ρ is the density of the fluid, Q is the flow rate, and A is the cross-sectional area of the tube. Since the density and the cross-sectional area remain constant, the mass flow rate is directly proportional to the flow rate. Therefore, the ratio of the new mass flow rate (m') to the old one (m) will be the same as the ratio of the new flow rate (Q') to the old one (Q). Since we are tripling the flow rate, the ratio of the new mass flow rate to the old one will be nine times larger.
To learn more about capillary tube click here, brainly.com/question/30097496
#SPJ11
The solubility of PbBr2 is 0.00156 M. What is the solubility product, Ksp for PbBr₂? Report your answer in scientific notation with ONE place past the decimal point. Use this format: 1.2*10^-3 Hint: Write out the solubility equilibrium, the ICE table, and the Ksp expression in terms of ion concentration-
the solubility product (Ksp) for PbBr₂ is 9.81 * 10^(-9) with one decimal place past the decimal point.
The solubility equilibrium for PbBr₂ can be written as:
PbBr₂ (s) ⇌ Pb²⁺ (aq) + 2Br⁻ (aq)
Let's assume that 'x' is the molar solubility of PbBr₂ in moles per liter.
Using the stoichiometry of the reaction, we can write the initial, change, and equilibrium concentrations in an ICE (Initial-Change-Equilibrium) table:
PbBr₂ (s) ⇌ Pb²⁺ (aq) + 2Br⁻ (aq)
I: 0 0 0
C: -x +x +2x
E: x x 2x
The solubility product expression, Ksp, can be written as the product of the ion concentrations raised to their stoichiometric coefficients:
Ksp = [Pb²⁺] [Br⁻]²
Substituting the equilibrium concentrations from the ICE table, we have:
Ksp = x * (2x)² = 4x³
Given that the solubility of PbBr₂ is 0.00156 M, we can substitute this value into the Ksp expression:
Ksp = 4 * (0.00156)³ = 9.81 * 10^(-9)
Therefore, the solubility product (Ksp) for PbBr₂ is 9.81 * 10^(-9) with one decimal place past the decimal point.
To know more about solubility equilibrium related question visit:
https://brainly.com/question/17330140
#SPJ11
Given that a sterile feed containing 10 to 20 g/L of crude substrate at a rate of 85 L/h is applied for the industrial-scale production of protease enzymes via submerged fermentation in a CSTR. The gr
The amount of substrate supplied per hour can be calculated based on the substrate concentration and flow rate, providing a range of substrate quantities for the fermentation process.
The given information provides details about the composition of the sterile feed and the flow rate in the CSTR. The crude substrate concentration in the feed ranges from 10 to 20 g/L, indicating the amount of substrate present in each liter of the feed solution.
To calculate the amount of crude substrate being supplied per hour, we can multiply the substrate concentration by the flow rate:
Substrate supplied per hour = Crude substrate concentration x Flow rate
Substrate supplied per hour = (10-20 g/L) x 85 L/h
For a substrate concentration of 10 g/L:
Substrate supplied per hour = 10 g/L x 85 L/h = 850 g/h
For a substrate concentration of 20 g/L:
Substrate supplied per hour = 20 g/L x 85 L/h = 1700 g/h
These calculations give us the range of substrate being supplied to the CSTR for protease enzyme production.
The industrial-scale production of protease enzymes via submerged fermentation in a CSTR involves the application of a sterile feed containing 10 to 20 g/L of crude substrate at a rate of 85 L/h. The amount of substrate supplied per hour can be calculated based on the substrate concentration and flow rate, providing a range of substrate quantities for the fermentation process.
To know more about fermentation process, visit:
https://brainly.com/question/29670573
#SPJ11
"Synthesis gas may be produce by the catalyst reforming of methane with steam. The reactions are: CH4 (g)+H2O(g)→CO(g)+3H2 (g) A small plant is being to produce 600 mol/s of hydrogen (H2) by the reaction. 250 mol/s of Methane with 100 % of excess steam are fed to the heat exchanger at 150 °C and heated with superheated vapor. The superheated vapor inlet to the heat exchanger at 10 bar and 750 °C and leaved saturated at the same pressure. The mixture of methane and steam leaved the heat exchanger and inlet to the reactor at 600 °C. The products emerge from the reactor at 1000 °C. State any assumptions: Base the information above, do or answer the following: 1. Draw the diagram of the process. 2. Solve the mass balances. 3. Determine the CH4 conversion. 4. Determine the heat gained by the mixture of methane and steam in the heat exchanger [kW]. 5. Calculate the amount of superheated vapor fed to the heat exchanger [kg/s] 6. Determine the heat of reaction for the reaction at 25 °C in [kJ/mol] 7. Determine the heat lost/gained by the by the reactor [kW]
1. The process involves reforming methane with steam to produce synthesis gas. 2. Mass balances are solved to determine the reactant and product flow rates. 3. The CH4 conversion is calculated based on the reactant and product flow rates. 4. The heat gained by the mixture of methane and steam in the heat exchanger is determined.5. The amount of superheated vapor fed to the heat exchanger is calculated.6. The heat of reaction for the reforming reaction is determined. 7. The heat lost/gained by the reactor is calculated.
1. The diagram of the process involves a heat exchanger and a reactor. Methane and steam enter the heat exchanger, where they are heated with superheated vapor. The mixture then enters the reactor, and the products (synthesis gas) exit the reactor.
2. Mass balances are solved based on the given information. It is stated that 250 mol/s of methane with 100% excess steam are fed to the heat exchanger. Therefore, the flow rate of methane is 250 mol/s and the flow rate of steam is also 250 mol/s. The desired product is 600 mol/s of hydrogen (H2), so the flow rate of CO and H2 can be determined as well.
3. The CH4 conversion is calculated by comparing the initial moles of methane with the moles of methane that have reacted. In this case, all 250 mol/s of methane react, resulting in a 100% conversion.
4. The heat gained by the mixture of methane and steam in the heat exchanger can be determined using the equation Q = m * Cp * ΔT, where Q is the heat gained, m is the mass flow rate, Cp is the specific heat capacity, and ΔT is the temperature change. The specific heat capacity can be estimated based on the properties of methane and steam.
5. The amount of superheated vapor fed to the heat exchanger can be determined based on the energy balance. The energy gained by the mixture of methane and steam in the heat exchanger is equal to the energy supplied by the superheated vapor.
6. The heat of reaction for the reforming reaction at 25 °C can be determined using thermodynamic data and enthalpy calculations.
7. The heat lost/gained by the reactor can be calculated by considering the energy balance. The heat lost by the reactants entering the reactor is equal to the heat gained by the products leaving the reactor, taking into account any heat of reaction and the temperature change.
Learn more about methane : brainly.com/question/12645626
#SPJ11
Measurement of natural corrosion potential of buried pipe using saturated copper sulfate reference electrode. I got . Epipe -482 mVsce How much is this corrosion potential expressed by converting it to the standard hydrogen electrode potential? However, the standard potential value of the copper sulfate reference electrode is ESCE = +0.316 VSHE
To convert the corrosion potential expressed in saturated copper sulfate reference electrode (mVsce) to the standard hydrogen electrode potential (VSHE), you can use the following formula:
E(SHE) = E(sce) + E(ref)
where: E(SHE) is the potential with respect to the standard hydrogen electrode (VSHE) E(sce) is the potential with respect to the saturated copper sulfate reference electrode (mVsce) E(ref) is the reference potential of the saturated copper sulfate electrode (VSHE)
Given: E(sce) = -482 mVsce E(ref) = +0.316 VSHE
Converting the units of E(sce) to VSHE: E(sce) = -482 mVsce * (1 V/1000 mV) = -0.482 VSHE
Using the formula: E(SHE) = E(sce) + E(ref) E(SHE) = -0.482 VSHE + 0.316 VSHE
E(SHE) = -0.166 VSHE
Therefore, the corrosion potential expressed in terms of the standard hydrogen electrode potential is approximately -0.166 VSHE.
The corrosion potential, when converted to the standard hydrogen electrode potential, is approximately -0.166 VSHE.
To know more about corrosion, visit :
https://brainly.com/question/31313074
#SPJ11
Magnesium 5g Sodium 2.1g Silver sulfate 14.65g Calcium 17.0g Iron oxide 45.8g Oxygen 0.1g Water 0.5g Magnesium 7.56g Hydrochloric acid Carbon Magnesium oxide Sodium hydroxide 2.3g Magnesium sulfate 13.98g Calcium chloride 19.2g Iron 52.3g Hydrogen Silver HERE Hydrogen 0.99 Carbon dioxide 1.2g
The given list of substances comprises various elements and compounds. The quantities provided indicate the mass of each substance. Here is a breakdown of the substances and their properties:
1. Magnesium (5g): Magnesium is a chemical element with symbol Mg. It is a shiny, silver-white metal and is highly reactive. Magnesium is known for its low density and is commonly used in alloys and as a reducing agent in various chemical reactions.
2. Sodium (2.1g): Sodium is a chemical element with symbol Na. It is a soft, silvery-white metal and is highly reactive. Sodium is an essential mineral in our diet and is commonly found in table salt (sodium chloride).
3. Silver sulfate (14.65g): Silver sulfate is a compound composed of silver (Ag), sulfur (S), and oxygen (O). It is a white crystalline solid and is used in various applications, including photography, silver plating, and as a laboratory reagent.
4. Calcium (17.0g): Calcium is a chemical element with symbol Ca. It is a soft gray alkaline earth metal and is essential for the growth and maintenance of strong bones and teeth. Calcium is also involved in various physiological processes in the body.
5. Iron oxide (45.8g): Iron oxide refers to a family of compounds composed of iron (Fe) and oxygen (O). It occurs naturally as minerals such as hematite and magnetite. Iron oxide is widely used as a pigment in paints, coatings, and construction materials.
6. Oxygen (0.1g): Oxygen is a chemical element with symbol O. It is a colorless, odorless gas and is essential for supporting life on Earth. Oxygen is involved in various biochemical reactions, and its abundance in the atmosphere enables the process of respiration.
7. Water (0.5g): Water is a compound composed of hydrogen (H) and oxygen (O), with the chemical formula H2O. It is a transparent, odorless, and tasteless liquid that is essential for all known forms of life.
8. Hydrochloric acid: Hydrochloric acid (HCl) is a strong acid that consists of hydrogen (H) and chlorine (Cl). It is commonly used in various industrial and laboratory applications, such as cleaning, pickling, and pH regulation.
9. Carbon: Carbon is a chemical element with symbol C. It is a nonmetallic element and is the basis for all organic compounds. Carbon is essential for life and is the fundamental building block of many important molecules, including carbohydrates, proteins, and DNA.
10. Magnesium oxide: Magnesium oxide (MgO) is a compound composed of magnesium (Mg) and oxygen (O). It is a white solid and is commonly used as a refractory material, as a component of cement, and as an antacid.
11. Sodium hydroxide (2.3g): Sodium hydroxide (NaOH), also known as caustic soda, is a strong alkaline compound. It is composed of sodium (Na), oxygen (O), and hydrogen (H). Sodium hydroxide is widely used in the chemical industry for various purposes, including in the production of soaps, detergents, and paper.
12. Magnesium sulfate (13.98g): Magnesium sulfate (MgSO4) is a compound composed of magnesium (Mg), sulfur (S), and oxygen (O). It is commonly used as a drying agent, in the treatment of magnesium deficiency, and as a component in bath salts.
13. Calcium chloride (19.2g): Calcium chloride (CaCl2) is a compound composed of calcium (Ca) and chlorine (Cl). It is a white crystalline solid and is
For more questions on Oxygen, click on:
https://brainly.com/question/26073928
#SPJ8