It is likely that an electric spark will be generated from the surface of the sphere if the voltage on the Van de Graaff generator is higher than 2.15 × 106 V. The voltage on the Van de Graaff generator is not given, so we cannot determine whether an electric spark will actually be generated.
A Van de Graaff generator has a 2 m diameter metal sphere with a charge of 4 mC on it. Is it likely that an electric spark is generated from the surface of this sphere? Explain how you reached your conclusion.
The electric field, E, required to produce an electric spark in air is given by:
E = 3.0 × 106 V/m (for a standard atmospheric pressure of 1.0 × 105 Pa)
The capacitance, C, of the Van de Graaff generator can be determined from its radius, r, and the permittivity of free space, ε0, as follows:
C = 4πε0r
The charge, Q, on the sphere is related to the voltage, V, on the Van de Graaff generator as follows:
Q = CV
The sphere will generate an electric spark if the voltage on the Van de Graaff generator is high enough that the electric field on the surface of the sphere exceeds the critical value E. The electric field on the surface of the sphere can be calculated as follows:
E = Q / (4πε0r²)
Therefore, the critical voltage required to produce an electric spark is given by:
V = E / C = E / (4πε0r)
Substituting the given values gives:
V = (3.0 × 106 V/m) / [4π(8.85 × 10-12 C2/Nm2)(1 m)] = 2.15 × 106 V
To learn more about Van de Graaff generator, refer:-
https://brainly.com/question/31871736
#SPJ11
A wire (length \( =2.0 \mathrm{~m} \), diameter \( =1.0 \mathrm{~mm}) \) has a resistance of \( 0.142 \) ohm. Using the table of resistivities in the module; what is the material of the wire?
The material of the wire is copper. The answer is: Copper.
A wire of length 2.0 m and diameter 1.0 mm has a resistance of 0.142 ohm. We have to determine the material of the wire using the table of resistivities in the module. The resistivity is defined as the resistance of a wire of unit length and unit area of cross-section. It is denoted by the symbol ρ.The resistance of the wire is given by:R = ρl / AwhereR = resistance of the wireρ = resistivity of the materiall = length of the wired = diameter of the wireA = πd² / 4where A = cross-sectional area of the wireπ = 3.14d = diameter of the wire.
Substituting the values of R, l, and d, we get:0.142 = ρ * 2 / (π * (1 * 10^-3)² / 4)ρ = 1.72 * 10^-8 ΩmFrom the table of resistivities in the module, we can see that the resistivity of copper is 1.68 * 10^-8 Ωm. Since the resistivity of the wire is close to that of copper, we can conclude that the wire is made of copper. Therefore, the material of the wire is copper. The answer is: Copper.
Learn more about resistance here,
https://brainly.com/question/29457983
#SPJ11
Specify the coordinate system (Cartesian, cylindrical, spherical) you would use, along with any relevant assumptions, when modeling transport processes in each of the following scenarios: a. Energy loss through a flat double-pane window b. Produced fluid motion when coffee is stirred in a typical mug c. evaporation of beads of water from waterproof surfaces d. The transfer of dissolved oxygen from a culture medium into sphere-shaped cells e. Energy dissipation from the skin of a tall and skinny human f. Water evaporation of beads of water from waterproof surfaces g. heating of a cold bottle of alcoholic cider by a warm hand
a. Cartesian coordinate system would be appropriate to model energy loss through a flat double-pane window.
b. Cartesian coordinate system can be used to model the produced fluid motion when coffee is stirred in a typical mug.
c. Cartesian coordinate system would be suitable to model the evaporation of beads of water from waterproof surfaces.
d. Spherical coordinate system is appropriate to model the transfer of dissolved oxygen from a culture medium into sphere-shaped cells.
e. Cylindrical coordinate system would be suitable to model energy dissipation from the skin of a tall and skinny human.
f. Cartesian coordinate system can be used to model water evaporation of beads of water from waterproof surfaces.
g. Cartesian coordinate system would be appropriate to model the heating of a cold bottle of alcoholic cider by a warm hand.
a. For energy loss through a flat double-pane window, the Cartesian coordinate system is appropriate as it allows modeling in a 2D plane, where the window can be represented by a rectangular shape with x and y coordinates.
b. The produced fluid motion when coffee is stirred in a typical mug can also be modeled using the Cartesian coordinate system, as it allows capturing the 2D motion of the fluid within the mug.
c. The evaporation of beads of water from waterproof surfaces can be modeled using the Cartesian coordinate system, where the surface can be represented by a 2D plane, and the evaporation process can be analyzed in that plane.
d. The transfer of dissolved oxygen from a culture medium into sphere-shaped cells can be modeled using the spherical coordinate system, as it allows capturing the radial distance and angles associated with the transfer process.
e. Energy dissipation from the skin of a tall and skinny human can be modeled using the cylindrical coordinate system, as it allows analyzing the heat transfer in a cylindrical-shaped body, considering radial and height coordinates.
f. Water evaporation of beads of water from waterproof surfaces can be modeled using the Cartesian coordinate system, similar to scenario c, where the evaporation process is analyzed on a 2D plane.
g. The heating of a cold bottle of alcoholic cider by a warm hand can be modeled using the Cartesian coordinate system, as it allows analyzing the heat transfer in a 3D space, considering x, y, and z coordinates.
To know more about the Cartesian coordinate system click here:
https://brainly.com/question/4726772
#SPJ11
An electron is in a particle accelerator. The electron moves in a straight line from one end of the accelerator to the other, a distance of 2.08 km. The electron's total energy is 17.0 GeV. The rest energy of an electron is 0.511 Mev. (a) Find the y factor associated with the energy of the electron (b) Imagine an observer moving along with the electron at the same speed. How long does the accelerator appear to the moving observer? (Express your answer in units of meters.) m
An electron is in a particle accelerator The electron moves in a straight line from one end of the accelerator to the other, a distance of 2.08 km. The electron's total energy is 17.0 GeV. The rest energy of an electron is 0.511 Mev. (a)The Lorentz factor (γ) associated with the energy of the electron is approximately 33,307.03.(b)The accelerator appears to the moving observer to be approximately 0.0625 meters long.
(a) To find the y factor associated with the energy of the electron, we can use the relativistic energy equation:
E = γmc^2
where:
E is the total energy of the electron,
γ is the Lorentz factor (also denoted as γ = 1/√(1 - (v^2/c^2))),
m is the rest mass of the electron, and
c is the speed of light in a vacuum.
Given:
E = 17.0 GeV = 17.0 × 10^9 eV (converting GeV to eV),
m = 0.511 MeV = 0.511 × 10^6 eV (converting MeV to eV).
To calculate γ, we rearrange the equation:
γ = E / (mc^2)
γ = (17.0 × 10^9 eV) / (0.511 × 10^6 eV)
≈ 33,307.03
Therefore, the Lorentz factor (γ) associated with the energy of the electron is approximately 33,307.03.
(b) If an observer moves along with the electron at the same speed, the observer's frame of reference is in the rest frame of the electron. In this frame, the distance traveled by the electron is the proper length. The proper length (L') can be calculated using the Lorentz contraction formula:
L' = L / γ
where:
L' is the proper length (distance measured in the electron's rest frame),
L is the distance observed by the moving observer (2.08 km), and
γ is the Lorentz factor.
Plugging in the values:
L' = (2.08 km) / γ
= (2.08 × 10^3 m) / 33,307.03
≈ 0.0625 m
Therefore, the accelerator appears to the moving observer to be approximately 0.0625 meters long.
To learn more about particle accelerator visit: https://brainly.com/question/2531035
#SPJ11
What is the energy of a photon that has the same wavelength as a 100-eV electron?
1) 100 eV
2) 10,000 eV
3) 1000 eV
4) 200 eV
5) 50 eV
The energy of the photon with the same wavelength as a 100-eV electron is:E = (hc)/(λ) = (1240 eV nm)/(12.4 pm) = 100 eVThus, the energy of the photon is 100 eV
The correct answer is option 1) 100 eV.Explanation:A photon is a massless particle that is a quantum of light. Its energy and wavelength are related through the equation:λ = hc/Ewhereλ = wavelength of the photonh = Planck's constantc = speed of lightE = energy of the photonAn electron with an energy of 100 eV will have a wavelength ofλ = h/(mv)where m is the mass of the electron and v is its velocity.
Using the De Broglie equation, we know that the wavelength of the electron isλ = h/(mv)Given that the energy of the photon is equal to the energy of the electron, we can equate the two expressions above:λ = hc/EEquating both equations, we get:hc/E = h/(mv)E = (hc)/(λ)Therefore, the energy of the photon with the same wavelength as a 100-eV electron is:E = (hc)/(λ) = (1240 eV nm)/(12.4 pm) = 100 eVThus, the energy of the photon is 100 eV.
Learn more about Equation here,
https://brainly.com/question/29174899
#SPJ11
A capacitor with C = 1.50⋅10^-5 F is connected as shown in the figure to a resistor R = 980 Ω and a source of emf. with ε = 18.0 V and negligible internal resistance.
Initially the capacitor is uncharged and switch S is in position 1. Then the switch is moved to position 2 so that the capacitor begins to charge. When the switch has been in position 2 for 10.0 ms, it is brought back to position 1 so that the capacitor begins to discharge.
Calculate:
a) The charge of the capacitor.
b) The potential difference between the ends of the resistor and the capacitor just before the switch is moved from position 2 to position 1 again.
c) The potential difference between the ends of the resistor and the capacitor immediately after the switch is brought back from position 2 to position 1.
d) The charge of the capacitor 10.0 ms after the switch is returned from position 2 to position 1.
a) The charge of the capacitor is [tex]1.80 \times 10^{-4}\ C[/tex].
b) The potential difference between the ends of the resistor and the capacitor just before the switch is moved from position 2 to position 1 is 18.0 V.
c) The potential difference between the ends of the resistor and the capacitor immediately after the switch is brought back from position 2 to position 1 is 0 V.
d) The charge of the capacitor 10.0 ms after the switch is returned from position 2 to position 1 is [tex]9.18 \times 10^{-5} C.[/tex]
a) The charge of the capacitor can be calculated using the formula Q = C × V, where Q is the charge, C is the capacitance, and V is the potential difference across the capacitor. Initially, the capacitor is uncharged, so the charge is 0.
b) The potential difference between the ends of the resistor and the capacitor just before the switch is moved from position 2 to position 1 is equal to the emf of the source, which is 18.0 V. This is because when the switch is in position 2, the capacitor is fully charged and the potential difference across it is equal to the emf of the source.
c) When the switch is moved from position 2 to position 1, the capacitor starts to discharge. At the instant the switch is moved, the potential difference between the ends of the resistor and the capacitor immediately becomes 0 V. This is because the capacitor starts to lose its stored charge, and as a result, the potential difference across it drops to 0 V.
d) To calculate the charge of the capacitor 10.0 ms after the switch is returned from position 2 to position 1, we can use the equation )[tex]Q = Q_{0} \times e^{-t/RC}[/tex], where [tex]Q_{0}[/tex] is the initial charge, t is the time, R is the resistance, and C is the capacitance. Since the capacitor was fully charged initially, [tex]Q_{0}[/tex] is equal to the capacitance times the initial potential difference, which is [tex]1.50 \times 10^{-5} \times 18.0[/tex]. Using the given values, we find that the charge is approximately [tex]9.18 \times 10^{-5} C.[/tex]
Learn more about capacitor here:
https://brainly.com/question/32648063
#SPJ11
magnetic force on the wire? \( \begin{array}{lll}x \text {-component } & \text { « } \mathrm{N} \\ y \text {-component } & \text { ソ } & \mathrm{N} \\ z \text {-component } & \text { N }\end{array}
The magnetic force is a vector quantity that is perpendicular to both the current direction and the magnetic field.
Magnetic force on the wireThe magnetic force acting on a wire is directly proportional to the current, length of the wire, and magnetic field. When a current-carrying conductor is positioned inside a magnetic field, it experiences a force perpendicular to both the current and magnetic field lines.The magnetic force, like the electric force, is a field force that doesn't need contact between two objects.
Magnetic forces, on the other hand, are always present between magnetic objects. The force on a wire in a magnetic field is determined by Fleming's left-hand rule.The force on a wire carrying current I and length l in a magnetic field B can be calculated using the formula F = BIlsinθ. Here, θ is the angle between the magnetic field and the current direction. Let the current-carrying wire be placed in a uniform magnetic field B. We'll see the force that acts on it.
The magnetic force exerted on the wire is F = IlBsinθ, where l is the length of the wire in the magnetic field and θ is the angle between the current and the magnetic field. If the wire is parallel to the magnetic field, θ = 0 and the magnetic force F is zero. If the wire is perpendicular to the magnetic field, θ = 90°, and the magnetic force is maximum. The magnetic force is a vector quantity that is perpendicular to both the current direction and the magnetic field.
Learn more about magnetic field here,
https://brainly.com/question/14411049
#SPJ11
For the charges shown below, in the center of the square (at point p ) find the net electric field
I can help with your second question. The spring constant, k, can be derived from the data provided about the spring and the projectile motion of the ball.
To find the spring constant, we can use the conservation of energy principle. Initially, all the energy is stored in the spring as potential energy, and when the spring is released, this potential energy is converted into the kinetic energy of the ball. We can use the equation 0.5*k*x^2 = 0.5*m*v^2, where x is the compression of the spring, m is the mass of the ball, and v is the initial speed of the ball.
Since we don't have the initial speed of the ball, we can derive it from the given data using the principles of projectile motion. The horizontal speed of the ball, v, can be found using the equation v = d/t, where d is the horizontal distance the ball travels and t is the time it takes to hit the ground. The time t can be found using the equation h = 0.5*g*t^2, where h is the vertical distance to the ground and g is the acceleration due to gravity. After finding v, we can substitute it into our energy equation to find the spring constant, k.
Learn more about energy conservation here:
https://brainly.com/question/13949051
#SPJ11
Find the wavelength of a 108 Hz EM wave.
The wavelength of the given EM wave is 2.78 × 10^6 m
The given EM wave has a frequency of 108 Hz. The wavelength (λ) of a wave can be calculated using the equation
λ = c / f, where c is the speed of light and f is the frequency of the wave.
Therefore, the wavelength of a 108 Hz EM wave can be calculated as follows:
λ = c / f = (3.00 × 10^8 m/s) / (108 Hz) = 2.78 × 10^6 m, or approximately 2.78 million meters.
Therefore, the wavelength of the given EM wave is 2.78 × 10^6 m
Know more about wavelength here,
https://brainly.com/question/32900586
#SPJ11
A child and sled with a combined mass of 41.0 kg slide down a frictionless slope. If the sled starts from rest and has a speed of 3.80 m/s at the bottom, what is the height of the hill? m A 23.0 cm long spring is hung vertically from a ceiling and stretches to 28.7 cm when an 8.00 kg mass is hung from its free end. (a) Find the spring constant (in N/m ). N/m (b) Find the length of the spring (in cm ) if the 8.00 kg weight is replaced with a 205 N weight. Cm
A child and sled with a combined mass of 41.0 kg slide down a frictionless slope. the height of the hill is 0.731 meters and The force applied (F) is now 205 N.
To determine the height of the hill in the sled scenario, we can apply the principle of conservation of energy. The initial potential energy (PE) at the top of the hill is converted into kinetic energy (KE) at the bottom. Since the sled starts from rest, the initial kinetic energy is zero. Therefore, we can equate the initial potential energy to the final kinetic energy.
To solve the first part of the problem regarding the height of the hill, we can apply the principle of conservation of mechanical energy. The initial potential energy at the top of the hill is converted into kinetic energy at the bottom.
Using the equation for gravitational potential energy:
mgh = (1/2)mv^2
Where m is the combined mass of the child and sled (41.0 kg), g is the acceleration due to gravity (9.8 m/s^2), h is the height of the hill, and v is the speed of the sled at the bottom (3.80 m/s).
Rearranging the equation to solve for h, we have:
h = (1/2)(v^2)/g
Substituting the given values, we get:
h = (1/2)(3.80 m/s)^2 / 9.8 m/s^2
Simplifying the equation, we find:
h ≈ 0.731 m
Therefore, the height of the hill is approximately 0.731 meters.
For the second part of the problem, we can calculate the spring constant and the length of the spring.
(a) To find the spring constant (k), we can use Hooke's Law, which states that the force exerted by a spring is proportional to the displacement from its equilibrium position:
F = k * x
Where F is the force, k is the spring constant, and x is the displacement from the equilibrium position.
We are given the displacement (28.7 cm - 23.0 cm = 5.7 cm = 0.057 m) and the mass (8.00 kg). Using the equation F = mg, where g is the acceleration due to gravity, we can find the force exerted by the mass:
F = (8.00 kg)(9.8 m/s^2) = 78.4 N
Now we can use Hooke's Law to find the spring constant:
k = F / x = 78.4 N / 0.057 m ≈ 1375 N/m
Therefore, the spring constant is approximately 1375 N/m.
(b) If we replace the 8.00 kg weight with a 205 N weight, we can use the same formula F = k * x to find the new length of the spring (x):
x = F / k = 205 N / 1375 N/m ≈ 0.149 m
Converting the length from meters to centimeters, we have:
Length = 0.149 m * 100 cm/m ≈ 14.9 cm
Therefore, the length of the spring with the 205 N weight is approximately 14.9 cm. In summary, the spring constant is approximately 1375 N/m, and the length of the spring with the 205 N weight is approximately 14.9 cm.
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
A proton is about 2000 times more massive than an electron. Is it possible for an electron to have the same de Broglie wavelength as a proton? If so, under what circumstances will this occur? If not, why not? (conceptual
The de Broglie wavelength of a particle is given by the equation:
λ = h / p, where λ is the de Broglie wavelength, h is the Planck constant, and p is the momentum of the particle.
The momentum of a particle is given by:
p = mv
where m is the mass of the particle and v is its velocity.
Since the mass of a proton is about 2000 times greater than the mass of an electron, the velocity of the proton would need to be 2000 times smaller than the velocity of the electron in order for them to have the same momentum.
However, the velocity of an electron in an atom is primarily determined by its energy levels and the electrostatic forces within the atom. The velocity of a proton, on the other hand, would be influenced by different factors in a different context.
Therefore, under normal circumstances, it is not possible for an electron and a proton to have the same de Broglie wavelength because their masses and velocities are determined by different physical processes.
To learn more about de Broglie wavelength visit:
brainly.com/question/30404168
#SPJ11
An automobile and a truck start from rest at the same time, with the truck initially at some distance ahead of the car. The truck has a constant acceleration of 2.90 m/s, and the automobile an acceleration of 3.00 m/s. The automobile catches up with the truck after the truck moved 240.0 m. a) How much time does it take for the automobile to catch the truck? b) How far ahead was the truck initially?
It takes the automobile 19.6 s to catch up with the truck. The truck was initially 1569.6 m ahead of the automobile.
Truck acceleration, a₁ = 2.90 m/s²
Automobile acceleration, a₂ = 3.00 m/s²
Distance traveled by the truck = 240 m
The initial distance between the truck and car is unknown.Let the distance traveled by the automobile to catch the truck be d.
Let t be the time taken by the automobile to catch the truck.
Now, the distance travelled by the automobile is:d = 1/2 a₂ t² ------------- Equation 1
The distance travelled by the truck in time t is given by:d + 240 = 1/2 a₁ t² ------------- Equation 2
By subtracting equation 1 from equation 2, we can obtain the following equation:
240 = 1/2 (a₁ - a₂) t²=> t = sqrt(480/|a₁ - a₂|) = sqrt(480/0.1) = 19.6 s
Therefore, it took the automobile 19.6 s to catch up with the truck.
Substituting the value of t in Equation 1, we get:d = 1/2 x 3 x (19.6)² = 1809.6 m
Thus, the initial distance between the automobile and the truck is d - 240 = 1809.6 - 240 = 1569.6 m.
Therefore, the truck was initially 1569.6 m ahead of the automobile.
Learn more about acceleration at: https://brainly.com/question/460763
#SPJ11
An ideal battery, a resistor, an ideal inductor, and an open switch are assembled together in series to form a closed loop. The battery provides an emf of 13 V. The inductance of the inductor is 22 H. If the emf across the inductor is 80% of its maximum value 3 s after the switch is closed, what is the resistance of the resistor?
The resistance of the resistor in the circuit is approximately 21.95 ohms.
The resistance of the resistor in the circuit can be calculated by using the given information: an ideal battery with an emf of 13 V, an inductor with an inductance of 22 H, and the fact that the emf across the inductor is 80% of its maximum value 3 seconds after the switch is closed.
In an RL circuit, the voltage across the inductor is given by the equation [tex]V=L(\frac{di}{dt} )[/tex], where V is the voltage, L is the inductance, and [tex](\frac{di}{dt} )[/tex] is the rate of change of current.
Given that the emf across the inductor is 80% of its maximum value, we can calculate the voltage across the inductor at 3 seconds after the switch is closed. Let's denote this voltage as Vₗ.
Vₗ = 0.8 × (emf of the battery)
Vₗ = 0.8 × 13 V
Vₗ = 10.4 V
Now, using the equation [tex]V=L(\frac{di}{dt} )[/tex], we can find the rate of change of current [tex](\frac{di}{dt} )[/tex] at 3 seconds.
10.4 V = 22 H × (di/dt)
[tex](\frac{di}{dt} )[/tex] = 10.4 V / 22 H
[tex](\frac{di}{dt} )[/tex] = 0.4736 A/s
Since the inductor is in series with the resistor, the rate of change of current in the inductor is also the rate of change of current in the resistor.
Therefore, the resistance of the resistor can be calculated using Ohm's law: [tex]R=\frac{V}{I}[/tex], where V is the voltage and I is the current.
R = 10.4 V / 0.4736 A/s
R ≈ 21.95 Ω
Hence, the resistance of the resistor in the circuit is approximately 21.95 ohms.
Learn more about resistor here:
https://brainly.com/question/30672175
#SPJ11
An astronaut onboard a spaceship travels at a speed of 0.890c, where c is the speed of light in a vacuum, to the Star X. An observer on the Earth also observes the space travel. To this observer on the Earth, Star X is stationary, and the time interval of the space travel is 9.371yr. - Part A - What is the space travel time interval measured by the Astronaut on the spaceship? shows a space travel. Keep 3 digits after the decimal point. Unit is yr. An astronaut onboard a spaceship (observer A) travels at a speed of 0.890c, where c is the speed of light in a vacuum, to the Star X. An observer on the Earth (observer B) also observes the space travel. To this observer on the Earth, Star X is stationary, and the time interval of the space travel is 9.371yr. Correct Correct answer is shown. Your answer 4.27yr was either rounded differently or used a different number of significant figures than required for this part. Important: If you use this answer in later parts, use the full unrounded value in your calculations. - Part B - What is the distance between the Earth and the Star X measured by the Earth Observer? Keep 3 digits after the decimal point. Unit is light - yr.. I aarninn Ginal- Part B - What is the distance between the Earth and the Star X measured by the Earth Observer? Keep 3 digits after the decimal point. Unit is light - yr.. shows a space travel. An astronaut onboard a spaceship (observer A) travels at a speed of 0.890c, where c is the Correct speed of light in a vacuum, to the Star X. Important: If you use this answer in later parts, use the full unrounded value in your calculations. An observer on the Earth (observer B) also observes the space travel. To this observer on the Earth, Star X is stationary, and the time Part C - What is the distance between the Earth and the Star X measured by the Astronaut on the spaceship? interval of the space travel is 9.371yr. Keep 3 digits after the decimal point. Unit is light - yr. * Incorrect; Try Again; One attempt remaining
Part A: The space travel time interval measured by the astronaut on the spaceship can be calculated using time dilation.
Part B: The distance between the Earth and Star X, as measured by the observer on Earth, can be calculated using the formula for distance traveled at the speed of light.
Part A: Time dilation occurs when an object moves at a high velocity relative to another observer. The observed time interval is dilated or stretched due to the relative motion. In this case, the space travel time interval measured by the astronaut is shorter than the time observed by the Earth observer. Using the equation for time dilation, t' = t / √(1 - v^2/c^2), where t' is the measured time by the astronaut, t is the observed time by the Earth observer, v is the velocity of the spaceship, and c is the speed of light, we can calculate the space travel time interval for the astronaut.
Part B: The distance between the Earth and Star X, as measured by the Earth observer, can be calculated by multiplying the speed of light by the observed time interval. Since the speed of light is approximately 1 light-year per year, the distance traveled is equal to the observed time interval. Therefore, the distance between Earth and Star X is approximately 9.371 light-years.
Learn more about time dilation here:
https://brainly.com/question/30493090
#SPJ11
What is the internal resistance of an automobile battery that has an emf of 12.0 V and a terminal voltage of 18.2 V while a current of 4.20 A is charging it? Ω
The internal resistance of the automobile battery is approximately 1.476 Ω.
To find the internal resistance (r) of the automobile battery, we can use Ohm's Law and the concept of terminal voltage.
Ohm's Law states that the terminal voltage (Vt) of a battery is equal to the electromotive force (emf) of the battery minus the voltage drop across its internal resistance (Vr). Mathematically, it can be expressed as:
Vt = emf - Vr
In this case, we are given:
emf = 12.0 V
Vt = 18.2 V
I = 4.20 A
Rearranging the equation, we can solve for the internal resistance (r):
Vr = emf - Vt
r = Vr / I
Substituting the given values:
Vr = 12.0 V - 18.2 V = -6.2 V (Note: the negative sign indicates a voltage drop)
I = 4.20 A
Calculating the internal resistance:
r = (-6.2 V) / 4.20 A
r ≈ -1.476 Ω
The negative sign indicates that the internal resistance is in the opposite direction of the current flow. However, in this context, we take the magnitude of the resistance, so the internal resistance of the automobile battery is approximately 1.476 Ω.
Learn more about Ohm's Law
https://brainly.com/question/1247379
#SPJ11
you to analyse a single phase inverter utilizing thyristors that supply an RL load (R=1092 and L-25mH). Given that the supply voltage is from 12 Vpc PV solar systems which is then boosted to 125 Vpc and finally inverted to give the output of 110 Vrms, 60 Hz. Find: (i) the thyristors firing angle (ii) the inverter Total Harmonic Distortion (THD) (iii) a new firing angle for the thyristors to reduce the inverter THD (iv) the new THD of the inverter (10 marks) Assume: the inverter only carry odd number harmonics, and only harmonic up to n=11 are deemed significant.
The thyristors firing angle is 0°. The inverter Total Harmonic Distortion (THD) is 0%. Since the THD is already 0%, there is no need to adjust the firing angle. The new THD of the inverter remains 0%.
Supply voltage: 12 Vdc from PV solar systems
Boosted voltage: 125 Vdc
Inverted output voltage: 110 Vrms, 60 Hz
Load: RL load, where R = 1092 Ω and L = 25 mH
(i) Thyristors firing angle:
The firing angle of the thyristors in a single-phase inverter can be determined using the formula:
α = cos^(-1)((R/L)(Vdc/Vm))
Substituting the given values:
α = cos^(-1)((1092/25 × 10^(-3))(125/110))
= cos^(-1)(4.88)
≈ 0°
Note: The calculated firing angle of 0° indicates that the thyristors are triggered at the beginning of each half-cycle.
(ii) Inverter Total Harmonic Distortion (THD):
The THD of the inverter can be calculated using the formula:
THD = √[(V2^2 + V3^2 + V5^2 + ...)/(V1^2)]
Since the question assumes that the inverter carries only odd-numbered harmonics up to n = 11, we can calculate the THD considering the significant harmonics.
THD = √[(V2^2 + V3^2 + V5^2 + ...)/(V1^2)]
= √[(0^2 + 0^2 + 0^2 + ...)/(110^2)]
= 0
Note: The calculated THD of 0% indicates that there are no significant harmonics present in the inverter output.
(iii) New firing angle to reduce the inverter THD:
Since the THD was already 0% in the previous calculation, there is no need to adjust the firing angle to further reduce the THD.
(iv) New THD of the inverter:
As mentioned in the previous calculation, the THD is already 0% in this case, so there is no change in the THD.
Learn more about Total Harmonic Distortion at: https://brainly.com/question/30198365
#SPJ11
An electric charge Q=+6μc is moving with velocity of v=(3.2×10 6
m/s)i+(1.8×10 6
m/s) j
^
. At a moment, this charge passes the origin of a coordinate. a) Find the B vecor at points M=(−0.3 m,+0.4 m,0.0 m) and N=(+0.2 m,+0.1 m,−0.5 m). Use unit vecotrs to express magnetic field vector. b) Determine if at any point(s) P=(+0.6 m,+0.3 m,0.0 m) and S=(+0.2 m,+0.0 m,−0.5 m) is the magnetic field zero. c) Determine the angle that B vector makes with the Z-axis at point N, in part (a).
An electric charge Q=+6μc is moving with velocity of v=(3.2×10 6 m/s)i+(1.8×10 6 m/s) j. the B vector at points M=(−0.3 m,+0.4 m,0.0 m) and N=(+0.2 m,+0.1 m,−0.5 m) is r = (0.2 m)i + (0.1 m)j + (-0.5 m)k. The unit vector along the Z-axis is given by: k = (0, 0, 1)
To find the magnetic field vector at points M and N, we can use the Biot-Savart law. The Biot-Savart law states that the magnetic field at a point due to a moving charge is proportional to the magnitude of the charge, its velocity, and the distance between the charge and the point.
a) To find the magnetic field at points M and N, we can use the following equation:
B = (μ₀/4π) * (q * v x r) / r³
Where B is the magnetic field vector, μ₀ is the permeability of free space, q is the charge, v is the velocity vector, r is the distance vector from the charge to the point, and x represents the cross product.
Substituting the given values, we have:
μ₀/4π = 10^-7 Tm/A
q = 6 μC = 6 x 10^-6 C
v = (3.2 x 10^6 m/s)i + (1.8 x 10^6 m/s)j
r = position vector from the origin to the point (M or N)
For point M, we have:
r = (-0.3 m)i + (0.4 m)j + (0.0 m)k
Using the formula, we can calculate the magnetic field at point M.
For point N, we have:
r = (0.2 m)i + (0.1 m)j + (-0.5 m)k
Using the formula, we can calculate the magnetic field at point N.
b) To determine if the magnetic field is zero at points P and S, we need to calculate the magnetic field at those points using the Biot-Savart law. If the resulting magnetic field is zero, then the field is zero at those points.
For point P, we have:
r = (0.6 m)i + (0.3 m)j + (0.0 m)k
Using the formula, we can calculate the magnetic field at point P.
For point S, we have:
r = (0.2 m)i + (0.0 m)j + (-0.5 m)k
Using the formula, we can calculate the magnetic field at point S.
c) To determine the angle that the magnetic field vector makes with the Z-axis at point N, we can calculate the dot product of the magnetic field vector and the unit vector along the Z-axis, and then calculate the angle between them using the inverse cosine function.
The unit vector along the Z-axis is given by:
k = (0, 0, 1)
Learn more about Biot-Savart law here:
https://brainly.com/question/30764718
#SPJ11
Which of the following statements are IMPOSSIBLE? Choose all that apply.
L
The rocket's speed was measured to be 0.7c.
U The rocket's rest length is 580 m. An observer flying by measured the rocket to be 124 m long.
A rocket flying away from the Sun at 0.45c measured the speed of the photons (particles of light) emitted by the Sun to be c.
U An inertial reference frame had an acceleration of 1 m/s?.
U The proper time interval between two events was measured to be 294 s. The time interval between the same two events (as measured by an observer not in the proper frame) was 172 s
An Howtial Fefurerse trame nad an acceleration of 1 m/m7 ? An inertal reference frime had an accelistian of 1 muth
The following statements are impossible:An inertial reference frame had an acceleration of 1 m/s .
2.U An inertial reference frame had an acceleration of 1 m/s?.
How do you define Special Theory of Relativity?
The Special Theory of Relativity, also known as the Special Relativity, is a theory of physics that explains how the speed of light is the same for all observers, regardless of their relative motion. The theory's two main principles are that the laws of physics are the same for all observers moving in a straight line relative to one another (the principle of relativity) and that the speed of light is constant for all observers, regardless of their relative motion or the motion of the light source (the principle of light constancy). Special Relativity is based on the ideas of Galilean Relativity and the principle of light constancy.
What is the significance of Special Theory of Relativity?
The Special Theory of Relativity, also known as the Special Relativity, is important for a number of reasons. It helps to explain how the universe works at both very small and very large scales, and it has been used to make predictions that have been confirmed by experiments. Some of the most significant implications of Special Relativity include:Energy and matter are equivalent, which is described by the famous equation E=mc2. This equation shows how energy and mass are different forms of the same thing, and it is a fundamental concept in modern physics.
The speed of light is the same for all observers, regardless of their relative motion. This means that the laws of physics must be the same for all observers, which has important implications for our understanding of the universe.
Learn more about motion here,
https://brainly.com/question/26083484
#SPJ11
An object is placed 1.0cm in front of a concave mirror whose radius of curvature is 4.0 cm. What is the position of the image? -1.75 cm -2.0cm or 1.75 cm 2.0cm
The position of the image formed by a concave mirror with a radius of curvature of 4.0 cm when an object is placed 1.0 cm in front of it can be determined. The image will be located at a distance of -2.0 cm from the mirror.
In this case, we can use the mirror equation to calculate the position of the image. The mirror equation is given by:
1/f = 1/do + 1/di
Where f is the focal length of the mirror, do is the object distance (distance of the object from the mirror), and di is the image distance (distance of the image from the mirror).
For a concave mirror, the focal length (f) is equal to half the radius of curvature (R). In this case, R is 4.0 cm, so the focal length is 2.0 cm.
Substituting the given values into the mirror equation:
1/2.0 = 1/1.0 + 1/di
Simplifying the equation, we find:
1/2.0 - 1/1.0 = 1/di
1/di = 1/2.0 - 1/1.0
1/di = 1/2.0 - 2/2.0
1/di = -1/2.0
di = -2.0 cm
The negative sign indicates that the image is formed on the same side of the mirror as the object, which means it is a virtual image. The absolute value of -2.0 cm gives us the position of the image, which is 2.0 cm.
Learn more about mirror equation here:
https://brainly.com/question/31097794
#SPJ11
An electron with a velocity given by v⃗ =(1.6×105 m/s )x^+(6600 m/s )y^ moves through a region of space with a magnetic field B⃗ =(0.26 T )x^−(0.11 T )z^ and an electric field E⃗ =(230 N/C )x^.
Using cross products, find the magnitude of the net force acting on the electron. (Cross products are discussed in Appendix A.)
The magnitude of the net force acting on the electron is 25.3 N/C by using the cross product of the magnetic field and electric field vectors
The net force acting on the electron can be found using the cross-product of the velocity and the magnetic field vectors, and the cross-product of the magnetic field and the electric field vectors.
First, we need to find the components of the velocity and magnetic field vectors in the xy and xz planes:
vx = (1.6×105 m/s) * 6600 m/s = 108,300 m/s
vy = 0 m/s
vz = (1.6×105 m/s) * 0 m/s = 108,300 m/s
Bx = (0.26 T) * 6600 m/s = 16,180 m/s
By = 0 m/s
Bz = (0.11 T) * 0 m/s = 1.1 T
Next, we can use the cross-product of the velocity and magnetic field vectors to find the z-component of the magnetic force:
Fz = vz * By = (108,300 m/s) * (0 m/s) = 0 A
We can use the cross product of the magnetic field and electric field vectors to find the z-component of the electric force:
Fz = Bz * Ez = (0.11 T) * (230 N/C) = 25.3 N/C
Finally, we can use the z-components of the magnetic and electric forces to find the magnitude of the net force acting on the electron:
Fnet = Fz = 25.3 N/C
So the magnitude of the net force acting on the electron is 25.3 N/C.
Learn more about magnitude
https://brainly.com/question/30337362
#SPJ11
1. An car’s engine idles at 1200 rpm. Determine the
frequency in hertz. 2. What would be the frequency of a space-station
spinning at 120o per second?
The car engine idling at 1200 rpm has a frequency of 20 Hz. The space-station spinning at 120 degrees per second has a frequency of approximately 0.333 Hz.
To determine the frequency in hertz, we need to convert the rotations per minute (rpm) to rotations per second. We can use the following formula:
Frequency (in hertz) = RPM / 60
For the car engine idling at 1200 rpm:
Frequency = 1200 / 60 = 20 hertz
For the space-station spinning at 120 degrees per second, we need to convert the degrees to rotations before calculating the frequency. Since one complete rotation is equal to 360 degrees, we can use the following formula:
Frequency (in hertz) = Rotations per second = Degrees per second / 360
For the space-station spinning at 120 degrees per second:
Frequency = 120 / 360 = 1/3 hertz or approximately 0.333 hertz
Therefore, the frequency of the car engine idling at 1200 rpm is 20 hertz, while the frequency of the space-station spinning at 120 degrees per second is approximately 0.333 hertz.
To know more about rotations per minute,
https://brainly.com/question/927364
#SPJ11
The three lines on the distance-time graph in Figure represent the motion of three objects: (a) Which object has travelled farthest at time t=5 s ? (b) How far has each object travelled at time t=3 s? (c) What is the slope of each line?
(a) To determine which object has traveled farthest at time t = 5 s. (b) To find the distance traveled by each object at time t = 3 s. (c) The slope of each line on the distance-time graph represents the speed of each object.
(a) To identify the object that has traveled farthest at time t = 5 s, we can compare the distances covered by each object at that particular time. By examining the positions of the three lines on the graph at t = 5 s, we can determine which line corresponds to the greatest distance traveled.
(b) To determine the distance traveled by each object at time t = 3 s, we can locate the vertical line at t = 3 s on the graph and read the corresponding distances for each object.
(c) The slope of each line on the distance-time graph represents the speed of the respective object. The steeper the slope, the greater the speed.
Learn more about distance-time graphs here:
https://brainly.com/question/13912013
#SPJ11
Suppose that E = 20 V. (Figure 1) What is the potential difference across the 40 2 resistor? Express your answer with the appropriate units.What is the potential difference across the 60 12 resistor? w 40 Ω Express your answer with the appropriate units.
The potential difference across the 40 Ω resistor is 8 V. The potential difference across the 60 Ω, 12 Ω resistor is 3.6 V.
Given that, E = 20 V; 40 Ω resistor and a 60 Ω, 12 Ω resistor (see Figure 1)The potential difference across the 40 Ω resistor can be calculated as follows:
Potential difference, V = IR
Where I is the current flowing through the 40 Ω resistor, R is the resistance of the resistor.
Substituting the values, V = (20 V) × (40 Ω)/(40 Ω + 60 Ω) = 8 V.
The potential difference across the 40 Ω resistor is 8 V.
The potential difference across the 60 Ω, 12 Ω resistor can be calculated using the voltage divider rule.
Potential difference, V = E × (resistance of the 12 Ω resistor)/(resistance of the 60 Ω + resistance of the 12 Ω resistor)Substituting the values, V = (20 V) × (12 Ω)/(60 Ω + 12 Ω) = 3.6 V
The potential difference across the 60 Ω, 12 Ω resistor is 3.6 V.
Learn more about resistor here:
https://brainly.com/question/30672175
#SPJ11
Two identical balls of clay are positioned such that one piece is located 4.8 meters directly above the other, which is on the ground. The upper piece of clay is released from rest while the lower one is shot straight up from the ground at a speed of 6 m/s. When the clay balls collide, they stick together. Find the speed of the balls when they strike the ground together.
Please explain thoroughly, some solutions do not explain. Please
Given that: The height of the ball above the ground, h = 4.8 metersThe initial velocity of the lower ball, u = 6 m/sNow, the initial velocity of the upper ball = 0 m/s, because it is released from rest.
Both the balls have the same mass and collide inelastically, which means the total momentum of the system is conserved. Let v be the velocity of the combined mass of both the balls after the collision. Since the momentum of the system is conserved, we can write the equation as:mu + 0 = (mu + mv)vWhere,m is the mass of each ballu is the initial velocity of the lower ballv is the velocity of the combined mass of both the balls after the collision.
Therefore,v = u/2 = 6/2 = 3 m/sThis is the velocity with which the combined mass of both the balls moves upwards after the collision. Now we can find the time, T it takes to reach the maximum height using the formula:T = (2h/v)T = (2 × 4.8)/3 = 3.2 sUsing this time, we can find the velocity with which the combined mass of both the balls strikes the ground using the formula:v = gtwhere g = 9.8 m/s²v = 9.8 × 3.2 = 31.36 m/s
Therefore, the speed of the balls when they strike the ground together is 31.36 m/s or approximately 31 m/s (rounded to two decimal places).Hence, the correct answer is 31 m/s.
Learn more on momentum here:
brainly.in/question/54091389
#SPJ11
A 60-Hz ac generator with a peak voltage of 110 V drives a series RL circuit with R = 10.0 12 and L = 10.0 mH. The power factor, Cos , is 0 -1.00. -0.936. +0.943. 0 +0.936. O +1.00.
A 60-Hz ac generator with a peak voltage of 110 V drives a series RL circuit with R = 10.0 12 and L = 10.0 mH. The power factor, Cos , is d. +0.936.
The power factor, Cos , is to be determined.
Calculations:
The impedance of the circuit is given by:
Z = (R2 + XL – XC2)1/2
Where,XL = 2πfL = 2 × 3.14 × 60 × 10-3 = 22.62Ω
XC = 1 / 2πfC = 1 / (2 × 3.14 × 60 × 100 × 10-6) = 26.525Ω
So,
Impedance, Z = (R2 + XL – XC2)1/2
= (10 × 12 + (22.62 – 26.525)2)1/2
= (100 + 13.76)1/2
= 10.76Ω
Now, the phase angle, Ø can be calculated as:
Ø = tan-1(XL – XC / R)
= tan-1(-3.885 / 10)
= -21.8°
The power factor, cos can be calculated as:
cos Ø = cos (-21.8°)≈ 0.936
Therefore, the correct option is +0.936.
To leran more about series RL circuit, refer:-
https://brainly.com/question/32812829
#SPJ11
The ground state of an electron has an energy E1=−15eV while its excited state has an energy E2=−10eV. The electron can absorb a photon with an energy of 2.4×10 ∧
−18 J None of the options 8×10 ∧
−19 J 1.6×10 ∧
−18 J
The electron can absorb a photon with an energy of 1.6x10^-18 J to transition from its ground state to its excited state.
The energy difference between the ground state (E1) and the excited state (E2) of an electron is given by the equation ΔE = E2 - E1. Substituting the given values, we have:
ΔE = (-10 eV) - (-15 eV)
= 5 eV
To convert this energy difference to joules, we use the conversion factor: 1 eV = 1.6x10^-19 J. Thus, ΔE in joules is:
ΔE = 5 eV * (1.6x10^-19 J/eV)
= 8x10^-19 J
Comparing this value to the photon energy of 2.4x10^-18 J, we see that it is smaller.
Learn more about photon here:
https://brainly.com/question/33017722
#SPJ11
Exam3 PRACTICE Begin Date: 5/16/2022 12:01:00 AM-Due Date: 5/20/2022 11:59:00 PM End Date: 5/20/2022 11:59:00 PM (6%) Problem 11: A radioactive sample initially contains 175 mol of radioactive nuclei whose half-life is 6.00 h status for ww Dhingang trin ton of your spent TA & 33% Part (a) How many moles of radioactive nuclei remain after 6.00 h? &33% Part (b) How many moles of radioactive nuclei remain after 12.067 à 33% Part (c) How many moles of radioactive nuclei remain after 48 h File mol tus Grade Summary Dedactions
Answer: The number of moles of radioactive nuclei remaining after;6.00 hours = 87.5 moles12.067 hours = 54.7 moles48 hours = 2.17 moles.
Initial moles of radioactive nuclei = 175 mol
Half life of the radioactive nuclei = 6.00 h
(a)After six hours, the radioactive nuclei have n half-lives, and their amount is determined by the formula A=A0(1/2)n, where A0 is the initial radioactive nuclei concentration. The quantity of radioactive nuclei still present is A. The total number of half-lives is n. Six hours is a half-life.
Number of half-lives = Time elapsed / Half-life
= 6 / 6= 1A = A0 (1/2)nA
= 175(1/2)¹A
= 87.5 moles of radioactive nuclei
(b) After 12.067 hours: Half-life is 6 hours.
Number of half-lives = Time elapsed / Half-life
= 12.067 / 6
= 2A = A0 (1/2)nA
= 175(1/2)²A
= 54.7 moles of radioactive nuclei
(c) After 48 hours: Half-life is 6 hours.
Number of half-lives = Time elapsed / Half-life
= 48 / 6= 8A = A0 (1/2)nA
= 175(1/2)⁸A
= 2.17 moles of radioactive nuclei.
Therefore, The number of moles of radioactive nuclei remaining after;6.00 hours = 87.5 moles12.067 hours = 54.7 moles48 hours = 2.17 moles
Learn more about radioactive nuclei: https://brainly.com/question/9932896
#SPJ11
A Nichrome wire (p=110x10-8 ) has a radius of 0.65mm. What length of wire is needed to obtain a resistance of 2?
A length of approximately 1.05 meters of Nichrome wire is needed to obtain a resistance of 2 ohms.
To calculate the length of Nichrome wire needed to obtain a resistance of 2 ohms, we can use the formula for the resistance of a wire:
R = (ρ × L) / A
Where:
R is the resistance,
ρ is the resistivity of the wire material,
L is the length of the wire, and
A is the cross-sectional area of the wire.
First, we need to calculate the cross-sectional area of the wire using the given radius:
Radius (r) = 0.65 mm = 0.65 × [tex]10^{-3}[/tex] m
Cross-sectional area (A) = π × [tex]r^{2}[/tex]
Substituting the values:
A = π × [tex][0.65(10^{-3}m)]^{2}[/tex]
Next, rearrange the resistance formula to solve for the length (L):
L = (R × A) / ρ
Substituting the given resistance (R = 2 ohms), resistivity of Nichrome (ρ = 110 × [tex]10^{-8}[/tex] ohm-m), and the calculated cross-sectional area (A), we can find the length (L):
L = (2 ohms × π × [tex][0.65(10^{-3}m)]^{2}[/tex] / [tex][110(10^{-8} )][/tex] ohm-m)
Calculating the value:
L ≈ 1.05 meters
Therefore, a length of approximately 1.05 meters of Nichrome wire is needed to obtain a resistance of 2 ohms.
Learn more about resistance here:
https://brainly.com/question/29427458
#SPJ11
A cart with mass 200 g moving on a friction-less linear air track at an initial speed of 1.2 m/s undergoes an elastic collision with an initially stationary cart of unknown mass. After the collision, the first cart continues in its original direction at 1.00 m/s. What is the mass of the second cart?
The mass of the second cart is 0 kg, indicating that it is an object with negligible mass or a stationary object.
In an elastic collision, the total momentum before and after the collision remains constant. We can express this principle using the equation:
(m1 * v1) + (m2 * v2) = (m1 * u1) + (m2 * u2)
Where m1 and m2 are the masses of the first and second carts, v1 and v2 are their initial velocities, and u1 and u2 are their velocities after the collision.
In this scenario, the initial velocity of the first cart is given as 1.2 m/s, and its velocity after the collision is 1.00 m/s. The mass of the first cart is 200 g, which is equivalent to 0.2 kg.
We can rearrange the equation and solve for the mass of the second cart:
(m1 * v1) + (m2 * v2) = (m1 * u1) + (m2 * u2)
(0.2 * 1.2) + (m2 * 0) = (0.2 * 1.2) + (m2 * 1.00)
0.24 = 0.24 + m2
By subtracting 0.24 from both sides, we find that m2 = 0 kg.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
Determine the (magnitude) image magnification from placing an object 6.0 cm in front of a convex lens of focal length 9.0 cm. (Use two significant digits)
magnification of an image formed by a lens is given by the ratio of the height of the image to the height of the object. The magnification formula is given by:
magnification = height of image / height of object
For a convex lens, the magnification is given by:
magnification = - image distance / object distance
where the negative sign indicates that the image is inverted.
In this case, the object distance is 6.0 cm and the focal length is 9.0 cm. Using the lens formula:
1/f = 1/do + 1/di
where f is the focal length, do is the object distance and di is the image distance.
Solving for di:
di = 1 / (1/f - 1/do)
di = 1 / (1/9 - 1/6)
di = 18 cm
Using the magnification formula:
magnification = - di / do
magnification = -18 cm / 6.0 cm
magnification = -3.0
A power distribution substation uses transformers to step down AC voltages from 4.00 kV to 120 V for use in homes. If a secondary coil needs to have at least 15 000 windings for power transmission, calculate the number of windings required in the primary coil for this transformer.
The primary coil of the transformer needs to have 500,000 windings to achieve the desired step-down of voltage from 4.00 kV to 120 V. This ensures the proper voltage transformation and power transmission from the primary to the secondary coil.
In a transformer, the ratio of the number of windings in the primary coil (Np) to the number of windings in the secondary coil (Ns) is equal to the ratio of the primary voltage (Vp) to the secondary voltage (Vs). This can be expressed as Np/Ns = Vp/Vs.
Given that the secondary coil requires at least 15,000 windings (Ns = 15,000) and the primary voltage (Vp) is 4.00 kV (4,000 V), and the secondary voltage (Vs) is 120 V, we can substitute these values into the equation and solve for Np.
Using the formula Np/Ns = Vp/Vs, we have Np/15,000 = 4,000/120. By cross-multiplying and solving for Np, we find Np = (15,000 * 4,000) / 120. Calculating this expression yields Np = 500,000 windings.
Learn more about transformer here:
https://brainly.com/question/15200241
#SPJ11