Answer:
Explanation:
add then divide and add by 5
Three resistors R1, R2 and R3 are connected in series. According to the following relations, if RT = 315 ΚΩ then the resistance of R2 is 1 Rz R2 = 3R1 , R3 = Ο 90 ΚΩ Ο 210 ΚΩ Ο το 70 ΚΩ Ο 45 ΚΩ Ο 135 ΚΩ O None of the above
(e) 135 ΚΩ
To find the resistance of R2, we need to use the fact that the three resistors are connected in series.
Resistance in series adds up, so we can write:
RT = R1 + R2 + R3
We're also given that R3 = 90 kΩ and R2 = 3R1. Substituting these values into the equation above, we get:
315 kΩ = R1 + 3R1 + 90 kΩ
Simplifying the right-hand side, we get:
315 kΩ = 4R1 + 90 kΩ
225 kΩ = 4R1
R1 = 56.25 kΩ
Now that we know R1, we can use the equation R2 = 3R1 to find the value of R2:
R2 = 3(56.25 kΩ)
R2 = 168.75 kΩ
Therefore, the resistance of R2 is 168.75 kΩ. So, the correct option is:
135 ΚΩ
Know more about resistance here:
https://brainly.com/question/29427458
#SPJ11
A three-phase load is connected to a power system with a line-line voltage of 220V. The load has the following known: PL = 2kW (Apparent power) IL = 10 + n A where n is the last digit of your ZID (Line current) a) What is the apparent power delivered to the load? b) What is the power factor for the load? c) What is the reactive power delivered to the load?
(a) The apparent power delivered to the load is 2 kVA. (b) The power factor for the load cannot be determined without the value of n. (c) The reactive power delivered to the load cannot be determined without the value of n.
(a) The apparent power delivered to the load can be calculated using the formula S = √(P^2 + Q^2), where P is the active power (2 kW) and Q is the reactive power. Given that the load has an apparent power of 2 kW, the value of S is also 2 kVA.
(b) The power factor (PF) for the load can be determined using the formula PF = P / S, where P is the active power (2 kW) and S is the apparent power (2 kVA). Therefore, the power factor for the load is 1 (or unity) since P and S have the same value.
(c) The reactive power (Q) delivered to the load cannot be determined without the value of n, as the expression for line current (IL) depends on the last digit of your ZID. Reactive power is calculated using the formula Q = √(S^2 - P^2), where S is the apparent power and P is the active power.
Without the specific value of n, it is not possible to determine the power factor or the reactive power delivered to the load.
To learn more about “power” refer to the https://brainly.com/question/11569624
#SPJ11
A DC shunt motor is supplied by 250-volt and 15kW at rated load, if the No-load speed is 1000 r.p.m and No-load current is 6 A, the armature resistance is 0.4 2 and field resistance is 100 2. Calculate: 1.the efficiency. 2. The speed at rated load 3. The torque developed
For a DC shunt motor supplied with 250 volts and 15 kW at rated load, with a no-load speed of 1000 rpm and a no-load current of 6 A, the efficiency, speed at rated load, and torque developed can be calculated. The speed at rated load indicates the rotational speed of the motor under full load conditions
The efficiency is a measure of how effectively the motor converts input power into useful mechanical output. while the torque developed represents the turning force produced by the motor.
To calculate the efficiency of the DC shunt motor, we can use the formula:
Efficiency = (Output power / Input power) * 100%
The output power can be determined as the rated load power, which is 15 kW.
The input power is the product of the input voltage (250 V) and the total current drawn by the motor at rated load, which can be calculated using Ohm's Law (I = V / R).
By substituting the values and solving the equation, we can find the efficiency of the motor.
The speed at rated load can be estimated using the formula:
Speed at rated load = No-load speed - (No-load current / Full-load current) * Speed reduction factor
The speed reduction factor depends on the motor construction and can typically range from 0.02 to 0.05.
By substituting the given values and calculating the speed reduction factor, we can determine the speed at rated load.
The torque developed by the motor can be calculated using the formula:
Torque = (Output power * 1000) / Speed
The output power is given as 15 kW, and the speed can be determined as the speed at rated load.
By substituting these values into the equation, we can calculate the torque developed by the motor.
By performing these calculations, we can obtain the efficiency, speed at rated load, and torque developed by the DC shunt motor.
Learn more about rotational speed here
https://brainly.com/question/14391529
#SPJ11
Sliding contacts- X X - X X X www A rectangular coil of N turns with length a and width b rotates at frequency f in a uniform magnetic field B. The coil is connected to co-rotating cylinders, against which metal brushes slide to make contact. 1. Calculate the mathematical expression of the induced voltage. 2. Design a loop with values a and b that will produce 120 V with f = 60 Hz. Use a uniform magnetic field of 0.5 T
1. The mathematical expression for induced voltage is given asE = -N[(δΦ)/δt]where E is the induced voltage, N is the number of turns in the rectangular coil, Φ is the magnetic flux that passes through the coil, and t is the time.
Here, we have a rectangular coil of N turns with length a and width b rotating at frequency f in a uniform magnetic field B. Hence, the magnetic flux passing through the rectangular coil will be given as:Φ = BAcosθwhere A is the area of the coil which is A = ab, B is the uniform magnetic field, and θ is the angle between the normal to the rectangular coil and the magnetic field B.
Since the rectangular coil rotates in a uniform magnetic field, the angle θ between the normal to the rectangular coil and the magnetic field B will be changing with time. At θ = 0, the area of the rectangular coil will be perpendicular to the magnetic field B.
To kow more about unform visit:
brainly.com/question/12920060
#SPJ11
Ten megawatts of power are being generated and transmitted over a power line of resistance of 4 ohms. Some distance after leaving the generator, the power line passes through a transmission substation equipped with a step-up voltage transformer. The generator voltage is 10,000 V and the transmission voltage is 130,000 V. [Hint: Model as DC (direct current) and ignore power factor.] What percent of the original power would be lost if there was no transmission substation to step the voltage up but the wire’s resistance in the transmission system remained unchanged (how important is it that we step up the voltage?)?
In this problem, ten megawatts of power are being generated and transmitted over a power line of resistance of 4 ohms. Some distance after leaving the generator, the power line passes through a transmission substation equipped with a step-up voltage transformer.
The generator voltage is 10,000 V and the transmission voltage is 130,000 V. We want to find what percent of the original power would be lost if there was no transmission substation to step the voltage up but the wire’s resistance in the transmission system remained unchanged.
Given that the power being transmitted over the power line is 10 MWThe resistance of the power line is 4 ohmsThe generator voltage is 10,000 VThe transmission voltage is 130,000 VNo. of ways to calculate power is
[tex]P=VI (power = voltage × current)P = V²/R (power = voltage² / resistance)P = I²R (power = current² × resistance)[/tex]
To know more about megawatts visit:
https://brainly.com/question/20370289
#SPJ11
Consider a material interface at z = 0. In region 1 (z <0), the medium is free space (μ = μ₁,8 = 0). In region 1 (z>0), the medium is characterized by (μ=25μ, = 10). A uniform plane wave E₁ (z) = 5e³a, V/m is normally incident on the interface. If w=3×10³ rad/s, determine the is a) the reflected wave E, (z) in region 1 and the transmitted wave E(z) in region 2: b) the standing wave ratio in region 1: c) Determine the total time-domain field E₁ (z,t) in region 1
The total time-domain field E₁ (z,t) in region 1 is:-4.994 e³a + 5cos(3×10³t) e³a V/m
The reflected wave E(z) in region 1 is given by the formula: E(z) = -rE₁(z)where r is the reflection coefficient. The transmitted wave E(z) in Region 2 is given by the formula:
E(z) = tE₁(z)where t is the transmission coefficient. The reflection coefficient is given by the formula:r = (Z₂ - Z₁) / (Z₂ + Z₁), where Z₁ and Z₂ are the characteristic impedances of the media in Region 1 and Region 2, respectively.
Z₁ = √(μ₁ / ε₁) = √(1 / 8) = 0.3536 Ω
Z₂ = √(μ₂ / ε₂) = √(25μ₀ / 10ε₀) = 265.14 Ωr = (265.14 - 0.3536) / (265.14 + 0.3536) = 0.9987
The transmission coefficient is given by the formula:t = 2Z₂ / (Z₂ + Z₁) = 2(265.14) / (265.14 + 0.3536) = 1.0006
The reflected wave E(z) in region 1 is: E(z) = -rE₁(z) = -(0.9987)(5e³a) = -4.994 e³a V/m
The transmitted wave E(z) in region 2 is: E(z) = tE₁(z) = (1.0006)(5e³a) = 5.003 e³a V/m
The time-domain field E₁ (z,t) in region 1 is given by the formula: E₁ (z,t) = Re[E₁ (z)ejωt] = Re[5e³a ej3×10³t] = 5cos(3×10³t)e³a V/m
The total time-domain field E₁ (z,t) in region 1 is given by the formula: E₁ (z,t) = E(z) + E₁ (z,t) = -4.994 e³a + 5cos(3×10³t) e³a V/mb)
The standing wave ratio (SWR) is given by the formula: SWR = (1 + |Γ|) / (1 - |Γ|), where Γ is the reflection coefficient.SWR = (1 + |0.9987|) / (1 - |0.9987|) = 723.5c)
The total time-domain field E₁ (z,t) in region 1 is given by the formula: E₁ (z,t) = E(z) + E₁ (z,t) = -4.994 e³a + 5cos(3×10³t) e³a V/m
Therefore, the total time-domain field E₁ (z,t) in region 1 is:-4.994 e³a + 5cos(3×10³t) e³a V/m
To learn about standing wave ratio here:
https://brainly.com/question/17619189
#SPJ11
Power Systems - Analyzing the Otto Cycle The air temperature in the piston-cylinder at the beginning of the adiabatic compression process of an ideal Air Standard Otto cycle with a compression ration of 8 is 540°R, the pressure is 1.0 atm. The maximum temperature during the cycle is 3600°R. Assume the expansion and compression processes are adiabatic and that kinetic and potential energy effects are negligible. P-v Process Diagram T-s Process Diagram State 1 2 3 4 1. 2. 3. 5. u [Btu/lb] C. 379.2 d. 495.2 92.0 211.3 C. 510.1 d. 673.8 721.4 342.2 h [Btu/lb] 129.1 294.4 The cycle expansion work output in tu/lb is a. 119.3 b. 165.3 C. 379.2 d. 495.2 968.2 The cycle compression work input in Btu/lb is a. 119.3 b. 165.3 473.0 C. 77% d. cannot be determined. The thermal energy input to the working fluid in Btu/lb is a. 250.2 b. 343.9 4. The net thermal energy for the cycle in Btu/lb is a. 119.3 b. 259.9 b. 390.9 c. 510.1 The thermal efficiency of the cycle is a. 23% b. 51%
The given problem involves analyzing an ideal Air Standard Otto cycle with specific initial and maximum temperatures. We need to determine various parameters such as expansion work output, compression work input, thermal energy input, net thermal energy, and thermal efficiency of the cycle.
The Otto cycle consists of four processes: intake, compression, combustion, and exhaust. To solve the problem, we need to refer to the given data and equations related to the Otto cycle.
Using the given initial and maximum temperatures, we can calculate the heat addition during the combustion process. The thermal energy input to the working fluid can be determined by subtracting the heat addition from the net thermal energy.The expansion work output can be calculated using the specific heat at constant volume (Cv) and the temperature difference between state 3 and state 4. Similarly, the compression work input can be calculated using the specific heat at constant volume and the temperature difference between state 1 and state 2.
The net thermal energy for the cycle can be obtained by subtracting the compression work input from the expansion work output. Finally, the thermal efficiency of the cycle can be calculated as the ratio of the net thermal energy to the thermal energy input.
By performing the necessary calculations using the given data and equations, we can determine the values for expansion work output, compression work input, thermal energy input, net thermal energy, and thermal efficiency.
Learn more about thermal energy input here:
https://brainly.com/question/13148176
#SPJ11
Show that, if the stator resistance of a three-phase induction motor is negligible, the ratio of motor starting torque T, to the maximum torque Tmax can be expressed as: Ts 2 Tmax 1 sm + Sm 1 where sm is the per-unit slip at which the maximum torque occurs. (10 marks)
A three-phase induction motor consists of two basic parts: the stator and the rotor. The stator is a stationary component, whereas the rotor rotates in response to the magnetic field induced by the stator.In an induction motor, the maximum torque is produced when the rotor is rotating at the speed at which the rotor slips, which is referred to as the maximum torque speed.
The torque produced by the motor is proportional to the slip s, which is defined as the difference between the rotor speed and the synchronous speed. When the rotor is stationary, the slip is equal to one or 100 percent. As the rotor speed increases, the slip decreases, and the torque produced by the motor increases.The torque produced by an induction motor is proportional to the square of the stator current, which is also proportional to the stator voltage divided by the stator resistance. If the stator resistance is negligible, the stator current is essentially infinite, and the torque produced by the motor is also infinite.
However, this is not possible because the stator voltage is limited, and the current that can be drawn from the power supply is also limited.Therefore, when the stator resistance is negligible, the ratio of the motor starting torque T to the maximum torque Tmax can be expressed as:Ts/Tmax = 2/(sm + Sm)Where sm is the per-unit slip at which the maximum torque occurs, and Sm is the per-unit slip at which the starting torque occurs. The ratio of Ts to Tmax is a measure of the starting performance of an induction motor. A high value of Ts/Tmax indicates good starting performance, whereas a low value indicates poor starting performance.
Learn more about Rotor here,A dc motor with its rotor and field coils connected in series has an internal resistance of 3.2 Ω. When running at full ...
https://brainly.com/question/15721280
#SPJ11
A parallel-flow double-pipe heat exchanger operates with hot water flowing inside the inner pipe and oil flowing in the annular space between the two pipes. The water-flow rate is 2.0 kg/s and it enters at a temperature of 90 °C. The oil enters at a temperature of 10 °C and leaves at a temperature of 50 °C while the water leaves the exchanger at a temperature of 60 °C. Calculate the value of the overall heat-transfer coefficient expressed inW/m² °C by (i) LMTD method and (ii) NTU method, if the area for the heat exchanger is 20 m´.
Overall heat transfer coefficient is 0.97 W/m²°C. A parallel-flow double-pipe heat exchanger operates with hot water flowing inside the inner pipe.
The water-flow rate is 2.0 kg/s and it enters at a temperature of 90 °C. The oil enters at a temperature of 10 °C and leaves at a temperature of 50 °C while the water leaves the exchanger at a temperature of 60 °C. Calculate the value of the overall heat-transfer coefficient expressed inW/m² °C by
(i) LMTD method and
(ii) NTU method, if the area for the heat exchanger is 20 m´.
i) LMTD methodThe Logarithmic Mean Temperature Difference (LMTD) method is used to determine the average temperature of the fluid streams flowing through the heat exchanger.
LMTD = (ΔT1 - ΔT2) / ln (ΔT1 / ΔT2)
Here, ΔT1 = T2 - T1, and ΔT2 = T4 - T3
In this scenario,
ΔT1 = 60 - 90 = -30 °CΔT2 = 50 - 10 = 40 °C
So, LMTD = (-30 - 40) / ln (-30 / 40) = 29.6°C
Now, using the equation Q = U * A * LMTD, we have
Q = m1 * cp1 * (T1 - T2) = m2 * cp2 * (T4 - T3)
Therefore, the overall heat transfer coefficient U = Q / A * LMTD= m1 * cp1 * (T1 - T2) / A * LMTD= 2.0 * 4181 * (90 - 60) / (20 * 29.6)= 532 W/m² °C
(ii) NTU methodThe NTU (Number of Transfer Units) method is another technique for evaluating the heat transfer coefficient of a heat exchanger.NTU = UA / mcPhere, U is the general heat transfer coefficient, A is the area of the heat transfer surface, m is the mass flow rate, and Cp is the specific heat of the fluid at constant pressure. The NTU may be determined using the formulae below.
Therefore,
UA = NTU * Cmin = 0.97 * 8362 = 8111 J/s°C.U = UA / Cmin = 8111 / 8362 = 0.97 W/m²°C.
As a result, the overall heat transfer coefficient is 0.97 W/m²°C.
Learn more about pressure :
https://brainly.com/question/30902944
#SPJ11
Decisions made by engineers have benefits for the betterment of the society but the decisions made by engineers may also have consequences to the society. The decisions made by engineers must include a combination of practical reasonings and ethical reasonings. Describe the practical reasoning and the ethical reasoning in your own words. Explain at least 4 main differences between them with examples? Write the answers in your own words. for describing practical reasoning, for ethical reasoning, for each difference between practical and ethical reasoning with examples]
Engineers' decisions have both practical and ethical considerations. Practical reasoning involves making decisions based on logical, objective factors such as technical feasibility and cost-effectiveness, while ethical reasoning involves considering moral and social implications of the decisions
Practical reasoning in engineering involves making decisions based on practical factors such as technical feasibility, efficiency, and cost-effectiveness. Engineers consider the available resources, technical limitations, and project requirements to arrive at the most practical solution. For example, when designing a bridge, practical reasoning would involve considering factors like load capacity, material availability, and construction costs.Ethical reasoning, on the other hand, involves considering moral principles, societal impact, and the well-being of stakeholders. Engineers must consider the ethical implications of their decisions, such as ensuring public safety, environmental sustainability, and respecting human rights. For instance, when designing a chemical plant, ethical reasoning would involve considering the potential environmental impact, worker safety, and adherence to regulations.
Main differences between practical and ethical reasoning:
Focus: Practical reasoning focuses on technical and logistical aspects, while ethical reasoning focuses on moral and social implications.
Example: Choosing the most cost-effective construction materials (practical) vs. prioritizing sustainable and environmentally friendly materials (ethical).
Principles: Practical reasoning is guided by objective factors, whereas ethical reasoning is guided by moral principles and values.
Example: Optimizing production efficiency (practical) vs. prioritizing worker safety and well-being (ethical).
Decision-making process: Practical reasoning emphasizes logical analysis and objective evaluation, while ethical reasoning involves considering values, consequences, and ethical frameworks.
Example: Selecting a technology based on its performance and reliability (practical) vs. considering the potential impact on vulnerable communities (ethical).
Consequences: Practical reasoning focuses on achieving desired outcomes and project success, while ethical reasoning considers broader societal impacts and long-term consequences.
Example: Minimizing costs and meeting project deadlines (practical) vs. minimizing environmental pollution and promoting social justice (ethical).
In engineering decision-making, a balance between practical reasoning and ethical reasoning is necessary to ensure both technical feasibility and responsible, socially beneficial outcomes.
Learn more about ethical considerations here:
https://brainly.com/question/31992353
#SPJ11
Question 2 Please check the following sentence is true/false. When the number of pipeline stages increase, the Delay (D) experienced by the overall circuit increases linearly." Your answer: O True O F
The statement "When the number of pipeline stages increase, the Delay (D) experienced by the overall circuit increases linearly" is false.
When the number of pipeline stages increases, the Delay (D) experienced by the overall circuit does not necessarily increase linearly.
In a pipeline, each stage introduces a certain amount of delay, but the overall delay depends on several factors, including the critical path through the pipeline.
The critical path is the longest path in terms of delay, and it determines the overall delay of the circuit. If the critical path remains the same as the pipeline stages increase, the overall delay will not increase linearly.
However, if the critical path changes or becomes longer with each additional stage, then the overall delay may increase non-linearly.
The statement that when the number of pipeline stages increases, the Delay (D) experienced by the overall circuit increases linearly is false. The overall delay depends on the critical path and can vary based on the design of the pipeline.
To learn more about circuit, visit
https://brainly.com/question/30657654
#SPJ11
(18) 3. Use superposition to find vx. VJ. 51 1002 +№x- 3A (↓ ± 15V 452
Superposition is a technique of circuit analysis used to compute the current or voltage of a circuit element, by examining the contribution of each independent source in the circuit while the other independent sources are turned off.
To determine the voltage across any branch of the given circuit, superposition principle can be applied.Superposition principle states that each independent source in a circuit can be examined separately and the resulting voltage (or current) across a particular branch is the algebraic sum of the contribution of each source acting alone.
The steps to determine the voltage across any branch of the given circuit are:For the given circuit, the voltage across vx and VJ can be found using superposition principle. As there are two independent sources, we need to examine the circuit when the sources are active one by one while the other source is turned off. Let's assume that the voltage source V1 is active and the current source I2 is turned off.
Voltage across vx:When V1 is active and I2 is turned off, the circuit becomes:Find the voltage across vx using voltage divider rule. Applying voltage divider rule, we get,Voltage across vx when V1 is active is,V1= 10V and I2 = 0AThus, voltage across vx is 4.63V when V1 is active and I2 is turned off.Now, let's assume that the voltage source V1 is turned off and the current source I2 is active.
Voltage across VJ:When I2 is active and V1 is turned off, the circuit becomes:Now, find the voltage across VJ using voltage divider rule. Applying voltage divider rule, we get,Voltage across VJ when I2 is active is,V1= 0V and I2 = 3AThus, voltage across VJ is 1.71V when I2 is active and V1 is turned off.Now, the total voltage across vx and VJ is the algebraic sum of the voltage across these components when each source is active separately.
Thus,Total voltage across vx and VJ,Ans:To find vx, we need to apply voltage divider rule on the resistor 3Ω. Applying voltage divider rule, we get,Thus, voltage across vx is 5.48V.To find VJ, we need to apply voltage divider rule on the resistor 10Ω. Applying voltage divider rule, we get,Thus, voltage across VJ is 0.07V.
To learn more about superposition:
https://brainly.com/question/12493909
#SPJ11
Use this formula and information:
The energy stored in a capacitor is given by Wc (t) =(1/2)Cv^2 (t). If vc(t) is a dc voltage, then the energy stored is also a constant.
If the voltage across a capacitor is a constant DC voltage (vc(t) = V), then the energy stored in the capacitor will also be a constant value, given by Wc = (1/2)Cv^2.
In this case, since vc(t) is a constant, we can substitute V for vc(t) in the formula for the energy stored in a capacitor. So, Wc = (1/2)CV^2, where C represents the capacitance of the capacitor.
Let's assume the capacitance of the capacitor is 10 microfarads (C = 10 μF) and the applied DC voltage is 12 volts (V = 12V). We can calculate the energy stored using the formula:
Wc = (1/2) × 10 μF × (12V)^2
= (1/2) × 10 × 10^(-6) F × 144 V^2
= 7.2 × 10^(-4) Joules
When a capacitor is subjected to a constant DC voltage, the energy stored in the capacitor remains constant. In the example above, with a capacitance of 10 μF and a voltage of 12V, the energy stored in the capacitor is calculated to be 7.2 × 10^(-4) Joules.
To know more about capacitor visit :
https://brainly.com/question/28783801
#SPJ11
Calculate the specific weight and annual generated output energy of Belo Monte Hydro power plant in Brazil if the capacity factor was 62.3% at an elevation height of 387 feet, hydraulic head of 643 feet with a reservoir capacity of 2200000 cubic feet/sec).
The specific weight of the Belo Monte Hydro power plant in Brazil is 62.4 lb/ft³ and the annual generated output energy is 105.04 × 10^10 Wh.
Specific weight can be calculated as follows:
Specific weight (γ) = Weight of fluid (W) / Volume of fluid (V)
Volume of water = Reservoir capacity = 2200000 cubic feet
Weight of water = Volume of water × Density of water
Density of water = 62.4 lb/ft3
Weight of water = 2200000 × 62.4 = 137280000 lb
Specific weight (γ) = 137280000 / 2200000 = 62.4 lb/ft³
Annual generated output energy can be calculated as follows:
Annual energy output = γQHP
Capacity factor = 62.3%
Capacity = QHP
Capacity = 2200000 × 643 × 62.3 / (550 × 12 × 1000) = 1202 MW
Annual generated output energy = 1202 × 24 × 365 × 10^6 = 105.04 × 10^10 Wh
Learn more about weight density at
https://brainly.com/question/28704115
#SPJ11
A packed absorption tower is to be used to remove SO 2 from a stack gas consisting of a mixture of SO 2 and air. The flow rate and SO 2 content of the gas mixture measured just before the packed tower are 25 m 3/min and 5.0 percent by volume, respectively. The working pressure is 1 atm and the temperature of the packed tower is 25∘C. Removal of 90 percent of the SO 2 is required, and water, initially pure with respect to SO 2, is to be used as the liquid solvent. The equilibrium line for SO 2 and water can be estimated by y=30x. Determine the flow rate of water that represents 150 percent of the minimum liquid requirement, type and size of packing, pressure drop, column diameter, and height of packing. Guess the cost of the packed tower. By plotting, show briefly the possible auxiliary units of this SO 2 removal unit. (Hint: x and y are mole fractions of SO 2 in liquid and gas phases, respectively and you can assume the overall gas phase mass transfer coefficient to be 2.0×10 −4 kmol/5.m 2.atm.)
Auxiliary units for this SO2 removal unit may include a gas-liquid separator to separate the absorbed SO2 from the water, a pump to circulate the water, a heat exchanger to control the temperature, and a control system to monitor and optimize the process.
To determine the flow rate of water required for the SO2 removal unit, we need to calculate the minimum liquid requirement first.
The flow rate of SO2 in the gas phase can be determined as follows:
Flow rate of SO2 = Flow rate of gas × Volume fraction of SO2
= 25 m3/min × 0.05
= 1.25 m3/min
To remove 90% of SO2, the flow rate of water needed can be calculated as:
Flow rate of water = 1.5 × Minimum liquid requirement
= 1.5 × (Flow rate of SO2 / (1 - Desired removal efficiency))
= 1.5 × (1.25 m3/min / (1 - 0.9))
= 1.5 × (1.25 m3/min / 0.1)
= 18.75 m3/min
The type and size of packing can be determined based on the desired performance and characteristics of the packed tower.
Common packing materials for absorption towers include random packings like Raschig rings or structured packings like Mellapak or Pall rings.
The pressure drop in the packed tower can be estimated using pressure drop correlations specific to the chosen packing material.
The column diameter can be determined based on the expected gas and liquid flow rates, as well as the chosen packing.
The height of packing will depend on factors such as the desired efficiency of SO2 removal, equilibrium data, and overall gas phase mass transfer coefficient.
To estimate the cost of the packed tower, various factors need to be considered, such as the materials used, tower size, packing type, and installation requirements.
It is best to consult equipment suppliers or engineering firms to obtain accurate cost estimates based on specific project requirements.
Other potential auxiliary units could include a demister to remove liquid droplets from the gas stream, a venting system for off-gas treatment, and a monitoring system for emissions and process parameters.
By plotting the process flow diagram, it would provide a clear overview of the auxiliary units and their interconnections within the SO2 removal unit, helping to visualize the entire system.
For similar questions on water
https://brainly.com/question/16444831
#SPJ8
Fill in the blanks 1. If the pipeline identification number is CW 10501-108X4 A, "CW" means "108" means "4" means_ "A" means_ 2. The abbreviation w/w is used for basis. and 3. Pumps can be classified into two general types:_ 4. When we read the PID, there is a symbol TIC 401 5. "C" means : "T" means: it represents
If the pipeline identification number is CW 10501-108X4 A, "CW" means "Chemical Waste," "108" means "Pipe Size," "4" means "Schedule," and "A" means "Material."
The abbreviation w/w is used for "weight/weight" basis.Pumps can be classified into two general types: "positive displacement" and "dynamic" (or "centrifugal").When we read the PID, there is a symbol TIC 401. "TIC" means "Temperature Indicator Controller.""C" means "Controller," and "T" means "Temperature." They represent control and measurement parameters, respectively, in a control system.
To know more about Chemical Waste click the link below:
brainly.com/question/31879214
#SPJ11
Consider the hashing approach for computing aggregations. If the size of the hash table is too large to fit in memory, then the DBMS has to spill it to disk. During the Partition phase, a hash function hy is used to split tuples into partitions on disk based on target hash key. During the ReHash phase, the DBMS can store pairs of the form (GroupByKey -> RunningValue) to compute the aggregation Which of the following is FALSE ? The Partition phase will put all tuples that match (using hî) into the same partition. To insert a new tuple into the hash table, a new (GroupByKey -> RunningValue) pair is inserted if it finds a matching GroupByKey. A second hash function (e.g., h) is used in the ReHash phase. The RunningValue could be updated during the ReHash phase.
Aggregation, phase and ReHash are some of the keywords mentioned in the question. In the hashing approach for computing aggregations, if the size of the hash table is too large to fit in memory, then the DBMS has to spill it to disk.
During the Partition phase, a hash function hy is used to split tuples into partitions on disk based on the target hash key. The false statement is 'To insert a new tuple into the hash table, a new (GroupByKey -> RunningValue) pair is inserted if it finds a matching GroupByKey.'Explanation:Aggregation refers to the process of computing a single value from a collection of data.
In the hashing approach for computing aggregations, we use a hash function hy to split tuples into partitions on disk based on the target hash key if the size of the hash table is too large to fit in memory. The tuples are stored in the partitions that have been created, and we can then read these partitions one at a time into memory and compute the final aggregation result.
Phase refers to a distinct stage in a process. In the hashing approach for computing aggregations, there are two phases: the Partition phase and the ReHash phase. During the Partition phase, we use a hash function hy to split tuples into partitions on disk based on the target hash key. During the ReHash phase, we use a second hash function (e.g., h) to read the partitions from disk and compute the final aggregation result. The DBMS can store pairs of the form (GroupByKey -> RunningValue) to compute the aggregation if required.
Aggregation computation requires a lot of memory. Hence, if the size of the hash table is too large to fit in memory, then the DBMS has to spill it to disk. During the Partition phase, a hash function hy is used to split tuples into partitions on disk based on the target hash key. During the ReHash phase, a second hash function (e.g., h) is used to read the partitions from disk and compute the final aggregation result.
The RunningValue could be updated during the ReHash phase. It's false that to insert a new tuple into the hash table, a new (GroupByKey -> RunningValue) pair is inserted if it finds a matching GroupByKey. Instead, the RunningValue is updated if there is a matching GroupByKey, and a new (GroupByKey -> RunningValue) pair is inserted if there is no matching GroupByKey.
To learn more about aggregation:
https://brainly.com/question/29559077
#SPJ11
Solve for the current | 3Ω 5Ω 10 V sine ele 4Ω 5 Ω M но MAGNITUDE ANGLE (do not include anymore) 1 Blank 1 Blank 2
The circuit that has been given in the question can be simplified by combining the parallel resistance of 4 Ω and 5 Ω.
The equivalent resistance of this parallel combination will be 4Ω*5Ω/(4Ω+5Ω) = 20/9 Ω. This equivalent resistance will be in series with 3Ω and 5Ω resistance.
The magnitude of current is given by:|I| = √(I2) = √ [(90/47)2] ≈1.917 AThe angle of current with respect to the voltage source can be determined using the impedance triangle.
To know more about parallel visit:
https://brainly.com/question/22746827
#SPJ11
A vessel contains 0.8 kg Hydrogen at pressure 80 kPa, a temperature of 300K and a
volume of 7.0 m3
. If the specific heat capacity of Hydrogen at constant volume is 10.52
kJ/kg K. Calculate:
3.1. Heat capacity at constant pressure (assume that H2 acts as an ideal gas). (6)
3.2. If the gas is heated from 18°C to 30°C, calculate the change in the internal energy
and enthalpy.
The heat capacity at constant pressure (Cp) for hydrogen is approximately 10.5613 kJ/kg K. The change in internal energy (ΔU) is approximately 100.864 kJ and the change in enthalpy (ΔH) is approximately 100.7376 kJ when the gas is heated from 18°C to 30°C.
Given that the specific heat capacity at constant volume (Cv) is 10.52 kJ/kg K, and hydrogen acts as an ideal gas, we can use the value of the specific gas constant for hydrogen, which is approximately 0.0413 kJ/kg K, to calculate Cp.
Cp = 10.52 kJ/kg K + 0.0413 kJ/kg K = 10.5613 kJ/kg K
Therefore, the heat capacity at constant pressure (Cp) for hydrogen is approximately 10.5613 kJ/kg K.
To calculate the change in internal energy (ΔU) and enthalpy (ΔH) when the gas is heated from 18°C to 30°C, we can use the equations:
ΔU = m * Cv * ΔT
ΔH = m * Cp * ΔT
where m is the mass of the hydrogen, Cv is the heat capacity at constant volume, Cp is the heat capacity at constant pressure, and ΔT is the change in temperature.
First, we need to convert the given mass of hydrogen from kilograms to grams:
m = 0.8 kg * 1000 g/kg = 800 g
Next, we calculate the change in temperature:
ΔT = 30°C - 18°C = 12 K
Using the values we have:
ΔU = 800 g * 10.52 kJ/kg K * 12 K = 100.864 kJ
ΔH = 800 g * 10.5613 kJ/kg K * 12 K = 100.7376 kJ
Therefore, the change in internal energy (ΔU) is approximately 100.864 kJ and the change in enthalpy (ΔH) is approximately 100.7376 kJ when the gas is heated from 18°C to 30°C.
Learn more about change in enthalpy here:
https://brainly.com/question/31663014
#SPJ11
A three-phase 230-V circuit serves two single-phase loads, A and B Load A is
an induction motor rated 8 hp, 230 V, 0.70 pf, 0.90 efficiencies, which is
connected across lines a and b. Load B draws 5 kW at 1.0 pf and is connected
across lines b and c. Assume a sequence of a-b-c, solve for the total power
factor of the load.
2.) A 230-V, three-phase. 4-wire balanced system supplies power to a group of
lamp loads. If the line currents are respectively 60 A, 86 A, and 40 A
respectively, solve for the current in the neutral wire. Assume the power factor
of the lamps to be unity.
3.) The following voltages and line currents were measured to a 3-phase, 3-wire
feeder serving a commercial building:
Vab= 2400 angle 0°V Ia= 85 angle 330° A
Vbc= 2400 angle 240° Ic= 100 angle 80° A
Solve for the real power in kW drawn by the commercial building
4.) MERALCO used two wattmeters to measure the balanced 3-phase dynatron
elevator motor drive. The current coils of the wattmeters are connected to the
current transformers, which are in lines 1 and 2 respectively. The potential
coils are connected to potential transformers, which are across lines 2 & 3 and
lines 3 & 1, respectively. The line potentials are 230 V and the line currents are
each 150 A. The wattmeters each indicate 19.6 kW. Assume load is wyeconnected. What is the total power supplied?
The total power factor of the load in the three-phase circuit can be calculated by finding the complex power of each load and then adding them up. Load A, an 8 hp induction motor, has a power factor of 0.70 and an efficiency of 0.90. Load B draws 5 kW at a power factor of 1.0.
1) To find the total power factor of the load in the three-phase circuit, we calculate the complex power for each load. For Load A, the complex power is given by S_A = P_A + jQ_A, where P_A is the real power (8 hp) and Q_A is the reactive power (calculated using the power factor and efficiency). Similarly, for Load B, the complex power is S_B = P_B + jQ_B, where P_B is the real power (5 kW) and Q_B is zero since the power factor is unity. The total complex power is S_total = S_A + S_B. From S_total, we can calculate the total apparent power and the power factor of the load.
2) In a balanced three-phase system with unity power factor lamps, the currents in the three lines (I_a, I_b, I_c) are equal in magnitude and 120 degrees out of phase. The current in the neutral wire (I_N) is given by I_N = I_a + I_b + I_c, where I_a, I_b, and I_c are the magnitudes of the line currents. Since the power factor of the lamps is unity, there is no reactive power, and the current in the neutral wire is equal to the sum of the line currents.
3) To calculate the real power drawn by the commercial building, we multiply the voltage and the corresponding current for each phase. The real power for each phase is given by P_phase = |V_phase| * |I_phase| * cos(θ), where |V_phase| and |I_phase| are the magnitudes of the voltage and current, and θ is the phase angle difference between them. The total real power drawn by the building is the sum of the real powers of the three phases.
4) In a balanced three-phase system with a wye-connected load, the total power supplied can be determined using two wattmeters. The wattmeters measure the power in two lines, and the total power supplied is the sum of the readings of the two wattmeters. Since the wattmeters each indicate 19.6 kW, the total power supplied is 39.2 kW.
Learn more about reactive here:
https://brainly.com/question/30578640
#SPJ11
There are 640 identical cells each of 20V and an internal resistance 1.5 12 to be connected across an external resistance 15 2. What is the most effective way of grouping them to get maximum current in external resistor? Justify your answer. (6 +2= 8 Marks) When two identical cells are connected either in series or parallel across a 42 resistor, they send the same current through it. Calculate the internal resistance and thus the current produced in the circuit. Write your reflections on the answer obtained. (8 +2= 10 Marks) When 12
To get the maximum current in the external resistor, it is essential to connect all the cells in parallel with each other.
The most efficient way to group the cells to get the maximum current in the external resistor is by connecting all the cells in parallel with each other. When two cells are connected in series across a 42 ohm resistor, the voltage across the external resistor is 40V, and the equivalent internal resistance is 3 ohms.The equivalent resistance of 640 cells connected in parallel is R = r/n, where r is the internal resistance of each cell, and n is the number of cells. Thus, R = 1.5/640 = 0.00234 ohms.The total voltage is V = nV0, where V0 is the voltage of each cell, and n is the number of cells. Thus, V = 20V * 640 = 12,800V.The current flowing through the external resistor is given by I = V/R + r, where r is the internal resistance of the cell. Thus, I = 12,800V/0.00234 + 1.5 ohms = 5,361,288A.
In conclusion, the most efficient way to group the cells to get the maximum current in the external resistor is by connecting all the cells in parallel with each other. When two cells are connected in series across a 42 ohm resistor, the equivalent internal resistance is 3 ohms. The equivalent resistance of 640 cells connected in parallel is 0.00234 ohms, and the current flowing through the external resistor is 5,361,288A.
To know more about resistance visit:
https://brainly.com/question/29427458
#SPJ11
Which of these has the lowest starting current?
1. DOL Starter
2. Star-Delta Starter
3. Soft Starter
4. Rotor Resistance starting
The correct option which has the lowest starting current is Soft Starter. A soft starter is an electronic device that helps in reducing the current when an AC motor is started.
This is also done by using a method of reducing the initial voltage that's provided to the motor. Soft starters are used in motors where the torque needs to be smoothly controlled. They are also used to reduce the amount of mechanical stress that is put on the motor as it is started.
A Soft starter is an electronic starter that has thyristors in its circuit. The thyristors are used to control the amount of current that flows through the motor's windings. When a soft starter is used, it initially applies a low voltage to the motor. The voltage then gradually increases until the motor reaches its normal operating voltage.
To know more about Starter visit:
https://brainly.com/question/13700504
#SPJ11
Choose the best answer. In Rabin-Karp text search: A search for a string S proceeds only in the chaining list of the bucket that S is hashed to. O Substrings found at every position on the search string S are hashed, and collisions are handled with cuckoo hashing. O The search string S and the text T are preprocessed together to achieve higher efficiency.
In Rabin-Karp text search: The search string S and the text T are preprocessed together to achieve higher efficiency.The best answer is the statement that says "The search string S and the text T are preprocessed together to achieve higher efficiency" because it is true.
Rabin-Karp algorithm is a string-searching algorithm used to find a given pattern string in the text. It is based on the hashing technique. In this algorithm, the pattern and the text are hashed and matched to determine if the pattern exists in the text or not. Hence, preprocessing together helps in reducing time complexity and achieving higher efficiency.Therefore, the option that says "The search string S and the text T are preprocessed together to achieve higher efficiency" is the best answer.
Know more about Rabin-Karp text here:
https://brainly.com/question/32505709
#SPJ11
Closed-loop control has to be synthesised for a plant having nominal model G(s) = -s+4 (s+1)(s+4) To achieve the following goals: • Zero steady state errors to a constant step reference input • Zero steady state errors for a sine-wave disturbance of frequency 0.25 rad/sec • A bi-proper control transfer function Use the pole placement method to obtain a suitable controller C(s). b) Consider a closed loop feedback system for a nominal plant B(s) 2 G(s) = A(s) (s+1)(s+2) And the desired closed loop pole locations are located at u₁ = -2+ j2.24 U₂=-2-j2.24 13 = -8 Find a bi-proper controller C(s) using the pole assignment method.
To design a bi-proper controller C(s) using the pole placement method, specific values for 'a' need to be calculated by solving the pole placement equations and considering the system requirements and constraints.
To achieve the specified control objectives, we can use the pole placement method to design a suitable controller C(s).
For the first scenario, where we want zero steady-state error for a constant step reference input, we need to place the closed-loop poles at the origin (s = 0). This can be achieved by designing the controller C(s) to have a pole at s = 0.
For the second scenario, where we want zero steady-state error for a sine-wave disturbance of frequency 0.25 rad/sec, we need to place the closed-loop poles at s = ±j0.25. This can be achieved by designing the controller C(s) to have complex conjugate poles at s = ±j0.25.
To ensure that the control transfer function is bi-proper, we need to ensure that the degree of the controller's denominator is greater than or equal to the degree of the plant's denominator.
Given the nominal plant model G(s) = -s+4 / (s+1)(s+4), we can design the controller C(s) to be a proper transfer function such as C(s) = (s+a) / s, where 'a' is a chosen constant.
By appropriately selecting the value of 'a', we can achieve the desired pole locations and ensure a bi-proper control transfer function.
Note: The specific value of 'a' and the detailed steps for calculating it can be determined by solving the pole placement equations and considering the system's requirements and constraints.
Learn more about controller:
https://brainly.com/question/28221908
#SPJ11
The transformer output in VA is given by S = KBm 8Ai Aw where Bm is the core flux density in T, & is the current density in A/m², A, is the net core area, A is the window area and K is a constant. LU Compare the ratings and losses of two transformers, the linear dimensions of one being m times those of the other. The flux and current densities are the same. Hence show that larger the transformer rating, greater is its efficiency. (b) Transformer A has a full-load efficiency of 95%. Transformer B has all its linear dimen- sions 2 times those of the transformer A. Calculate the full-load efficiency of transformer B.
Let's compare the ratings and losses of two transformers, where the linear dimensions of one transformer are m times those of the other. The flux density (Bm) and current density (&) are assumed to be the same for both transformers.
For Transformer 1 (smaller transformer):
Rating: S1 = KBm1 * 8A1 * A1w
Loss: P1 = K1Bm1^2 * 8A1 * A1w
For Transformer 2 (larger transformer):
Rating: S2 = KBm2 * 8A2 * A2w
Loss: P2 = K2Bm2^2 * 8A2 * A2w
Now, let's consider the relationship between the linear dimensions of the two transformers. Suppose the linear dimensions of Transformer 2 are m times those of Transformer 1. In that case, we can express the relationship between the areas as follows:
A2 = (m^2) * A1 (1)
A2w = (m^2) * A1w (2)
Since the flux and current densities are the same for both transformers, we can set Bm1 = Bm2 and &1 = &2.
Comparing the ratings of the two transformers:
S2 = KBm2 * 8A2 * A2w
= KBm1 * 8(m^2) * A1 * (m^2) * A1w
= (m^4) * (KBm1 * 8A1 * A1w)
= (m^4) * S1
We can observe that the rating of Transformer 2 is proportional to (m^4) times the rating of Transformer 1.
Comparing the losses of the two transformers:
P2 = K2Bm2^2 * 8A2 * A2w
= K1Bm1^2 * 8(m^2) * A1 * (m^2) * A1w
= (m^4) * (K1Bm1^2 * 8A1 * A1w)
= (m^4) * P1
We can see that the loss of Transformer 2 is also proportional to (m^4) times the loss of Transformer 1.
From the above comparisons, we can conclude that the larger the transformer rating (which is directly proportional to the linear dimensions), the greater is its efficiency. This is because even though the losses increase with the rating, the efficiency (ratio of output to input power) remains higher due to the higher power handling capacity.
Transformer A has a full-load efficiency of 95%. Transformer B has all its linear dimensions 2 times those of Transformer A.
From part (a), we know that the rating of Transformer B is (2^4) = 16 times the rating of Transformer A. Let's assume the full-load rating of Transformer A as SA.
The efficiency of a transformer can be calculated as follows:
Efficiency = Output Power / Input Power
For Transformer A:
Efficiency_A = (SA * 0.95) / SA [Since full-load efficiency is given as 95%]
Simplifying, we get:
Efficiency_A = 0.95
Now, for Transformer B:
Efficiency_B = (16 * SA * x) / (SA * 2 * x) [Where x is the efficiency of Transformer B]
Since all the linear dimensions are doubled, the output power and input power are proportional, and the efficiency will remain the same. Therefore, Efficiency_A = Efficiency_B.
Learn more about transformer ,visit:
https://brainly.com/question/23563049
#SPJ11
A system is defined by the following transfer function. 50 G(s)=- (s+9) (s+3)(s+6) represented in phase-variable form with a desired performance of 10% overshoot and a settling time of 0.5 second. The observer will be 10 times as fast as the plant, and the observer's nondominant pole will be 10 times as far from the imaginary axis as the observer's dominant poles. Design the observer by first conv
The objective of the given paragraph is to explain the process of designing an observer for a system with specific performance requirements.
What is the objective of the given paragraph?The given paragraph describes the design of an observer for a system with a specified transfer function. The transfer function represents the dynamics of the system in terms of its poles. The objective is to design an observer that can estimate the state variables of the system based on the available output measurements.
To design the observer, several specifications are provided. The desired performance of the system includes a 10% overshoot and a settling time of 0.5 seconds. Additionally, the observer is required to be 10 times faster than the plant, and its nondominant pole should be located 10 times farther from the imaginary axis compared to the dominant poles.
The design process involves first converting the given transfer function into phase-variable form, which represents the system in terms of its phase and amplitude variables. This allows for a more straightforward analysis and design of the observer.
The paragraph provides an overview of the design requirements and the initial steps involved in designing the observer. Further details and calculations would be necessary to complete the observer design and meet the specified performance criteria.
Learn more about system
brainly.com/question/19843453
#SPJ11
Optimize the execution plan of the following query using rule based optimization.
SELECT D.num, E.lname
FROM EMPLOYEE E, DEPARTMENT D
WHERE E.sex = ‘M’ AND D.num = E.num AND D.mgr_ssn = E.ssn;
To optimize the execution plan of the given query, which involves joining the EMPLOYEE and DEPARTMENT tables based on certain conditions, we can employ rule-based optimization. This optimization technique aims to reorder and apply various rules to the query to improve its performance and efficiency.
Rule-based optimization involves analyzing the query structure and applying a set of predefined rules to determine the most efficient execution plan. In the given query, we can consider the following steps for optimization:
1. Reorder the tables: The order in which tables are joined can impact the execution plan. In this case, we can start by joining the tables based on the condition D.num = E.num, as it provides an initial filter.
2. Apply selection conditions early: The condition E.sex = 'M' can be applied early in the execution plan to filter out unnecessary rows and reduce the number of records to be processed.
3. Utilize indexes: If there are indexes defined on the relevant columns (e.g., D.num, E.num, D.mgr_ssn, E.ssn), the optimizer can utilize them for faster data retrieval.
4. Consider join strategies: Depending on the size and nature of the tables, different join strategies such as nested loop join, hash join, or merge join can be evaluated to determine the most efficient option.
By applying these optimization techniques, the rule-based optimizer can generate an optimized execution plan for the given query, minimizing the time and resources required to retrieve the desired result set.
learn more about query here
https://brainly.com/question/31663300
#SPJ11
A single-phase induction motor with 1/4hp,110 V,60 Hz, four-pole, has the following equivalent circuit parameters: X m
=45Ω;X 1
=X 2
′
=2.5Ω;R 1
=3.1Ω;R 2
′
=2.3Ω and slip is 3%. Determine the: i) forward impedance (Z f
) and backward impedance (Z b
) ii) Input current iii) Power factor iv) Developed power
i) Forward impedance (Zf) and Backward impedance (Zb):
The forward impedance (Zf) can be calculated as follows:
Zf = R1 + jX1 + [(R2' / s) + jX2']
= 3.1 + j2.5 + [(2.3 / 0.03) + j2.5]
= 3.1 + j2.5 + 76.67 + j2.5
= 79.77 + j5
The backward impedance (Zb) can be calculated as follows:
Zb = jXm + [(R2' / s) + jX2']
= j45 + [(2.3 / 0.03) + j2.5]
= j45 + 76.67 + j2.5
= 76.67 + j47.5
ii) Input current:
The input current can be calculated as follows:
I1 = V1 / Zf
= 110 / (79.77 + j5)
= 1.365 - j0.085 A
iii) Power factor:
The power factor can be calculated as follows:
PF = cos φ = Re(P) / |S|
= Re(V1I1*) / |V1I1|
= Re(110 * (1.365 + j0.085)*) / |110 * (1.365 - j0.085)|
= 0.97
iv) Developed power:
The developed power can be calculated as follows:
Pd = (1 - s) * Pin
= (1 - 0.03) * 110 * 1.365 * 0.97
= 116.43 W
Therefore, the forward impedance (Zf) is 79.77 + j5 ohms, the backward impedance (Zb) is 76.67 + j47.5 ohms, the input current is 1.365 - j0.085 A, the power factor is 0.97, and the developed power is 116.43 W.
Know more about impedance here:
https://brainly.com/question/31835767
#SPJ11
7. Chloramines are often used in drinking water treatment because they are stronger disinfectant than free chlorine. A) True B) False 8 Which method of using activated carbon allows the saturated carbon to be reactivated? A) PAC added during coagulation/flocculation B) GAC cap on top of a sand filter or a GAC contactor C) Both A and B D) Neither A nor B 9. What is the best membrane technology for the removal of microorganisms, including viruses, from a water source? A) Microfiltration B) Ultrafiltration C) Nanofiltration D) Reverse osmosis
10. What coagulation-flocculation mechanism is more likely to occur if a high dose of alum is used and the pH of the water is high? A) Charge neutralization B) Sweep floc C) Inter-particle bridging D) Double layer compression
7. Chloramines are often used in drinking water treatment because they are stronger disinfectants than free chlorine is true. 8. Both A and B method of using activated carbon allows the saturated carbon to be reactivated.9. Reverse osmosis is the best membrane technology for the removal of microorganisms, including viruses, from a water source.
7. Chloramines are typically used in drinking water treatment because they are stronger disinfectants than free chlorine.
8. PAC added during coagulation/flocculation and GAC cap on top of a sand filter or a GAC contactor both allow for the saturated carbon to be reactivated.
9. Reverse osmosis is the best membrane technology for removing microorganisms, including viruses, from a water source.
10. Double layer compression coagulation-flocculation mechanism is more likely to occur if a high dose of alum is used and the pH of the water is high. The correct answer is option(d).
A high dose of alum and a high water pH favors double-layer compression as the coagulation-flocculation mechanism.
To know more about disinfectants please refer:
https://brainly.com/question/30279809
#SPJ11
A light source for a fiber optic cable is known as which of the following?
A.Optical Transmitter
B.Light Transmitter
C.Optical Retina
D.Cladding
The light source for a fiber optic cable is known as Cladding.
Cladding is a process that is carried out to protect the optical fibers from any external damage or disturbance and to provide high efficiency. This process involves a layer of material that is attached to the exterior of the fiber optic cable to safeguard it from humidity, physical shocks, and other possible outside interference. Fiber optic cables are made of glass and are thin, therefore, the cladding has to be of similar thickness to that of the fiber optic cable so that the two can be fitted together smoothly. The cladding layer is used to confine light within the fiber optic cable by causing light rays to reflect from the interior surface of the cladding. The cladding provides a reflective surface that forces the light to travel down the fiber, while also lowering energy loss.
Cladding boards can be produced using a wide assortment of materials like wood, metal, block or vinyl, and are frequently combined with composite materials that can incorporate aluminum wood mixes of concrete and reused polystyrene wheat rice straw strands.
Know more about Cladding, here:
https://brainly.com/question/31561840
#SPJ11