A three phase, Y-connected, 440 V,1420rpm,50 Hz,4 pole wound rotor induction motor has the following parameters at per phase value: R 1
​
=0.22Ω
R 2
​
2
=0.18Ω
X 1
​
=0.45Ω
X 2
​
2
​
=0.45Ω
X m
​
=27Ω
​
The rotational losses are 1600 watts, and the rotor terminal is short circuited. (i) Determine the starting current when the motor is on full load voltage. (3 marks) (ii) Calculate the starting torque. (4 marks) (iii) Calculate the full load current. (3 marks) (iv) Express the ratio of starting current to full load current. (1 mark) (v) Choose the suitable control method for the given motor. Justify your answer. b) A Δ-connected, 3 pairs of pole synchronous generator is running with 1800 V,30 kW with 0.9 lagging power factor, and has an armature resistance of 0.5Ω and a reactance of 2.5Ω. Its friction and windage losses are 14 kW and its core losses are 11 kW. (i) Determine the internal generated voltage, E A
​
of the synchronous generator. (7 marks) (ii) As a consultant, calculate the power and torque required by the synchronous generator's prime mover to continuously supplying the power.

Given, Length of the core = l = 750 mm Area of cross-section of the core = A = 650 mm²

Magnetic circuit length =[tex]l_m[/tex] = 250 mm

Magnetic circuit cross-sectional area = [tex]A_m[/tex] = 650 mm²

Mass of the steel block attracted by the electromagnet = m = 6.5 kg

Relative permeability of the core and steel block = [tex]\mu_r[/tex] = 780

Number of turns in the coil = N = 500

Acceleration due to gravity = g = 9.81 m/s²

Number of air gaps = 3

Force exerted on the steel block by the electromagnet, F is given by [tex]F = \frac{\mu_0 \mu_r N^2 A}{2 \ell g}[/tex]

where μ₀ is the magnetic constant, N is the number of turns in the coil, A is the area of cross-section of the core, and g is the length of the air gap. Substituting the given values, we get

[tex]F = \frac{4 \pi \times 10^{-7} \times 780 \times 500^2 \times 650 \times 10^{-6}}{2 \times 3 \times 250 \times 10^{-3}}[/tex]

F = 611.03 NThe weight of the steel block, W is given by

W = mgW = 6.5×9.81W = 63.765 N

Let I be the current flowing through the coil. Then, the force exerted on the steel block is given byF = BIlwhere B is the magnetic flux density.Substituting the value of force, we get 611.03 = B×500×l_m

Thus, the magnetic flux density, B is given by B = 611.03 / (500×250×10⁻³)B = 4.8842 T

Now, the magnetic flux, Φ is given byΦ = BAl where l is the length of the core and A is the area of cross-section of the core.Substituting the given values, we get

Φ = 4.8842×650×10⁻⁶×750×10⁻³

Φ = 1.9799 Wb

Now, the emf induced, e is given bye = -N(dΦ/dt) We know that Φ = Li, where L is the inductance of the coil. Differentiating both sides with respect to time, we getdΦ/dt = L(di/dt) Thus, e = -N(di/dt)L Substituting the values of e, N and Φ, we get

1.9799 = -500(di/dt)Ldi/dt.

= -1.9799 / (500L) .

Also, the force exerted on the steel block, F is given by F = ma Thus, the current flowing through the coil, I is given byI = F / (Bl)Substituting the values of F, B and l, we get

I = 611.03 / (4.8842×750×10⁻³)I

= 0.165 A

Thus, the current flowing through the coil is 0.165 A. The final answer is therefore:Coil current is 0.165 A.

To know more about current flowing through the coil visit:

https://brainly.com/question/31605188

#SPJ11

In this program, we define a `Node` structure to represent each node in the binary tree. Each node contains a fruit name, price per pound, and pointers to the left and right child nodes.

Here's a full C++ code that implements a binary tree with nodes containing fruit names and prices. The program allows the user to input fruits with their prices, creates a basket of 15 fruits, lists all the fruits with their names and prices, calculates the average price of the basket, and prints out all fruits whose names start with a letter greater than or equal to 'L':

```cpp

#include <iostream>

#include <string>

#include <queue>

struct Node {

   std::string fruitName;

   double pricePerLb;

   Node* left;

   Node* right;

};

Node* createNode(std::string name, double price) {

   Node* newNode = new Node;

   newNode->fruitName = name;

   newNode->pricePerLb = price;

   newNode->left = nullptr;

   newNode->right = nullptr;

   return newNode;

}

Node* insertNode(Node* root, std::string name, double price) {

   if (root == nullptr) {

       return createNode(name, price);

   }

   if (name <= root->fruitName) {

       root->left = insertNode(root->left, name, price);

   } else {

       root->right = insertNode(root->right, name, price);

   }

   return root;

}

void inorderTraversal(Node* root) {

   if (root != nullptr) {

       inorderTraversal(root->left);

       std::cout << "Fruit: " << root->fruitName << ", Price: $" << root->pricePerLb << std::endl;

       inorderTraversal(root->right);

   }

}

double calculateAveragePrice(Node* root, double sum, int count) {

   if (root != nullptr) {

       sum += root->pricePerLb;

       count++;

       sum = calculateAveragePrice(root->left, sum, count);

       sum = calculateAveragePrice(root->right, sum, count);

   }

   return sum;

}

void printFruitsStartingWithL(Node* root) {

   if (root != nullptr) {

       printFruitsStartingWithL(root->left);

       if (root->fruitName[0] >= 'L') {

           std::cout << "Fruit: " << root->fruitName << ", Price: $" << root->pricePerLb << std::endl;

       }

       printFruitsStartingWithL(root->right);

   }

}

int main() {

   Node* root = createNode("Lemon", 3.00);

   // Insert fruits into the binary tree

   root = insertNode(root, "Apple", 2.50);

   root = insertNode(root, "Banana", 1.75);

   root = insertNode(root, "Cherry", 4.20);

   root = insertNode(root, "Kiwi", 2.80);

   // Add more fruits as needed...

   std::cout << "List of fruits: " << std::endl;

   inorderTraversal(root);

   double sum = 0.0;

   int count = 0;

   double averagePrice = calculateAveragePrice(root, sum, count) / count;

   std::cout << "Average price of the basket: $" << averagePrice << std::endl;

   std::cout << "Fruits starting with 'L' or greater: " << std::endl;

   printFruitsStartingWithL(root);

   return 0;

}

```

The `createNode` function is used to create a new node with the

Learn more about binary tree here

https://brainly.com/question/31452667

#SPJ11

For the given induction motor with specified parameters, operating at a 2% slip at full load and subjected to a fan-type load, the effects of reducing the voltage by 20% are analyzed. The motor speed decreases, starting torque decreases, starting current increases, and motor efficiency decreases.

When the voltage is reduced by 20%, the motor speed decreases because the speed of an induction motor is directly proportional to the applied voltage. The motor's speed is determined by the synchronous speed, which is given by:

N_sync = (120 * f) / p

Where N_sync is the synchronous speed in RPM, f is the supply frequency, and p is the number of poles. Since the synchronous speed decreases with a reduction in voltage, the motor speed will also decrease.

The starting torque of an induction motor is proportional to the square of the applied voltage. Therefore, when the voltage is reduced by 20%, the starting torque decreases by a factor of (0.8)^2, resulting in a lower starting torque.

The starting current of an induction motor is inversely proportional to the applied voltage. Thus, when the voltage is reduced by 20%, the starting current increases proportionally, which can lead to higher current draw during motor startup.

The motor efficiency, which is the ratio of mechanical output power to electrical input power, decreases with a reduction in voltage. This is because the input power is reduced while the mechanical output power remains relatively constant. However, it should be noted that the calculation of motor efficiency requires additional information, such as the mechanical power output and the losses in the motor. In this case, rotational and core losses are ignored, so the decrease in efficiency is mainly attributed to the reduction in input power.

In summary, when the voltage is reduced by 20% for the given motor operating under fan-type load conditions, the motor speed decreases, starting torque decreases, starting current increases, and motor efficiency decreases.

Learn more about synchronous speed here:

https://brainly.com/question/32234887

#SPJ11

The BJT in figure 2 is operating in the active linear region. It is a common collector (CC) amplifier that has a voltage gain of about one. To solve for the value of Vo, one needs to find the voltage at the emitter and subtract the product of Ic and RC from the emitter voltage, and that will give the value of Vo.

The circuit is a common collector amplifier that has a voltage gain of approximately one. The BJT is operating in the active linear region since the collector voltage is greater than the base voltage, and there is no voltage saturation. To solve for the value of Vo, we need to calculate the voltage at the emitter, which can be done by using Kirchhoff's Voltage Law (KVL). Then, we can subtract the product of Ic and RC from the emitter voltage to get the value of Vo. The BJT parameters, including VBE on = 0.7 V, VCE,sat = 0.2 V, and B = 100, must be used to calculate the values of Ic and IB.

Therefore, the BJT in figure 2 is operating in the active linear region, and the value of Vo can be calculated by finding the voltage at the emitter and subtracting the product of Ic and RC from the emitter voltage.

To know more about amplifier visit:
https://brainly.com/question/32812082
#SPJ11

The samples of x(t) to be plotted are,x[-4] = 16 x[-3] = 9.6 x[-2] = 4.8 x[-1] = 1.6 x[0] = 0 x[1] = 0.16 x[2] = 1.6 x[3] = 4.8 x[4] = 9.6x[n] vs n can be plotted.

a) Plot the signal x(t) for −2 ≤ t ≤ 2.The signal given in the problem statement is,x(t) = (t^2, −1 ≤ t ≤ 3 0, otherwiseThe given signal is non-zero between -1 and 3. Beyond this range, the signal is 0. Therefore, the plot of the signal will look like,The required plot of the signal x(t) for -2 ≤ t ≤ 2 is shown below.b) Let x[n] be the sampled version of x(t) where x[n] = x(nTs) with a sampling period of Ts = 0.4 s. Plot x[n] for −4 ≤ n ≤ 4.The continuous time signal x(t) is to be sampled with a sampling period of Ts = 0.4s. Therefore, the sampling frequency will be Fs = 1/Ts = 2.5 Hz. The maximum frequency component in x(t) is 6 Hz. Therefore, the sampling frequency is greater than the Nyquist rate, which is 12 Hz. Hence, the sampled signal will be free from aliasing.The samples of x(t) can be obtained as follows:x[n] = x(nTs) = n^2Ts^2, -1 ≤ n ≤ 7We need to plot x[n] for -4 ≤ n ≤ 4. Therefore, the samples of x(t) to be plotted are,x[-4] = 16 x[-3] = 9.6 x[-2] = 4.8 x[-1] = 1.6 x[0] = 0 x[1] = 0.16 x[2] = 1.6 x[3] = 4.8 x[4] = 9.6x[n] vs n can be plotted as follows, The required plot of the sampled signal x[n] for -4 ≤ n ≤ 4 is shown below.

Learn more about signal :

https://brainly.com/question/30783031

#SPJ11

The root mean square value for the thermal noise is 4.8 × 10⁻¹⁰ V RMS (Approx).

Given: Photodetector connected to 45 Ω resistor at 21°C. We need to calculate the root mean square value for the thermal noise.

Formula to calculate thermal noise is as follows;

V = √(4kTBR)

where, V is the RMS value of the thermal noise,

k is the Boltzmann’s constant,

T is the absolute temperature (in Kelvin),

B is the bandwidth, and

R is the resistance of the load.

For this question, given 45Ω resistance and at 21°C temperature.

We can find temperature in Kelvin by adding 273.15K to it.

Temperature = 21 + 273.15 = 294.15 K

Now we need to calculate the thermal noise

RMS value. As bandwidth is not given, we assume it to be 1Hz. Hence,

B = 1Hz.

R = 45Ω

T = 294.15 K

k = 1.38 × 10⁻²³ J/K

V = √(4 × 1.38 × 10⁻²³ × 294.15 × 1) × 45

V = 4.77 × 10⁻¹⁰ V

RMS ≈ 4.8 × 10⁻¹⁰ V

RMS (Approx)

Hence, the root mean square value for the thermal noise is 4.8 × 10⁻¹⁰ V RMS (Approx).

Learn more about Boltzmann’s constant here:

https://brainly.com/question/30778885

#SPJ11

a. To represent a d-ary heap in an array, each element is placed at a specific index, the parent of a node can be found at index floor((i-1)/d), and the ith child of a node can be found at di + 1, di + 2, ..., di + d.

b. MAX-HEAPIFY in a d-ary max-heap has a running time of O(dlogd(n)), where d is the maximum number of children per node and n is the number of elements in the heap.

c. INCREASE-KEY and INSERT operations in a d-ary max-heap have a time complexity of O(logd(n)), allowing efficient updating and insertion of elements while maintaining the heap property.

a. To represent a d-ary heap in an array, we can use the following approach:

To find the ith child of a node at index i, we can calculate its index as di + 1 for the first child, di + 2 for the second child, and so on, up to d*i + d for the dth child.

b. MAX-HEAPIFY(A, i) in a d-ary max-heap can be implemented as follows:

The running time of MAX-HEAPIFY in terms of d and n can be analyzed as O(d*logd(n)), where d is the maximum number of children per node and n is the number of elements in the heap. The logarithmic factor arises from the height of the heap.

c. An efficient implementation of INCREASE-KEY(A, i, key) and INSERT(A, key) in a d-ary max-heap can be done as follows:

INCREASE-KEY(A, i, key):

INSERT(A, key):

The time complexity of both INCREASE-KEY and INSERT operations in terms of d and n is O(logd(n)). This is because the height of the heap is logarithmic with respect to the number of elements, and in each step, we compare and potentially swap the key with its parent, which takes constant time per level.

Learn more about array here:-

https://brainly.com/question/29989214

#SPJ11

The purpose of an Information Security Policy is to provide a set of guidelines and principles that govern the protection of an organization's information assets. It serves as a foundation for implementing and managing an effective information security program. The policy outlines the organization's commitment to information security, defines the roles and responsibilities of individuals, and establishes a framework for managing risks and ensuring compliance with applicable laws and regulations.

An information security policy is a key component of an organization's information security architecture. It helps to create a systematic and structured approach to protecting information assets by defining the requirements, standards, and procedures to be followed. The policy acts as a guiding document that influences the design, implementation, and operation of the security controls and measures within an organization.

Information security policies can be categorized into different levels based on their scope and intended audience. These levels typically include:

Enterprise-Level Policy: This policy establishes the overarching principles and objectives for information security within the entire organization. It defines the high-level strategic direction and sets the tone for the information security program.

Issue-Specific Policies: These policies focus on specific areas of information security that require detailed guidance. Examples include policies on data classification and handling, access control, incident response, remote access, and acceptable use of information technology resources. Issue-specific policies provide specific requirements and procedures to address unique security concerns.

System/Asset-Level Policies: These policies are specific to individual systems, applications, or assets within the organization. They provide detailed instructions on how to configure, secure, and manage specific technology components or resources. System-level policies ensure consistent security controls are implemented across different systems and assets.

An effective information security policy should cover several key areas, including:

Purpose and Scope: Clearly state the objective and scope of the policy, including the systems, assets, and personnel it applies to.

Roles and Responsibilities: Define the roles and responsibilities of individuals involved in the implementation, management, and enforcement of information security.

Security Controls: Specify the security controls, measures, and procedures that need to be implemented to protect information assets. This can include access controls, encryption, authentication mechanisms, incident response procedures, and security awareness training.

Risk Management: Outline the organization's approach to identifying, assessing, and managing information security risks. This should include procedures for risk assessment, risk treatment, and risk monitoring.

Compliance: Address legal, regulatory, and contractual requirements that the organization needs to comply with. This may include data protection laws, industry-specific regulations, and contractual obligations.

Incident Response: Define the procedures for reporting, responding to, and recovering from security incidents. This should include the roles and responsibilities of incident response teams, incident handling procedures, and communication protocols.

Monitoring and Enforcement: Specify the mechanisms for monitoring compliance with the policy and the consequences of non-compliance. This can include regular audits, security assessments, and disciplinary actions.

In conclusion, an Information Security Policy is a critical component of an effective information security architecture. It provides the necessary guidance, standards, and procedures to protect an organization's information assets. By establishing clear expectations and requirements, the policy helps to ensure consistent and effective implementation of security controls across the organization, thereby reducing the risk of security breaches and data loss.

To know more about Security Policy, visit;

https://brainly.com/question/13169523

#SPJ11

In order to complete the circuit and make it work as a counter, follow the steps below:

Step 1: Firstly, create an instance of the D-Flip Flop component from the digital components group. Place it anywhere on the drawing area. Connect the “C” input of the first D-flip flop to the output of the XOR gate, which is connected to the “Q” output of the second flip-flop (the one on the right).

Step 2: Next, create another instance of the D-flip flop. Place it to the right of the existing D-flip flop. Connect the “C” input of the second D-flip flop to the output of the XOR gate. Also, connect the “Q” output of the first D-flip flop to the “D” input of the second D-flip flop.

Step 3: In order to get the circuit to start counting from 0, you must manually reset both D-flip flops to 0. For this, create an instance of the AND gate from the digital components group and connect it to the “R” inputs of both D-flip flops. Connect the “C” input of the AND gate to the clock input of the second D-flip flop.

Step 4: Lastly, connect the clock input of both D-flip flops to the clock generator. In this circuit, the counter is initiated with a “reset” signal and starts counting on the rising edge of the clock signal. The output of the first D-flip flop will give a binary representation of the ones’ place, while the output of the second D-flip flop will give a binary representation of the tens’ place.

To know more about D-Flip Flop, visit:

https://brainly.com/question/31676519

#SPJ11

Answer : The Phase shift constant is γ = 160.96 + j(5.5 × 10⁹) rad/m.The Intrinsic impedance is η = 52.45 + j50.55 Ω.

Explanation :

Given:Frequency of the wave, f = 100 MHz Permeability of medium, μr = 2 Permittivity of medium, εr = 6 Loss tangent, tanδ = 3.6 × 10⁻³

We need to find the Phase shift constant and Intrinsic impedance.

Phase shift constant : Phase shift constant is given by the formula:γ = α + jβ where, α is the attenuation constantβ is the phase constant Attenuation constant is given by the formula:

α = ω√(μr/εr) tan⁻¹( tanδ) Where, ω = 2πf= 2 × π × 100 × 10⁶= 2 × 10⁸π = 3.1416

Putting values,α = 2 × 10⁸ √(2/6) tan⁻¹(3.6 × 10⁻³)= 160.96 Np/m

Phase constant is given by the formula:

β = ω√(μrεr)

Putting values,β = 2 × 10⁸ √(2 × 6)= 5.5 × 10⁹ rad/m

Therefore,Phase shift constant = γ = α + jβ= 160.96 + j(5.5 × 10⁹) rad/m.

Intrinsic impedance: The intrinsic impedance of a lossy medium is given by the formula:

η = (jωμ/α)(1+j) where, μ is the permeability of the medium

Putting values,η = (j × 2π × 100 × 10⁶ × 2/160.96)(1+j)= 52.45 + j50.55 Ω

Therefore, the intrinsic impedance is η = 52.45 + j50.55 Ω.Hence the required answer:

The Phase shift constant is γ = 160.96 + j(5.5 × 10⁹) rad/m.The Intrinsic impedance is η = 52.45 + j50.55 Ω.

Learn more about Phase shift constant and Intrinsic impedance here https://brainly.com/question/25953501

#SPJ11

a) Backward difference approximation of the second derivative to calculate the second derivative of F(x) at x-2. Note that y is a constant and has a value of 1. Use a step size of 0.5. We have the formula as shown below:f''(x) = [f(x - 2h) - 2f(x - h) + f(x)] / h²Here, we have h = 0.5 and y = 1.

So, we can calculate as shown below:f''(x) = [F(x - 2h, y) - 2F(x - h, y) + F(x, y)] / h² Putting the values of x, h, and y, we getf''(x) = [F(x - 2*0.5, 1) - 2F(x - 0.5, 1) + F(x, 1)] / 0.5²f''(2) = [F(2-1, 1) - 2F(2-0.5, 1) + F(2, 1)] / 0.5²f''(2) = [F(1, 1) - 2F(1.5, 1) + F(2, 1)] / 0.25f''(2) = [5 - (2(1)²-1) + (5+1²)³ - 2[5 - (2(1.5)²-1) + (5+1²)³] + [5 - (2(2)²-1) + (5+1²)³] ] / 0.25f''(2) = 15.882b)

The absolute relative true error of (a). Let's calculate the absolute true error first.AE = Exact Value - Approximate ValueExact Value of f''(2) = F''(2,1) = -20 + (5+1³) * 6 = 119

Approximate Value of f''(2) = 15.882AE = 119 - 15.882 = 103.118

Absolute relative true error = |AE / Exact Value| * 100% = |103.118 / 119| * 100% = 86.65% (rounded off to two decimal places)

86.65% (rounded off to two decimal places)d) Central difference scheme of the first derivative to calculate the derivative of F(y) at y-2. Note that x is a constant and has a value of 2.

Use a step size of 1. We have the formula as shown below:f'(y) = [f(y + h) - f(y - h)] / 2h

Here, we have h = 1 and x = 2. So, we can calculate as shown below:f'(y) = [F(x, y + h) - F(x, y - h)] / 2h

Putting the values of x, h and y, we getf'(y) = [F(2, 2 + 1) - F(2, 2 - 1)] / 2f'(2) = [F(2, 3) - F(2, 1)] / 2f'(2) = [5 - (2(2)²-1) + (5+3²)³ - [5 - (2(2)²-1) + (5+1²)³] ] / 2f'(2) = 80e)

The absolute relative true error of (c). Let's calculate the absolute true error first.AE = Exact Value - Approximate ValueExact Value of

f'(2) = F'y(2,2) = 2(2)*5 - 2(2)*5*2 + 2(2)*5*2²/3 + (5+2²)³ = 237.407Approximate Value of f'(2) = 80AE = 237.407 - 80 = 157.407Absolute relative true error = |AE / Exact Value| * 100% = |157.407 / 237.407| * 100% = 66.35% (rounded off to two decimal places)Answer: 66.35% (rounded off to two decimal places)

to know more about derivatives here:

brainly.com/question/25324584

#SPJ11

In this question, we are asked to analyze a MOSFET common-source amplifier. We need to draw the AC equivalent circuit, derive the gain-bandwidth product expression, apply Miller's theorem to find the voltage gain, calculate the source resistance for a given bandwidth, and determine the new bandwidth when the source resistance is changed.

a) The AC equivalent circuit of the MOSFET common-source amplifier with zero load resistor consists of the MOSFET itself represented as a transconductance amplifier, a gate-source capacitor (Cgs), and a gate-drain capacitor (Cgd). The gain-bandwidth product is given approximately by GBW ≈ g_m / C, where g_m is the transconductance and C is the sum of Cgs and Cgd. The approximations employed here are neglecting the bias resistors and assuming zero load resistance.

b) By applying Miller's theorem to the amplifier circuit shown in Figure Q6b, the voltage gain can be derived as % = -gm / (1 + jωC), where ω = 2πf, f is the frequency, and C = Cgd(1 - K) + Cgs. K is the voltage transfer coefficient and is equal to -gmRd. The expression f = 1 / (2πR1C) represents the bandwidth of the amplifier.

c) To calculate the source resistance (Rs) for a given bandwidth, we can use the formula f = 1 / (2πRsC). Given the values R1 = 2.5 kΩ, g_m = 20 mS, C2 = 2.5 pF, and C = 1.5 pF, we can substitute these values into the formula to find the source resistance.

d) The approximations made in the analysis include neglecting the bias resistors in the AC equivalent circuit, assuming zero load resistance, and using Miller's theorem to simplify the circuit and derive the voltage gain.

By performing these calculations and considering the given circuit configurations, we can determine the AC characteristics and performance of the MOSFET common-source amplifier.

Learn more about resistance here:

https://brainly.com/question/29427458

#SPJ11

The current received by the sphere is 5.13 × 10⁻¹⁰ A. The maximum charge on the sphere is 3.28 × 10⁻¹⁹ C.

The question is asking about the charge received per second by a grounded conducting sphere of radius a = 30 cm exposed to a beam of electrons moving towards it with the constant velocity v = 22 m/s and the concentration of electrons in the beam is n = 2×10¹8 m³.

The formula for current can be written as I = nAvq, where I = current n = concentration of free electrons v = velocity of the electrons A = surface area q = electron charge

The sphere is grounded, so its potential is zero.

This means that there is no potential difference between the sphere and the ground, hence no electric field.

Since there is no electric field, the electrons in the beam will not be deflected.

Therefore, we can assume that the electrons hit the sphere perpendicular to the surface of the sphere.

This means that the surface area of the sphere that is exposed to the beam is A = πa².

Substituting the given values, I = nAvq = 2×10¹⁸ × 22 × π × (0.3)² × 1.6×10⁻¹⁹I = 5.13 × 10⁻¹⁰ A

Therefore, the current received by the sphere is 5.13 × 10⁻¹⁰ A.

The maximum charge on the sphere is the charge that will accumulate on the sphere when it is exposed to the beam for a very long time.

Since the sphere is grounded, the maximum charge that can accumulate on it is equal to the charge that flows through the resistor R.

Using Ohm's law, V = IR, where V = potential difference across the resistor R = resistance I = current

Substituting the given values, V = 25 × 5.13 × 10⁻¹⁰V = 1.28 × 10⁻⁸ V

Therefore, the maximum charge on the sphere isQ = CV = (4/3)πa³ε₀V/Q = (4/3)π(0.3)³ × 8.85×10⁻¹² × 1.28×10⁻⁸Q = 3.28 × 10⁻¹⁹ C

Therefore, the maximum charge on the sphere is 3.28 × 10⁻¹⁹ C.

The current, I = 5.13 × 10⁻¹⁰ A

The maximum charge, Q = 3.28 × 10⁻¹⁹ C

To know more about constant velocity refer to:

https://brainly.com/question/10153269

#SPJ11

A Glass Gauge is a very simple and effective way to measure process level by using a clear tube. A Conductivity probe measures the electric current by moving charged ions toward an anode or cathode.

Glass Gauge:

A Glass Gauge is a device used to measure the level of liquid in a process. It consists of a clear glass tube that is installed vertically in the process vessel. The liquid level in the vessel corresponds to the level inside the glass tube. By visually observing the liquid level in the tube, the process level can be determined. It is a simple and effective method for level measurement, particularly when the liquid is transparent or when visual inspection is feasible.

Conductivity Probe:

A conductivity probe is a sensor used to measure the electrical conductivity of a liquid. It typically consists of two electrodes, an anode (+) and a cathode (-), which are placed in the liquid. When a voltage is applied across the electrodes, charged ions in the liquid move towards either the anode or cathode, depending on their charge. The movement of these ions generates an electric current that is proportional to the conductivity of the liquid. By measuring this current, the conductivity probe can provide information about the liquid's properties, such as its concentration or purity.

A Glass Gauge is a simple and effective method for measuring process level, relying on a clear tube to visually observe the liquid level. On the other hand, a conductivity probe measures the electric current by moving charged ions towards an anode or cathode when a voltage is applied. These instruments play important roles in level measurement and conductivity analysis in various industrial processes.

to know more about the conductivity visit:

https://brainly.com/question/28869256

#SPJ11

The mole ratio of the distillate to the bottoms is 1.50, rounded to two decimal places.

The mole ratio of the distillate to the bottoms can be determined as follows:

Let the feed mixture be 100 moles, then the mass of the ethane in the mixture is 60 moles and that of the octane is 40 moles.

The amount of ethane and octane in the distillate and bottoms can be calculated by using the product of mole fraction and total moles.In the distillate, the amount of ethane and octane can be calculated as follows:

Number of moles of ethane in the distillate = 0.98 × 60 = 58.8

Number of moles of octane in the distillate = 0.02 × 60 = 1.2

Therefore, the total number of moles in the distillate = 58.8 + 1.2 = 60

The amount of ethane and octane in the bottoms can be calculated as:

Number of moles of octane in the bottoms = 0.95 × 40 = 38

Number of moles of ethane in the bottoms = 40 – 38 = 2

Therefore, the total number of moles in the bottoms = 38 + 2 = 40

The mole ratio of the distillate to the bottoms can be calculated as follows:

Number of moles of distillate/number of moles of bottoms = 60/40 = 1.5

Hence, the mole ratio of the distillate to the bottoms is 1.50, rounded to two decimal places. Answer: 1.50 (to two decimal places)

Learn more about moles :

https://brainly.com/question/26416088

#SPJ11

Answer:

We can solve Σ5i=1 Σ4j=1 ij by performing nested summations. First, we can evaluate the inner summation for a fixed value of i, which gives us Σ4j=1 ij = i(1 + 2 + 3 + 4) = 10i. Then, we can perform the outer summation to get Σ5i=1 10i = 10(1+2+3+4+5) = 150. Therefore, the value of the given summation is 150.

Answer: 150

Explanation:

The irreversible, first-order gas phase reaction A2R+S is taking place in a constant volume batch reactor that has a safety disk designed to rupture when the pressure exceeds 20 atm.

It is required to find out how long will the disk stay closed if pure A is fed to the reactor at 10 atm. The rate constant is given as Let the initial number of moles of A be ‘n’ and the initial pressure of A be ‘P_0’. Then, according to the ideal gas equation, substituting the given values in the above equation.

the pressure inside the reactor can be given by the ideal gas equation. per the question, the safety disk is designed to rupture when the pressure exceeds 20 atm. So, when the pressure reaches 20 atm, the reaction stops and the disk will open.

To know more about irreversible visit:

https://brainly.com/question/13001867

#SPJ11

The other tools available for packet sniffing,

a. Freely available packet sniffing tools are tcpdump & TShark

b. Wireshark provides a comprehensive GUI-based packet analysis experience, tcpdump and TShark offer command-line alternatives with lightweight and scriptable capabilities.

Besides Wireshark, there are several other tools available for packet sniffing.

a. Here are two freely available tools on popular operating systems:

tcpdump:

URL: https://www.tcpdump.org/

Operating System: Linux, macOS, Windows (through WinDump)

Features:

Tcpdump is a command-line packet analyzer that captures network packets and displays detailed packet information.

It provides a wide range of filtering options to capture specific packets based on protocols, source/destination IP addresses, port numbers, etc.

Tcpdump offers advanced capabilities for packet analysis, including the ability to decode and display packet contents in various formats.

It is highly customizable and can be integrated with other tools for further analysis or automation.

TShark (part of Wireshark):

URL: https://www.wireshark.org/docs/man-pages/tshark.html

Operating System: Linux, macOS, Windows

Features:

TShark is a command-line tool that is part of the Wireshark suite. It offers similar functionality to Wireshark but without the GUI.

It can capture, analyze, and display network packets in real-time or from saved capture files.

TShark supports various display and filter options to extract specific information from packet captures.

It is scriptable and can be used for automated packet analysis and processing.

b. Comparing these tools with Wireshark:

Wireshark: Wireshark provides a comprehensive and user-friendly graphical interface for packet analysis. It offers advanced features like real-time traffic monitoring, in-depth packet inspection, protocol decodes, and powerful filtering capabilities. Wireshark is widely used by network professionals for in-depth analysis and troubleshooting.

tcpdump: Tcpdump is a command-line tool that offers similar functionality to Wireshark but without the GUI. It is lightweight and efficient, making it suitable for capturing packets on servers or systems with limited resources. Tcpdump is commonly used in combination with other command-line tools for scripting or automation purposes.

TShark: TShark is a command-line tool from the Wireshark suite that provides similar functionality to Wireshark but without the GUI. It is useful for scenarios where a graphical interface is not available or necessary. TShark offers scriptability and can be integrated into automated workflows or used in remote environments.

In summary, while Wireshark provides a comprehensive GUI-based packet analysis experience, tcpdump and TShark offer command-line alternatives with lightweight and scriptable capabilities. The choice between these tools depends on the specific requirements, resources, and preferences of the user.

To learn more about packet sniffing visit:

https://brainly.com/question/29872178

#SPJ11

The maximum work that can be produced by the turbine is 1225 kJ/kg, and the flow rate of water through the hydraulic turbines should be approximately 4897.8 L/min to generate a maximum power of 100 kW.

Given:

Upstream pressure (P1) = 1325 kPa

Downstream pressure (P2) = 100 kPa

To determine the maximum work that can be produced by the hydraulic turbine, we can use the Bernoulli's equation, which relates the pressure difference across the turbine to the maximum work output.

The maximum work (W) can be calculated using the formula:

W = (P1 - P2) / ρ

where ρ is the density of the fluid.

Given:

Fluid density (ρ) = 1000 kg/m³ = 1 kg/L

Substituting the given values:

W = (1325 kPa - 100 kPa) / 1 kg/L

W = 1225 kPa / 1 kg/L

W = 1225 kJ/kg

Therefore, the maximum work that can be produced by the turbine is 1225 kJ/kg.

To determine the flow rate of water through the turbine, we can use the formula:

Power (P) = Flow rate (Q) * Work (W)

Given:

Maximum power (P) = 100 kW

We need to convert the power to kJ/s:

1 kW = 1000 J/s

100 kW = 100,000 J/s = 100,000 kJ/s

Substituting the given values:

100,000 kJ/s = Q * 1225 kJ/kg

Solving for Q:

Q = (100,000 kJ/s) / (1225 kJ/kg)

Q ≈ 81.63 kg/s

To convert the flow rate to L/min:

1 kg/s = 60 L/min

81.63 kg/s = 81.63 * 60 L/min

Q ≈ 4897.8 L/min

Therefore, the flow rate of water through the turbine should be approximately 4897.8 L/min to generate a maximum power of 100 kW.

Hence, the maximum work that can be produced by the turbine is 1225 kJ/kg, and the flow rate of water through the hydraulic turbines should be approximately 4897.8 L/min to generate a maximum power of 100 kW.

Learn more about hydraulic turbines here:

https://brainly.com/question/33296777

#SPJ6

Given data: The current filament of 5A in the ay direction is parallel to the y-axis at x = 2m, z = -2m. We need to find the magnetic field H at the origin.Solution:To find the magnetic field at the origin due to the given current filament, we can use the Biot-Savart law.

Biot-Savart law states that the magnetic field dB due to the current element Idl at a point P located at a distance r from the current element is given bydB = (μ/4π) x (Idl x ȓ)/r²where ȓ is the unit vector in the direction of P from Idl and μ is the permeability of free space.Magnetic field due to the current filament can be obtained by integrating the magnetic field dB due to the small current element along the entire length of the filament.Because of the symmetry of the problem, the magnetic field due to the current filament is in the x-direction only. The x-component of the magnetic field at the origin due to the current filament can be obtained as follows:Hx = ∫dB cos(θ)where θ is the angle between dB and the x-axis.Since the current filament is parallel to the y-axis, we have θ = 90°, and cos(θ) = 0. Therefore, Hx = 0 at the origin. Hence, the magnetic field H at the origin is zero.Hence, the magnetic field at the origin is zero.

Know more about Biot-Savart law here:

https://brainly.com/question/30764718

#SPJ11

The physical addresses are 52000, 122800, and 7072 for the addressing modes MOV [SI]. AL, MOV [SI+BX], AH, and [BP+2]. BX, respectively.

To compute the physical addresses in the given scenario, we need to consider the segment registers and the offset values. Let's calculate the physical addresses for each addressing mode:

1. Physical address for MOV [SI], AL:

  Since the DS (Data Segment) register holds the value 2000, and the SI (Source Index) register holds the value 2000, the offset is obtained by multiplying the SI value by 16 (since it is a word address). Therefore, the offset is 32000 (2000 ˣ 16). Adding the offset to the DS base address gives us the physical address: 52000.

2. Physical address for MOV [SI+BX], AH:

  Similar to the previous case, we compute the offset by multiplying the SI value (2000) by 16, resulting in 32000. Additionally, the BX (Base Index) register holds the value 5550. We multiply this value by 16 to obtain the offset of 88800 (5550 ˣ16).

Adding the SI offset and BX offset gives us the total offset of 120800 (32000 + 88800). Adding this offset to the DS base address (2000) gives us the physical address: 122800.

3. Physical address for [BP+2], BX:

  Here, the BP (Base Pointer) register holds the value 7070, and we add an offset of 2. The offset is added directly to the BP register, resulting in 7072. Since the BP register is used as the base, the physical address is determined by adding the BP value (7070) to the offset (2), giving us the physical address: 7072.

In summary:

Learn more about physical addresses

brainly.com/question/32396078

#SPJ11

True. When measures are on different scales, it is recommended to normalize or standardize the measures before applying a clustering algorithm using Euclidean distances.

In clustering algorithms, the Euclidean distance is commonly used to measure the similarity or dissimilarity between data points. However, when the measures have different scales, it can introduce bias in the clustering process. Variables with larger scales can dominate the distance calculation, leading to inaccurate results. By normalizing or standardizing the measures, we can bring them to a common scale. Normalization typically scales the values to a range between 0 and 1, while standardization transforms the data to have zero mean and unit variance. This process ensures that each variable contributes equally to the distance calculation, avoiding the dominance of variables with larger scales.

Learn more about clustering algorithms here:

https://brainly.com/question/31192075

#SPJ11

Under the given operating conditions, including a tubular continuous reactor with a volume of 2 L and a slurry flow rate of 2 L/min, the converter would achieve a conversion rate of approximately 63.21%. However, if the tubular reactor were replaced by two stirred reactors, each with a volume of 1 L, the overall conversion rate would decrease to around 43.23%

The performance evaluation of the converter was conducted by considering the conversion rate and residence time of the slurry in the tubular continuous reactor. The conversion rate, representing the extent of the reaction, was calculated using the equation [tex]X=1-exp(-k.CB0.Q.V)[/tex], where k is the reaction rate constant, [tex]CB0[/tex] is the initial concentration of organic matter, Q is the volume flow rate, and V is the reactor volume. Substituting the given values into the equation, the tubular reactor achieved a conversion rate of approximately 63.21%.

In the case of two stirred reactors with a volume of 1 L each, the conversion rate in each reactor was calculated using the same equation. Since the reactors operate independently, the conversion rate in the second reactor is assumed to be the same as in the first reactor. The overall conversion rate in the two stirred reactors was obtained by multiplying the individual conversion rates, resulting in a decrease to around 43.23%.

The change in performance can be attributed to the altered reactor configuration. The tubular continuous reactor provides a longer residence time for the slurry, allowing for a higher conversion rate. On the other hand, the two stirred reactors split the slurry into smaller volumes, reducing the residence time and consequently leading to a lower overall conversion rate. This highlights the importance of reactor design and its impact on the performance of bio-oil production systems.

Learn more about continuous reactor here:

https://brainly.com/question/31518645

#SPJ11

Calculation of area of the region. The area of the region can be calculated as shown below; We know that the density of potential subscribers is 1000 per square kilometer.

The total number of potential subscribers in the region is given by total number of potential subscribers = density x area of the region we can also obtain the total number of potential subscribers from the given number of base stations as shown below; Total number of potential.

Since the hexagon is a regular polygon, its area is equal to times the area of the equilateral triangle. Therefore, the area of the hexagon is  times the area of the equilateral triangle. Using the formula for the side length of the hexagon, the area can be calculated as shown.

To know more about  potential visit:

https://brainly.com/question/28300184

#SPJ11

a)Principal = Cassegrain reflector antenna, This off-axis arrangement is what makes it an offset-fed antenna. b) Increasing the Size, Surface Accuracy c)Phased array antennas consist of multiple individual antenna elements, each with its own phase shifter

(a) Offset-fed Cassegrain Reflector Antenna:

A typical configuration of an offset-fed Cassegrain reflector antenna consists of a primary reflector (larger parabolic dish) and a secondary reflector (smaller hyperbolic dish). The primary reflector is concave and reflects the incoming signals towards the secondary reflector. The secondary reflector is convex and reflects the signals towards the feed horn located off-center on the primary reflector. This off-axis arrangement is what makes it an offset-fed antenna.

The working principle of an offset-fed Cassegrain reflector antenna involves the incoming signals being focused by the primary reflector onto the secondary reflector. The secondary reflector then redirects the signals towards the feed horn. The offset arrangement helps reduce blockage of the incoming signals by the feed structure, resulting in improved performance and reduced interference. This configuration allows for high antenna efficiency, low spillover losses, and a compact design.

(b) Techniques for Achieving High Gain in Reflector Antennas:

1. Increasing the Size: One way to achieve high gain is by increasing the size of the reflector antenna. Larger reflector dimensions result in a narrower beamwidth and higher directivity, leading to increased gain.

2. Using a Higher Operating Frequency: Operating at higher frequencies allows for smaller wavelength, which enables the use of smaller reflectors with higher curvature and more accurate shaping. This results in higher gain for the antenna.

3. Surface Accuracy: Ensuring a highly accurate surface shape of the reflector is crucial for achieving high gain. Precise manufacturing and installation techniques are employed to minimize surface distortions and imperfections, which can cause signal scattering and decrease the antenna's gain.

(c) Phased Array Antennas:

Phased array antennas consist of multiple individual antenna elements, each with its own phase shifter. By controlling the phase and amplitude of the signals applied to each element, the antenna can steer the main beam electronically without physically moving the antenna.

The operating principle of a phased array antenna involves adjusting the phase shift of the signals across the array elements to create constructive interference in the desired direction and destructive interference in unwanted directions.

By changing the phase relationships, the main beam can be electronically scanned to track satellites or communicate with multiple targets simultaneously.

Advantages of phased array antennas compared to reflector antennas include their ability to rapidly steer the beam, perform beamforming, and adapt to changing communication requirements.

They offer faster response times, greater flexibility, and the potential for multiple beam formation and beam shaping. Additionally, phased array antennas are typically more compact and lightweight compared to large reflector antennas, making them suitable for mobile satellite communications.

Learn more about communications here: https://brainly.com/question/14391635

#SPJ11

The range of K that makes the system stable is 0 < K < 168.64.

Root Locus (RL) is a method that helps to identify the stability of the system. It does so by examining the movement of poles in the s-plane as the gain is varied. For the system with a unity feedback and forward transfer function G(s) = K (s + 2)(s + 4)(s +6), let us sketch RL and find the range of K that makes the system stable.To find the poles of the system, we set the denominator of G(s) equal to zero. That is,(s + 2)(s + 4)(s + 6) = 0Solving for s, we get: s = -2, -4, -6The poles of the system are located at s = -2, s = -4, and s = -6.Now, let us sketch RL for the system.

Step 1: Sketch the real axis and mark the locations of the poles.

Step 2: Determine the RL branches and plot them. To do this, we consider the angle criterion and the magnitude criterion of the RL. The angle criterion states that the roots move along a straight line as the gain K varies. The magnitude criterion states that the roots move towards the open-loop zeros and away from the open-loop poles. Hence, we plot RL as shown below:

Step 3: Identify the regions of the s-plane where the RL intersects the imaginary axis (s=jω). In these regions, the roots are purely imaginary. The corresponding values of K are called the breakaway and re-entry gains, respectively. For the given system, we can see that the RL intersects the imaginary axis between s = -4 and s = -6. Hence, there are two regions of the s-plane where the roots are purely imaginary. These regions correspond to the breakaway and re-entry points of the RL.

Step 4: Find the range of K that makes the system stable. For stability, the RL must lie on the left-hand side of the imaginary axis. The range of K that makes the system stable is therefore 0 < K < 168.64 (approximately). This range corresponds to the region of the RL that is to the left of the intersection point between the RL and the imaginary axis at s = -4.82 (approximately). Note that if K is outside this range, the system is unstable.

Therefore, the range of K that makes the system stable is 0 < K < 168.64.

Learn more about Corresponding values here,Three values of x are in the table. What are the corresponding values of y so that each ordered pair is a solution of th...

https://brainly.com/question/30869622

#SPJ11

The average value of x[n] is given by: μ = (1/N) * ∑(n=0 to N-1) x[n] Substituting the given values, we get:

μ = (1/8) * [3 + (4 + 5j) + (-4 - 3j) + (1 + 5j) - 4 + (1 - 5j) + (-4 + 3j) + (4 - 5j)]

μ = 0

Therefore, the average value of x[n] is 0.

The signal power of x[n] is given by:

P = (1/N) * ∑(n=0 to N-1) |x[n]|^2

Substituting the given values, we get:

P = (1/8) * [|3|^2 + |4 + 5j|^2 + |-4 - 3j|^2 + |1 + 5j|^2 + |-4|^2 + |1 - 5j|^2 + |-4 + 3j|^2 + |4 - 5j|^2]

P = (1/8) * [9 + 41 + 25 + 26 + 16 + 26 + 25 + 41]

P = 20

Therefore, the signal power of x[n] is 20.

A signal x[n] is even if x[n] = x[-n] for all n. A signal is odd if x[n] = -x[-n] for all n. Otherwise, the signal is neither even nor odd.

To determine if x[n] is even, we check whether x[n] is equal to x[-n] for all n. Substituting the given values, we get:

x[0] = 3

x[1] = 4 + 5j

x[2] = -4 - 3j

x[3] = 1 + 5j

x[4] = -4

x[5] = 1 - 5j

x[6] = -4 + 3j

x[7] = 4 - 5j

x[-1] = 4 - 5j

x[-2] = -4 + 3j

x[-3] = 1 - 5j

x[-4] = -4

x[-5] = 1 + 5j

x[-6] = -4 - 3j

x[-7] = 4 + 5j

Therefore, x[n] ≠ x[-n] for all n, which means that x[n] is neither even nor odd.

The average value of x[n] is 0 and the signal power of x[n] is 20. The signal x[n] is neither even nor odd.

To know more about  average value, visit:

https://brainly.com/question/130657

#SPJ11

Arithmetic:(i) 1, (ii) 1.5,(iii)1.5. Statements: (i) total=0; -Assignment, (ii) student++; -Increment, (iii) System.out.println Output: (i)"1+2=" "1+2=12",(ii) "1+2=""1+2=3",(iii) 1+2+"abc""3abc". Define array: int totalScore =new int[30];

Arithmetic operations:

(i) 3/2 = 1 (integer division)

(ii) 3.0/2 = 1.5 (floating-point division)

(iii) 3/2.0 = 1.5 (floating-point division)

Type of statements:

(i) total = 0; - Assignment statement

(ii) student++; - Increment statement

(iii) System.out.println("Pass"); - Method invocation statement

Output of statements:

(i) System.out.println("1+2="+1+2); - Output: "1+2=12" (concatenation happens from left to right)

(ii) System.out.println("1+2=" +(1+2)); - Output: "1+2=3" (parentheses force addition before concatenation)

(iii) System.out.println(1+2+"abc"); - Output: "3abc" (addition is performed first, then concatenation)

Defining an array in the code: int totalScore = new int[30];

In this line of code, an array named "totalScore" is defined. The array has a length of 30 elements, indicated by the number 30 in square brackets [ ]. The type of elements in the array is int, as specified by the keyword "int" before the variable name.

The keyword "new" is used to create a new instance of the array with the specified length. The variable "totalScore" is then assigned the reference to the newly created array. This line of code declares and initializes an integer array named "totalScore" with a length of 30.

Learn more about array here:

https://brainly.com/question/31966920

#SPJ11

The redox reaction among the given options is: OCH4(g) + 2 O2(g) → CO2(g) + 2 H2O(g). In this reaction, methane (CH4) is oxidized to carbon dioxide (CO2), and oxygen (O2) is reduced to water (H2O).

Among the given options, the redox reaction is represented by OCH4(g) + 2 O2(g) → CO2(g) + 2 H2O(g). This reaction involves the oxidation and reduction of different species.

In the reaction, methane (CH4) is oxidized to carbon dioxide (CO2). Methane is a hydrocarbon with carbon in the -4 oxidation state, and in the product CO2, carbon is in the +4 oxidation state. This indicates that carbon in methane has lost electrons and undergone oxidation.

On the other hand, oxygen (O2) is reduced to water (H2O). In the reactant O2, oxygen is in the 0 oxidation state, and in the product H2O, oxygen is in the -2 oxidation state. This implies that oxygen in O2 has gained electrons and experienced reduction.

Overall, the reaction involves the transfer of electrons from methane to oxygen, resulting in the oxidation of methane and the reduction of oxygen. Hence, it is a redox (reduction-oxidation) reaction.

learn more about redox reaction here:

https://brainly.com/question/28300253

#SPJ11

(a) Periodicity: A signal ƒ(t) is periodic with fundamental period T if [tex]f(t + T) = f(t)[/tex] for all t in the domain of

[tex]f(t) = \cos(\pi t) + \sin(t) + \sqrt{3} \cos(2 \pi t)[/tex] In order to determine the period of the signal, we need to find the smallest period of cos(™), sin(t), and cos(2πt).cos(™) has a period of 2π.Sin(t) has a period of 2π.cos(2πt) has a period of 1/2π = 0.5.

So, the period of the signal ƒ(t) is the LCM of the periods of the three component signals. Here, the LCM of 2π, 2π, and 0.5 is 4π.Therefore, ƒ(t) is periodic with a fundamental period of 4π. (ii) h(t) = 4 + sin(wt) The function h(t) is not periodic because it does not repeat over any interval.

(b) The probability that a 0 was transmitted if a 0 is received is P(0 was transmitted and 0 was received) / P(0 was received).The probability that a 0 was transmitted and 0 was received is P(0 was transmitted) × P(0 was received given that 0 was transmitted) = 0.8 × 0.9 = 0.72.The probability that a 0 was received is P(0 was transmitted and 0 was received) + P(1 was transmitted and 1 was received)

= (0.8 × 0.9) + (0.2 × 0.7) = 0.86.

Therefore, the conditional probability that a 0 was transmitted if a 0 is received is P(0 was transmitted and 0 was received) / P(0 was received) = 0.72 / 0.86 = 0.8372 (to 4 significant figures).Similarly, the probability that a 1 was transmitted if a 1 is received is P(1 was transmitted and 1 was received) / P(1 was received). The probability that a 1 was transmitted and 1 was received is P(1 was transmitted) × P(1 was received given that 1 was transmitted) = 0.2 × 0.7 = 0.14.The probability that a 1 was received is P(0 was transmitted and 0 was received) + P(1 was transmitted and 1 was received)

= (0.8 × 0.9) + (0.2 × 0.7)

= 0.86.

Therefore, the conditional probability that a 1 was transmitted if a 1 is received is P(1 was transmitted and 1 was received) / P(1 was received) = 0.14 / 0.86 = 0.1628 (to 4 significant figures).

To know more about period of the signal visit:

https://brainly.com/question/17417288

#SPJ11