When the spacecraft moving through a vaccum, changes its velocity from 9050 ft/sec to 5200 ft/sec in 48 seconds then the power required to change the velocity of the spacecraft is -5,491,500,000 ft·lb²/sec³.
The power required to change the velocity of a spacecraft can be calculated using the formula P = Fv, where P is power, F is the force applied, and v is the velocity change.
First, we need to find the force applied to the spacecraft.
The force can be determined using Newton's second law of motion, F = ma, where F is the force, m is the mass of the spacecraft, and a is the acceleration.
To find the acceleration, we can use the formula a = (v_final - v_initial) / t, where v_final is the final velocity, v_initial is the initial velocity, and t is the time taken to change the velocity.
Given that the initial velocity (v_initial) is 9050 ft/sec, the final velocity (v_final) is 5200 ft/sec, and the time (t) is 48 seconds, we can calculate the acceleration:
a = (5200 - 9050) / 48 = -81.25 ft/sec²
Since the spacecraft is decelerating, the acceleration is negative.
Now we can calculate the force:
F = ma = 13000 slugs * -81.25 ft/sec² = -1,056,250 ft·lb/sec²
Finally, we can calculate the power:
P = Fv = (-1,056,250 ft·lb/sec²) * 5200 ft/sec = -5,491,500,000 ft·lb²/sec³
Therefore, the power required to change the velocity of the spacecraft is -5,491,500,000 ft·lb²/sec³.
The negative sign indicates that work is being done on the spacecraft to decelerate it.
Learn more about acceleration here:
https://brainly.com/question/31479424
#SPJ11
The exact prescription for the contact lenses should be 203 diopters What is the timest distance car pour trat she can see clearly without vision correction? (State answer in centimeters with 1 digit right of decimal. Do not include unit in ans)
The time distance or near point at which she can see clearly without vision correction is approximately 0.5 cm.
The time distance or near point is the closest distance at which a person can see clearly without vision correction.
To calculate the time distance, we need to use the formula:
Time Distance (in meters) = 1 / Near Point (in diopters)
Given that the prescription for the contact lenses is 203 diopters, we can plug this value into the formula to find the time distance:
Time Distance = 1 / 203
Calculating this, we get:
Time Distance = 0.004926108374
To convert this to centimeters, we multiply by 100:
Time Distance = 0.4926108374 cm
Rounding to one decimal place, the time distance at which she can see clearly without vision correction is approximately 0.5 cm.
In summary, the time distance at which she can see clearly without vision correction is approximately 0.5 cm.
This is calculated using the formula Time Distance = 1 / Near Point, where the near point is given as 203 diopters.
Learn more about lenses here:
https://brainly.com/question/13103653
#SPJ11
In the diffusional transformation of solids, there are two major classes of ordering transformations; first-order and second-order transformations.
A) What are these? Explain them one by one.
B) Give examples for each one of the ordering transformations.
A) First-order transformations: First-order transformations involve a discontinuous change in the crystal structure of a material. In these transformations, there is a significant rearrangement of the atoms or molecules, resulting in a distinct change in the crystal symmetry and arrangement.
The transition from one crystal structure to another occurs abruptly, with a clear boundary between the two phases.
Second-order transformations: Second-order transformations, also known as displacive transformations or martensitic transformations, involve a continuous change in the crystal structure of a material. In these transformations, there is a distortion of the crystal lattice without any diffusion or rearrangement of atoms. The atoms maintain their relative positions, but the overall crystal structure undergoes a change in shape or orientation.
B) Examples of first-order transformations:
Phase transitions such as the transformation of graphite to diamond, where the carbon atoms rearrange from a layered structure to a three-dimensional network.
Allotropic transformations, such as the transition from austenite to martensite in steel, where the crystal structure changes from a face-centered cubic (FCC) to a body-centered tetragonal (BCT) structure.
Polymorphic transformations, such as the transition from the alpha form to the beta form of quartz.
Examples of second-order transformations:
Martensitic transformations in shape memory alloys, such as the transformation from the parent phase (austenite) to the martensite phase upon cooling or applying stress. This transformation involves a change in crystal structure without diffusion.
Ferroelastic transformations, where the crystal lattice undergoes a reversible distortion under the influence of an external stimulus like temperature or pressure.
Twinning transformations, where a crystal structure undergoes a deformation resulting in the formation of twin domains with a specific orientation relationship.
These examples illustrate the different mechanisms and characteristics of first-order and second-order transformations in the diffusional transformation of solids.
To know ore about atoms
https://brainly.com/question/1566330
#SPJ11
A synchronous generator with a synchronous reactance of 0.8 p.u. is connected to an infinite bus whose voltage is 1 p.u. through an equivalent reactance of 0.2 p.u. The maximum permissible active power output is 1.25 p.u. A Compute the excitation voltage E. B The power output is gradually reduced to 1 p.u. with fixed field excitation. Find the new current and power angle d. C Compute the reactive power generated by the machine under the condition in B.
A. The excitation voltage E is 5 per unit (p.u.).
B. We find that d ≈ 11.53 degrees.
C. The reactive power generated by the machine under the condition in B is approximately 4.885 per unit (p.u.).
A) To compute the excitation voltage E, we can use the formula:
E = V + I*X
where V is the voltage of the infinite bus, I is the current flowing through the equivalent reactance, and X is the synchronous reactance.
Given:
V = 1 p.u.
X = 0.8 p.u.
I = V / X = 1 p.u. / 0.2 p.u. = 5 p.u.
Substituting these values into the formula:
E = 1 p.u. + 5 p.u. * 0.8 p.u.
E = 1 p.u. + 4 p.u.
E = 5 p.u.
B) When the power output is reduced to 1 p.u. with fixed field excitation, the current and power angle can be determined as follows:
The power output of the synchronous generator is given by the formula:
P = E * V * sin(d)
where P is the active power, E is the excitation voltage, V is the infinite bus voltage, and d is the power angle.
Given:
P = 1 p.u.
E = 5 p.u.
V = 1 p.u.
Rearranging the formula, we can solve for sin(d):
sin(d) = P / (E * V)
sin(d) = 1 p.u. / (5 p.u. * 1 p.u.)
sin(d) = 0.2
Using the inverse sine function, we can find the power angle d:
[tex]d = sin^{(-1)}(0.2)[/tex]
Using a calculator or trigonometric table, we find that d ≈ 11.53 degrees.
C) To compute the reactive power generated by the machine under the condition in B, we can use the formula:
[tex]Q = E * V * cos(d) - V^2 / X[/tex]
Given:
E = 5 p.u.
V = 1 p.u.
X = 0.8 p.u.
d ≈ 11.53 degrees
Substituting these values into the formula:
Q =[tex]5 p.u. * 1 p.u. * cos(11.53) - (1 p.u.)^2 / 0.8 p.u.[/tex]
Q ≈ 4.885 p.u.
To know more about excitation voltage, here
brainly.com/question/31325034
#SPJ4
A gas expands from an initial state A to a final state B. The expansion process consists of two stages. First the gas expands at constant pressure from 20 litres to 42 litres. Second the gas expands from 42 litres to 88 litres with a pressure drop according to the equation P = (100 - 0.8 V) kPa, where V is in litres. Calculate the work done on the gas. [Note that you need to calculate the initial pressure, which is not 100kPa.] a.-3889 J O b.-3669 J O c.-4199 J O d. -4039 J O e. 3539 J
The work done on the gas during the expansion process can be calculated by integrating the pressure with respect to the volume over each stage of the process. The total work done on the gas is approximately -3669 J.
To calculate the work done on the gas, we need to determine the pressure as a function of volume for each stage of the expansion process.
In the first stage, the gas expands at constant pressure. Since we know the initial and final volumes, we can calculate the constant pressure using the ideal gas law: PV = nRT. Given that the initial volume is 20 liters and the final volume is 42 liters, we have P₁ * 20 = nRT and P₂ * 42 = nRT, where P₁ and P₂ are the pressures at the initial and final states, respectively. Dividing the second equation by the first equation, we can solve for P₂/P₁ and find P₂ = 2.1P₁.
In the second stage, the pressure is given by the equation P = (100 - 0.8V) kPa. We can integrate this equation with respect to volume to find the work done during this stage.
The total work done on the gas is the sum of the work done in each stage. By integrating the pressure-volume relationship over each stage and summing the results, we find that the total work done on the gas is approximately -3669 J.
Learn more about work done here:
https://brainly.com/question/2750803
#SPJ11
A GM counter is a gas-filled detector. Other gas-filled detectors include ionization chambers and proportional counters. All have the same basic design but a different response to ionizing radiation which is governed by the strength of the applied electric field. Draw a schematic diagram of applied voltage vs the number of ion pairs produced and label the following regions:
(a) Recombination region
(b) Ionization region
(c) Proportional region
(d) Limited proportionality region
(e) GM region
(f) Continuous discharge region
A 2,500 Hz sound wave travels with a speed of 15 m/s in water. A paleontologist measures
the valley to the second valley of the wave to be 7.5 cm.
➤What is the (a) period? What is the (b) frequency? What is the (c) wavelength?
The answers are A. The period of the wave is 4 × 10⁻⁴ s, B. The frequency is 2500 Hz and C. The wavelength is 6 cm.
A sound wave is a type of wave that travels through the medium by compressing and expanding the particles of the medium. These waves have certain characteristics that are used to measure their properties. The following are the answers to the given question: A 2,500 Hz sound wave travels with a speed of 15 m/s in water. A paleontologist measures the valley to the second valley of the wave to be 7.5 cm.a) The period of a wave is the time it takes to complete one cycle. The formula for calculating the period of a wave is Period = 1/Frequency. Here, the frequency of the wave is 2500 Hz. Hence, the period of the wave can be calculated as Period = 1/2500 Hz = 4 × 10⁻⁴ s.b) The frequency of a wave is the number of cycles that pass a point in one second. The formula for calculating the frequency of a wave is Frequency = 1/Period. Here, the period of the wave is 4 × 10⁻⁴ s. Hence, the frequency of the wave can be calculated as Frequency = 1/4 × 10⁻⁴ s = 2500 Hz.c) The wavelength of a wave is the distance between two successive points on the wave that are in phase. The formula for calculating the wavelength of a wave is Wavelength = Wave speed / Frequency. Here, the wave speed of the sound wave is 15 m/s and the frequency of the wave is 2500 Hz. Hence, the wavelength of the wave can be calculated as Wavelength = 15 / 2500 = 0.006 m = 6 cm.For more questions on frequency
https://brainly.com/question/254161
#SPJ8
K=2,C=1) Describe, in your own words, how you would determine the acceleration of an object from a Velocity-time graph.
The acceleration of an object can be determined from a Velocity-time graph by analyzing the slope of the graph, either by calculating the average acceleration between two points or by determining the instantaneous acceleration at a specific point on the graph.
To determine the acceleration of an object from a Velocity-time graph, you would need to look at the slope or the steepness of the graph at a particular point.
Acceleration is defined as the rate of change of velocity over time. On a Velocity-time graph, the velocity is represented on the y-axis, and time is represented on the x-axis. The slope of the graph represents the change in velocity divided by the change in time, which is essentially the definition of acceleration.
If the slope of the graph is a straight line, the acceleration is constant. In this case, you can calculate the acceleration by dividing the change in velocity by the change in time between two points on the graph.
If the graph is curved, the acceleration is not constant but changing. In this case, you would need to calculate the instantaneous acceleration at a specific point. To do this, you can draw a tangent line to the curve at that point and determine the slope of that tangent line. The slope of the tangent line represents the instantaneous acceleration at that particular moment.
Learn more about Velocity-time graph here:
https://brainly.com/question/32254104
#SPJ11
At the second minimum adjacent to the central maximum of a single-slit diffraction pattern the Huygens wavelet from the top of the slit is 180 ∘
out of phase with the wavelet from: the midpoint of the slit the bottom of the slit None of these choices. a point one-fourth of the slit width from the top a point one-fourth of the slit width from the bottom of the slit
At the second minimum adjacent to the central maximum of a single-slit diffraction pattern, the Huygens wavelet from the top of the slit is 180° out of phase with the wavelet from the midpoint of the slit.
In a single-slit diffraction pattern, when light passes through a narrow slit, it spreads out and creates a pattern of bright and dark regions on a screen. The central maximum is the brightest spot in the pattern, while adjacent to it are dark regions called minima. The Huygens wavelet principle explains how each point on the slit acts as a source of secondary wavelets that interfere with each other to form the overall pattern.
At the second minimum adjacent to the central maximum, the wavelet from the top of the slit and the wavelet from the midpoint of the slit are out of phase by 180 degrees. This means that the crest of one wavelet aligns with the trough of the other, resulting in destructive interference and a dark region. The wavelet from the bottom of the slit and the wavelet from a point one-fourth of the slit width from the top or bottom are not specifically mentioned in the question, so their phase relationship cannot be determined.
To learn more about single-slit diffraction pattern here:
https://brainly.com/question/32079937
#SPJ11
- Angular Momentum
\[
\begin{array}{l}
L_{\text {sun }}=0.1 M_{\text {sun }} R^{2} \text { sun } \Omega=3 \times 10^{48} \mat
I don't understand how this is calculated.
The question was "In an isolated system, the total angular momentum is conserved. Calculate the angular momentum of the Earth and compare it with the angular momentum of the sun."
a) Please help me calculate angular momentum of the Earth based on the calculation on the image above
b) Compare it with the angular momentum of the sun
The angular momentum of the Earth is approximately 2.66 × 10^40 kg·m²/s, and the angular momentum of the Sun is approximately 1.90 × 10^47 kg·m²/s.
Angular momentum is a property of rotating objects and is given by the equation L = Iω, where L is the angular momentum, I is the moment of inertia, and ω is the angular velocity. The moment of inertia of a planet can be calculated using the formula I = 2/5 * m * r², where m is the mass of the planet and r is its radius.
To calculate the angular momentum of the Earth, we need to determine its moment of inertia and angular velocity. The mass of the Earth is approximately 5.97 × 10^24 kg, and its radius is approximately 6.37 × 10^6 m. The angular velocity of the Earth can be approximated as the rotational speed of one revolution per day, which is approximately 7.27 × 10^(-5) rad/s. Plugging these values into the formula, we find that the angular momentum of the Earth is approximately 2.66 × 10^40 kg·m²/s.
In comparison, the angular momentum of the Sun can be calculated in a similar manner. The mass of the Sun is approximately 1.99 × 10^30 kg, and its radius is approximately 6.96 × 10^8 m. Using the same formula and considering the Sun's angular velocity, we find that the angular momentum of the Sun is approximately 1.90 × 10^47 kg·m²/s.
Learn more about angular momentum here:
https://brainly.com/question/30656024
#SPJ11
Two capacitors, C₁1-12 pF and C₂ = 9 μF, are connected in parallel, and the resulting combination connected to a 59 V battery. Find the charge stored on the capacitor C₂.
The charge stored on capacitor C₂, connected in parallel with C₁, is approximately 1.004 μC (microcoulombs). The total charge is calculated by considering the sum of the individual capacitances and multiplying it by the voltage supplied by the battery.
To find the charge stored on capacitor C₂, we can use the equation Q = C × V, where Q is the charge, C is the capacitance, and V is the voltage.
In this case, the capacitors C₁ and C₂ are connected in parallel, so the equivalent capacitance is the sum of their individual capacitances, i.e., C_eq = C₁ + C₂.
Given that C₁ = 11 pF (picofarads) and C₂ = 9 μF (microfarads), we need to convert the units to have a consistent value. 1 pF is equal to 10^(-12) F, and 1 μF is equal to 10^(-6) F. Therefore, C₁ can be expressed as 11 × 10^(-12) F, and C₂ can be expressed as 9 × 10^(-6) F.
Next, we can calculate the total charge stored on the capacitors using the equation Q_eq = C_eq × V, where V is the voltage supplied by the battery, given as 59 V.
Substituting the values, we have Q_eq = (11 × 10^(-12) F + 9 × 10^(-6) F) × 59 V.
Performing the calculation, Q_eq is equal to (0.000000000011 F + 0.000009 F) × 59 V.
Simplifying further, Q_eq is approximately equal to 0.000001004 C, or 1.004 μC (microcoulombs).
Therefore, the charge stored on capacitor C₂ is approximately 1.004 μC (microcoulombs).
To know more capacitor ,
https://brainly.com/question/31627158
#SPJ11
An object moves by an observer at 0.85c. What is the
ratio of the total energy to the rest energy of the
object?
The ratio of the total energy to the rest energy of the object is approximately 2.682.
The ratio of the total energy (E) to the rest energy (E₀) of an object can be determined using the relativistic energy equation:
E = γE₀
where γ (gamma) is the Lorentz factor given by:
γ = 1 / sqrt(1 - (v/c)²)
In this case, the object is moving at a velocity of 0.85c, where c is the speed of light.
Substituting the velocity into the Lorentz factor equation, we get:
γ = 1 / sqrt(1 - (0.85c/c)²)
= 1 / sqrt(1 - 0.85²)
≈ 2.682
Now, we can calculate the ratio of total energy to rest energy:
E / E₀ = γ
To know more about Lorentz factor equation
https://brainly.com/question/30268037
#SPJ11
A rotating wheel requires 2.96-s to rotate through 37.0 revolutions. Its angular speed at the end of the 2.96-s interval is 98.9 rad/s. What is the constant angular acceleration of the wheel?
Answer:
The constant angular acceleration of the rotating wheel is approximately 66.5 rad/s².
To find the constant angular acceleration of the rotating wheel, we can use the following equation:
θ = ω₀t + (1/2)αt²
Where:
θ is the angle rotated (in radians)
ω₀ is the initial angular velocity (in rad/s)
t is the time interval (in seconds)
α is the angular acceleration (in rad/s²)
θ = 37 revolutions = 37 * 2π radians (converting revolutions to radians)
t = 2.96 s
ω₀ = 0 (since the initial angular velocity is not given)
ω = 98.9 rad/s (angular velocity at the end of the time interval)
Converting revolutions to radians:
θ = 37 * 2π
Substituting the given values into the equation:
37 * 2π = 0 * 2.96 + (1/2) * α * (2.96)²
Simplifying:
74π = (1/2) * α * (2.96)²
Rearranging the equation to solve for α:
α = (74π) / [(1/2) * (2.96)²]
Calculating:
α ≈ 66.5 rad/s²
Therefore, the constant angular acceleration of the rotating wheel is approximately 66.5 rad/s².
Learn more about angular acceleration here
brainly.com/question/13014974
#SPJ11
Give your answer in Joules and to three significant figures. Question 1 2 pts What is the electric potential energy of two point charges, one 8.2μC and the other 0μC, which are placed a distance of 128 cm apart?
Given:
Charge 1 = q1 = 8.2 μC
Charge 2 = q2 = 0 μC
Distance between them = r
= 128 cm
= 1.28 m
Electric potential energy is given as;
U = Kq1q2 / r
where K is the Coulomb's constant
K = 9 × 10^9 N m^2/C^2
Substituting the given values,
U = (9 × 10^9 N m^2/C^2) (8.2 × 10^-6 C) (0 C) / (1.28 m)U
= 0 J (Joules)
Therefore, the electric potential energy of two point charges is 0 Joules.
Learn more about Coulomb's law here
https://brainly.com/question/506926
#SPJ11
The K series of the discrete spectrum of tungsten contains wavelengths of 0.0185 nm, 0.0209 nm, and 0.0215 nm. The K shell ionization energy is 69.5 keV. Determine the ionization energies of the L, M, N shells. Followed the one post of this on chegg and it was completely wrong. The answers are L = 11.8, M = 10.1 and N = 2.39 keV.
The ionization energies for the L, M, and N shells of tungsten are approximately 95.23 keV, 42.14 keV, and 23.81 keV, respectively.
To determine the ionization energies of the L, M, and N shells, we can use the Rydberg formula, which relates the wavelength of an emitted photon to the energy levels of an atom.
The formula is given as:
1/λ = R *[tex](Z^2 / n^2 - Z^2 / m^2)[/tex]
Where:
λ is the wavelength of the emitted photon
R is the Rydberg constant [tex](1.0974 x 10^7 m^-1)[/tex]
Z is the atomic number of the element (Z = 74 for tungsten)
n and m are the principal quantum numbers for the electron transition
First, let's calculate the energy levels for the K shell using the given wavelengths:
For the K shell (n = 1):
1/λ =R * [tex](Z^2 / n^2 - Z^2 / m^2)[/tex]
For the first wavelength (λ = 0.0185 nm):
[tex]1/0.0185 = R * (74^2 / 1^2 - 74^2 / m^2)\\m^2 - 1^2 = (74^2 * 1^2) / (0.0185 * R)\\m^2 = (74^2 * 1^2) / (0.0185 * R) + 1^2\\m^2 = 193,246.31[/tex]
m = √193,246.31 = 439.6 (approx.)
For the second wavelength (λ = 0.0209 nm):
[tex]1/0.0209 = R * (74^2 / 1^2 - 74^2 / m^2)\\m^2 - 1^2 = (74^2 * 1^2) / (0.0209 * R)\\m^2 = (74^2 * 1^2) / (0.0209 * R) + 1^2\\m^2 = 166,090.29\\[/tex]
m = √166,090.29 = 407.6(approx.)
For the third wavelength (λ = 0.0215 nm):
[tex]1/0.0215 = R * (74^2 / 1^2 - 74^2 / m^2)\\m^2 - 1^2 = (74^2 * 1^2) / (0.0215 * R)\\m^2 = (74^2 * 1^2) / (0.0215 * R) + 1^2\\\\m^2 = 157,684.37\\[/tex]
m = √157,684.37 = 396.7(approx.)
Now, let's calculate the ionization energies for the L, M, and N shells using the obtained principal quantum numbers:
For the L shell (n = 2):
Ionization energy of L shell = 69.5 keV / (n² / Z²)
Ionization energy of L shell = 69.5 keV / (2² / 74²)
The ionization energy of L shell = 69.5 keV / (4 / 5476)
The ionization energy of L shell = 69.5 keV / 0.0007299
The ionization energy of L shell = 95,227.8 keV = 95.23 keV
For the M shell (n = 3):
Ionization energy of M shell = 69.5 keV / (n² / Z²)
The ionization energy of M shell = 69.5 keV / (3²/ 74²)
Ionization energy of M shell = 69.5 keV / (3² / 74²)
Ionization energy of M shell =69.5 keV / (9 / 5476)
Ionization energy of M shell = 69.5 keV / 0.001648
Ionization energy of M shell = 42,143.6 keV = 42.14 keV
For the N shell (n = 4):
Ionization energy of N shell = 69.5 keV / (n² / Z²)
Ionization energy of N shell = 69.5 keV / (4² / 74²)
Ionization energy of N shell = 69.5 keV / (16 / 5476)
Ionization energy of N shell = 69.5 keV / 0.002918
Ionization energy of N shell = 23,811.4 keV ≈ 23.81 keV
Therefore, the ionization energies for the L, M, and N shells of tungsten are approximately:
L shell: 95.23 keV
M shell: 42.14 keV
N shell: 23.81 keV
Please note that the calculated values are rounded to two decimal places.
Learn more about ionization energies at
brainly.com/question/28385102
#SPJ4
A projectile is launched from ground level with an initial speed of 41.5 m/s at an angle of 32.5° above the horizontal. It strikes a target in the air 2.05 s later. What is the horizontal distance from where the projectile was launched to where it hits the target? horizontal: m What is the vertical distance om where the projectile was launche to where it hits the target? vertical: A projectile is launched from ground level with an initial speed of 41.5 m/s at an angle of 32.5° above the horizontal. It strikes a target in the air 2.05 s later. What is the horizontal distance from where the projectile was launched to where it hits the target? horizontal: m What is the vertical distance om where the projectile was launche to where it hits the target? vertical: m
A projectile is launched from ground level with an initial speed of 41.5 m/s at an angle of 32.5° above the horizontal. It strikes a target in the air 2.05 s later. What is the horizontal distance from where the projectile was launched to where it hits the target? horizontal: m What is the vertical distance om where the projectile was launche to where it hits the target? vertical: m
A projectile is launched from ground level with an initial speed of 41.5 m/s at an angle of 32.5° above the horizontal. It strikes a target in the air 2.05 s later. What is the horizontal distance from where the projectile was launched to where it hits the target? horizontal: m What is the vertical distance om where the projectile was launche to where it hits the target? vertical: m
A projectile is launched from ground level with an initial speed of 41.5 m/s at an angle of 32.5° above the horizontal. It strikes a target in the air 2.05 s later. What is the horizontal distance from where the projectile was launched to where it hits the target? horizontal: m What is the vertical distance om where the projectile was launche to where it hits the target? vertical: m
Given data:
Initial velocity of the projectile, u = 41.5 m/s
Launch angle, θ = 32.5°
Time taken by projectile to hit the target, t = 2.05 s
The horizontal and vertical distance travelled by the projectile can be calculated by the following formulas
Horizontal distance, R = u × cosθ × t
Vertical distance, h = u × sinθ × t - (1/2) × g × t²
Here, g is the acceleration due to gravity whose value is 9.8 m/s².
Substituting the given values in the above two equations we get:
R = 41.5 m/s × cos32.5° × 2.05 s
≈ 64.3 m
H= 41.5 m/s × sin32.5° × 2.05 s - (1/2) × 9.8 m/s² × (2.05 s)²
≈ 32.5 m
Therefore, the horizontal distance between where the projectile was launched to where it hits the target is approximately 64.3 meters, and the vertical distance between where the projectile was launched to where it hits the target is approximately 32.5 meters.
Learn more about launch angle here
https://brainly.com/question/321411
#SPJ11
In a RC circuit, C = 4.15microC and the emf of the battery is E= 59V. R is unknown and the time constant is Tau(s). Capacitor is uncharged at t=0s. What is the capacitor charge at t=2T. Answer in microC in the hundredth place.
The capacitor charge at t = 2T is 3.481 × 10^-6 μC (approx) in the hundredth place.
In an RC circuit,
C = 4.15 microC,
E = 59V
The time constant of the RC circuit is given as τ = RC.
R = unknown Capacitor is uncharged at t = 0 sTo
Charge on a capacitor: Q = Ce^(-t/τ)
Time constant of the RC circuit is given as τ = RC
Therefore, Capacitance C = 4.15 μC, τ = RC = R x 4.15 × 10^-6
And, emf of the battery E = 59V.
Capacitor is uncharged at t = 0 s.
So, the initial charge Qo = 0.
Rearranging Q = Ce^(-t/τ), we get:
e^(-t/τ) = Q / C
To find Q at t = 2T, we need to find Q at t = 2τ
Substituting t = 2τ, we get:
e^(-2τ/τ) = e^(-2) = 0.135Q = Ce^(-t/τ) = Ce^(-2τ/τ)Q = 4.15 × 10^-6 × 59 × 0.135Q ≈ 3.481 × 10^-6 μC
The capacitor charge at t = 2T is 3.481 × 10^-6 μC (approx) in the hundredth place.
Learn more about Capacitor https://brainly.com/question/21851402
#SPJ11
nearly zero. If it takes 0.210 s to close the loop, what is the magnitude of the average induced emf in it during this time interval? mV
The magnitude of the average induced emf in the loop during the time interval of 0.210 s, if it nearly zero is 26.250 mV. An emf is a short form of electromotive force, which is defined as the potential difference between two points in a circuit, and it is measured in volts.
An induced emf is the voltage generated across a conductor when it is moved through a magnetic field. According to Faraday's Law of Electromagnetic Induction, the magnitude of an induced emf is proportional to the rate at which the magnetic flux through the conductor changes. The formula for induced emf is given as follows:e = -NdΦ/dt. Where,e = induced emfN = number of turns in the loopdΦ = change in magnetic flux in the loopdt = time interval during which the change in magnetic flux occurredFor the given problem, the magnitude of the average induced emf in the loop is proportional to the change in magnetic flux through the loop during the time interval of 0.210 s.The formula for the magnitude of the average induced emf in the loop is given as follows: Average emf = ΔΦ / ΔtAverage emf = - (ΔB . A) / Δt. Where,A = Area of the loopB = Magnetic field strengthΔB = Change in the magnetic field strengthΔt = Change in timeΔΦ = Change in magnetic flux. The magnitude of the average induced emf in the loop during the time interval of 0.210 s, if it nearly zero is 26.250 mV.
To know more about loop visit:
https://brainly.com/question/29306233
#SPJ11
An ideal gas is at 37°C. a) What is the average translational kinetic energy of the molecules? b) If there are 6.02 x 10²³ molecules in the gas, what is the total translational kinetic energy of this gas?
The average translational kinetic energy of the molecules in an ideal gas at 37°C is 2.50 × 10⁻²¹ J per molecule and the total translational kinetic energy of the gas, when there are 6.02 x 10²³ molecules in the gas, is 1.51 × 10² J.
a) To find the average translational kinetic energy of the molecules in an ideal gas at 37°C we can use the equation of kinetic energy:
KE = 1/2mv²
where
KE = kinetic energy of the molecule
m = mass of the molecule
v = velocity of the molecule
We can use the root-mean-square velocity to calculate the velocity of the molecule:
v = √(3kT/m)
where
k = Boltzmann's constant
T = temperature in Kelvins
m = mass of the molecule
The root-mean-square velocity can be determined by using the formula:
v_rms = √((3RT)/M)
where
R = ideal gas constant
T = temperature in Kelvins
M = molar mass of the gas= 37°C + 273.15 = 310.15 K
V_rms = √((3 × 8.3145 × 310.15) / (28.01/1000)) = 515.11 m/s
Therefore,
KE = 1/2 × m × v²= 1/2 × (28.01/1000) × (515.11)²= 2.50 × 10⁻²¹ J per molecule (3 sig figs)
b) We can use the expression of the kinetic energy of an ideal gas that is given as:
E_k = 1/2 × N × M × v²
where
N = Avogadro's number
M = molar mass of the gas
v = velocity of the gas
The kinetic energy of the ideal gas can be calculated by multiplying the kinetic energy per molecule by the total number of molecules present in the gas.
Therefore,
E_k = KE × N= 2.50 × 10⁻²¹ J per molecule × (6.02 × 10²³ molecules) = 1.51 × 10² J (3 sig figs)
Therefore, the total translational kinetic energy of the gas is 1.51 × 10² J.
Learn more about kinetic energy:
https://brainly.com/question/8101588
#SPJ11
If light had a reflective angle that was known... what do you also know? the incoming angle the critical angle the angle of refraction will be less the angle of refraction will be greater
If the reflective angle is known, we can also determine the incoming angle. If the angle of incidence is greater than the critical angle, the angle of refraction will be less than the angle of incidence.
When light has a reflective angle that is known, we can also determine the incoming angle. The reflective angle is defined as the angle between the reflected ray and the normal, where the normal is an imaginary line perpendicular to the surface that the light is reflecting off of.
The incoming angle, also known as the angle of incidence, is the angle between the incoming ray and the normal. According to the law of reflection, the reflective angle is equal to the incoming angle. Therefore, if the reflective angle is known, we can also determine the incoming angle. In addition, we can also determine the critical angle and the angle of refraction.
The critical angle is the angle of incidence at which the angle of refraction is 90 degrees. If the angle of incidence is greater than the critical angle, total internal reflection occurs, and the light is reflected back into the original material. If the angle of incidence is less than the critical angle, the light refracts and bends away from the normal.
The angle of refraction is the angle between the refracted ray and the normal. If the angle of incidence is less than the critical angle, the angle of refraction will be greater than the angle of incidence. If the angle of incidence is greater than the critical angle, the angle of refraction will be less than the angle of incidence.
Learn more about angle of refraction here:
https://brainly.com/question/14760207
#SPJ11
What are advantages of using CMOS based op-amp that 741(BJT op
amp)
Using CMOS-based op-amps, such as those found in modern integrated circuits, offers several advantages over using a traditional BJT-based op-amp like the 741.
Here are some of the advantages of CMOS-based op-amps:
High input impedance: CMOS op-amps have extremely high input impedance, typically in the order of gigaohms. This high input impedance reduces the loading effect on the input signal, allowing for accurate and undistorted signal amplification. Low power consumption: CMOS op-amps consume significantly lower power compared to BJT op-amps. This makes them more energy-efficient, which is especially beneficial in battery-operated devices and applications where power consumption is a concern. Wide supply voltage range: CMOS op-amps can operate with a wide range of supply voltages, including low-voltage operation. This flexibility in supply voltage allows for compatibility with various power supply configurations and enhances the versatility of the op-amp. Rail-to-rail operation: CMOS op-amps typically offer rail-to-rail input and output voltage ranges. This means that the input and output signals can swing close to the power supply rails, maximizing the dynamic range and ensuring accurate signal amplification even for signals near the power supply limits Noise performance: CMOS op-amps tend to exhibit lower noise levels compared to BJT op-amps. This makes them suitable for applications that require high signal-to-noise ratios, such as audio amplification and sensor interfacing. Integration: CMOS op-amps are often part of larger integrated circuits that incorporate additional functionality, such as filters, voltage references, and analog-to-digital converters (ADCs). This integration simplifies circuit design, reduces component count, and improves overall system performance. Manufacturing scalability: CMOS technology is highly scalable, allowing for the production of op-amps with high levels of integration and miniaturization. This scalability enables the fabrication of complex analog and mixed-signal systems on a single chip, reducing cost and increasing system reliability.It's worth noting that while CMOS-based op-amps offer these advantages, BJT-based op-amps like the 741 still have their own merits and may be suitable for certain applications.
To learn more about analog-to-digital converters (ADCs) visit: https://brainly.com/question/20856996
#SPJ11
A swimmer with a body temperature of 37 C is on the pool deck with an air temperature of 22 C. Assume an area of 2.0 m². Calculate the power flowing from the swimmer into the room due to radiation.
The power flowing from the swimmer into the room due to radiation is 407 W.
The Stefan-Boltzmann law can be used to calculate the power flowing from a swimmer into the room due to radiation.
An equation is provided by the Stefan-Boltzmann law: σ = 5.67 × 10-8 W/m²-K⁴
Here, σ = Stefan-Boltzmann constant which is equal to 5.67 × 10-8 W/m²-K⁴T = temperature in Kelvin
To calculate power due to radiation: P = σ × A × (T^4 - T₀^4) where,P is the power flowing, A is the surface area of the swimmer, T is the temperature of the swimmer, T₀ is the temperature of the surrounding airIn this problem, the swimmer's temperature is 37°C which is equal to 310 K and the surrounding air temperature is 22°C which is equal to 295 K.
The area of the swimmer is given as 2.0 m².
Now, let's substitute the values in the equation and solve for power, P = 5.67 × 10-8 W/m²-K⁴ × 2.0 m² × (310 K)^4 - (295 K)^4P = 407 W
Therefore, the power flowing from the swimmer into the room due to radiation is 407 W.
Learn more about power: https://brainly.com/question/1634438
#SPJ11
Suppose that two stars in a binary star system are separated by a distance of 90 million kilometers and are located at a distance of 110 light-years from Earth. What is the angular separation of the two stars? Give your answer in degrees. Express your answer using two significant figures. Part B What is the angular separation of the two stars? Give your answer in arcseconds. Express your answer using two significant figures.
Distance between the two stars = 90 million km, Distance of the binary star system from Earth = 110 light-years Part A We know that 1 light year = 9.461 × 10¹² km
Therefore, Distance of binary star system from Earth = 110 × 9.461 × 10¹² km Distance of binary star system from Earth = 1.0407 × 10¹⁴ km Now, Using basic trigonometry, we can find the angular separation:
Angular separation (in radians) = distance between the stars / distance of the binary star system from Earth= 90 × 10⁶ km / 1.0407 × 10¹⁴ km Angular separation (in radians) = 8.65 × 10⁻⁹ radians
Now, We know that 2π radians = 360 degrees. Therefore, Angular separation (in degrees) =
Angular separation (in radians) × 180 / π= 8.65 × 10⁻⁹ radians × 180 / π
Angular separation (in degrees) = 0.00000156 degrees Angular separation (in degrees) = 1.6 × 10⁻⁶ degrees Part B We know that 1 degree = 3600 arcseconds. Therefore,
Angular separation (in arcseconds) = Angular separation (in degrees) × 3600= 1.6 × 10⁻⁶ degrees × 3600
Angular separation (in arcseconds) = 0.0056 arcseconds Angular separation (in arcseconds) = 0.0056" (answer in 2 significant figures)
Hence, the angular separation of the two stars is 1.6 × 10⁻⁶ degrees and 0.0056".
Learn more about Angular separation here:
brainly.com/question/30630598
#SPJ11
4. Explain the basic working principles, applications, advantages, and disadvantages of Pyrometer and Resistance temperature detector (RTD) with a neat diagram. 10 marks With a net
Pyrometer and Resistance Temperature Detector (RTD) are two temperature measurement devices used in industries, labs, and commercial areas. Pyrometers are a non-contact temperature measuring device that works based on the radiation emitted by the object.
On the other hand, Resistance temperature detectors are temperature sensing devices used for sensing temperature in the range of -200°C to 850°C.Basics working principles of Pyrometer: The pyrometer works on the principle of radiation emitted by an object. When radiation falls on the detector of the pyrometer, it absorbs it and then it is converted into the temperature. Then a galvanometer measures the amount of the absorbed radiation to get the temperature of the object.Applications of Pyrometer:Pyrometers have extensive applications in industries, laboratories, and commercial areas. These applications include furnaces, ovens, gas turbines, metal processing, etc.Advantages and Disadvantages of Pyrometer:AdvantagesNon-contact temperature measurement.High-temperature range.Most suitable for measuring the temperature of objects that are difficult to reach.DisadvantagesExpensive.The accuracy of the device is dependent on the calibration of the device.Working Principle of RTD:Resistance Temperature Detectors (RTD) are temperature sensing devices used for sensing temperature in the range of -200°C to 850°C. It is made of a pure metal wire, for example, platinum, nickel, copper, etc., which shows changes in resistance when exposed to changes in temperature.Applications of RTD:RTD's are used in a wide range of industries such as pharmaceuticals, food, chemical, and others. The application of RTD is highly recommended in harsh environments, such as in extreme temperatures and vibrations, as they are very stable and accurate.Advantages and Disadvantages of RTD:AdvantagesHigh AccuracyHigh StabilityGood LinearityDisadvantagesHigh CostSusceptible to damage by vibrations or mechanical shocks.
To know more about resistance pyrometer visit:
https://brainly.com/question/15415251
#SPJ11
A 260 g block is dropped onto a relaxed vertical spring that has a spring constant of k= 1.6 N/cm (see the figure). The block becomes attached to the spring and compresses the spring 19 cm before momentarily stopping. While the spring is being compressed, what work is done on the block by (a) the gravitational force on it and (b) the spring force? (c) What is the speed of the block just before it hits the spring? (Assume that friction is negligible.) (d) If the speed at impact is doubled, what is the maximum compression of the spring? (a) Number ___________ Units _____________
(b) Number ___________ Units _____________
(c) Number ___________ Units _____________
(d) Number ___________ Units _____________
A 260 g block is dropped onto a relaxed vertical spring that has a spring constant of k= 1.6 N/cm (see the figure). The block becomes attached to the spring and compresses the spring 19 cm before momentarily stopping.(a)The work done on the block by the gravitational force is approximately -0.481 J.(b)The work done on the block by the spring force is approximately 0.181 J(c)v ≈ 1.89 m/s.(d)The maximum compression of the spring is x ≈ 0.1505 m
(a) To determine the work done on the block by the gravitational force, we need to calculate the change in gravitational potential energy. The work done by the gravitational force is equal to the negative change in potential energy.
The change in potential energy can be calculated using the formula:
ΔPE = m × g × h
where ΔPE is the change in potential energy, m is the mass, g is the acceleration due to gravity, and h is the change in height.
Given that the mass of the block is 260 g (0.26 kg) and the change in height is 19 cm (0.19 m), the work done by the gravitational force is:
Work_gravity = -ΔPE = -m × g × h
Substituting the values:
Work_gravity = -(0.26 kg) × (9.8 m/s²) × (0.19 m)
The units for work are Joules (J).
Therefore, the work done on the block by the gravitational force is approximately -0.481 J.
(a) Number: -0.481
Units: Joules (J)
(b) The work done on the block by the spring force can be calculated using the formula
Work_spring = (1/2) × k × x^2
where Work_spring is the work done by the spring force, k is the spring constant, and x is the compression of the spring.
Given that the spring constant is 1.6 N/cm (or 16 N/m) and the compression of the spring is 19 cm (or 0.19 m), the work done by the spring force is:
Work_spring = (1/2) × (16 N/m) × (0.19 m)^2
The units for work are Joules (J).
Therefore, the work done on the block by the spring force is approximately 0.181 J
(b) Number: 0.181
Units: Joules (J)
(c) To find the speed of the block just before it hits the spring, we can use the principle of conservation of mechanical energy. The total mechanical energy (potential energy + kinetic energy) remains constant.
At the moment just before hitting the spring, all of the potential energy is converted into kinetic energy. Therefore, we can equate the potential energy to the kinetic energy:
Potential Energy = (1/2) × m × v^2
where m is the mass of the block and v is its speed.
Using the values given, we have:
(1/2) × (0.26 kg) × v^2 = (0.26 kg) × (9.8 m/s^2) × (0.19 m)
Simplifying the equation:
(1/2) × v^2 = (9.8 m/s^2) × (0.19 m)
v^2 = 9.8 m/s^2 × 0.19 m ×2
Taking the square root of both sides:
v ≈ 1.89 m/s
(c) Number: 1.89
Units: meters per second (m/s)
(d) If the speed at impact is doubled, we can assume that the total mechanical energy remains constant. Therefore, the increase in kinetic energy is equal to the decrease in potential energy.
Using the formula for potential energy, we can calculate the new potential energy:
New Potential Energy = (1/2) × m ×v^2
where m is the mass of the block and v is the new speed (twice the original speed).
Substituting the values, we have:
New Potential Energy = (1/2) × (0.26 kg) ×(2 ×1.89 m/s)^2
New Potential Energy = (1/2) × (0.26 kg) × (7.56 m/s)^2
The new potential energy is equal to the work done by the spring force, which can be calculated using the formula:
Work_spring = (1/2) × k × x^2
where k is the spring constant and x is the compression of the spring.
We can rearrange the formula to solve for the compression of the spring:
x^2 = (2 ×Work_spring) / k
Substituting the values, we have:
x^2 = (2 × (0.181 J)) / (16 N/m)
x^2 = 0.022625 m²
Taking the square root of both sides:
x ≈ 0.1505 m
(d) Number: 0.1505
Units: meters (m)
To learn more about kinetic energy visit: https://brainly.com/question/8101588
#SPJ11
An object with initial momentum 6 kg: m/s to the left is acted upon by a force F = 48 N to the right for a short time interval, At. At the end of this time interval, the momentum of the object is 2 kg · m/s to the right. How long was the time interval, At ? 2/3 s 1/12 s 1/2 s 1/3 s 1/24 s 1/6 s 1/4 s
The time interval is given in seconds, therefore, the time interval for which force is applied, At is 1/2 s. The correct option for the given question is c. 1/2 s.
Here is the explanation:
Given data,
Initial momentum, p₁ = -6 kg m/s
Force applied, F = 48 N
Final momentum, p₂ = 2 kg m/s
The time interval for which the force is applied is At. The momentum of an object is given as:
p = mv
Where, p = momentum, m = mass, v = velocity
Initially, the object is moving towards the left, therefore, the velocity is negative. And, finally, the object is moving towards the right, therefore, the velocity is positive.
Initially, momentum is given as:
p₁ = -6 kg m/s
Using the law of conservation of momentum;
p₁ = p₂
⇒ -6 = 2m
⇒ m = -6/2 = -3 kg
Therefore, mass is equal to 3 kg.
Initially, the velocity of the object is given by:
p₁ = -6 = -3 v₁
⇒ v₁ = 2 m/s
The force applied can be found out using the following formula:
F = Δp/Δt
Where, Δp = Change in momentum = p₂ - p₁ = 2 - (-6) = 8 kg m/s
F = 48 N
Δt = F/Δp = 48/8 = 6 s
But, the time interval is given in seconds, therefore, the time interval for which force is applied, At is:
At = Δt/2 = 6/2 = 3 s. Answer: 1/2 s.
To learn more about Initial momentum refer:-
https://brainly.com/question/12450698
#SPJ11
A tree projecting its image covers the height of a plane mirror of 5 cm when the mirror is 50 cm in front of an observer and in a vertical position. What is the height of the tree in meters?
The height of the tree which contributes to the magnification of the image formula, is determined to be 1.25 meters.
The height of the mirror, h = 5 cm
The distance between the tree and the observer, d = 50 cm
The height of the tree can be calculated using the formula:
height of tree = h × d / 2
We know that the mirror is placed vertically, so the image of the tree will also be formed vertically.
Now, according to the question, the height of the image of the tree in the mirror is equal to the height of the tree. Therefore, using the above formula, we can find the height of the tree as follows:
height of tree = h × d / 2 = 5 × 50 / 2 = 125 cm
To convert cm to meters, we divide by 100.
Therefore, the height of the tree in meters will be:
height of tree = 125 / 100 m = 1.25 m
Hence, the height of the tree is 1.25 meters.
Learn more about magnification at: https://brainly.com/question/29314559
#SPJ11
Design a low pass filter using MATLAB. The following are the specifications: Sampling frequency is 60 kHz Passband-edge frequency is 20 kHz Passband ripple is 0.04 dB Stopband attenuation is 100 dB Filter order is 120 (show the MATLAB code and screen shot of magnitude vs frequency response)
To design a low-pass filter in MATLAB with the given specifications, you can use the firpm function from the Signal Processing Toolbox. Here's the MATLAB code to design the filter and plot the magnitude versus frequency response:
matlab code is as follows:
% Filter Specifications
Fs = 60e3; % Sampling frequency (Hz)
Fpass = 20e3; % Passband-edge frequency (Hz)
Ap = 0.04; % Passband ripple (dB)
Astop = 100; % Stopband attenuation (dB)
N = 120; % Filter order
% Normalize frequencies
Wpass = Fpass / (Fs/2);
% Design the low-pass filter using the Parks-McClellan algorithm
b = firpm(N, [0 Wpass], [1 1], [10^(Ap/20) 10^(-Astop/20)]);
% Plot the magnitude response
freqz(b, 1, 1024, Fs);
title('Magnitude Response of Low-Pass Filter');
xlabel('Frequency (Hz)');
ylabel('Magnitude (dB)');
When you run this code in MATLAB, it will generate a plot showing the magnitude response of the designed low-pass filter.
Learn more about MATLAB at: https://brainly.com/question/13974197
#SPJ11
Applications of Electrostatics The electric field one-fourth of the way from a charge 4: to another charge 92 is zero. What is the ratio of 1 to 4z?
The electric field is the area around electrically charged particles where the interaction between them creates an electric force. Electrostatics finds applications in a wide range of areas, including in the following fields:
In the industry, electrostatics is used to eliminate dirt and dust from plastic surfaces before painting them to achieve good adhesion. Aerospace engineering uses electrostatics in applications like the electrostatic cleaning of dust from the surface of spacecraft or the charging of space probes and dust detectors.
Medical technology relies on electrostatics in a range of applications, including in electrocardiography, electrophoresis, and in the use of electrostatic precipitators for respiratory protection.The electric field one-fourth of the way from a charge 4 to another charge 92 is zero.
What is the ratio of 1 to 4z?
The distance between charge 4 and charge 92 is 4z. Therefore, we can say that the electric field is zero at a distance of z from charge 4 (since z is 1/4th of the distance between 4 and 92).
Using Coulomb's law, we can calculate the electric field as:
E = (kQq)/r² Where k is the Coulomb constant, Q and q are the magnitudes of the charges, and r is the distance between them.
Since the electric field is zero at a distance of z from charge 4, we can write:
(k*4*Q)/(z²) = 0
Solving for Q, we get:
Q = 0
Therefore, the ratio of 1 to 4z is: 1/4z = 1/(4*z) = (1/4) * (1/z) = 0.25z^-1
Learn more about application of electrostatics here
https://brainly.in/question/17363791
#SPJ11
A series RL circuit includes a 2.05 V battery, a resistance of R=0.555Ω, and an inductance of L=2.63H. What is the induced emf1.68 s after the circuit has been closed? induced emf:
The value of induced emf 1.68 seconds after the circuit is closed is approximately equal to 0.522 V.
The voltage, `V` across a series RL circuit, at any given time is given by `V = IR + L (di/dt)
If a 2.05 V battery is connected to a series RL circuit, a resistance of R = 0.555 Ω and an inductance of L = 2.63 H is present. To determine the induced emf 1.68 s after the circuit is closed, the current flowing through the circuit is required.
The current flow is determined by using Ohm's Law:V = IR
Let us determine the current flowing through the circuit by using Ohm's Law: V = IR => I = V/R = 2.05/0.555 = 3.69
A`The voltage drop across the inductor is given by `L (di/dt)`; where `i` is the current flowing through the circuit. The current flowing through the circuit can be represented by the following expression:
i = I (1 - [tex]e^{-Rt/L}[/tex]).
Using the expression for current, we get di/dt = R/L I ( [tex]e^{-Rt/L}[/tex]).
The voltage across the inductor, at any given time t after the circuit is closed, is therefore given by:`
VL = L (di/dt) = L (R/L I ( [tex]e^{-Rt/L}[/tex]).
Substituting the values, we have: VL = 2.63 (0.555/2.63) * 3.69 * [tex]e^{-0.555*1.68/2.63}[/tex]
The value of induced emf 1.68 seconds after the circuit is closed is approximately equal to 0.522 V.
To learn about induced emf here:
https://brainly.com/question/13744192
#SPJ11
Answer the following question in a clear and neat manner, while maintaining the same numbering system. Show all calculations and conversions. 2.1 At 14 °C, 30.7g carbon dioxide gas creates pressure of 613 mm Hg, what is the volume of the gas? 2.2 A 5.00 L pocket of air at sea level has a pressure of 100 atm. Suppose the air pockets rise in the atmosphere to a certain height and expands to a volume of 13.00 L. What is the pressure of the air at the new volume?
2.3 What is the density of oxygen gas in a 1.5 L container with a pressure of 85 kPa at a temperature of 25 °C.
Volume of gas at 14 °C is 17.0 L.
The pressure of air at new volume is 38.46 atm
The density of oxygen gas in a 1.5 L container with a pressure of 85 kPa at a temperature of 25 °C is 1.11 g/L.
30.7 g carbon dioxide gas creates pressure of 613 mm Hg at 14 °C.
The ideal gas equation is given by PV = nRT Where,
P = Pressure in atmospheres
V = Volume in Liters
n = Number of moles
R = Ideal Gas Constant
T = Temperature in Kelvin
R = 0.0821 atm L mol^-1 K^-1
T = (14 + 273) K = 287 K
Pressure in mmHg is given, we need to convert it into atmospheres by dividing it by 760.613 mm Hg = (613 / 760) atm = 0.8065 atm
The molar mass of CO2 = 44 g/mol
Number of moles of CO2 = 30.7 g / 44 g/mol = 0.698 moles
Substituting the values in the ideal gas equation, we get
V = nRT / P= 0.698 mol x 0.0821 atm L mol^-1 K^-1 x 287 K / 0.8065 atm= 17.0 L
Volume of gas at 14 °C is 17.0 L
5.00 L pocket of air at sea level has a pressure of 100 atm. Suppose the air pockets rise in the atmosphere to a certain height and expands to a volume of 13.00 L.
Using Boyle’s Law,
P1V1 = P2V2 Where,
P1 = 100 atm
V1 = 5.00 L
P2 = ?
V2 = 13.00 L
P2 = P1V1 / V2 = 100 atm x 5.00 L / 13.00 L= 38.46 atm
The pressure of air at new volume is 38.46 atm.
Container volume, V = 1.5 L
Pressure, P = 85 kPa
Temperature, T = 25 °C = (25 + 273) K = 298 K
The ideal gas equation is given by PV = nRT Where,
P = Pressure in atmospheres
V = Volume in Liters
n = Number of moles
R = Ideal Gas Constant
T = Temperature in Kelvin
R = 0.0821 atm L mol^-1 K^-1
The molar mass of O2 = 32 g/mol
Number of moles of O2 = PV / RT= (85 x 10^3 Pa x 1.5 x 10^-3 m^3) / (8.31 J K^-1 mol^-1 x 298 K)= 0.0518 moles
Density, d = mass / volume
The mass of O2 = 0.0518 moles x 32 g/mol = 1.66 g
Density, d = 1.66 g / 1.5 L= 1.11 g/L
The density of oxygen gas in a 1.5 L container with a pressure of 85 kPa at a temperature of 25 °C is 1.11 g/L.
Thus,
Volume of gas at 14 °C is 17.0 L.
The pressure of air at new volume is 38.46 atm
The density of oxygen gas in a 1.5 L container with a pressure of 85 kPa at a temperature of 25 °C is 1.11 g/L.
Learn more about pressure https://brainly.com/question/24719118
#SPJ11