The thrust force that is acting on the rocket engine is obtained as 5782 kN.
What is the thrust?We know that the thrust is the force that is acting on an object that enables the object to be able to move higher. The thrust force can be applied to a rocket such that the rocket can be able to move higher and then pass through the air.
This implies that the thrust force is about the most important force when we want to be able to launch a rocket or when we are trying to move an aeronautical engine. In this case, we are asked to be able to obtain the thrust force as we can see from the parameters that have been given.
We now know that the thrust force can be obtained as; 118kg * 9.8 m/s^2 * 5000m/s = 5782 kN
There would be a thrust of 5782 kN working on the engine.
Learn more about thrust force:https://brainly.com/question/20038629
#SPJ1
in an engine, a piston oscillates with simple harmonic motion so that its position varies according to the expression,
The piston's position is given as x = 4.33 cm, piston's velocity is given as v = -5 cm/s and piston's acceleration a = -17.3 m/s².
Given that, piston oscillates with simple harmonic motion so that its position varies according to the expression x = 5 cos( 2t + π/6 ), where x is in centimetres and t is in seconds.
The equation for piston's position is given as
x = 5 cm cos( 2t + π/6 )
At t = 0, x = 5 cos( π/6 ) = 4.33 cm
To find out piston's velocity, we have to differentiate the equation for position with respect to time.
v = dx/dt = -(10 cm/s) sin(2t + π/6)
At t = 0, v = -5 cm/s
To find out piston's acceleration, we have to differentiate the equation for velocity with respect to time.
a = dv/dt = -(20 cm/s²) cos (2t + π/6)
At t = 0, a = -17.3 cm/s²
To know more about simple harmonic motion:
https://brainly.com/question/18089577
#SPJ4
The steps in the heating of the handle of a pan held over a flame are listed below:
Step 1: Heat from the flame travels to the base of the pan
Step 2: Heat from the base of the pan travels through the pan to the part where the handle touches the pan
Step 3: Heat from one end of the handle travels to the other end
By which method is heat transferred in the three steps?
Radiation in Step 1 and conduction in Steps 2 and 3
Conduction in Step 1 and radiation in Steps 2 and 3
Conduction in Step 1 and convection in Steps 2 and 3
Convection in Step 1 and conduction in Steps 2 and 3
Heat transferred in the three steps is Conduction in Step 1 and radiation in Steps 2 and 3.
Which kind of heat transfer can occur in metals?Conduction. The substance itself does not flow when heat is transported through conduction; instead, heat is internally transferred by the vibrations of atoms and molecules. Metals are typically excellent heat conductors because they can also carry electrons, which can carry heat.
The ability of metal to transfer heatIn contrast to atoms, unbound electrons exist in metals. These electrons are free to roam the metal, interacting with the metal atoms and effectively transferring heat to them through collisions. Due of this, metals are generally superior heat conductors than other types of materials.
To know more about Conduction visit:-
https://brainly.com/question/12136944
#SPJ1
A roller coaster goes over a 12m tall hill then approaches a 30m hill. What is the minimum velocity the roller coaster would need when going over the 12m hill to make it to the top of the 30m hill?
The minimum velocity the roller coaster would need when going over the 12m hill to make it to the top of the 30m hill is 24.25 m/s.
What is the relationship between kinetic energy and potential energy?The relationship between the kinetic energy and potential energy of a body is given by the law of conservation of energy which states that the sum of the energy in a system is conserved.
Hence, the sum of the kinetic energy and the potential energy of a body is given as follows:
Kinetic energy = Potential Energy
Kinetic energy = ¹/₂ mv²
Potential energy = mgh
where;
m is massv is velocityg is the acceleration due to gravityh is the heightAssuming energy is conserved, the energy when going over the top of the 12 m is equal to the energy required to climb the 30 m hill.
¹/₂ mv² = mgh
v = √ 2gh
v = √ 2 * 9.8 * 30
v = 24.25 m/s
Learn more about kinetic and potential energy at: https://brainly.com/question/26882692
#SPJ1
A meridional pattern:A. favors formation of major anticyclones.B. inhibits the formation of major cyclones.C. brings mild weather to most of the country.D. is not typically associated with substantial precipitation.
A meridional pattern favors formation of major anticyclones.
Around a low-pressure area, cyclones are quick inward air circulation. In the Northern and Southern hemispheres, respectively, the air moves counterclockwise and clockwise.Storms that are violent and unfavorable weather frequently accompany cyclones.Cyclos, which in Greek means a snake's coils, is the root of the word cyclone. Henry Paddington came up with the term because tropical storms in the Arabian Sea and Bay of Bengal resemble coiled sea serpents.In order for air to blow outward in the northern hemisphere and in the southern hemisphere, air must circulate from a central area of high pressure towards the periphery.This is how a flowing system becomes circular: blowing winds are redirected from their paths by the Coriolis force to the right in the Northern hemisphere and to the left in the Southern hemisphere.To know about Coriolis force -
https://brainly.com/question/26583295
#SPJ4
The statement by Newton that for every action there is an equal but opposite reaction is which of his laws of motion?
Answer: The third law.
Explanation:
Name four planets which never get above freezing at the equators
Answer:
Mercury, Venus, Earth, Mars
An 3000-kg car traveling at 70 m/s takes 5 m to stop under full braking The same car under similar road conditions, traveling at 140 m/s, takes m to stop under full braking: A) 15 B) 3 C) 10 D) 20 E) 5
It takes 10 minutes to stop.
What happens when brake is applied in car?
To stop the car, force must act in the opposite direction (Newton's First Law). When a car's brakes are applied, the magnitude of the velocity begins to decrease. As a result, the change in velocity is negative, and the acceleration is also negative.
According to the equation,
[tex]v = u + at[/tex]
after applying brake [tex]v = 0[/tex]
[tex]-u = at\\\\a = \frac{-u}{t} \\\\\a = \frac{-70}{5}\\\\a = - 0.234 m/s^2[/tex]
As it is moving at 140m/s
so,
[tex]-u = at\\\\-140 = -0.234 * t\\\\600s = t\\\\t = 10mins[/tex]
It takes 10 minutes to stop.
To know more about car brakes, check out:
https://brainly.com/question/26254970
#SPJ4
the total energy of the twosphere system with earth still external changes as the systemm goes from the confirguration
The supplied statement implies that the system is not being torqued externally.
What kind of energy exist?The six primary forms of energy are biological, galvanic, radiative, muscular, thermal, the nuclear fuel. Other research may focus on other kinds of electrolytic, acoustic, electromagnetic, and others.
Why is energy such a big deal?Despite being a basic human requirement, energy plays a significant role in our daily lives. Energy not only heats but also cools the structures that humans have built. You require energy in order to lift your finger, get out of mattress, or even just walk along the main walkway.
To know more about energy visit:
https://brainly.com/question/1932868
#SPJ4
A ball is projected upward with an initial speed of approximately 30m/s. The diagram at the right represents its position at 1-second intervals of time. At what location will the ball be moving upward with a speed of approximately 10m/s ?
The ball will be moving at a speed of 10m/s when it's at position C.
Using first equation of motion
v=u-at
where
v is final speed
u is initial speed
a is acceleration (here a will be replaced with g as the motion is vertical)
t is time
u = 30m/s
v = 10 m/s
g = -10m/s
By substituting the values ,
10=30 - gr ( taking g as 10)
10t=20
t= 2s
It was given at each position is at the interval of one second each, so the body will be at position C when going upwards at a speed of 10m/s.
To know more about this,
https://brainly.com/question/19390029
LAb motion What do the key results indicate?
Answer:The key results explains how you achieve a certain goal. They have to be quantitative, but always measurable in terms of their progress.
Explanation:
a 120kg elevator is supported by a cable in which the the maximum safe tension is 14000N what is the upward acceleration of the elevator
Important Formulas:
[tex]F=ma[/tex]
Force = mass(measured in kg) * acceleration(measured in m/s^2)
__________________________________________________________
Given:
[tex]m=120kg[/tex]
[tex]F=14,000N[/tex]
[tex]a=?[/tex]
__________________________________________________________
Rearrange formula:
[tex]F=ma[/tex]
[tex]\dfrac{F}{m} =\dfrac{ma}{m}[/tex]
[tex]a=\dfrac{F}{m}[/tex]
__________________________________________________________
[tex]a=\dfrac{14,000}{120}[/tex]
[tex]\fbox{a = 116.67 m/s squared}[/tex]
A 120 kg elevator is supported by a cable in which the maximum safe tension is, 14000 N. The upward acceleration of the elevator is 116. 67 m/s².
What is acceleration?Acceleration is the rate at which the speed and direction of a moving object vary over time. A point or object going straight ahead is accelerated when it accelerates or decelerates.
Even if the speed is constant, motion on a circle accelerates because the direction is always shifting.
This is the formula to calculate the force.
F = ma
we can modify this, a = F/m
Force = mass(measured in kg) x acceleration(measured in m/s²)
Given, mass = 120 kg
Force = 14000 N
Acceleration
Putting the values in the equation
a = F/m
a = 14000 / 120 = 116. 67 m/s²
Therefore, the upward acceleration of the elevator is 116. 67 m/s².
To learn more about acceleration, refer to the link:
https://brainly.com/question/2303856
#SPJ2
On which planet would a measuring instrument placed at the planets equator record the longest time from sunrise to sunset? (1)Mercury (2)Venus (3) Earth (4) Mars
Venus has the longest time from sunrise to sunset, if a measuring instrument is placed at the planet's equator, so option 2 is correct.
What are planets?A planet is a celestial body that revolves around the Sun, has enough mass to overcome rigid body forces and take on a hydrostatic stability shape (nearly round), and has cleared the area in and around its orbit.
The diurnal cycle on Mars is remarkably similar to that on Earth. 24 hours, 37 minutes, and 22 seconds comprise its sidereal day, whereas 24 hours, 39 minutes, and 35 seconds add up to its solar day. Thus, a Martian day (known as "sol") is about 40 minutes longer than an Earthly day.
Venus rotates once every 243 days on Earth. The day on Venus is longer than its orbit.
The smallest and nearest planet to the Sun in the Solar System is Mercury. It is the Sun's planet with the shortest orbital period, taking 87.97 Earth days.
Therefore, Venus has the longest time from sunrise to sunset, if a measuring instrument is placed at the planet's equator.
To know more about planets:
https://brainly.com/question/15268075
#SPJ1
The stars of the milky way are all near a great circle on the celestial sphere. This great circle.
On the celestial sphere, a large circle contains all of the Milky Way's stars. This enormous circle is known as the milky circle. The Milky Way Galaxy is a massive spiral structure with several hundred billion stars, including the sun.
What is the Milky way galaxy?The Milky Way galaxy, which contains our solar system, gets its name from how it appears in the night sky from Earth: a hazy strip of light made up of stars that are too close together to be seen separately.
What are Stars?An astronomical object known as a star is made up of a bright plasma spheroid that is held together by gravity. The Sun is the star that is closest to Earth. Other stars are also visible at night with the unaided eye, but because of their great distances from Earth, they appear as stationary points of light.
Hence, On the celestial sphere, a large circle contains all of the Milky Way's stars. This enormous circle is known as the milky circle. The Milky Way Galaxy is a massive spiral structure with several hundred billion stars, including the sun.
To know more about the milky way galaxy, check out:
https://brainly.com/question/13956361
#SPJ1
3
1 point
Which term is equal to velocity change per second?
gravity
O velocity
O speed
Oacceleration
Answer:
acceleration
hope this helps ;>
Problem-1 A gelatin block with mass 1.00kg is sitting at rest on top of a horizontal surface. The
coefficient of kinetic friction between the block and the surface is 0.70.
A small steel ball with mass 10.9g is moving horizontally directly at the center of the block with a speed
of 853m/s. The ball then collides with the block and gets stuck inside of it.
(a) Assuming that the block stays in one piece, how much of the initial kinetic energy of the ball was
converted into overall (heat + light + sound + material distortions) energy during the collision?
KE = 1/2
KE=
- lov
ми
2
10-9x 853
bo
= 3.9655X 10
The loss of energy in the form of heat, light, sound and material distortions 4014 joule.
What is law of conservation of energy?
Energy cannot be created or destroyed, according to the rule of conservation of energy. However, it is capable of change from one form to another. An isolated system's total energy is constant regardless of the types of energy present.
The law of energy conservation is adhered to by all energy forms. The law of conservation of energy essentially says that all energy is conserved in closed systems, or systems that are isolated from their surroundings.
The kinetic energy of the ball = 1/2×0.0109×863² joule = 4058 joule.
The kinetic energy of the block after the inelastic collision
= 1/2(1 + 0.0109)(0.0109×863/1.0109)² joule.
= 43.77 joule.
Hence, loss of energy in the form of heat, light, sound and material distortions = 4058 joule - 43.77 joule = 4014 joule.
Learn more about energy here:
https://brainly.com/question/1932868
#SPJ1
In the figure, a frictionless roller coaster car of mass m = 826 kg tops the first hill with speed vo = 16.0 m/s at height h = 41.0m. What is the speed of the car (a) point A. (b) point b, and (c) point C? (d) How high will the car go on the last hill, which is too high for it to cross? Use g=9.81 m/s2
The speed of the car at point A is 16 m / s, and the velocity at point B is 24.83 m / s.
What is speed?Speed is the measure of how quickly a moving object changes its distance traveled. It follows that since speed is a scalar, it is a measurement with a magnitude but no direction.
Something that moves quickly and at a high speed, covering a lot of distance quickly. An object moving slowly at a low speed, on the other hand, travels a comparatively short distance in the same amount of time. A thing moving at zero speed doesn't move at all.
Given:
The mass of the car, [tex]m = 826\ kg[/tex],
The initial speed, [tex]u = 16\ m/s[/tex]
(a) The Potential energy [tex](P)[/tex] at point A is the same as the initial because the height of the car is the same.
So, the velocity at point A = 16.0 m/s
(b) Calculate the total energy at the point [tex]E_A = mgh + (1/2)m\times v_A^2 = 833\times 9.81\times 43 + 0.5\times 833\times 16^2[/tex]
[tex]E_A = 432408.39 J[/tex]
And total energy at point [tex]E_B = mgh/2 + (1/2)m\times v(B)^2 = 833\times 9.81\times 43/2 + 0.5\times 833\times v_B^2[/tex] = [tex]E_B =175692.20 + 416.5\times v_B^2[/tex]
Solve the equations,
[tex]432408.39 = 175692.20 + 416.5\times v_B^2[/tex]
[tex]v_B = 24.83 m/s.[/tex]
Therefore, the speed of the car at point A is 16 m / s, and the velocity at point B is 24.83 m / s.
To know more about Speed:
https://brainly.com/question/13074982
#SPJ1
If you know anything about physics please help me i am extremely confused thank you
Each point is at 1-sec time interval, So velocity will be 20 m/s downward at point F.
What is 1st kinematic equation?Kinematics is a branch of classical mechanics that studies the motion of points, objects, and groups of things without addressing the causes of motion. Kinematics is derived from the Greek word "kinesis," which means "motion."
Kinematic equations are a collection of equations that explain an object's motion with constant acceleration. Integrals, rates of change, and derivatives must be understood in order to solve kinematics problems.
Given that Initial speed of ball = V₁= 30 m/s at point A
Now V₂ = -20 m/s [(-)ve sign since final velocity is downward]
a = acceleration due to gravity = - 10 m/s², So
Using 1st kinematic equation:
V₂ = V₁ + a × t
t = (V₂ - V₁)/a
t = [(-20) -30] / (-10) = 5 sec
So velocity of ball will be 20 m/s in downward direction after 5 sec.
Since each point is at 1-sec time interval, So velocity will be 20 m/s downward at point F.
To know more about velocity refer to:
https://brainly.com/question/80295
#SPJ1
a rc circuit is consutructed with a (intiialy uncharged) 5 uf capactiro and a 5-ohm resistor which are connected in series to an ideal battery with emf 60
a rc circuit is constructed with a (initially uncharged) 5 uf capacitor and a 5-ohm resistor which are connected in series to an ideal battery with emf 60 is Q = CV = 9.5 x 10^-6 x 70 = 6.65 x 10^-4 C
What is constructed?
To create something by combining or arranging various pieces or components: the act of building a bridge. also: invent and contrive. put together a plan. to create a drawing of a geometrical figure using the appropriate tools and under the required circumstances
a) time constant = RC = 16.5 x 10^3 x 9.5 x 10^-6 = 0.157 s
b) V = V0 ( 1- e ^ -(t/RC))
after very long time,
V = V0 = e = 105 V
c) Q = CV = 9.5 x 10^-6 x 105 = 9.97 x 10^-4 C
d) I = I0 ( e^(-t/RC))
I0 = e/R = 105/16.5x10^3 = 6.36 mA
after very long time I = 0
e) I0/3 = I0 ( e^-t/RC)
e^-t/RC = (1/3)
-t/RC = ln(1/3)
t = 1.10 x RC = 0.172 sec
f)) V = 105( 1 - e^(-t/RC))
V = 105 ( 1 - e^(-(0.172/0.157)) )
V = 70 V
Q = CV = 9.5 x 10^-6 x 70 = 6.65 x 10^-4 C
To learn more about circumstances visit
https://brainly.com/question/24180186
#SPJ4
5. Which of the following correctly describes the above situation?
6. The final velocity of the two cars after they hit and stick together is:
In this case, the magnitude of the momentum of vehicle 2 is greater than the vehicle 1.
What is momentum?
In Newtonian mechanics, an object's mass and velocity are combined to form momentum, more precisely linear momentum or translational momentum. It has both a magnitude and a direction, making it a vector quantity.
The kilogramme metre per second (kg m/s), or newton-second in the International System of Units (SI), is the unit used to measure momentum.
The rate of change of a body's momentum is equal to the net force exerted on it, according to Newton's second law of motion. Although momentum varies depending on the frame of reference, it is a conserved quantity in any inertial frame, which means that if a closed system is not impacted by outside forces.
To learn more about momentum:
https://brainly.com/question/15460796
#SP J4
Pls help me rapidly is of physical science:
Nitrogen belong to the group 15/5a period 3. It is also Known as pnictogen family .
The pnictogen family—what is it?Any chemical element in group 15 of the periodic table is a pnictogen. Group 15 is often referred to as the nitrogen family or group. Nitrogen, phosphorus, arsenic, antimony, bismuth, and moscovium make up group 15.
What is Periods ?A row of chemical elements makes up a period in the periodic table.
What is groups?In the periodic chart of chemical elements, a group is a column of elements.
Learn more about Pnictogen here: https://brainly.com/question/20373471
#SPJ1
At a distance r from a charge e on a particle of mass m the electric field value is
At a distance r from a charge e on a particle of mass m the electric field value is 8.9876 × 10⁹ N·m²/C². Divide the magnitude of the charge by the square of the distance of the charge from the point. Multiply the value from step 1 with Coulomb's constant.
what is magnitude ?Magnitude can be defined as the maximum extent of size and the direction of an object.
It is used as a common factor in vector and scalar quantities, as we know scalar quantities are those quantities that have magnitude only and vector quantities are those quantities have both magnitude and direction.
There are different ways where magnitude is used Magnitude of earthquake, charge on an electron, force, displacement, Magnitude of gravitational force
For more details regarding magnitude, visit
https://brainly.com/question/28242822
#SPJ1
can somebody help me i want to do my homework please
The difference between the two plot is shown clearly by the distance between the two waves.
What is wave?Wave is defined as a disruption in an energy-conducting medium without a net movement of particles. Wind is the most frequent cause of waves. Wind-driven waves, sometimes referred to as surface waves, are created by friction between the wind and the water's surface.
The two difference between the two plot are the first is the difference between the distance of two crust and trough between the wave in the plot. The second difference is that the first plot is between displacement and distance from the source and the second graph is plot between displacement and time.
Thus, the difference between the two plot is shown clearly by the distance between the two waves.
To learn more about wave, refer to the link below:
https://brainly.com/question/3639648
#SPJ1
What net force would be required to accelerate a 5 Kg object 2 m/s2? [show all work, including the
equation, substitutions with units, and answer with units]
Answer:
10 Newtons.
Explanation:
F=MA
F=(5kg)(2 m/s^2)
10 N
access flooring systems typically consists of modular floor panels that rest on stringers or pedestals. panel sizes typically range from ____ to 24 inches square.
Modular floor panels that rest on pedestals or stringers make up most access flooring systems. Typically, panel dimensions start at 24 by 24 inches square with same distance.
Their dimensions are constant; a raised floor panel is typically 600 mm by 600 mm. A standard access flooring panel in the USA is slightly larger, measuring 24" x 24". (around 610mm). A brand-new and cutting-edge patented solution that comprises of a polished concrete floor panel system that is intended to be put on to a new or retrofit building project is available. The imperfections and traits of a normal polished concrete floor are evident in this appealing, authentic concrete surface. The longest dimension of an object in geometric terms is its distance. International System of Quantities.
Learn more about distance here
https://brainly.com/question/14393400
#SPJ4
What is true about the foci of a planet in elliptical orbit?
A:The sun is located at one focus.
B: Earth is located at one focus.
C: Earth is located in the center of the orbit.
D: The sun is located in the center of the orbit
Statement A. The sun is located at one focus is true about the foci of a planet in an elliptical orbit (option A).
What is an elliptical orbit?An elliptical orbit can be defined as any movement of a celestial body in which the attained object (for example a planet around its star) moves in an eccentric manner or oval-shaped way, which is a feature of the planets in the solar systems including the Earth planet.
The movement of a planet in an elliptical orbit is called an ellipse, while two points that are selected chosen at the start site are known as foci in such orbits.
Therefore, with this data, we can see that an elliptical orbit is an excentric movement of a celestial body such as the earth's planet around the sun, and foci are called to fixed points located inside this orbit.
Learn more about elliptical orbits here:
https://brainly.com/question/29681138
#SPJ1
A crate is pulled to the right with a force of 71.6 N, to the left with a force of 228.2 N, upward with a force of 457.7 N, and downward with a force of 232 N.
Pt 1: What is the net external force in the x direction? Answer in units of N.
Pt 2: What is the net external force in the y direction? Answer in units of N.
Pt 3: What is the magnitude of the net external force on the crate?
Pt 4: What is the direction of the net external force on the crate (as an angle between −180◦ and 180◦, measured from the positive x-axis with counterclockwise positive)?
Answer: (see answers below)
Explanation:
Fnet x = 71.6 - 228.2 = -156.6 N (left)
Fnet y = 457.7 - 232 = 225.7 N (up)
R = [tex]\sqrt{-156.6^{2} + 225.7^{2} }[/tex] = [tex]\sqrt{75464}[/tex] = 274.7 N
Angle of R = 180 - (tan-1)[tex]\frac{225.7}{156.6}[/tex] = 180 - 55.2 = 124.8°
assume that a rod-drawing operation can be carried out either in one pass or in two passes in tandem. if all die angles are the same and the total reduction is the same, will the drawing forces be different?
The drawing forces will be the same because the drawing process can be thought of as a series of incremental reductions taking place in a single die.
What is the draw force of a rod?The pull on the exit section and the friction forces acting along the tube-mandrel interface transmit draw force to the metal. The drawing forces will be the same unless the surface of the rod changes due to external effects such as the environment or additional lubrication while it is between the two dies. There is also increased reduction on a single die.
Ideally, a die can cut into several segments and make it a tandem process. Also, in a tandem operation, the front tension of one segment becomes the back tension of another.
Learn more on drawing force here: https://brainly.com/question/15111829
#SPJ1
Which equation can be used to solve for acceleration?
0 ₁ = AV
a
O vf = at-vi
0 a = 4/1/20
d
O AV =
The best choice is A. The formula that can be used to calculate the acceleration is a= dv/t
The alteration in a body's velocity with respect to time is referred to as acceleration. Using mathematics, t= dv/awhere: dv is the velocity changeThe amount of time usedMaking the formula's subject the time "t": a =dv/tConsequently, t=dv/a is how the equation that can be utilized to solve the acceleration is written.Acceleration: the rate at which the speed and direction of a moving object vary over time. A point or object going straight ahead is accelerated when it accelerates or decelerates. Even if the speed is constant, motion on a circle accelerates because the direction is always shifting.For more information on acceleration kindly visit to
https://brainly.com/question/3046924
#SPJ1
if a magnitude of frequency of simple pendulum on Earth surface was(0.263Hz) What is the period for this pendulum at the same place on Earth surface?
Answer:
The period of a simple pendulum is the time it takes for the pendulum to complete one full swing. This is equal to the reciprocal of the frequency, which means that if the frequency of a simple pendulum is 0.263 Hz, its period would be 1/0.263 = 3.80 seconds. This is the time it would take for the pendulum to swing back and forth once at the same location on the Earth's surface.
Explanation:
A merry-go-round is a playground ride that consists of a large disk mounted to that it can freely rotate in a horizontal plane. The merry-go-round shown is initially at rest, has a radius R = 1.3 meters, and a mass M = 231 kg. A small boy of mass m = 48 kg runs tangentially to the merry-go-round at a speed of v = 2.5 m/s and jumps on.
Required the moment of inertia of the merry go round.
a. I = 12 MR2 is the formula for the merry-go-moment round's of inertia.
I = ½ * 231 * (1.3 * 1.3)
I = 195.195 kgm2
b. The boy's angular speed is specified as = v/R = 2.5/1.3 = 1.92 rad/s.
c. I' = I + mR2 is the formula for the merry-go-moment round's of inertia following the boy's jump on it.
I’ = 195.195 + 48 * (1.3 * 1.3)
I’ = 276.315 kg/m2
The conservation of angular momentum principle determines the merry-go-angular round's speed. As a result, I (0) + m R = 'I' and = (48 * 1.92* 1.3) / 276.315 = 0.433 rad/s
To learn more about conservation of angular momentum.
https://brainly.com/question/29892978
#SPJ1