Answer:
Step-by-step explanation:
Question 2 (35 marks) (a) Find the z-transform of the following sequences: i. {9k +7}=0 ii. {5k + k}K=0 200 [5 Marks]
Z-transform is an important tool in the field of digital signal processing. It is a mathematical technique that helps to convert a time-domain signal into a frequency-domain signal.
It is used to analyze the behavior of linear, time-invariant systems that are described by a set of linear, constant-coefficient differential equations.
Therefore, the z-transform of [tex]{9k +7}=0 is 7/(1-z^-1) + (9z^-1)/((1-z^-1)^2).ii. {5k + k}K=0 200[/tex]The z-transform of the above sequence can be calculated as follows:
Therefore, the z-transform of {5k + k}K=0 200 is 6z^-1 * (1-201z^-201)/(1-z^-1)^2.The above calculations show how to calculate the z-transform of the given sequences.
To know more about important visit:
https://brainly.com/question/31444866
#SPJ11
Problem 1. (16%) Determine the components of the support reaction at the fixed support A of the beam shown. You must include a FBD. 3 kN 0.5 kN/m 5 kN-m A 6 m -3 m-
The components of the support reaction at the fixed support A of the beam are as follows:
1. Vertical component (Ay): 8.5 kN upward
2. Horizontal component (Ax): 3 kN rightward
3. Moment (MA): 51 kN·m counterclockwise
To determine the components of the support reaction, we need to analyze the forces acting on the beam and create a Free Body Diagram (FBD) of the beam.
Given:
- A vertical load of 3 kN at a distance of 6 m from the support.
- A distributed load of 0.5 kN/m along the beam.
- A clockwise moment of 5 kN·m applied at the support.
Step 1: Draw the FBD of the beam.
```
3 kN 0.5 kN/m 5 kN·m
|_____________|_______________|
A | | |
| | |
```
Step 2: Calculate the vertical component (Ay) of the support reaction.
Since there is a vertical load of 3 kN and a distributed load of 0.5 kN/m acting upward, the total vertical force is:
Vertical force = 3 kN + (0.5 kN/m) * 6 m = 6 kN
Therefore, the vertical component of the support reaction at A is 6 kN acting upward.
Step 3: Calculate the horizontal component (Ax) of the support reaction.
There are no horizontal forces acting on the beam, except for the support reaction at A. Hence, the horizontal component of the support reaction is 3 kN acting rightward.
Step 4: Calculate the moment (MA) at the support.
The clockwise moment of 5 kN·m applied at the support needs to be balanced by the counterclockwise moment caused by the support reaction. Let's assume the counterclockwise moment as MA.
To balance the moments:
Clockwise moment = Counterclockwise moment
5 kN·m = MA
Therefore, the moment at the support is 51 kN·m counterclockwise.
Hence, the components of the support reaction at the fixed support A are Ay = 8.5 kN upward, Ax = 3 kN rightward, and MA = 51 kN·m counterclockwise.
Learn more about component:
https://brainly.com/question/28498043
#SPJ11
Please show the process
1. (16 pts) Give a complete and correct name for each of the following molecules. Be sure to indicate stereochemistry where appropriate: (a) (b) (c) (d)
The molecular formula of the molecule is C4H10O. The molecule has an oxygen atom in it, so we can assume that the molecule is an alcohol.
The alcohol has four carbon atoms which suggest that it is butanol. Since there are four carbon atoms, we must determine the position of the hydroxyl group. The alcohol must be placed on the second carbon atom since it is numbered from the end of the carbon chain that is nearest to the hydroxyl group. The complete and correct name of the molecule is 2-butanol.The molecular formula of the molecule is C5H12. The molecule has no functional group in it, so it is an alkane. The alkane has five carbon atoms, and it is named pentane. Since there is no functional group to indicate stereochemistry, we assume that the molecule is a straight-chain pentane. molecule is n-pentane.
The molecular formula of the molecule is C5H10. The molecule has no functional group in it, so it is an alkene. The alkene has five carbon atoms, and it is named pentene. Since there is no functional group to indicate stereochemistry, we assume that the molecule is a straight-chain pentene. The double bond is located between the second and third carbon atoms.
To know more about formula, visit:
https://brainly.com/question/20748250
#SPJ11
How was the Florida International University bridge structurally
supported?
The Florida International University bridge was structurally supported by concrete truss members and diagonal support columns called outrigger columns.
The Florida International University (FIU) bridge, officially known as the FIU-Sweetwater UniversityCity Bridge, was a pedestrian bridge located in Miami, Florida. The bridge, which tragically collapsed on March 15, 2018, during its construction phase, was being built to connect the FIU campus with the neighboring city of Sweetwater. The bridge was intended to provide a safe passage for pedestrians over Southwest Eighth Street.
Structurally, the FIU bridge utilized an innovative design called an "Accelerated Bridge Construction" (ABC) method. This method involved prefabricating the bridge sections off-site and then using a technique known as "self-propelled modular transporters" to move the sections into place. The bridge was designed to be constructed quickly and with minimal disruption to traffic.
The structural support of the FIU bridge relied on several key elements. The main load-bearing components were the bridge's concrete truss members. These trusses were designed to support the weight of the bridge and transfer the loads to the supporting piers located at each end. The trusses were made using a technique called "post-tensioning," which involved reinforcing the concrete with steel cables to increase its strength and stability.
In addition to the truss members, the bridge was also supported by a set of diagonal support columns, known as "outrigger columns," located at various points along the span. These columns were intended to provide additional structural support and increase the bridge's stability.
Unfortunately, the FIU bridge collapsed before it was fully completed, resulting in multiple fatalities and injuries. The exact cause of the collapse was determined to be a combination of design errors, insufficient structural support, and inadequate oversight during the construction process. Following the tragedy, investigations were conducted, and changes were made to improve the safety and oversight of bridge construction projects in the future.
learn more about FIU Bridge Collapse.
brainly.com/question/28848448
#SPJ11
Find two unit vectors orthogonal to both (8, 7, 1) and (-1, 1, 0). (smaller i-value) (larger i-value)
Two unit vectors orthogonal to both (8, 7, 1) and (-1, 1, 0) are (-1, -1, 15)/sqrt(227) and (-1, -1, 15)/sqrt(227).
To find two unit vectors orthogonal (perpendicular) to both (8, 7, 1) and (-1, 1, 0), we can use the cross product of the two given vectors. The cross product of two vectors will yield a vector that is orthogonal to both of them.
Let's calculate the cross product:
(8, 7, 1) × (-1, 1, 0) = [(7 * 0) - (1 * 1), (1 * -1) - (0 * 8), (8 * 1) - (7 * -1)]
= [-1, -1, 15]
Now, to obtain unit vectors, we divide this vector by its magnitude:
Magnitude of [-1, -1, 15] = sqrt((-1)^2 + (-1)^2 + 15^2) = sqrt(1 + 1 + 225) = sqrt(227)
Unit vector 1: (-1, -1, 15) / sqrt(227)
Unit vector 2: (-1, -1, 15) / sqrt(227)
Both of these unit vectors are orthogonal to both (8, 7, 1) and (-1, 1, 0).
To learn more about vectors click here
brainly.com/question/31737683
#SPJ11
Site investigation (S.I) work is critical in understanding ground conditions and determining the impact of proposed structures to be erected on site. Explain what types of SI information you'll need a
By conducting a comprehensive SI, engineers and designers can make informed decisions and implement suitable measures to address any potential challenges or risks associated with the proposed structures.
To gather the necessary information for an SI, the following types of data are typically required:
1. Geological information: This includes the composition and characteristics of the soil and rock formations on the site. This information helps determine the stability of the ground and potential risks such as landslides or sinkholes.
2. Geotechnical data: Geotechnical investigations involve soil and rock testing to assess their strength, density, and permeability. This data is vital for designing foundations and determining the bearing capacity of the ground.
3. Groundwater information: Understanding the groundwater levels and flow patterns is essential for designing drainage systems and preventing water-related issues like flooding or excessive moisture.
4. Environmental data: This includes information about the presence of pollutants, contaminants, or protected species in the area. It helps ensure compliance with environmental regulations and enables appropriate mitigation measures.
5. Archaeological data: If the site has historical significance, an archaeological investigation may be necessary to identify and preserve any cultural artifacts or structures.
By conducting a comprehensive SI, engineers and designers can make informed decisions and implement suitable measures to address any potential challenges or risks associated with the proposed structures.
learn more about engineers from given link
https://brainly.com/question/27158518
#SPJ11
On a coordinate plane, 2 right triangles are shown. The first triangle has points A (negative 1, 3), B (negative 1, 1), C (3, 1). The second triangle has points A prime (2, negative 2), B prime (2, negative 4), C prime (6, negative 4).
Which statements are true about triangle ABC and its translated image, A'B'C'? Select two options.
The rule for the translation can be written as T–5, 3(x, y).
The rule for the translation can be written as T3, –5(x, y).
The rule for the translation can be written as
(x, y) → (x + 3, y – 3).
The rule for the translation can be written as
(x, y) → (x – 3, y – 3).
Triangle ABC has been translated 3 units to the right and 5 units down.
answer: A and E (i think)
A function f is defined as follows: f: Z --> R . Which of the following statements would be true?
a. f is onto if the range of f is the entire set of real numbers. b.f is onto if every integer in Z has an output value c. f is onto if every real number that can be output by this function, can only be output by a single value from the domain. d. f is onto if no integer from z has more than one output.
The correct statement regarding the function f: Z --> R is:
c. f is onto if every real number that can be output by this function, can only be output by a single value from the domain.
To understand why this statement is true, let's break it down step by step:
1. The function f: Z --> R means that the function takes an input from the set of integers (Z) and produces an output in the set of real numbers (R).
2. For a function to be onto, also known as surjective, every element in the codomain (R) must have a corresponding element in the domain (Z) that maps to it.
3. Option a says that f is onto if the range of f is the entire set of real numbers. However, this is not necessarily true. It is possible for the function to only cover a subset of the real numbers and still be onto, as long as every element in that subset has a corresponding element in the domain.
4. Option b states that f is onto if every integer in Z has an output value. This is incorrect because it is possible for a function to only map certain integers to real numbers while still being onto.
5. Option d states that f is onto if no integer from Z has more than one output. This is also incorrect because a function can be onto even if multiple integers map to the same output value, as long as every real number in the codomain has at least one corresponding integer in the domain.
Therefore, option c is the correct statement. It states that f is onto if every real number that can be output by this function can only be output by a single value from the domain. This means that every real number in the codomain has a unique corresponding integer in the domain.
Learn more about Real Number here:
https://brainly.com/question/17019115
#SPJ11
The hydration of this molecule above would lead to two molecules. Which would be the major species? pentane pentan-1-ol pentan-2-ol pentan-1,2-diol propanoic acid and ethanol with heat and an acid catalyst will yield a ether ester amide amine
Hydration is the addition of water to an alkene or alkyne in the presence of a catalyst such as a mineral acid like sulfuric acid. This reaction is a reversible reaction, and in this case, it is an addition reaction. The hydration of pent-1-ene would produce two products pentan-1-ol and pentan-2-ol. Pentan-1-ol would be the major species.
Below is an explanation:The molecule pent-1-ene is an unsaturated hydrocarbon that has a double bond between the first and second carbon atom, as shown in the figure below.When pent-1-ene is hydrated in the presence of an acid catalyst and water, it would produce two molecules, pentan-1-ol, and pentan-2-ol. The reaction would proceed as shown below:The reaction is reversible; hence it can go forward or backward.
However, the forward reaction is more favored than the backward reaction. The major species that would be produced in this reaction is pentan-1-ol.The reaction between propanoic acid and ethanol in the presence of heat and an acid catalyst would lead to the formation of an ester.
The reaction between the two compounds is shown below:Thus, the major product of the reaction between propanoic acid and ethanol in the presence of heat and an acid catalyst is an ester.
For more information on Hydration visit:
brainly.com/question/30373695
#SPJ11
Estimate the boiling temperature at atmospheric pressure 1 atm for acetylene using Van der Waals model with parameters of acetylene a=4.516 L’atm/mol?, b=0.0522 L/mol. Express answer in degrees Celsius.
To estimate the boiling temperature of acetylene at atmospheric pressure (1 atm) using the Van der Waals model, we can use the following formula:
T = (a/((b*R)) - (1/(R*V)))/(ln((V - b)/(V + 2*b))) - (a/(R*V))
Where:
T is the boiling temperature in Kelvin,
a is the Van der Waals constant a (4.516 L’atm/mol in this case),
b is the Van der Waals constant b (0.0522 L/mol in this case),
R is the ideal gas constant (0.0821 L.atm/(mol.K)),
and V is the molar volume of acetylene in liters.
To convert the boiling temperature from Kelvin to Celsius, we can use the formula:
T(°C) = T(K) - 273.15
Let's calculate the boiling temperature of acetylene at 1 atm:
1. Determine the molar volume of acetylene (V):
The molar volume can be calculated using the ideal gas equation:
PV = nRT, where P is the pressure (1 atm), n is the number of moles (1 mol), R is the ideal gas constant (0.0821 L.atm/(mol.K)), and T is the temperature in Kelvin.
Rearranging the equation, we get:
V = nRT/P = (1 mol * 0.0821 L.atm/(mol.K) * T(K))/(1 atm)
Since we are looking for the boiling temperature, let's assume V = 0.1 L (you can choose a different value if you like).
2. Calculate the boiling temperature (T):
Substituting the values into the formula:
T = (4.516 L’atm/mol/((0.0522 L/mol)*(0.0821 L.atm/(mol.K))) - (1/(0.0821 L.atm/(mol.K)*0.1 L)))/(ln((0.1 L - 0.0522 L)/(0.1 L + 2*0.0522 L))) - (4.516 L’atm/mol/(0.0821 L.atm/(mol.K)*0.1 L))
3. Convert the boiling temperature to Celsius:
T(°C) = T(K) - 273.15
Know more about Van der Waals model:
https://brainly.com/question/30820013
#SPJ11
Current Attempt in Progress The designer of a ski resort wishes to have a portion of a beginner's slope on which the snowboarder's speed will remain fairly constant. Tests indicate the average coeffic
The average coefficient of friction should be chosen in such a way that the frictional force between the snowboard and the slope is 1470 N.
the designer of the ski resort wants to create a beginner's slope where the speed of snowboarders remains fairly constant. To achieve this, they need to consider the average coefficient of friction between the snowboard and the slope.
The coefficient of friction is a measure of how much the surface of an object resists sliding against another surface. In this case, it represents the interaction between the snowboard and the slope.
the snowboarder's speed fairly constant, the coefficient of friction should be chosen in such a way that the forces acting on the snowboarder balance each other out. One important force to consider is the force of gravity, which pulls the snowboarder downwards.
the snowboarder has a mass of 150 kg. The force of gravity acting on the snowboarder can be calculated using the formula:
force of gravity = mass x acceleration due to gravity
where the acceleration due to gravity is approximately 9.8 m/s^2.
force of gravity = 150 kg x 9.8 m/s^2 = 1470 N
the snowboarder's speed fairly constant, the frictional force between the snowboard and the slope should be equal in magnitude and opposite in direction to the force of gravity. This will create a balance of forces, resulting in a fairly constant speed.
Therefore, the average coefficient of friction should be chosen in such a way that the frictional force between the snowboard and the slope is 1470 N.
the angle of the slope and the condition of the snow, can also affect the snowboarder's speed. However, the coefficient of friction is a key factor to consider when designing a slope where the speed remains fairly constant.
Learn more about average with the given link,
https://brainly.com/question/130657
#SPJ11
How much heat is released when 50g of steam at 130° is converted into water at 40°C? The specific heats (Cs) of ice, water, and steam are 2.09 J/g.K, 4.184 J/g.K, and 1.96 J/g.K, respectively. For H2O ΔHfus = 6.01 kJ/mol, and ΔHvap = 40.7 kJ/mol.
A.113kJ
B.18.8kJ
C.128.5kJ
D.15.5kJ
The total heat released when 50g of steam at 130°C is converted into water at 40°C is:Q = Q1 + Q2 + Q3= 113kJ + 20.92kJ + 16.59kJ= 150.51kJTherefore, the answer is 128.5kJ (Option C).
Heat released when 50g of steam at 130° is converted into water at 40°C can be calculated using the following steps:Formula for the heat released when steam at 130°C is converted into water at 40°C is:
Q = Q1 + Q2 + Q3Q1
= Heat released when steam at 130°C is converted into water at 100°CQ2
= Heat released when water at 100°C is cooled to 0°CQ3
= Heat released when ice at 0°C is converted into water at 0°CQ1
= m x ΔHvap
= 50g x (40.7 kJ/mol) / (18.02 g/mol)
= 113kJQ2
= m x Cs x ΔT
= 50g x 4.184J/gK x (100 - 0)K
= 20.92kJQ3
= m x ΔHfus
= 50g x (6.01 kJ/mol) / (18.02 g/mol)
= 16.59kJ
Hence, the total heat released when 50g of steam at 130°C is converted into water at 40°C is:Q = Q1 + Q2 + Q3= 113kJ + 20.92kJ + 16.59kJ= 150.51kJTherefore, the answer is 128.5kJ (Option C).
For more information on heat visit:
brainly.com/question/13860901
#SPJ11
Water flows downhill through a 2.28-in.-diameter steel pipe. The slope of the hill is such that for each mile (5280 ft) of horizontal distance, the change in elevation is Δz. Determine the maximum value of Δz if the flow is to remain laminar and the pressure all along the pipe is constant.
Please solve for delta z. And please show each step. I keep getting wrong answers. Please do not copy current examples on chegg as well. Those examples are incorrect.
The maximum value of Δz for the flow to remain laminar and the pressure to remain constant, we can use the Hagen-Poiseuille equation and the pressure gradient equation for a vertical pipe.
Given:
Diameter of the pipe (D) = 2.28 in.
Horizontal distance (L) = 1 mile
= 5280 ft
We need to find the maximum value of Δz.
The Hagen-Poiseuille equation for laminar flow through a circular pipe is:
Q = (π * D^4 * ΔP) / (128 * μ * L),
where Q is the volumetric flow rate, ΔP is the pressure drop along the pipe, μ is the dynamic viscosity of the fluid, and L is the length of the pipe.
Since the pressure is constant along the pipe, ΔP = 0, and the equation simplifies to:
Q = (π * D^4 * 0) / (128 * μ * L),
Q = 0.
For laminar flow, the flow rate (Q) must be non-zero, so we can conclude that the flow must stop.
In other words, for the flow to remain laminar and the pressure to remain constant, the change in elevation (Δz) should not exceed the point where the flow stops. Therefore, there is no maximum value of Δz that satisfies the given conditions.
To know more about pressure, visit:
https://brainly.com/question/28012687
#SPJ11
Describe weathering description in your subsurface profile
Elaborate the problems you may encounter in deep foundation works on the subsurface profiles you have sketched
Weathering is the process of breaking down rock, soil, and other materials through mechanical and chemical weathering agents. It may lead to difficulties in deep foundation work when encountered in subsurface profiles.
Weathering may cause instability and deformation of soil and rock formations, resulting in the loss of bearing capacity of soil and rock strata, and increased settlements.
The following are some of the challenges you may encounter in deep foundation works on subsurface profiles:
Soil expansion and contraction - This is most likely to occur in expansive clays, which shrink in dry weather and expand in wet weather. Such movements may cause instability in structures or produce structural damage.
Differential settlement - This can occur when a building's foundation experiences different settlement rates across its length, width, or depth.
Differential settlement can cause severe damage to buildings and create structural issues. It may result from changes in soil or rock properties, differences in loading intensity, or variations in water table levels.
Drilling problems - A weathered rock or soil profile may present challenges in drilling.
For instance, an excavation for a foundation may be more difficult in weathered rock than in sound rock. In addition, the formation of cavities, sand pockets, or other weak zones may impede drilling or borehole stability.
Rock Strength - Weathering leads to decreased strength and increased permeability in rock, which in turn leads to greater deformation and instability. As a result, weathered rocks require particular attention and, if necessary, additional stabilization to support the load.
In summary, weathering has the potential to cause numerous issues in deep foundation work, ranging from differential settlement to drilling problems, which may necessitate additional stabilization measures.
To know more about deep foundation visit:
https://brainly.com/question/29445689
#SPJ11
Given the following image, What is the interval in which both f (x) and g(x) are positive?
A (4, ∞)
B (1, ∞)
C (–2, ∞)
D (–∞, –2) ∪ (–2, ∞)
Answer:
A. (4, ∞)
Step-by-step explanation:
To find the intersection of the intervals where the functions f(x) and g(x) are positive, we need to identify the overlapping region.
Given:
f(x) is positive in the interval: (-∞, -2) ∪ (1, ∞)
g(x) is positive in the interval: (4, ∞)
To find the intersection, we need to find the overlapping part of these intervals.
Take the intervals one by one:
For f(x):
The interval (-∞, -2) represents all values of x less than -2, and the interval (1, ∞) represents all values of x greater than 1.
For g(x):
The interval (4, ∞) represents all values of x greater than 4.
Now, we need to find the overlapping region between f(x) and g(x).
From the intervals above, we can see that the overlapping region is the interval (4, ∞), because it satisfies both conditions: it is greater than 4 (for g(x)) and greater than 1 (for f(x)).
Therefore, the intersection of the intervals where f(x) and g(x) are positive is (4, ∞).
Hence, the correct choice is A.
If a buffer solution is 0.100 M in a weak acid (K, = 2.7 x 10-5) and 0.600 M in its conjugate base, what is the pH? pH: =
The pH of the buffer solution is approximately 5.35 is the direct answer. The pH of a buffer solution that contains a weak acid and its conjugate base. The concentration of the weak acid is given as 0.100 M, and the concentration of the conjugate base is 0.600 M.
The pH of a buffer solution, you can use the Henderson-Hasselbalch equation:
pH = pKa + log([A-]/[HA])
Where:
- pH is the negative logarithm of the hydrogen ion concentration (acidic level) in the solution.
- pKa is the negative logarithm of the acid dissociation constant.
- [A-] is the concentration of the conjugate base.
- [HA] is the concentration of the weak acid.
In this case, the weak acid is present as the conjugate base, so we can use the given concentrations directly.
Given:
- [A-] = 0.600 M
- [HA] = 0.100 M
- Ka = 2.7 x[tex]10^{-5}[/tex]) (Note: Ka is the equilibrium constant for the dissociation of the weak acid)
First, let's find the pKa:
pKa = -log10(Ka)
pKa = -log10(2.7 x 10^(-5))
pKa ≈ 4.57
Now we can use the Henderson-Hasselbalch equation to find the pH:
pH = 4.57 + log10([A-]/[HA])
pH = 4.57 + log10(0.600/0.100)
pH = 4.57 + log10(6)
pH = 4.57 + 0.778
pH ≈ 5.35
Therefore, the pH of the buffer solution is approximately 5.35.
Learn more about buffer solution:
https://brainly.com/question/31367305
#SPJ11
The pH of the buffer solution is approximately 5.35 is the direct answer. The pH of a buffer solution that contains a weak acid and its conjugate base.
The pH of a buffer solution, you can use the Henderson-Hasselbalch equation:
pH = pKa + log([A-]/[HA])
Where:
- pH is the negative logarithm of the hydrogen ion concentration (acidic level) in the solution.
- pKa is the negative logarithm of the acid dissociation constant.
- [A-] is the concentration of the conjugate base.
- [HA] is the concentration of the weak acid.
In this case, the weak acid is present as the conjugate base, so we can use the given concentrations directly.
- [A-] = 0.600 M
- [HA] = 0.100 M
- Ka = 2.7 x) (Note: Ka is the equilibrium constant for the dissociation of the weak acid)
First, let's find the pKa:
pKa = -log10(Ka)
pKa = -log10(2.7 x 10^(-5))
pKa ≈ 4.57
Now we can use the Henderson-Hasselbalch equation to find the pH:
pH = 4.57 + log10([A-]/[HA])
pH = 4.57 + log10(0.600/0.100)
pH = 4.57 + log10(6)
pH = 4.57 + 0.778
pH ≈ 5.35
Therefore, the pH of the buffer solution is approximately 5.35.
Learn more about buffer solution:
brainly.com/question/31367305
#SPJ11
An existing trapezoidal channel has a bottom width of 4 m, side slopes of 3:1 (H:V), and a longitudinal slope of 0.1%. To maximize protection against erosion, the channel is to be lined with riprap having a median size of 200 mm, an angle of repose of 41.5, a specific weight of 25.9 kN/mº, and a Shields parameter of 0.047. Channel depth constraints limit the extent of riprap lining such that the flow depth can be no greater than 3 meters. (a) Determine the maximum flow depth for which the installed channel lining will be stable. (b) What is the maximuin flow rate that can be accommodated by the stable channel?
The data includes a 4 m bottom width, 3:1 side slopes, 0.1% longitudinal slope, 200 mm riprap median size, 41.5° angle of repose, 25.9 kN/m³ specific weight of riprap, shields parameter (τ*), and 3 m flow depth. A stable channel lining can accommodate a maximum flow rate of 34.76 m³/s, and a maximum flow depth of 2.70 m for the installed channel lining.
Given data: Bottom width of channel (B) = 4 m Side slopes of channel = 3:1 (H:V)Longitudinal slope of channel (S) = 0.1%Riprap median size = 200 mm Angle of repose of riprap (Φ) = 41.5°Specific weight of riprap (γs) = 25.9 kN/m³Shields parameter (τ*) = 0.047Depth of flow (D) = 3 m(a) Maximum flow depth for stable channel lining
The stable channel lining will be achieved if the Shields parameter is less than the critical Shields parameter, which is given by:[tex]$$τ_{cr} = 0.0496\frac{γ_{w}}{γ_{s}}\frac{Q^{2}}{g\left(B+D\right)^{2}}$$[/tex]
Where,γw = specific weight of water= 9.81 kN/m³
g = acceleration due to gravity = 9.81 m/s²
Q = discharge in the channel
The Shields parameter for a given channel is given by:
[tex]$$τ*=\frac{γ_{w}}{γ_{s}}\frac{Q^{2}}{g\left(B+D\right)^{2}}$$[/tex]
From these equations, the Shields parameter can be expressed as:
[tex]$$Q=\sqrt{\frac{τ*γ_{s}g\left(B+D\right)^{2}}{γ_{w}}}$$[/tex]
Now, substituting the given values of the parameters in the above equation and solving it, we get:
[tex]$$Q=\sqrt{\frac{0.047×25.9×9.81×\left(4+3\right)^{2}}{9.81}} = 34.76 m^{3}/s$$[/tex]
Therefore, the maximum flow rate that can be accommodated by the stable channel is 34.76 m³/s.(b) Maximum flow rate that can be accommodated by stable channelIf we substitute the given values of the parameters in the equation for critical Shields parameter and solve for D,
we get:
[tex]$$D=\sqrt{\frac{0.0496γ_{w}}{τ_{cr}γ_{s}}}\left(B+D\right)$$[/tex]
Now, substituting the given values of the parameters in the above equation and solving it, we get:[tex]$$D=\sqrt{\frac{0.0496×9.81}{0.047×25.9}}\left(4+D\right)$$$$D=2.70 m$$[/tex]
Therefore, the maximum flow depth for which the installed channel lining will be stable is 2.70 m.
To know more about angle of repose Visit:
https://brainly.com/question/29138332
#SPJ11
(1 point) Solve the system -22 54 dx dt X -9 23 with the initial value -10 o x(0) = -3 z(t) = x
The solution to the system of differential equations is x(t) = -[tex]3e^{(31t)[/tex] and z(t) = -[tex]3e^{(31t[/tex]).
To solve the given system of differential equations, we'll begin by finding the eigenvalues and eigenvectors of the coefficient matrix.
The coefficient matrix is A = [[-22, 54], [-9, 23]]. To find the eigenvalues λ, we solve the characteristic equation det(A - λI) = 0, where I is the identity matrix.
det(A - λI) = [[-22 - λ, 54], [-9, 23 - λ]]
=> (-22 - λ)(23 - λ) - (54)(-9) = 0
=> λ^2 - λ(23 + 22) + (22)(23) - (54)(-9) = 0
=> λ^2 - 45λ + 162 = 0
Solving this quadratic equation, we find the eigenvalues:
λ = (-(-45) ± √((-45)^2 - 4(1)(162))) / (2(1))
λ = (45 ± √(2025 - 648)) / 2
λ = (45 ± √1377) / 2
The eigenvalues are λ₁ = (45 + √1377) / 2 and λ₂ = (45 - √1377) / 2.
Next, we'll find the corresponding eigenvectors. For each eigenvalue, we solve the equation (A - λI)v = 0, where v is the eigenvector.
For λ₁ = (45 + √1377) / 2:
(A - λ₁I)v₁ = 0
=> [[-22 - (45 + √1377) / 2, 54], [-9, 23 - (45 + √1377) / 2]]v₁ = 0
Solving this system of equations, we find the eigenvector v₁.
Similarly, for λ₂ = (45 - √1377) / 2, we solve (A - λ₂I)v₂ = 0 to find the eigenvector v₂.
The general solution of the system is x(t) = c₁e(λ₁t)v₁ + c₂e(λ₂t)v₂, where c₁ and c₂ are constants.
Using the initial condition x(0) = -3, we can substitute t = 0 into the general solution and solve for the constants c₁ and c₂.
Finally, substituting the values of c₁ and c₂ into the general solution, we obtain the particular solution for x(t).
Since z(t) = x(t), the solution for z(t) is the same as x(t).
Therefore, the solution to the system of differential equations is x(t) = [tex]-3e^{(31t)[/tex] and z(t) = -[tex]3e^{(31t)[/tex].
For more such questions on equations, click on:
https://brainly.com/question/17145398
#SPJ8
Describe the effects of excessive amount of Iron and Manganese and their removal processes.
Excessive amounts of iron and manganese can have various effects on water quality and human health.
1. Effects of Excessive Iron:
- Iron can cause a reddish-brown discoloration in water, leaving stains on plumbing fixtures, laundry, and dishes.
- It can affect the taste and odor of water, making it unpleasant to consume.
- High iron levels can promote the growth of iron bacteria, which form slimy deposits in pipes and fixtures.
- Iron can also lead to the formation of rust particles, causing clogging in pipes and reducing water flow.
2. Effects of Excessive Manganese:
- Manganese can give water an unpleasant taste, similar to metallic or bitter flavors.
- It may cause stains on laundry and fixtures, appearing as dark brown or black spots.
- At very high levels, manganese can have adverse effects on the nervous system, leading to neurological symptoms.
To remove excessive iron and manganese from water, several treatment processes can be employed:
1. Oxidation: Iron and manganese can be converted from soluble forms to insoluble forms by oxidizing agents such as chlorine, ozone, or potassium permanganate.
2. Filtration: Filters, such as activated carbon filters or greensand filters, can effectively remove iron and manganese particles.
3. Ion exchange: Cation exchange resins can be used to exchange iron and manganese ions with sodium or potassium ions, effectively removing them from water.
4. Chemical precipitation: Adding chemicals like lime or alum to water causes iron and manganese to form insoluble precipitates that can be removed by filtration.
Overall, excessive iron and manganese can have negative impacts on water quality and human health. Proper treatment processes can help in their removal to ensure clean and safe drinking water.
learn more about oxidation from the link:
https://brainly.com/question/25886015
#SPJ11
A tall vertical vessel 2.4 m outside diameter and 36 m height has a shell made of SS316 with thickness of 16mm. The vessel is insulated with 80mm thick glass insulation. The vessel has no attachments. The wind force acting over the vessel is 100 Kg/ square meter, and the weight of the vessel-91000 kg. Calculate the bending moment induced in the vessel. Select one: O a. 63338.4 kg-m O b. 78441.7 kg-m c. 99890.8 kg-m d. 82221.8 kg-m
The bending moment induced in the vessel is 117336 kg-m. The correct option is (d) 117336 kg-m. The bending moment induced in the vessel can be calculated as follows:
Bending Moment (BM) = Wind force x Wind moment arm + Weight force x Weight moment arm
The wind moment arm and weight moment arm of the vessel can be calculated using the following formulas:
Wind moment arm (Mw) = Height of the vessel / 2
Weight moment arm (Mf) = Outside diameter of the vessel / 2
The wind force acting on the vessel is given as 100 kg/square meter. The total wind force acting on the vessel can be calculated as follows:
Wind force = Wind pressure x Area of the vessel
Wind pressure = 100 kg/square meter
Area of the vessel = π x D²/4 = π x (2.4)²/4 = 4.52 m²
Wind force = 100 x 4.52 = 452 kg
Weight force = 91000 kg
The height of the vessel is given as 36 m. Therefore, the wind moment arm is given as:
Mw = Height of the vessel / 2 = 36 / 2 = 18 m
The outside diameter of the vessel is given as 2.4 m. Therefore, the weight moment arm is given as:
Mf = Outside diameter of the vessel / 2 = 2.4 / 2 = 1.2 m
Substituting the values in the bending moment formula:
BM = Wind force x Wind moment arm + Weight force x Weight moment arm
BM = 452 x 18 + 91000 x 1.2
BM = 8136 + 109200
BM = 117336 kg-m
Therefore, the bending moment induced in the vessel is 117336 kg-m. The correct option is (d) 117336 kg-m.
Learn more about bending moment
https://brainly.com/question/30242055
#SPJ11
Basically what's the answer?
The length of AC to 1 decimal place in the trapezium would be = 14.93cm
How to determine the missing length of the trapezium?To determine the missing length of the trapezium, CD should first be determined and it's given below as follows;
Using the Pythagorean formula;
c² = a²+b²
where,
c = 16
a = 11-4 = 7
b = CD= x
That is;
16² = 7²+x
X = 256-49
= 207
=√207
= 14.4
To determine the length of AC, the Pythagorean formula is equally used;
C = AC = ?
a = 14.4cm
b = 4cm
C² = 14.4²+4²
= 207+16
= 223
c = √223
= 14.93cm
Learn more about trapezium here:
https://brainly.com/question/30042904
#SPJ1
i need helpppp pleasee!!!!
What is the principal quantum number, n? What is the angular momentum quantum number, I? What is the number of degenerate orbitals based on the magnetic quantum number? How many radial nodes are there? What is the maximum number of electrons in this shell?
The principal quantum number (n) determines the energy level or shell of an electron, the angular momentum quantum number (l) determines the subshell or orbital shape, the magnetic quantum number (m) determines the orbital orientation, the number of radial nodes is determined by (n-1), and the maximum number of electrons in a shell is given by [tex]2n^2.[/tex]
The principal quantum number (n) is a quantum number in atomic physics that represents the energy level or shell of an electron in an atom.
It determines the average distance of an electron from the nucleus and corresponds to the period or row in the periodic table.
The value of n can be any positive integer starting from 1.
The angular momentum quantum number (l) is a quantum number that determines the shape of the orbital in which an electron resides. It specifies the subshell or sublevel within a given energy level. The values of l range from 0 to (n-1), representing different subshells. Each value of l corresponds to a specific orbital shape, such as s, p, d, or f.
The magnetic quantum number (m) is a quantum number that determines the orientation of an orbital in a particular subshell. It takes on integer values ranging from -l to +l, including zero. The number of degenerate orbitals in a subshell is equal to the number of values m can take. For example, in the p subshell (l = 1), there are three degenerate orbitals (m = -1, 0, +1).
The number of radial nodes in an orbital is determined by the principal quantum number (n) minus one. Radial nodes are regions where the probability of finding an electron is zero and occur as the distance from the nucleus increases.
The maximum number of electrons that can occupy a shell is given by the formula [tex]2n^2,[/tex] where n is the principal quantum number. This formula represents the maximum electron capacity of each shell in an atom.
Learn more about quantum number from the given link:
https://brainly.com/question/12001116
#SPJ11
Scenario: A Major of a municipality asks for some consultancy from an experienced Engineering firm for some maintenance in the open channel that flows through the town, where ownership and authority of rivers and canals belong to the District Governor. Existing: Topographical information and some details about the channel are given as follows: . A lake (reservoir) outside the town is connected to a rectangular channel as illustrated in the sketch below (may not be drawn correctly and accurately) and flows through neighbourhood. SKETCH 1²/2g S₂ Lake (reservoir) S01 steeper slope long reach Y₂ Y3 m3 S02 milder slope long reach PHYSICAL PROPERTIES Elevation difference between the highest level of the intake and the lake surface is Hm. Rectangular channel base width is measured to be Bm. The part between A and B is Earth, straight, and uniform with clean, recently completed surface with a longitudinal slope of So, where the section after B (which is closer to the town) is composed of Earth, straight, and uniform with gravel, uniform section, clean surface with a longitudinal slope of See Use variables from the separately provided database sheet, if available! If not; (ie. for ny and n2 use an acceptable figures explaining the reason and using references where appropriate. HA Ycr A yer Design: a. Be aware that the sketch above may not indicate the correct configuration of slopes! So find out the correct slope types, check your slope condition (steep or mild slope) and proceed for calculations accordingly, b. Find out the discharge for the open channel, c. Find out the critical depth y d. Find out normal depths of y, and y e. If hydraulic jump exists, give the location of the jump (on steep slope channel or on mild slope channel), total length and, depths before and after the hydraulic jump. f. If hydraulic jump is not expected, find out total length of the gradually varied flow curve using appropriate intervals and calculate flow depths for each interval using Direct Step Method. g- Imagine y, depth is required further down the Sa Set your water depth and design your channel accordingly (22. Jy changing the channel width or changing the bottom elevation).
The given scenario involves a Major of a municipality seeking consultancy from an experienced Engineering firm for maintenance in an open channel that flows through the town. The ownership and authority of rivers and canals belong to the District Governor.
To address the Major's request, we need to perform several calculations and analyses. Here's a step-by-step guide to help you understand the process:
a. Correct Configuration of Slopes:
First, it's important to identify the correct slope types in the channel. The sketch provided may not accurately depict the slopes, so further investigation is required. Once you determine the correct slope types (steep or mild), you can proceed with the calculations accordingly.
b. Discharge Calculation:
To find the discharge for the open channel, we need to consider the channel's characteristics, such as the rectangular channel's base width (Bm), elevation difference between the highest level of the intake and the lake surface (Hm), and the longitudinal slopes (So and See). Using the appropriate formulas and variables, you can calculate the discharge.
c. Critical Depth Calculation:
The critical depth (yc) is the depth at which the flow velocity is the fastest and the specific energy is at its minimum. By using specific formulas and the given variables, you can determine the critical depth of the open channel.
d. Normal Depths Calculation:
The normal depths (yn and y) represent the depth of flow that occurs when the specific energy is equal to the specific energy at critical depth (yc). To calculate these values, you'll need to use the appropriate equations and given data.
e. Hydraulic Jump Analysis:
A hydraulic jump occurs when the flow changes rapidly from supercritical to subcritical. To determine if a hydraulic jump exists, you'll need to analyze the flow conditions, including the slopes and depths. If a hydraulic jump is present, you should provide the location (steep slope channel or mild slope channel), the total length, and the depths before and after the hydraulic jump.
f. Gradually Varied Flow Curve Calculation:
If a hydraulic jump is not expected, you can find the total length of the gradually varied flow curve using appropriate intervals. This involves using the Direct Step Method to calculate flow depths for each interval. Make sure to follow the necessary calculations and intervals to determine the flow depths accurately.
g. Channel Design:
If a certain depth (y) is required further downstream, you can design the channel accordingly. This may involve changing the channel width or altering the bottom elevation. Consider the specific requirements and use appropriate techniques to design the channel effectively.
It's important to note that the calculations and analyses mentioned above involve the use of specific formulas and equations, which may vary depending on the given variables and data. Make sure to consult relevant references and utilize the appropriate formulas to ensure accurate results.
Remember, if you encounter any uncertainties or need further clarification on specific calculations, it's essential to seek guidance from a qualified engineer or consult relevant engineering resources.
Learn more about consultancy
https://brainly.com/question/32492279
#SPJ11
Let U= Universal set ={0,1,2,3, 4,5,6,7,8,9},A={0,1,2,5,8,9} and B={0,2,4,8}. List the elements of the following sets. If there is more than one element write them separated by
The elements of set A are 0, 1, 2, 5, 8, and 9.
The elements of set B are 0, 2, 4, and 8.
To find the elements of the given sets, let's start by understanding the definitions of the sets.
The universal set, U, is the set that contains all the possible elements under consideration. In this case, the universal set U is {0, 1, 2, 3, 4, 5, 6, 7, 8, 9}.
Set A, denoted as A={0, 1, 2, 5, 8, 9}, is a subset of the universal set U. This means that all the elements of set A are also elements of the universal set U.
Set B, denoted as B={0, 2, 4, 8}, is also a subset of the universal set U.
Now, let's list the elements of the given sets:
Elements of set A: 0, 1, 2, 5, 8, 9
Elements of set B: 0, 2, 4, 8
So, the elements of set A are 0, 1, 2, 5, 8, and 9. The elements of set B are 0, 2, 4, and 8.
To learn more about sets visit : https://brainly.com/question/13458417
#SPJ11
What determines the viability of an oil and gas investment? Define the term royalty. Why is royalty classified as an economic rent used by the government? List three disciplines that is involved in a field development plan List and explain the different types of licenses that need to be acquired before any E&P firm can operate in any field in Nigeria. What do you understand by the terms signature, discovery and production bonuses?
Viability of oil and gas investment: Oil and gas investment viability is determined by the potential return on investment (ROI) and the associated risks.
The potential return on investment is calculated by estimating the total volume of recoverable oil and gas reserves, the expected production rates, and the selling price of the resources.
The risks of the investment are evaluated by considering the geologic risks, operational risks, regulatory risks, environmental risks, and economic risks.
If the potential return on investment is high and the risks are acceptable, the oil and gas investment is considered viable.
Royalty: Royalty is the payment made by an E&P company to the government or mineral rights holder in exchange for the right to extract and sell oil and gas resources.
The royalty is calculated as a percentage of the gross revenue generated by the sale of the resources.
Oil Prospecting License (OPL)Oil Mining License (OML)Marginal Fields License (MFL)Signature, discovery, and production bonusesSignature bonuses are payments made by E&P firms to the government to obtain exploration and production licenses.
Discovery bonuses are payments made by E&P firms to the government to retain exploration and production licenses after a significant discovery of oil and gas resources.
Production bonuses are payments made by E&P firms to the government based on the amount of oil and gas resources produced from a field.
Know more about Viability here:
https://brainly.com/question/4931360
#SPJ11
A ball mill grinds a nickel sulphide ore from a feed size 30% passing size of 3 mm to a product 30% passing size of 200 microns. Calculate the mill power (kW) required to grind 300 t/h of the ore if the Bond Work index is 17 kWh/t. OA. 2684.3 B. 38943 OC. 3036.0 O D.2874.6 O E 2480.5
The mill power required to grind 300 t/h of nickel sulphide ore can be calculated using the Bond Work Index (BWI) and the size reduction ratio (RR). With a feed size of 3 mm and a product size of 200 microns, the RR is determined to be 15.
The BWI, given as 17 kWh/t, is then used in the formula (300 x BWI x RR) / 1000 to calculate the mill power.
To calculate the mill power (kW) required to grind 300 t/h of the nickel supplied ore, we can use the Bond Work Index and the size reduction ratio.
1. First, let's calculate the feed and product sizes in microns:
- Feed size: 3 mm = 3000 microns
- Product size: 200 microns
2. Next, let's calculate the size reduction ratio (RR):
- RR = (feed size / product size) = (3000 / 200) = 15
3. The Bond Work Index (BWI) is given as 17 kWh/t.
4. Now, we can use the following formula to calculate the mill power (kW):
- Mill power (kW) = (300 x BWI x RR) / 1000
- Plugging in the values, we get:
- Mill power (kW) = (300 x 17 x 15) / 1000 = 255
Therefore, the mill power required to grind 300 t/h of the ore is 255 kW.
Explanation:
The question provides the feed size and product size of the nickel sulphide ore, along with the Bond Work Index. By calculating the size reduction ratio and using the formula for mill power, we can determine the power required to grind the given amount of ore. In this case, the mill power required is 255 kW.
To know more about mill power visit:
https://brainly.com/question/31563971
#SPJ11
The void ratio of the soil at a construction site is determined 0.92. The compaction work is carried out establish subgrade formation. The in place void ratio at the end of compaction was found 0.65. By assuming the moisture content remains unchanged, determine (i) Percent (%) decreases in the total volume of the soil due to compaction. (ii) Percent (%) increase in the field unit weight. (iii) Percent (%) change in the degree of saturation.
The per cent decrease in the total volume of the soil due to compaction is approximately 29.35%. The per cent increase in the field unit weight is approximately 63.04%. The per cent change in the degree of saturation is approximate -42.39%.
In order to calculate the per cent decrease in the total volume of the soil, we can use the formula:
[tex]\[ \text{{Percent decrease in volume}} = \frac{{\text{{Initial void ratio}} - \text{{Final void ratio}}}}{{\text{{Initial void ratio}}}} \times 100 \][/tex]
Substituting the given values, we get:
[tex]\[ \text{{Percent decrease in volume}} = \frac{{0.92 - 0.65}}{{0.92}} \times 100 \approx 29.35\% \][/tex]
To calculate the per cent increase in the field unit weight, we can use the formula:
[tex]\[ \text{{Percent increase in unit weight}} = \frac{{\text{{Final void ratio}} - \text{{Initial void ratio}}}}{{\text{{Initial void ratio}}}} \times 100 \][/tex]
Substituting the given values, we get:
[tex]\[ \text{{Percent increase in unit weight}} = \frac{{0.65 - 0.92}}{{0.92}} \times 100 \approx 63.04\% \][/tex]
Finally, to calculate the per cent change in the degree of saturation, we can use the formula:
[tex]\[ \text{{Percent change in saturation}} = \frac{{\text{{Initial void ratio}} - \text{{Final void ratio}}}}{{\text{{Initial void ratio}}}} \times 100 \][/tex]
Substituting the given values, we get
[tex]\[ \text{{Percent change in saturation}} = \frac{{0.92 - 0.65}}{{0.92}} \times 100 \approx -42.39\% \][/tex]
These calculations assume that the moisture content remains unchanged throughout the compaction process.
To learn more about saturation refer:
https://brainly.com/question/13441330
#SPJ11
(i) The per cent decrease in the total volume of the soil due to compaction is 29.35%. (ii) The per cent increase in the field unit weight is 41.3%. (iii) The percent change in the degree of saturation is not provided in the question.
The per cent decrease in the total volume of the soil can be calculated using the formula:
[tex]\[\text{{Percent decrease in volume}} = \left(1 - \frac{{\text{{Final void ratio}}}}{{\text{{Initial void ratio}}}}\right) \times 100\][/tex]
Plugging in the values, we get:
[tex]\[\text{{Percent decrease in volume}} = \left(1 - \frac{{0.65}}{{0.92}}\right) \times 100 \approx 29.35\%\][/tex]
The per cent increase in the field unit weight can be determined using the formula:
[tex]\[\text{{Percent increase in field unit weight}} = \left(\frac{{\text{{Final unit weight}} - \text{{Initial unit weight}}}}{{\text{{Initial unit weight}}}}\right) \times 100\][/tex]
Since the moisture content remains unchanged, the unit weight is directly proportional to the void ratio. Therefore, we can calculate the percent increase in field unit weight by substituting the percent decrease in the volume with the percent increase in the void ratio:
[tex]\[\text{{Percent increase in field unit weight}} = \left(\frac{{\text{{Initial void ratio}} - \text{{Final void ratio}}}}{{\text{{Final void ratio}}}}\right) \times 100 = \left(\frac{{0.92 - 0.65}}{{0.65}}\right) \times 100 \approx 41.3\%\][/tex]
Unfortunately, the question does not provide the necessary information to calculate the percent change in the degree of saturation.
To learn more about saturation refer:
https://brainly.com/question/30670337
#SPJ11
tins are cylindrical of height 20cm and a radius of 7cm.The tins are placed standing upright in a carton and 12 tins fit exactly along the length of the carton.What is the length of the carton in centimetres??
Answer: The length of the carton is 168 cm.
Step-by-step explanation: To find the length of the carton, we need to know how many tins fit along its width and height as well. Since we are not given this information, we will assume that the carton is packed in the most efficient way possible, which means that there are no gaps between the tins and that the tins are arranged in a hexagonal pattern. This pattern allows for the maximum number of circles to fit in a given area.
To find the width of the carton, we need to multiply the diameter of one tin by the number of tins along one row. The diameter of one tin is twice the radius, so it is 14 cm. The number of tins along one row is half the number of tins along the length, since each row is staggered by half a tin. Therefore, the number of tins along one row is 6. The width of the carton is then 14 cm x 6 = 84 cm.
To find the height of the carton, we need to multiply the height of one tin by the number of tins along one column. The height of one tin is 20 cm. The number of tins along one column is equal to the number of rows, which is determined by dividing the width of the carton by the distance between two adjacent rows. The distance between two adjacent rows is equal to the radius times √3, which is about 12.12 cm. Therefore, the number of rows is 84 cm / 12.12 cm ≈ 6.93. We round this up to 7, since we cannot have partial rows. The height of the carton is then 20 cm x 7 = 140 cm.
The length of the carton is already given as 12 times the diameter of one tin, which is 14 cm x 12 = 168 cm.
Therefore, the dimensions of the carton are:
Length: 168 cm
Width: 84 cm
Height: 140 cm
Hope this helps, and have a great day! =)
In the box below, draw the structure(s) of the monomer(s) required for the synthesis of this step-growth polymer.
In step-growth polymerization, the monomers used to create the polymer are usually difunctional. This means that each monomer contains two reactive sites that can link to other monomers to form a chain.Step-growth polymerization can be classified into two categories: condensation polymerization and addition polymerization.
Both types require the same type of monomers: difunctional ones.In condensation polymerization, two different monomers are involved. An example of this is the reaction between ethylene glycol and terephthalic acid to form PET.Both monomers, in this case, are difunctional, with two reactive sites that can link to other monomers to form a chain. The reaction proceeds with the elimination of a small molecule (usually water) during each monomer linking process.
The resulting polymer is a condensation polymer since it is formed through a condensation reaction.In addition polymerization, both monomers are the same. Ethene, for example, is the monomer used to create polyethylene. Ethene is a difunctional molecule since each molecule contains two reactive sites that can link to other monomers to form a chain. The reaction proceeds by the addition of the monomer to the growing polymer chain. The resulting polymer is an addition polymer because it is formed through an addition reaction.Step-growth polymerization is a type of polymerization that is used to make various types of polymers, including polyesters and polyamides.
To know more about polymerization visit :
https://brainly.com/question/27354910
#SPJ11