The power emitted by a monochromatic source is 6.3 m Wavelength of light emitted by the source is 600 nm.
1. Energy of photon, E = hc/λ
where, h = Planck's constant = 6.63 × 10⁻³⁴ Js, c = Speed of light = 3 × 10⁸ m/s, λ = wavelength of light= 600 nm = 600 × 10⁻⁹ m
Substitute the values, E = (6.63 × 10⁻³⁴ J.s × 3 × 10⁸ m/s)/(600 × 10⁻⁹ m) = 3.31 × 10⁻¹⁹ J1 eV = 1.6 × 10⁻¹⁹ J
Hence, Energy of photon in eV, E = (3.31 × 10⁻¹⁹ J)/ (1.6 × 10⁻¹⁹ J/eV) = 2.07 eV (approx.)
2. The power is given by,
P = Energy/Time Energy, E = P × Time Where P = 6.3 mW = 6.3 × 10⁻³ W, Time = 10 minutes = 10 × 60 seconds = 600 seconds
E = (6.3 × 10⁻³ W) × (600 s) = 3.78 J
Number of photons emitted, n = E/Energy of each photon = E/E1 = 3.78 J/3.31 × 10⁻¹⁹ J/photon ≈ 1.14 × 10²¹ photons
3. The work function (ϕ) of a metal is the minimum energy required to eject an electron from the metal surface. It is given by the relation, K max = hv - ϕ where Kmax = Maximum kinetic energy of the ejected electron, v = Frequency of the incident radiation (v = c/λ), and h = Planck's constant.
Using Kmax = 0.55 eV = 0.55 × 1.6 × 10⁻¹⁹ J, h = 6.63 × 10⁻³⁴ Js, λ = 600 nm = 600 × 10⁻⁹ m,v = c/λ = 3 × 10⁸ m/s ÷ 600 × 10⁻⁹ m = 5 × 10¹⁴ s⁻¹.
Substituting all the values in the above formula,ϕ = hv - Kmaxϕ = (6.63 × 10⁻³⁴ Js × 5 × 10¹⁴ s⁻¹) - (0.55 × 1.6 × 10⁻¹⁹ J)ϕ ≈ 4.3 × 10⁻¹⁹ J
Therefore, the work function of the metal is approximately equal to 4.3 × 10⁻¹⁹ J.
Explore another question on work function of metals: https://brainly.com/question/19427469
#SPJ11
A gas expands from an initial state A to a final state B. The expansion process consists of two stages. First the gas expands at constant pressure from 20 litres to 42 litres. Second the gas expands from 42 litres to 88 litres with a pressure drop according to the equation P = (100 - 0.8 V) kPa, where V is in litres. Calculate the work done on the gas. [Note that you need to calculate the initial pressure, which is not 100kPa.] a.-3889 J O b.-3669 J O c.-4199 J O d. -4039 J O e. 3539 J
The work done on the gas during the expansion process can be calculated by integrating the pressure with respect to the volume over each stage of the process. The total work done on the gas is approximately -3669 J.
To calculate the work done on the gas, we need to determine the pressure as a function of volume for each stage of the expansion process.
In the first stage, the gas expands at constant pressure. Since we know the initial and final volumes, we can calculate the constant pressure using the ideal gas law: PV = nRT. Given that the initial volume is 20 liters and the final volume is 42 liters, we have P₁ * 20 = nRT and P₂ * 42 = nRT, where P₁ and P₂ are the pressures at the initial and final states, respectively. Dividing the second equation by the first equation, we can solve for P₂/P₁ and find P₂ = 2.1P₁.
In the second stage, the pressure is given by the equation P = (100 - 0.8V) kPa. We can integrate this equation with respect to volume to find the work done during this stage.
The total work done on the gas is the sum of the work done in each stage. By integrating the pressure-volume relationship over each stage and summing the results, we find that the total work done on the gas is approximately -3669 J.
Learn more about work done here:
https://brainly.com/question/2750803
#SPJ11
A resistor has the following colored stripes: red, red, black, gold. Its resistance is equal to:
a. 220 Ω b. 0.220 Ω c. 2220 Ω d. 22 Ω
A resistor has the following colored stripes: red, red, black, gold. Its resistance is equal to 22 , option d.
A resistor is a circuit element that restricts current flow. Resistance is the resistance of a substance to the flow of electricity. The resistance of a circuit is determined by resistors.
In electrical circuits, resistor color coding is commonly utilized to recognize the resistance of a resistor. A series of colored stripes are used to indicate the resistance of a resistor. A digit or number corresponds to each colored stripe. Here is the code for the colors of the stripes:
Color 1 = digit 1
Color 2 = digit 2
Color 3 = multiplier
Color 4 = tolerance
Gold is the tolerance level.
To decode the colors on the resistor, we use this formula:
Resistance = (Digit 1 * 10 + Digit 2) * Multiplier
Digit 1 = Red
Digit 2 = Red
Multiplier = Black
Tolerance = Gold
Resistance = (2 * 10 + 2) * 1
Resistance = 22 Ω
Therefore, a resistor has the following colored stripes: red, red, black, gold. Its resistance is equal to 22 Ω.
Learn more about resistor: https://brainly.com/question/30140807
#SPJ11
An object with initial momentum 6 kg: m/s to the left is acted upon by a force F = 48 N to the right for a short time interval, At. At the end of this time interval, the momentum of the object is 2 kg · m/s to the right. How long was the time interval, At ? 2/3 s 1/12 s 1/2 s 1/3 s 1/24 s 1/6 s 1/4 s
The time interval is given in seconds, therefore, the time interval for which force is applied, At is 1/2 s. The correct option for the given question is c. 1/2 s.
Here is the explanation:
Given data,
Initial momentum, p₁ = -6 kg m/s
Force applied, F = 48 N
Final momentum, p₂ = 2 kg m/s
The time interval for which the force is applied is At. The momentum of an object is given as:
p = mv
Where, p = momentum, m = mass, v = velocity
Initially, the object is moving towards the left, therefore, the velocity is negative. And, finally, the object is moving towards the right, therefore, the velocity is positive.
Initially, momentum is given as:
p₁ = -6 kg m/s
Using the law of conservation of momentum;
p₁ = p₂
⇒ -6 = 2m
⇒ m = -6/2 = -3 kg
Therefore, mass is equal to 3 kg.
Initially, the velocity of the object is given by:
p₁ = -6 = -3 v₁
⇒ v₁ = 2 m/s
The force applied can be found out using the following formula:
F = Δp/Δt
Where, Δp = Change in momentum = p₂ - p₁ = 2 - (-6) = 8 kg m/s
F = 48 N
Δt = F/Δp = 48/8 = 6 s
But, the time interval is given in seconds, therefore, the time interval for which force is applied, At is:
At = Δt/2 = 6/2 = 3 s. Answer: 1/2 s.
To learn more about Initial momentum refer:-
https://brainly.com/question/12450698
#SPJ11
- Angular Momentum
\[
\begin{array}{l}
L_{\text {sun }}=0.1 M_{\text {sun }} R^{2} \text { sun } \Omega=3 \times 10^{48} \mat
I don't understand how this is calculated.
The question was "In an isolated system, the total angular momentum is conserved. Calculate the angular momentum of the Earth and compare it with the angular momentum of the sun."
a) Please help me calculate angular momentum of the Earth based on the calculation on the image above
b) Compare it with the angular momentum of the sun
The angular momentum of the Earth is approximately 2.66 × 10^40 kg·m²/s, and the angular momentum of the Sun is approximately 1.90 × 10^47 kg·m²/s.
Angular momentum is a property of rotating objects and is given by the equation L = Iω, where L is the angular momentum, I is the moment of inertia, and ω is the angular velocity. The moment of inertia of a planet can be calculated using the formula I = 2/5 * m * r², where m is the mass of the planet and r is its radius.
To calculate the angular momentum of the Earth, we need to determine its moment of inertia and angular velocity. The mass of the Earth is approximately 5.97 × 10^24 kg, and its radius is approximately 6.37 × 10^6 m. The angular velocity of the Earth can be approximated as the rotational speed of one revolution per day, which is approximately 7.27 × 10^(-5) rad/s. Plugging these values into the formula, we find that the angular momentum of the Earth is approximately 2.66 × 10^40 kg·m²/s.
In comparison, the angular momentum of the Sun can be calculated in a similar manner. The mass of the Sun is approximately 1.99 × 10^30 kg, and its radius is approximately 6.96 × 10^8 m. Using the same formula and considering the Sun's angular velocity, we find that the angular momentum of the Sun is approximately 1.90 × 10^47 kg·m²/s.
Learn more about angular momentum here:
https://brainly.com/question/30656024
#SPJ11
4. Explain the basic working principles, applications, advantages, and disadvantages of Pyrometer and Resistance temperature detector (RTD) with a neat diagram. 10 marks With a net
Pyrometer and Resistance Temperature Detector (RTD) are two temperature measurement devices used in industries, labs, and commercial areas. Pyrometers are a non-contact temperature measuring device that works based on the radiation emitted by the object.
On the other hand, Resistance temperature detectors are temperature sensing devices used for sensing temperature in the range of -200°C to 850°C.Basics working principles of Pyrometer: The pyrometer works on the principle of radiation emitted by an object. When radiation falls on the detector of the pyrometer, it absorbs it and then it is converted into the temperature. Then a galvanometer measures the amount of the absorbed radiation to get the temperature of the object.Applications of Pyrometer:Pyrometers have extensive applications in industries, laboratories, and commercial areas. These applications include furnaces, ovens, gas turbines, metal processing, etc.Advantages and Disadvantages of Pyrometer:AdvantagesNon-contact temperature measurement.High-temperature range.Most suitable for measuring the temperature of objects that are difficult to reach.DisadvantagesExpensive.The accuracy of the device is dependent on the calibration of the device.Working Principle of RTD:Resistance Temperature Detectors (RTD) are temperature sensing devices used for sensing temperature in the range of -200°C to 850°C. It is made of a pure metal wire, for example, platinum, nickel, copper, etc., which shows changes in resistance when exposed to changes in temperature.Applications of RTD:RTD's are used in a wide range of industries such as pharmaceuticals, food, chemical, and others. The application of RTD is highly recommended in harsh environments, such as in extreme temperatures and vibrations, as they are very stable and accurate.Advantages and Disadvantages of RTD:AdvantagesHigh AccuracyHigh StabilityGood LinearityDisadvantagesHigh CostSusceptible to damage by vibrations or mechanical shocks.
To know more about resistance pyrometer visit:
https://brainly.com/question/15415251
#SPJ11
Applications of Electrostatics The electric field one-fourth of the way from a charge 4: to another charge 92 is zero. What is the ratio of 1 to 4z?
The electric field is the area around electrically charged particles where the interaction between them creates an electric force. Electrostatics finds applications in a wide range of areas, including in the following fields:
In the industry, electrostatics is used to eliminate dirt and dust from plastic surfaces before painting them to achieve good adhesion. Aerospace engineering uses electrostatics in applications like the electrostatic cleaning of dust from the surface of spacecraft or the charging of space probes and dust detectors.
Medical technology relies on electrostatics in a range of applications, including in electrocardiography, electrophoresis, and in the use of electrostatic precipitators for respiratory protection.The electric field one-fourth of the way from a charge 4 to another charge 92 is zero.
What is the ratio of 1 to 4z?
The distance between charge 4 and charge 92 is 4z. Therefore, we can say that the electric field is zero at a distance of z from charge 4 (since z is 1/4th of the distance between 4 and 92).
Using Coulomb's law, we can calculate the electric field as:
E = (kQq)/r² Where k is the Coulomb constant, Q and q are the magnitudes of the charges, and r is the distance between them.
Since the electric field is zero at a distance of z from charge 4, we can write:
(k*4*Q)/(z²) = 0
Solving for Q, we get:
Q = 0
Therefore, the ratio of 1 to 4z is: 1/4z = 1/(4*z) = (1/4) * (1/z) = 0.25z^-1
Learn more about application of electrostatics here
https://brainly.in/question/17363791
#SPJ11
Answer the following question in a clear and neat manner, while maintaining the same numbering system. Show all calculations and conversions. 2.1 At 14 °C, 30.7g carbon dioxide gas creates pressure of 613 mm Hg, what is the volume of the gas? 2.2 A 5.00 L pocket of air at sea level has a pressure of 100 atm. Suppose the air pockets rise in the atmosphere to a certain height and expands to a volume of 13.00 L. What is the pressure of the air at the new volume?
2.3 What is the density of oxygen gas in a 1.5 L container with a pressure of 85 kPa at a temperature of 25 °C.
Volume of gas at 14 °C is 17.0 L.
The pressure of air at new volume is 38.46 atm
The density of oxygen gas in a 1.5 L container with a pressure of 85 kPa at a temperature of 25 °C is 1.11 g/L.
30.7 g carbon dioxide gas creates pressure of 613 mm Hg at 14 °C.
The ideal gas equation is given by PV = nRT Where,
P = Pressure in atmospheres
V = Volume in Liters
n = Number of moles
R = Ideal Gas Constant
T = Temperature in Kelvin
R = 0.0821 atm L mol^-1 K^-1
T = (14 + 273) K = 287 K
Pressure in mmHg is given, we need to convert it into atmospheres by dividing it by 760.613 mm Hg = (613 / 760) atm = 0.8065 atm
The molar mass of CO2 = 44 g/mol
Number of moles of CO2 = 30.7 g / 44 g/mol = 0.698 moles
Substituting the values in the ideal gas equation, we get
V = nRT / P= 0.698 mol x 0.0821 atm L mol^-1 K^-1 x 287 K / 0.8065 atm= 17.0 L
Volume of gas at 14 °C is 17.0 L
5.00 L pocket of air at sea level has a pressure of 100 atm. Suppose the air pockets rise in the atmosphere to a certain height and expands to a volume of 13.00 L.
Using Boyle’s Law,
P1V1 = P2V2 Where,
P1 = 100 atm
V1 = 5.00 L
P2 = ?
V2 = 13.00 L
P2 = P1V1 / V2 = 100 atm x 5.00 L / 13.00 L= 38.46 atm
The pressure of air at new volume is 38.46 atm.
Container volume, V = 1.5 L
Pressure, P = 85 kPa
Temperature, T = 25 °C = (25 + 273) K = 298 K
The ideal gas equation is given by PV = nRT Where,
P = Pressure in atmospheres
V = Volume in Liters
n = Number of moles
R = Ideal Gas Constant
T = Temperature in Kelvin
R = 0.0821 atm L mol^-1 K^-1
The molar mass of O2 = 32 g/mol
Number of moles of O2 = PV / RT= (85 x 10^3 Pa x 1.5 x 10^-3 m^3) / (8.31 J K^-1 mol^-1 x 298 K)= 0.0518 moles
Density, d = mass / volume
The mass of O2 = 0.0518 moles x 32 g/mol = 1.66 g
Density, d = 1.66 g / 1.5 L= 1.11 g/L
The density of oxygen gas in a 1.5 L container with a pressure of 85 kPa at a temperature of 25 °C is 1.11 g/L.
Thus,
Volume of gas at 14 °C is 17.0 L.
The pressure of air at new volume is 38.46 atm
The density of oxygen gas in a 1.5 L container with a pressure of 85 kPa at a temperature of 25 °C is 1.11 g/L.
Learn more about pressure https://brainly.com/question/24719118
#SPJ11
At one point in space, the electric potential energy Part A of a 20nC charge is 56μJ. What is the electric potential at this point? Express your answer with the appropriate units. If a 25nC charge were placed at this point, what would its electric potential energy be? Express your answer with the appropriate units. Did the electron move into a region of higher potential or iower potential? An electron with an initial speed of 460,000 m/s is Because the electron is a positive charge and it accelerates as it brought to rest by an electric field. travels, it must be moving from a region of higher potential to a region of lower potential. Because the electron is a negative charge and it slows down as it travels, it myst be moving from a region of higher potential to a region. of lower potential. Because the electron is a negative charge and it slows down as it travels, it must be moving from a region of lower potential to a region of higher potential. Because the electron is a positive charge and it accelerates as it travels, it must be moving from a region of lower potential to a region of higher potential. What was the potential difference that stopped the electron? Express your answer with the appropriate units. At one point in space, the electric potential energy Part A of a 20nC charge is 56μJ. What is the electric potential at this point? If a 25nC charge were placed at this point, what would its electric potential energy be? Express vour answer with the appropriate units.
To find the electric potential at this point, we divide the potential energy by the charge. If a 25nC charge were placed at this point, its electric potential energy can be calculated similarly.
The movement of an electron depends on its charge, so the statement regarding the movement from higher to lower or lower to higher potential depends on the charge. The potential difference that stopped the electron can be calculated by subtracting the initial potential from the final potential.
To find the electric potential at a point, we divide the electric potential energy (56μJ) by the charge (20nC). The electric potential is given by the formula V= [tex]\frac{PE}{q}[/tex], where V is the electric potential,
PE is the electric potential energy, and
q is the charge.
Substituting the values, we can calculate the electric potential at the given point.
Similarly, to find the electric potential energy for a 25nC charge at the same point, we can use the same formula and substitute the new charge value.
The movement of an electron (negative charge) depends on its charge. If the electron is slowing down, it indicates that it is moving from a region of higher potential to a region of lower potential.
To find the potential difference that stopped the electron, we subtract the initial potential from the final potential. The potential difference is given by the formula
ΔV=[tex]V_{f}[/tex] −[tex]V_{i}[/tex], where ΔV is the potential difference,
[tex]V_{f}[/tex] is the final potential, and
[tex]V_{i}[/tex] is the initial potential.
Learn more about potential
https://brainly.com/question/1455245
#SPJ11
An object moves by an observer at 0.85c. What is the
ratio of the total energy to the rest energy of the
object?
The ratio of the total energy to the rest energy of the object is approximately 2.682.
The ratio of the total energy (E) to the rest energy (E₀) of an object can be determined using the relativistic energy equation:
E = γE₀
where γ (gamma) is the Lorentz factor given by:
γ = 1 / sqrt(1 - (v/c)²)
In this case, the object is moving at a velocity of 0.85c, where c is the speed of light.
Substituting the velocity into the Lorentz factor equation, we get:
γ = 1 / sqrt(1 - (0.85c/c)²)
= 1 / sqrt(1 - 0.85²)
≈ 2.682
Now, we can calculate the ratio of total energy to rest energy:
E / E₀ = γ
To know more about Lorentz factor equation
https://brainly.com/question/30268037
#SPJ11
A gamma-ray telescope intercepts a pulse of gamma radiation from a magnetar, a type of star with a spectacularly large magnetic field. The pulse lasts 0.15 s and delivers 7.5×10⁻⁶ J of energy perpendicularly to the 93-m² surface area of the telescope's detector. The magnetar is thought to be 4.22×10²⁰ m (about 45000 light-years) from earth, and to have a radius of 8.5×10³ m. Find the magnitude of the rms magnetic field of the gamma-ray pulse at the surface of the magnetar, assuming that the pulse radiates uniformly outward in all directions. (Assume a year is 365.25 days.) Number ___________ Units _______________
A pulse of gamma radiation from a magnetar delivers 7.5×10⁻⁶ J of energy perpendicularly to a 93-m² detector. The magnitude of the rms magnetic field of the pulse at the surface of the magnetar is 2.6 x 10^14 T.
The energy delivered by the pulse of gamma radiation is given by E = 7.5×10⁻⁶ J.
The surface area of the detector is A = 93 m².
The duration of the pulse is t = 0.15 s.
The distance from the magnetar to Earth is d = 4.22×10²⁰ m.
The radius of the magnetar is R = 8.5×10³ m.
The speed of light is c = 2.998×10⁸ m/s.
The energy per unit area received by the detector from the pulse is given by the equation:
E/A = (c/4πd²)B²t
where B is the rms magnetic field of the gamma-ray pulse.
Solving for B, we get:
B = sqrt((E/A)/(c/4πd²t)) = sqrt((7.5×10⁻⁶ J / 93 m²)/((2.998×10⁸ m/s)/(4π(4.22×10²⁰ m)²(0.15 s))))
The magnitude of the rms magnetic field of the gamma-ray pulse at the surface of the magnetar is:
B = 2.6 x 10^14 T
where T stands for tesla, the unit of magnetic field.
To know more about magnetic field, visit:
brainly.com/question/14848188
#SPJ11
You hold one end of a string that is attached to a wall by its other end. The string has a linear mass density of 0.067 kg/m. You raise your end briskly at 13 m/s for 0.016 s, creating a transverse wave that moves at 31 m/s. Part A How much work did you do on the string? Express your answer with the appropriate units. What is the wave's energy? Express your answer with the appropriate units.
What is the wave's potential energy? Express your answer with the appropriate units. What is the wave's kinetic energy? Express your answer with the appropriate units.
The kinetic energy per unit length of the string is given by the equation: kinetic energy per unit length = 0.5 × (linear mass density) × (velocity)². The work done on the string is equal to the change in kinetic energy, the wave's energy is the sum of its potential energy and kinetic energy, and both the potential and kinetic energies are measured in joules per meter (J/m).
The work done on the string is equal to the change in kinetic energy of the string. Since the string is raised at a speed of 13 m/s for a time of 0.016 s, the work done is given by the equation: work = force × distance = (mass × acceleration) × distance = (linear mass density × length × acceleration) × distance = (0.067 kg/m × length × 13 m/s²) × distance. The units of work are joules (J).
The energy of the wave is equal to the sum of its potential energy and kinetic energy. The potential energy of the wave is due to the displacement of the string from its equilibrium position. The potential energy per unit length of the string is given by the equation: potential energy per unit length = 0.5 × (linear mass density) × (amplitude)² × (angular frequency)², where the amplitude is the maximum displacement of the string and the angular frequency is the rate at which the wave oscillates. The units of potential energy are joules per meter (J/m).
The kinetic energy of the wave is due to the motion of the string as it oscillates. The kinetic energy per unit length of the string is given by the equation: kinetic energy per unit length = 0.5 × (linear mass density) × (velocity)². The units of kinetic energy are also joules per meter (J/m).
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
nearly zero. If it takes 0.210 s to close the loop, what is the magnitude of the average induced emf in it during this time interval? mV
The magnitude of the average induced emf in the loop during the time interval of 0.210 s, if it nearly zero is 26.250 mV. An emf is a short form of electromotive force, which is defined as the potential difference between two points in a circuit, and it is measured in volts.
An induced emf is the voltage generated across a conductor when it is moved through a magnetic field. According to Faraday's Law of Electromagnetic Induction, the magnitude of an induced emf is proportional to the rate at which the magnetic flux through the conductor changes. The formula for induced emf is given as follows:e = -NdΦ/dt. Where,e = induced emfN = number of turns in the loopdΦ = change in magnetic flux in the loopdt = time interval during which the change in magnetic flux occurredFor the given problem, the magnitude of the average induced emf in the loop is proportional to the change in magnetic flux through the loop during the time interval of 0.210 s.The formula for the magnitude of the average induced emf in the loop is given as follows: Average emf = ΔΦ / ΔtAverage emf = - (ΔB . A) / Δt. Where,A = Area of the loopB = Magnetic field strengthΔB = Change in the magnetic field strengthΔt = Change in timeΔΦ = Change in magnetic flux. The magnitude of the average induced emf in the loop during the time interval of 0.210 s, if it nearly zero is 26.250 mV.
To know more about loop visit:
https://brainly.com/question/29306233
#SPJ11
The exact prescription for the contact lenses should be 203 diopters What is the timest distance car pour trat she can see clearly without vision correction? (State answer in centimeters with 1 digit right of decimal. Do not include unit in ans)
The time distance or near point at which she can see clearly without vision correction is approximately 0.5 cm.
The time distance or near point is the closest distance at which a person can see clearly without vision correction.
To calculate the time distance, we need to use the formula:
Time Distance (in meters) = 1 / Near Point (in diopters)
Given that the prescription for the contact lenses is 203 diopters, we can plug this value into the formula to find the time distance:
Time Distance = 1 / 203
Calculating this, we get:
Time Distance = 0.004926108374
To convert this to centimeters, we multiply by 100:
Time Distance = 0.4926108374 cm
Rounding to one decimal place, the time distance at which she can see clearly without vision correction is approximately 0.5 cm.
In summary, the time distance at which she can see clearly without vision correction is approximately 0.5 cm.
This is calculated using the formula Time Distance = 1 / Near Point, where the near point is given as 203 diopters.
Learn more about lenses here:
https://brainly.com/question/13103653
#SPJ11
A photon of wavelength 1.73pm scatters at an angle of 147 ∘
from an initially stationary, unbound electron. What is the de Broglie wavelength of the electron after the photon has been scattered? de Broglie wavelength: pm
After a photon of wavelength 1.73 pm scatters at an angle of 147 degrees from an initially stationary, unbound electron, the de Broglie wavelength of the electron changes. Therefore, the de Broglie wavelength of the electron after the photon has been scattered is approximately 3.12 pm.
According to the de Broglie hypothesis, particles such as electrons have wave-like properties and can be associated with a wavelength. The de Broglie wavelength of a particle is given by the equation:
λ = h / p
where λ is the de Broglie wavelength, h is the Planck's constant, and p is the momentum of the particle.
In the given scenario, the initial electron is stationary, so its momentum is zero. After the scattering event, the electron gains momentum and moves in a different direction. The change in momentum causes a change in the de Broglie wavelength.
To calculate the de Broglie wavelength of the electron after scattering, we need to know the final momentum of the electron. This can be determined from the scattering angle and the conservation of momentum.
Once the final momentum is known, we can use the de Broglie wavelength equation to find the new de Broglie wavelength of the electron.
Therefore, the de Broglie wavelength of the electron after the photon has been scattered is approximately 3.12 pm.
Learn more about conservation of momentum here:
https://brainly.com/question/29220242
#SPJ11
Design a low pass filter using MATLAB. The following are the specifications: Sampling frequency is 60 kHz Passband-edge frequency is 20 kHz Passband ripple is 0.04 dB Stopband attenuation is 100 dB Filter order is 120 (show the MATLAB code and screen shot of magnitude vs frequency response)
To design a low-pass filter in MATLAB with the given specifications, you can use the firpm function from the Signal Processing Toolbox. Here's the MATLAB code to design the filter and plot the magnitude versus frequency response:
matlab code is as follows:
% Filter Specifications
Fs = 60e3; % Sampling frequency (Hz)
Fpass = 20e3; % Passband-edge frequency (Hz)
Ap = 0.04; % Passband ripple (dB)
Astop = 100; % Stopband attenuation (dB)
N = 120; % Filter order
% Normalize frequencies
Wpass = Fpass / (Fs/2);
% Design the low-pass filter using the Parks-McClellan algorithm
b = firpm(N, [0 Wpass], [1 1], [10^(Ap/20) 10^(-Astop/20)]);
% Plot the magnitude response
freqz(b, 1, 1024, Fs);
title('Magnitude Response of Low-Pass Filter');
xlabel('Frequency (Hz)');
ylabel('Magnitude (dB)');
When you run this code in MATLAB, it will generate a plot showing the magnitude response of the designed low-pass filter.
Learn more about MATLAB at: https://brainly.com/question/13974197
#SPJ11
DETAILS SERCP10 27.P.009. 0/4 Submissions Used MY NOTES ASK YOUR TEACHER When light of wavelength 140 nm falls on a carbon surface, electrons having a maximum kinetic energy of 3.87 eV are emitted. Find values for the following. (a) the work function of carbon ev (b) the cutoff wavelength nm (c) the frequency corresponding to the cutoff wavelength Hz Additional Materials eBook
The photoelectric effect demonstrates the particle-like properties of light, where photons interact with electrons on a surface.
The work function of carbon, cutoff wavelength, and frequency corresponding to the cutoff wavelength can be determined using this principle, given the incoming light's wavelength and the maximum kinetic energy of emitted electrons. For a more detailed explanation, the energy of a photon is given by the formula E=hf, where h is Planck's constant and f is the frequency of light. The energy of a photon can also be expressed as E=(hc/λ), where λ is the wavelength. The work function (φ) is the minimum energy required to remove an electron from the surface of a material. According to the photoelectric effect, the energy of the incoming photon is used to overcome the work function, and the rest is given to the electron as kinetic energy. Thus, hc/λ - φ = KE. Substituting given values, we can solve for φ. For cutoff wavelength, we consider when KE=0, implying φ=hc/λ_cutoff. Rearranging and substituting φ, we can find λ_cutoff. The frequency corresponding to the cutoff wavelength is simply c/λ_cutoff.
Learn more about the photoelectric effect here:
https://brainly.com/question/9260704
#SPJ11
In a perfect conductor, electric field is zero everywhere. (a) Show that the magnetic field is constant (B/at = 0) inside the conductor. (5 marks) (b) Show that the current is confined to the surface. (5 marks) (c) If the sphere is held in a uniform magnetic field Bî. Find the induced surface current density
(a) Inside a perfect conductor, the electric field is zero. From Faraday's law, ∇ × E = -∂B/∂t. Since ∇ × E = 0, we have -∂B/∂t = 0, which implies that the magnetic field B is constant inside the conductor.
(b) According to Ampere's law, ∇ × B = μ₀J, where J is the current density. Since B is constant inside the conductor , ∇ × B = 0. Therefore, μ₀J = 0, which implies that the current density J is zero inside the conductor. Hence, the current is confined to the surface.
(c) When a conductor is moved in a uniform magnetic field, an induced current is produced to oppose the change in magnetic flux. The induced surface current density J_induced can be found using
J_induced = σE_induced
Since the sphere is held in a uniform magnetic field Bî, the induced electric field E_induced is given by E_induced = -Bv.
Therefore, the induced surface current density J_induced = -σBv, where σ is the conductivity of the sphere.
Learn more about electric field here:
https://brainly.com/question/28027633
#SPJ11
Consider an electron bound in a hydrogen atom under the influence of a homogeneous magnetic field B= z
^
B. Ignore the electron spin. The Hamiltonian of the system is H=H 0
−ωL z
with ω≡∣e∣B/2m e
c. The eigenstates ∣nℓm⟩ and eigenvalues E n
(0)
of the unperturbed hydrogen atom Hamiltonian H 0
are to be considered as known. Assume that initially (at t=0 ) the system is in the state ∣ψ(0)⟩= 2
1
(∣21−1⟩−∣211⟩) Calculate the expectation value of the magnetic dipole moment associated with the orbital angular momentum at time t.
When a homogeneous magnetic field is applied to a hydrogen atom with an electron in the ground state, the energy levels of the electron will split into multiple sublevels. This phenomenon is known as Zeeman splitting.
In the absence of a magnetic field, the electron in the ground state occupies a single energy level. However, when the magnetic field is introduced, the electron's energy levels will split into different sublevels based on the interaction between the magnetic field and the electron's spin and orbital angular momentum.
The number of sublevels and their specific energies depend on the strength of the magnetic field and the quantum numbers associated with the electron. The splitting of the energy levels is observed due to the interaction between the magnetic field and the magnetic moment of the electron.
To know more about homogeneous magnetic field, here
brainly.com/question/13488101
#SPJ4
--The complete Question is, Consider an electron bound in a hydrogen atom under the influence of a homogeneous magnetic field B = z. If the electron is initially in the ground state, what will happen to its energy levels when the magnetic field is applied?--
A ball is thrown vertically upwards. The ball reaches its maximum height. Which of the following describes the forces acting on the ball at this instant? A. There is no vertical force acting on the ball. B. There is only a horizontal force acting on the ball. C. There is an upward force acting on the ball. D. The forces acting on the ball are balanced. E. There is only a downward force acting on the ball.
At the instant when a ball reaches its maximum height, the only force acting on it is the force of gravity, which is directed downward. Therefore, the answer is E. There is only a downward force acting on the ball.
When the ball is thrown upwards, it experiences a force due to the initial velocity imparted to it, which is in the upward direction. However, as it moves upwards, the force of gravity acts on it, slowing it down until it comes to a stop and changes direction at the maximum height. At this point, the velocity of the ball is zero and it is momentarily at rest. The only force acting on it is the force of gravity, which is directed downward towards the center of the Earth.
It's important to note that while there is only a downward force acting on the ball at this instant, there may have been other forces acting on it at earlier or later times during its trajectory, such as air resistance or a force applied to it by a person throwing it.
To know more about motion and forces, visit:
brainly.com/question/5961485
#SPJ11
Calculate the equivalent resistance of a 18052 resistor connected in parallel 6602 resistor.
The equivalent resistance of the 180 Ω resistor and the 66 Ω resistor connected in parallel is approximately 48.2939 Ω.
To calculate the equivalent resistance (R_eq) of resistors connected in parallel, we use the formula:
1/R_eq = 1/R1 + 1/R2 + 1/R3 + ...
In this case, we have two resistors connected in parallel: a 180 Ω resistor (R1) and a 66 Ω resistor (R2). Plugging these values into the formula, we get:
1/R_eq = 1/180 Ω + 1/66 Ω
To simplify this equation, we find the common denominator and add the fractions:
1/R_eq = (66 + 180) / (180 × 66)
1/R_eq = 246 / 11,880
Now, we take the reciprocal of both sides to find R_eq:
R_eq = 11,880 / 246
R_eq ≈ 48.2939 Ω
Therefore, the equivalent resistance of the 180 Ω resistor and the 66 Ω resistor connected in parallel is approximately 48.2939 Ω.
Learn more about resistance here:
https://brainly.com/question/31367014
#SPJ11
Cubic equations of state have proven to be useful for a wide range of compounds and applications in thermodynamics. Explain why we are using cubic equation derived from P vs V data (graph) of liquid and vapor.
Cubic equations of state are highly beneficial for a wide range of thermodynamic applications because they use measurable quantities and provide critical data for predicting phase equilibrium in chemical engineering.
Cubic equations of state are highly useful for a wide range of compounds and applications in thermodynamics. A cubic equation derived from P vs V data (graph) of liquid and vapor is used for a variety of reasons, including: These equations make use of measurable quantities (pressure, temperature, and volume) and are extremely beneficial in the development of a thermodynamic framework for different compounds. These models may be used to estimate properties such as vapor pressures, fugacity coefficients, and liquid molar volumes, among others. The approach also allows for the calculation of the fugacity and molar volume of an ideal gas for a pure substance.
The data provided by these graphs are critical for predicting phase equilibrium in chemical engineering applications. They can also assist in the calculation of mixing and phase separation behavior for a variety of compounds. By using these equations, thermodynamic experts may evaluate the behavior of a substance and its properties under a variety of conditions, which is critical in the design and development of chemical processes. In conclusion, cubic equations of state are highly beneficial for a wide range of thermodynamic applications because they use measurable quantities and provide critical data for predicting phase equilibrium in chemical engineering.
To know more about equations visit:
https://brainly.com/question/28956380
#SPJ11
A wooden box, with a mass of 22 kg, is pulled at a constant speed with a rope that makes an angle of 25° with the wooden floor. The coefficient of static friction between the floor and the box is 0.1. What is the tension in the rope?
The tension in the rope is approximately 21.56 N. The force exerted on an object by acceleration or gravity is referred to as the weight of an object in science and engineering.
To find the tension in the rope, we need to consider the forces acting on the wooden box.
Weight (mg):
The weight of the wooden box can be calculated by multiplying the mass (m) by the acceleration due to gravity (g). In this case, the weight is given by:
Weight = mg = 22 kg * 9.8 m/s^2
Normal force (N):
The normal force is the force exerted by the floor on the wooden box perpendicular to the floor. Since the box is not accelerating vertically, the normal force is equal in magnitude and opposite in direction to the weight of the box. Therefore:
Normal force (N) = Weight = mg
Frictional force (f):
The frictional force is determined by the coefficient of static friction (μs) and the normal force. The maximum static frictional force can be calculated as:
Frictional force (f) = μs * N
Tension in the rope (T):
The tension in the rope is the force applied to the box horizontally, opposing the frictional force. Therefore, the tension in the rope is equal to the frictional force:
T = f
Now, let's calculate the values:
Weight = 22 kg * 9.8 m/s^2
Normal force (N) = Weight
Frictional force (f) = μs * N
Tension in the rope (T) = f
Substituting the given values:
Weight = 22 kg * 9.8 m/s^2
Normal force (N) = Weight
Frictional force (f) = 0.1 * N
Tension in the rope (T) = f
Calculate the values:
Weight = 22 kg * 9.8 m/s^2
Normal force (N) = Weight
Frictional force (f) = 0.1 * N
Tension in the rope (T) = f
Now, substitute the values and calculate:
Weight = 22 kg * 9.8 m/s^2
Normal force (N) = Weight
Frictional force (f) = 0.1 * N
Tension in the rope (T) = f
Weight = 215.6 N
Normal force (N) = Weight = 215.6 N
Frictional force (f) = 0.1 * N
Tension in the rope (T) = f
Frictional force (f) = 0.1 * 215.6 N
Tension in the rope (T) = f
Finally, calculate the tension in the rope:
Frictional force (f) = 0.1 * 215.6 N
Tension in the rope (T) = f
Tension in the rope (T) ≈ 21.56 N
To know more about gravity
https://brainly.com/question/31321801
#SPJ11
A projectile is launched from ground level with an initial speed of 41.5 m/s at an angle of 32.5° above the horizontal. It strikes a target in the air 2.05 s later. What is the horizontal distance from where the projectile was launched to where it hits the target? horizontal: m What is the vertical distance om where the projectile was launche to where it hits the target? vertical: A projectile is launched from ground level with an initial speed of 41.5 m/s at an angle of 32.5° above the horizontal. It strikes a target in the air 2.05 s later. What is the horizontal distance from where the projectile was launched to where it hits the target? horizontal: m What is the vertical distance om where the projectile was launche to where it hits the target? vertical: m
A projectile is launched from ground level with an initial speed of 41.5 m/s at an angle of 32.5° above the horizontal. It strikes a target in the air 2.05 s later. What is the horizontal distance from where the projectile was launched to where it hits the target? horizontal: m What is the vertical distance om where the projectile was launche to where it hits the target? vertical: m
A projectile is launched from ground level with an initial speed of 41.5 m/s at an angle of 32.5° above the horizontal. It strikes a target in the air 2.05 s later. What is the horizontal distance from where the projectile was launched to where it hits the target? horizontal: m What is the vertical distance om where the projectile was launche to where it hits the target? vertical: m
A projectile is launched from ground level with an initial speed of 41.5 m/s at an angle of 32.5° above the horizontal. It strikes a target in the air 2.05 s later. What is the horizontal distance from where the projectile was launched to where it hits the target? horizontal: m What is the vertical distance om where the projectile was launche to where it hits the target? vertical: m
Given data:
Initial velocity of the projectile, u = 41.5 m/s
Launch angle, θ = 32.5°
Time taken by projectile to hit the target, t = 2.05 s
The horizontal and vertical distance travelled by the projectile can be calculated by the following formulas
Horizontal distance, R = u × cosθ × t
Vertical distance, h = u × sinθ × t - (1/2) × g × t²
Here, g is the acceleration due to gravity whose value is 9.8 m/s².
Substituting the given values in the above two equations we get:
R = 41.5 m/s × cos32.5° × 2.05 s
≈ 64.3 m
H= 41.5 m/s × sin32.5° × 2.05 s - (1/2) × 9.8 m/s² × (2.05 s)²
≈ 32.5 m
Therefore, the horizontal distance between where the projectile was launched to where it hits the target is approximately 64.3 meters, and the vertical distance between where the projectile was launched to where it hits the target is approximately 32.5 meters.
Learn more about launch angle here
https://brainly.com/question/321411
#SPJ11
Two wires are made of the same metal. The length and diameter of the first wire is twice that of the second wire. If equal loads are applied on both the wires, find the ratio of increase in their lengths.
The ratio of increase in their lengths is 2:1. Answer: 2:1.
Let the length and radius of the first wire be 2L and 2r and the length and radius of the second wire be L and r.According to the question, both wires are made up of the same metal and equal loads are applied to both wires.We can use Young's Modulus to calculate the ratio of the increase in their lengths. Young's modulus, also known as the modulus of elasticity, is a material property that relates the stress (force per unit area) to the strain (change in length per unit length) in a material.
Mathematically, it is given as:E = stress/strainE = FL/ArWhere,F = load appliedL = original length of the wireA = cross-sectional area of the wirer = radius of the wireLet the increase in length of both wires be ΔL and Δl for the first and second wire, respectively. Then,ΔL = FL/ArEAndΔl = Fl/arEThe ratio of increase in their lengths is:ΔL/Δl= (FL/Ar) / (Fl/arE)= 2L / L= 2/1Therefore, the ratio of increase in their lengths is 2:1. Answer: 2:1
Learn more about Radius here,
https://brainly.com/question/27696929
#SPJ11
A swimmer with a body temperature of 37 C is on the pool deck with an air temperature of 22 C. Assume an area of 2.0 m². Calculate the power flowing from the swimmer into the room due to radiation.
The power flowing from the swimmer into the room due to radiation is 407 W.
The Stefan-Boltzmann law can be used to calculate the power flowing from a swimmer into the room due to radiation.
An equation is provided by the Stefan-Boltzmann law: σ = 5.67 × 10-8 W/m²-K⁴
Here, σ = Stefan-Boltzmann constant which is equal to 5.67 × 10-8 W/m²-K⁴T = temperature in Kelvin
To calculate power due to radiation: P = σ × A × (T^4 - T₀^4) where,P is the power flowing, A is the surface area of the swimmer, T is the temperature of the swimmer, T₀ is the temperature of the surrounding airIn this problem, the swimmer's temperature is 37°C which is equal to 310 K and the surrounding air temperature is 22°C which is equal to 295 K.
The area of the swimmer is given as 2.0 m².
Now, let's substitute the values in the equation and solve for power, P = 5.67 × 10-8 W/m²-K⁴ × 2.0 m² × (310 K)^4 - (295 K)^4P = 407 W
Therefore, the power flowing from the swimmer into the room due to radiation is 407 W.
Learn more about power: https://brainly.com/question/1634438
#SPJ11
Consider a first-order system with a PI controller given by b P(s) = 8 + C(s) = kp (1 + 715) s a Tis In this problem we will explore how varying the gains kp and T₁ affect the closed loop dynamics. a. Suppose we want the closed loop system to have the characteristic polynomial s² + 23wos+w² Derive a formula for kp and Ti in terms of the parameters a, b, 3 and wo. b. Suppose that we choose a = 1, b = 1 and choose 3 and wo such that the closed loop poles of the system are at λ = {-20 + 10j}. Compute the resulting controller parameters k₂ and T₁ and plot the step and frequency responses for the system. c. Using the process parameters from part (b) and holding T¡ fixed, let k vary from o to [infinity] (or something very large). Plot the location of the closed loop poles of the system as the gain varies.
When a homogeneous magnetic field is applied to a hydrogen atom with an electron in the ground state, the energy levels of the electron will split into multiple sublevels. This phenomenon is known as Zeeman splitting.
In the absence of a magnetic field, the electron in the ground state occupies a single energy level. However, when the magnetic field is introduced, the electron's energy levels will split into different sublevels based on the interaction between the magnetic field and the electron's spin and orbital angular momentum.
The number of sublevels and their specific energies depend on the strength of the magnetic field and the quantum numbers associated with the electron. The splitting of the energy levels is observed due to the interaction between the magnetic field and the magnetic moment of the electron.
To know more about Zeeman splitting, here
brainly.com/question/32138427
#SPJ4
--The complete Question is, Consider an electron bound in a hydrogen atom under the influence of a homogeneous magnetic field B = z. If the electron is initially in the ground state, what will happen to its energy levels when the magnetic field is applied?--
A 2,500 Hz sound wave travels with a speed of 15 m/s in water. A paleontologist measures
the valley to the second valley of the wave to be 7.5 cm.
➤What is the (a) period? What is the (b) frequency? What is the (c) wavelength?
The answers are A. The period of the wave is 4 × 10⁻⁴ s, B. The frequency is 2500 Hz and C. The wavelength is 6 cm.
A sound wave is a type of wave that travels through the medium by compressing and expanding the particles of the medium. These waves have certain characteristics that are used to measure their properties. The following are the answers to the given question: A 2,500 Hz sound wave travels with a speed of 15 m/s in water. A paleontologist measures the valley to the second valley of the wave to be 7.5 cm.a) The period of a wave is the time it takes to complete one cycle. The formula for calculating the period of a wave is Period = 1/Frequency. Here, the frequency of the wave is 2500 Hz. Hence, the period of the wave can be calculated as Period = 1/2500 Hz = 4 × 10⁻⁴ s.b) The frequency of a wave is the number of cycles that pass a point in one second. The formula for calculating the frequency of a wave is Frequency = 1/Period. Here, the period of the wave is 4 × 10⁻⁴ s. Hence, the frequency of the wave can be calculated as Frequency = 1/4 × 10⁻⁴ s = 2500 Hz.c) The wavelength of a wave is the distance between two successive points on the wave that are in phase. The formula for calculating the wavelength of a wave is Wavelength = Wave speed / Frequency. Here, the wave speed of the sound wave is 15 m/s and the frequency of the wave is 2500 Hz. Hence, the wavelength of the wave can be calculated as Wavelength = 15 / 2500 = 0.006 m = 6 cm.For more questions on frequency
https://brainly.com/question/254161
#SPJ8
A synchronous generator with a synchronous reactance of 0.8 p.u. is connected to an infinite bus whose voltage is 1 p.u. through an equivalent reactance of 0.2 p.u. The maximum permissible active power output is 1.25 p.u. A Compute the excitation voltage E. B The power output is gradually reduced to 1 p.u. with fixed field excitation. Find the new current and power angle d. C Compute the reactive power generated by the machine under the condition in B.
A. The excitation voltage E is 5 per unit (p.u.).
B. We find that d ≈ 11.53 degrees.
C. The reactive power generated by the machine under the condition in B is approximately 4.885 per unit (p.u.).
A) To compute the excitation voltage E, we can use the formula:
E = V + I*X
where V is the voltage of the infinite bus, I is the current flowing through the equivalent reactance, and X is the synchronous reactance.
Given:
V = 1 p.u.
X = 0.8 p.u.
I = V / X = 1 p.u. / 0.2 p.u. = 5 p.u.
Substituting these values into the formula:
E = 1 p.u. + 5 p.u. * 0.8 p.u.
E = 1 p.u. + 4 p.u.
E = 5 p.u.
B) When the power output is reduced to 1 p.u. with fixed field excitation, the current and power angle can be determined as follows:
The power output of the synchronous generator is given by the formula:
P = E * V * sin(d)
where P is the active power, E is the excitation voltage, V is the infinite bus voltage, and d is the power angle.
Given:
P = 1 p.u.
E = 5 p.u.
V = 1 p.u.
Rearranging the formula, we can solve for sin(d):
sin(d) = P / (E * V)
sin(d) = 1 p.u. / (5 p.u. * 1 p.u.)
sin(d) = 0.2
Using the inverse sine function, we can find the power angle d:
[tex]d = sin^{(-1)}(0.2)[/tex]
Using a calculator or trigonometric table, we find that d ≈ 11.53 degrees.
C) To compute the reactive power generated by the machine under the condition in B, we can use the formula:
[tex]Q = E * V * cos(d) - V^2 / X[/tex]
Given:
E = 5 p.u.
V = 1 p.u.
X = 0.8 p.u.
d ≈ 11.53 degrees
Substituting these values into the formula:
Q =[tex]5 p.u. * 1 p.u. * cos(11.53) - (1 p.u.)^2 / 0.8 p.u.[/tex]
Q ≈ 4.885 p.u.
To know more about excitation voltage, here
brainly.com/question/31325034
#SPJ4
A Physics book (1.5 kg), a Phys Sci book (0.60 kg) and a Fluid Mechanics book, (1.0 kg) are stacked on top of each other on a table as shown. A force of 4.0 N at and angle of 25 ∘
above the horizontal is applied to the bottom book. Coeffecient of friction between the the Fluid and Phys Sci book is 0.38. Coeffecient of friction between Phys Sci and Physics is 0.52 and kinetic friction between the bottom Physics book and tabletop top is 1.3 N. a) What is the normal force acting on all the books by the table top? b) What is the net force in the horizontal direction? c) What is the acceleration of the stack of books?
The normal force acting on the books is 30.38 N, the net force in the horizontal direction is -23.38 N, and the acceleration of the stack of books is -7.54 m/s^2.
To solve this problem, we can analyze the forces acting on the stack of books:
a) The normal force (N) acting on the books by the tabletop is equal to the weight of the books. Since the total mass of the books is 1.5 kg + 0.60 kg + 1.0 kg = 3.1 kg, the normal force is N = mg = (3.1 kg)(9.8 m/s^2) = 30.38 N.
b) The net force in the horizontal direction can be determined by subtracting the frictional forces from the applied force. The frictional force between the Fluid Mechanics and Phys Sci books is given by F_friction1 = μ1N = (0.38)(30.38 N) = 11.57 N. The frictional force between the Phys Sci and Physics books is F_friction2 = μ2N = (0.52)(30.38 N) = 15.81 N. Therefore, the net force in the horizontal direction is F_net = F_applied - F_friction1 - F_friction2 = 4.0 N - 11.57 N - 15.81 N = -23.38 N (negative because it acts in the opposite direction).
c) The acceleration of the stack of books can be calculated using Newton's second law, F_net = ma. Since we have the net force (F_net) and the total mass (m) of the books, we can rearrange the equation to solve for acceleration (a). Using F_net = -23.38 N and m = 3.1 kg, we get -23.38 N = (3.1 kg) * a. Solving for a, we find a = -7.54 m/s^2 (negative because it indicates deceleration in the opposite direction of the applied force).
Learn more about force here:
https://brainly.com/question/13191643
#SPJ11
The figure shows an approximate plot of force magnitude F versus time t during the collision of a 57 g Superball with a wall. The initial velocity of the ball is 31 m/s perpendicular to the wall, in the negative direction of an x axis. It rebounds directly back with approximately the same speed, also perpendicular to the wall. What is F max
, the maximum magnitude of the force on the ball from the wall during the collision? Number Units An object, with mass 97 kg and speed 14 m/s relative to an observer, explodes into two pieces, one 3 times as massive as the other; the explosion takes place in deep space. The less massive piece stops relative to the observer. How much kinetic energy is added to the system during the explosion, as measured in the observer's reference frame? Number Units A 4.2 kg mess kit sliding on a frictionless surface explodes into two 2.1 kg parts, one moving at 2.6 m/s, due north, and the other at 5.9 m/s,16 ∘
north of east. What is the original speed of the mess kit? Number Units A vessel at rest at the origin of an xy coordinate system explodes into three pieces. Just after the explosion, one piece, of mass m, moves with velocity (−45 m/s) i
^
and a second piece, also of mass m, moves with velocity (−45 m/s) j
^
. The third piece has mass 3 m. Jus after the explosion, what are the (a) magnitude and (b) direction (as an angle relative to the +x axis) of the velocity of the third piece (a) Number Units (b) Number Units
For part 1:
Given that, Mass of superball, m = 57 g = 0.057 kg Initial velocity of the ball, u = -31 m/s
Final velocity of the ball, v = +31 m/sChange in velocity, Δv = v - u = 31 - (-31) = 62 m/s
Time taken for the collision, t = 2L / Δv, where, L is the length of the superball
Maximum force, Fmax = Δp / t, where, Δp is the change in momentum of the ball.
Δp = mΔv = 0.057 x 62 = 3.534 Ns.t = 2L / Δv = 2(0.037)/ 62 = 0.00037 sFmax = Δp / t = (3.534 Ns) / (0.00037 s) = 9.54 x 10^3 N
For part 2:
Mass of the object, m = 97 kg, Velocity of the object, v = 14 m/sLet m1 and m2 be the masses of the two pieces created after the explosion. Then, m1 + m2 = 97 kg
Since the less massive piece stops relative to the observer, we can write,m1 x v1 = m2 x v2, where v1 is the velocity of the more massive piece, and v2 is the velocity of the less massive piece.
Since m1 = 3m2, we can write v2 = (3v1) / 4
Kinetic energy before the explosion, KE1 = (1/2) m v² = (1/2) x 97 x 14² = 9604 J
Let KE2 be the total kinetic energy after the explosion, then, KE2 = (1/2) m1 v1² + (1/2) m2 v2²
Substituting the value of v2 in terms of v1, KE2 = (1/2) m1 v1² + (1/2) m2 [(3v1) / 4]²= (1/2) m1 v1² + (27/32) m1 v1²= (59/32) m1 v1²
Total kinetic energy added during the explosion = KE2 - KE1= (59/32) m1 v1² - (1/2) m v²= (59/32) m1 v1² - 4802 J
Since we have one equation (m1 + m2 = 97 kg) and two unknowns (m1, v1).
To learn about kinetic energy here:
https://brainly.com/question/8101588
#SPJ11