The magnitude of the induced emf in the coil at the instant the magnetic field has a magnitude of 50 mT is approximately 7.64 V.
Number of turns = 191
Radius = 9 cm = 0.09 m
Initial magnetic field = 20 mT
Final magnetic field = 80 mT
Time = 2 ms = 2 x 10^-3 s
The induced emf in the coil is given by Faraday's law:
ε = -N∆B/∆t
where ε is the induced emf, N is the number of turns, ∆B is the change in magnetic field, and ∆t is the time interval.
Substituting the given values, we get:
ε = -191 × (80 - 20) mT / 2 x 10^-3 s
ε = -7640 mT/s
The magnitude of the induced emf is 7640 mV. Rounding to two decimal places, we get:
ε = 7640.0 mV = 7.64 V
Therefore, the magnitude of the induced emf in the coil at the instant the magnetic field has a magnitude of 50 mT is 7.64 V.
Learn more about induced emf https://brainly.com/question/13744192
#SPJ11
Momentum uncertainty [5 points] Show that in a free-particle wave packet the momentum uncertainty Ap does not change in time. 7. Finding Meaning in the Phase of the Wavefunction [10 points] Suppose (x) is a properly-normalized wavefunction with (x). = x, and (p). = Po, where to and Po are constants. Define the boost operator Bą to be the operator that acts on arbitrary functions of x by multiplication by a q-dependent phase: Bq f(x) = eiqx/h f(x). Here q is a real number with the appropriate units. Consider now a new wavefunction obtained by boosting the initial wavefunction: Vnew(x) = B₁ Vo(x). (a) What is the expectation value (x)new in the state given by new (x)? What is the expectation value (p) new in the state given by new (x)? (c) Based on your results, what is the physical significance of adding an overall factor eiqx/h to a wavefunction. (d) Compute [p, Ba] and [2, B₂].
The momentum uncertainty Ap does not change in time in a free-particle wave packet.The wave packet's momentum uncertainty Ap doesn't change in time because the wave packet disperses with time, making its spread larger. To have an unchanging momentum uncertainty, the product of the spread in position and the spread in momentum should stay constant.
The wave function at t=0 is given by φ(x) = (2/a)^(1/2) sin (πx/a)
It can be calculated that the momentum expectation value p(x) for this wave function is 0. This is also true for all subsequent time periods. If the momentum is calculated with uncertainty, it will be observed that it is unchanging in time, meaning that the uncertainty in the momentum is unchanging in time.
Let us solve the remaining question:
Given that wave function x is normalized and (x) = x, and (p) = Po is constant.
The boost operator can be defined as:
Bq f(x) = eiqx/h f(x), where q is a real number with the appropriate units.
Now, consider a new wave function obtained by boosting the initial wave function:
Vnew(x) = B1 Vo(x).
The expectation value (x)new in the state given by new (x) is:
xnew = [(x)B1 V(x)] / (B1 V(x)) = (x) + q/h
The expectation value (p)new in the state given by new (x) is:
pnew = [(p)B1 V(x)] / (B1 V(x)) = (p) + q
Based on the results, the physical significance of adding an overall factor eiqx/h to a wave function is to displace the position of the wave function by an amount proportional to q/h and the momentum by an amount proportional to q. Hence, this factor represents a uniform motion in the x-direction with
speed v = q/h.(p, B1)
= - iq/h B1, [x, B1]
= h/i B1.
Learn more about uniform motion here
https://brainly.com/question/29029651
#SPJ11
(b) Estimate the pressure on the mountains underneath the Antarctic ice sheet, which is typically 3 km thick. (Density of ice = 917 kg/m³, g = 9.8 m/s²) Pressure 9170009
The estimated pressure on the mountains underneath the Antarctic ice sheet is approximately 26,854,200 N/m². To estimate the pressure on the mountains underneath the Antarctic ice sheet, we can use the formula for pressure:
Pressure = Density * g * Depth
Given:
Density of ice (ρ) = 917 kg/m³
Acceleration due to gravity (g) = 9.8 m/s²
Depth of the ice sheet (h) = 3 km = 3000 m
Plugging in these values into the formula, we get:
Pressure = 917 kg/m³ * 9.8 m/s² * 3000 m
= 26,854,200 N/m²
Therefore, the estimated pressure on the mountains underneath the Antarctic ice sheet is approximately 26,854,200 N/m².
To know more about Acceleration
brainly.com/question/31946450
#SPJ11
A cannon ball is launched into the ocean at an angle of 30° above the horizon. The cannonball has an initial speed of 46 m/s. The deck the cannonball is fired from is 11 meters high assume this is the initial height of the cannonball). a.) How long does the cannon ball take to reach the ocean? b.) What is the speed of the cannonball just before it lands in the ocean?
The speed of the cannon ball just before it lands in the ocean is given bythe resultant of the horizontal and vertical componentsv = √(vx² + vf²) = √(23 (√3)² + 32.32²)= √(1588.08) = 39.85 m/sHence, the speed of the cannon ball just before it lands in the ocean is 39.85 m/s.
a.) Time taken by the cannon ball to reach the ocean:The initial velocity of the cannon ball, u = 46 m/sThe angle made by the cannon ball with the horizontal, θ = 30°The vertical component of the initial velocity, v = u × sin θ = 46 × sin 30°= 46/2 = 23 m/sLet the time taken by the cannon ball to reach the ocean be t seconds.The distance covered by the cannon ball in the vertical direction in time t is given byh = ut + 1/2gt²where, g = acceleration due to gravity = 9.8 m/s²Substituting the values,11 = (23)t - 1/2 × 9.8 × t²11 = 23t - 4.9t²On solving this equation, we get two values of t, t = 0.947 seconds or t = 4.795 secondsThe time taken by the cannon ball to reach the ocean is 0.947 seconds.
b.) The speed of the cannonball just before it lands in the ocean:The horizontal component of the initial velocity of the cannon ball,vx = u × cos θ = 46 × cos 30°= 46(√3)/2 = 23 (√3) m/sThe time taken by the cannon ball to reach the ocean, t = 0.947 secondsThe horizontal distance covered by the cannon ball in time t is given byx = vx × t = 23 (√3) × 0.947 = 21.04 mThe vertical component of the final velocity of the cannon ball just before it lands in the ocean,vf = u + gt = 23 + 9.8 × 0.947 = 32.32 m/s
The speed of the cannon ball just before it lands in the ocean is given bythe resultant of the horizontal and vertical componentsv = √(vx² + vf²) = √(23 (√3)² + 32.32²)= √(1588.08) = 39.85 m/sHence, the speed of the cannon ball just before it lands in the ocean is 39.85 m/s.
Learn more about Speed here,
https://brainly.com/question/13943409
#SPJ11
True or false: If your reverse the direction of charge motion and magnetic field without changing the polarity of the charge, the direction of force changes.
True. According to the right-hand rule, the direction of the force on a moving charged particle in a magnetic field is perpendicular to both the velocity vector of the particle and the magnetic field vector.
The direction of the force experienced by a charged particle moving in a magnetic field is given by the right-hand rule. If you point your right thumb in the direction of the particle's velocity and your fingers in the direction of the magnetic field, then the direction in which your palm is facing gives the direction of the force.
If you reverse the direction of the charge (i.e. change it from positive to negative or vice versa), the direction of the force will reverse as well. However, if you reverse the direction of the magnetic field or the direction of the charge's motion, the direction of the force will also reverse.
This is because the force is proportional to the cross product of the velocity of the charged particle and the magnetic field. The cross product is a vector operation that gives a result that is perpendicular to both of the vectors being multiplied. As a result, reversing the direction of either vector will also reverse the direction of the resulting force vector.
To know more about magnetic field, visit:
brainly.com/question/23096032
#SPJ11
A Carnot refrigeration cycle is used to maintain a room at
23 °C by removing heat from groundwater at 15 °C.
Refrigerant R-134a enters the condenser as saturated
vapor at 40 °C and leaves as saturated liquid at the
same temperature. The evaporator pressure is 351 kPa.
a) If the room is to receive 2kW, what is power input to
the compressor?
b) Net power input to cycle?
a) The power input to the compressor in the Carnot refrigeration cycle, in order to supply 2 kW of cooling to the room, will depend on the efficiency of the cycle and the heat transfer involved.
b) The net power input to the cycle can be determined by considering the work done by the compressor and the work done on the system.
a) To calculate the power input to the compressor, we need to determine the heat transfer from the groundwater to the room. The Carnot refrigeration cycle is an idealized cycle, and its efficiency is given by the equation: Efficiency = 1 - (T_evaporator / T_condenser), where T_evaporator and T_condenser are the temperatures at the evaporator and condenser, respectively. Using this efficiency, we can calculate the heat transfer from the groundwater and convert it to power input.
b) The net power input to the cycle takes into account the work done by the compressor and the work done on the system. It can be calculated by subtracting the work done by the compressor from the heat transfer from the groundwater. The work done by the compressor can be determined using the power input calculated in part a), and the heat transfer from the groundwater can be obtained using the given temperatures and the specific heat properties of the refrigerant.
Overall, the Carnot refrigeration cycle involves several calculations to determine the power input to the compressor and the net power input to the cycle, considering the heat transfer and work done in the system.
To know more about the Carnot refrigeration cycle click here:
https://brainly.com/question/29234662
#SPJ11
A/C Transformer The input voltage to a transformer is 120 V RMS AC to the primary coil of 1000 turns. What are the number of turns in the secondary needed to produce an output voltage of 10 V RMS AC?
The number of turns in the secondary coil needed to produce an output voltage of 10 V RMS AC, given an input voltage of 120 V RMS AC to the primary coil with 1000 turns, is 83.33 turns (rounded to the nearest whole number).
To determine the number of turns in the secondary coil, we can use the turns ratio formula of a transformer:
[tex]Turns ratio = (Secondary turns)/(Primary turns) = (Secondary voltage)/(Primary voltage)[/tex]
Rearranging the formula, we can solve for the secondary turns:
[tex]Secondary turns = (Turns ratio) × (Primary turns)[/tex]
In this case, the primary voltage is 120 V RMS AC, and the secondary voltage is 10 V RMS AC. The turns ratio is the ratio of secondary voltage to primary voltage:
[tex]Turns ratio = (10 V)/(120 V) = 1/12[/tex]
Substituting the values into the formula, we can calculate the number of turns in the secondary coil:
[tex]Secondary turns = (1/12) * (1000 turns) = 83.33 turns[/tex]
Therefore, approximately 83.33 turns (rounded to the nearest whole number) are needed in the secondary coil to produce an output voltage of 10 V RMS AC.
Learn more about voltage here:
https://brainly.com/question/12804325
#SPJ11
An RL circuit is composed of a 12 V battery, a 6.0 Hinductor and a 0.050 Ohm resistor. The switch is closed at t = 0 The time constant is 1.2 minutes and after the switch has been closed a long time the voltage across the inductor is zero. The time constant is 2.0 minutes and after the switch has been closed a long time the voltage across the inductor is 12 V. The time constant is 1.2 minutes and after the switch has been closed a long time the voltage across the inductor is 12 V. The time constant is 2.0 minutes and after the switch has been closed a long time the current is
An RL circuit is composed of a 12 V battery, a 6.0 Hinductor and a 0.050 Ohm resistor. Therefore, After the switch has been closed a long time the current is 240A.
The RL circuit composed of a 12 V battery, a 6.0 H inductor, and a 0.050 Ohm resistor, with the switch closed at t=0.
The time constant, denoted as τ, is a measure of the rate at which the voltage or current in a capacitor or inductor changes during the charging/discharging phase.
The time constant is determined by the product of the resistance (R) and capacitance (C) or inductance (L).
The voltage across an inductor is given by the formula V = L(di/dt), where L is the inductance in henries, and di/dt is the rate of change of current with respect to time.
When the voltage across the inductor is zero, this means that the current is constant, and therefore there is no rate of change of current with respect to time, di/dt = 0.
When the voltage across the inductor is equal to the source voltage (12V), this means that the inductor is fully charged, and therefore the current in the circuit is constant.
In this case, the inductor acts like a wire, and the voltage across the resistor is equal to the source voltage, Vr = 12V.
The time constant, τ, of the circuit is given by τ = L/R. Therefore, the time constant of the circuit is 1.2 minutes when the voltage across the inductor is zero and when the voltage across the inductor is 12V.
The time constant of the circuit is 2.0 minutes when the current in the circuit is constant and equal to I = V/R = 12/0.050 = 240 A.
Therefore, After the switch has been closed a long time the current is 240A.
Learn more about capacitance (C) here:
https://brainly.com/question/31871398
#SPJ11
Compute the index of refraction of (a) air, (b) benzene, and (c) crown glass.
Answer:
The correct option is D Diamond.
From definition of refractive index,
μ=c/v
v=/cμ
v∝1/μ
So refractive index is inversely proportional to the refractive index of a medium. Hence the speed of light is slowest in the diamond.
The speed of light in a medium is inversely proportional to the refractive index of that medium.
Therefore, the medium with the highest refractive index will have the slowest speed of light.
Among the given options,
Diamond has the highest refractive index of 2.42.
Therefore, the speed of light would be slowest in diamond compared to air, water, and crown glass.
Learn more about index of refraction here
https://brainly.com/question/12469161
#SPJ11
Question:
The refractive index of air, water, diamond and crown glass is 1.0003, 1.33, 2.42 and 1.52 respectively. In which medium the speed of light would be the slowest?
Task 2
Activation Polarization is a mechanism that explains the
corrosion rate. Explain which part of the reaction determines the
total reaction rate.
Activation polarization is a mechanism that influences the corrosion rate, and it is the activation energy of the electrochemical reaction that determines the total reaction rate.
Activation polarization refers to the increase in the electrochemical reaction rate caused by the energy barrier, known as activation energy, that needs to be overcome for the reaction to proceed. The total reaction rate in corrosion is determined by the activation energy, which represents the minimum energy required for the reaction to occur.
In the context of corrosion, activation polarization occurs at the electrode-electrolyte interface. It is caused by various factors such as the nature of the corroding material, composition of the electrolyte, temperature, and presence of inhibitors. Activation polarization affects the rate of electrochemical reactions involved in the corrosion process.
When the activation energy is high, the reaction rate is low, leading to slower corrosion. On the other hand, when the activation energy is low, the reaction rate is high, resulting in faster corrosion. Therefore, the activation energy, which determines the activation polarization, plays a critical role in determining the total reaction rate of corrosion.
To know more about Activation polarization click here:
https://brainly.com/question/28963605
#SPJ11
(a) No lens can focus light down to a perfect point because there will always be some diffraction. Estimate the size of the minimum spot of light that can be expected at the focus of a lens. Discuss the relationship among the focal length, the lens diameter, and the spot size [8] (b) Calculate the gain coefficient of a hypothetical laser having the following parameters: inversion density = 10¹7 cm-³, wavelength = 700 nm, linewidth = 1 nm, spontaneous emission lifetime = 10-4 s. Assume n≈ 1 for the refractive index of the amplifier medium. [8] (c) How long should the resonator be to provide the total gain of 4?
(a) This equation tells us that the spot size decreases with decreasing wavelength, increasing focal length, and decreasing lens diameter. (b) Therefore, the gain coefficient, G = 1.67 x 10-23(1/0.5)(1017-0) = 3.34 x 10-6 m-1. (c) Thus, the resonator should be L = ln(4)/2g to provide the total gain of 4.
(a) No lens can focus light down to a perfect point because there will always be some diffraction.
The minimum spot of light that can be expected at the focus of a lens can be estimated using the Rayleigh criterion, which states that the spot size is given by Δx = 1.22λf/D, where λ is the wavelength of light, f is the focal length of the lens, and D is the diameter of the lens aperture.
This equation tells us that the spot size decreases with decreasing wavelength, increasing focal length, and decreasing lens diameter.
(b) The gain coefficient of a hypothetical laser can be calculated using the formula G = σ(η/ηst)(N2-N1), where σ is the stimulated emission cross-section, η is the pump efficiency, ηst is the saturation efficiency, N2 is the population density of the upper laser level, and N1 is the population density of the lower laser level.
For a 3-level laser, the population density of the lower laser level can be assumed to be zero, so N1=0. Inversion density, N2 = 1017 cm-3, spontaneous emission lifetime, τsp = 10-4 s, linewidth, Δλ = 1 nm, and the speed of light, c = 3 x 108 m/s.
Thus, the stimulated emission cross-section σ = (λ2/2πc)2(τsp/Δλ) = 1.67 x 10-23 m2.
The pump efficiency, η = 1, and the saturation efficiency, ηst = 0.5. Therefore, the gain coefficient, G = 1.67 x 10-23(1/0.5)(1017-0) = 3.34 x 10-6 m-1.
(c) The total gain, Gtot = exp(2gL), where L is the length of the laser cavity. Solving for L, we get L = ln(Gtot)/2g.
Thus, the resonator should be L = ln(4)/2g to provide the total gain of 4.
Learn more about resonator here:
https://brainly.com/question/32273580
#SPJ11
2 charged spheres 5m apart attract each other with a force of 15.0 x 10^6 N. What forces results from each of the following changes considered separately?
a) Both charges are doubled and the distance remains the same.
b) An uncharged, identical sphere is touched to one of the spheres, and then taken far away.
c) The separation is increased to 30 cm.
Answer:
Using Coulomb's Law, we know that the force of attraction between two charged objects is directly proportional to the product of their charges and inversely proportional to the square of the distance between them. In this case, we have two charged spheres 5m apart with an attraction of 15.0 x 10^6 N.
a) If both charges are doubled and the distance remains the same , we can calculate the new force of attraction using Coulomb's Law. Doubling the charges means we have a new charge of 2q on each sphere. Plugging in the new values, we get:
F = k * (2q)^2 / (5m)^2 = 4 * (k * q^2 / 5m^2) = 4 * (15.0 x 10^6 N) = 60.0 x 10^6 N.
Therefore, the new force of attraction is 60.0 x 10^6 N.
b) If an uncharged, identical sphere is touched to one of the spheres and then taken far away, the touched sphere will take on the same charge as the original charged sphere. This is because the charges on the two spheres will equalize and redistribute when they touch. The new force of attraction between the two charged spheres will be the same as the original force before the sphere was touched, since the charge on the touched sphere is the same as the original charged sphere. Once the touched sphere is taken far away, it will no longer contribute to the force of attraction between the two charged spheres, and the force will remain the same.
c) If the separation between the two charged spheres is increased to 30 cm, we can calculate the new force of attraction using Coulomb's Law. Plugging in the new distance value, we get:
F = k * q^2 / (0.3m)^2 = (k * q^2) / (0.09m^2) = (15.0 x 10^6 N) * (5^2) / (3^2) = 125.0 x 10^6 N.
Therefore, the new force of attraction between the two charged spheres is 125.0 x 10^6 N.
Explanation:
1. You have a grindstone (a disk) that is 94.0 kg, has a 0.400-m radius, and is turning at 85.0 rpm, and you press a steel axe against it with a radial force of 16.0 N.
(a) Assuming the kinetic coefficient of friction between steel and stone is 0.40, calculate the angular acceleration (in rad/s2) of the grindstone. (Indicate the direction with the sign of your answer.)
____rad/s2
(b)How many turns (in rev) will the stone make before coming to rest?
2.A gyroscope slows from an initial rate of 52.3 rad/s at a rate of 0.766 rad/s2.
(a)How long does it take (in s) to come to rest? ANSWER: (68.3s)
(b)How many revolutions does it make before stopping?
3.Calculate the moment of inertia (in kg·m2) of a skater given the following information.
(a)The 68.0 kg skater is approximated as a cylinder that has a 0.150 m radius.
0.765 kg·m2
(b)The skater with arms extended is approximately a cylinder that is 62.0 kg, has a 0.150 m radius, and has two 0.850 m long arms which are 3.00 kg each and extend straight out from the cylinder like rods rotated about their ends.
______kg·m2
Answer: 1a) The angular acceleration of the grindstone is -0.847 rad/s².1b) The grindstone makes 10.4 turns before coming to rest.
Answer:2a) The gyroscope takes 68.3 seconds to come to rest.2b) The gyroscope makes 352.6 revolutions before stopping.
Answer:3a) The moment of inertia of the skater is 0.765 kg·m².3b) The moment of inertia of the skater with arms extended is 2.475 kg·m².
1a) The angular acceleration of the grindstone is given by the formula τ = I α, where τ is the torque, I is the moment of inertia, and α is the angular acceleration. The torque τ is given by τ = Fr, where F is the force and r is the radius. Hence, we have:F = 16.0 N and r = 0.400 m.
The moment of inertia of a solid disk is given by I = (1/2) MR², where M is the mass and R is the radius. Hence, we have:M = 94.0 kg and R = 0.400 m.Substituting these values into the formula τ = I α, we get:τ = Fr = (16.0 N) (0.400 m) = 6.40 N.mI = (1/2) MR² = (1/2) (94.0 kg) (0.400 m)² = 7.552 kg.m²α = τ / I = (6.40 N.m) / (7.552 kg.m²) = 0.847 rad/s²The angular acceleration of the grindstone is 0.847 rad/s², in the direction opposite to its rotation.
1b) The final angular velocity of the grindstone is zero. Hence, we can use the formula ω² = ω₀² + 2αθ, where ω₀ is the initial angular velocity, θ is the angular displacement, and ω is the final angular velocity. Since the grindstone comes to a stop, we have ω = 0. Also, the angular displacement is given by θ = (2π)n, where n is the number of turns.
Substituting these values into the formula, we get:ω² = ω₀² + 2αθ0 = (85.0 rpm) (2π / 60 s/min) = 8.90 rad/sSubstituting these values into the formula, we get:0 = (8.90 rad/s)² + 2(-0.847 rad/s²)(2π)nSolving for n, we get:n = 10.4 revThe grindstone makes 10.4 turns before coming to rest.
Answer: 1a) The angular acceleration of the grindstone is -0.847 rad/s².1b) The grindstone makes 10.4 turns before coming to rest.
2a) The initial rate of the gyroscope is ω₀ = 52.3 rad/s, and the angular deceleration is α = -0.766 rad/s². We can use the formula ω = ω₀ + αt, where t is the time. Solving for t, we get:t = (ω - ω₀) / αSubstituting the values, we get:t = (0 - 52.3 rad/s) / (-0.766 rad/s²) = 68.3 sThe gyroscope takes 68.3 seconds to come to rest.
2b) The number of revolutions is given by the formula θ = ω₀t + (1/2) αt², where θ is the angular displacement. Since the final angular displacement is zero, we have:0 = ω₀t + (1/2) αt²Substituting the values, we get:0 = (52.3 rad/s) t + (1/2) (-0.766 rad/s²) t²Solving for t using the quadratic formula, we get:t = 68.3 s (same as part a)The number of revolutions is given by the formula θ = ω₀t + (1/2) αt². Substituting the values, we get:θ = (52.3 rad/s) (68.3 s) + (1/2) (-0.766 rad/s²) (68.3 s)² = 2217 radThe gyroscope makes 2217 / (2π) = 352.6 revolutions before stopping.Answer:2a) The gyroscope takes 68.3 seconds to come to rest.2b) The gyroscope makes 352.6 revolutions before stopping.
3a) The moment of inertia of a solid cylinder is given by the formula I = (1/2) MR², where M is the mass and R is the radius. Hence, we have:M = 68.0 kg and R = 0.150 m.Substituting these values into the formula, we get:I = (1/2) (68.0 kg) (0.150 m)² = 0.765 kg.m²The moment of inertia of the skater is 0.765 kg·m².
3b) The moment of inertia of a thin rod rotated about one end is given by the formula I = (1/3) ML², where M is the mass and L is the length. Hence, we have:M = 3.00 kg and L = 0.850 m.Substituting these values into the formula, we get:I = (1/3) (3.00 kg) (0.850 m)² = 0.683 kg.m²The moment of inertia of each arm is 0.683 kg·m².The moment of inertia of the skater with arms extended is the sum of the moment of inertia of the cylinder and the moment of inertia of the two arms, assuming they are rotated about the center of mass of the skater. The moment of inertia of a cylinder rotated about its center of mass is given by the formula I = (1/2) MR².
The center of mass of the skater with arms extended is at the center of the cylinder. Hence, we have:M = 62.0 kg and R = 0.150 m.Substituting these values into the formula, we get:Icyl = (1/2) (62.0 kg) (0.150 m)² = 1.109 kg.m²The moment of inertia of the cylinder is 1.109 kg·m².The moment of inertia of the skater with arms extended is given by the formula I = Icyl + 2Iarm = 1.109 kg·m² + 2(0.683 kg·m²) = 2.475 kg·m²The moment of inertia of the skater with arms extended is 2.475 kg·m².
Answer:3a) The moment of inertia of the skater is 0.765 kg·m².3b) The moment of inertia of the skater with arms extended is 2.475 kg·m².
Learn more about Velocity here,
https://brainly.com/question/80295
#SPJ11
The current supplied by a battery as a function of time is I(t) = (0.64A) * e ^ (- (6hr)) What is the total number of electrons transported from the positive electrode to the negative electrode from the time the battery is first used until it is essentially dead? (e = 1.6 * 10 ^ - 19 * C)
please answer quickly
To calculate the total number of electrons transported from the positive electrode to the negative electrode, we need to integrate the current function over the time interval during which the battery is in use.
The current function is given as I(t) = (0.64A) * e^(-6t), and we need to find the integral of this function.
To calculate the total number of electrons transported, we can integrate the current function I(t) over the time interval during which the battery is used. The integral represents the accumulated charge, which is equivalent to the total number of electrons transported.
The integral of the current function I(t) = (0.64A) * e^(-6t) with respect to time t will give us the total charge transported. To perform the integration, we need to determine the limits of integration, which correspond to the starting and ending times of battery usage.
Once we have the integral, we can divide it by the elementary charge e = 1.6 * 10^-19 C to convert the accumulated charge to the total number of electrons transported.
Learn more about integration here:
https://brainly.com/question/31744185
#SPJ11
During a very quick stop, a car decelerates at 6.8 m/s2. Assume the forward motion of the car corresponds to a positive direction for the rotation of the tires (and that they do not slip on the pavement).
Randomized Variablesat = 6.8 m/s2
r = 0.255 m
ω0 = 93 rad/s
Part (a) What is the angular acceleration of its tires in rad/s2, assuming they have a radius of 0.255 m and do not slip on the pavement?
Part (b) How many revolutions do the tires make before coming to rest, given their initial angular velocity is 93 rad/s ?
Part (c) How long does the car take to stop completely in seconds?
Part (d) What distance does the car travel in this time in meters?
Part (e) What was the car’s initial speed in m/s?
Part (a). the angular acceleration of the tires is 26.67 rad/s².Part (b)the tires make approximately 80.85 revolutions before coming to rest.Part (c)the car takes 3.49 seconds to stop completely.Part (d) the car travels 83.85 meters.Part (e)the initial speed of the car was 23.7 m/s.
Part (a)Angular acceleration, α can be calculated using the formula α = at/r.Substituting at = 6.8 m/s² and r = 0.255 m, we getα = 6.8/0.255α = 26.67 rad/s²Therefore, the angular acceleration of the tires is 26.67 rad/s².
Part (b)To calculate the number of revolutions the tires make before coming to rest, we can use the formulaω² - ω0² = 2αθwhere ω0 = 93 rad/s, α = 26.67 rad/s², and ω = 0 (since the tires come to rest).Substituting these values in the above equation and solving for θ, we getθ = ω² - ω0²/2αθ = (0 - (93)²)/(2(26.67))θ = 129.97 radThe number of revolutions the tires make can be calculated as follows:Number of revolutions, n = θ/2πrwhere r = 0.255 mSubstituting the values of θ and r, we getn = 129.97/(2π(0.255))n = 80.85 revTherefore, the tires make approximately 80.85 revolutions before coming to rest.
Part (c)Time taken by the car to stop, t can be calculated as follows:t = ω/αwhere ω = 93 rad/s and α = 26.67 rad/s²Substituting these values in the above equation, we gett = 3.49 sTherefore, the car takes 3.49 seconds to stop completely.
Part (d)Distance traveled by the car, s can be calculated using the formula,s = ut + 1/2 at²where u = initial velocity = final velocity, a = deceleration = -6.8 m/s² and t = 3.49 s.Substituting the values of u, a, and t in the above equation, we get,s = ut + 1/2 at²s = ut + 1/2 (-6.8)(3.49)²s = us = 83.85 mTherefore, the car travels 83.85 meters during this time.
Part (e)Initial speed of the car, u can be calculated using the formulau = ω0 ru = 93(0.255)u = 23.7 m/sTherefore, the initial speed of the car was 23.7 m/s.
Learn more about velocity here,
https://brainly.com/question/80295
#SPJ11
How many watts does a flashlight that has 6.4 x 10²C pass through it in 0.492 h use if its voltage is 3 V? __________ W
The power consumed by the flashlight is 10.92 W.
watt = volt x coulombs/sec
where:
watt = power
volt = voltage
coulombs/sec = charge/time
Put the given values in the formula, we get:
watt = 3 V × (6.4 × 10² C/0.492 h)
watt = 3 V × (6.4 × 10² C/1769.2 s)
watt = 10.92 W
Therefore, the power consumed by the flashlight is 10.92 W.
Learn more about power: https://brainly.com/question/11569624
#SPJ11
Electric Field a the Mid-Point of Two Charges The electric Field midway between two equal but opposite point charges is 1920 N/C, and the distance between the charges is 11.4 cm. What is the magnitude of the charge on each?
Given:
Electric field midway between two equal but opposite point charges is 1920 N/C. Distance between the charges is 11.4 cm.
Let q be the magnitude of the charge on each point charge.
Using Coulomb's law, the electric field E due to a point charge q at a distance r from it is given by;
E = kq/r
where k = 9 × 10^9 Nm²/C² is Coulomb's constant.
It follows that the electric field E at the midpoint between the two charges is given by;
E = (1/4πε₀) [2q/(11.4/2)²] = 1920 N/C
Where ε₀ is the permittivity of free space.
Evaluating for q;
q = E(11.4/2)²(4πε₀)/2
= 7.7 × 10^-6C (rounded off to 2 significant figures)
Therefore, the magnitude of the charge on each point charge is 7.7 × 10^-6 C.
What is an electric field?
An electric field is defined as a field of force surrounding an electrically charged particle that exerts a force on another charged particle that comes within its field of influence.
Learn more about permittivity of free space here
https://brainly.com/question/30403318
#SPJ11
(a) Sketch the relation between equivalent widths measured in a spectrum and the number of absorbing atoms. What is this relation called and what are the three main regimes and the physical explanation for these variations in the relation (2 points
The relation between equivalent widths measured in a spectrum and the number of absorbing atoms is known as the curve of growth. It exhibits three main regimes- linear regime, damping regime, and saturated regime.
The curve of growth describes the relationship between the equivalent widths measured in a spectrum and the number of absorbing atoms. It is a fundamental concept in spectroscopy. The curve of growth can be divided into three main regimes: the linear regime, the saturated regime, and the damping regime.
In the linear regime, the equivalent width of the spectral line is directly proportional to the number of absorbing atoms. As more absorbing atoms are added, the equivalent width increases linearly. In the saturated regime, adding more absorbing atoms does not result in a significant increase in the equivalent width. At this point, the spectral line becomes saturated, and the equivalent width plateaus.
In the damping regime, adding more absorbing atoms causes the equivalent width to decrease. This occurs because the line broadens due to collisions between the absorbing atoms. As the line broadens, the overall strength of the absorption decreases, resulting in a smaller equivalent width.
Understanding the curve of growth and its regimes is crucial for analyzing spectral data and determining the number of absorbing atoms in a system. By studying these variations, scientists can gain valuable insights into the physical properties of the absorbing medium.
Learn more about spectrum here:
https://brainly.com/question/31059971
#SPJ11
Calculate the resistivity of a manufactured "run" of annealed copper wire at 20°C, in ohms-circular mils/foot, if its conductivity is 96.5%. 3) A coil of annealed copper wire has 820 turns, the average length of which is 9 in. If the diameter of the wire is 32 mils, calculate the total resistance of the coil at 20°C. 4) The resistance of a given electric device is 46 ◊ at 25°C. If the temperature coefficient of resistance of the material is 0.00454 at 20°C, determine the temperature of the device when its resistance is 92 02.
The answer is 3) the total resistance of the coil at 20°C is 2.47 ohms and 4) the temperature of the device when its resistance is 92 ohms is 103.2°C.
3. Calculate the resistivity of a manufactured "run" of annealed copper wire at 20°C, in ohms-circular mils/foot, if its conductivity is 96.5%.
Given data: Conductivity = 96.5%
Resistivity = ?
Resistivity is the reciprocal of conductivity.ρ = 1/σ = 1/0.965 = 1.036 ohms-circular mils/foot
Therefore, the resistivity of a manufactured "run" of annealed copper wire at 20°C, in ohms-circular mils/foot is 1.036.2. A coil of annealed copper wire has 820 turns, the average length of which is 9 in. If the diameter of the wire is 32 mils, calculate the total resistance of the coil at 20°C.
Given data: Number of turns (N) = 820
Average length (L) = 9 in = 9 × 0.0833 = 0.75 ft
Diameter (d) = 32 mils
Resistance (R) = ?
Formula to calculate resistance of a coil R = ρ(N²L/d⁴)R = 10.37(N²L/d⁴) [Resistance in ohms]
Substituting the given values in the formula R = 10.37 × (820² × 0.75)/(32⁴) = 2.47 ohms
Therefore, the total resistance of the coil at 20°C is 2.47 ohms.
4. The resistance of a given electric device is 46 ohms at 25°C. If the temperature coefficient of resistance of the material is 0.00454 at 20°C, determine the temperature of the device when its resistance is 92 ohms.
Given data: Resistance at 25°C (R₁) = 46 ohms
Temperature coefficient of resistance (α) = 0.00454
The temperature at which α is given (T₂) = 20°C
The temperature at which resistance is to be calculated (T₁) = ?
Resistance at T₁ (R₂) = 92 ohms
Formula to calculate temperature T₁ = T₂ + (R₂ - R₁)/(R₁ × α)
Substituting the given values in the formula T₁ = 20 + (92 - 46)/(46 × 0.00454) = 103.2°C
Therefore, the temperature of the device when its resistance is 92 ohms is 103.2°C.
know more about ohms-circular
https://brainly.com/question/30702384
#SPJ11
Proton in a cube [40 points] A proton (charge +e=1.6×10 −19
C ) is located at the center of a cube of side length a. a) Find the total electric flux Φ tot
through the closed cube surface. Use ε 0
=8.85×10 −12
N⋅m 2
C 2
. Hint: The result is independent of the side length a of the cube. b) Find the electric flux Φ f
through one face (f) of the cube. Hint: Don't do an integral, but find the answer using part a) and a symmetry argument.
(a) The total electric flux through the closed cube surface is 1.81×10⁸N⋅m²C⁻¹.
(b) The electric flux through one face of the cube is 3.02×107N⋅m2C−1.
(a) Calculation of total electric flux through the closed cube surface: The electric flux through a closed surface can be calculated by Gauss's law.
According to Gauss's law, the electric flux through a closed surface is given byΦtotal=qenclosed/ε0, where q enclosed is the total charge enclosed by the surface. Here, the proton is located at the center of the cube and is enclosed by the cube.
Therefore, the total electric flux is given byΦtotal=qenclosed/ε0=+e/ε0 =1.6×10⁻¹⁹C/8.85×10⁻¹²N⋅m2C−2=1.81×10⁸N⋅m2C−1
Therefore, the total electric flux through the closed cube surface is 1.81×10⁸N⋅m²C⁻¹.
(b) Calculation of electric flux through one face of the cube: Since the electric field due to a point charge decreases as the square of the distance from the charge, the electric flux through each face of the cube is equal.
Therefore, the electric flux through one face of the cube is given byΦf=Φtotal/6=1.81×10⁸N⋅m2C−1/6=3.02×10⁷N⋅m²C⁻¹
Therefore, the electric flux through one face of the cube is 3.02×10⁷N⋅m²C⁻¹.
To learn about electric flux here:
https://brainly.com/question/14372859
#SPJ11
What is the net force acting on a 56 gram chicken egg that falls from a tree with a velocity of 5 m/s if it come to rest after 0.17 seconds?
Net force is the overall force that acts on an object. It is determined by adding up all of the individual forces acting on an object.
The net force acting on a 56-gram chicken egg that falls from a tree with a velocity of 5 m/s if it comes to rest after 0.17 seconds can be found as follows:
The mass of the chicken egg is 56 grams, and it can be converted to kilograms by dividing it by 1000.
56 g ÷ 1000 = 0.056 kg
The acceleration of the egg can be determined as
a = (v_f - v_i) / t where: v_f is the final velocity, v_i is the initial velocity, t is the time it takes to come to rest,
v_f = 0 (since the egg comes to rest)
v_i = 5 m/s
t = 0.17 s
a = (0 - 5 m/s) / 0.17 s⇒ a = -29.4 m/s²
To determine the net force acting on the egg, the formula for force can be used:
F = m × a
F = 0.056 kg × -29.4 m/s²
F = -1.6464 N
This gives the force that acted on the egg. The negative sign indicates that the force acted in the opposite direction to the velocity of the egg. However, the question asks for the net force, which means we have to take the magnitude of this value:
|F| = 1.6464 N
Thus, the net force acting on the egg is 1.6464 N.
Learn more about force: https://brainly.com/question/25239010
#SPJ11
Two hollow metal spheres are concentric with each other. The inner sphere has a radius of 0.130 m and a potential of 88.5 V. The radius of the outer sphere is 0.154 m and its potential is 74.3 V. If the region between the spheres is filled with Teflon, find the electric energy contained in this space. Number Units
Two hollow metal spheres are concentric with each other. The inner sphere has a radius of 0.130 m and a potential of 88.5 V. the electric energy contained in the space between the spheres is zero.
To find the electric energy contained in the space between the concentric spheres, we need to calculate the electric potential energy. The electric potential energy (U) can be calculated using the formula:
U = q * V,
where q is the charge and V is the electric potential.
Since the region between the spheres is filled with Teflon, which is an insulator, the charge on the inner sphere induces an equal and opposite charge on the outer sphere. Therefore, the total charge between the spheres is zero.
The electric potential difference (ΔV) between the spheres can be calculated by subtracting the potential of the inner sphere from the potential of the outer sphere:
ΔV = V_outer - V_inner
= 74.3 V - 88.5 V
= -14.2 V
Since the charge is zero, the electric potential energy (U) in the space between the spheres is also zero. This is because the electric potential energy depends on the product of charge and potential, and since the charge is zero, the energy is zero.
Therefore, the electric energy contained in the space between the spheres is zero.
Learn more about electric potential energy here:
https://brainly.com/question/28444459
#SPJ11
Block 1, mass 1.00kg, slides east along a horizontal frictionless surface at 2.50m/s. It collides elastically with block 2, mass 5.00kg, which is also sliding east at 0.75m/s. Determine the final velocity of both blocks.
The final velocities of both blocks are 0.95 m/s and 0.31 m/s respectively.
Mass of Block 1, m1 = 1.00 kg
Initial velocity of block 1, u1 = 2.50 m/s
Mass of Block 2, m2 = 5.00 kg
Initial velocity of block 2, u2 = 0.75 m/s
Both blocks move in the same direction and collide elastically. Final velocities of both blocks to be determined.
Using conservation of momentum:
Initial momentum = Final momentum
m1u1 + m2u2 = m1v1 + m2v2
m1u1 + m2u2 = (m1 + m2) V....(1)
Using conservation of energy, for an elastic collision:
Total kinetic energy before collision = Total kinetic energy after collision
1/2 m1 u1² + 1/2 m2 u2² = 1/2 m1 v1² + 1/2 m2 v2²....(2)
Solving equations (1) and (2) to obtain the final velocities:
v1 = (m1 u1 + m2 u2) / (m1 + m2)v2 = (2 m1 u1 + (m2 - m1) u2) / (m1 + m2)
Substituting the given values,
m1 = 1.00 kg,
u1 = 2.50 m/s,
m2 = 5.00 kg,
u2 = 0.75 m/s
Final velocity of Block 1,
v1= (1.00 kg x 2.50 m/s + 5.00 kg x 0.75 m/s) / (1.00 kg + 5.00 kg)= 0.95 m/s (East)
Final velocity of Block 2,
v2 = (2 x 1.00 kg x 2.50 m/s + (5.00 kg - 1.00 kg) x 0.75 m/s) / (1.00 kg + 5.00 kg)= 0.31 m/s (East)
Thus, the final velocity of block 1 is 0.95 m/s (East) and the final velocity of block 2 is 0.31 m/s (East).
Hence, the final velocities of both blocks are 0.95 m/s and 0.31 m/s respectively.
Learn more about velocity:
https://brainly.com/question/25905661
#SPJ11
Light of 580 nm passing through a single slit, shows a diffraction pattern on a screen 4.50 m behind the all
as the one in the graph below.
a) What is the width of the central maximum?
b) Can we consider small angle approximation? Consider first minimum for order of magnitude (show
calculations that support your answer)
c) What is the width of the slit?
d) What is the distance from the central maximum to the 5th minimum?
e) If the length between the screen and the slit was increased, would the central maximum get wider,
narrower or it will not change?
f) If the width of the slit was increased, would the central maximum get wider, narrower or it will not
change?
The graph:
Question 2: The camera of a satellite has a diameter of 40cm. The satellite is orbiting 250 km from the surface of earth. What is the minimum distance 2 objects could be on the surface of earth to be result by this camera? Consider 500 cm light.
a) the width of the central maximum is 2.36 mm.b)Small angle approximation is valid.c)The width of the slit is 41.7 µm.
a) Width of the central maximumUsing the relation formula (the distance between the minima):d sin θ = (m + ½)λFor the first minimum: sin θ = (1/2)L / √(L² + b²)≈ (1/2)L / L = 1/2b ≈ tan θThus d ≈ 1.22λ / b= 1.22 × 580 nm / 0.30 mm≈ 2.36 × 10⁻³ m = 2.36 mmThe width of the central maximum is 2.36 mm.
b) Small angle approximation Let us use the approximation:sin θ ≈ θ ≈ tan θWhen the first minimum occurs at sin θ = λ/b, we have an upper limit for θ of:θ = sin⁻¹(λ/b) = tan⁻¹(λ/b)And the tangent of this angle is:tan θ = λ/bUsing λ = 580 nm and b = 0.3 mm, we get:tan θ ≈ 0.002 ≈ θThe small angle approximation is valid.
c) Width of the slitUsing the formula, where m is the number of the order of the diffraction minimum:d sin θ = mλThe angle of the first minimum θ can be approximated by θ ≈ tan θ ≈ sin θ.Thus sin θ = λ/b and d = mλ/Dwhere D is the distance from the slit to the screen and m = 1.Let's find D by using the ratio of the triangle's sides:D / b = L / √(L² + b²).
Then D = bL / √(L² + b²)We have:b = 0.3 mmL = 4.50 mD = bL / √(L² + b²)≈ 0.0139 mλ = 580 nmUsing the formula, we get:d = mλ / D≈ 0.000580 / 0.0139 m≈ 4.17 × 10⁻⁵ m = 41.7 µmThe width of the slit is 41.7 µm.
Learn more about angle here,
https://brainly.com/question/1309590
#SPJ11
Dara and Cameron are studying projectile motion in their physics lab class. They set up a Pasco projectile launcher on the edge of their lab table, so that the ball will be launched at an initial height of H=33.5 inches, initial velocity of v
0
=3.4 m/s and an initial angle of θ 0
=37 ∘
(see diagram). They can then record the landing location by placing a piece of carbon paper on the floor some distance away from the launcher. When the ball lands, it will make a mark on the carbon paper. a) Find horizontal component of initial velocity (two significant figures please). σ 4
b) Find vertical component of initial velocity (two significant figures please). β c) Find the maximum height of the motion (two significant figures please). d) Find the landing location on carbon paper (three significant figures this time).
a) The horizontal component of initial velocity is 2.722 m/s.b) The vertical component of initial velocity is 2.023 m/s.c) The maximum height of the motion is 0.982 m.d) The landing location on carbon paper is 1.746 m.
Projectile motion is the path of an object through the air when it's acted upon by gravity. It's described as a two-dimensional motion since the object is moving in two directions. It has horizontal and vertical components, and each component is independent of the other. It can be calculated with the help of horizontal and vertical components of initial velocity, time, and acceleration due to gravity.
Projectile motion can be studied with the help of a Pasco projectile launcher, and it involves finding the horizontal component of initial velocity, vertical component of initial velocity, maximum height of the motion, and the landing location on carbon paper.a) To find the horizontal component of initial velocity, we can use the following formula:v₀ = v₀ cos(θ₀)Where v₀ is the initial velocity, and θ₀ is the initial angle. We're given:v₀ = 3.4 m/sθ₀ = 37°.
Therefore:v₀ = 3.4 cos(37°)v₀ ≈ 2.722 m/sThe horizontal component of initial velocity is 2.722 m/s. (to two significant figures)b) To find the vertical component of initial velocity, we can use the following formula:v₀ = v₀ sin(θ₀)Where v₀ is the initial velocity, and θ₀ is the initial angle. We're given:v₀ = 3.4 m/sθ₀ = 37°Therefore:v₀ = 3.4 sin(37°)v₀ ≈ 2.023 m/sThe vertical component of initial velocity is 2.023 m/s. (to two significant figures)c) To find the maximum height of the motion, we can use the following formula:y = H + v₀² sin²(θ₀) / 2gWhere H is the initial height, v₀ is the initial velocity, θ₀ is the initial angle, and g is the acceleration due to gravity.
We're given:H = 33.5 in = 0.8509 mv₀ = 3.4 m/sθ₀ = 37°g = 9.81 m/s²Therefore:y = 0.8509 + (3.4² sin²(37°)) / (2 x 9.81)y ≈ 0.982 mThe maximum height of the motion is 0.982 m. (to two significant figures)d) .
To find the landing location on carbon paper, we can use the following formula:x = v₀ cos(θ₀) tWhere v₀ is the initial velocity, θ₀ is the initial angle, and t is the time taken. The time taken can be calculated with the help of the following formula:y = H + v₀ sin(θ₀) t - 1/2 g t²Where H is the initial height, v₀ is the initial velocity, θ₀ is the initial angle, and g is the acceleration due to gravity. We're given:H = 33.5 in = 0.8509 mv₀ = 3.4 m/sθ₀ = 37°g = 9.81 m/s²We can convert the initial height into meters:0.8509 m = 2.79 ftv₀y = v₀ sin(θ₀) = 2.023 m/st = v₀y / g + sqrt(2gh) / gWe can plug in the values: t = 2.023 / 9.81 + sqrt(2 x 9.81 x 0.8509) / 9.81t ≈ 0.421 sThe time taken is 0.421 seconds. (to three significant figures).
Now we can find the landing location:x = v₀ cos(θ₀) tWhere v₀ is the initial velocity, θ₀ is the initial angle, and t is the time taken. We're given:v₀ = 3.4 m/sθ₀ = 37°t = 0.421 sTherefore:x = 3.4 cos(37°) x 0.421x ≈ 1.746 mThe landing location on carbon paper is 1.746 m. (to three significant figures)
Answer:a) The horizontal component of initial velocity is 2.722 m/s. (to two significant figures)b) The vertical component of initial velocity is 2.023 m/s. (to two significant figures)c) The maximum height of the motion is 0.982 m. (to two significant figures)d) The landing location on carbon paper is 1.746 m. (to three significant figures)
Learn more about Pasco projectile here,
https://brainly.com/question/8104921
#SPJ11
Consider a spherical container of inner radius r1-8 cm, outer radius r2=10 cm, and thermal conductivity k-45 W/m *C, The inner and outer surfaces of the container are maintained at constant temperatures of T₁-200°C and T-80°C, respectively, as a result of some chemical reactions occurring inside. Obtain a general relation for the temperature distribution inside the shell under steady conditions, and determine the rate of heat loss from the container
The rate of heat loss from the container is given by q = k * T₂ * A / [tex]r_2[/tex]². To obtain the general relation for the temperature distribution inside the shell of the spherical container under steady conditions, we can use the radial heat conduction equation and apply it to both the inner and outer regions of the shell.
Radial heat conduction equation:
For steady-state conditions, the radial heat conduction equation in spherical coordinates is given by:
1/r² * d/dr (r² * dT/dr) = 0,
where r is the radial distance from the center of the sphere, and T is the temperature as a function of r.
Inner region[tex](r_1 < r < r_2):[/tex]
For the inner region, the boundary conditions are T([tex]r_1[/tex]) = T₁ and T([tex]r_2[/tex]) = T₂. We can solve the radial heat conduction equation for this region by integrating it twice with respect to r:
dT/dr = A/r²,
∫ dT = A ∫ 1/r² dr,
T = -A/r + B,
where A and B are integration constants.
Using the boundary condition T([tex]r_1[/tex]) = T₁, we can solve for B:
T₁ = -A/[tex]r_1[/tex] + B,
B = T₁ + A/[tex]r_1[/tex].
So, for the inner region, the temperature distribution is given by:
T(r) = -A/r + T₁ + A/[tex]r_1[/tex].
Outer region (r > r2):
For the outer region, the boundary condition is T([tex]r_2[/tex]) = T₂. Similarly, we integrate the radial heat conduction equation twice with respect to r:
dT/dr = C/r²,
∫ dT = C ∫ 1/r² dr,
T = -C/r + D,
where C and D are integration constants.
Using the boundary condition T([tex]r_2[/tex]) = T₂, we can solve for D:
T₂ = -C/[tex]r_2[/tex] + D,
D = T₂ + C/[tex]r_2[/tex].
So, for the outer region, the temperature distribution is given by:
T(r) = -C/r + T₂ + C/[tex]r_2[/tex].
Combining both regions:
The temperature distribution inside the shell can be expressed as a piecewise function, taking into account the inner and outer regions:
T(r) = -A/r + T₁ + A/[tex]r_1[/tex], for [tex]r_1 < r < r_2[/tex],
T(r) = -C/r + T₂ + C/[tex]r_2[/tex], for[tex]r > r_2[/tex].
To determine the integration constants A and C, we need to apply the boundary conditions at the interface between the two regions (r = [tex]r_2[/tex]). The temperature and heat flux must be continuous at this boundary.
At r = [tex]r_2[/tex], we have T([tex]r_2[/tex]) = T₂:
-T₂/[tex]r_2[/tex] + T₂ + C/[tex]r_2[/tex] = 0,
C = T₂ * [tex]r_2[/tex].
The rate of heat loss from the container can be calculated using Fourier's Law of heat conduction:
q = -k * A * dT/dr,
where q is the heat flux, k is the thermal conductivity, and dT/dr is the temperature gradient. The heat flux at the outer surface (r = [tex]r_2[/tex]) can be determined as:
q = -k * A * (-C/[tex]r_2[/tex]²) = k * T₂ * A / [tex]r_2[/tex]².
Therefore, the rate of heat loss from the container is given by:
q = k * T₂ * A / [tex]r_2[/tex]².
Learn more about conduction here:
https://brainly.com/question/31260735
#SPJ11
A loop of wire with a diameter of 20 cm is located in a uniform magnetic field. The loop is perpendicular to the field. The field has a strength of 2.0 T. If the loop is removed completely from the field in 1.75 ms, what is the average induced emf? If the loop is connected to a 150 kohm resistor what is the current in the resistor?
Answer: The current in the resistor is 0.00024 A.
The average induced emf can be determined by Faraday's law of electromagnetic induction which states that the emf induced in a loop of wire is proportional to the rate of change of the magnetic flux passing through the loop.
Mathematically: ε = -N(ΔΦ/Δt)
where,ε is the induced emf, N is the number of turns in the loop, ΔΦ is the change in the magnetic flux, Δt is the time interval.
The magnetic flux is given as,Φ = BA
where, B is the magnetic field strength, A is the area of the loop.
Since the loop has been completely removed from the field, the change in magnetic flux (ΔΦ) is given by,ΔΦ = BA final - BA initial. Where,
BA initial = πr²
B = π(0.1m)²(2.0 T)
= 0.0628 Wb.
BA final = 0 Wb (As the loop has been removed completely from the field).
Therefore,ΔΦ = BA final - BA initial
= 0 - 0.0628
= -0.0628 Wb.
Since the time interval is given as Δt = 1.75 ms
= 1.75 × 10⁻³ s, the induced emf can be calculated as,
ε = -N(ΔΦ/Δt)
= -N × (-0.0628/1.75 × 10⁻³)
= 35.94 N.
The average induced emf is 35.94 V (approx).
Now, if the loop is connected to a 150 kΩ resistor, the current in the resistor can be determined using Ohm's law, which states that the current passing through a conductor between two points is directly proportional to the voltage across the two points and inversely proportional to the resistance between them. Mathematically, it can be represented as,
I = V/R Where, I is the current flowing through the resistor V is the voltage across the resistor R is the resistance of the resistor. From the above discussion, we know that the induced emf across the loop of wire is 35.94 V, and the resistor is 150 kΩ = 150 × 10³ Ω
Therefore, I = V/R
= 35.94/150 × 10³
= 0.00024 A.
The current in the resistor is 0.00024 A.
Learn more about Ohm's law : https://brainly.com/question/14296509
#SPJ11
Both of the following statements apply to Part (a) answers and Part (b) answers: (a) Two protons exert a repulsive force on one another when separated by 6.4 fm. What is the magnitude of the force on one of the protons? (b) What is the magnitude of the electric field of a proton at 6.4 fm? (Enter your answer in calculation notation to 3-sigfigs with appropriate units. Ex: 3.00X10" = 3,00E+8). Answers are to 3SigFigs in calculator notation. Use proper units.
(a) Therefore, the magnitude of the force on one of the protons is 3.62 × 10⁻¹¹ N. (b) Therefore, the magnitude of the electric field of a proton at 6.4 fm is 8.99 × 10⁶ N/C.
(a) Two protons exert a repulsive force on one another when separated by 6.4 fm.
The magnitude of the force on one of the protons can be calculated using Coulomb's law.
Coulomb's law states that the force between two charges is proportional to the product of the charges and inversely proportional to the square of the distance between them.
Mathematically, F = (k * q1 * q2) / r²Where F is the force, k is Coulomb's constant (8.99 × 10⁹ N · m²/C²), q1 and q2 are the charges, and r is the distance between the charges.
The magnitude of the force on one of the protons can be calculated as follows:F = (8.99 × 10⁹ N · m²/C²) * ((+1.6 × 10⁻¹⁹ C)² / (6.4 × 10⁻¹⁵ m)²)≈ 3.62 × 10⁻¹¹ N
Therefore, the magnitude of the force on one of the protons is 3.62 × 10⁻¹¹ N.
(b) The magnitude of the electric field of a proton at 6.4 fm can be calculated using Coulomb's law.
Coulomb's law states that the electric field created by a point charge is proportional to the charge and inversely proportional to the square of the distance from the charge.
Mathematically,E = k * (q / r²)Where E is the electric field, k is Coulomb's constant (8.99 × 10⁹ N · m²/C²), q is the charge, and r is the distance from the charge.
The magnitude of the electric field of a proton at 6.4 fm can be calculated as follows:E = (8.99 × 10⁹ N · m²/C²) * (+1.6 × 10⁻¹⁹ C / (6.4 × 10⁻¹⁵ m)²)≈ 8.99 × 10⁶ N/C
Therefore, the magnitude of the electric field of a proton at 6.4 fm is 8.99 × 10⁶ N/C.
Learn more about repulsive force here:
https://brainly.com/question/24013868
#SPJ11
A mass is suspended from a string and moves with a constant upward velocity. Which statement is true concerning the tension in the string?
a. The tension is equal to the weight of the mass.
b. The tension is less than the weight of the mass
c. The tension is equal to zero.
d. The tension is greater than the weight of the mass
e. The tension is equal to the mass
The correct statement concerning the tension in the string when a mass is suspended and moves with a constant upward velocity is:
b. The tension is less than the weight of the mass.
When a mass is suspended and moves with a constant upward velocity, the tension in the string is not equal to the weight of the mass. If the tension in the string were equal to the weight of the mass (statement a), the net force acting on the mass would be zero, resulting in no upward movement. Since the mass is moving upward with a constant velocity, the tension in the string must be less than the weight of the mass.
The tension in the string is responsible for providing an upward force that counteracts the downward force of gravity acting on the mass. The tension must be slightly less than the weight of the mass to achieve a constant upward velocity. If the tension were equal to or greater than the weight of the mass, the net force would be upward, causing the mass to accelerate upward.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
A cave rescue team lifts an injured spelunker directly upward and out of a sinkhole by means of a motor-driven cable. The lift is performed in three stages, each requiring a vertical distance of 14.0 m: (a) the initially stationary spelunker is accelerated to a speed of 4.70 m/s; (b) he is then lifted at the constant speed of 4.70 m/s; (c) finally he is decelerated to zero speed. How much work is done on the 75.0 kg rescue by the force lifting him during each stage? (a) Number ___________ Units _____________
(b) Number ___________ Units _____________
(c) Number ___________ Units _____________
Work done in accelerating the rescue: 7841.25 Joules. Work done when lifting at a constant speed: 10296.3 Joules. Work done in decelerating the rescue: -7841.25 Joules.
(a) Mass of the rescue, m = 75.0 kg
Initial velocity, u = 0 m/s
Final velocity, v = 4.70 m/s
Vertical distance covered in each stage, d = 14.0 m (for stage a)
The work done in accelerating the rescue can be calculated using the work-energy principle:
Work = Change in kinetic energy
The change in kinetic energy is equal to the final kinetic energy deducted by the initial kinetic energy:
Change in kinetic energy = (1/2) * m * v^2 - (1/2) * m * u^2
Since the initial velocity is zero, the initial kinetic energy term becomes zero:
Change in kinetic energy = (1/2) * m * v^2
Change in kinetic energy = (1/2) * 75.0 kg * (4.70 m/s)^2
Calculating the work:
Work = Change in kinetic energy * Distance
Work = (1/2) * 75.0 kg * (4.70 m/s)^2 * 14.0 m
Calculating the result:
Work = 7841.25 Joules
So, the work done on the 75.0 kg rescue during stage (a) is 7841.25 Joules.
(b )Lifted at a constant speed of 4.70 m/s:
In this stage, the spelunker is lifted at a constant speed, which means there is no change in kinetic energy. The force required to lift the spelunker at a constant speed is equal to the gravitational force acting on them.
Mass of the rescue, m = 75.0 kg
Acceleration due to gravity is 9.81 m/s^2.
Vertical distance covered in each stage, d = 14.0 m (for stage b)
The work done in this stage can be calculated as:
Work = Force * Distance
The force required to lift the rescue at a constant speed is equal to their weight:
Force = Weight = m * g
Force = 75.0 kg * 9.81 m/s^2
Calculating the work:
Work = Force * Distance = (75.0 kg * 9.81 m/s^2) * 14.0 m
Calculating the result:
Work = 10296.3 Joules
Therefore, the work done on the 75.0 kg rescue during stage (b) is 10296.3 Joules.
(c) Decelerated to zero speed:
In this stage, the spelunker is decelerated to zero speed, which means their final velocity is zero.
Mass of the rescue, m = 75.0 kg
Initial velocity, u = 4.70 m/s
Final velocity, v = 0 m/s
Vertical distance covered in each stage, d = 14.0 m (for stage c)
The work done in decelerating the rescue can be calculated using the work-energy principle:
Work = Change in kinetic energy
The change in kinetic energy is equal to the final kinetic energy minus the initial kinetic energy:
Change in kinetic energy = (1/2) * m * v^2 - (1/2) * m * u^2
Since the final velocity is zero, the final kinetic energy term becomes zero:
Change in kinetic energy = - (1/2) * m * u^2
Substituting the given values:
Change in kinetic energy = - (1/2) * 75.0 kg * (4.70 m/s)^2
Calculating the work:
Work = Change in kinetic energy * Distance
Work = - (1/2) * 75.0 kg * (4.70 m/s)^2 * 14.0 m
Calculating the result:
Work = - 7841.25 Joules
Therefore, the work done on the 75.0 kg rescue during stage (c) is -7841.25 Joules.
Learn more about Work done at: https://brainly.com/question/28356414
#SPJ11
The note Middle A on a piano has a frequency of 440 Hz. a. If someone is playing Middle A on the piano and you want to hear Middle B instead (493.883 Hz), with what velocity should you move? b. How about if you want Middle C (256 Hz)? c. What is the wavelength of Middle C?
a. To hear Middle B (493.883 Hz) instead of Middle A (440 Hz) on the piano, you should move with a velocity that is 12% faster than your current velocity.
b. To hear Middle C (256 Hz) instead of Middle A (440 Hz) on the piano, you should move with a velocity that is approximately 49% slower than your current velocity.
c. For Middle C (256 Hz), the wavelength would be approximately 1.34 meters.
The frequency of a sound wave is directly proportional to the velocity of the source. To hear a higher frequency (Middle B) than the original frequency (Middle A), you need to increase your velocity. Since Middle B has a frequency that is 12% higher than Middle A, you would need to increase your velocity by approximately 12%.
Conversely, to hear a lower frequency (Middle C) than the original frequency (Middle A), you need to decrease your velocity. Middle C has a frequency that is approximately 42% lower than Middle A, so you would need to slow down your velocity by approximately 49% to hear Middle C.
The wavelength of a sound wave can be calculated using the formula λ = v/f, where λ represents the wavelength, v represents the velocity of sound, and f represents the frequency. For Middle C with a frequency of 256 Hz and assuming a velocity of sound in air of approximately 343 meters per second, the wavelength is calculated to be approximately 1.34 meters. This means that the distance between two consecutive peaks or troughs of the sound wave is 1.34 meters.
Learn more about wavelength here:
https://brainly.com/question/31322456
#SPJ11