A circular coin of radius R and mass M is placed so that it touches a step of length R as shown in figure. The minimum value of the horizontal force F required to pull the coin over the step Is?​

Answer:

A lunar eclipse occurs when the Moon enters the Earth’s shadow. A solar eclipse occurs when the Moon’s shadow falls on the Earth. They do not happen every month because the Earth’s orbit around the sun is not in the same plane as the Moon’s orbit around the Earth.

Explanation:

(a) When you apply a force of 40 N, the magnitude of the horizontal component of the force that the floor exerts on the block is 51 N.

(b) When you apply a force of 59 N, the magnitude of the horizontal component of the force that the floor exerts on the block is 51 N.

The horizontal component of the force that the floor exerts on the block is determined by applying Newton's second law of motion;

[tex]F = ma[/tex]

[tex]\Sigma F = 0\\\\F - F_f = 0\\\\F = F_f[/tex]

[tex]F_f = F\\\\F_f = 51 \ N[/tex]

where;

Since the surface (floor) is constant, the frictional force (horizontal component of the force that the floor exerts on the block ) will be the same on the cases.

Learn more about frictional force here: https://brainly.com/question/24386803

Based on the definition of limiting frictional force;

Force is any push or pull effect which tends to cause a change in the motion or shape of an object.

Based on Newton's third law, every force produces an equal and opposite reaction.

Therefore, the force that the floor exerts on the block is oppositely direction to the force exerted by the horizontal force acting on the block.

Since a horizontal force of 51 N applied to the block is required to keep the block moving across the floor at a constant speed, this is the limiting frictional force.

a) when a force of 40 N is applied to the block, the magnitude of the horizontal component of the force that the floor exerts on the block is equal to 40 N

b) when a force of 59 N is applied to the block, the magnitude of the horizontal component of the force that the floor exerts on the block is equal to 51 N, the limiting frictional force.

Learn more about limiting frictional force at: https://brainly.com/question/23092926

Answer:

chemical energy

Explanation:

hope this helps

Answer:

The acceleration of an item is proportional to the net force exerted on it and inversely proportional to its mass. When the force pushing on an item rises, so does the object's acceleration. The acceleration of an item decreases as the mass of the thing increases.

If the force on an object remains constant, increasing mass will decrease acceleration. In other words, force and acceleration are directly proportional, while mass and acceleration are inversely proportional. ( How Newton's Laws of Motion Work" 29 July 2008.)

If the mass of an object is held constant, increasing force will increase acceleration. If the force on an object remains constant, increasing mass will decrease acceleration.

This net force is the resultant force of all forces acting on the body at any given instant. The larger the magnitude of this net force, the larger the acceleration of the body. One of the definitions of mass is the resistance of a body to motion in general and acceleration in particular due to the application of force.

Explanation:

Answer:

C, D, and E

Explanation:

Answer:it’s C, D, E

Explanation:

Answer:

*Good luck!

Answer:

A. put water in a container under the pot water will disappear from the container .

Answer:

im pretty sure its D

Explanation:

Answer:

D

Explanation:

Heat will flow from object B to object A

Answer:

0.0519480519 A

Explanation:

First find equivalent resistance:

R series = R1 + R2 + R3 ...

[tex]R_{eq} = 160+100+82+120=462ohms[/tex]

Now calculate current:

V = IR

[tex]I = \frac{V}{R}[/tex]

[tex]I= \frac{24}{462} = 0.0519480519 A[/tex]

Workdone:-

[tex]\\ \tt\longrightarrow Force\times Displacement [/tex]

[tex]\\ \tt\longrightarrow 500(100)[/tex]

[tex]\\ \tt\longrightarrow 50000J[/tex]

final speed will be 25.98 m/s Explanation Force applied by the engine on the car is  We have to find final speed of the car after travelling 300 m , so displacement of car is given as  so wor done by the engines on the car

Answer:

[tex]F=ma \\ 900 = 1200a \\ a = \frac{3}{4} m. {s}^{ - 2} \\ {v}^{2} = {u}^{2} +2 as \\ {v}^{2} = {(15)}^{2} + 2( \frac{3}{4} )(300) \\ = 675 \\ v = \sqrt{675} \: m. {s}^{ - 1} [/tex]

The distance travelled by the hockey puck, given that 60 J of work was done by an applied force of 5 N is 12 meters

We know already that work is the product of force and distance moved in the direction of the force:

Work done (Wd) = force (F) × distance (d)

Using the above formula, we can determine the distance travelled by the hockey puck. Details below:

Work done (Wd) = force (F) × distance (d)

60 = 5 × distance travelled

Divide both sides by 5

Distance travelled = 60 / 5

Distance travelled = 12 meters

Thus, from the above calculation, we can conclude that the distance travelled is 12 meters

Learn more about distance travelled:

https://brainly.com/question/18265275

#SPJ1

Answer:

a variable (often denoted by x) whose variation does not depend on that of another.

Explanation:

l will help and if you get it correctly I will say you are welcome

Answer:

48.5 m/s².

Explanation:

We can use the following kinematic equation:

[tex]\displaystyle v_f = v_i + at[/tex]

Substitute in the appropriate values and solve for acceleration a:

[tex]\displaystyle \begin{aligned} (1250\text{ m/s}) & = (280\text{ m/s}) + a(20\text{ s}) \\ \\ a & = 48.5\text{ m/s$^2$} \end{aligned}[/tex]

Therefore, the acceleration of the fighter jet was 48.5 m/s².

The horizontal force needed to keep the same box sliding on the same horizontal floor at a given constant speed is 45 N.

The horizontal force needed to keep the same box sliding on the same horizontal floor at a given constant speed is calculated as follows;

[tex]F= \frac{mv}{t} \\\\mv = Ft\\\\m = \frac{Ft}{v} \\\\\frac{F_1}{v_1} = \frac{F_2}{v_2}[/tex]

where;

[tex]F_2 = \frac{F_1v_2}{v_1} \\\\F_2 = \frac{15 \times 1.5}{0.5} \\\\F_2 = 45 \ N[/tex]

Thus, the horizontal force needed to keep the same box sliding on the same horizontal floor at a given constant speed is 45 N.

Learn more about horizontal force here: https://brainly.com/question/12979825

Maths :

The length between 2 points.

Physics =

Distance = speed × time

Distance is defined as the space between two points in space.

Distance is defined as the space between two points in space.

The unit of distance is metres or kilometres.

Distance can be measured directly usind instruments such as metre rule and tape rule.

The formula for calculating distance is given below:

Distnce = velocity × time.

Therefore, distance is defined as the space between two points in space.

Learn more about about distance at: https://brainly.com/question/4931057

(a) The time taken for the ball to reach the height of the fence is 4.1 s.

(b) The position of the ball from the batter at the time is 111.33 m.

(c) Henry will have a home run.

The time taken for the ball to reach the height of the fence is calculated as follows;

[tex]h = v_0_y t - \frac{1}{2} gt^2\\\\(3 - 1.2) = (34 \times sin37)t - \frac{1}{2} (9.8)t^2\\\\1.8 = 20.46t- 4.9t^2\\\\4.9t^2 - 20.46t+ 1.8 = 0\\\\a = 4.9, \ b = -20.46, \ c = 1.8\\\\t = \frac{-b\pm \sqrt{b^2 - 4ac} }{2a} \\\\t = 4.1 \ s[/tex]

The position of the ball at the time is calculated as follows;

[tex]X = v_x t\\\\X = (34 \times cos37) \times 4.1\\\\X = 111.33 \ m[/tex]

Since, 111.33 m is greater than 106 m, Henry will have a home run.

Learn more about about time of motion here: https://brainly.com/question/2364404

Answer:

the water will float over mercury and the steel ball will be in it's respected place

Answer:

the answer is b because an object in motion stays in motion

The water likely spilled because of inertia of motion such that an object in motion tends to stay in motion. So, option B is correct.

Inertia is defined as the property of matter by which it tends to continue its state of rest or uniform motion.

Here,

When you are travelling in a car, holding a cup of water in one hand and the driver of the car is forced to stop suddenly so that the water in the cup gets spilled out.

When the car was moving, the water in the cup was actually at the same speed relative to the car and cup. When the car is tend to stop suddenly, this causes a sudden change in acceleration of the car and thus the cup. As a result, the water in the cup spills out. This is due to the property of inertia that the water got spilled out.

According to the law of inertia, a body will preserve its state of rest or uniform motion unless an external force acts on it.

Here, the spilling out of water is the application of inertia of motion. That means the the water inside the cup which was moving forward and when the change in acceleration occurred, it got spilled in front of you thus tending to continue its state of motion.

Hence,

The water likely spilled because of inertia of motion such that an object in motion tends to stay in motion.

To learn more about inertia, click:

https://brainly.com/question/769460

#SPJ7

Answer:

its inertia.

Inertia is the tendency of an object to continue in the state of rest or of uniform motion

Answer:

1/2mv²=0

1/2(4kg)(v²)=0

2=-v²

square root -2=v

v=1.414

Block A of mass 1 kg and block B has a mass of 3 kg, then the blocks collide and stick together so the kinetic energy of block A is one-third of the kinetic energy of the block.

Kinetic energy is a type of power that an item or particle possesses as a result of motion. When an item undergoes work—the transfer of energy—by having subject to a net force, it accelerates and consequently obtains kinetic energy. An object in motion or particle's kinetic energy, which depends on both mass and speed, is one of its features. Any combination of motions, including translation, rotation about an axis, and vibration, may be used as the type of motion.

A body's translational kinetic energy is equal to 1/2mv², or one-half of the sum of its mass, m, and the square of its velocity, v.

To know more about Kinetic energy:

https://brainly.com/question/12669551

#SPJ5

Answer: 148348.6239 kg•m/s

Explanation: Firstly, we need to convert the 14700 N into kilograms, and to do so, use the formula net force is equal to mass times acceleration and rearrange the formula to find mass like shown below...

F = ma

F/a = m

14700/9.81 = 1498.470948 kg, this is your mass

Now that we convert it into kilograms, plug all the numbers into the variable of the momentum formula.

Momentum formula is P = mass x velocity

Like this:

P = 1498.470948 x 99

p = 148348.6239 kg•m/s.

I believe that is your answer, hope that helps you even a bit out.

Thanks.  

The charge on the capacitor 2 (C₂) is 48μF.

In the circuit diagram, C₁ and C₂ are in series connection, while C₃ is parallel to C₁ and C₂.

[tex]Q_1 = Q_2 = Q\\\\V = \frac{Q}{C_1} + \frac{Q}{C_2} \\\\V = Q(\frac{1}{C_1} + \frac{1}{C_2} )\\\\Q = V (\frac{C_1C_2}{C_1 + C_2} )\\\\Q = 24 \times (\frac{6 \times 10^{-6} \times 3 \times 10^{-6}}{6\times 10^{-6} \ + \ 3 \times 10^{-6}} )\\\\Q = \frac{4.32 \times 10^{-10}}{9\times 10^{-6}} \\\\Q = 48 \ \mu C[/tex]

Thus, the charge on the capacitor 2 (C₂) is 48μF.

Learn more about charge on capacitor here: brainly.com/question/13578522

Answer:

0.072, 0.062, 0

Explanation:

Flux = magnetic field B * area A * cos(angle between B and normal of A)

= 1.25 * 0.24^2 * cos(angle) = 0.072 * cos(angle)

a) angle = 0°, flux = 0.072 Wb

b) angle = 30°, flux = 0.072*cos(30) = 0.062 Wb.

c) angle = 90°, flux = 0

you produce about 20 W

Explanation:

Determine the time in which the work will be done. Here, we can take t = 60 s . Power is equal to work divided by time. In this example, P = 9000 J / 60 s = 150 W(example)

Answer:

Explanation:

To determine the power (or rate of work) produced, we can use the formula:

Power = Work / Time

Where:

Work = 140 J (joules)

Time = 7 seconds

So, we can plug in the values into the formula:

Power = 140 J / 7 s = 20 W (watts)

So, you produced 20 watts of power in 7 seconds.

It's important to note that work and power are different physical quantities. Work represents the amount of energy transferred, while power represents the rate at which that energy is transferred.