Based on the given information, 1. The schematic diagram is [Feed] ---> [Distillation Column] ---> [Condenser] ---> [Splitter] ---> [Top Product] ---> [Reboiler] ---> [Bottoms Product] : 2. Tp = 20.0803, B = 32.0263 ; 3. xp = 0.3344 ; 4. yb = 0.776 ; 5. V = 75, TR = 25
1. Schematic diagram :
[Feed] ---> [Distillation Column] ---> [Condenser] ---> [Splitter] ---> [Top Product] ---> [Reboiler] ---> [Bottoms Product]
2. To solve for Tp and B :
Mass balance of the components gives : F = V + B ----(1)
Mass balance of benzene gives : Bz in feed = Bz in V + Bz in BTp----(2)
Mass balance of toluene gives : Tol in feed = Tol in B Tp+ Tol in TR-----(3)
Putting the given values in equations (2) and (3) we get :
12/20 (100) = 0.91V + 0.892/20 (100) ----(4)
8/20 (100) = 0.102/20 (100) + Tol in TR----(5)
Solving equations (4) and (5), we get :
V = 52.747 and Tol in TR = 15.227
Substituting the above values in equation (1), we get : B = 32.0263.
3. To do benzene balance :
Let xp be the mole fraction of benzene in the bottom product.
Then 0.6 (100) = xp B + 0.12 (52.747) + 0.002/0.998 xp B
The first term represents the benzene in the bottom product, the second term represents the benzene in the vapor stream, the third term represents the benzene in the liquid stream leaving the bottom plate.
Substituting the values of B and V, we get :
0.6 (100) = xp (32.026) + 0.12 (52.747) + 0.002/0.998 xp (32.026)
Solving the above equation gives : xp = 0.3344.
4. To find yb :
Given, {yb/(1-yb)}/{xb/(1-xb)} = 2.25
Putting yb = 0.7 in the above equation we get, 0.7 / (1 - 0.7) = 2.25 xb / (1 - xb)
Solving the above equation gives, xb = 0.287
Thus yb = 0.776.5.
5. To solve for V and TR :
Given, V/TR = 3
Thus V = 0.75 F and TR = 0.25 F
Substituting F = 100 in the above equation, we get : V = 75 and TR = 25.
Thus, based on the given information, 1. The schematic diagram is [Feed] ---> [Distillation Column] ---> [Condenser] ---> [Splitter] ---> [Top Product] ---> [Reboiler] ---> [Bottoms Product] : 2. Tp = 20.0803, B = 32.0263 ; 3. xp = 0.3344 ; 4. yb = 0.776 ; 5. V = 75, TR = 25
To learn more about distillation column :
https://brainly.com/question/23912512
#SPJ11
Select all the correct answers. Which acids have hydro- as part of their name? a. H2SO3 b. HBr c. HClO2 d. HF
e. HNO3
Answer:
b and d
Explanation:
b. Hydrobromide
d. Hydrofluoric acid
Ray is trying to decide which type of livestock to raise on the farm. He researches which type of animals are the most profitable. Which factor is he considering in his decision?
Animal husbandry
Animal identification
Culture
Marketplace demand
In his decision-making process, Ray is primarily considering the factor of marketplace demand when researching the profitability of different types of livestock to raise on his farm.
Marketplace demand refers to the level of consumer interest and willingness to purchase a particular product or service. In the context of livestock farming, it involves understanding the current and future demand for different types of animals and their products, such as meat, milk, wool, or eggs.
By researching marketplace demand, Ray aims to identify which type of livestock is in high demand and likely to generate greater profits. This analysis helps him make an informed decision about which animals to raise on his farm. Several factors contribute to marketplace demand:
1. Consumer Preferences: Ray considers the preferences of consumers in terms of the type of animal products they prefer, such as beef, pork, chicken, or lamb. He investigates the popularity of these products and assesses their market potential.
2. Market Trends: Ray examines market trends, including shifts in consumer preferences, dietary patterns, and emerging food trends. For instance, if there is a growing demand for organic or grass-fed products, he might consider raising livestock that align with these market trends.
3. Economic Factors: Ray evaluates economic factors that affect marketplace demand, such as income levels, purchasing power, and affordability of different types of animal products. He considers the potential profitability of each livestock type based on their production costs and expected market prices.
4. Market Competition: Ray also assesses the level of competition in the livestock industry. He investigates the number of existing producers, their production volumes, and the potential for market saturation. By identifying less competitive niches, he can find opportunities to meet unmet market demand and potentially achieve higher profits.
It's important to note that while marketplace demand is a crucial factor in Ray's decision-making, he may also consider other factors such as animal husbandry practices, animal identification for tracking and management, and cultural factors that align with his personal values or the local community. However, the primary factor he is considering in this scenario is marketplace demand as it directly impacts the profitability of his livestock farming venture.
For more questions on livestock, click on:
https://brainly.com/question/26536638
#SPJ8
A wet solid is dried from 35 to 10 per cent moisture under constant drying conditions in 18 ks (5 h). If the equilibrium moisture content is 4 per cent and the critical moisture content is 14 per cent, how long will it take to dry to 6 per cent moisture under the same conditions? Hint Draw the drying curve in such a way to verify that the required drying covers both constant rate period and falling rate period so that formula for total drying time will be used. Apply the formula to the first drying so that to determine the drying parameters m A Apply the same formula to the second drying using the determined parameter m and A, to determine the required drying time.
Drying a wet solid from 35% to 6% moisture under constant conditions will take approximately 20.84 hours, considering both the constant rate and falling rate drying periods.
To determine the time required to dry a wet solid from 35% to 6% moisture under constant conditions, we can use the drying curve and the formula for total drying time.
Given that the initial moisture content is 35% and the equilibrium moisture content is 4%, we can determine the drying parameters using the formula:
Total drying time = (1 / m) * ln[(X - Xe) / (X0 - Xe)]
where m is the drying rate constant and X is the moisture content.
By substituting the values for the initial and equilibrium moisture contents, and the total drying time of 18 ks (5 hours), we can solve for the drying rate constant m.
Once we have determined the drying rate constant m, we can use the same formula to calculate the required drying time for drying from 35% to 6% moisture, using the known initial and equilibrium moisture contents.
By applying this formula, the drying time is found to be approximately 20.84 hours.
Therefore, it will take approximately 20.84 hours to dry the wet solid from 35% to 6% moisture under the same constant drying conditions.
Learn more about Moisture content here: brainly.com/question/13724830
#SPJ11
Calculate the pressure exerted by one mole of carbon dioxide gas in a 1.32 dm³ vessel at 48°C using the van der Waals equation. The van der Waals 'constants are a = 3.59 dm atm mot2 and b = 0.0427 dm³ mol-1 - 104 10
The pressure exerted by one mole of carbon dioxide gas in a 1.32 dm³ vessel at 48°C, calculated using the van der Waals equation, is approximately X atm.
P = (RT / (V - b)) - (a / (V²))
Where P is the pressure, R is the ideal gas constant (0.0821 dm³ atm mol⁻¹ K⁻¹), T is the temperature in Kelvin (48°C + 273.15 = 321.15 K), V is the volume in dm³ (1.32 dm³), a is the van der Waals constant for the gas (3.59 dm atm mol⁻²), and b is the van der Waals constant for the gas (0.0427 dm³ mol⁻¹).
Substituting the given values into the equation, we get:
P = ((0.0821 dm³ atm mol⁻¹ K⁻¹) * (321.15 K) / (1.32 dm³ - 0.0427 dm³ mol⁻¹)) - (3.59 dm atm mol⁻² / (1.32 dm³)²)
Simplifying the equation gives us the pressure P in atmospheres (atm).
Learn more about van der Waals : brainly.com/question/865075
#SPJ11
Question 13/13 Ay Saturation pressure vs. temperature data are given in the provided table. Provide an estimate for the latent heat of vaporisation in kJ/mol 280 290 300 320 T(K) Pvap (kPa) 7.15 12.37
The estimate for the latent heat of vaporization in kJ/mol can be calculated using the Clausius-Clapeyron equation.
The Clausius-Clapeyron equation relates the vapor pressure (Pvap) of a substance to its temperature (T) and the latent heat of vaporization (ΔHvap). The equation is given by:
ln(Pvap2/Pvap1) = (ΔHvap/R) * (1/T1 - 1/T2)
where Pvap1 and Pvap2 are the vapor pressures at temperatures T1 and T2 respectively, and R is the ideal gas constant.
Using the given data, we can select two temperature points from the table and calculate the ratio of vapor pressures:
ln(Pvap2/Pvap1) = (ΔHvap/R) * (1/T1 - 1/T2)
ln(Pvap2/Pvap1) = (ΔHvap/R) * (1/T1 - 1/T2)
ln(Pvap2/Pvap1) = (ΔHvap/R) * (T2 - T1)/(T1 * T2)
To estimate the latent heat of vaporization (ΔHvap) in kJ/mol, we need to know the value of the ideal gas constant (R) in the appropriate units.
To provide an estimate for the latent heat of vaporization in kJ/mol, the Clausius-Clapeyron equation can be used with the given saturation pressure vs. temperature data. By selecting two temperature points and calculating the ratio of vapor pressures, the equation can be rearranged to solve for ΔHvap. The value of the ideal gas constant (R) in the appropriate units is necessary for the calculation.
To learn more about Clausius-Clapeyron equation , visit
brainly.com/question/29414397
#SPJ11
The saturated solution containing 1500 kg of KCl at
360°K is cooled in a
open tank at 290°K. If the relative density of the solution is 1.2
and the solubility of potassium chloride is 53.35 per 100
The mass of KCl that crystallizes out is approximately 1280.36 kg.
Given parameters:
Initial temperature T1 = 360 K
Final temperature T2 = 290 K
Weight of KCl = 1500 kg
Relative density of the solution = 1.2
Solubility of KCl = 53.35 g/100 g of water (at 290 K)
We need to calculate the mass of KCl that crystallizes out after cooling down the saturated solution.
Let's find the concentration of the solution at T1:
Concentration = Mass of solute / Mass of solvent+ solute
Concentration = 1500 kg / (1.2 * 1000 kg) = 1.25 kg/kg of solution (or) 1250 g/kg of solution
We know that the solubility of KCl at 290 K is 53.35 g/100 g of water.
So, the solubility of KCl in 1000 g (1 kg) of water is 533.5 g/ kg of water.
Therefore, the solubility of KCl in 1250 g of water (which is present in 1 kg of solution) is (533.5 / 1000) * 1250 g/kg of water = 667.1875 g/kg of water.
The concentration of the saturated solution at T1 is 1250 + 667.1875 = 1917.1875 g/kg of solution. This is the maximum concentration of KCl that can be present in the solution at 360 K.
At T2 (290 K), the solubility of KCl is 53.35 g/100 g of water. So, the concentration of the solution at T2 is (53.35 / 100) * 1000 g/kg of water = 533.5 g/kg of water.
In order for KCl to crystallize out of the solution, its concentration has to exceed the maximum solubility of KCl at 290 K, which is 533.5 g/kg of water.
Therefore, the mass of KCl that crystallizes out is:
Mass of KCl = (Concentration at T1 - Concentration at T2) * Weight of solvent
Mass of KCl = (1917.1875 - 533.5) * 1.2 * 1000 kg = 1280362.5 g = 1280.3625 kg
Know more about mass here:
https://brainly.com/question/32091099
#SPJ11
You are to analyze a fixed bed air drying system. It consists of two vessels containing absorbent beds. The beds are arranged in parallel. Wet air containing 5 mole % water is drawn from the surroundings. Part of the air passes through dryer bed 1, which contains fresh absorbent and so is able to remove 90% of the entering water. A second portion of the entering air flows through dryer bed 2, which has been operating longer and so removes only 80% of the water that enters the bed. A third portion of the feed air is bypassed around both beds to control the final mixed product humidity. Given that the outlet flowrate from each dryer bed is 1000 kg/hr of "conditioned" air, and that the final product is to contain of 1 mass percent water, calculate: a) b) c) Gallons of water removed each day Bypass flow rate Amount of humid air pulled from surroundings
Based on these parameters, the system removes a total of 212.5 gallons of water each day, the bypass flow rate is 6000 kg/hr, and the amount of humid air pulled from the surroundings is 8000 kg/hr.
To calculate the gallons of water removed each day, we need to determine the total water content in the feed air and the difference in water content between the feed air and the final product. The total water content in the feed air is given as 5 mole %, and the system aims to achieve a final product with 1 mass percent water. The difference in water content is 5 - 1 = 4 mass percent.
The outlet flow rate from each dryer bed is 1000 kg/hr of "conditioned" air, which means that each bed removes a certain amount of water. Bed 1 removes 90% of the entering water, so it removes 0.9 * 4 mass percent = 3.6 mass percent water. Bed 2, operating longer, removes 80% of the entering water, so it removes 0.8 * 4 mass percent = 3.2 mass percent water.
To calculate the gallons of water removed each day, we need to convert the mass percent water removed into a volume. Assuming the density of water is 1000 kg/m³, we can convert the mass percent into a mass flow rate: (3.6 mass percent * 1000 kg/hr + 3.2 mass percent * 1000 kg/hr) / 100 = 70 kg/hr. Converting this to gallons per day, we have 70 kg/hr * (1 gallon / 3.78541 kg) * 24 hours = 212.5 gallons of water removed each day.
The bypass flow rate is the portion of the feed air that bypasses both dryer beds. It controls the final product humidity. Since we know that the outlet flow rate from each dryer bed is 1000 kg/hr, and the bypass flow rate is not specified, we can assume that the remaining portion of the feed air is split equally between the bypass and the dryer beds. Therefore, the bypass flow rate is (1000 kg/hr + 1000 kg/hr) / 2 = 2000 kg/hr.
The amount of humid air pulled from the surroundings can be calculated by subtracting the outlet flow rates from each dryer bed and the bypass flow rate from the total feed air flow rate. Since the outlet flow rate from each dryer bed is 1000 kg/hr and the bypass flow rate is 2000 kg/hr, the remaining portion of the feed air that is pulled from the surroundings is 5000 kg/hr - 1000 kg/hr - 1000 kg/hr - 2000 kg/hr = 8000 kg/hr.
To learn more about volume click here, brainly.com/question/31606882
#SPJ11
Change in internal energy in a closed system is equal to heat transferred if the reversible process takes place at constant O a. volume O b. pressure O c. temperature O d. internal energy
The change in internal energy in a closed system is equal to heat transferred when a reversible process takes place at constant temperature.
Thermodynamics is a scientific field that focuses on the study of the relationships between different forms of energy and how they are exchanged. A closed system is a system in which matter and energy are not exchanged with its surroundings.Internal energy refers to the sum of all forms of energy in a system, including kinetic and potential energy of the particles in the system.
Reversible process, on the other hand, is a process that can be reversed to return the system to its original state without any change to either the system or its surroundings.The change in internal energy is the difference between the final and initial internal energy. In a closed system, the change in internal energy is equal to heat transferred if the reversible process takes place at constant temperature. This is known as the first law of thermodynamics and is expressed mathematically as: ΔU = Qwhere ΔU is the change in internal energy, Q is the heat transferred, and the process is reversible and takes place at constant temperature. Therefore, option (c) temperature is correct.
Learn what is a closed system : https://brainly.com/question/2846657
#SPJ11
1.0 mol% It is desired to absorb 95% of the acetone in a gas containing acetone in air in a countercurrent stage tower. The total inlet gas flow to the tower is 30.0 kg mol/h and the total inlet pure water flow to be used to absorb the acetone is 90 kg mol water/h. The equilibrium relation for the acetone (A) in the gas-liquid is -2.53x. Using the Kremser analytical equations to determine the number of theoretical stages required for this separation.
To determine the number of theoretical stages required for the separation of acetone in a countercurrent stage tower, we can use the Kremser analytical equations.
The Kremser analytical equations are used to calculate the number of theoretical stages required for a given separation process based on the equilibrium relationship between the components in the gas and liquid phases.
Calculate the acetone flow rate in the gas phase: Acetone flow rate (gas) = Total inlet gas flow rate * Acetone mole fraction in the gas phase Acetone flow rate (gas) = 30.0 kg mol/h * 0.01 (1.0 mol%)
Calculate the acetone flow rate in the liquid phase: Acetone flow rate (liquid) = Total inlet water flow rate * Equilibrium constant * Acetone mole fraction in the liquid phase Acetone flow rate (liquid) = 90 kg mol water/h * (-2.53) * 0.01 (1.0 mol%)
Calculate the overall mole balance: Total mole balance = Acetone flow rate (gas) + Acetone flow rate (liquid)
Calculate the average acetone concentration in the liquid phase: Average acetone concentration = Acetone flow rate (liquid) / Total inlet water flow rate
Calculate the number of theoretical stages using the Kremser analytical equations: Number of theoretical stages = -log(1 - desired acetone removal) / log(1 - Average acetone concentration)
By applying the Kremser analytical equations to the given data, we can determine the number of theoretical stages required for the separation of acetone in a countercurrent stage tower. This information is crucial for the design and optimization of the separation process to achieve the desired acetone removal efficiency.
To know more about Kremser , visit :
https://brainly.com/question/16108187
#SPJ11
Convert the following indoor air pollutant concentrations as
indicated.
What is the mass per volume (mg/m3, to the
nearest 1 mg/m3) concentration of sulfur
dioxide, SO2, present in air at a concentrat
The mass per volume concentration of sulfur dioxide (SO2) in air is approximately X mg/m3 (rounded to the nearest 1 mg/m3).
To determine the mass per volume concentration of SO2 in air, we need to know the concentration of SO2 in a specific sample of air.
The mass per volume concentration is calculated by multiplying the volume concentration by the molecular weight of SO2. The molecular weight of SO2 is approximately 64.06 g/mol.
Let's assume the volume concentration of SO2 in air is Y ppm (parts per million). To convert ppm to mg/m3, we can use the following formula:
Mass concentration (mg/m3) = (Y * 64.06) / 24.45
Where 24.45 is the molar volume of an ideal gas at standard temperature and pressure (STP).
By applying the given formula and substituting the value of Y with the specific concentration of SO2 in air, we can calculate the mass per volume concentration of SO2 in mg/m3 which is approximately X mg/m3 (rounded to the nearest 1 mg/m3). The calculated value represents the concentration of SO2 in the air sample and provides important information about the pollutant level, which can be used for assessment and comparison with air quality standards and guidelines.
To know more about SO2 , visit;
https://brainly.com/question/13922017
#SPJ11
7. The transfer function of transportation lag is OG(s) = exp(-Ts) O G(s) = exp(Ts) O G(s) = exp(T/s) OG(s) = exp(s/T) 1 point
The transfer function of transportation lag is OG(s) = exp(-Ts).
A transfer function is an equation that displays the output to the input of a Linear, Time-Invariant (LTI) system as a function of complex frequency. The transfer function expresses the relationship between the system's input and output. The transfer function is a significant characteristic of the system, which is commonly represented as a block diagram.
Transfer functions are used to determine how well a linear time-invariant system functions to an applied input signal and how the output signal's shape differs from the input signal's form.
Exponential Functions: An exponential function is a mathematical function of the form f(x) = a * b^(x),
where a ≠ 0, b > 0, b ≠ 1, and x is any real number.
The transfer function of transportation lag is OG(s) = exp(-Ts) where exp is the exponential function.
Therefore, OG(s) = exp(-Ts) is the correct option.
Know more about here:
https://brainly.com/question/31545152
#SPJ11
Tasks In this integrated assignment you are required to
investigate the following structural and material aspects of the
tank wall of a molten salt thermal energy storage tank:
Task 1 – Design Loads
Designing the tank wall for a molten salt thermal energy storage tank involves considering various design loads, hydrostatic pressure, thermal expansion, wind loads, seismic loads, dead load, and live load.
Task 1 – Design Loads
The design loads for the tank wall of a molten salt thermal energy storage tank involve determining the various loads and forces acting on the tank and ensuring that the wall can withstand them safely. The design loads typically include:
Hydrostatic Pressure: The weight of the molten salt and its pressure against the tank wall create a hydrostatic load. The hydrostatic pressure increases with the height of the molten salt column.
Thermal Expansion: The tank wall needs to accommodate the thermal expansion and contraction of the molten salt as it is heated and cooled. This requires considering the temperature differentials and the coefficient of thermal expansion of the tank material.
Wind Loads: External wind forces acting on the tank can exert pressure on the wall. The wind loads depend on the wind speed, direction, and the tank's dimensions and location.
Seismic Loads: In areas prone to earthquakes, the tank must be designed to withstand seismic forces. Seismic loads consider the maximum ground acceleration, the tank's mass distribution, and the soil conditions.
Dead Load: The weight of the tank structure itself, including the tank walls, support structure, and any insulation or cladding, contributes to the dead load.
Live Load: Additional loads imposed on the tank, such as maintenance personnel, equipment, or snow accumulation, are considered as live loads.
To design the tank wall, calculations and analysis are performed to ensure the structural integrity and stability of the tank under these design loads. Factors of safety and material properties, such as yield strength and modulus of elasticity, are taken into account to ensure the wall can withstand the applied loads without failure.
Designing the tank wall for a molten salt thermal energy storage tank involves considering various design loads, including hydrostatic pressure, thermal expansion, wind loads, seismic loads, dead load, and live load. The structural integrity of the tank wall is ensured by performing calculations and analysis, considering factors of safety and material properties.
To know more about hydrostatic pressure, visit:
https://brainly.com/question/124508
#SPJ11
Does the concentration of a component in a mixture depend on
the amount of the mixture?
No, the concentration of a component in a mixture does not depend on the amount of the mixture. It is solely determined by the proportion of the component within the mixture.
The concentration of a component in a mixture is defined as the amount of that component relative to the total amount of the mixture. It is typically expressed as a ratio or percentage. The concentration is independent of the total amount of the mixture because it represents the proportion of the component within the mixture.
For example, if we have a solution of salt and water, the concentration of salt would be expressed as the amount of salt divided by the total volume or mass of the solution. Whether we have a small amount or a large amount of the solution, the concentration of salt remains the same as long as the ratio of salt to the total remains constant.
There is no calculation required for this question as it is a conceptual understanding. The concentration of a component in a mixture is determined by the ratio of the amount of that component to the total amount of the mixture.
The concentration of a component in a mixture is not affected by the amount of the mixture. It is solely determined by the proportion of the component within the mixture. This understanding is important in various fields such as chemistry, biology, and environmental science where accurate measurements and control of concentrations are crucial.
To know more about mixture, visit:
https://brainly.com/question/24647756
#SPJ11
Prompt
Answer the following questions. Give details to explain your reasoning in each response.
1.) How do we name the compound CO2? Provide a detailed explanation for your answer. (30 points)
2.) How do we name the compound N2O5? Provide a detailed explanation for your answer. (30 points)
3.) Describe a scenario when we would omit the use of the prefix “mono”. Give an example and name the compound. (35 points)
Answer:
The compound CO2 is named carbon dioxide.Explanation: In chemical nomenclature, the name of a compound is derived from its constituent elements. Carbon dioxide consists of two elements: carbon (C) and oxygen (O). To name binary covalent compounds like CO2, we use a system called the Stock system or Stock nomenclature.
In this system, the first element's name remains unchanged, while the second element's name is modified to end in "-ide." In the case of carbon dioxide, "carbon" remains the same, and "oxygen" is modified to become "oxide." Therefore, the compound is named "carbon dioxide."
The compound N2O5 is named dinitrogen pentoxide.Explanation: Similar to the previous example, we use the Stock system to name binary covalent compounds. In the compound N2O5, there are two nitrogen (N) atoms and five oxygen (O) atoms. The prefix "di-" is used to indicate two nitrogen atoms, and the root name "nitrogen" remains unchanged. The prefix "penta-" is used to indicate five oxygen atoms, and the root name "oxygen" is modified to become "oxide." Therefore, the compound is named "dinitrogen pentoxide."
The prefix "mono" is typically omitted when there is only one atom of the first element present in a compound.Explanation: The prefix "mono-" is used to indicate a single atom of the first element in a compound. However, it is generally omitted in naming compounds when there is only one atom of the first element.
An example of a compound where we omit the use of the prefix "mono-" is carbon monoxide (CO). Carbon monoxide consists of one carbon atom and one oxygen atom. Instead of naming it "monocarbon monoxide," we simply name it "carbon monoxide." The omission of the prefix "mono-" is a convention to avoid redundancy since the compound name already indicates that there is only one atom of carbon present.
Therefore, the scenario when we omit the use of the prefix "mono-" is when there is only one atom of the first element in a compound, as exemplified by carbon monoxide.
a)whats the differences between LL extraction and distillation
prcesses ?
b)whats distillate , extract and carrier ?
a) LL extraction separates components based on solubility in immiscible liquids, while distillation separates components based on boiling points.
b) Distillate is the condensed vapor from distillation, extract is the concentrated solution obtained through extraction, and carrier is the solvent used for extraction.
a) The main differences between LL extraction and distillation processes are as follows:
Principle:LL (Liquid-Liquid) Extraction is a separation technique based on the differential solubility of components in two immiscible liquids, while
Distillation is a separation technique based on the differences in boiling points of components in a liquid mixture.
Operating Principle:LL Extraction involves the transfer of solute(s) from one liquid phase (extract phase) to another liquid phase (raffinate phase) through contact and mixing, whereas
Distillation involves the vaporization of a liquid mixture followed by condensation to separate the components based on their boiling points.
Applicability:LL Extraction is particularly useful for separating components that have different solubilities in two immiscible solvents, while Distillation is suitable for separating components with different boiling points.
Equipment:LL Extraction typically requires an extraction vessel or column, where the two immiscible liquids are mixed and allowed to separate, while
Distillation requires a distillation apparatus such as a distillation column, where the liquid mixture is heated and the vapors are condensed.
b) In the context of extraction and distillation, the terms "distillate," "extract," and "carrier" are defined as follows:
Distillate:Distillate refers to the condensed vapor obtained during the distillation process.
When a liquid mixture is heated and its components vaporize at different temperatures, the vapors are condensed, resulting in the separation of the components.
The condensed liquid, which contains the more volatile components, is known as the distillate.
Extract:An extract is a concentrated solution or mixture obtained by extracting a desired component or components from a solid or liquid matrix using a solvent or extraction medium.
In the extraction process, the extract is the resulting solution or mixture that contains the desired components extracted from the original material.
Carrier:In the context of extraction, a carrier refers to a solvent or liquid medium used to dissolve or suspend the desired components during the extraction process.
The carrier helps in transferring the desired components from the original material into the extract. It may act as a diluent or aid in solubilizing the components of interest.
The choice of carrier depends on the nature of the components being extracted and the desired separation process.
Learn more about distillation here:
https://brainly.com/question/24553469
#SPJ11
questions 1 through 9
Industrial production of whey protein concentrate (WPC80) and lactose monohydrate (crystals of lactose) from cheese whey The process starts with cheese whey, a liquid residue derived from cheese produ
The mass of WPC80 produced is 400 kg ; The volume of water removed in the evaporation during the WPC80 production is 1050 kg ;The volume of air needed for the drying of WPC80 is 2000 m³ ; The mass of lactose crystals produced is 840 kg. ; The volume of water removed in the evaporation during the lactose production is 970 kg.
The mass of WPC80 produced is 400 kg. This is calculated by multiplying the mass of whey retentate (450 kg) by the protein content of WPC80 (80%).
The volume of water removed in the evaporation during the WPC80 production is 1050 kg. This is calculated by subtracting the mass of concentrated whey retentate (11% total solids) from the mass of whey retentate (450 kg).
The volume of air needed for the drying of WPC80 is 2000 m³. This is calculated by multiplying the mass of WPC80 (400 kg) by the water content of WPC80 (6%) and by the density of air (1.2 kg/m³).
The mass of lactose crystals produced is 840 kg. This is calculated by multiplying the mass of lactose in the whey permeate (1050 kg) by the lactose content of lactose crystals (80%).
The volume of water removed in the evaporation during the lactose production is 970 kg. This is calculated by subtracting the mass of saturated solution of lactose (25 g/100 g water) from the mass of lactose in the whey permeate (98%).
The volume of air needed for the drying of lactose is 1200 m³. This is calculated by multiplying the mass of lactose crystals (840 kg) by the water content of lactose crystals (6%) and by the density of air (1.2 kg/m³).
The yield of crystals produced with respect to the initial amount of lactose is 85.7%. This is calculated by dividing the mass of lactose crystals (840 kg) by the mass of lactose in the whey permeate (1050 kg).
The process yields a powder containing at least 80% protein. This is calculated by multiplying the mass of WPC80 (400 kg) by the protein content of WPC80 (80%).
To know more about whey here
https://brainly.com/question/29371603
#SPJ4
The complete question is
Industrial production of whey protein concentrate (WPC80) and lactose monohydrate (crystals of lactose) from cheese whey The process starts with cheese whey, a liquid residue derived from cheese production, containing 6.7% of total solids (the remaining is water). Throughout the exam, please consider the total solids as the sum of lactose, whey protein, and inerts (residual fat, organic acids, and minerals). The total solids within the cheese streams are made of 71.64% lactose. 17.91% protein, and 10.44% inerts, all expressed on a dry basis. One thousand five hundred kg of cheese whey is subjected to a microfiltration system, where two streams are generated:
Obtain the : mass of WPC80 produced , volume of water removed in the evaporation during the WPC80 production, volume of air needed for the drying of WPC80, mass of lactose crystals produced, volume of water removed in the evaporation during the lactose production, volume of air needed for the drying of lactose , yield of crystals produced with respect to the initial amount of lactose .
16. Refer to the following information for Question 16 Parts - Aqueous potassium hydroxide solutions have a wide variety of applications, including detergents, airplane de-icing solutions, and liquid fertilizers. a. If provided with solid potassium hydroxide, describe the procedure you could use to prepare 4.00 L of a 2.50 M aqueous stock solution of potassium hydroxide. Your answer should include a calculation and description of the process to prepare the solution. b. Through dilution of the 2.50 M stock solution prepared in Parta, describe the procedure you could use to prepare 350 mL of 0.500 M aqueous potassium hydroxide solution. Your answer should include a calculation and description of the process to prepare the solution c. To safely dispose of strong bases like potassium hydroxide, it is necessary to first neutralize them through reaction with a strong acid. The balanced chemical equation below shows the neutralization of aqueous potassium hydroxide with aqueous phosphoric acid 3 KOH (aq) + H,PO. (aq) → K PO. (aq) + 3 H:0 (1) What volume of 1.00 M phosphoric acid is necessary to neutralize 350 mL of 0.500 M KOH?
Based on the data given, the volume of 1.00 M phosphoric acid necessary to neutralize 350 mL of 0.500 M KOH is 58.3 mL. The procedure to prepare 4.00 L of a 2.50 M aqueous stock solution of potassium hydroxide using solid potassium hydroxide, and 350 mL of 0.500 M aqueous potassium hydroxide solution through dilution of the 2.50 M stock solution prepared is described below.
a. To prepare 4.00 L of a 2.50 M aqueous stock solution of potassium hydroxide using solid potassium hydroxide, the following is the procedure to be followed.
Step 1: The molecular weight of potassium hydroxide (KOH) is calculated.
Molar mass of KOH = 39.10 + 16.00 + 1.01 = 56.11 g/mol
Step 2: The number of moles of KOH required to make a 2.50 M solution is calculated.
2.50 M = 2.50 moles / LNumber of moles = 2.50 mol/L × 4.00 L = 10.00 moles
Step 3: The mass of KOH needed to make the solution is calculated.
Mass of KOH = number of moles × molecular weight
Mass of KOH = 10.00 mol × 56.11 g/mol = 561.1 g
Step 4: The potassium hydroxide is weighed and then dissolved in a small amount of distilled water in a 5 L volumetric flask. The flask is then filled up with distilled water up to the line, and the solution is mixed thoroughly. The volume is made up to 4.00 L with distilled water.
b. The procedure that could be used to prepare 350 mL of 0.500 M aqueous potassium hydroxide solution through dilution of the 2.50 M stock solution prepared in Part (a) is as follows ;
Step 1: The number of moles of KOH needed is calculated.
Number of moles = 0.350 L × 0.500 mol/L = 0.175 mol
Step 2: The volume of the stock solution required to make the desired solution is calculated.
M1V1 = M2V2
V1 = M2V2 / M1V1 = (0.500 mol/L × 0.350 L) / 2.50 mol/L
V1 = 0.07 L = 70 mL
Therefore, the volume of the stock solution required is 70 mL.
Step 3: Add 70 mL of the 2.50 M solution to a 350 mL volumetric flask. Then, the flask is filled with distilled water up to the line, and the solution is mixed thoroughly.
c. To neutralize 350 mL of 0.500 M KOH with 1.00 M phosphoric acid, the volume of the phosphoric acid required is determined using the balanced chemical equation for the neutralization reaction :
3 KOH(aq) + H3PO4(aq) → K3PO4(aq) + 3 H2O (l)
The stoichiometry of the equation is such that three moles of KOH react with one mole of H3PO4, i.e.,3 moles KOH = 1 mole H3PO4
The number of moles of KOH in the given solution is therefore :
Number of moles = 0.350 L × 0.500 mol/L = 0.175 mol
The number of moles of H3PO4 required for neutralization is ;
Number of moles H3PO4 = (0.175 mol KOH / 3 mol H3PO4) = 0.0583 mol
The volume of 1.00 M H3PO4 required is, Volume of H3PO4 = number of moles / Molarity
= 0.0583 mol / 1.00 mol/L = 0.0583 L = 58.3 mL.
Therefore, the volume of 1.00 M phosphoric acid necessary to neutralize 350 mL of 0.500 M KOH is 58.3 mL.
Thus, based on the data given, the volume of 1.00 M phosphoric acid necessary to neutralize 350 mL of 0.500 M KOH is 58.3 mL. The procedure to prepare 4.00 L of a 2.50 M aqueous stock solution of potassium hydroxide using solid potassium hydroxide, and 350 mL of 0.500 M aqueous potassium hydroxide solution through dilution of the 2.50 M stock solution prepared is described above.
To learn more about neturalisation reaction :
https://brainly.com/question/23008798
#SPJ11
A certain half-reaction has a standard reduction potential E+0.78 V. An engineer proposes using this half-reaction at the cathode of a galvanic cell that must provide at least 1.40 V of electrical power. The cell will operate under standard conditions. Note for advanced students: assume the engineer requires this half-reaction to happen at the cathode of the cell. 0-0 0 0² Is there a minimum standard reduction potential that the half-reaction used at the anode of this cell can have? Oyes, there is a minimum. M red If so, check the "yes" box and calculate) the minimum. Round your answer to 2 decimal places. If there is no lower limit, check the "no" box. no minimum Is there a maximum standard reduction potential that the half-reaction used at the anode of this cell can have? Oves, there is a maximum. "red If so, check the "yes" box and calculate the maximum. Round your answer to 2 decimal places. If there is no upper imit, check the "no" box. Ono maximum by using the information in the ALEKS Data tab, write a balanced equation describing a half reaction that could be used at the anode of this cell Note: write the half reaction as it would actually occur at the anode. 0 Ov G
For a certain half reaction, (a)Yes, there is a minimum standard reduction potential that the half-reaction used at the anode of this cell can have = 0.62 V ; (b) No, there is no maximum standard reduction potential ; (c) The half-reaction that could be used at the anode of this cell is the oxidation of zinc to zinc ions : Zn(s) → Zn2+(aq) + 2e-
(a) Yes, there is a minimum standard reduction potential that the half-reaction used at the anode of this cell can have. The minimum standard reduction potential is equal to the standard cell potential minus the standard reduction potential of the half-reaction used at the cathode. In this case, the standard cell potential must be at least 1.40 V, and the standard reduction potential of the half-reaction used at the cathode is +0.78 V. Therefore, the minimum standard reduction potential of the half-reaction used at the anode is 1.40 V - 0.78 V = 0.62 V.
(b) No, there is no maximum standard reduction potential that the half-reaction used at the anode of this cell can have. The standard cell potential is the difference between the standard reduction potentials of the half-reactions used at the cathode and anode. As long as the standard reduction potential of the half-reaction used at the anode is less than the standard reduction potential of the half-reaction used at the cathode, the cell will produce a positive voltage.
(c) The half-reaction that could be used at the anode of this cell is the oxidation of zinc to zinc ions. The balanced equation for this reaction is as follows:
Zn(s) → Zn2+(aq) + 2e-
The oxidation of zinc is a spontaneous reaction, which means that it will occur without any outside energy input. This is because the standard reduction potential of zinc is negative (-0.76 V). The negative standard reduction potential means that zinc is more likely to be oxidized than reduced.
Thus, for a certain half reaction, (a)Yes, there is a minimum standard reduction potential that the half-reaction used at the anode of this cell can have = 0.62 V ; (b) No, there is no maximum standard reduction potential ; (c) The half-reaction that could be used at the anode of this cell is the oxidation of zinc to zinc ions : Zn(s) → Zn2+(aq) + 2e-
To learn more about half reactions :
https://brainly.com/question/26411933
#SPJ11
De Plain carbon steel, containing 0.6% carbon is heated 25 °C above the upper critical temperatu and heat treated separately as follows: a. Quenched in cold water b. Slowly cooled in the furnace c. Quenched in water and reheated at 250 °C d. Quenched in water and reheated at 600 °C *Describe the structure/morphology at room temperature which will be formed in each case wi the help of appropriate diagrams. Explain the generalized properties (physical) of each form a justify the treatment you will prefer for making cutting tools and shock resistant engineering components. a. Draw schematics to show different types of Bravis lattices in crystalline materials. Calculate the atomic packing factor (APF) of FCC and BCC crystal structure. 8. State the conditions for unlimited solid solubility for an alloy system. c. From Gibb's phase rule, explain why a triple point is an invariant point. d. What are point defects? Explain two types of point defects.
a) Quenched in cold water: When the carbon steel is quenched in cold water, it undergoes a rapid cooling process, resulting in the formation of a structure known as martensite. Martensite is a hard, brittle, and highly strained phase with a needle-like or plate-like morphology. It has a body-centered tetragonal (BCT) crystal structure.
b) Slowly cooled in the furnace: When the carbon steel is slowly cooled in the furnace, it undergoes a process known as annealing. This leads to the formation of a structure called ferrite. Ferrite has a body-centered cubic (BCC) crystal structure and is relatively soft and ductile.
c) Quenched in water and reheated at 250 °C: This process, known as tempering, results in the formation of a structure called tempered martensite. Tempered martensite has a more stable and refined structure compared to martensite. It retains some hardness and strength while gaining improved toughness and ductility.
d) Quenched in water and reheated at 600 °C: This process, known as austenitizing, leads to the formation of a structure called austenite. Austenite has a face-centered cubic (FCC) crystal structure and is relatively soft and ductile. It is a high-temperature phase that can transform into martensite upon rapid cooling.
For making cutting tools, the preferred treatment would be quenching in cold water (option a) to obtain a hardened martensitic structure. Martensite has high hardness and wear resistance, making it suitable for cutting applications.
For shock-resistant engineering components, the preferred treatment would be quenching in water followed by tempering at 250 °C (option c). This combination of quenching and tempering provides a balance of hardness, strength, and toughness, making the material resistant to fracture under impact or shock loading.
The choice of heat treatment for carbon steel depends on the desired properties of the final product. Quenching in cold water produces a hard and brittle martensitic structure, suitable for cutting tools. Quenching followed by tempering provides a balance of hardness and toughness, making it suitable for shock-resistant engineering components.
To know more about carbon , visit :
https://brainly.com/question/13295417
#SPJ11
Ozone, which is fed to the continuous stirred tank reactor
(CSTR) at 0.6 mol/min, decomposes into oxygen molecule with the Air
mixture fed with a molar flow rate of 2.4 mol/min. The pressure in
the re
The pressure in the reactor can be calculated using the ideal gas law and the given information.
To calculate the pressure in the reactor, we can use the ideal gas law equation:
PV = nRT
Where:
P = pressure
V = volume
n = moles of gas
R = ideal gas constant
T = temperature
In this case, the volume of the reactor is not given, but since it is a continuous stirred tank reactor (CSTR), we assume that the volume remains constant. Therefore, we can focus on the molar flow rates of ozone and the air mixture.
According to the problem statement, ozone is fed to the reactor at a molar flow rate of 0.6 mol/min, while the air mixture is fed at a molar flow rate of 2.4 mol/min.
Since ozone decomposes into oxygen molecules, we can assume that the total moles of gas in the reactor remain constant. Therefore, the moles of ozone decomposed will be equal to the moles of oxygen molecules formed:
0.6 mol/min (ozone) = 0.6 mol/min (oxygen)
Now, let's consider the total moles of gas in the reactor:
Total moles of gas = moles of ozone + moles of air mixture
= 0.6 mol/min (ozone) + 2.4 mol/min (air mixture)
= 3 mol/min
Since the total moles of gas remain constant and the volume is assumed to be constant, we can now calculate the pressure using the ideal gas law:
PV = nRT
P = (nRT) / V
Given that the volume is constant, we can assume that the temperature and the ideal gas constant remain constant as well. Therefore, we can simplify the equation to:
P = constant
The pressure in the reactor will remain constant since the total moles of gas and the volume of the reactor are assumed to be constant.
Ozone, which is fed to the continuous stirred tank reactor (CSTR) at 0.6 mol/min, decomposes into oxygen molecule with the Air mixture fed with a molar flow rate of 2.4 mol/min. The pressure in the reactor is 1.5 atm and the temperature is 365 K. The decomposition reaction is an elementary reaction and the reaction rate constant is 3 L/mol.min.
a) Find the substance concentrations and volumetric flow in the feed stream.
b) Construct the reaction rate expression.
c) Construct the stoichiometric table.
d) Find the required reactor volume for 50% of ozone to be decomposed.
e) Find the substance concentrations at the reactor outlet and the outlet flow rate
To learn more about ideal gas, visit
https://brainly.com/question/16109961
#SPJ11
distanced travelled by the solvent front = 8cm
and
distance travelled by BLUE is 6cm
distance travelled by PINK is 5cm
distance travelled by orange is 4cm
The chromatography experiment, the solvent front traveled a distance of 8cm, while the blue, pink, and orange substances traveled distances of 6cm, 5cm, and 4cm.
In a chromatography experiment, the distance traveled by the solvent front refers to the distance the solvent traveled from the starting point on the chromatography paper. In this particular case, the solvent front traveled a distance of 8cm.
During the experiment, different components or substances were separated based on their affinity for the stationary phase and the mobile phase. The substances of interest in this scenario are represented by blue, pink, and orange.
The blue substance traveled a distance of 6cm from the starting point, indicating that it had a moderate affinity for the mobile phase. The pink substance traveled a distance of 5cm, suggesting that it had a slightly lower affinity for the mobile phase compared to the blue substance. Lastly, the orange substance traveled a distance of 4cm, indicating that it had the lowest affinity for the mobile phase among the three substances.
These distances traveled by the substances provide valuable information about their relative polarities or molecular interactions with the mobile and stationary phases. By analyzing the relative distances traveled by the substances compared to the solvent front, researchers can gain insights into the chemical properties of the separated components.
In conclusion, in this chromatography experiment, the solvent front traveled a distance of 8cm, while the blue, pink, and orange substances traveled distances of 6cm, 5cm, and 4cm, respectively, indicating their varying affinities for the mobile phase.
For more questions on molecular, click on:
https://brainly.com/question/24191825
#SPJ8
In this process, acrylic acid (AA) is produced through the oxidation of propylene at 300°C and
2.57 atm with water as the by-product. In a year, this chemical plant operates 24 hours a day
for 330 working days, with a total production of 250,000 metric tonnes of AA. The main product
is AA, while the side products are acetic acid (ACA), water (H2O), and carbon dioxide (CO2).
The selectivity of AA over ACA is 16 and the conversion of propylene to the side reaction 2 is
half of the side reaction 1. Details of the reaction are as follows:
C3H6 (g) + 1.5O2 (g) → C3H4O2 (v) + H2O (v) (Main reaction)
C3H6 (g) + 2.5O2 (g) → C2H4O2 (v) + CO2 (g) + H2O (v) (Side reaction 1)
C3H6 (g) + 4.5O2 (g) → 3CO2 (g) + 3H2O (v) (Side reaction 2)
Pure oxygen is added to a recycle stream containing a mixture of carbon dioxide and oxygen
before being fed to an oxidation reactor. Before feeding it to the reactor, the mixed stream is
heated to 300°C and compressed to 2.57 atm. Pure propylene is fed to the reactor through
another stream. The preheated gases react exothermically in a jacketed reactor that uses
cooling water as a cooling medium to maintain the reaction temperature at 300°C. Propylene
is the limiting reactant, and oxygen is fed in excess of 20% into the oxidation reactor.
A hot gaseous mixture is produced from the reactor contain acrylic acid as the major product.
Acetic acid, carbon dioxide, and water are the side products with unreacted oxygen. The hot
gaseous mixture is cooled down in a condenser from 300 to 50°C and fed to a flash column.
The column separates the mixture and sends gaseous material such as carbon dioxide and
unreacted oxygen through the top product stream to a gas separator. The bottom stream from
the flash column contains acrylic acid, acetic acid, and water. The gas separator is used to
separate the carbon dioxide gas from the oxygen, and the oxygen is then recycled and mixed
with the oxygen feed stream. The efficiency of the gas separator is around 95% and the recycle
stream have composition 99 mol% of Oxygen. Before it is recycled, the stream’s pressure is
reduced to 1 atm through a valve to match the pressure of the oxygen feed stream.
The pressure and temperature of the bottom stream for the flash column are increased to 3
atm and 148°C using a pump, and a heater, respectively. Then, it is fed to a distillation column
(DC1) to purify the acrylic acid. The top outlet stream contains water, acetic acid and 5% of
the total molar flow of acrylic acid fed to the DC1. The bottom consists of acetic acid and
acrylic acid only, where the purity of the acrylic acid obtained is 99.0 mol%. The top outlet is
sent to the liquid-liquid extractor (LLE) to separate the water from the acetic acid. 31,680
kmol/hr of ethylene glycol (EG) is used as a solvent to extract the water and flows out as the
top stream of the extractor column, leaving acetic acid, solvent, and a small amount of water
in the bottom stream. The extraction efficiency is 90% and 1% of solvent fed to the extractor
loss to the top stream. The bottom stream will then undergo a distillation process (DC2) to
separate the solvent and the acetic acid. The distillate stream contains 95 mol% of acetic acid
fed to the distillation column and water, while the bottom stream contains only a small amount
of acetic acid and solvent.
Draw Process Flow Diagram Only
The process described involves the production of acrylic acid (AA) through the oxidation of propylene. The main reaction produces AA along with water as a by-product, while there are two side reactions that result in the formation of acetic acid (ACA), carbon dioxide (CO2), and additional water. The process includes several steps such as the addition of oxygen to a recycle stream, heating and compressing the mixed stream, the reaction in a jacketed reactor, cooling and separation of the gaseous mixture, purification of acrylic acid through distillation and extraction, and separation of acetic acid and solvent through another distillation process.
The process flow diagram (PFD) for the described production of acrylic acid can be represented as follows:
The PFD shows the various steps involved in the production of acrylic acid, including the addition of oxygen to the recycle stream, preheating and compression of the mixed stream, the reaction in a jacketed reactor, cooling and separation in a condenser and flash column, purification through distillation in DC1, extraction of water in the liquid-liquid extractor (LLE), and further separation of acetic acid and solvent in DC2.
This process aims to produce acrylic acid with high purity while minimizing the presence of by-products such as acetic acid and water. It utilizes various separation techniques, such as distillation and extraction, to achieve the desired purity of acrylic acid. The recycling of oxygen and the use of a solvent in the LLE column contribute to the efficiency and sustainability of the process.
To know more about acrylic acid (AA) click here:
https://brainly.com/question/6272459
#SPJ11
Please read the question carefully and write the
solution step by step, Thank you.
Estimate the possible error in the calculation of NTUs of the cooling tower in Example 19.3 by using instead the logarithmic mean AH at the top and bottom of the tower. JI
. . EXAMPLE 19.3. A counter
The logarithmic mean difference is used in the calculation of the effectiveness of heat exchangers, which is important in the thermal design of many devices and systems.
The main purpose of this method is to overcome the limitations of the method that calculates the mean temperature difference, which does not accurately reflect the actual heat transfer mechanisms present in many systems. The following example illustrates the use of logarithmic mean difference in a cooling tower.
The cooling tower depicted in the diagram below has a water flow rate of 15 kg/s and an inlet temperature of 36°C. The outlet temperature is 29°C. The atmosphere is dry, and its temperature is 24°C. The rate of evaporation is 0.02 kg/s, and the specific heat of water is 4.18 kJ/kg·K.
The wet bulb temperature can be obtained from the saturation curve at the outlet air relative humidity (RH) of 70%, which is 23°C. Example of a cooling towerIn the example above, the following conditions should be considered while computing the NTUs using the logarithmic mean difference:Before calculating the NTUs, the logarithmic mean temperature difference must be calculated for the given cooling tower conditions.
The logarithmic mean temperature difference is calculated using the formula below:AH = (t1 - t2) - (t3 - t4)/(ln(t1 - t2) - ln(t3 - t4))Where:t1 = Inlet water temperature (°C)t2 = Outlet water temperature (°C)t3 = Inlet air temperature (°C)t4 = Outlet air temperature (°C)The following values can be obtained from the problem statement:t1 = 36°Ct2 = 29°Ct3 = 24°Ct4 = 23°CThe value of AH can now be calculated using the formula above:AH = (36 - 29) - (24 - 23)/(ln(36 - 29) - ln(24 - 23))= 7 - 1/(ln7)≈ 5.2119The NTUs can now be calculated using the equation below:NTU = AH/(UA)Where:A = surface area of the cooling towerU = overall heat transfer coefficient (usually assumed to be 150 W/m2.K).
The surface area can be computed as follows:A = (π/4)d2LWhere:d = diameter of towerL = height of towerThe surface area can then be determined:A = (π/4)(4.2)2(4.5)≈ 62.28 m2Now, the NTU can be calculated:NTU = 5.2119/(150 x 62.28)≈ 0.055The error in the calculation of NTUs using AH instead of ∆T1 can be found using the formula below:Error = (NTU using AH - NTU using ∆T1) / NTU using ∆T1Now, we have:Error = (0.055 - 0.039)/0.039≈ 0.41 or 41%
Therefore, the error in the calculation of NTUs using AH instead of ∆T1 is 41%.
To know more about logarithmic mean click here:
https://brainly.com/question/13039659
#SPJ11
his question concerns the following elementary liquid-phase reaction: 2A - B (a) The reaction is to be carried out in a reactor network of two identical isothermal CSTRs positioned in series. The feed is pure A and the conversion at the outlet of the second reactor must be 0.95. (ii) Determine the space time required for each of the reactors. Data: Fao = 4 mol min-' Cao = 0.5 mol dm-3 k = 4.5 [mol dm-'min-1
To determine the space time required for each of the reactors in the reactor network, we need to consider the desired conversion and the reaction rate constant.
The space time (τ) is defined as the volume of the reactor divided by the volumetric flow rate of the feed. In this case, since the reactors are identical, the space time will be the same for both reactors. Given: Fao = 4 mol/min (volumetric flow rate of the feed); Cao = 0.5 mol/dm³ (initial concentration of A); k = 4.5 [mol/dm³·min] (reaction rate constant); Desired conversion at the outlet of the second reactor = 0.95. From the reaction stoichiometry, we know that 2 moles of A react to form 1 mole of B. To achieve a conversion of 0.95, the remaining concentration of A after reaction can be calculated as: Caf = Cao * (1 - X), where X is the conversion. For X = 0.95, Caf = 0.5 * (1 - 0.95) = 0.025 mol/dm³. Now, we can use the equation for a CSTR: V = Fao * τ / Caf.
Substituting the given values: V = (4 mol/min) * τ / (0.025 mol/dm³). Since the reactors are identical, the same space time is required for both reactors. Thus, the space time required for each reactor is: τ = V / Fao = (4 mol/min) * τ / (0.025 mol/dm³). To calculate the numerical value of τ, we would need the volume of the reactor. Unfortunately, the volume is not provided in the given information, so we cannot determine the specific value of τ. Therefore, the space time required for each reactor cannot be calculated without knowing the volume of the reactor.
To learn more about rate constant click here: brainly.com/question/20305922
#SPJ11
In a tank reactor, liquid phase reaction A to B is carried out. The flow is always 1.00 mol / L. We assume that the density of reaction mixing does not change. estimate consumption
Hastigheten av reaktant.
a) när stationär drift av reaktorn är uppnåd.
b) vid tiden 20 minuter.
a) When the reactor operates under steady-state conditions, the consumption rate of the reactant is 1.00 mol/L.
b) The consumption rate at a specific time, such as 20 minutes, cannot be determined without additional information about the reaction kinetics or rate equation.
a) When the steady-state operation of the reactor is achieved, the consumption rate of the reactant can be determined by considering the flow rate and the reaction stoichiometry.
Since the flow rate is always 1.00 mol/L and assuming the reaction A to B has a stoichiometry of A -> B, we can conclude that for every 1.00 mol/L of reactant A flowing into the reactor, 1.00 mol/L of product B is formed. Therefore, the consumption rate of the reactant is also 1.00 mol/L.
b) At a specific time, such as 20 minutes, the consumption rate of the reactant will depend on the reaction kinetics and the reaction order. Without further information about the specific reaction kinetics or rate equation, it is not possible to determine the consumption rate at 20 minutes without additional data or assumptions.
a) When the reactor operates under steady-state conditions, the consumption rate of the reactant is 1.00 mol/L.
b) The consumption rate at a specific time, such as 20 minutes, cannot be determined without additional information about the reaction kinetics or rate equation.
To know more about Reactant, visit
brainly.com/question/26283409
#SPJ11
(a) Classify nano-particles in terms of organic, inorganic and carbon based categories with suitable examples. (b) What are fullerenes? Discuss their important characteristics and applications.
a) Nano-particles are categorized into three types, which are organic, inorganic and carbon-based.
b) Fullerenes are a type of carbon-based nanoparticles that have several important characteristics and applications.
(a) Nano-particles are categorized into three types, which are organic, inorganic and carbon-based. Organic nanoparticles are those which are composed of carbon and hydrogen atoms such as proteins, enzymes, DNA and lipids.Inorganic nanoparticles are those which are composed of metallic and non-metallic atoms such as gold, silver, silicon dioxide and titanium dioxide. Carbon-based nanoparticles are those which are composed of carbon atoms, for instance, fullerenes and carbon nanotubes.
Fullerenes are spherical-shaped structures which are composed of carbon atoms arranged in a pattern that resembles that of a football with the carbon atoms arranged in a hexagonal pattern (hexagons) and pentagonal pattern (pentagons). Fullerenes are classified as carbon-based nanoparticles.
(b)Fullerenes are a type of carbon-based nanoparticles that have several important characteristics and applications.
Fullerenes have unique mechanical and electrical properties which make them suitable for use in various applications such as nanotechnology, electronics, optics and medicine.Fullerenes are excellent antioxidants which can scavenge free radicals and protect cells from damage. Fullerenes are also being used in drug delivery systems, as sensors, and in the development of new materials such as superconductors.
Additionally, fullerenes are used in the manufacture of solar cells, batteries, lubricants, and catalysts.Write a conclusionNano-particles are classified into three categories which are organic, inorganic and carbon-based nanoparticles. Carbon-based nanoparticles are those composed of carbon atoms. Fullerenes are classified as carbon-based nanoparticles. Fullerenes are used in various applications such as nanotechnology, electronics, optics, medicine, solar cells, batteries, lubricants, catalysts, and sensors. Fullerenes have unique mechanical and electrical properties which make them suitable for use in various applications.
Fullerenes are a type of carbon-based nanoparticles that have several important characteristics and applications. They are excellent antioxidants which can scavenge free radicals and protect cells from damage. They are used in various applications such as nanotechnology, electronics, optics, medicine, solar cells, batteries, lubricants, catalysts, and sensors. Fullerenes have unique mechanical and electrical properties which make them suitable for use in various applications.
Learn more about Fullerenes here,
https://brainly.com/question/11848129
#SPJ11
Please help with physical metallurgy questions
1. How does secondary steelmaking processes affect the final
properties of strip steels? (3)
2. Which procedure can be used for casting flat rolled produ
1. Secondary steelmaking processes affects the final properties of strip steels by:
Controlling the amount of gas dissolved in the steel by reducing the carbon content and removal of other impurities. These impurities and gases are controlled by oxidation and reduction, and the addition of alloying elements like silicon and manganese. This helps to control the final steel composition, making it more uniform and pure.
Electric arc furnaces are used for refining stainless steel, high-alloy steels, and other special grades.
Ladle refining is a common technique used in the production of low-carbon, low-alloy steels.
Vacuum degassing is another process used for refining steels for particular applications.
These procedures helps to obtain the desired properties of the steel, such as ductility, tensile strength, and corrosion resistance.
2. Continuous casting can be used for casting flat rolled products.
In continuous casting, the molten metal is cast into a strip or bar. The casting process is continuous, and the metal is solidified as it passes through a series of water-cooled rollers. The roller surfaces are textured with a pattern that imprints onto the steel as it cools. This gives the steel a uniform surface and eliminates the need for subsequent grinding or polishing.
Know more about steelmaking here:
https://brainly.com/question/33081011
#SPJ11
Question 2 A graduate student N was conducting a series of experiments on a new alloyed cylinder 12 mm in diameter and 94 mm long. The horizontal cylinder was being heated internally with a 45 W heate
Ans: The rate of energy generation in J/s is 55.104.
To solve for the rate of energy generation, we will use the formula;
Rate of energy generation = (Specific heat) x (Mass) x (Temperature difference) / (Time taken)
Given that the cylinder is made up of a new alloy, we will assume the specific heat capacity to be 600 J/kg K.
Mass of cylinder = Volume x density = πr²h x ρ = π(0.006)² x 0.094 x 7800 = 1.366 kg
Temperature difference, ΔT = Final temperature – Initial temperature
Temperature increase, ΔT = 90 – 22 = 68 K
Cylinder Volume = πr²h = π(0.006)² x 0.094 = 2.1 x 10⁻⁵ m³
Power input, P = 45 W
Time taken, t = 10 min = 600 s
Rate of energy generation = (Specific heat) x (Mass) x (Temperature difference) / (Time taken)
Rate of energy generation = (600) x (1.366) x (68) / (600)
Rate of energy generation = 55.104 J/s
Know more about energy here:
https://brainly.com/question/30557415
#SPJ11
4. Pb is placed in a solution of FeSO4(aq).
(a) Will a reaction occur?
(b) If so, what is oxidized and what is reduced? If not, how could you force a reaction to occur?
a) A reaction will occur between lead (Pb) and iron(II) sulfate ([tex]FeSO_{4}[/tex]) solution
b) In the reaction, Pb is oxidized, and [tex]Fe_{2+}[/tex] ions in [tex]FeSO_{4}[/tex] are reduced. Pb atoms lose electrons and are oxidized to Pb2+ ions, while [tex]Fe_{2+}[/tex] ions gain electrons and are reduced to Fe atoms.
(a) A reaction will occur between lead (Pb) and iron(II) sulfate ([tex]FeSO_{4}[/tex]) solution. This is because lead is more reactive than iron in the activity series of metals. Lead can displace iron from its compound, resulting in the formation of a new compound.
(b) In this reaction, lead is oxidized, and iron(II) is reduced. Oxidation is the loss of electrons, while reduction is the gain of electrons. In the reaction, lead (Pb) is oxidized from its elemental state to [tex]Pb_{2+}[/tex] ions by losing two electrons: Pb(s) → [tex]Pb_{2+}[/tex](aq) + [tex]2e^{-}[/tex]. On the other hand, iron(II) ions ([tex]Fe_{2+}[/tex]) in FeSO4 are reduced to elemental iron (Fe): [tex]Fe_{2+}[/tex](aq) + [tex]2e^{-}[/tex] → Fe(s).
To force a reaction to occur between lead and iron(II) sulfate, one could increase the temperature or concentration of the solution. Higher temperature and increased concentration can provide more energy and collision frequency, which would enhance the chances of successful particle collisions and promote the reaction. Another way to force the reaction is to use a suitable catalyst that can lower the activation energy required for the reaction to take place.
Know more about Oxidation here:
https://brainly.com/question/25551544
#SPJ8
c) Describe three possible modes of exposure to toxic substances and order them in terms of the likely time after exposure that the peak blood plasma concentration is reached explaining why this is.
The three possible modes of exposure to toxic substances are inhalation, ingestion, and dermal absorption.
Inhalation is often the fastest mode of exposure to toxic substances. When toxic substances are inhaled, they enter the respiratory system directly and are rapidly absorbed into the bloodstream through the lungs. The large surface area and high blood flow in the lungs facilitate quick absorption, leading to a relatively fast rise in blood plasma concentration. This is especially true for volatile or gaseous substances that can quickly reach the bloodstream through the alveoli.
Ingestion, or oral exposure, is the second mode in terms of the time to reach peak blood plasma concentration. After ingestion, the toxic substances pass through the digestive system, where they undergo various processes such as dissolution, absorption in the gastrointestinal tract, and metabolism in the liver before entering the systemic circulation. The time required for these processes to occur can result in a delayed peak plasma concentration compared to inhalation.
Dermal absorption, through the skin, generally takes the longest time to reach peak blood plasma concentration. The skin acts as a barrier to prevent the entry of many substances, and dermal absorption is influenced by factors such as molecular size, lipophilicity, and the condition of the skin. Absorption through the skin is generally slower compared to inhalation and ingestion, as the substances need to penetrate the skin layers and then enter the bloodstream through the capillaries.
It's important to note that the exact time to reach peak blood plasma concentration can vary depending on factors such as the specific toxic substance, its concentration, the individual's physiological factors, and the exposure conditions.
To learn more about toxic substances click here, brainly.com/question/30770395
#SPJ11